Improvement of Existing Boat Landing Centre and Public Rain Shelter at Sipakuda in Puri District

TOTAL AMOUNT Without Taxes in Rs. P

TOTAL AMOUNT With Taxes in Rs. P

Setting up the piling gantry and connected equipment over each pile location, including cost of shifting, cost of all materials for (400 mm Dia Pile) piling gantry, labour, Labour cess & T& P required setting up the rig to alignment and correct dimensions as shown in the drawing and as directed by the Engineer-in-Charge.(Main Jetty, Approach Jetty, Finger Jetty)

Boring through all types of soils, boulders, hard starta and rocks etc.. for 400mm Dia vertical bored piles from the existing ground level 0 mCD to the founding level(-)10.0m CD of the piles, including bailing, flushing the bore bentonite with required density, chiselling, shifting of materials labour, Labour cess & T& P required etc. complete the work as per directed by the Engineer-In-charge.(Main Jetty, Approach Jetty, Finger Jetty) Note:-i) In case the soil stratum at the founding level is loose the Engineer or his representative may direct the contractor to carryout additional length of boring and payment shall be made accordingly. ii) The sample of bored materials of regular interval shall be collected and produced for the verification of the Engineer or his representative at no extra cost . in case any test reqiured by engineer in-charge, bored the samples so collected shall be referred to an authorized laboratory / agency identified by the Engineer , cost for testing shall be included in the quoted rate. engineer in-charge decision regarding founding level is final.`no claims in this regards are entertained. iii) Boring through all type of soil strata means soft soil, weathered rock, cemented sand, boulders and hard rock etc., iv) The boring in all type of soil measurement will be made on the basis of depth of boring from encountered soft soil level to founding/pile termination level. v) All the boring depths shall be jointly measured actually at site and Engineer in-charge decision is final.

Supplying and fabricating M.S.liners confirming to IS specifications of SAIL of specified thickness for required length with M.S. shoes of 0.5 m height using 6mm thick M.S. plates for bored vertical pile measured from cut off level of pile to the terminating level including supplying, cutting, rolling, bending, handling and welding cost, labours, Labour cess, materials, accessories,all taxes, hire and running charges of all machineries, royality, labour, material, T&P, conveyance charges, Port entry fees etc. all complete as per drawings and specification as directed by Engineer-In-charge.(Main Jetty, Approach Jetty, Finger Jetty, Compound Wall, Toilet, Ticket Counter, Kiosk) Note:- The stiffener shall be measured under this item.In case the soil strata found to be not good in the founding level of the liner, extra depth may be provided as per site condition.

Providing and laying reinforced cement concrete in concrete mix M35 for Cast in situ Pile using tremmie method up to cut off level excluding cost of steel reinforcements in position as per approved drawing and as directed by the Engineer-In-Charge including mixing, laying, consolidating, curing, including all labours, slings, shackles, supply of all labour,Labour cess material, transportation cost, hire and running charges of all machineries such as cranes, lorries etc., complete as directed by the Engineer-In-Charge.(Main Jetty, Approach Jetty, Finger Jetty, Compound Wall, Toilet, Ticket Counter, Kiosk)

Fabricating and placing in position of steel reinforcement TMT bars(Fe 550)confirming to IS 1786 specifications of SAIL/RINL/TISCON for all reinforced cement concrete including lifting hook, cutting, bending, tying with 16 gauge G.I. binding wire and welding to proper specifications wherever required including cost of steel and binding wire, cover blocks of 75mm dia in CC M35 mix, supply of with supply of all materials, labour, transportation, Labour cess ,T&P, all taxes, tollage, safety measures, port entry fees, etc. all complete as directed by the Engineer-In-Charge (Main Jetty, Approach Jetty, Finger Jetty, Compound Wall, Approach Road, Service Road, Parking Area, Paved Area, Toilet, Ticket Counter, Kiosk) Measurement of reinforcement will be made on lengthwise including hooks, if any, separately for different diameter as actually used in work, excluding overlaps, from the length so measured, the weight of reinforcement shall be calcuted in tonnes by multiplying the coefficient per unit length of bar as per code of the respective size of bars used on the basis of wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding & placing shall not be measured as the cost of these items has already been included in the analysis of rates for reinforcement as per rule in force

