Construction of B-cum-C type residential building and allied works at Egra 220KV GIS Sub-Station under Kharagpur Area Office, WBSETCL

Construction of B-cum-C type residential building and allied works at Egra 220KV GIS Sub-Station under Kharagpur Area Office, WBSETCL

Percentage BoQ

BoQ_Ver3.0

NIT No.:- CE/(O&M)–II/EGRA/CIVIL/ 2025-26/31, DATED 30.12.2025

Bidder Name :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

Construction of B-cum-C type residential building and allied works at Egra 220KV GIS Sub-Station under Kharagpur Area Office, WBSETCL

a) Depth of exavation not exceeding 1.5m

b) Depth of exavation for additional depth beyond 1.5 m and upto 3.0 m not requiring shoring.

Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work)

a) in foundation trench or plinth (i)With earth obtained from excavation of foundation.

Filling in foundation or plinth by medium sand in layers not exceeding 150 mm. as directed and consolidating same by thorough saturation with water ramming complete, including the cost of supply of sand. (Payment to be made on measurement of finished quantity)

Labour for laying single brick flat soling including ramming and dressing bed to proper level and filling joints with powdered earth. (By using Departmental Brick)

Cement concrete with graded stone ballast (40 mm. size) excluding shuttering. In ground floor. A)Pakur Variety (a) 6:3:1 proportion.

Ordinary cement concrete Mix 4:2:1 with graded stone chips(20 mm.size) excluding shuttering and reinforcement, if any, as per relevant IS codes. a) Pakur Variety

a) Gr. Floor

b) 1st floor

c) 2nd floor

d) 3rd floor

Ordinary cement concrete Mix 3:1.5:1 with graded stone chips(20 mm.size) excluding shuttering and reinforcement, if any, as per relevant IS codes . a) Pakur Variety

a) Gr. Floor

b) 1st floor

c) 2nd floor

d) 3rd floor

125 mm. thick Flyash brick work as per IS 12894:2002 in cement mortar (1:4) in ground floor.

a) Gr. Floor

b) 1st floor

c) 2nd floor

d) 3rd floor

25mm. thick damp proof course with cement concrete with stone chips (3:1.5:1) [ with graded stone aggregate 10 mm nominal size ] and admixture of water proofing compound as per manufacturer's specification followed by over two coat of polymer based paint( 1st coat after 4 to 5 days of concrete laying and second coat just before brick masonry work) as directed ( the cost of water proofing compound & polymer based paint to be paid separately).

250 mm thick Brick work with Fly Ash Bricks (250mmx125mmx75mm) as per IS 12894:2002 in cement mortar (1:6)

(i) In foundation and plinth.

(ii) In superstructure, ground floor (6:1)

a) Gr. Floor

b) 1st floor

c) 2nd floor

d) 3rd floor

Hire and labour charges for shuttering with centring and necessary staging up to 4 m. using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams, columns, lintels curved or straight including fitting, fixing and striking out after completion of works.

(a) 25mm. to 30mm. shuttering without staging in foundation etc.

a) Gr. Floor

b) 1st floor

c) 2 nd floor

d) 3 rd floor

(b) Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete work

a) Gr. Floor

b) 1st floor

c) 2 nd floor

d) 3 rd floor

Supplying and laying Polythene Sheet (150gm/sq.m.) over damp proof course or below flooring or roof terracing or in foundation trenches.

Priming one coat on timber or plastered with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Neat cement punning about 1.5 mm. Thick in wall, dado, window, sills, floor, drain etc.

Supplying, fitting and fixing of 125mm long wooden buffer block With Sal : Siliguri.

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc. Including supply of rods, initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. A) For works in foundation, basement and up to roof up to 4m. (i) Tor steel/Mild steel TATA/SAIL/RINL

a) Gr. Floor

b) 1st floor

c) 2 nd floor

d) 3 rd floor

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints or roughening of concrete surface, including throating, nosing and drip course where necessary.

i)15mm thick (With 6:1 cement mortar) (Internal)

a) Gr. Floor

b) 1st floor

c) 2 nd floor

d) 3 rd floor

ii) 10 mm thick (With 4:1 cement mortar) (Internal)

a) Gr. Floor

b) 1st floor

c) 2 nd floor

d) 3 rd floor

iii) 20 mm thick (With 6:1 cement mortar) (External)

a) Gr. Floor

b) 1st floor

c) 2 nd floor

d) 3 rd floor

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary :

(a) On timber or plastered surface :

With super gloss ( hi- gloss )

(i) Two coats (with any shade except white).

