Providing & fixing paver block, parking shed, sewage treatment plant (100 KLD) Video conference room at Rajpipla district jail, Rajpipla dist. Narmada (Including Electrification) [3rd Attempt]

No. InFigure In Words Rs.

Excavation for foundation in Loose or soft soil upto 1.5 mt. depth including sorting out and

stacking of useful materials and disposing of the excavated stuff upto any Lead & Lift. Rs. One Hundred Twenty Four &

Paise Sixty One Only

Excavation for foundation in Dense or Hard soil upto 1.5 mt. depth including sorting out and

stacking of useful materials and disposing of the excavated stuff upto any Lead & Lift. Rs. One Hundred Fifty Nine & Paise

Thirty Only

Providing & laying Cement Concrete 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone

aggrigates of 40 mm nominal size) curing complete excluding cost of formwork in Rs. Three Thousand Thirty Three &

FOUNDATION AND PLINTH. Paise Thirty Three Only

Providing & laying Cement Concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone

aggrigates of 20 mm nominal size) curing complete excluding cost of formwork in Rs. Three Thousand Five Hundred

FOUNDATION AND PLINTH. Fifty Five & Paise Sixty Six Only

Providing & laying Cement Concrete 1:4:8 ( 1 cement : 4 coarse sand : 8 graded stone

aggrigates of 40 mm nominal size) curing complete excluding cost of formwork in Rs. Two Thousand Seven Hundred

FOUNDATION AND PLINTH. Eleven Only

BRICK WORK using common burnt clay building bricks having crushing strength not less

than 35 Kg./Sq. cm. In Foundation & Plinth in cement mortar 1 : 6 ( 1 cement : 6 coarse sand ( Rs. Four Thousand Two Hundred

Conventional Bricks). Thirty Seven & Paise Sixty Only

FILLING in plinth with SAND under floors including watering, raming consolidating and

Rs. Four Hundred Eighty Four &

7 dressing etc. complete. 16.00 Cum 484.44

Paise Forty Four Only

Providing & laying Controlled CEMENT CONCRETE M-150 and curing complete including

the cost of formwork of Plywood only with fair finish & Proping must be of steel only so as to

give fair finish but excluding the cost of reinforcement in Rcc Grade Slab. Providing and Rs. Three Thousand Eight Hundred

Mixing Plasticiser in cement concrete as per mix design including rate of labour,material etc.as Seven & Paise Six Only

per direction of Engineer in charge.

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

Providing & laying Controlled CEMENT CONCRETE M-250 and curing complete including

cost of formwork Plywood only with fair finish & Proping must be of steel only so as to give

fair finish but excluding the cost of reinforcement in column FOOTING base of columns and

Rs. Four Thousand Five Hundred

9 Mass concrete. Providing and Mixing Plasticiser in cement concrete as per mix design 4.00 Cum 4522.02

Twenty Two & Paise Two Only

including rate of labour,material etc.

Providing & laying Controlled CEMENT CONCRETE M-250 and curing complete including

cost of formworkof Plywood only with fair finish & Proping must be of steel only so as to give

fair finish but excluding the cost of reinforcement in COLUMN upto PLINTH for any cross

Rs. Eight Thousand Eight Hundred

10 sectional area of column. Rate are also inclusive of providing and mixing Plasticiser in cement 4.00 Cum 8893.05

Ninety Three & Paise Five Only

concrete as per mix design etc.

Providing and laying Controlled cement concrete M-250 and finishing smooth with curing

etc.. complete including the cost of formworkof Plywood only with fair finish & Proping must

be of steel only so as to give fair finish but exculding the cost of reinforcement for PLINTH Rs. Seven Thousand One Hundred

11 BEAMS of any cross sectional area of beam. Rate are also inclusive of providing and mixing 3.00 Cum 7169.87 Sixty Nine & Paise Eighty Seven

Plasticiser in cement concrete as per mix design etc. Only

Filling avaliable excavated earth ( excluding rock) in trenches, plinth sides of foundations etc.

in layers not exceeding 20cms. in depth consolidating each deposited layer by ramming and Rs. One Hundred Thirty Six & Paise

watering. Eleven Only

Providing TMT Bars Fe500D reinforcement of approved brand of GSPHC ONLY for RCC

work including cutting, bending, binding and placing in position etc.complete for all floors. Rs. Seventy Six & Paise Fifty Two

Providing , Fabricating and fixing M.S. GRILL/GATE of approved pattern fabricated from

M.S. flat,square bars, round bars,c-channel, box pipe as per detail Drawings. Rate is including

welding. Rate is also including two coats of Oil paint and one coat of yellow Zinc Cromet

Rs. Seventy Five & Paise Twenty

14 primer coat of approved brand only oil paint shall be used as per approval materials list of 22993.00 Kg. 75.20

GSPHCL Steel Used Must Be ISI Make List.

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

providing and corrogulated JSW pre coated sheet roofing fixed withh galvanised iron J or L

hooks, bolts and Nuts 8 mm dia with bitumin and G.I. Limpet washer or G.I. limpet washer

Rs. Nine Hundred Eighty Four &

15 with white lead complete excluding the cost of Purlines , rafters and trusses(0.60mm thick) 300.00 Sqm 984.37

Paise Thirty Seven Only

Providing and Laying 60mm thick Rubber Mould Paver block of M-30 grade made by Block

making machine with strong vibratory compaction and of approved size and design in

required colour and pattern over and including 50mm thick compacted bed of course sand etc. Rs. Six Hundred Ninety Eight &

complete as directed by engineer in charge Paise Ninety Six Only

17 Designing (hydraulic, process. structural & aesthetic), providing, construction, hydraulic

testing,commissioning of Sewage Treatment Plant of Capacity 100000 ltr per day (100 KLD)

and giving satisfactorily trial run for 3 months of STP consisting of inlet Chamber, Screen

chamber, Grit Separator, MBBR (Based on technologies providing attached growth on plastic

media kept suspended in the sewage due to low density of plastic & provided with diffused air

for aeration with tank, Secondary Clarifier, Sludge collection sump, Gravity Sludge Thickener,

Chlorine Contact Tank, Chlorinator room, Sludge Dewatering Equipment,associated piping

work with required valves, gates, drains. Administration Block cum Laboratory, associated

buldings, Laboratory Equipments, inclusive of mandatory spare parts and instrumentation, etc

complete as turnkey jobs with all involved , electrical, instrumentation and mechanical works

inclusive of following items, units as per detailed specifications for civil, electrical,

instrumentation and mechanical components with all duties and taxes etc. commplete to Rs.Fifty four lakh fifty three

achieve BOD<10ppm,TSS< 10ppm, Biological TN < 10ppm & PO4 < 2ppm to get recyclable thousand three hundred

quality of water for industrial/agricultural purposes. The Coagulant Desing System is

mandatory for chemical phosphorus removal..If so required for the complete working of the

STP and have it approved by GSPHCL.All the materials & componant of STP Shell be of

approved brand & make by GSPHCL Only.

Min. freeboard of 0.3m shall be maintained unless otherwise asked for 0.5m stipulated for

specific units.

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

A PRIMARY TREATMENT

1.1 Bar screen Chamber : Supply, installation, testing & commissioning of 2 Nos. SS-304

Perforated, Screens with suitable lifting arrangement to be fitted with in Bar Screen Chamber

as per STP Manufacturer's design.

1.2 Oil & grease Chamber : Supply, installation, testing & commissioning of Manual

overflow type Oil Removal trap for removal of Oil & Grease from Chamber.

1.3 Collection cum Equilization tank: Tank will be in RCC _ Civil Contractor Scope and the

tank shall have Retention time of Minimum 8 Hours. Course Bubble aeration will be provided

in the tanks.Design included and to be approved by department GSPHC.

1.4 Raw Sewage Transfer Pump :Supply, installation, testing & commissioning of non-clogging

submersible pumps complete with all accessories, motor of required capacity. Delivery

header with check valve, level controller (with wiring) to control the level of sump

automatically.

No. of pumps: 02 Nos. (1 Working + 1 Standby).

B SECONDARY TREATMENT

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

2.1 Process Tanks : Material of construction shall be in MS + FRP : MS sheet thickness 6.0 mm

and Internal FRP lining shall be 2.0 mm. Outside Epoxy Painted.

2.1.1. Anoxic Tank : As per STP Manufacturer's design

2.1.2. Aeration Tank : Aeration Tank shall have suitatble MBBR Media As per STP

Manufacturer's design. Fine Bubble aeration shall be provided with Air Blower (No of Blowers

: 1 Working + 1 Standby)

2.1.3 Tube Settler \ Lamella Settler : Tank with Tube Deck media \ Lamella Plates and

Recirculation Pumps (No. of pumps: 02 Nos. (1 Working + 1 Standby)) As per STP

Manufacturer's design.

2.1.4 Chlorine Contact tank: As per STP Manufacturer's design. Chlorine dosing shall be

provided with tanks and dosing Pumps (No of Pump : 01 No and No of Tank : 01) for

disinfection Purpose.

2.1.5 Sludge Holding Tank: Tank As per STP Manufacturer's Design. Filter press of suitable

capacity along with Feed Pump ((No. of pumps: 02 Nos. (1 Working + 1 Standby)) as per STP

Manufacturer's design.

C TERTIARY TREATMENT

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

3.1 Filter Feed Pump : Supply, installation, testing & commissioning of pumps complete with

all accessories, motor of required capacity. Delivery header with check valve, level controller

(with wiring) to control the level of sump automatically. No. of pumps: 02 Nos. (1 Working +

1 Standby).

3.2 Multigrade Filter: Supply, installation, testing & commissioning of Filter complete

with all accessories, Isolation Valves, Vessel media and Piping

3.3 Activated Carbon Filter: Supply, installation, testing & commissioning of Filter

complete with all accessories, Isolation Valves, Vessel media and Piping

3.4 Treated Water tank: Tank will be in RCC _ Civil Contractor Scope and the tank shall have

Retention time of Minimum 8 Hours. Design of tank is included which to be approved from

GSPHC Structure department.

D 4.0 Control Panel for Sewage Treatment Plant & Cabling Work :

4.1Supply ,Installation ,Installation & Commissioning of Common control panel

(compartmental type) and Cabling for all electrical items like sewage transfer pumps, air

blowers, filter feed pumps, sludge removal pump as well as dosing system.(Details

Attached Below)

4.2 SLD & A Drawing of panel shall be approved by Executive Engineer (Ele.)Panel

Manufacture Shall be approved by EIC as per Tender specification and make list

5.0 Inter Connecting Pipe Work within Battery Limit : 01 Set. Sewage Pipe line Shall be UPVC.

Air line shall be MSEP. Submerged air lines shall be in UPVC. Clear Water shall be in UPVC.

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

(1) All Civil works finished with water proofing, plaster, Outside & Inside colour as per

GSPHC list, structure duly tested for leak-proofing, plant room flooring, pumps foundations

etc. and related S.S/MS/CI works such as supply and fixing of handrails, manholes, gratings,

grills, doors, vents, footrests etc. shall be in the scope of the Main Civil Contractor.

(2) All Civil Tanks shall be constructed in RCC as per STP manufactures drawing &

STRUCTURAL Design.Design to be approved by structure department of GSPHC

(3) If anything required to achieve the mentioned parameters and completing treatment

process shall be in STP Manufacturer's scope.

B. Chemical & Consumable Charges for Comprehensive (all inclusive) annual maintenance

service contract of the above STP system as per the terms and conditions of the tender, This

shall be applicable after Defect Liability Period of One year. Total -3Yrs.

C. Operation of Sewage Treatment Plant Charges for providing manpower for operation of

STP at site as per the terms and conditions of the tender . The charges shall be

applicable after handing over of the system.Including cost of operater, Periodical

checking of the plant, periodical testing of treated water with submission of reports,

oiling, greasing, routine and preventive maintenance of electrical Items, consumables,

chemicals, disposal of dried sludge as per direction of engineer in charge.

Total Time Period -3 Yrs.

Manpower : 3 Operator (8 Hour shift) and 1 Helper

F Rate include all cost of material,Labour and require machineries involved in the item.In all

operation describe above for complete above item.

