Comprehensive maintenance like repair/replacement of tilling, joinery, plumbing and certain misc works to Zone-5, Zone 1 (B) and (C) and Repair/Replacement of sewage line-1 (B), Zone-1 (C) and Zone-5 under GE (S) Tezpur

Amount

Demolition and breaking-up of 150mm nominal dia unserviceable SGW, AC,PVC or re-enforcement concrete, set in cement mortar including PCC haunching complete and removing to a distance not exc 50 meter complete all as specified and directed.

M&L P.C.C (1:3:6) type C2 using 40 mm graded stone aggregate for bed to drain pipes including packing under and hunching against side of pipes after they are laid down and tested complete for 150 mm bore pipe complete all as specified and as directed.

M&L 150 mm internal dia salt glazed stoneware drain pipes , laid in trenches and jointed as specified all as specified and as directed

Demolition of cement concrete in ground floor and pavings n exc. 15 cm thickness (below or above the ground level) (Un-reinforced) and removing to a distance not exc 50 meter complete all as specified and as directed

Dismantling fencing post, strut (wood, Steel or RCC) any section, including taking out embed portion and making good disturbed ground embedded in concrete all as specified and directed.

Dismantling chain link fencing, any thickness or mesh, fixed with steel fillet and nut bolt. N.exc 4KG per Sqm all as specified and directed.

Excavating in post holes(or similar holes) each 0.50cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering and removing surplus soil to a distance n exc 50m and making good all as specified and directed.

M&L PCC (1:3:6) Type C-2 using 40mm graded stone aggregate) as in foundation all as specified.

S & F Angle iron as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 all as specified and directed.

S&F in repairs Galvanized 2 strand, steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75mm spacing and staining and fixing to any type of standard rails strain -in bolts, including, securing or tying at crossings with and provision of galvanized mild steel wire, staples or steel pins etc as directed (each line wire to be measured.) all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire

Supply only chain link fencing any size and type all as specified and directed.

S&F Mild steel screw bolts (machine made) 08 to 12 mm dia of neck with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long all as specified and directed.

Cutting into existing manhole for connection new drain making good to pipe and rendering cutting out existing benching and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finish and reforming benching as required for 75 mm to 150mm dia.all as specified and directed.

M&L for Cement concrete 1:3:6 type C2 (using 40 mm graded crushed stone aggregate) as in surface channels, drains including all necessary form work complete all as specified and directed.

M&L extra for forming fair finished drain or channel 30 cm and over inner girth in cement concrete, using extra cement, including forms, moulds, mitered/ stopped ends etc complete all as specified and directed.

M&L extra for forming fair finished drain or channel under 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitered/ stopped ends etc complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding(but not backing) complete and removing rubbish off the premises complete all as specified and directed.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified and directed.

M&L 25 mm thick PCC type B-1, 1:2:4 (20mm graded aggregate) as in sub base/floor etc complete all as specified and as directed.

M&L Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6 (rate included) all as specified and directed.

M&L Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6 (rate included) all as specified and directed.

S&F Coloured Glazed ceramic tiles 450 x 300 mm x 6 to 7mm thick, in skirting /dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm rendering in Cement mortar 1:4 (rate included) all as specified and directed..

Demolition of reinforced cement concrete of any description and in any position all as specified and directed.

M&L for RCC type B1 1:2:4 (20 mm graded agg) as slab supported on wall , beams columns in floor, roofs landing and the like all as specified and directed.

S&F Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Use & Waste of Formwork to sides and soffits of floor or roof beam , beam haunching, girders ,lintels shelves including support and hangs all as specified and directed.

Demolition of brick work built in cement mortar including pillar etc below/ above ground level etc and removing to a distance not exc 50 meter. complete all as specified and as directed

M&L Brick work with sub class 'B' bricks, straight or curved on plan exc 6 m mean radius, built in CM 1:6 complete as specified

Material and labour for brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar ( 1:6) all as specified and directed.

Taking down cement plastering on brick or stone walls etc, including raking out joints, hacking for key scrubbing down with water etc.

M&L rendering 15 mm thick cement plaster on brick wall in CM 1:4 mixed with WPC @ 3% by weight of cement and finished even and smooth without using extra cement complete all as specified and as directed. (Note : WPC will be measured and paid for separately)

M&L 10mm thick rendering in cm (1:6) on fair faces of brick work or concrete surfaces and finished even and smooth without using extra cement all as specified and directed.

