Ram Ganga awasiye Yojna ke sec-11 me box village ka nirman karye (Exhibition Hall, Club House, kiosk/Outlet, Swimming pool and development works (Road, Boundary wall, Water Body, Screen wall, Toilet Block, Guard room, Main gate, horticulture, externa

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil 0.00 LVL. TO 1.50 MTR. (D.S.R.-2.8.1)

1.50 LVL. TO 3.00 MTR. (D.S.R.-2.8.1+2.26.1)

Filling available excavated earth (excluding rock) in trenches, plinth,sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. ((D.S.R.-2.25))

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. ((D.S.R.-2.25a))

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :, 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) ((D.S.R.-4.1.8))

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. ((D.S.R.-2.27))

With Chlorpyriphos/ Linadane E.C. 20% with 1% concentration. ((D.S.R.-2.35.3.1))

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. Concrete of M25 grade with minimum cement content of 330 kg /cum, All works above plinth level upto floor V level ((D.S.R.-5.33.2.1)) SLAB)

All works above plinth level upto floor V level ((D.S.R.-5.33.2.1)) (BEAM)

All works upto plinth level ((D.S.R.-5.33.1.1)) FOOTING

All works upto plinth level ((D.S.R.-5.33.1.1)) (COLUMN)

All works upto plinth level ((D.S.R.-5.33.1.1))

Add for using extra cement in the items of design mix over and above the specified cement content therein. (D.S.R.-5.35)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand) ((D.S.R.-6.1.2))

Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size). ((DSR-4.10))

Painting on D.P.C. with two coats of airblown bitumen 85/50 or 85/25 @ 1.7 kg/sqm approx. including cost of fuel if any. ((DSR-4.13))

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand), Ground Floor

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand), Ground Floor

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more., Ground Floor

15 mm cement plaster on rough side of single or half brick wall of mix:1:6 (1 cement: 6 coarse sand) ((DSR-13.5.2)), Ground Floor

12 mm cement plaster of mix :1:6 (1 cement: 6 coarse sand) ((DSR-13.4.2)), Ground Floor

15 mm cement plaster on rough side of single or half brick wall of mix : 1:4 (1 cement: 4 coarse sand). ((DSR-13.5.1))

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. ((DSR-5.30))

Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished) machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade. (FLOORING), Ground Floor ((DSR-8.2.2.2 ))

Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished) machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade. (skirting), Ground Floor ((DSR-8.2.2.2 ))

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth ((DSR-4.17))

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:, (a) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. Single leaf. ((DSR-9.21.1))

(b) Double leaf (((DSR-9.21.1+9.26))

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Three track three panels sliding window with two glazed & one wire mesh panels with alluminium channel for roller track, wool pile, nylon rollers with s.s. 304 body., Using R2 series with foame (70mm & above)x(40 mm & above) & both glazed and fly screen sash (25 mm & above)x(50mm & above with zinc alloy (zamak) powder coated touch lock with hook (Height up to 1.20 meter) (D.S.R.-9.147 A4.1)

Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer., Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately) (D.S.R. 10.15.2)

Painting with silicon & acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces :Two coats, Ground Floor

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)(Outer surface), Ground Floor

Distempering (Two coat) with oil bound distemper of approved brand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as Berger,J&N, Shalimar, Asian paints after thoroughly brushing the surface free from mortar droppings & other foreign matters & also including preparing the surface even with plaster of paris or approved synthetic material & sand papered smooth including cost ofall materials. (For ceiling surface), Ground Floor

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. , Ground Floor

Centering and shuttering including strutting, propping etc. and removal of form for :, Foundations, footings, bases of columns, etc. for mass concrete (D.S.R.-5.9.1)

Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick (D.S.R.-5.9.20)

Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick (D.S.R.-5.9.21)

Columns, Pillars, Piers, Abutments, Posts and Struts (D.S.R.-5.9.6)

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. ((D.S.R.-10.28))

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished seamless type tubes, Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished seamless type tubes (D.S.R.-10.16.2)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade.Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture : (M.S. works). ((D.S.R.-13.62.1))