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

G Estimate offer should be including Collection tank,Treated water tank and all civil work

finished with water proofing ,treatment as require,plastering ,colour work as per

GSPHC,Structure duly tested for leakproofing

,Plant room flooring ,Pump foundation etc.and related S.S/M.S/CI work such All items should

engineer incharge.

H Electrical Supply panel,Power and control cabling.

Electric Control Panel & Cables with automation, audio Visual alarm. (As per Venders design )

A) Power and control cabling between panel and electrical motors, instruments.

All power cables up to 4 mm2 will be of Copper Armoured conductor, whereas above

4 mm2 will be of Aluminium conductor. Perforated metallic Cable tray with supports will

be provided to lay the cables.

B) All instrument cables will be of Copper conductor.

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

I (C)SITC of CPRI approved makeI IP 66 with Double door Compartment type Electric control

panel mounted on the Stand for Semi automatic operation of pumps comprising incoming

MCBB, digital VAF meter switches, over load and under voltage protection devices, single

phase preventers, Reverse phase sequence, MCB and DOL /Stat Delta starter for each

motor, indicating Lamp etc, dry suction cut off, all complete. 1 No. Panel

comprising:

• Compartment type, with 2mm sheet metal for Outer body & door & 1.5 MM sheet metal for

partition.

• Cubical type

• Floor mounted with 1.5 feet height supporting legs with necessary foundation as per site

requirment

• Cable bottom/Top entry(As per Site Situation)

• All cables inside the panel will be of Copper conductor.

• Incoming power control switch.

• Ammeters voltmeters Frequency (VAF) phase indicating lamps,

• MCB and starters.

• 2 Nos. automatic level controllers for actuating raw effluent and Filter Feed pumps

J (D) Automation for Pump operation :

System to start manually/automatically at every start, the other pump shall cut in There shall

be audio visual alarm in case any pump/blower fails to starts// trip. Proper name

plates & marking will be provided on the panel doors.

Programmable Control System for the following logic:

i) System to start manually/automatically

ii) At every start, the other pump shall cut in

iii) Audio visual alarm in case any pump/Blower fails to starts.

iv) Both the pumps & Blowers will be in operational but with one remaining standby at any

particular moment.

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

K E) Local Push bottom.

F) Armored cabling from our panel to motor starters and earth pits (in civil).

G) Necessary earthing chamber(Civil Job)

H) Earthing to panel connectivity to 25 x 6 mm GI patti & Panel to motor/ Machine

connectivity 10 mmcopper wire.

Control panel to be designed for semi-auto operation of STP. (i.e. LLC based operation

for raw and filter). Pressure gauges will be provided on delivery main for pumps, blowers and

vessels. Agency shall complete the STP system and put in working order.No Extra payment

shall be done for electrical item mention in above description.

Mode of measurements & payments The rate shall be for a unit of one set.

NOTE :SCREEN CHAMBER,INLET TANK ,FILTER TANK (ALL Civil works ) SHOULD

BE PAID SEPERATELY UNDER ITEM NO

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

Preparing structural design of RCC Under Ground / Partially under ground / above high

ground level Reservoir of required capacity as per relevant I.S.s and constructing the

same,including excavation in all types of soil strata (including rock) including shoring strutting

if required, for loose soil / to protect from collapse due to near by traffic load, casting 100 mm

thick P.C.C. leveling course in M-15, Refilling the pit with proper soil and disposing of the

surplus stuff at all lead . Including cement plaster in CM 1:2 with approved water proofing

compound to inside and out side up to 300mm ground level water touching surface to

container. Including all types of labour and material charges of lowering, laying, erecting /

hosting and jointing of pipe assembly to inlet, outlet overflow, washout and bye pass

arrangement as per hydraulic design. Providing and fixing accessories like MS / GI Ladder, CI

Manhole frame and cover, water level indicator, adequate cowl type ventilators or lantern type

ventilator with stainless steel jail. B.B. Masonry chambers for valves. Providing and applying

three coats of cement paint / snowcem to the out side face of structure. It also includes

satisfactory water tightness test as per relevant I.S. code and painting name of scheme and

capacity on the tank as per direction of engineer in charge. List of Indian Standards for Design

of GSR / SUMP:- The structural design of GSR shall be in accordance with provisions relevant

I.Ss. (1) I.S. 3370 part I & II 2009 or latest revised (1.1) I.S. 3370 part III & IV 1965 or latest

revised (2) I.S. 456 – 2000 or latest revised. (3) I.S. 1893 – 2000 – 1984 or latest revised. (4) I.S.

875, Part – 1 to 3, 1987 or latest revised.

General specifications :

[1].Water depth in container shall be adopted as per data of tender. If water depth is not

specified the suitable water hydraulic requirement shall be adopted for capacity.

[2].Shape of container (in plan) specified by in data shall be adopted in absence circular shape

shall be adopted.

[3].Size shall be fixed as per availability of space (land area) at site / acceptable engineer in

[4].Effect of overlapping of pressure bulbs on soil due near by structure and proposed sump

should be considered.Care shall be taken that no damage should occur to

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

[5].nearby existing structure. Compensation shall be paid for the same by agency.

[6].The minimum concrete grade for RCC shall be M-30

[7].Fe 500 grade reinforcing bars confirming to I.S. 1786 / 1139 shall be considered in design.

CRS / TMT bars shall be provided. In saline atmosphere corrosion resistance stainless steel /

HCR rebar shall be provided. Any other steel can be used with approval of C.E./ in situation

of non availability in market without extra cost.

[8].Minimum size (or thickness) of various components shall be provided as per tender criteria

/ specifications in absence as per I.S./ Std. practice of G.W.S.S.B. Minimum dimensions

specified for various components in tender data / specifications shall be provided without fail.

[9].The safe bearing capacity (SBC) shall be referred from SBC test report. In absence of report

it shall be referred from data sheet. If poor soil is found / water table is met with during

excavation SBC shall be scientifically ascertained and design shall be revise. No extra shall be

paid for increase in quantity.

[10].DI pipes and special shall only be used if type is not specified in tender.

[11].The rate shall include cost of dewatering during excavation making all arrangement when

water table meets within depth.

[12].The structure shall be designed properly to resist uplift due to ground water table

specified in data or actual ground water table meets with during excavation. If GWT / Uplift

iswater table meets with during excavation. If GWT / Uplift is mentioned in tender and during

excavation it dose not meet 7.5% rate shall be reduced.

[13].SS pipes railing shall be provided when sump height is ≥ 1.5 meter above ground level

[14a].RCC staircase/RCC Steps should be provided from GL to sump top slab based on the

height of the GSR above/below the ground.

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

[14b].RCC Staircase with SS railing to be provided inside reservoir container. BB Masonry

staircabin to be provided to cover the same with MS safety door having locking arrangement

[15].Appearance of structure should be aesthetically good looking acceptable to authority.

[16].Any charge in size, shape, depth below GL, height above GL, water depth, F.B., size of

member etc can be permitted in exceptional case due to site condition or hydraulic design

requirement by C.E. No extra shall be paid for change.

[17].Any charge in data, dimensions, shape, water depth,reduction in size if permitted by

competent authority and if itreduction in size if permitted by competent authority and if it

reduces quantity then payment shall be reduced prorate.

[18].When capacity of GSR / Sump is > 20 lakh liters two or suitable compartments acceptable

to executive engineer shall be designed and provided.

[19].Agency shall engage qualified (at least graduate) consulting engineer for designing the

structure and he / she shall visit the site for guidance of work.

[20].75% part rate shall be payable for concrete, reinforcement and plastering items of

container until satisfactory hydraulic testing for water tightness is performed as per tender

condition. Till the work shall be treated as incomplete.

Above conditions / general specifications Sr. No. 1 to 20 are part and parcel of tender (contact)

and prevail over other

provisions in tender for below 1 to 5 differents capacity of Sumps for STP as per STP drawings

Screen Chamber -

18a 1000.00 Ltr 5.98 Rs. Five & Paise Ninety Eight Only

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

COLLECTION TANK

18b 50000.00 Ltr 5.98 Rs. Five & Paise Ninety Eight Only

Consrurting Manhole with RCC TOP SLAB IN 1:2:4 mix (1 cemente :2 corarse sand :4 graded

stone aggregate 20mm nominal size ) found . Concrete 1:3:6 ( 1 cement :3 corarse sand : 6 brick

bats 40 to 50mm size ) inside plastering 15mm thick with c.m 1:5 ( 1 cement : 5 corase sand )

finish with a floating coat of neat cement making channaels in cement concrete 1:2:4 ( 1cement

: 2 Coarse sand : 4 stone aggregate 20mm nominal size) finished smooth complete including

curing & testing (i) inside size 900mm x 1200mm including with 230mm thick wall of brick Rs. Sixteen Thousand Four Hundred

19 masonary using brick having crushing strenghth not less then 35 kg/Sqcm in c.m 1:5 for 2.00 No 16435.16

Thirty Five & Paise Sixteen Only

multipurpose pipe line ( B- type depth 1.50mt. for multipurpose line) Rate are also iclusive of

Provinding and fixing precast RCC cover

Providing & Laying ( to level or slopes ) and jointing reinforce concrete non pressure pipes I.S.

class NP 2 of the following internal diameter with collars & butt ends prepaid for collar joints

Rs. Six Hundred Seventy One &

20 including testin of joints. 300 mm dia pipe . 25.00 Rmt 671.32

Paise Thirty Two Only

Table: Size: (1.52 x 0.76 x 0.76)

Provinding and fixing 19mm thick plywood top table with fixing 25mm thick plywood (19mm

+ 6mm) patta of 300mm width fixed on bottom periphery .The plywood table top is laminated

on top and bottom.the front edges of the table top surface is to be covered with 12mm thick

teak wood bedding patty with melamine polish finish of approved shed.The Rate includes the

cost of fixing telescopic suspended metal keyboard with mouse tray. 38mm thick vertical legs

made from plywood with exterior side 1mm and interior side 0.8mm approved laminate.

Appron should be made from plywood with laminated finish as per detail drawing and CPU

Trolley should be supplied of metal powder coated. Footrest (0.75 x 0.37) should be from Rs. Sixteen Thousand Six Hundred

21 teakwood with melamine polish complete.Seperate Drawer unit box (0.65 x 0.41 x 0.43) to be 1.00 No 16622.62 Twenty Two & Paise Sixty Two

made from 19mm plywood with 1mm outside and 0.8mm inside laminate as well as approved Only

shade for Left or Right sidewith wooden bidding patti on nylon castors with handle,lock and

telescopic channel.Rate includes the cost of all materials and labour etc. complete as per detail

drawing and instruction of engineer-in charge.The necessary hardware fitting shall be as per

approved make list of GSPHCL.

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

Low Back Chair (Staff & Visitor ) (MODEL LIKE HOF OCT 173) Providing and supplying

Revolving synchro tilting mechanism based chair with gas lift for adjustable height and

medium curved back with seat and back PU moulded cushion with MS pipe frame structure

and white foam layer for seat and molded PU foam. White foam layer for back covered with

thick cloth and draped with cloth of approved shade. (min. of Rs.150/meter). 5 legged

revolving molded nylon chair base with good quality of PU castors with 2 years replacement Rs. Four Thousand Six Hundred

22 guarantee. The chair to have wide polyurethane arm rest of approved shape. Complete chair 7.00 No 4669.00

Sixty Nine Only

of chair should be as approved by engineer in-charge.

High Back Chair (MODEL LIKE HOF OCT 171) Providing and supplying Revolving synchro

tilting mechanism based chair with gas lift for adjustable height and medium curved back with

seat and back PU moulded cushion with MS pipe frame structure and white foam layer for

seat and molded PU foam. White foam layer for back covered with thick cloth and draped with

cloth of approved shade. (min. of Rs.150/meter). 5 legged revolving molded nylon chair base

with good quality of PU castors with 2 years replacement guarantee. The chair to have wide Rs. Seven Thousand Sixty One &

polyurethane arm rest of approved shape. Complete chair should be in suitable shape. Rates to Paise Eighty Six Only

engineer in-charge.