Supply only water proofing compound. Conforming to IS -2645.all as specified and directed.

M&L preparation of newly plaster surfaces and applying two coats of acrylic exterior paint (Anti Fungal Paint) over coat primer to new plastered walls as per manufacturer and applied by approved applicator complete all as specified and directed.

M&L Applying two coats of Acrylic Emulsion distemper (by smart painting) to newly plastered/previously untreated wall over 1 mm thick layer wall care putty over a coat of primer including preparation of newly plastered wall all as specified and directed.

Material and labour for applying three coats of white wash on walls including preparation of new or previously untreated surfaces all as specified and directed.

Taking down existing damaged water closet along with complete PCC from sunken floor area not exceeding 1.2 SqM and providing new EWC / IWC after water proofing treatment to sunken floor as per following stage :- (i) 15mm thick plastering in CM (1:2) with WPC at all around and base of sunken floor with proper slope. (ii) Applying a coat of 85/25 gde hot bitumen @ 0.7Kg/Sqm over a coat of bituminous primer @0.5Kg/Sqm and then pasteing of 150 micron polythene film / 3mm APP membrane, natural colour with cold cut back adhesive. (iii) Providing cement concrete to fill up the sunken floor (PCC 1:4:8) after testing of water tightness. all as specified and directed.

Supply and fix, as in repair, vitreous china wash down water closet pan (Pedestal pattern) white (excluding flushing cistern and flush pipe) including seat cover white closed type complete all as specified and directed

Supply and fix, as in repairs, vitreous china squatting pan of Orissa pattern size 580mm x 440 mm, white, with integral foot rests (excluding flushing cistern and flush pipe) including connection making good to floor all as specified and directed.

Supply and fix in repairs bowel urinal flat back of size 465 x 355 x 265mm (minimum), white, with grating and union for discharge pipe, (excluding flushing cistern, flush pipe and waste pipe) complete including providing and fixing plugs, bedding urinals against wall in cement mortar (1:2) securing urinals to plugs with and including 60 mm brass screws and pointing around urinals back in cement all as specified

Supply and fix, as in repairs, plastic water closet seat, closed pattern with flat bottom, and cover for water closet pan (pedestal pattern) all as specified and directed.

S&F in repairs stainless steel grating 100/75mm dia all as specified and directed.

Supply and fix, as in repairs, Hand Shower (Health Faucet) (Brass chromium plated) with 1 Meter Long Easy Flex Tube in Chrome Finish & Wall Hook complete all as specified and as directed.

Supply and fix, as in repair, 10 ltrs capacity PVC valve less symphonic action type, low level flushing cistern, white, with inlet, ball valve float and handle including brackets & flush pipe of polyethylene of low or high density or PVC 32 mm dia complete all as specified and directed.

Supply and fix, as in repair,15 mm dia 600 mm long connection pipe with two PVC PTMT nuts at each ends with rubber washer complete all as specified and directed.

Supply and fix, as in repairs, 75 mm dia of outlet PVC(SWR) floor trap, plain with grating including jointing with solvent cement all as specified and directed

S&F Stack clamps including bolts and nuts and securing ends of stays to wall or roof for 100/75mm bore complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) all as specified and directed.

Supply and fix, 110mm bore PVC (SWR)pipe single socketed with rubber ring joints fixed to walls all as specified and directed.

S&F in repairs PVC (SWR) 110mm dia bends any radius all as specified and directed.

S&F in repairs PVC (SWR) branch 110mm bore pieces, single ( single Y ) equal or unequal all as specified and directed.

S&F in repairs PVC (SWR) junction110mm bore single ( single t) equal or unequal all as specified and directed.

Supply and fix, PVC cowls 110 mm bore all as specified and directed.

Supply and fix, 75 mm bore PVC (SWR)pipe single socketed with rubber ring joints fixed to walls all as specified and directed.

S&F in repairs PVC (SWR) 75 mm dia bends any radius all as specified and directed.

S&F in repairs PVC (SWR) branch75 mm bore pieces, single ( single Y ) equal or unequal all as specified and directed.

S&F in repairs PVC (SWR) junction75 mm bore single ( single t) equal or unequal all as specified and directed.

Supply and fix, PVC cowls 75 mm bore all as specified and directed.

