Maintenance of feed mixing plant room and storage Go-down at CLF Debipur under Sepahijala District (2nd Call)

Demolishing cement concrete manually / by mechanical means including disposal of material with all lifts and up to 50 m lead etc. complete as per direction of the Engineer- in-charge:-

Dismantling GS sheet roofing including ridges, hips, valleys, gutters wind ties etc. including dismembering and stacking of serviceable materials and unserviceable materials separately with all lifts and upto a lead of 50 m etc. complete as per direction of the Engineer- in-charge.

Dismantling steel work in built up section in channels, angles, tees, flats including all gusset plates, bolts, nuts, cutting rivets, welding including dismembering and stacking of serviceable materials and unserviceable materials separately with all lifts and up to a lead of 50 m etc. complete as per direction of the Engineer- in-charge.

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead : - Of area 3 sqm and below

Dismantling old plaster or pointing, raking out joints, cleaning and preparing the surface for re- plastering or re-pointing including disposal of rubbish to the dumping ground with all leads and lifts etc. complete as per direction of the Engineer- in- charge.

Providing wood work in frames of false ceiling, partitions etc. sawn and put up in position :

Providing and fixing plain Multipurpose Cement board (High Pressure steam cured) as per IS : 14862 : 2000 with suitable screws for fibre cement board in ceiling etc. complete (frame work to be paid separately) :

Providing and fixing plastic beading (50 mm in size) of approved quality as per direction of the Engineer-in-charge.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete. Fixed to openings /wooden frames with rawl plugs screws etc.

Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - -All work up to plinth level: 1:4:8( 1 Cement: 4 fine sand : 8graded well burnt brick aggregate 40 mm nominal size) For feed storage room

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement- -All work up to plinth level:

Providing and laying cement concrete 1:2:4 (1 cement: 2 fine sand : 4 graded well burnt brick aggregate) flooring finished with a floating coat of neat cement including cement slurry, rounding of edges and strips and cost of glass strips etc. complete.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. -Thermo-Mechanically Treated barsof grade Fe 500D or more

Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. - Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing ridges or hips of width 60 cm over all width plain G.S. sheet fixed with polymer coated J. or L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers including a coat of approved steel primer and two coats of approved paint complete.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 275mm long wire springs grade No.2 and M.S. top cover of required thickness for rolling shutters & with handles, hold fast including embedding in cement concrete of required grade required for fixing in position, all necessary fittings, including applying of approved steel primer etc. complete as required:-

First class brick work in superstructure above plinth level & upto floor-five level including cost of all materials as required complete:- In cement mortar 1:4 ( 1 cement : 4 fine sand ).

15 mm cement plaster on the rough side of single or half brick wall of mix: In cement mortar 1 : 4 ( 1 cement : 4 fine sand )

12 mm cement plaster of mix In cement mortar 1 : 4 ( 1 cement : 4 fine sand )

Neat cement punning

Applying priming coat - With ready mixed Pink or Grey primer of approved brand and manufacture on wood work ( hard & soft wood )

Painting with synthetic enamel paint of required colour of approved brand and manufacture on new work to give an even shade. -Two or more coats on new work

Applying a coat of mordant solution on G.S. sheet - With a solution made of 38 gms of copper acetate in litre of soft water

Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade - New work (two or more coats) including a coat of appropriate steel primer but excluding a coat of mordant solution

Distempering with dry distemper of approved brand and manufacture (two or more coats) of required shade on new work, over and including water thinnable priming coat to give an even shade. to give an even shade.

Finishing walls with textured exterior paint of required shade of approved brand and manufacture.

Hiring charge for vehicle Maruti Omni/Maruti Wagon R/ Maruti Eco etc. (Haltage and milege) will be recorded and signed by both the Engineer-in-charge and the agency.

Transportation charge for work supervision by Maruti Omni/Maruti Wagon R/ Maruti Eco (As needed time by the Engineer-in-charge the agency will arrange vehicle as mentioned above at his own cost and risk