Construction of RCC Railing of M35 Grade Precast & Cast Insitu with 20mm nominal size aggregate, true to line and grade, tolerance of vertical RCC post not to exceed 1 in 500, center to center spacing between vertical post not to exceed 2000 mm, leaving adequate space between vertcal post for expansion, joint with supply of all materials, labour, transportation, Labour cess ,T&P, all taxes, tollage, safety measures, port entry fees, etc. all complete as directed by the Engineer-In-Charge as per approved drawings and technical specifications as directed by the Engineer-in-Charge. (Including cost of reinforcement, binding wire & Labour charge as per approved drawing.) for Approach Jetty

Chiseling/Breaking using suitable tools and equipments the top of pile concrete up to the receipt of dense concrete and dressing the pile head suitably so as to receive the form work for deck work , including breaking to the required level exposing the pile reinforcement to sufficient length as per approved drawing for embedding into the coping beam etc. including removal of concrete debris from the site, supply of all labour, material, transportation cost, hire and running charges of all machineries complete for 1000mm dia piles as directed by the Engineer-In-Charge.(Main Jetty, Approach Jetty, Finger Jetty) (Compound Wall, Toilet, Ticket Counter, Kiosk)

Rigid and smooth centering and shuttering for R.C.C. works for pilemuff, column, beam, slab,etc work including false works and dismantaling them after casting with cost, conveyance, taxes of all materials, labour, labour cess, T&P etc. required to complete the work in all respect as per specification and directon of Engineer in Charge. (Main Jetty, Approach Jetty, Finger Jetty, Compound Wall, Toilet, Ticket Counter, Kiosk)

Rigid and smooth centering and shuttering for R.C.C. works for railing column for jetty work including false works and dismantaling them after casting with cost, conveyance, taxes of all materials, labour, labour cess, T&P etc. required to complete the work in all respect as per specification and directon of Engineer in Charge. ( Approach Jetty)

Rigid smooth centering and shuttering for R.C.C. works for slab,including false works and dismentalling then after casting with cost, conveyance, taxes of all materials, labour, labour cess, T&P etc. required to complete the work in all respect as per specification and directon of Engineer in Charge.. (Main Jetty, Approach Jetty, Finger Jetty, Compound Wall, Kiosk)

Providing and laying reinforced cement concrete in concrete mix M35 for Precast & Cast Insitu in Column, Beam, Slab, Staircase, Road & Parapet wall, excluding cost of steel reinforcements in position as per approved drawing and as directed by the Engineer-In-Charge including mixing, laying, consolidating, curing, including all labours, slings, shackles, supply of all labour,Labour cess, material, transportation cost, hire and running charges of all machineries such as cranes, lorries etc., complete as directed by the Engineer-In-Charge.(Main Jetty, Approach Jetty, Finger Jetty,Compound Wall, Approach Road, Service Road, Parking Area, Paved Area, Toilet, Ticket Counter, Kiosk)

Fabricating and placing in position of steel reinforcement TMT bars(Fe 550)confirming to IS 1786 specifications of SAIL/RINL/TISCON for all reinforced cement concrete pile cage including lifting hook, cutting, bending, tying with 16 gauge G.I. binding wire and welding to proper specifications wherever required including cost of steel and binding wire, cover blocks of 75mm dia in CC M35 mix, supply of with supply of all materials, labour, Labour cess transportation, T&P, all taxes, t

Supplying,fitting & fixing Kodappa tiles (0.10 to 0.40)sqm in floors, treads or steps and landing on 25mm thick bed of cement mortar (1:1) (1 cement, 1 sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles including cost, conveyance, taxes of all materials, scaffolding & staging charges with all labour, labour cess, T&P etc. required to complete the work in all respect as per specification and directon of Engineer in Charge. (Main Jetty, Approach Jetty, Finger Jetty)

Supply, fitting, fixing and laying of size 4 x 10 sqmm pvc insulated pvc sheathed armoured underground aluminium cable for working voltage of 1100 v in the existing PVC pipe including cost of materials, labour,Labour cess, T & P with all taxes and transportation charges as per specification and directon of Engineer in Charge. (Make-Havills, polycab or finolex) (Main Jetty, Approach Jetty, Finger Jetty)