Conference Table

Providing and fixing 25mm (19mm+6mm) thick (plywood, interior grade/MDF/with post

forming laminated top in approved shed) with bottom 0.075m. 19mm ply patta for edge

thickness and edges should be cover with 1mm Outside & 0.8mm interier side approved

laminate with 38mm (19mm+19mm) thick vertical legs made by plywood with exterior side

with laminated finish and 8mm thick plain glass fixed in center of the apron area as per detail Rs. Six Thousand Nine Hundred

drawing, footrest should be from 19mm plywood with laminated finish in approved shade. Eighty & Paise Ninety One Only

Including all materials and labour, all edges should be laminated etc. complete as per detail

drawing and instruction of engineer in charge and Architect.

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

Providing and fixing eco-friendly light weight calcium silicate false ceiling tiles having Regular

edge & 15 mm Thick Densified edges on the Tile Periphery for Extra Strength The Light weight

calcium silicate ceiling tiles shall have, light reflection 85% non-combustible as per B.S. 476 part

IV, 100% humidity resistance and also having thermal conductivity0.043° w/m KC.for the best

thermal Insulation. The Light weight calcium Silicate tile shall be of approved texture Fine

fissured/Spintone/Cosmos having NRC value of 0.5 & Globe having NRC value of 0.75 NRC

or equivalent of size 595 X 595 mm to be laid on true horizontal level suspended inter locking

metal grid of hot dipped galvanized steel sections (galvanizing @120 grams per sqm including

both side) consisting of main 'T' runner suitably spaced at joints to get required length and size Rs. One Thousand Six Hundred

25 of 24X38mm made from 0.30 mm thick (minimum) sheet, 1200mm centre to centre, and cross 18.94 Smt 1657.57 Fifty Seven & Paise Fifty Seven

T' of size 24X28mm made out of 0.33mm (Minimum) sheet spaced 1200mm along spaced Only

between main 'T' at 600mm centre to centre to form a grid of 1200X600mm and secondary cross

'T' of length 600mm and size 24x28mm made of 0.30 mm thick (Minimum) sheet to be

interlocked at middle of the 1200X600mm panel to form grid of

size 600x600mm resting on periphery walls/partitions on a perimeter wall angle pre-coated

steel of size (24X24X3000mm made of 0.40mm thick (minimum) sheet with the help of rawl

plugs at 450mm centre to centre with 25mm long dry wall screws @ 230mm interval and laying

15mm thick Densified edges light weight calcium silicate ceiling tiles of approved texture (Fine

Fissured/Cosmos/Spintone) in the grid including, cutting/making opening for services like

diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required, Main 'T'

runners to be suspended from ceiling using G.J. slotted cleats of size 25X35X1.6mm fixed to

ceiling with 12.5mm dia and 50mm long dash fasteners, 4mm G.l. adjustable rods with

galvanized steel level clips of size 85X30X0.8mm, spaced at 1200mm centre to centre long main

'T' bottom exposed with 24mm of all T-sections shall be pre-painted with polyester baked

paint, for all heights, as Per specifications, drawings and as directed by engineer-in-charge.

Note:- Only calcium Silicate false ceiling area will be measured from wall to wall. No

deduction shall be made for exposed frames/opening (cutouts) having area less than 0.30sqm.

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

The calcium silicate ceiling tiles shall have NRC Value of 0.50 (Minimum) for

Finefissured/Spintone/Cosmos and 0.75 NRC for Globe, light reflection 85% noncombustible

as per B.S. 476 part-IV, 100% humidity resistance and also having thermal conductivity. 0.043"

w/m KC.for the best thermal Insulation.

Providing and fixing wall acoustical paneling with using CS65 and IC 91 framing directly to

the wall and then fixing 12.5 mm perforated board with the help of screw and using rock wool

of 60 kg density and 50 mm thick between framing and perforated sheet. Then fixing Ecotone

make Micro polyester tiles acoustic wall paneling with the specification of 50MM thick having

density of 180 kg/m3 with NRC value of 0.80 surface matt finish which is fixed with solution Rs. Four Thousand Six Hundred

26 SR665 as required. The panel should have euro class B ASTM E84-13 fire rating. The color 67.00 Smt 4628.75 Twenty Eight & Paise Seventy Five

shade of Panel as approved by Architect. Including all accessories, material & labor complete Only

as directed by Engineer.

Providing, Supplying and Fixing 16MM thick HDF Board of Approved Brand. The rate

inclusive with labours, Adhesive,Cutting and Fixing As per drawing and as Directed by Rs. One Thousand Ninety Six &

engineer-in-charge. Paise Fifteen Only

Civil Amount

Providing & erecting Point wiring with 1.1 KV grade ISI marked 2 X 1.5 sq. mm copper PVC

insulted FRLS wire with 1.5 sq. mm (green) copper PVC insulated FRLS wire for earth

continuity in FIA approved ISI mark medium class white colour 20/25 mm dia. embossed

rigid PVC pipe with PVC fitting fixed with adhesive solution erected on/in Brick Wall / slab

along with continuous G.I. fish wire to draw wires and laid in approved manner zari for PVC

pipe and boxes shall be filled with cement mortar and finishing the surface to match the wall /

ceiling complete with approved make 5/6 Amp. ISI make modular type switch and accessories

mounted in 20 G. G.I. company fabricated metallic box covered with appropriate front plate Rupees Four Hundred Sixty One

28A 8.00 Point 461.00

modules erected flushed with wall / ceiling with necessary modular lamp holder / modular Only

ceiling rose / HD Connector as directed..(Deep Junction box 75mm depth if required)(Make &

Model approved by EIC and matching colour with switch and accessories) for concealed

wiring. Light point. Cat.-II

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

Necessary sheet / tape / polythene / sand must be erected or filled in all box to prevent

mortar going into the box. Length of point wiring must not increase than 10 mtr. For that

necessary switch boards and their locations must be finalised before execution by agency

otherwise payment will not be done for extra long point. (For future extention, if required,

agency has to erect one higher size metal box and modular plate as per instruction of EIC. Cost

of blank plate shall be paid as per tender item) [This item include cleaning (inside/outside) of Rupees Nil

all G.I. switch boards, electric point box, fan box, MCBDB & box cutting plaster finishing for

modular plate without any gap]

For Fan Point (with 6 A. Modular type switch and two module hum free EME Five step type

Rupees Six Hundred Forty Eight

28B Electronic fan regulator both having ISI mark) Cat.-Il. 2.00 Point 648.00

For separate Point (with 6 Amp. Switch & 3/5 pin socket both having ISI mark) Cat.-Il

Rupees Four Hundred Eighty Nine

28C 2.00 Point 489.00

For Looped on switch board (with 6 Amp. Switch & 3/5 pin socket both having ISI mark) Cat.-

Rupees Two Hundred Thirty Four

28D Il 4.00 Point 234.00

Providing and erecting Medium Class FIA approved and ISI mark white colour (embossed)

RIGID PVC PIPES of following size complete erected with necessary PVC fittings & Junction

boxes fixed with adhesive solution & clamps on / in wall / ceiling along with continuous fish

29A wire to draw mains with necessary fittings and junction boxes for following dia. (a) 20 mm. 120.00 Mtr. 24.00 Rupees Twenty Four Only

25 mm dia.

29B 90.00 Mtr. 33.00 Rupees Thirty Three Only

For 32 mm dia

29C 50.00 Mtr. 54.00 Rupees Fifty Four Only

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

Providing and laying Mains with FRLS PVC Insulated wire ISI marked 1.1 KV grade with FIA

approved ISI mark medium class 20/25/32 mm dia. embossed rigid PVC pipe with PVC

fitting fixed with adhesive solution to be erected on/in brick wall / slab along with continuous

G. I. fish wire to draw mains laid in approved manner with plastering by cement mortar &

finishing the surface to match the wall / ceiling complete with FRLS PVC insulated wire for

30A earth continuity. (Approved ISI make only) [a] 2 x 1.5 sq.mm. FRLS copper multi stranded 80.00 Mtr. 62.00 Rupees Sixty Two Only

conductor mains with 1.5 sq.mm. FRLS copper multi stranded conductor for earthing as per

standard colour code. [conductor resistance should be as per IS:8130/1984]

For 2 x 2.5 sq.mm. FRLS copper multi stranded conductor mains with 1.5 sq.mm. FRLS copper

multi stranded conductor for earthing as per standard colour code. [Wire must be having box

30B 50.00 Mtr. 82.00 Rupees Eighty Two Only

2 x 6.0 sq.mm. FRLS copper multi stranded conductor mains with 2.5 sq.mm. FRLS copper

multi stranded conductor for earthing as per standard colour code. [conductor resistance

Rupees One Hundred Forty Six

30C should be as per IS:8130/1984] 90.00 Mtr. 146.00

Providing & fixing 20mm. dia. PVC insulated G.I. corrugated Flexible pipe with necessary

socket, PVC bushes saddle, Check-nuts etc. complete of following sizes.

31 30.00 Mtr. 31.00 Rupees Thirty One Only

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

Providing and fixing Plug Point wiring with 1.1 KV grade ISI marked approved make 2 x

sq.mm copper PVC insulated FRLS wire with 1.5 sq.mm (green) copper PVC insulated FRLS

wire for earth continuity in FIA approved ISI mark white colour medium class 20/25 mm

dia. embossed rigid PVC pipe with PVC fitting fixed with adhesive solution erected in

wall/slab along with continuous G. I. fish wire to draw wires and laid in approved manner

zari for PVC pipe & boxes shall be filled with cement mortar & finishing the surface to match

the wall / ceiling complete with 16 Amp Modular type Swich and accessories mounted in

G. GI company fabricated metallic box covered with appropriate front plate modules erected Rupees Seven Hundred Twelve

32 2.00 Point 712.00

flushed with wall. (a) 16 Amp. Indicator switch & 1 No. 6/16 A universal socket white colour Only

suitable for 3 pin top duly both having ISI mark. (Necessary sheet / tape / polythene / sand

must be erected or filled in all box To Prevent Mortor Going In To The Box) Cat.-II

Providing & Erecting 2.0 mtr long Earthing system by making minimum bore of 225 mm dia

in soft soil. Suitable for doing pipe-in-pipe technology earthing.Earthing electric rod must be

made from Corrosion free Hot dip galvanizing pipes having following specification.

(A) Earthing Electrode: outerpipe:- 88 mm minimum O.D., ISI 'B ' Class ISI mark of Reputed

Brand, Inner pipe:- 42 mm minimum O.D., Pipe B Class ISI mark reputed Brand Terminal

Size: 70mm X 100mm length, Terminal Should be made from inner pipe for that pipe must be

pressed and gave rectangular shape so its work as a terminal.The hot deep galvanising must

be done after above process.Galvanised thickness must be minimum 75 micron any where. SS

Nut bolt:- 2 no.with washer suitable for 14mm dia. hole must be provided at terminal. total

minimum Weight(approx.) of earth electrodewith inside conductive material minimum

should be 26 kg. Rupees Seven Thousand Twenty

33 (B) Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm/meter testing as per IEC 62561- 4.00 Each 7025.00

2017, Voltage drop:- < 1 volt at no load & dry form, Sulphar content:- <2%

(C) Back fill Compound:- Earthing compound should be capable to retain moisture for long

time Back Filling Compound weight is 25 Kg.

(D) Chamber and cover:- Earthing chamber should be size of 400 mm X 400 mm X 400 mm

depth and Cover should be heavy duty cast iron with required size of 300 mm X 300 mm X

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

Necessary test report must be submitted.

1. Short circuit test by ERDA/ CPRI for 25KA

2. Resistivity test of conducting material from NABL accredited lab.

3. Hot dip galvanised / zinc coating micro test from reputed laboratory.

4. General test report from OEM regarding specification of earthing.

[Make and model approved by EIC Strictly subject to item specification only] [OEM has to

submit all detail & sample for approved before supplying] Rupees Nil

[Water must be poured in bore before starting earthing. Earthing value must be measured with

earth tester. Agency has to bring the earth resistance to at least 02 ohms & voltage between

neutral & Earthing upto 02 volt. Agency has to maintain earthing & its value for one year.