Providing and fixing in position Colour Natural anodized heavy duty Aluminium Doors/windows/ Sections for outer frame, shutter frame, mullions, beads etc. including providing and fixing hardware items, 6mm clear float glass, approved EPDM gasket, wool pie, cleats and other accessories as required. Anodic coating shall be 0.025 mm as per Standard Code. The Aluminium frame will not be less than 2.75 mm thick. The rate shall include caulking around frames with polysulphide sealant, wherever required, SS friction hinges handles, locks, concealed tower bolts etc. as per approved makes and specifications. The contractor has to provide shop drawings before the commencement of work for the architect's approval. The contractor has to follow profiles of the sections shown in the Drawing or approved equivalent to the mentioned. Appropriate profiles of EPDM gaskets shall be inserted between aluminium frames/ beadings and glass; as well as both inside and outside around the periphery of the shutters, to make the windows air and water-tight. The fixing shall be done on aluminium rough ground openings at anchorage locations, in jambs, sills and heads by drilling holes with an electric drill, inserting Stainless Steel Counter sunk screws. The entire periphery shall be sealed by application of approved weather silicon sealant between the aluminium and masonry from both outside and inside to make the windows watertight. Each openable window shutter shall be provided 2 nos. of 255mm adjustable Stainless Steel Friction stay, button locking handle as per the design to be approved by the Architect. Door shutters with lock, handles, tower bolt, door stoppers, hinges as required, floor springs/Hydraulic door closer etc. complete. Rate inclusive of 6mm thick toughened glass/ 4mm thick ACP Sheet. The Contractor shall make provision for cutting of glass wherever required as per drawing and as required by the Architect. (Area of door and windows shall be measured for payment purpose). (NSR.)

Supply and fixing of approved Make Motorized Galvanized Steel Single Wall Rolling Shutter, vertical rolling type, used for internal and external applications. The rolling shutter components include Galvanized Steel Slats (as per IS 6248), MS Bottom Plate, MS Side Guides, MS Brackets, MS Shaft Assembly (all with one coat of standard primer), GI Hood Cover, and Hardware. The Imported Make Automation System consists of an Indirect Drive with a chain wheel mechanism, a Manual hand chain for emergency operation, an Inbuilt control, a 3-way push button, safety, and operating accessories. Slat Curtain: Galvanized Steel slats (1.0 mm thick for shutter width >3.5m and 0.9 mm thick for shutter width <3.5m) with continuous single piece without joints, 88 mm corrugated type profile. Bottom Plate: GI bottom plate 2.5 mm thick with angle stiffener, L-shaped bottom profile (120 mm height), optional rubber sealing. Side Guides: GI Box Type Guide, 100 x 85 x 2 mm thick. Bracket Plate: Mild Steel, minimum 3.0 mm thick, motor side bracket with chain-sprocket mechanism, other side with bearings. Roller Shaft: Mild Steel hollow tubular pipe, diameter 100-300 mm, machined shaft and flange, slat curtain fixed by nuts & bolts. Hood Cover: GI sheet, 0.8 mm thick, hexagonal shape. Automation System: Electric motor (Imported Make), 220 V / 380 V, 1 phase or 3 phase, emergency chain wheel drive, safety device, inbuilt thermostat. Control: Inbuilt Basic control card with integrated limit switch. Standard Accessories: Push Button, 3-way Push Button standard with automation system, motor cover (GI sheet, 0.8 mm thick), bottom rubber sealing, manual hand chain, including powder coat painting on both sides of shutter & wherever necessary as per approved color, etc., complete in all respects. (NSR.)