Supply and laying in trenches of 75 mm HDP pipe PN 6.0 confirming to IS 4984-1995 in road cutting area for inserting the aluminium cable including cost, conveyance, royality & taxes of all materials with all labour, labour cess, T&P etc. required to complete the work in all respect as per specification and direction by the Engineer-in-charge.(Make-approved quality) (Main Jetty, Approach Jetty, Finger Jetty)

Supplying, fitting & fixing of 250mm nominal diameter x 350mm long P.V.C (ASTM) Pipes (Schedule-40) in outer surface of RCC Bollards including cost, conveyance, taxes, Labour, Labour Cess and T&P etc required to complete the work in all respect as per direction of the Engineer-in-Charge. (Main Jetty, Approach Jetty, Finger Jetty)

Cement concrete (1:2:4) with 12mm down hard granite chips for wearing coat over the roof slab including cost, conveyance, royality & taxes of all materials with all labour, labour cess, T&P etc. required to complete the work in all respect as per specification and direction by the Engineer-in-charge. (Main Jetty, Approach Jetty, Finger Jetty)

ollage, safety measures, port entry fees, etc. all complete as directed by the Engineer-In-Charge. (Main Jetty, Approach Jetty, Finger Jetty, Compound Wall, Toilet, Ticket Counter, Kiosk) Measurement of reinforcement will be made on lengthwise including hooks, if any, separately for different diameter as actually used in work, excluding overlaps, from the length so measured, the weight of reinforcement shall be calcuted in tonnes by multiplying the coefficient per unit length of bar as per code of the respective size of bars used on the basis of wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding & placing shall not be measured as the cost of these items has already been included in the analysis of rates for reinforcement as per rule in force

Supplying approved Marine ''D" hallow Rubber fender of size 150 x150 x25 mm as per specification and drawing including cost & taxes of Fender with transport charges to deliver at work site etc. complete in all respect as per the direction of the Engineer in charge. (Main Jetty, Approach Jetty, Finger Jetty)

Labour for cutting Marine ''D" hallow Rubber fender of required size and fitting &fixing the same as per specification and drawing along the jetty fender beam using stainless steel Anchore bolts, Nuts and washers of required size by drilling holes in the existing concrete surface and making good good of the damage with cement mortar(1:1) (1cement :1sand) including cost, conveyance, taxes of all materials labour, labour cess,T&P etc. required to complete the work in all respect as per drawing,design specification and direction of Engineer in charge (Excluding cost of Fender) (Main Jetty, Approach Jetty, Finger Jetty)

Supplying, fixing & fixing of 40 Watt LED solar mini mast street light .The Luminaire havee intigreted charge controller with LIFE P04 Battery (12.8v,18Ah) and 85 Wp PV module and Luminaries,8mtr cast iron pole (Design pole) single arm with panel box with instalation cost complete with connections testing and commissioning etcincluding cost, conveyance, taxes of all materials labour, labour cess,T&P etc. required to complete the work in all respect as per drawing,design specification and direction of Engineer in charge (Main Jetty, Approach Jetty, Finger Jetty)

Desiltation by dredging from the basin of Jetty using suitable type of dredger (-) 2.50 m RL including laying of Shore pipe lines as well as floating arrangements for disposing the dredged slurry, consisting of silt, sand and other hazardous materials present in the Jetty basin, 1.5 km away from the basin area. The rate shall include the cost of labour, materials, consumables, POL & other accessories required for running the dredger, tools & plants etc. including bunding in the island by providing coffer dam for retention of dredged solid materials as directed by the Engineer in Charge. (Basin Area)

Boring 300mm dia Pile upto 6m depth below ground level through all types of soil strata below ground level including cost, conveyance ,labour, labour cess, T&P and all other taxes etcrequired to complete the work in all respect as per direction of Engineer in Charge. (Compound Wall, Toilet, Ticket Counter, Kiosk)