Earthing must be done in the presence of A.E. (GSPHCL)]

For above earthing additional charges for boring in hard rock soil (by breaker) & filling soft

soil in earth pit (certificate for soil have to given by DEE / AE along with photographs) Rupees Two Hundred Seventy Six

Supplying & erecting approved make SMC press moulded composite FRP. loop-in, loop-out

approx. 2mm thick box complete with Bakelite connector strip 5way(3P+N+E),DIN rail for

mounting mob & hinged doors as per requirement having locking arrangements with

35 mounting clamp with nuts, bolts & washers suitable for erection on pole with cable clamps& 2.00 Each 890.00 Rupees Eight Hundred Ninety Only

earth bolt of following size of box.(A) 300mm x 200mm x 100mm [deep]

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

Supplying and Erecting LED indoor fitting of approximately 4feet long with LED of wattage 0.2W to

0.5W assemble on single MCPCB with housing use as a heat sink shall be made from Aluminum

extrusion having enough strength (sample must be

approved by EIC) with polycarbonate diffuser with following specification:(A) Company mark/name on the

(B) Rated input voltage and frequency: 220V to 240 VAC ; 50Hz.

(C) Rated input wattage: max. 24w

(D) Rated input current : 0.2 Amp

(E) Power Factor : Min.

(F) ATHD : Max. 15%

(G) Rated Luminous flux: Min. 2420 lm

(H) CCT: 6500K

(I) CRI: Min. 80Ra Rupees Three Hundred Seventy

36 (J) Driver Efficiency: Min. 80% 4.00 Each 370.00

(K) LED life span: Min. 50000 Hrs @ L70

(L) Over Voltage protection: Withstand up to 440V/AC for 4 Hrs.

(M)Surge protection : Min. 2KV

(N) IP rating: IP

(O) IK rating : IK

(P) Short circuit , Open circuit & Reverse Polarity Protection must be provided

(Q) Fixing clamp design & strength should be sufficient to hold the fitting erected on wall or ceiling.

(R) 3 core copper wire of appropriate size with earthing connector(Note:-The manufacturer/ authorized Channel

partner of the manufacturer has to

submit 5 yrs free replacement Guarantee for complete Fixture) [Approval will be given strictly subject to

item specification]

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

Providing, erecting, testing Ceiling Fan confirming to IS: 374/1979 AMDT No. 1 to 6 Class-I,

50 Hz. Specification of Ceiling Fan must be as per below. (1) Sweep: 1200 mm, (2) Operating

Voltage: 180 to 230 V, (3) Power Factor: > 0.9, (4) Power Consumption: maximum 53W, (5)

RPM: minimum 330, (6) Service value:min 4.3 m3/min. (7) Class of insulation: 'B', (8) No. of

heavy duty premium quality Ball bearing: Two, (9) Total Body: Top & Bottom should be

alluminium, (10) Blade: Aluminium approx 1.1 mm thick, (11) Colour: White high grade

powder coating, (12) Canopy: Two Nos. Heavy duty, (13) Condenser: min 1.5 MFD (15%

Tolerance )as per is 1709-1984, Aluminium body premium quality, Branded make,(14) Down

road: up to 1.0 mtr as per site requirment, (15) Required fixing accessories, (16) 3 core Rupees One Thousand Nine

0.75 sq.mm ISI wire as per site requirment, (17) No vibration and noise due to mechanical Hundred Twenty Nine Only

parts. (Agency has to erect safey wire with ceiling fan and checked with EIC) (OEM has to

approved model as per tender specification and tested at ERDA) (Necessary test reports

should be submitted strictly at the time of approval. Sample approved by EIC subject to above

specification only)

Supplying and erecting 8 W LED lamps with following wattage capacity of 220 to 240 voltage,

minimum 15000 burning hours life, 500 V in built-surge protection,Polycarbonate diffuser,

mounting suitable for E14 / E27 / B22 lamp holders, pf >= 0.5 (A) LED Lamps integral type,

38 2.00 Each 111.00 Rupees One Hundred Eleven Only

with PC diffuser suitable LAMP holder

Providing and erecting Polycarbonate body surface mounting LED Bulk head type 9 watt

Lighting Fitting with electronic driver having THD < 15%, CRI>80, P.F.0.95 And lumen

output from luminaire 720 lm, input voltage range 90-300 V AC, 50 Hz cool white (3000 to

39 k), inbuilt driver having efficiency >=80lm/w, -20 deg C to + 60 deg C working temperature, 2.00 Each 780.00 Rupees Seven Hundred Eighty Only

AL frame with Beam Angle 120 deg.

Supplying & Erecting Fan Hook Of 10 mm M.S Round bar bounded to the RCC bars up to

mm Length each side & piereced through 18 Gauge G.I Box having 125 mm dia depth of

Rupees One Hundred Twenty Five

40 mm complete erected concealed in ceiling with necessary modular plate / sheet. 6.00 Each 125.00

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

Providing & erecting weather proof, dust & vermin proof, floor mounted front operated indoor

type cubical panel board having IP-42 & above protection as per approval from engineer

incharge and made from 2 mm. thick CRCA sheet for outer body & doors, 1.6 mm. thick CRCA

sheet for internal partitions with necessary supporting angles, flats including skirting, bending,

drilling, welding, riveting with internal partitions & cable alley as per requirements &

instruction of engineer-In-Charge with erection of supplied switchgears, busbars with suitable

size of interconnecting PVC copper wire / Copper-Aluminium strips, rubber gromets, rib, Rupees Sixteen Thousand Two

41 1.50 Sq. Mtr. 16230.00

control wires, backelite control fuses, measuring instruments, earth bus & earth bolts, Hundred Thirty Only

foundation flange-bolts-base plates, sufficient nos. of hinged doors, handle with locking

arrangement, rubber gasket complete with Required Nos. heavy Duty Connector with

Cadmium plated nut and bolt for Anti rusting

The panel shall be supplied with Seven Tank chemical process which shall be carried out

before applying painting, painted with powder coating. (The rates excludes the cost of

switchgears, busbars, interconnecting mains & Copper / Aluminium strip, fuse, meters etc.

The dimension shall be measured excluding base beams) The standard companies switch gear

shall be used and only manufacturers at CPRI approved factory as per IEC 61439 and shall be Rupees Nil

certified by that company whose switch gears are used after fabrication for beneficial use. With

350 mm depth

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

Panel manufacturer have to give 3 years maintenance and service support if in case of

breakdown or fault. Panel manufacturer have to submit electrical meter calibration report.

Agency should design the panel in such a way that there should not be any excess in panel

area (sq.mtr) & length of bus-bar (mtr), if any excess occurs draw attention to GSPHCL at the

time of approval of G.A. drawing.

Loading and unloading of above item shall be done by hydra and skill work force under

supervision of electrical engineer and guidelines given by manufacturer to avoid damage to

the item. Picture of it to be submitted in running bill / final bill.

Size of door and Ele. room / Pump room shall be checked by agency's engineer before giving

order. If found any problem in size discuss with GSPHCL engineer for rectification before Rupees Nil

giving order. [Including Necessary numbering / marking on PANEL done with red colour

radium sticker as per site requirement and instructions given by EIC on site. Font / number

size given by EIC on site as per requirement] (All Panel as per IEC 61439 as per NBC

Guideline) [Manufacturer must be of Gujarat state so three stage inspection can be done]

Providing and erecting Approved make Four pole moulded case circuit breaker having

breaking capacity ICU of 35 K.A. at 415 V having normal current rating of 125 A. with

variable/Fixed thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all

Rupees Seven Thousand Nine

42 internal connections, spreader tinned copper & complete erected in existing 16 G.M.S. housing. 1.00 Each 7976.00

Hundred Seventy Six Only

ICS=100% of ICU only.

Providing and erecting Approved make Four pole moulded case circuit breaker having

breaking capacity ICU of 25 K.A. at 415 V, having normal current rating up to 25 A to 100 A.

with variable/Fixed thermal & magnetic release suitable to work on A.C. supply 50 c/s. with

Rupees Six Thousand One Hundred

43 all internal connections, spreader tinned copper & complete erected in existing 16 G.M.S. 4.00 Each 6112.00

Twelve Only

housing. ICS=100% of ICU only

Supplying & Erecting Approved Make Extended operating rotary handle with pad lock with

three position Trip, Off, On suitable for 25 Amp. to 250 Amp. panel mounting.(Company Rupees Eight Hundred Sixty Five

Must be same company of switchgear) Only

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

Supplying and erecting tripple pole & neutral 440V / 500 V Panel mounting Copper Busbars

with four equal Nos. of electrolyte bus having current density not more than 1.6 Amp. /

sq.mm (Rated current / cross section area) duly wraped with colour insulating tape for phase

sequence of following current carrying capacity, erected with necessary bus bar supports /

Rupees Three Thousand One

45 insulators, main cable socket to each bar, erected in existing cubical panel with necessary 2.00 Rn.Mtr 3171.00

Hundred Seventy One Only

connections.For electrolyte copper busbars suitable for 200 Amp. capacity

Supplying and erecting Approved make Earth fault Relay suitable to mount with inter

connection to moulded case circuit breaker having CT ratio & MCCB rating as following along

with shunt trip 220 V AC with all internal connections & complete erected in existing

Rupees Four Thousand Nine

46 M.S.housing.(2) 125 A - 200 A, CT Ratio 1/200 [make and model approved by EIC strictly as 1.00 Each 4934.00

Hundred Thirty Four Only

per tender specification]

Supplying and erecting approved make panel mounting type Digital Voltmeter having 3 x

1/2 digits LED display, 0 to 750 AC Volts range having 0.5 class accuracy erected on existing

panel board with all connection, wiring etc. with manufacturers calibration certificate. [make Rupees One Thousand Two

and model approved by EIC strictly as per tender specification] Hundred Sixty Three Only

Supplying and erecting approved make panel mounting type Digital Ammeter having

digits LED display, external CT operated, calibrated for 0 to 1000 Amps. suitable to operate on

500 Volt AC, having 0.5 class accuracy erected on existing panel board with all connection,

Rupees One Thousand Five

48 wiring etc. with manufacturers calibration certificate. [make and model approved by EIC 1.00 Each 1543.00

Hundred Forty Three Only

strictly as per tender specification]

existing panel board with necessary connections. [make and model approved by EIC strictly as Rupees Three Hundred Fourteen

per tender specification] Only

Supplying and erecting approved make suitable panel indicator LED type lamp, lens cover,

50 complete erected with necessary connections. 3.00 Each 43.00 Rupees Forty Three Only

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

Providing and Erecting of Miniature circuit breaker single pole 6 Amp. to 25 Amp. suitable

to operate on 240 V A.C. system and having breaking capacity 10 KA to be erected in existing

51 box. confirming to IS 8828/1996 with ISI Mark. 3.00 Each 111.00 Rupees One Hundred Eleven Only

Providing & erecting L.T. Current Transformer with bar primary 50/5 to 1000/5 ratio 15 VA

burden having 0.5 class accuracy erected in existing CRCA box duly secured with insulating

Rupees Two Hundred Seventy Two

52 materials connected to the meter [make and model approved by EIC strictly as per tender 3.00 Each 272.00

specification]

Providing & erecting 240 V MCB Double pole switch for Motor & Inductive load (C curve)

having 10 KA breaking capacity & confirms to IS:8828 in Existing M.S. box having following Rupees Three Hundred Twenty

capacity. For 40 Amp. Seven Only

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having

10KA breaking capacity & confirms to IS :8828 in existing box having following capacity [c]

54 2.00 Each 730.00 Rupees Seven Hundred Thirty Only

Supply, Installation, Testing & Commissioning of Three Phase, 440 V Surge Suppressor

protection Device (SPD) & 40 Amp TPN MCB (or As per SPD OEM guide line for the

protection of SPD which is erected such a way that it can be operated easily) SPD must be

capable to protect all electrical and electronics equipments if SPD blast or fuse then the panel

Rupees Six Thousand Three

55 builder must have replace it soon during defect liability period.The Detail Specification of SPD 1.00 Each 6319.00

Hundred Nineteen Only

are As per Attached sheet with Annexture -A(E). (Hakel,ikra,OBBO make) (With Three year

Gaurantee/warranty)

Providing, erecting, Fabricating the M.S. structure as per requirement of site as per structure

design Including proper size approved by EIC of M.S. angles, flats, bars, square pipe,

channels, sections (Tata, Jindal, Asian, JSI Make) complete with cutting, welding, grinding and

finishing duly painted with Asian/Nerolac make premium quality oil paint and true care red

oxide metal primer,asian paint make with erection on site as per direction of engineer in charge Rupees Seventy Five And Paise

56 with necessary grouting cementing, plastering and finishing complete. All hole opening of 60.00 Kg. 75.20

Twenty Only

square pipe end must be closed with M.S plate welding. Payment will be done on KG as per

Actual weight.