Providing and installation of customised vertical concrete panels with precise dimensions and robust material specifications. Each panel measures 120 mm in width, 1500 mm in height, and has a thickness of 22 mm having flutes/grooves/undulation or of approved size of desired finish and pattern including the cost of graphics illustrations as approved by Architect in charge. The composition of tiles should be ‘43’ Grade Portland cement and homogeny pigmentation should be done with exterior grade synthetic inorganic iron oxide pigments. e pigmentation should be homogeneous and in accordance with British Standards BS EN 12878:1999. The other additives should be fine washed graded quartz, super plasticisers and integrated water proofing agents and others. The tiles should be produced with high vibration technology and concrete mix design compressive strength equivalent to M-40 Grade@28 days. The top surface of the tiles should be sealed with in surface water absorption of tiles, less than 1% and water absorption by 24 hrs immersion method, less than 8%. The tiles should be applied on a rough plaster of 1:3 cement mortar 1:3 (1 cement: 3 coarse sand) and the fixing of tiles should be done by ‘Greyscale’ tile adhesive or equivalent as per manufacturer’s laying instruction. ln addition to this tiles will also have an inSert of L profile fixed using epoxy and screwed on the wallfor additional safety. The installation should be meticulously carried out under the guidance and approval of the appointed Architect or Engineer-in-Charge, ensuring that all work is executed to the highest standards of quality and precision. (NSR)

Design, fabricating, supply and installation of customised perforated MS sheet in extruded triangular or parametrically eveolved pattern as approved by drawing submitted to Architect in charge at all levels mild steel (MS) sheets, which includes a series of detailed processes to achieve the desired design and finish through CNC cutting, which allows for precise and intricate patterns to be cut into the MS sheet based on the approved drawings and designs provided by the Architect in charge. Following the cutting process, etching and engraving are performed to add depth and detail to the design, enhancing the ornamental appearance. These processes involve carefully removing material from the surface to create the desired patterns and textures. After the cutting, etching, and engraving are completed, refilling is conducted to ensure the engraved areas are smooth and consistent with the overall design. This step ensures that the intricate details are highlighted and any imperfections are corrected. The MS sheet used for this work will be of an approved thickness to ensure structural integrity and durability. Additionally, the specification includes the cost of powder coating the MS sheet in an approved shade. (NSR )

Providing and fixing roofing consist of 0.8 mm thick galvanized steel deck sheet confirming to IS 277:1992 used as permanent shuttering over which MS wire mesh 3 mm laid at 100x100 mm grid including edge trim covered with concrete. This metal deck will be supported on structural steel beam with shear studs. (Structural steel like Beam, column, joists etc. & concrete of different grade as per design will be paid separately). (NSR)

DOUBLE SKIN ROOF SHEETING Providing & fixing Top layer of profile sheet of 1015 mm effective cover width and nominal 28.5 mm deep ribs with subtle square fluting in the five pans at nominal 200 mm centre to-centre. The end rib shall be designed for anti-capillary action, to avoid any seepage of water through the lateral overlap. The feed material is manufactured out of nominal 0.50 mm Total Coated Thickness (TCT), Hi-Tensile steel with min. 550 mpa yield strength, metallic hot dip coated with Aluminum-Zinc alloy (55% Aluminum, 45% Zinc) as per AS 1397 - Zincalume AZ150 (Min. 150 gms/sq.mt total on both sides). Thereafter providing sub girt in 0.5 mm thickness in Z shape of 50 mm web and 20 mm flange over bottom skin sheet shall be Panel rib profile of LYSAGHT to be installed over purlins directly with self drilling & tapping screws. to make air gap of 50 mm for providing sandwich insulation of 50 mm thick rock wool pads having density of 48 kg/mtr cube with HDPE vapor liners on both top and bottom surface of Rock wool. Complete job with all hardware, accessories, material and labour. (NSR)

Design & Fabricating Ornamental work on mild steel (MS) sheets, which includes a series of detailed processes to achieve the desired design and finish through CNC cutting, which allows for precise and intricate patterns to be cut into the MS sheet based on the approved drawings and designs provided by the Architect in charge. Following the cutting process, etching and engraving are performed to add depth and detail to the design, enhancing the ornamental appearance. These processes involve carefully removing material from the surface to create the desired patterns and textures. After the cutting, etching, and engraving are completed, refilling is conducted to ensure the engraved areas are smooth and consistent with the overall design. This step ensures that the intricate details are highlighted and any imperfections are corrected. The MS sheet used for this work will be of an approved thickness to ensure structural integrity and durability. Additionally, the specification includes the cost of powder coating the MS sheet in an approved shade. (make Metaguise/Citadel/ Woodform Architectural or equivalent) (NSR)