(b) On steel or other metal surface :

With super gloss (hi-gloss) -

(i) Two coats (with any shade except white)

Labour for Chipping of concrete surface before taking up Plastering work.

Extra rate for using water proofing and plasticising admixture @ 0.2% by weight of cement (or at manufacturer's specified rate ). For Concrete of various grades.

Applying 2 coats of bonding agent with synthetic multi functional rubber emulsion having adhesive and water proofing properties by mixing with water in proportion (1 bonding agent : 4 water : 6 cement) as per Manufacture's specification.

Supplying and laying true to line and level vitrified tiles of approved brand (size not less than 600 mm X 600 mm X 10 mm thick) in floor, skirting etc. set in 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry back side of tiles using cement @ 2.91Kg./sqM or using polymerised adhesive (6 mm thick layer applied directly over finished artificial stone floor/Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per sqM below mortar only, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles / epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturer's specification and direction of Engineer-in-Charge.(White] cement, synthetic adhesive and grout material to be supplied by the contractor.

I) With application slurry @1.75 kg/ Sq.m, 20 mm sand cement mortar (1:4) & 2 mm thick cement slurry at back side of tiles, 0.2 kg/ Sq.m white cement for joint filling with pigment.

A) Light Colour

a) Gr. Floor

b) 1st floor

c) 2 nd floor

B) Deep colour

a) Gr. Floor

b) 1st floor

c) 2 nd floor

Supplying, fitting and fixing Marble Slab/tile of 15 to 18 mm thickness in floor, lobby, stair, landing & treads etc. over 20 mm (av.) thck base of Cement mortar (1:2) laid with white cement slurry @ 4.4 kg/Sq.m before placing marble & jointed with white cement slurry @ 2.0 kg/Sq.m with necessary pigments including grinding and Granite polishing as per direction of Engineering -in -Charge in Ground Floor. [White cement and Pigment to be supplied by the Agency]

(a) With Makrana plain pink / Adranga Pink / Garbh Gulabi / Udaypur pink / Udaypur Green / Black Bhaslana

i) Area of each Slab/tile exceeding 0.3 sq.m. but not exceeding 0.6 sq.m.

a) Gr. Floor

b) 1st floor

c) 2 nd floor

Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.

(i) Wall

With Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m.

(a) Area of each tile upto 0.09 Sq.m

(i) Coloured decorative

a) Gr. Floor

b) 1st floor

c) 2 nd floor

Applying Exterior grade Acrylic Emulsion primer of approved quality and brand on plaster or concrete surface old or new surface to received the decorative texture ( matt finish ) or smooth finish acrylic exterior emulsion paint including scraping and papering the surface throughly, complete as per manufacture`s specification and as per direction of the E.I.C. a) One coat.

a) Gr. Floor

b) 1st floor

c) 2nd floor

d) 3rd floor

Protective and decorative Acrylic exterior Emulsion paint of approved quality as per manufacture`s specification and as per direction of the E.I.C. to be applied over acrylic primer as required . The rate includes cost of materials, labour , scaffolding and all incidental charges but excluding the cost of primer. ( Two coats ).

i) Normal Acrylic Emulsion.

a) Gr. Floor

b) 1st floor

c) 2nd floor

d) 3rd floor

Acrylic distemper to interior wall , celling with a coat of solvent based interior grade acrylic primer ( as per manufacturers specification ) including cleaning and smoothing of surface. Two coats All floors

Rendering the surface of walls and ceiling with white cement based wall putty of approved make and brand(1.5mm thick)

Supplying fitting and fixing in position approved P.V.C. door frame ( matt finish ) made of extruded P.V.C. multichamber hollow section having dimensions 60mm x 50mm X 2 mm ( +/- 0.2 mm ) , horizontal section will be joined with vertical section by galvanised steel screws after inserting two number steel brackets as reinforcement making suitable space for placing hinges, one steel tube 40mm x 20mm x 1.20 mm will be inserted on one full vertical side of the frame (hinge side) as reinforcement, the frame will then be fixed in the opening with the help of P.V.C. expandable fastner wooden gutties and galvanised steel screws including cost of all materials and labour, hire charges of tools and appliances, carriage of all materials taxes and all other incidental charges complete. All Floor.