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

Supplying & erecting 12 mm thick backelite sheet of approved make and grade on existing

x 25 x 3 mm red oxide painted angle iron frame suitable for fixing ICDP SWITCH and energy

meter (contractor shall make approved drawing of Bakelite sheet To arrange required No. of

Energy meter & ICDP/MCB switch-busbar etc. as per Actual space available in electrical room Rupees Two Thousand Two

57 1.00 Sq. Mtr. 2289.00

at site) Hundred Eighty Nine Only

Providing and erecting metalic danger notice board for MEDIUM VOLTAGE installation to be

58 erected as per I.S. 2.00 No. 69.00 Rupees Sixty Nine Only

Providing and erecting approved make single phase Double Door metal clad D.B. as per relevant

indian standards ammended upto date. Supplying and fixing following way single phase MCB

distrubution board of company fabricated with sheet box with powder coated inside and outside after

apply seven tank chemical process of CRCA sheet (MCBDB Door, Backside & Body must be made of

1.2 mm thick CRCA sheet )cover complete with suitable integral single piece construction tinned

copper busbar and link with all necessary interconnection and with necessary size MS frame for

mounting MCBDB. Manufacturer must be provided (1) IP 43 and as per IS:8623-1 & 3, IEC 61439-1 &

having D type PU gasket. (2) Seven tank Powder coating Certificate (3) Tinned Copper/Brass make

neutral & Earthing link with isolation & Protecting Cover for 240 Volts on surface / recess complete

with loose wire box, terminal connectors for all incoming and outging circuits, with suitable size FRLS

PVC insulated copper conductor up to terminal blocks and internal connection, tinned coppper bus

bar, 1 no. tinned copper neutral link, tinned copper earth bar, din bar, detachable gland plate,

interconnections, powder painted including earthing etc. Single phase incoming and horizontal single

phase outgoing. For 16 Way MCBDB: Including 40 Amp. 30 mA double pole ELCB (ELCB Rupees Five Thousand Eight

confirming to IS:12640/1988 having sensitivity of 30 mA and breaking capacity of 10 KA), MCB 40 Hundred Sixty Nine Only

Amp. double pole switch (C curve confirms to IS:8828 having breaking capacity of 10 KA) and S.P.

MCB of rating 6 to 32 Amp. with NL suitable to operate on 240 Volt A.C. power. (6/25 Amp sp mcb

company of MCB / ELCB to be used) (MCBDB must be erected in line & level with spirit level and

finish the external edge with box cutting plaster) (Same colour MCB(SP/DP) should be used as

same as MCBDB) [Including Necessary numbering / marking on box done with red colour radium

sticker as per site requirement and instructions given by EIC on site. Font / number size given by

EIC on site as per requirement]

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having

10KA breaking capacity & confirms to IS:8828 with same company metal box with earthing

Rupees One Thousand One

60 terminal having following capacity with necessary Numbering / marking with oil Paint by 1.00 Each 1172.00

Hundred Seventy Two Only

painter. [c] 63 Amp.

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having

10KA breaking capacity & confirms to IS :8828 with same company metal box with earthing

Rupees One Thousand One

61 terminal having following capacity with necessary numbering/marking with oil paint by 1.00 Each 1104.00

Hundred Four Only

painter. For 40 Amp.

Providing and laying Mains with ISI marked, 1.1 KV grade electrolyte multi stranded,

annealed copper conductor with heat resistant PVC insulated conforms to IS:694, IEC -

erected in existing pipe of following size (Specifically for control panel, relays, power Rupees One Hundred Forty One

62A 60.00 Each 141.00

switchgears, motor starters & control wiring) with required size of copper lugs, nuts and bolts Only

if required. [g] One wire 16.00 sq. mm [For Earthing]

62B For One wire 10.00 sq. mm 60.00 Mtr. 91.00 Rupees Ninety One Only

For One Wire 25 sq.mm wire Rupees Two Hundred Thirty Four

Supplying and erecting approved make single phase servo controlled voltage stabilizer

suitable for input voltage range 180/250 V And output voltage range 225/235V. A.C. Rupees Six Thousand Three

complete erected. (a) 1.0 KVA Single Phase. Hundred Ninety One Only

Providing & erecting XLPE (IS : 7098) (I)-88 ISI marked armoured Aluminium conductor cable

for 1100 volt to be laid 90 cms. Under ground or to be laid on wall with 1.00 m.m thick G.I.

Rupees Two Hundred Eighty Two

64 heavy guage cable clamp or in existing DWC pipe underground or road crossing or floor . 50.00 Mtr. 282.00

(C) 3 1/2 core 50 Sq. mm (25 Sq. mm 1/2 core)

Providing & erecting XLPE (IS : 7098) (I)-88 ISI marked armoured Copper cable for 1100 volt to

be laid 90 cms. Under ground or to be laid on wall with suitable G.I. heavy guage 1.0mm thick

Rupees Two Hundred Sixty Nine

65A cable clamp or in existing DWC pipe underground or road crossing or floor. (a) For 4 core x 30.00 Mtr. 269.00

For 4 core x 4 sq.mm. Rupees Three Hundred Sixty One

For 4 core x 10 sq.mm

65C 20.00 Mtr. 670.00 Rupees Six Hundred Seventy Only

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

Providing & laying HDPE Double walled corrugated pipes (DWC) (conforming to IS:

(part 24) 2018)) with minimum load required of 450N capacity with anti rodent and ultra violet

material properties with necessary connecting accessories of same material at required depth

to be laid 90 cms. under ground for laying of cable below ground / road surface for enclosing Rupees One Hundred Seventeen

cable and back filling the same to make ground as per original. (A) For Outer dia. 50 mm and Only

Inner dia. 38 mm. ) (Test Certificate to be Submitted)

66B (C) For Outer dia. 90 mm (Test Certificate to be Submitted) 30.00 Mtr. 150.00 Rupees One Hundred Fifty Only

Providing & erecting Flexible PVC insulated multistrand multicore 1.1 kv grade ISI marked

copper wires of following size to be erected as directed. 3 core x 1.5 sq.mm. PVC insulated

67 20.00 Mtr. 46.00 Rupees Forty Six Only

round copper wire ISI mark.

Supplying & Erecting following size of Light duty “A” Class G.I. Pipe & erecting as directed

Rupees One Hundred Seventy One

68 by Engineer-in-charge. For 25 mm dia. 10.00 Mtr. 171.00

Providing & fixing double compressed heavy duty flange type brass cable gland with rubber

ring for P V C insulated armoured cable complete with outgoing tails, insulating tape etc. For

69A following size cables. For 2 to 4 core x 4.0/ 6.0 Sq. mm (Sigma, MCI, Comet Make Only) 8.00 Each 43.00 Rupees Forty Three Only

For 2 to 4 core x 10.0 Sq. mm (Sigma, MCI, Comet, Make Only)

69B 4.00 Each 48.00 Rupees Forty Eight Only

For 3*1/2core*50 Sq. mm (Sigma, MCI, Comet Make Only)

69C 4.00 Each 75.00 Rupees Seventy Five Only

Supplying and erecting approved make Octagonal pole made from HR sheet steel. The pole

should be made as per IS. and shall be coated with hot dip galvanizing as per IS

2629/2633/4759, suitable suspend local wind speed with integral Junction box with Hot

Deep Galvanised door having 2 nos. 180° operated hinges & 2 nos. Ln key locking with

silicon rubber gasket. Consist of terminal plate of min 6mm Hylam sheet, standard profile

35 mm X 7.5 mm Din-Rail & MCB, Brass stud type terminal and arrangement for cable

Rupees Eleven Thousand Four

70 termination to be erected on RCC foundation as per details given by manufacturer and EIC 2.00 Each 11410.00

Hundred Ten Only

considering site requirement.

Foundation Details: (1) Grade of RCC 1:2:4, (2) Grade of steel rainforcement of RCC FE 415, (3)

Clear cover to rainforcement 50mm, (4) Concrete vibrated, (5) use suttering / farma, (6) Hot

deep galvanized average 70 Micron, (7) Detail drawing will be given by corporation

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

(C) 7 Mtr. Long 70 mm Top X 135 mm bottom dia, 3 mm thickness with 225 mm X 225 mm X

16 mm base plate, 4-M20 Bolts and 600 mm long hot deep galvanized J-Bolt, nuts, washers

with 800 mm under ground and 200 mm above ground level and Foundation in 1:2:4

proportion as per details given by manufacturer and EIC considering site requirement. Rupees Nil

Approx Pole weight 67 kg.(Make:- Bajaj, Valmont, Transrail, Ambica Only) (Test certificate

to be submitted)

Providing & erecting bracket consisting of ISI mark "B" class G.I. Pipe 4.2 cm outside diameter

complete with suitable G.I. Sleeve tubing of 2 mm. thick and required size and length suitable

for 76.5 / 80 mm. required size of pole top or pipe in pipe surface for terrace as per instruction

of EIC or wall bracket as per instruction of EIC having nuts and bolts for fixing the brackets

and having spread of Upto 0.70 mtr. length with suitable rise as per site condition and suitable

welded stiffner reducer and nipple with check nut complete painted with one coat of yellow Rupees Four Hundred Eighty Seven

zinc and two coats of alluminium paint for Single arm bracket suitable for pole or terrace as Only

per design given by EIC (a) For single arm bracket. (Jindal / Asian / Tata / Surya Prakash

make Only) (Fabricators:- Bajaj, valmont, Transrail, Ambica Only) (Test certificate to be

submitted)

Supplying and erecting Fabricating terminal box for street light pole made from 16 SWG M.S.

sheet having following size complete with fixing arrangement for terminal board, with

necessary hole for wire entry and exit from the box. The box shall be provided with cover and

hinges on one side and bolting at other end The box shall be fixed by clamps fabricated from

25mm x 6mm flat.The box shall be painted with one coat of red oxide and two coats of paint

72 having following box size 330 mm x 260 mm x 140 mm (depth). Providing and fixing Terminal 3.00 Each 702.00 Rupees Seven Hundred Two Only

board of size 5.0 x 127 x 152.4 mm.bakelite sheet with 15 Amp. kitkat pattern porcelain fuse

unit with suitable brass studs with nuts, washers and clamps of size 25 mm x 3 mm suitable for

pole painted with one coat of red lead paint.