Taking down chowkats or frames not exc 1.5sqm each with shutters( without taking off shutters from the frame ) including dismantling of PCC bed blocks for hold fasts all as specified and directed.

Taking down chowkats or frames exc 1.5sqm and not exc 4.0 sqm each with shutters ( without taking off shutters from the frame ) including dismantling of PCC bed blocks for hold fasts all as specified and directed.

Taking down of shutters of any description exc 1.00 Sqm and n.exc 2.00 sqm each all as specified and directed.

Taking down of shutters of any description n.exc 1.00 Sqm and each all as specified and directed.

Refixing of shutters of any description exc 1.00 Sqm and n.exc 2.00 sqm each in same opening including of taking down, easing, adjusting and renewal/refixing of builders hardware as required including renewal of unserviceable screws, etc all as specified and directed.

Refixing of shutters of any description n. exc 1.00 Sqm each in same opening including of taking down, easing, adjusting and refixing/renewal of builders hardware as required including renewal of unserviceable screws, etc all as specified and directed.

Material and labour for providing Plain Cement Concrete (1:3:6) type C1 using 20mm graded aggregate as in bed block or hold fast all as specified and directed.

S&F 2nd class hard wood plain, solid, straight in chowkats and framed rebated on the solid rounded or chamfered put together with glue pinned at joints including making rebate for fixing second shutter as per site requirement all as specified and directed.

S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides all as specified and directed.

Supply and fix 30mm thick second class hard wood glazed and skeleton, open rebated and prepared to receive glass/ wire cloth, gauze exc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. The sizes of members of shutters as per IS-1003 (Part-2), kiln seasonable and chemically pressure treated and fitted to chowkats complete all as specified and directed. (Note : Glass / wire cloth will be measured and paid separately).

S&F factory made solid PVC door frame of size 50mm x 47 mm made out of 5mm plain coloured PVC sheet reinforced with MS square tube as specified. Including tacking down old one with shutter as specified & directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top & bottom rails MS frame shall be covered with heat molded plain colour PVC 'C' channel having a PVC stiles and plain colour PVC sheets for top rail, lock rail bottom rail on either side & as gap insert for top rail & bottom rail paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stile & rails with suitable PVC sheet beading & jointed together with solvent cement all as specified and shown on drawing.

S&F 100mm size type B-21 Butt hinges extruded aluminum alloy with galvanized MS sheet hinges pin anodized all as specified and directed.

S&F 75mm size type C-21 Butt hinges extruded aluminum alloy with galvanized MS sheet hinges pin anodized all as specified and directed.

S&F extruded aluminum alloy handles fabricated type, anodized, 150mm long all as specified and directed.

S&F extruded aluminum alloy handles fabricated type, anodized, 100mm long all as specified and directed.

S&F Aluminum anodised sliding door bolts of size 300mm long, with hasp & staple ( bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy all as specified and directed.

S&F Aluminum anodized barrel tower bolts of extruded section 200 mm long and fixed with screws all as specified and directed.

S&F Aluminum anodized barrel tower bolts of extruded section 150 mm long and fixed with screws all as specified and directed.

S&F (in repair) for 2nd class hard wood small fittings such as shaped door & window stops, cleat including all necessary labours, articles not exceeding 200 cubic centimeter each complete all as specified and directed.

S&F (in repair) MS helical door spring 150 mm size incl roller and roller plate fixed to wooden or steel frames with welding etc complete all as specified and directed.

S&F in repairs 100 mm Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F steel windows with side hung shutter including projecting type hinges with steel handle and steel peg stay, complete with glazing bars, donetailed or welded all as specified and directed.

S&F steel window with side hung shutter, including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified.

Supply and fix, steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples ON NEW SURFACE all as specified and directed.

S&F in repairs Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staplesall as specified and directed.

Hacking out old broken glass any thickness, size, quality or description from wooden / metal frame works, glazed with putty or fixed with beads all as specified and directed.

S&F 4 mm thick frosted/ pin headed glass in ventilator shutters all as specified and directed

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.50 sqm in each pane complete all as specified and directed.

S&F in repair of pre-laminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work thickness of 12 mm complete all as specified and directed.

Material & Labour in repairs 19/20 mm thick Block boards, grade 2 quality, interior grade, laminated sheet with decorative face, veneer on one face, commercial type fixed with screws to timber frame work complete all as specified and directed.