Supplying fitting and fixing P.V.C. door shutter of approved quality & shade in position, the style & rail of the P.V.C. door shutter will be made of rigid P.V.C. multicavity hollow chamber of suitable size and section with 2.0mm(+/_ 0.2 mm ) wall thickness, the section will have 2nos. built in heads, horizontal & vertical section shall be fixed to each other by self tapping screws and 2 nos. of solid plastic or M.S. tubular galvanised brackets of length 200mm x 80mm and other 100mm x 100mm both 1.20 mm in each corner of the shutter frame for placing hinges. Polymer based multicavity holoow section of 105mm X 37 mm with 2.0 mm ( +/- 0.2 mm ) wall thickness will be fitted in the middle as lock rail reinforced by solid polymer bar of 200 mm long at both ends & screws for both sides . The section frame will then be fitted in by pre panels of size100 mm X 20 mm wall thikness 1.2 mm ( +/- 0.2 mm ) and 2 nos. of 6mm dia bright rod will be inserted horizontally with both side check and nut system and stretches where fixing of hinges / hasp bolt / tower bolt / door ring are required to be strong enough to with stand wear and tear. The rate is inclusive of cost of all materials and labour hire of tools and plants and appliencies. Carriage of all materials taxes and all other incidental charges complete. The rate is exclusives of cost of hinges , hasp bolt, tower bolt, door ring etc.

i) 37mm thick shutter .

a) Gr. Floor

b) 1st floor

c) 2nd floor

M.S. gate of Jail type as per approved design made of strong M.S. frame work, intermediate stiffeners and round / square bars or angles. M.S. sheet (not less than 14 gauge) gussetes, cleats etc. including necessary riveting, bolting, welding, locking and hanging arrangements, fitting and fixing complete as per direction of the Engineer-in -charge.

a) In Gr. Floor

b) In 3rd Floor

Pre-Constructional Anti-termite measures: (a) Anti termite treatment to bottom surface ( in case of masonry foundation and basements) and the sides (upto a height of 300 mm. from bottom) of the excavation trenches with chemical emulsion by admixing chloropyrofos emulsifiable concentrates (1% concentration) with water by weight at the rate of 5 Litres per sq. m. area. The work shall be carried out as per specification described in 6.2.1. of code IS- 6313 (part -II) 1981. Mode of measurment will be the plan area of foundation treated.)

i) Ground Floor

Supplying, fitting and fixing windows and ventilators with or without integrated grills conforming to IS 1038-1975 and manufactured from rolled steel sections conforming to IS 7452-1974 with non-friction projecting type, box type hinges, glazing clips, lugs locking bracket, handle plate etc, including hoisting in position, straightening if required, fixing lugs in cement concrete ( 1:2:4) with stone chips 20 mm down cutting holes and mending good damages to match with existing surface complete in all respect excluding glazing

(i) M.S. integrated grill as per approved design integrated with steel window or ventilator, joints continuously welded with M.S. flats and bars.

a) Gr. Floor

b) 1st floor

c) 2nd floor

(ii) Top hung side hung ventilators as per IS sizes 580mm.

a) Gr. Floor

b) 1st floor

c) 2nd floor

(iii) Center hung ventilators as per I.S. sizes 580 mm.

a) Gr. Floor

b) 1st floor

c) 2nd floor

(iv) steel peg stay 300 mm long including fitting and fixing.

a) Gr. Floor

b) 1st floor

c) 2nd floor

Supplying fitting fixing fan hook for ceiling with 1 meter long 16 mm dia rod complete including mending damages.

Supplying , fitting and fixing M.S. clamp for door and window frame made of flat bent bar, end bifurcated, fixed in cement concrete with stone chips (4:2:1) fitted and fixed complete as per direction.

i) 40mm. X 6mm. 250mm. Length.

M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and Square bars of windows, railing etc. fitted and fixed with necessary screws and lugs . (i) Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr.

a) Gr. Floor

b) 1st floor

c) 2nd floor

Supplying, fitting and fixing UPVC pipes A - Type and fittings conforming to IS : 13592 - 1992 with all necessary clamps nails including making holes in walls, etc. and cutting trenches in any soil, through masonry concrete structure etc. if necessary and mending good damages including jointing with jointing materials (Spun yarn, valamoid / bitumen / M. seal etc.) complete.