Providing and fixing Structural Glazing consisting of fixed panels as per the elevation drawings enclosed, fabricated out of heavy-duty aluminium extruded profiles anodized (25 microns) as per approved shade. All aluminium members & profiles shall be of AC 25 grade as per specification. The Aluminium members shall be protected with Masking Tapes all around the profiles for safety against external scratches at the site. (Masking Tapes shall be removed only at the time of handing over as per the instructions of the Project Manager).Structural Glazing as above with 6mm thick touSupply of colour coated Nominal 0.45mm base metal thickness (0.50mm TCT) LYSAGHT CUSTOMORB sinusoidal profile of 990 mm effective cover width, with fourteen smooth sinusoidal corrugation, 19mm rib height spaced at 76mm c/c. The end rib shall have anti-capillary groove. The steel sheet is having high tensile sheet G550 (Fy=550Mpa), metallic coated with Zinc Aluminium alloy (i.e. 55% Al, 43.4% Zinc, 1.6% Si - Zincalume), AZ150 (min 150 gm/m2 total on both side), pre-painted with Super Durable Polyester Colorbond XRW quality paint includes inorganic infrared reflective pigment (High SRI-”Thermatech technology”) of 20μm exterior coat on top surface and 5μm reverse coat on back surface over 5μm primer coat on both surfaces of approved color shade by concern authority. The sheet conforms to general requirement of AS/NZS 2728 type 4 / IS 15965 class 3 durability and gloss value of 25% - 40% of Tata BlueScope Steel make. The sheet shall have brand marking of the manufacturer giving product details on the back of the sheet at every 1 meter c/c for confirming genuinity of the material. ghened Glass (Make - Asahi, Series- Ecosence Enhance / Solar control Glass) as per approved colour.All the accessories like flashing / capping shall be made from the material specifications (0.45MM BMT /0.5 MM TCT, COLORBOND® XRW) G 550 mentioned as above in approved colour shade & as per manufacturers’ recommendation Including Acp Sheet . ( NSR) (NSR)

Providing and fixing of colour coated Nominal 0.45mm base metal thickness (0.50mm TCT) LYSAGHT CUSTOMORB sinusoidal profile of 990 mm effective cover width, with fourteen smooth sinusoidal corrugation, 19mm rib height spaced at 76mm c/c. The end rib shall have anti-capillary groove. The steel sheet is having high tensile sheet G550 (Fy=550Mpa), metallic coated with Zinc Aluminium alloy (i.e. 55% Al, 43.4% Zinc, 1.6% Si - Zincalume), AZ150 (min 150 gm/m2 total on both side), pre-painted with Super Durable Polyester Colorbond XRW quality paint includes inorganic infrared reflective pigment (High SRI-”Thermatech technology”) of 20μm exterior coat on top surface and 5μm reverse coat on back surface over 5μm primer coat on both surfaces of approve d color shade by concern authority. The sheet conforms to general requirement of AS/NZS 2728 type 4 / IS 15965 class 3 durability and gloss value of 25% - 40% of Tata BlueScope Steel make. The sheet shall have brand marking of the manufacturer giving product details on the back of the sheet at every 1 meter c/c for confirming genuinity of the material. All the accessories like flashing / capping shall be made from the material specifications (0.45MM BMT /0.5 MM TCT, COLORBOND® XRW) G 550 mentioned as above in approved colour shade & as per manufacturers’ recommendation.0 to 305mm Girth (NSR)

306 to 610mm Girth (NSR)

Providing and fixing heavy-duty hardware fittings manufactured from Stainless Steel Grade 304, finished with a bright polished brass or lacquered PVD (Physical Vapor Deposition) finish as specified, to be installed on door shutters of required thickness. The work includes 150 mm heavy-duty Decorative Door Stoppers provided with a high-quality, durable vulcanized rubber cushion to prevent impact damage, along with door bolts, tower bolts, and handles of required sizes. The work includes 150 mm heavy-duty door stoppers provided with a high-quality, durable vulcanized rubber cushion to prevent impact damage, along with door bolts, tower bolts, and handles of required sizes (NSR-1)