S & F Continuous (piano) hinges, 30 mm width of flaps ,mild steel, bright finish or electrogalvanised complete all as specified and directed.

S&F bal catches with 8 mm dia steel ball magnet catches for cupboard shutter including strking plate as approved etc complete all as specified and as directed

Dismanting timber scantling 40 Sqcm and over in section in any position in framed work all as specified and directed.

M&L 2nd class HW in scantling fixed clean swan in framed work all as specified and directed.

Dismanting timber scantling under 40 Sqcm in section In fillests, rails , posts, rafters and purlins etc in any position in framed work or unframed work all as specified and directed.

M&L 2nd CL HW plain fillets square, rectangular in section clean sawn sectional area exe 13 sqcm & n.exe 25 sqcm fixed with nails including one coat of black oil all as specified and directed.

S&F in repairs stainless steel decorative curtain rod of 25 mm bore complete all as specified and directed.

S&F in repairs stainless steel decorative curtain brackets and end cap complete all as specified and directed.

Supply & Fix in repairs floor door stopper of brass body and tongues with hard drawn steel spring, overall length cover plate 150mm complete all as specified and directed

Dismantling Wall and ceiling boards (fiber, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets all as directed.

S&F false ceiling with powder coated exposed G.I. grid suspension system Everest E-Grid T-2430 or equivalent load carrying capacity with mid span deflection not exceeding 1/360 span with hanger spacing of 1200 mm c/c) consisting of Main Runner (3600 mm long, 0.25 mm thick, 38mm height) Cross Tee (1200mm/600mm long, 0.25 mm thick, 27 mm height) and Wall Angle (3000 mm long, 0.4 mm thick, 22 mm height). The Wall Angle shall be fixed on PVC Dash Fasteners on the perimeter of the wall by steel screws with distance 300 mm c/c. The Main Runners to be placed @ 1200mm, The Cross Tee 1200mm will be inserted in the pre-cut slots of Main Runner at a regular interval of 600 mm to form a modular grid of 1200mm x 600mm. Additional Cross Tees of 600 mm shall be placed perpendicular to the Cross Tee 1200 mm long to finally form a grid of 600mm x 600mm. Grid of module size 600mm x 600mm shall be supported by 6 mm dia G.I. wire from purlins/soffit. 4 mm thick High Pressure Steam Cured Everest Non Asbestos Fiber Cement Designer Ceiling Board or equivalent quality having Density>1200 Kg/m3, size 595mm x 595mm, confirming IS 14862 & Type B Category III of ISO 8336, tested as per AS-1530 part 3 & BS-476 Part 4,5,6,7&8, should be placed in the Grid module to form a False Ceiling.

S& F in repairs of 4mm thick MDF board embosed type in false in any type of frame work all as specified and directed (Make:Green Ply or approved ISI marked

Dismantling asbestos cement corrugated semi corrugated etc sheets in roof covering all as specified and directed.

S&F 0.5mm thick pre-painted galvalume aluminum zinc coating GI based trapezoidal steel sheet of any colour ,tensile strength of 550Mpa as in roof covering ,cladding to wall ,ridge, gutter etc fixed with self tapping screws as specified.

All as per item No.105 above but plain sheet for ridge ,gutter etc fixed with self tapping screws as specified.

Dismantling Structural steel work including door, gates, etc and similar works complete all as directed

S&F steel work in tubular truss or post of different size bend to shape, cut to length etc, including necessary welding, special shape washer, conforming to IS:1161-1998 grade St-240 complete as directed

Supply & Fix framed works such as grills grating etc with ends of bars shouldered and for riveted in forged into spikes, framed guard bars, railing and similar work confirming to Fe-410-0 or Fe 310-0 complete all as specified and directed

Checking of joinery (wooden/steel) iron/aluminum mongery, pelmet box, door springs etc requiring carpentry work and carrying out minor repairs such as tightening of screws/nails, fixing glass panes, minor adjustment of joinery, door etc. including petty repairs material like screws/nails, plug etc. to make it functional complete all as specified and directed. (Note: Any items required to be replaced shall be paid under respective items).

Taking down plaster, plaster work for patches, tiling work, filling of cement mortar in holes, joints, joinery (wooden/steel) iron/aluminum, pelmet box, etc requiring masonary work and carrying out minor repairs such as patches plaster, tiles, brick, filling etc. including petty repairs material like cement, sand, aggregate, tiles etc. to make it functional complete all as specified and directed. (Note: Any items required to be replaced shall be paid under respective items of Sch 'A'/BoQ).