Excavation of foundation in ordinary soil within 50m initial lead and 1.5m initial lift including rough dressing and breaking clods to maximum 5cm to 7cm and laying in layers not exceeding 0.3m in depth including cost, conveyance ,labour, labour cess, T&P and all other taxes etc required to complete the work in all respect as per direction of Engineer in Charge. (Compound Wall, Toilet, Kiosk)

Quarrying, collecting, supplying, filling sand with all leads, lifts and delifts or by mechanical means including cost and conveyance of all materials including cost, conveyance ,labour, labour cess, T&P and all other taxes etc required to complete the work in all respect and spreading the same in layers not exceeding 0.30 mtr. depth for compaction as per direction of Engineer-in-Charge. (Approach Road, Compound Wall, Service Road, Parking Area, Paved Area, Toilet, Kiosk)

Cement concrete(1:3:6) with 40 mm size broken hard granite chips for R C C works including hoisting and laying with cost and conveyance of all materials including cost, conveyance ,labour, labour cess, T&P and all other taxes etc required to complete the work in all respect as per direction of Engineer-in-Charge. (Approach Road, Compound Wall, Service Road, Pa

rking Area, Paved Area, Toilet, Kiosk)

Brick work with fly ass Bricks 23cmx11cmx8cm having crushing strength not less than 75 kg/m2 with dimensional tolerence +8 percent in cement mortar (1:4) in superstructure.with cost and conveyance of all materials including cost, conveyance ,labour, labour cess, T&P and all other taxes etc required to complete the work in all respect as per direction of Engineer-in-Charge. (Compound Wall, Toilet, Kiosk, Tick Counter)

16 mm thick cement plaster in cement mortor (1:6) over Brick Masonary including cost and conveyance of all materials with all the taxes, royality, labour,labour cess T & P required for the work etc. complete as directed by the Engineer-in-charge. (Compound Wall, Toilet, Kiosk, Tick Counter)

Priming one coat with water bound cement primer including cost, conveyance, taxes of all materials, scaffolding & staging charges with all labour, labour cess, T&P etc. required to complete the work in all respect as per specification and directon of Engineer in Charge. (Main Jetty, Approach Jetty, Finger Jetty, Compound Wall, Toilet, Ticket Counter, Kiosk)

Finishing walls 2 coats with weather coat of approved shade on new work to give an even shade including cost, conveyance, taxes of all materials, scaffolding & staging charges with all labour, labour cess, T&P etc. required to complete the work in all respect as per specification and directon of Engineer in Charge. (Main Jetty, Approach Jetty, Finger Jetty) (Compound Wall, Toilet, Ticket Counter, Kiosk)

Supplying, fitting and fixing of stainless steel of 304 grade Main gate of 2 mm thick as per aproved design , drawing and specification, buffing, polishing etc with cost, conveyance, taxes of all materials, labour, labour cess T&P etc. required for the complete in all respect as per direction of Engineer-in-charge.(For Main gate)

Rigid and smooth centering and shuttering for R.C.C. works for work including false and dismantaling them after casting with cost, conveyance, taxes of all materials, labour, labour cess, T&P etc. required to complete the work in all respect as per specification and directon of Engineer in Charge (Approach Road, service Road, Paved Area, Parking area, Toilet, Ticket Counter)

Quarrying, collecting and supplying good moorum from approved quarry with all leads, lifts and delifts including cost, conveyance, royality taxes of all materials etc. complete and spreading the same in layers not exceeding 22.5cm and consolidation with PRR including watering etc. complete With all leads, lifts and delifts labour, labour cess, T&P etc. required to complete the work in all respect as per specification and directon of Engineer in Charge (Approach Road, Service Road, Parking Area, Paved area, Toilet, Kiosk)

Finishing wall sursaface of walls with cement based wall puty (Water based) of approved make and finished smooth and even surface to received painting including cost of scaffolding staging charges with cost, conveyance, taxes of all materials, labour, labour cess, T&P etc. required to complete the work in all respect as per specification and directon of Engineer in Charge (Waiting Hall, Ticket Counter, Kiosk)

Wall painting 2 coats with plastic emulsion paint of approved shade to give an even shade including cost, conveyance, taxes of all materials, scaffolding & staging charges with all labour, labour cess, T&P etc. required to complete the work in all respect as per specification and directon of Engineer in Charge. (Waiting hall, Ticket Counter, Kiosk)