A) UPVC pipes i) 110 mm dia

B) Bend 87.50 degree. i) 110 mm dia

C) Shoe i) 110 mm dia

D) Plain Y i) 110 mm dia

E) Plain Tee i) 110 mm dia

Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992

A) 125 X 110 S Trap W.C.ring 75 mm

B) Vent Cowl i) 110 mm dia

C) Pipe clip i) 110 mm dia

D) 110 X 110 P Trap 75 mm

E) Door Bend 110 mm (T.S)

F) Door tee

Wood work in door and window frame fitted and fixed complete icluding a protective coat of painting at the contact surface of the frame excluding cost of concrete , iron Butt hinges and M.S. clamps.

Sal :Local.

a) Gr. Floor

b) 1st floor

b) 3rd floor

Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hige and other fittings.

i) 35mm. Thick shutters with 19mm. Thick panel of 30 to 45 cm. Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak.

a) Gr. Floor

b) 1st Floor

c) 2nd floor

Wooden sash bar 50mm. X 35mm. Upto 1200 mm length with coach screw and flat iron clamps (40mm. X 5mm.) fitted and fixed complete in any position.

Sal : Local.

Anodished aluminium butt hinges of approved quality manufactured from extroded section conforming to IS 205/60 specification and fitted & fixed with cadmium plated screws.

(i) 75 x 45 x 2.5mm

(ii) 100 x 63 x 3.2mm

Iron socket bolt of approved quality fitted and fixed complete.

a) 225mm long x 10mm dia bolt.

b) 300mm long x 10mm dia bolt.

Brass hasp bolt of approved quality fitted and fixed complete (oxidised) with 16mm dia rod with centre bolt and round fitting. 300mm long.

Rebeated iron mortice lock (local best approved quality) 6 levers with handle, connected rods and keys consisting a complete set I.S.I mark :

(a) With anodised aluminium decorative handle.

Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987. i) 4mm thick coloured / tinted / smoke glass.

Renewing hinged cleat with old hinge and new screws.

(a) Local Sal.

Supplying best Indian figured glass viz.hammered, fluted, ribbed, pinhead etc., type including cutting to required sizes, setting on putty bases and fitted and fixed with nails and putty complete in all floors and upto 6 mtr height for external wall. : i) 3 mm thick ( coloured )

a) Gr. Floor

b) 1st Floor

c) 2nd floor

Extra for fixing glass panes in steel window.

Supplying, fitting and fixing C.I. square jalli.

Applying 2 coats of Non- Toxic Acrylic Polymer modified paint having adesive & water proffing properties by mixing in proportion [ 1 liquid : 4 cementitious materials ] or as per manufacturer`s specification for water proofing layer in water tank .

R.C. shelves (1:1.5:3) either precast or cast in situ with stone chips and necessary reinforcement upto 1% (0.8% main and 0.2% distribution bars), shuttering etc. and 6 mm. thick cement plaster (4:1) including neat cement finishing and cutting chase fitting and fixing in position, mending good damages as necessary complete.(i) For 50 mm. Thick panels. (TATA/SAIL/RINL)

a) Gr. Floor

b) 1st Floor

c) 2nd floor

Supplying, fitting and fixing Black stone slab use in kitchen slab, alcove, wardrobe etc. laid and jointed with necessary adhesive cement mortar (1:2) including grinding or polishing as per direction of Engineer in Charge in ground floor. Slab thickness above 25 mm and upto 37.5 mm.

a) Gr. Floor

b) 1st Floor

c) 2nd floor

18 mm. to 22 mm. thick, kota stone slab set in 20 mm thick (avg) cement mortar (1:4) in floor, stair & lobby including pointing in cement slurry with admixture of pigment matching the stone shade, including grinding & polishing as per direction of Engineer - in - charge to match with the existing work. [Slurry for bedding @ 4.4 Kg/Sq.m and pointing @2.0 Kg/Sq.m]

a) Gr. Floor

b) 1st Floor

c) 2nd floor

Extra cost of labour for prefinished and premoulded Nosing to treads of steps, railing, window sill etc. of Kota Stone.

75 mm. Thick Flyash brick work as per IS 12894:2002 cement, sand mortar (1:3) in ground floor including H.B. netting in every alternate layers.

a) Gr. Floor

b) 1st Floor

c) 2nd floor

Extra for using approved H.B netting in every third layer in 125 mm thick brickwork in any floor.

Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete: a) With continuous plate base (Hexagonal/ Round rod)

(i) 75 mm grip x 10mm dia rod.

(ii) 150mm grip x 12mm dia rod.

Supplying, fitting and fixing PVC pipes of approved make of (medium duty) conforming to ASTMD- 1785 and threaded to match with GI pipes as per IS : 1239 (part - I ) .With all necessary accessories ,specials viz et, bend, tee, union, cross, elbow, nipple, longscrew, reducing socket, reducing tee,short piece etc. fitted with holder bats clamps,including cutting pipes , making threads , fitting, fixing etc. complete in all respect including cost of all necessary fittings as required, jionting materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measuremnts of total pipe line including all specials. No separate payment will be made for accesories, specials . Payment for painting will be made separately)

a) For concealed Work PVC Pipes 15 mm dia.

b) For concealed Work PVC Pipes 20 mm dia.

c) For exposed Work PVC Pipes 25 mm dia.

d) For Exposed Work PVC Pipes 32mm dia.

e) For Exposed Work PVC Pipes 40 mm dia.

f) For Exposed Work PVC Pipes 50 mm dia.

Supplying, fitting and fixing gunmetal wheel valve of approved brand and make tested to 21 kg per sq. cm. (for water lines only).

(iii) 32 mm

Supplying,fitting and fixing G.I. pipes of TATA make with all necessaryaccessories,specials viz socket,bend,tee,union, cross, elbo, nipple,longscrew ,reducing socket,reducing tee,short piece etc. fitted with holder bats clamps,including cutting pipes,making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground.(Payment will be made on the centre line measuremnts of total pipeline inclding all specials.No seperate payment will be made for accesories,specials) Payment for painting will be made separately.

(i) 40 mm dia. medium quality

(ii) 50 mm dia. medium quality

Supplying , fitting and fixing of long screw(150 mm long) of TATA make with sockets(TATA make) & jamnut.

(iii) 40 mm

Supplying , fitting and fixing of G.I. plug.

(iii) 25 mm

Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc.

Supplying,fitting and fixing 32 mm dia. Polythene flush pipe of approved make with necessary fixing materials and clamps complete.

Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc.

i) With 'P' trap

Supplying,fitting and fixing approved brand P.V.C.CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia.

(i) 450 mm long

Supplying , fitting and fixing of chromiun plated stop Cock ( Equivalent to Code No. 513 (A ) & 513 (B) & Model - Tropical / Sumthing special of ESSCO or similar Brand.

Supplying , fitting and fixing of chromiun plated concealed stop Cock ( Equivalent to Code No. 514 (A ) & Model - Tropical / Sumthing special of ESSCO or similar Brand.

Supplying , fitting and fixing of chromiun plated angular stop Cock with wall flange ( Equivalent to Code No. 5053 & Model - Florentine of Jaquar or similar Brand.

Supplying , fitting and fixing of chromiun plated Bib Cock with wall flange body ( Equivalent to Code No.5047 & Model - Florentine of Jaquar or similar brand.

Supplying,fitting and fixing approved brand 32 mm dia P.V.C. waste pipe, with P.V.C. coupling at one end fitted with necessary clamps.

(i) 600 mm long

Supplying, fitting and fixing shower rose of approved brand and make.

a) Chromium plated round shower with revolving joint ( Equivalent to code no . 541 (N) & Model - Tropical / Sumthing special of ESSCO or similar Brand).

Supplying fitting and fixing of High Density polyethylene pipe conforming to IS - 4984 - 1985 (Dia) [PE-63]

A. 10Kg/ Sq.Cm (Dia) (Working Pressure)

Supplying, fitting, fixing PVC Tee conforming to ASTMD - 1785 and threaded to match with GI pipes as per IS : 1239 ( Part - I ).

a) Tee 32 mm dia

Supplying, fitting, fixing PVC Bend conforming to ASTMD - 1785 and threaded to match with GI pipes as per IS : 1239 (Part - I)

a) Long Bend (90 Degree) 32 mm dia

Polythene Bib Cock / Stop Cock with plastic inlet (EMCO/ ATLAS or equivalent ) i) 15 mm

Supplying , fitting and fixing towel rail with two brackets.