Repair windows like steel/wooden/aluminum by using wire mesh and easing windows shutter by using oil,greesing or cleaning cement mortar or removing old rust, dust, mud etc make it good and smooth to openable in a normal process all as specified and directed.

M&L Vitrified Ceramic tiles 10 mm thick (square/ rectangular) light shade, polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6 all as specified and directed.

All as per item No 113 above but in skirting over 10mm thick screeding in cement mortar 1:4 all as specified and directed.

M&L for Paved tiles of size 300 x 300 x 08 to 10 mm thick with grey cement and pigment, set and jointed and pointed in neat cement slurry in floors laid over & including 15 mm thick screed bed in cement mortar 1:6 all as specified and as directed.

M&L for Chequered cement concrete tiles of size 300 x 300 x 25 mm thick with grey cement and pigment, set and jointed and pointed in neat cement slurry in floors laid over & including 15 mm thick screed bed in cement mortar 1:6 all as specified and as directed.

M/L Granite (of any type) tiles 16 to 18 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over 15mm thick screed bed in CM 1:6 as in cooking platform.

M&L 16 to 18 mm thick Granite (of any type) tiles machine cut, in skirting/ dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over 10mm thick screed bed in CM 1:4.all as specified and directed.

M&L Marble work 16 to 18mm thick (table rubbed and polished) in steps, jambs, pillars, windowsills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade all as specified and directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick over 20mm the cement screed base in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for Machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado over 10mm the cement screed base in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for treating the kota stone surface with beeswax polishing complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thick above or below ground level all as directed.

M&L 75 mm thick PCC 1: 3:6 type C2 using 20mm graded agg finishing even and smooth without using extra cement as in plinth protections/path and laid fair in alternate bays n including filler joints with sealing compound grade 'A' where required complete all as specified and as directed.

M&L 40 mm thick, Cement concrete, type B-1, (1:2:4), 20 mm graded aggregate as in floor making finished even and smooth using extra cement.all as specified and directed.

M&L for PCC 1:2:4 (using 12.5mm graded aggr) in roof Kerbs, rounded or chamfered or haunching in chajjas to prevent water seepage into brick walls, including necessary formwork and scaffolding up to a height of 8mtr including demolition of existing PCC all as specified and directed.

Taking down existing aluminum shutter of area exc 1.0 Sqm but not exc 2.00 Sqm and refixing the same in the same opening after repairing and make functional including replacement of fitting and fixture for proper functioning as required all as specified and as directed.

S & F In repairs Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminum alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty all as specified and directed

S & F in repairs Aluminum (extruded section body type )door closer hydraulically regulated designation No 3, universal type , suitable for door shutter of 851 to 1000 mm in width and of weight and weight between 61 to 80 kg ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and directed Make : Hardwyn/ Everite (All ISI marked)

S&F Anodised aluminum frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F Anodised aluminum window (two/three track) sliding type without sash bar and ventilator shutters ((lower type),aluminum section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodized aluminum snap beading, screws etc.complete all as specified and directed.

S&F Anodised aluminum door shutter aluminum section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 02 Nos in each door , hinges ,anodized aluminum snap beading, screws etc.complete all as specified and directed.

S&F 4 mm thick heat absorbing glass of any size with aluminum bedding and complete all as specified and directed.

Checking and attending to water leakage from taps, flushing cisterns, wash hand basins and other sanitary fittings/fixtures and any obstruction to water supply, requiring plumber work and carryout minor repairs such as replacement of washers, check nuts, tightening of fittings of flushing cistern etc including petty materials like washers of all sizes, thread(shoot), M-seal, screws, nails to make water supply/ plumbing lines functional and leak proof complete all as specified and directed. (Note: Major items required to be replaced shall be paid under respective items).

Supply and fix, as in repair,15 mm bore pillar tap, fancy type cast copper alloy, with quarter turn head, chromium plated, screwed down high pressure, with or without letter Hot or Cold with long screwed shanuls and fly nuts, screwed for iron pipe or for brass ferrule all as specified and directed.

Supply and fix, as in repair, 15 mm bore bib taps, cast copper alloy,cromium plated, fancy type, with quarter turn handle, screwed down, screwed for iron pipe or for brass ferrule all as specified and directed.