Supplying,fitting &fixing Ceramic Wall tiles in walls,skirting and risers of step on 12mm thick bed of cement mortar (1:3) jointed with neat cement slurry mixed with pigment to match the shade of the tiles including all labour, labour cess, T&P etc. required to complete the work in all respect as per specification and directon of Engineer in Charge. (Toilet, Ticket Counter)

Fixing special plain/printed series ceramic floor floor tiles of size 30cmx30cm of premium grade having thickness 7mm to 8mm confirming to IS 13755 in floors on 25mm thick bed of cement mortar (1:1) (1 cement, 1sand) jointed with neat white cement slurry mixed with pigment to match the shade of the tilesall labour, labour cess, T&P etc. required to complete the work in all respect as per specification and directon of Engineer in Charge. (Toilet)

Supplying, fitting & fixing of M.S. Grill for doors ,Windows & Ventilators of approved design including cost,conveyance, fabrication charges,all labour, labour cess, T&P etc. required to complete the work in all respect as per specification and directon of Engineer in Charge.. (Toilet)

Providing, fitting and fixing of Al. door with anodized Aluminium section No 9202 as vertical member, 9201 as top member and 9200 as bottom member with frame section as 9221 and 12 mm thick plain glass of approved quality fixed on door frame by means tapered clip No 4660 and the frame to be completed by means of jointing angle No 1855 etc including all cost of labour,labour cess. T & P, hire charges of drilling machine, labour charges etc complete as per direction of Engineer in charge. (Toilet, Ticket Counter)

Rigid and smooth centering and shuttering for R.C.C. work including false works and dismantaling them after casting with cost, conveyance, taxes of all materials, labour, labour cess, T&P etc. required to complete the work in all respect as per specification and directon of Engineer in Charge. (Ticket Counter)

Providing fitting and fixing of false ceiling with 12mm thick of approved gypsom/lafarge board, Aluminium anodised T Section No.3215 with 2'-0'' centre to centre, L Section No.1705 upto 15 micron on 4 walls to be fixed by means of steel screw and PVC plug and the Aluminium grid 2'-0''x2'-0'' suspended from ceiling etc complete in all respect including cost, conveyance, taxes of all materials and labour,labour cess T&P etc as per direction of Engineer in charge. (Ticket Counter)

Supply and fixing vitrified tiles (600mmx600mm)in floor treads or steps laying on 25mm thick bed of cement mortar 1 : 1 (1 cement : 1 sand)jointed with neat cement slurry(white cement)mixed with pigment to match the shade of tiles with cost of All materials and labour, labour cess charges etc.complete in all respect as per direction of Engineer-in-charge. (Ticket Counter, Kiosk)

Supplying, fitting & fixing 125x200 mm size roof tiles on 25mm thick bed of cement mortar (1:1) (1 cement, 1 sand) jointed with neat white cement slurry mixed with pigment to match the shade of the tiles including cost, conveyance,royalty, all taxes,labour, labour cess, T&P etc. complete as directed by the Engineer-in-Charge. (Ticket Counter)

Providing, fitting and fixing up 10 mm plain glass of width 0.3m over the walls and supported on the steel stand in ticket counter as per direction of Engineer in charge. (Ticket Counter)

Providing, fitting and fixing up partition walling aluminium anodized section No 9210 as single groov & double groov respectively as horizontal & vertical members and section4660 as tappered cvlipand jointing angleNo 1855 etc as per direction of Engineer in charge including cost of 10 mm Plain glass. (Ticket Counter)

Supplying all materials, labour, tools and plant and setting up boring equipments including erection of suitable staging for installation of the required size of tubewell, dismantling and removing the same after completion of the work, includifng transportation of the boring equipments, cleaning and levelling the site, excavation of mud pit, channels etc. levelling of site all complete as per direction of Engineer-in-charge

Supplying all labour, tools and plants and transporting boring pipes, top casing, grouting pipes, PVC pipes and fittings, PVC well screens, cement bentonite and gravels etc to work sites including loading and unloading etc. complete as per the direction of the Engineer-in-charge