Providing and fixing heavy-duty door handles manufactured from Stainless Steel Grade 304, finished with a high-gloss bright polished brass lacquered PVD finish as per approved shade and design. The handles shall be of the required size 125 mm and fixed to door shutters of varying thicknesses as per the direction of the Architect/Engineer-in-Charge. with material test certificate. (ODG-11-10x125) (NSR)

Providing & fixing EN:1154 Certified 500000 cycle tested door closer made of Aluminium Diecasted body having UL stamping sutable for 80kg with double speed adjustment with necessary accessories and screws etc. Complete. (NSK-680) (NSR)

Providing and fixing powder-coated aluminium work for partitions, made of standard hollow sections (Hindalco or equivalent) as per the approved drawings and design. The framework shall consist of 45x45 mm sections with a wall thickness of 1.5 mm (16 gauge), manufactured from Aluminium Alloy 6063-T6. The sections shall be powder-coated with a minimum thickness of 50 microns in the specified color. The structure is to be fixed with expansion hold-fasts, rawl plugs, and high-quality stainless steel screws. The partition shall be glazed with 5 mm thick clear float glass (of approved make like Saint-Gobain/ModiGuard), secured using EPDM rubber gaskets and glazing clips to ensure a rattle-free and airtight finish. The work includes all necessary hardware, including cleats, joints, and sealants to make the partition perfectly rigid and aligned. All joints shall be miter-cut at 45° or butt-jointed as per the direction of the Engineer-in-Charge. The rate includes the cost of all materials, labor, scaffolding, and cleaning of glass/sections upon completion. (NSR.)

Design development, coordination, and preparation of detailed shop drawings and fabrication drawings for all prefabricated components, strictly based on architectural drawings and design inputs received from the Architect-In-Charge, including structural framing, façade systems, cladding, decks, staircases, shutters, signage, and allied elements; comprising study of drawings, design coordination, preparation of execution-ready and CNC-compatible fabrication drawings with complete detailing of members, connections, fixings, materials, finishes, tolerances, and installation methodology; including all revisions, modifications, coordination meetings, and final approvals, prepared in compliance with applicable Indian Codes and Standards, complete in all respects as directed by the Engineer-in-Charge. (NSR)

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.Internal work - Exposed on wall 15 mm nominal outer dia pipes (DSR -18.10.1)

20 mm nominal outer dia pipes (DSR -18.10.2)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge., Internal work - Exposed on wall20 mm nominal outer dia Pipes (DSR -18.7.2)

25 mm nominal outer dia Pipes (DSR -18.7.3)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc., 15 mm nominal outer dia pipes (DSR -18.8.1)

20 mm nominal outer dia pipes (DSR -18.8.2)

Providing and fixing G.I. pipes complete with GI fittings and clamps including cutting and making good the walls etc. External work, 40 mm dia, nominal bore (DSR -18.12.5)

50 mm dia, nominal bore (DSR -18.12.6)

Providing and fixing of gun metal gate valve with CI wheel of approved quality (screwed ends), 25mm dia, nominal bore (DSR -18.17.1)

32 mm dia, nominal bore (DSR -18.17.2)

40 mm dia, nominal bore (DSR -18.17.3)

50 mm dia, nominal bore (DSR -18.17.4)

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :, 25 to 40 mm nominal bore (DSR -18.13.1)

50 to 80 mm nominal bore (DSR -18.13.2)

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length, 15 mm nominal bore (DSR -18.21.2.1)

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet 100 mm diameter (DSR -18.22.1)

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work (internal work -exposed on , walls)15 mm nominal outer dia pipes (DSR -18.38.1)

20 mm nominal outer dia pipes (DSR -18.38.2)

Painting GI pipes and fittings with two coats of anti corrosive bitumastic paint of approved quality, 40 mm dia, nominal bore (DSR -18.40.5)