Supply and fix, as in repair, bib tap standard of PTMT any colour screwed, for iron pipe 15mm bore (minimum weight 90 gms) all as specified and directed.

S&F in repairs kitchen plate rack made out of stainless steel 0.63 mm thick sheet with partitions and size of rack 800 x 250 x 900 mm with shape and pattern as per sample kept in Sample room of GE Office complete all as specified and directed. Nirali /Anjali/Prayag/Bluestar

Supply and fix, as in repairs, sheet glass self assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long all as specified and directed.

S&F in repair brass chromium plated towel rail 600 mm long complete all as specified and directed.

S & F in repairs Toilet paper holder of brass chromium plated fixed to walls with chromium plated(CP) brass screws.

S&F in repair Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F in repair 15mm bore dia brass chromium plated wall mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F in repairs center hole basin mixer without pop-up waste system complete all as specified and directed. Make- Prayag or equivalent

S&F in repair Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) complete all as specified and directed.

Supply and fix, as in repair, stop valve, cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type) screwed down high pressure, with crutch or butterfly handles for 15 mm bore pipe or for unions all as specified and directed. Make: ECCO/Hindware/Parryware (All ISI marked)

S&F in repairs stop cock cast copper alloy, fancy type ,chromium plated, screwed down, high pressure, with crutch of butterfly handle screwed both ends to iron pipe of size 15mm, all as specified and directed. Make: ECCO/Hindware/Parryware (All ISI marked)

S&F in repairs angle cock 15mm bore, two way, chromium plated, fixed to GI or steel tubing incl fittings complete all as specified and directed. Make: ECCO/Hindware/Parryware (All ISI marked)

Supply and fix, as in repair, vitreous china wash basin, white, flat back size 580 x 450 mm, excluding taps, waste chain, plug and porcelain stopper but including brackets, cutting for and pinning in ends of bracket or erecting stand complete all as specified and directed.

Supply and fix, as in repair, sinks with drainage board made out of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortor to dwarf wall or including fixing cantiriver lever brackets and connecting union to pipe overall size 915mmX460mm and bowl size 410mmX330mmX160mm all as specified and directed. Make - Nirali /Anjali/Prayag/Bluestar.

Supply and fix, as in repair, waste coupling CP 32 mm dia for glazed ware basins etc with fly nuts flanged etc complete all as specified and directed.

Supply and fix, as in repair, 32 mm dia PTMT 610 mm long waste pipe suitable for WHB complete all as specified and directed.

Supply and fix, as in repair, CP 40mm dia waste coupling with inlet and out let screwed for pipe or connections including packing, union and cap etc complete all as specified and directed.

Supply and fix, as in repair, 40 mm dia PVC 610 mm long waste pipe suitable for complete all as specified and directed.

Supply and fix, as in repair, Overhead Shower 100 mm Round / Square Shape Single Flow (Brass Chromium Plated) with Rubit Cleaning System, including fixing to steel pipe or union of 15mm bore all as specified and directed. Make: ECCO/Hindware/Parryware (All ISI marked)

Taking up or down 15 mm bore old steel tubing and connections, including disconnection of fittings from tubing including cleaning for re-fixing or removal from site complete all as specified and directed.

All as per item No 157 here in before but 20 mm bore.

S&F of 15 mm bore tubes medium grade galvanized with and incl all GI fitting (such as bends, elbows, Tees, connectors, short pieces, back nuts, unions, caps and plug etc ) and fixed complete to wall and ceiling or laid in/on floor complete all as specified and directed,

All as per item No 159 here in before but 20 mm bore.

Supply and fix, as in repairs, 75 mm dia of outlet PVC(SWR) floor trap, plain with stainless steel grating including jointing with solvent cement all as specified and directed

Material and labour for preparation of new and previously un-treated wood and wood base surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer all as specified and directed.

S & F for Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminum alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed. Make : Hardwyn/Everite (All ISI Marked)

S & F for Pressed steel frames for doors size 105 x 60mm, 1.25mm thick with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed.

S & F for Pressed steel frames for doors size 125 x 60mm, 1.25mm thick with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed.

M&L preparation of new steel surface and applying two coats of synthetic enamel paint over one coats of Zinch chromate primer including preparation of new surfaces over 10 cm width on girth all as specified and directed.

Chinmay Traders

M/S SINGH FURNITURE MART

Shree Krishna Traders