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

SITC of Outdoor aesthetically designed LED Street Light Luminaire with total consumption of

Max. 45 W with single piece die cast aluminium housing, high power LED shall be mounted

on high quality metal core PCB with extremely precison designed heat sink complete with

IP66 protection Class with polycarbonate / thoughened glass cover the fixture should be

suitable for pole/bracket mounting. The fixture to comply both LM79 and LM 80 guidelines

with LED module min. 130 lumen/watt with toughen Glass L70 at 50,000 hrs, provided with

high quality polycarbonate lenses for better light distribution. The Fixture Should be able to be

Pole Mounted and also bracket mounted, provided with high quality driver for protection Rupees Three Thousand Five

against high and low Voltage cut Off, opertional for high amibient and high humid Hundred Twelve Only

envirnoments, THD of driver should be less than 10% and P.F > 0.95. Also the Fixture should

meet the following technical criterias Oprating range Voltage 160 to 270 V, system efficiency

>= 110 lm/w, and total lumens not less then 4950, CCT > 5000K, CRI > 65, beam angle 120 deg,

surge immunity level at least 4 KV integral and 10 KV non integral

The Separate Potted driver should have over current, over voltage protection, short circuit

protection so that the fixture recovers once the fault is removed. In addition to the above

product should be operational in the temperature range of 0 deg to 50 deg and humidity range

of 10% to 90% RH.The watt capacity of each LED Should be gereter than equal to 5Watt (Note:- Rupees Nil

The manufacturer / authorized Channel partner of the manufacturer has to submit 5 yrs free

replcement Guarantee for complete Fixture)

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

SITC of Outdoor aesthetically designed LED Flood Light Luminaire with total consumption of

maximum 90 W with single piece die cast aluminium housing, LED's mounted on high quality

metal core based PCB with extremely precison designed heat sink, complete with IP66

protection Class, with polycarbonate / Toughened glass cover. The fixture should be suitable

for pole/bracket mounting. The fixture to comply both LM79 and LM 80 guidelines with LED

minimum 130 lumen/watt with L70 at 50,000 hrs, provided with high quality polycarbonate

Seperate lenses for better light distribution. The Fixture Should be able to be Pole Mounted

and also bracket mounted, provided with high quality potted driver for protection against,

high and low Voltage cut Off, opertional for high amibient and high humid envirnoments,

THD of driver should be less than 10% and P.F > 0.95. Also the Fixture should meet the Rupees Six Thousand Two Hundred

following technical criterias. Operating range Voltage 160 to 270V, system efficiency > 110 Twenty Eight Only

lm/w, CCT > 5000K, CRI >65, beam angle 120 deg, 4kV integral & non integral surge

immunity level at least 10 KV non integral... Flood Light lumens shall be more than

(Note:- The manufacturer / authorized Channel partner of the manufacturer has to submit

5yrs free replcement Guarantee for complete Fixture) (Provision in Estimate For Garden)

Providing & fixing Solderless crimping type Copper lugs conforming to IS suitable for cable

of following size evenly crimped with high pressure tool & connected to switchgear terminals

75A with brass/cadmium plated nut bolts in an approved manner. [a] 1.5/2.5 to 6 Sq.mm 50.00 Each 8.00 Rupees Eight Only

75B (B) 10 Sq.mm 16.00 Each 10.00 Rupees Ten Only

Providing & fixing Solderless crimping type Aluminium lugs conforming to IS suitable for

cable of following size evenly crimped with high pressure tool & connected to switchgear

76A terminals with brass/cadmium plated nut bolts in an approved manner. [d] 50 Sq.mm. 12.00 Each 20.00 Rupees Twenty Only

76B (C) 16/25 Sq.mm. 4.00 Each 15.00 Rupees Fifteen Only

Providing & Erecting Universal Astro 5 KVA intelligent streetlight control system insu with

weather proof box for outdoor application. (As per specification attached separately) (Make Rupees Twelve Thousand Eight

and model approved by EIC) Hundred Ninety Five Only

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

Supplying and erecting Servo Controlled Voltage Stabilizer (SCVS) as per following

requirement: (1) Input Voltage Range - Three Phase 340 To 480 Volt AC. (2) Out put Volatge -

Three Phase 415 Volt AC (Line - Line) with Voltage Regulation of +/- 1%. (3) Frequency range -

47 Hz To 63 Hz. (4) Efficiency - More or equal to 98%. (5) Type of Stabilizer - Suitable for

Balance & Unbalance Load and Voltage including SPD (6) Controlled Type - Digital Micro

Controller Based Disply. (7) Rate Of Correction - Upto 100 Volt / Sec (Line - Line) (8) Servo

Motor Drive - AC Syncronous Stepper Motor - As per KVA Capacityy, Out put volatge and

Voltage regulation requirement. (9) Nil Wave form Distortion and Effect of Load POwer. (10) Rupees Sixty Six Thousand Four

78 Responce Time - 10 milli second. (11) Protection requirements - Input low Cut off protection / 1.00 Each 66413.00

Hundred Thirteen Only

Input High Cut Off Protection / Output Low Cut Off protection / IOutput High (12) Fault

Annuciation Panel LED shows Input present, Input high Input low, Output Normal, Output

High, Outpur low, Overload. (13) Output On time delay - 10 seconds (14) Ambient

Tempeature capacity - 0 - 45 RH upto 90 %. (15) Enclosure Type - IP20 (16) Type of Cooling -

Air,Output:Bypass switch with changeover switch, & 5 year free replacement guarantee on

Stamp paper.

Loading and unloading of above item shall be done by hydra and skill work force under

supervision of electrical engineer and guidelines given by manufacturer to avoid damage to

the item. Picture of it to be submitted in running bill / final bill.Size of door and Ele. room /

Pump room shall be checked by agency's engineer before giving order. If found any problem in Rupees Nil

size discuss with GSPHCL engineer for rectification before giving order. 20 KVA (Air Cooled)

(make - Fuji-Electric,Servomax,Krykard)

Supplying and erecting approved make GRP/FRP Perforated type Cable Tray Material –

Corrosion Resistant Polyester Flame Retardant U.V. Stabilized Resin System - Manufactured

from Pultruded Sections- Polyester Resin System, Glass Content : 55 – 60 % - - Standard

Length : 3000 mm- Support Span – 1500 mm, Deflection L/200 - Specification NEMA FG1 1993-

UV Resistant - Flame Retardant – IS 6746 - Appendix K/UL 94, Very Low Flammability -

Specification Followed NEMA FG1 1993 Oxygen Index – Minimum 30% as per ASTM D 2863 -

Flame Spread (Extent of Burning) – 20 mm as per Standard ASTM D 635 - Tensile Strength – Rupees Five Hundred Twenty Six

79A 4000 – 8000 Kg/Cm2 as per Standard ASTM D 638 - Flexural Strength – 2500 – 10000 Kg/Cm2 30.00 Rn.Mtr 526.00

as per Standard ASTM D 790- Izod Impact Strength – 130 Kg/Cm2 as per Standard ASTM D

256- Compressive Strength – 2500 – 5000 Kg/Cm2 as per Standard ASTM D 695- Barcol

Hardness – 50 – 65. Width 300 mm, Side Member “C” Section : 100 x 35 x 35mm with 4mm

Thickness, Loading 60Kg./Mtr. With Concentrated Load 70Kg. at center of the span

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

Width 150 mm, Side Member “C” Section : 75 x 25 x 25mm with 4mm Thickness, Loading

79B 30Kg./Mtr. With Concentrated Load 70Kg. at center of the span. 30.00 Rn.Mtr 230.00 Rupees Two Hundred Thirty Only

Providing and erecting open well type horizontal submersible mono block pump set with

cast iron body having following specification [E] For 3 phase open well horizontal mono block

pump set suitable for 85 LPM to 270 LPM discharge at required head as per plumbing length

and vertical & Horizontal head. Agency has to submit the details calculation of head to

GSPHCL and get approval of make and model of pump having tender specification with TDS

& GA drawing. Suitable for 32/40/50/65/75 mm dia delivery pipe with 10 mtr. necessary Size

3 Core Flat copper flexible cable. (Body: Cast iron / Winding : Copper / stator : Copper / rotor

: Copper / shaft : SS / Carbon material test certificate from manufacture shall be Rupees Fifteen Thousand Five

submitted).The model of the pump with respect to head and discharge will be approved by Hundred Fifty Two Only

EIC. Pump should have following specifications: (1) Minimum 10 mtr. Cu. flat cable of suitable

size must be provided with pump.(2) Pump shall be installed as per manufacturer

foundation/erection drawing or as per IS specification. (Body full C.I., stator winding- copper,

rotor- copper, shaft- SS / carbon material, motor-Energy efficiency)

Supplying and erecting approved make 3 HP DOL type motor control cubical panel made

from 16 G. CRCA sheet duly epoxy powder painted inside and outside with hinged doors and

locking arrangement Floor Mounting On 300 mm Height with MS Stand Angle & CC

Foundation. Size 35 mm (H) x 35 mm (W) x 05 mm (D). The detail specification & quantity of

Rupees Forty Seven Thousand Sixty

81 material used are as under. 1.00 Each 47062.00

Panel must be with minilec relay for auotmatic change over for pump 1 & 2 logically without

using manually change over switch (Minimum Panel Size: 1.10 meter (H) x 1.10 meter (W) x

0.25 meter (D).

INCOMMER SECTION: (1) MCCB-30 KA-FP (DU-100H), Rating: 63 Amp., Make: L&T, Qty:

01 No. (2) Digital Ammeter (SR-65), Rating: 0-60 Amp., Make: Meco, Qty: 01 No. (3) Ammeter

Make: Salzer, Qty: 01 No. (6) C.T.- Current Transformer, Rating: 60/5 Amp., Make: Virat, Qty:

03 Nos. (7) Indicating Lamps (R,Y,B), Rating: 22.5 mm LED, Make: Airon, Qty:03 Nos. (8) SP Rupees Nil

MCB , Rating: 20 Amp., Make: L&T , Qty: 03 Nos. (9) Control Wiring, Rating: 1.0 Sq.mm,

Make: Any ISI, Qty: Lot (10) Copper Busbar, Rating: 63A/100 Amp., Qty: Lot (11) Numeric

logical relay, Qty: 1 No.

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

Outgoing Feeder (3 HP DOL Feeder): Qty: 02 Nos. (1) MCB-FP-10 KA, Rating: 20 Amp.,

Make: L&T, Qty: 02 Nos. (2) Power Contactor (415 V) Main, Rating: 12 Amp., Make: L&T, Qty:

02 Nos. (3) Over Load Relay, Rating: 6-10 Amp., Make: L&T, Qty: 02 Nos. (4) Digital Ameter

(SR-65), Rating: 0-20 Amp., Make: Meco, Qty: 02 Nos., (5) Digital Voltmeter (SR-65), Rating: 0-

500 V, Make: Meco, Qty: 02 Nos. (6) Indicating Lamps (Start,Run,Trip), Rating: 22.5 mm LED,

Make: Airon, Qty: 04 Nos. (7) Push Button (Start,Stop), Rating: 22.5 mm, Make: Airon, Qty: 04 Rupees Nil

Nos. (8) SPP, Rating: 415 V, Make: Space, Qty: 02 Nos. (9) Terminal, Rating: As per Amp.,

Make: Airon, Qty: 04 Nos. (10) Control Wiring, Rating: 1.0 Sq.mm., Make: Any ISI, Qty: Lot

(11) Power Wiring, Rating: As Per Amp., Make: Any ISI, Qty: Lot

Outgoing Feeder (6 Amp. - 01 No.) For Capacitor (1) MCB-FP-10 KA, Rating: 6 Amp., Make:

L&T, Qty: 01 No. (2) Capacitor- MPP Type, Rating: 2 KVAr, Make: Concap, Qty: 01 No., (3)

Rupees Nil

Power wiring, Rating: As Per Amp., Make: Any ISI, Qty:Lot

Outgoing Feeder (32 Amp. - 01 No.) For Lighting (1) MCB-FP-10 KA, Rating: 32 Amp., Make:

L&T, Qty: 01 No. (2) Power wiring, Rating: As Per Amp. (3) Earthing Strip: 25 x 3; G.I. Strip,

Qty: 01 No. (4) MCB-DP-10KA , Rating: 20A, Make: L&T, Qty.:01 Nos. Rupees Nil

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible Submersible

copper cable approved make of following Size. [c] 3 Core x 2.5 Sq. mm

82 20.00 Mtr. 103.00 Rupees One Hundred Three Only

Providing & erecting ISI make medium duty (B class) galvanized MS pipe with coupling,

bend, union, reducer, tee, MS flange etc. with plumbing charges. 50 mm dia. [make and model

83 20.00 Mtr. 260.00 Rupees Two Hundred Sixty Only

approved by EIC strictly as per tender specification]

Supplying and erecting C.I. Swing check type non-return (reflux) valve ISI marked with

packing, flange, nuts and bolts etc.suitable for following pipe size. [a] For 50 mm dia. (Make

84 3.00 No. 1010.00 Rupees One Thousand Ten Only

and model approved by EIC as per specification only)

Lowering of existing submercible motor pump set complete with required No. and size of

pipes by means of proper chain pulley block and pipe wrenches. Job includes stacking of pipes

Rupees Eight Hundred Forty Eight

85 cronologically after the checking of threads. [d] For open well horizontal submercible pump set 2.00 Each 848.00

for sump well. (ii) 1.0 HP to 5 HP

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

Providing and fixing of ABC Type Store Pressure Fire Extinguisher Having capacity 6 kg

Filled with Mono Ammonium Phosphate Powder 50% confirms to IS 4308, Stored Pressure

Type, UGTS Pressure Gauge, Can Height 530 mm, Diameter 150 ± 10mm, Discharge Time