50 mm dia, nominal bore (DSR -18.40.6)

Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work, 40 mm dia, nominal bore (DSR -18.41.5)

50 mm dia, nominal bore (DSR -18.41.6)

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :, 20 mm nominal bore (DSR -18.18.2)

25 mm nominal bore (DSR -18.18.3)

Providing and fixing G.I. union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (new work), 15mm nominal bore (DSR -18.46.1)

20mm nominal bore (DSR -18.46.2)

25mm nominal bore (DSR -18.46.3)

32mm nominal bore (DSR -18.46.4)

Providing and fixing C.P. brass bib cock of approved quality confirming to IS:8931, 15mm nominal bore (DSR -18.49.1)

Providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology., 15mm nominal bore (DSR -18.84.1 )

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 a) 15 mm nominal bore., 15 mm nominal bore (DSR -18.53.1)

Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, depth upto 1.5 m including getting out the excavated materials, returning the soil as required in layers not exceeding 20 cm in depth including consolidating each deposited layers by ramming, watering etc. stacking serviceable material for measurements and disposal of unserviceable material as directed, within a lead of 50m :, Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia. (DSR -2.10.1.2)

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :, 100 mm O.D. (DSR -19.6.1)

150 mm O.D. (DSR -19.6.2)

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : , 110/100 mm diaRmt pipe (DSR -19.2.1)

160/150 mm diaRmt pipe (DSR -19.2.2)

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 180x150 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (DSR -19.4.3.1)

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) Fisnihed with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (DSR -19.7.1.1)

(b) Inside size 1200 x 1200mm and 1.0meter deep including C.I. Cover frame. (DSR -19.7.2.1)

Extra over Item No. 24.27 for every additional depth of 0.10 metre or part there of main hole(a) Size 900 x 800 mm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (DSR -19.8.1.1)

(b) Size 1200 x 900mm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (DSR -19.8.2.1)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc., For Internal Toilet , 15 mm nominal outer dia Pipes (DSR -18.8.1)

20 mm nominal outer dia Pipes (DSR -18.8.2)

25 mm nominal outer dia Pipes (DSR -18.8.3)

32 mm nominal outer dia Pipes (DSR -18.8.4)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (DSR -18.7), Internal work - Exposed on wall , 20 mm nominal bore (DSR -18.7.2)

25 mm nominal bore (DSR -18.7.3)

32 mm nominal bore (DSR -18.7.4)

40 mm nominal bore (DSR -18.7.5)

Providing and fixing GI pipes complete with GI fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on Wall, Terrace loop & Tank Filling Pipe, 20 mm nominal bore (DSR -18.10.2)

25 mm nominal bore (DSR -18.10.3)

32 mm nominal bore (DSR -18.10.4)

40 mm nominal bore (DSR -18.10.5)

50 mm nominal bore (DSR -18.10.6)

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality , 20mm diaRmt pipe (DSR -18.40.2)

25mm diaRmt pipe (DSR -18.40.3)

32mm diaRmt pipe (DSR -18.40.4)

40mm diaRmt pipe (DSR -18.40.5)

50mm diaRmt pipe (DSR -18.40.6)

65mm diaRmt pipe (DSR -18.40.7)

80mm diaRmt pipe (DSR -18.40.8)

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) , 20mm diameter pipe (DSR -18.46.2)

25mm diameter pipe (DSR -18.46.3)

32mm diameter pipe (DSR -18.46.4)

40mm diameter pipe (DSR -18.46.5)

50mm diameter pipe (DSR -18.46.6)

65mm diameter pipe (DSR -18.46.7)

80mm diameter pipe (DSR -18.46.8)

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : For vertical pipe connection with terrace ringmain, 20 mm nominal bore (DSR -18.17.1A)

25mm nominal bore (DSR -18.17.1)

32mm nominal bore (DSR -18.17.2)

40mm nominal bore (DSR -18.17.3)

50mm nominal bore (DSR -18.17.4)

65mm nominal bore (DSR -18.17.5)

80mm nominal bore (DSR -18.17.6)