Supplying all labour, tools and plants and drilling pilot bore not less than 102 mm dia without casing pipes in all kinds of soils for the following depths excluding supply of necessary cutting equipments, extra sockets (whenever required) etc and withdrawing the boring pipes, washing and keeping the bore clear for logging if required all complete as per the direction of Engineer-incharge

Supplying all required labour for logging the bore through departmental logging team (till logging team arrives at the site, the contractor is to keep the bore intact by circulating mud through the mud circulating system) and when the logging team arrives at the site, the contractor will withdraw the boring pipe with cutter etc. and keep the bore suitable for loggifng and supply required labour to carry out the logging operation

Supplying all labour, tools land plant and reaming the pilot bore to the following sizes and depths without casing pipes including withdrawing the boring pipes, washing the bore by means of pipe cylinder etc all complete as per direction of Engineer-in-charge (Reaming from 100 mm to 150 mm dia, 0 mtr to 300 mtr)

Reaming from 150 mm to 200 mm dia, 0 mtr to 300 mtr

Reaming from 200 mm to 250 mm dia, 0 mtr to 30 mtr

Supplying, fitting and fixing of stainless steel of 304 grade in grill fixing in wall at window level using 25 mm x 25 mm of 2 mm thick square pipe with stell flat of 20mm x 3 mm along with balustrade of size 20 x 20 x 2 mm in rows .08 m c/c as per aproved design and specification, buffing, polishing etc with cost, conveyance, taxes of all materials, labour, T&P etc. required for the complete in all respect as per direction of Engineer-in-charge.(For fixed type grill) (Ticket Counter)

Supplying all labour, tools and plant and jointing materials and lowering the 300mm dia top casing pipes into the positioin and removing the same after use all complete as per direction of Engineer-in-Charge.

150 mm (Sch 80) ASTM pvc pipe

Supplying all labour, tools and plant and jointing materials and lowering the pvc casing pipes, fittings and well screens in position including fitting and fixing of centraliser, cutter plug and washing the bore etc complete as per direction of Engineer-in-Charge. (100 mm (Sch 80) ASTM pvc pipe including Stainer)

Supplying all labour, tools and plant and grouting with cement bentonite slurry for saline sealing in the bore around the 150mm dia pvc Casing pipe {Each bag cement (50 kg) added with 24 ltr of water and 1 to 2 kg bentonite powder will form 40ltrs of slurry (0.021 cum)} including cost of cement & Bentonite powder all complete as per the direction of the Engineer-in-Charge

Supplying all labour, tools and plant and packing the bore with washed gravel (size P-6) around the pipes in good quality excluding cost of gravel etc all complete as per the direction of the Engineer-in-charge (Up to 270 mtr)

Supplying all labour, tools and plant and grouting with cement slurry for sanitary

sealing in the bore around the upper most 3 metres of 150 mm dia PVC casing pipe {Each bag cement (50 kg) added with 24 ltr of water and 1 to 2 kg bentonite powder will form 40ltrs of slurry (0.021 cum)} including cost of cement & Bentonite powder all complete as per the direction of the Engineer-in-Chargee

Supplying all labour, tools and plant and materials for cleaning and developing the tubewell with compressor continuously washed till clean and adequate discharge is obtained from the tube well including supply and use of necessary equipments and labour complete in all respect as per the direction of the Engineer-in-Charge

Supply of all labour,Materials & T&P for 100 mm dia C.I plug cutter and fitted and fixed up in perfectly vertical position, including cutting and threading pipe and fixing all jointing materials etc. complete including cost and taxes of materialsas per the direction of the Engineer-in-Charge

Supply of all labour,Materials & T&P for 150 x 100 mm PVC R/S and fitted and fixed up in perfectly vertical position, including cutting and threading pipe and fixing all jointing materials etc. complete including cost and taxes of materialsas per the direction of the Engineer-in-Charge.

Providing and fixing 40mm dia Chlorinated Polyvinyl Chloride (CPVC) pipes conforming to IS 15778,having thermal stability for hot & cold water supply including all CPVC plain & brass threadedfittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching,refilling & testing of joints complete as per direction of Engineer- in-Charge

Provision for iron rolling shutter for Kiosk.