Sec, Controllable discharge mechanism, Jet Range 5 Meters, Average Discharge is 92%,

applicable on Class A,B & C and electrically started Fire, Fire Rating 4A:144B, Can

Construction : Deep drawn & CO2 Mig welded, EPDM(Ethylene Propylene Diene Monomer)

Rubber Hose with both end Aluminum clamped, Internal Coating - Epoxy Powder coating,

External Coating - Pure Polyester Powder coating (UV Resistant),Brass forged CE Marked

valves with NRV & Auto Safety Release with safety Pin is of SS material, Made up from

1.6mm thick sheet, Extinguishers confirmed to IS 15683:2018 and ISI marked. Referance Rupees One Thousand Nine

86 Weight:-Gross Weight 8.9 Kg, Empty Weight 2.9 Kg, 1. Necessary certificate & and guarantee 2.00 Each 1991.00

Hundred Ninety One Only

must be attached, 2. OEM has to provide wall mounting heavy duty bracket/clamp, screw,

hardware for installation. 3.Following printed marking Manufacturing Date and Expiry Date

must be mention on Extinguisher 4. Refilling period must be of 3 Years. Following Printed

marking on equipment must be required:- Model No, Capacity, Gross Weight, Content, Fire

Rating, Batch No, Serial no, Mfg Month, Refilling Due. [with necessary numbering / marking

with oil paint by painter as instructions given by G.S.P.H.C.L engineer] (Make: KANEX,

MINIMAX, CEASEFIRE)

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

Providing and fixing of CO2 type High Pressure Portable 4.5 kg Fire Extinguisher, filled with

Co2 Gas as per IS 15222, Control discharge mechanism fitted with 1 Meter Wire Braided Hose

& Electrical non-conductor Polyethylene Flat Horn with Diffuser Nozzle for dispersed

discharge of CO2, Discharge Time 12 Sec, Average Discharge is 95%, Applicable on Class B, C

and electrically started Fire, Fire Rating 55B, Internal coating is not applicable & External

coating is of enamel spray painting, Powder Coated Handle, Valve Confirm to IS 3224 ISI

Marked, CO2 Cylinder construction: hot spinning by seamless pipes & bearing ISI mark, Body

confirms to IS 7285 and PESO ( Petroleum and Explosives Safety Organization) APPROVED,

Minimum Wall Thickness 4 to 4.2 mm, Extinguishers confirmed to IS 15683:2018 and ISI

marked. Referance Weight:-Gross Weight 16.4, empty weight 11.9 Kg, 1. Necessary certificate Rupees Six Thousand Five Hundred

& and guarantee must be attached, 2. OEM has to provide wall mounting heavy duty Twenty Six Only

bracket/clamp, screw, hardware for installation. 3.Following printed marking Manufacturing

Date and Expiry Date must be mention on Extinguisher 4. Refilling period must be of 5 Years.

Following Printed marking on equipment must be required:- Model No, Capacity, Gross

Weight, Content, Fire Rating, Batch No, Serial no, Mfg Month, Refilling Due. [with necessary

numbering / marking with oil paint by painter as instructions given by G.S.P.H.C.L engineer]

(Make: KANEX, MINIMAX, CEASEFIRE)

Providing & erecting Point wiring with 1.1 KV grade ISI marked 2 X 1.5 sq. mm copper PVC

insulted FRLS wire with 1.5 sq. mm (green) copper PVC insulated FRLS wire for earth

continuity in FIA approved ISI mark medium class white colour 20/25 mm dia. embossed

rigid PVC pipe with PVC fitting fixed with adhesive solution erected on Brick Wall along

with continuous G.I. fish wire to draw wires and laid in approved manner zari for PVC pipe

and boxes shall be filled with cement mortar and finishing the surface to match the wall /

ceiling complete with approved make 5/6 Amp. ISI make modular type switch and accessories Rupees Four Hundred Forty Five

88A mounted in 20 G. G.I. company fabricated metallic box covered with appropriate front plate 10.00 Point 445.00

modules erected flushed with wall / ceiling with necessary modular lamp holder / modular

ceiling rose / HD Connector as directed..(Deep Junction box 75mm depth if required)(Make &

Model approved by EIC and matching colour with switch and accessories) for Open wiring.

Light point. -.(a) with medium class Rigid PVC pipe and accessories erected flushed on

wall/ceiling complete CAT III (For Conferance Hall)

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

Necessary sheet / tape / polythene / sand must be erected or filled in all box to prevent

mortar going into the box. Length of point wiring must not increase than 10 mtr. For that

necessary switch boards and their locations must be finalised before execution by agency

otherwise payment will not be done for extra long point. (For future extention, if required,

agency has to erect one higher size metal box and modular plate as per instruction of EIC. Cost Rupees Nil

of blank plate shall be paid as per tender item) [This item include cleaning (inside/outside) of

all G.I. switch boards, electric point box, fan box, MCBDB & box cutting plaster finishing for

modular plate without any gap]

For Fan Point (with 6 A. Modular type switch and two module hum free EME Five step type

Electronic fan regulator both having ISI mark) with medium class Rigid PVC pipe and Rupees Six Hundred Thirty Two

88B 5.00 Point 632.00

accessories erected flushed on wall/ceiling complete CAT III Only

For separate Point (with 6 Amp. Switch & 3/5 pin socket both having ISI mark)with medium

class Rigid PVC pipe and accessories erected flushed on wall/ceiling complete CAT III Rupees Four Hundred Seventy One

88C 3.00 Point 471.00

For Looped on switch board (with 6 Amp. Switch & 3/5 pin socket both having ISI mark) Cat.-

Rupees Two Hundred Fifty Five

88D IlI 6.00 Point 255.00

Providing following type of Modular Type Accessories mounted with PVC /

metallic/Wooden box, single mounting base frame covered with textured / metallic/white

Rupees One Hundred Fifty Nine

89A front plate , modules erected with necessary connections as per site situation directed by 1.00 Each 159.00

Engineer In charge.TV Co-axial Socket Outlet. Cat.-III

For Modem Jack for Computer Open RJ-45. Cat.-III. Rupees One Hundred Fifty Nine

89B 2.00 Each 159.00

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

Providing & Erecting Plug Point wiring with 1.1 KV grade ISI marked approved make 2 x

sq.mm copper PVC insulated FRLS wire with 1.5 sq.mm (green) copper PVC insulated FRLS

wire for earth continuity in FIA approved ISI mark white colour medium class 20/25 mm

dia. embossed rigid PVC pipe with PVC fitting fixed with adhesive solution erected on brick

wall along with continuous G. I. fish wire to draw wires and laid in approved manner zari for

PVC pipe & boxes shall be filled with cement mortar & finishing the surface to match the wall Rupees Seven Hundred Thirty Eight

90 / ceiling complete with 16 Amp Modular type Swich and accessories mounted in 20 G. GI 3.00 Point 738.00

company fabricated metallic box covered with appropriate front plate modules erected flushed

with wall. (a) 16 Amp Indicator switch & 1 No. 6/16 A universal socket white colour suitable

for 3 pin top duly both having ISI mark. (Necessary Sheet Must Be Erected On All Box To

Prevent Mortor Going In To The Box) Cat.-III

Plug Point wiring with 1.1 KV grade ISI marked approved make 2 x 4.0 sq.mm copper PVC

insulated FRLS wire with 1.5 sq.mm (green) copper PVC insulated FRLS wire for earth

continuity in FIA approved ISI mark white colour medium class 20/25 mm dia. embossed

rigid PVC pipe with PVC fitting fixed with adhesive solution erected in brick wall/slab along

with continuous G. I. fish wire to draw wires and laid in approved manner zari for PVC pipe

& boxes shall be filled with cement mortar & finishing the surface to match the wall / ceiling Rupees Eight Hundred Sixty Three

91 complete with 16 Amp Modular type Swich and accessories mounted in 20 G. GI company 2.00 Point 863.00

fabricated metallic box covered with appropriate front plate modules erected flushed with

wall. (a) 16 Amp switch & 1 No. 6/16 A universal socket white colour suitable for 3 pin top

duly both having ISI mark. (Necessary Sheet Must Be Erected On All Box To Prevent Mortor

Going In To The Box) Cat.-III

Providing & erecting Switch board for Computer or electric apparatus consisting of following

items in single board erected on 20 G. G.I. company fabricated metallic box erected with

appropriate front plate modules erected flushed with wall as directed. 1 no. 6/16 Amp.

Rupees One Thousand One

92 universal Socket, 1 no. 13 Amp. international socket, 2 nos. 16 Amp. indicator switch, 2 nos. 6 2.00 Nos. 1122.00

Hundred Twenty Two Only

Amp. Switch & 2 nos. 6 Amp. 5 pin Plug. For Computer power Supply board. Cat.-III

Supply, Installation testing and commissioning of 16 Gauge M.S. Powder coated floor raceway

Access outlet / service junction box with 16 Gauge M.S. Powder coated Cover plate with duct

entry 25 mm / 38 mm size having epoxy powder coated trap lead with corrosion & rust free Rupees Seven Hundred Forty Nine

with adjustable levelling screw of following size. [a] 300 mm x 300 mm x 50 mm depth Only

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

SITC of specified make Cat - 6 voice /data cable to be done in prelaid PVC pipe / raceway

but without the cost of raceway or pipe ( the wire is to be drawn from MFD/ JB to outlet

94 point) (a) CAT - 6-Y Colour ( For Voice Cabling ) & X -Colour(For Computer Data Cable ) .( 70.00 Mtr. 47.00 Rupees Forty Seven Only

Molex/Avaya/Systimax/Legrand make)

SITC of Indoor Commercial Recess / Surface mounted (IP20) 24 W Cool/Warm white Color

BacklitLED Down lighter office Lighting Luminaire with separate potted driver with single

piece pressure die cast aluminium alloy housing with corrosion resistant powder coated finish

with PMMA/PS/Injection moulded Polycarbonate diffuser with high brightness LED

complete, CRI > 80, with 24 W. The LED's should be mounted on metal core PCB for better

heat conduction and long life of LED. The Fixture should comply all International Standarad

third party (LM 79 for complete fixture, LM80 for individual LED). The Fixture have protection

like miswiring, over voltage, over load, wrong wiring, THD < 15%,, P.F > 0.95, efficacy >

lm/w & driver efficiency > 85%. For 24 W fixture wide voltage range from 160 V to 270 V,

50/60 HZ @ 240V application, 2 KV surge protection.The fixure must have min. 2160 lumen

light output.The fixture should be provided with external separate Potted driver, latest Valid Rupees Seven Hundred Fifty One

BIS approved Luminaire and driver. The Fixture efficacy > 90 lumens/watt only for safety and Only

performance. (L70 @ 30,000 Hrs.) The fixture should be able to easily mount on POP / Grid

false ceiling. The Luminiare should be tested as per IP 20 and following test reports should be

submitted at the time of approval: heat resistant test, thermal test, Ingress protection test, drop

test, Photobiological report with 3 core X 1.0 Sq.mm. flexible wire as per site requirment [Note:-

The manufacturer / authorized Channel partner of the manufacturer has to submit 5 yrs. free

replcement Guarantee for complete Fixture]

Providing and erecting Inverter based approved make split air-conditioning unit consisting of

condensing unit with variable speed fan motor, inverter type hermetically sealed rotary

compressor with accessories etc. duly connected separately erected evaporating unit and

blower motor with its accessories by means of extra supplied proper insulated copper Rupees Fifty One Thousand One

96 tubing,drain PVC pipes suitable for ( cost includes Eco Friendly green gas charging and 15A 2.00 Each 51155.00

Hundred Fifty Five Only

plug top & Remote Control & MS Stand) with necessary core cutting.(1)For ISEER Range

(KWH/KWH)(3.1 to 3.99) for 2 ton capacity( Make &Model Approved By EIC)

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

Extra charges for the item of copper tubing with minimum 19 mm thick class 0 nitrile rubber

insulation for entire piping system exposed refrigerant piping should be additionally insulated

with factory laminated 200 GSM glass coth for UV and mechanical protection and

manufacturer accomoded adhesive ( solvent free ) sealant applied at all joints (including

Refrigerant Joint) UV protection layer. additional layers of UV paint over GC for all exposed to Rupees Nine Hundred Fifty Six

atmosphere piping for weather protection of pipes & insulation and prevention of rain Only

waterigress. item beyond standardlength for single phase / three phase Split A.C. Machine /

Cassate A.C. Machine including power and control cable up to 4.0 TR capacity.