(a) C.P over Brass

(i) 25mm dia and 750 mm long

(ii) 25mm dia and 450 mm long

Supplying,fitting and fixing white vitreous china best quality approved make wash basin with C.I. brackets on 75 mm X 75 mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillar cock of 15 mm dia., C.P. chain with rubber plug of 30 mm dia., approved quality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approved quality P.V.C. connection pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint.

(i) 550 mm X 400 mm size

Supplying , fitting and fixing glass shelf with aluminium guard rails. a) ordinary type with 5.5 mm sheet glass. i) 600mm X 125 mm

Supplying,fitting and fixing best quality Indian make mirror 5.5 mm thick silver red as per I.S.I specifications supported on fibre glass frame of any colour , frame size 550mm X 400 mm.

Construction of circular soak well 2.5 metre deep in all types of sandy soils with dry brick work upto 1.6 metre from the bottom having 150 mm intermediate cement brick work (6:1) band all round and cement brick work (6:1) upto 0.90 metre from top with 19 mm thick cement plastering (4:1) to inside face upto the depth of cement brick work, 12 mm thick cement plaster (4:1) on outer face from top of the well upto G.L. and 6 mm thick cement plaster (4:1) on top of the R.C.C. cover slab including filling bottom 1.00 metre of inside of the well with brick metal (50 mm to 63 mm size) including R.C.C. cover slab of designed thickness with cement concrete (4:2:1) with stone chips with necessary reinforcement and shuttering including one 560 mm dia. R.C.C. manhole cover of approved make supplied, fitted and fixed in the cover slab with necessary fittings, making nacessary arrangements for pipe connections, excavation of well including shoring, dewatering and removing the exess earth from the premises as per direction complete in all respect with all costs of labour and materials.

Supply of PVC pipes & fittings Schedule 80 (medium duty) conforming to ASTMD - 1785 &threaded to match with GI pipes as per IS : 1239(Part - I) (a) Reducing socket

(ii) 25 X 20 mm

(iii) 32 X 25 mm

Constructing Inspection pit of inside measurement 600mm X 600mm X upto 600mm (depth) with 250 mm thick 1st. class brick work in cement mortar(6:1) on all sides, bottom of the pit consisting of 100 mm thick cement concrete (6:3:1) with jhama khoa over a layer of jhama brick flat soling,12 mm thick (4:1) cement plaster to inside walls and out-side walls upto G.L. and 19 mm.thick (4:1) plaster to bottom of the pit, providing necessary invert with cement concrete (4:2:1) with jhama chips as per direction, neat cement finishing to entire internal surfaces, top of the pit covered with 100 mm thick R.C.C. slab (4:2:1) with stone chips and necessary reinforcements upto 1% and shuttering including 6 mm thick cement plaster (4:1) in all external surfaces of the slab and one 560 mm dia. R.C.C. manhole cover of approved make supplied, fitted and fixed in the slab with necessary fittings, necessary earthwork in excavation in all sorts of soil, filling sides of the pit with earth and removing spoils after work complete in all respect with all costs of labour and materials.

(i) With pakur variety (SAIL/TATA/RINL)

Construction of septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar(4:1) including two 560 mm dia R.C.C manhole cover ( heavy type ) of approved make supplied , fitted and fixed in the 100 mm thick R.C.C ( 1:1.5:3) top slab with necessary reinforcement (cost of shuttering included) , 20 mm thick cement plaster (4:1) with neat cement finish to internal surfaces and 15 mm thick cement plaster (4:1) to out side wall upto 200 mm below G.L floor finished with 25 mm thick grey artificial stone over 100 mm thick R.C.C (1:1.5:3 ) bottom slab including supplying , fitting and fixing all necessary specials, fittings,S.W. tees, C.I. foot rest etc. including excavating earth in all sorts of soil,shoring,bailing and pumping out water as necessary,ramming,dressing the bed and refilling the sides of the tank with earth,removing spoils, filling up the chamber with clear water, removing foreign materials from the chamber and including constructing attached inspection pit as per approved drawing and connecting all necessary pipes,joints etc. with internal plaster work and A.S.F is to be done with admixture of water proofing compound @0.5 % by weight of cement with all costs of labour and materials.

(i) For 50 users with pakur variety (SAIL/TATA/RINL)

Supplying, fitting and fixing soap holder

PTMT (Prayag or equivalent)

Supplying P.V.C. water storage tank of approved quality with closed top with lid (Black) - Multilayer

(a) 1500 litre capacity

Supplying, fitting and fixing stainless steel sink complete with waste fittings and two coats of painting of C.I. brackets.

i) 530 mm X 430mm X 180 mm

Labour for punching hole in plastic water storage tank upto 50 mm dia.

Labour for hoisting plastic water storage tank.

a) Upto 1500 litre capacity.

Upto 3rd story from G.L.

Supply of Chlorinated Polyvinyl Chloride (CPVC) pipes & fittings conforming to IS-15778: 2007

(i) Ball Valve

(ii) Male threaded adaptor (brass threaded)

(iii) Female threaded adaptor (brass threaded)

(iv) Female Elbow (brass threaded)

a) 20 mm X 15 mm

b) 25 mm X15 mm

(v) Male Elbow (brass threaded)

a) 20 mm X 15 mm

b) 25 mm X15 mm

(vi) Female Tee (brass threaded)

a) 20 mm X 15 mm

b) 25 mm X15 mm

Supplying profiles of required section made of Aluminium Alloy Extrusions conforming to IS: 732-1983 and IS: 1285- 1975; Annodized (with required film thickness and specified colour / natural) matt finished conforming to IS: 1868-1983 for fabrication of composite door, sliding & casement windows, partitions, formed of basic sections of any ISI embossed / certified make and brand as per direction of Engineer - In- Charge. (Payment will be made on finished length of the work).

(A) In 10-12 Micron thickness Annodizing film, (I) Natural White

(a) 3 Track Sliding Window

(i) Bottom Frame

(ii) Top and Side Frame

(b) Shutter for all track sliding window

(i) Bottom & Top Member

(ii) Style Side Member

(iii) Interlocking Member

(iv) Fixed glazing. (a) Glazing Clip

(v) Supplying maruti lock (100mm)

(vi) Supplying PVC rollers for sliding windows as per direction of Engineer in charge.

Supplying EPDM gusket of approved make and brand as per direction of Engineer in charge.

i) For sliding windows

a) 'T' shaped EPDM gasket for frames

b) 'U' shaped EPDM gasket for frames

Labour charge for fabrication and installation of composite door, window, partitions made from annodized extruded alloy aluminium sections for the following units:-

(A) Glazed aluminium sliding windows made of extruded and annodized alloy aluminium sectios, fabrications, including cutting to proper shape and size, drilling and aligning of window shutter frame fitted with in built locking arrangements, sliding rollers and other necessary fittings, fixture, adhesives and joineries along with extruded neoprine or EPDM gasketing in between window frame and masonry work (walls, column, beam.lintels etc.) as well as between glass and shutter frame for fixing glass and Poly Shulphate sealant and in between shutter and window frame where necessary including cutting to requisite size and fixing glass as per drawing, specification and direction of EIC. The rate includes the hire charge of all tools and plants, including all incidental charges, adhesive, joineries such as screw, cleate angle etc. but excluded the cost of extruded aluminium sections, glass, neoprene / EPDM gasketing, locking arrangement and rollers.

i) 3 track sliding window.

Supplying solid flush type doors of commercial quality, the timber frame consisting of top and bottom rails and side styles of well seasoned timber 65mm wide each and the entire frame fitted with 37.5mm wide battens places both ways in order to make the door of solid core and internal lipping with Garjan or similar wood veneers using phenol formaldehyde as glue etc. complete, including fitting, fixing shutters in position but excluding the cost of hinges and other fittings (i) 35 mm thick shutters (single leaf). a) In ground floor.

b) 1st floor

c) 2nd floor

Supplying fitting, fixing decorative lamination conforming to IS: 2046 : 1995 as per approved make, brand, finish and thickness with fitting, fixing the same on Particle/MDF / Ply Boards with recommended / approved adhesive with proper clipping the sides for better attachment as per direction of Engineer-in-charge.The rate includes the cost of abour, adhesive and all incidental charges thereof. In ground floor 121 Supplying fitting, fixing decorative lamination conforming to IS: 2046 : 1995 as per approved make, brand, finish and thickness with fitting, fixing the same on Particle/MDF / Ply Boards with recommended / approved adhesive with proper clipping the sides for better attachment as per direction of Engineer-in-charge.The rate includes the cost of labour, adhesive and all incidental charges thereof.In ground floor Glossy/Matt/Suede excluding surface texture or metallic lustre. (i) Thickness of laminate 1.5mm

Please Enable Macros to View BoQ information