Supplying and laying UPVC cable trunking system comprising unplasticised polyvinyl,

chloride rigid material with ignition free and flame proof confirming BS with necessary end

caps Internal and external bend, flat bends, coupler, tee etc..All necessary accessories and Rupees Four Hundred Twenty Four

measuring of following sizes. FOR 100 mm x 50 mm trunking Only

SITC of of 2Dual-channel power amplifier 2 x 240W 100V Lightweight class-D amplifier

Advanced protection circuit XLR input & linkthrough connections with gain control & HPF

switch Terminal block output connections High-pass filter switchFrequency Response (± 3 dB)

50 Hz - 22 kHz Signal / Noise > 100 dB Technology Class-D Power Supply Switching mode

Source 230 ~ 240 V AC / 50 Hz Inputs Sensitivity -0.5 dB ~ 10.5 dB Impedance 10 kΩ balanced Rupees One Lakh(s) Six Hundred

99 Connector XLR female with Male Linkthrough Outputs Voltage / Impedance 100 V / 42 Ω 1.00 Each 100606.00

Connector 4-pin Euro Terminal Block (Pitch - 5.08 mm) .

[Make:- Audac / Workpro Zenith 1000 / EAW / Bose and equivalent make and model

approved byt EIC Only]

SITC of Column loudspeaker 40W, metal, black.

[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ]

Rupees Twelve Thousand Three

100 [Make:- Workpro NEO 5 / Bose / Martin Audio and equivalent make and model approved 6.00 each 12349.00

Hundred Forty Nine Only

byt EIC Only]

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

SITC of Handheld Wireless Mic with Cardiod polar pattern,Dynamic microphone ,frequency

response 80Hz-18kHz,RF sensitivity < 1.0 Uv,Image rejection>55dB,Dyanmic range >95dB and

receiver having 30 or more channels possible,S/N ratio >100dB A,dynamic range >95db

B,distortion <1 %,frequency band:618-634MHz,more than 12hrs battery life with AA

battery.The transmitter & receiver should be of metal body (Including Five year free Rupees Sixty Seven Thousand Six

maintenance with guarantee) Hundred Thirty Only

[Make:- Erhtpot AR-31 / Clock Audio / Brahler,and equivalent make and model approved

byt EIC Only]

Supply,Installation,Testing and Commissioning of 30 ft HDMI Interface Cable

Should be 30ft Male to Male High-speed Category 2 HDMI cable; Should be 24k

gold-plated 19-pin Type A connector; Should have High-flex CL3-rated jacket;

Should Support 4K30 4:4:4 and 4K60 4:2:0 video; Should support 18 Gbps

Rupees Fourteen Thousand Four

102 bandwidth; Should be RoHS compliant (Including Five year free maintenance 3.00 Each 14407.00

Hundred Seven Only

with guarantee) [Make:- MX / Kramer / Extron / and equivalent make and

model approved byt EIC Only]

Supply,Installation,Testing and Commissioning of 3 ft HDMI Interface Cable

Should be 3ft Male to Male High-speed Category 2 HDMI cable; Should be 24k

gold-plated 19-pin Type A connector; Should have High-flex CL3-rated jacket;

Should Support 4K60 4:4:4 video; Should support 18 Gbps bandwidth; Should Rupees Four Thousand Two

be RoHS compliant (Including Five year free maintenance with guarantee) Hundred Thirty Seven Only

[Make:- MX / Kramer / Extron / and equivalent make and model approved byt

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

SITC of 3LCD Lamp based projector having wxga (1280x800) or better

resolution with minimum white brightness of 3800 lumens and color brightness

of 3800 lumens. The projector should have minimum 1HDMI,1VGA input.

Having contrast ratio of 15000:1 or more. the projector should have auto vertical

key stone correction of +/- 30 degree and Manual Horizontal of +/-30 degree.

the projector should have optical lens, throw ratio 1.30-1.56:1. Zoom Factor of

1.2. Lens focus Manual having focal length 16.9mm to 20.28mm. projector Rupees Thirty Three Thousand Five

104 should have features like AV mute slide, quick corner and split function and 1.00 Each 33560.00

Hundred Sixty Only

should support wireless functionality with inbuilt wifi or wifi dongle.

[Approved by Competent Authority i.e. not Below the rank of Executive

Engineer ] (Make : Epson / Sony / Panasonic and equivalent make and model

approved byt EIC Only)

SITC of 120 inch Diagonal Self Lock MW Instalock Slow Retraction Screen,

Rupees Five Thousand Two

105 Aspect Ratio-16:9 1.00 Each 5282.00

Hundred Eighty Two Only

SITC of universal Projector mounting kit, with necessary grouting, fasteners etc.

with adjustable height and suitable for all types of projectors. [Approved by

Rupees Six Thousand Seven

106 Competent Authority i.e. not Below the rank of Executive Engineer ] 1.00 Each 6781.00

Hundred Eighty One Only

SITC Hydrolic popup box with HDMI , VGA , with audio 3.5 mm jack , lan

AMP power. (Make and model approved bhy EIC Only) (Including 3 years Rupees Eight Thousand One

warranty) Hundred Eighty Six Only

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

SITC Mono Audio/Control Cable, is a high−quality shielded pair cable

designed for routing balanced mono or unbalanced stereo mic or line level

audio signals in commercial or residential AV systems. Conductors and drain

wire are stranded 20AWG tinned copper With sequential markings every meter..

Exceptionally easy to strip because the foil shield is bonded to the inside of the Rupees One Hundred Twenty Two

jacket., with white colour medium class PVC pipe , As directed By Engineer In Only

charge[Make:- MX / Kramer / Extron, and equivalent Make and model

approved bhy EIC Only)]

Providing and erecting 4 x 2 HDMI matrix switcher ,4 HDMI inputs & 2 HDMI

outputs ,Max. resolution 4K@60Hz (4:2:0) & 4K@30Hz (4:4:4) HDMI ,support

max. resolution 4K@60Hz (4:2:0) & 4K@30Hz (4:4:4)HDMI Suppot Color, 3D,

ARC, up to 7.1 uncompressed audio channels , Data rate up to 8.91 Gbps

,reclocks and equalizes the signal ,standards Compliance: HDMI 1.4 and HDCP

Rupees One Lakh(s) Seven

Thousand Two Hundred Eight Only

or last connected input ,Flexible control options viz Front Panel, Ethernet with

built-in webpages & RS-232 erected as directed by engineer in charge[Make:-

KRAMER / AMX/ EXTRON / CRESTRON,and equivalent Make and model

approved bhy EIC Only)

Supply and installation of 19 U Equipment steel rack Floor mounting for

installing Amplifier,Scalar, Wireless mic receiver etc, rack should be fully

enclosed steel housing fabricating with powder coated with glass doors and

having wire nos. wire management system . the rate includes the exhaust fan 2 Rupees Twenty Four Thousand One

nos, 6 Sockets and 1 switch power strip and all the wiring in the rack.. (Including Hundred Fifty Three Only

Three year Warranty) [ Make: Elixir / Rittal / Valrack]

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

SITC 2 Core Speaker Cable , is a high−quality 99.999% OFC Résistance :

Ω/m Capacitance : 55,530 pF/m, Section : 2x1,5mm2 Dimensions

:415x160x215mm , Cable as comfortable with micro-information as they are with

high power twisted pair cable designed for connecting speakers and amplifiers .

111 100.00 Mtr. 72.00 Rupees Seventy Two Only

( Make- MX , Norstone , Belden , Kramer,and equivalent Make and model

approved bhy EIC Only)

Supplying & erecting Mixing Console having channels, Audio mixer with. Echo facility for live

performance, Auditorium & stadiums, having following features & facilities. [[Approved by

Competent Authority i.e. not Below the rank of Executive Engineer ] (a)input Channels :- Each

channel has separate 6.25mm size balanced phone jack for mike & line for balanced &

unbalanced signals.(b)Individual gain control for sating optimum level for minimum noise.

(c)BASS, MID & TREBLE ‘ controls Separately for each input channel.(d)ECHO control for

each channel (e)PAN control for echo channel for left or right output(f) AUX Control : To

control , level of the channel in final mix to AUX sound output(g)Channel ON/OFF

switch(h)ECHO Section :- ECHO, reverb & Chorus effect can be added to all input channel by

different setting of Delay, Reverb & Level control.(i)Tape section (j)Aux. send & return For

sending Pre-feeder output of channel for monitoring or adding a special effect unit.(k)Mono /

Stereo output controls(L)Master faders to control over left & right (m) Head phone output for

Rupees Twelve Thousand Two

112 monitoring purpose.Technical specification:(a)Power Requirement -AC220-24OV 50 Hz DC 1.00 Each 12289.00

Hundred Eighty Nine Only

24 Volts (b)MIC Output Impedance/gain -2 K Ohms/ 62 dB (c)Line Output Balance/42

dB —- 20 K ohms (d) Impedance / Gain :- 10Kohms unbalance / 42 dB (e)frequency

Response - 30 Hz- 20 KHz L / R Line Output ( + 0, -1 dB ) (f)Equalization Bass/ - + / -

12 dB at 100Hz Mid / Treble 2 KHz / 10 KHz (g) Outputs, Line Output Line Output Low

: -10 dB / -2 dBM Line Output High

: 0 dBM / +17 dBM (775 mv / 5.5 V ) (h) S/N ratio Line Output Level : > 70 dB (0 dB,

0.775V) The Console shall be mounted on standard Rack, The channel of following

numbers.(B) 9 Channel Audio Mixer with ECHO

[Make:- Studiomaster / Ahuja / Behringer and equivalent Make and model approved bhy EIC

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

SITC of Delegate Unit shall enable delegates to speak and listen to the

proceedings via a loudspeaker or headphones. The unit shall include a

microphone with a red indicator ring, which shall illuminate when the

microphone is on.

The unit shall include a ‘Possible To Speak’ white LED indicator, which shall

illuminate showing the delegate when it is possible to switch on the

microphone.To prevent acoustic feedback, the built-in loudspeaker shall be

muted when the microphone is on, and/or the headphones are connected.Two

3.5 mm stereo headphone sockets (wired for mono) shall allow two pairs of Rupees Thirty One Thousand Seven

headphones to be connected, enabling two delegates to simultaneously use the Hundred Seven Only

The headphone volume level shall be adjustable on the unit for maximum

comfort. It shall also be possible to connect a tape recorder to one headphone

socket, and use the other headphone socket to listen to the proceedings.

[Make:- Erthpot NCS-5D / Brahler / Telvic,and equivalent Make and model

approved bhy EIC Only.]

SITC of Chairman Unit shall enable the user to function as chairman of a

conference or meeting. It shall be similar in appearance to the Delegate Unit, and

shall also include a ‘chairman priority button.When pressed, the priority button

shall cause all currently active delegate microphones to be temporarily or

permanently muted, allowing the chairman to take control of the meeting.To

prevent acoustic feedback, the built-in loudspeaker shall be muted when the Rupees Thirty Eight Thousand

microphone is on, and/or the headphones are connected.An optional chime Three Hundred Forty Three Only

Brahler / Telvic,and equivalent Make and model approved bhy EIC Only)]

Item Qty. Unit Estimated Rate [Rs. Ps.] Amount

Description of Item

No. InFigure In Words Rs.

SITC of Control Unit shall have features for managing the number of active

microphones and determining the operating mode, without the need for a

central operator, should be available. It shall be possible to control up to

delegate units and power up to 50 delegate units.It shall be possible to connect

external equipment to extend the system capabilities. There shall be a built-in

Rupees Ninety Four Thousand Two

115 loudspeaker and headphone connector to allow the conference to be monitored 1.00 Each 94226.00

Hundred Twenty Six Only

by, for example, a stenographer.

[Make:- Erhtpot NCS-110U / Brahler / Telvic, and equivalent Make and model

approved bhy EIC Only.

Ele Amount

Total Amount

Total Amount

Exeucutive Engineer

Signature of Contractor G.S.P.H.C,Limited.