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete , 25 to 40 mm nominal bore (DSR -18.13.1)

50 to 80 mm nominal bore (DSR -18.13.2)

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./H.P.H.D. plastic ball. , 15 mm nominal bore, 105 mm long, weighing not less than 138 gms (DSR -18.62.1)

20 mm nominal bore, 120 mm long, weighing not less than 198 gms (DSR -18.62.2)

25 mm nominal bore, 152 mm long, weighing not less than 440 gms (DSR -18.62.3)

40 mm nominal bore, 206 mm long, weighing not less than 690 gms (DSR -18.62.4)

50 mm nominal bore, 242 mm long, weighing not less than 1240 gms (DSR -18.62.5)

Providing and fixing MS pipe puddle flanges of required size with 600mm long with 6mm thick MS plate of size 300mm x 300mm of suitable size properly fixed in RCC walls of water tanks, including necessary welding complete in all respect as per details shown on darwings and directions of Engineeer-in-charge for water tanks., 25mm dia. (NSR)

40mm dia. (NSR)

50mm dia. (NSR)

80mm dia. (NSR)

100mm dia. (NSR)

150mm dia. (NSR)

200mm dia. (NSR)

250mm dia. (NSR)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS :13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes., 110 mm dia (for rain water) (DSR -12.41.2)

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion., Single Push Fit Coupler, 110 mm dia (DSR -12.42.2.2)

Single tee with door, 110x110x110 mm (DSR -12.42.3.2)

Plain bend 87.5 deg , 110 mm dia (DSR -12.42.5.2)

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete, 110 mm dia (DSR -12.43.2)

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. (DSR -12.22)

Providing and fixing 15 cm wide, 45 cm overall semi-circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete, 0.80 mm thick with zinc coating not less than 275 gm/m² (DSR -12.7.1)

Excavating trenches by mechinical / manual means of required width for pipes cables etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth including getting out the excavated soil , and then returning the soil as required , in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed , within a lead of 50 m. All kind of soil , Pipes, cables etc. exceeding 80 mm dia . But not exceeding 300mm dia. (DSR -2.10.1.2)

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design: , 100mm dia SW pipe (DSR -19.2.1)

Providing, fixing, jointing and testing, uPVC SWR pipes, - type B conforming to IS : 13592 to wall, ceiling and floor, approved quality, complete, for soil, waste & rain water drain including pushfit jointing with seal ring. (i) Single socketed pipes. (NSR), Internal Toilet (Soil & Waste Pipe), 75 mm (NSR)

110 mm (NSR)

Exposed on Wall (Soil & Waste Pipe), 110 mm (NSR)

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. (NSR), Bend without door (45°) (NSR), 75mm

Bend without door (87.5°) (NSR), 75mm bend

Y' Fitting without door (NSR), 75mm

Single Tee without door (NSR), 75mm

Single Tee with door (NSR), 75mm

Bend with door (87.5°) (NSR), 75mm

Reduced 'Y' Fitting without door (NSR), 110mm x 75mm

Reduced Tee with door (NSR), 110mm x 75mm

Coupler (NSR), 75mm

Vent Cowl (NSR), 110mm

Providing, fixing, jointing and testing, unplasticized PVC pipes - 10 kg/cm2 confirming to IS : 4985 to wall, ceiling and floor, approved quality, complete, for waste water drain including jointing with rubbering/solvent/solution and airtight joints, etc. For Wash basin & Urinal (NSR), 32mm dia. Pipe (NSR)

50mm dia. pipe (NSR)

Elbow (45°) (NSR), 32mm

Elbow (90°) (NSR), 32mm

T fitting (NSR), 32mm

Coupler (NSR), 32mm

Providing, fixing, jointing and testing , of PVC Multi Floor Trap without jali of minimum 50 mm water seal, making necessary cutting in slab or floors and making good including supports with cement concrete 1:3:6 complete as approved by Engineer-in-Charge., 110mm x 75mm x 50mm/40mm (Toilet) NSR

Providing, fixing, jointing and testing , of PVC Nahani Trap without jali of minimum 50 mm water seal, making necessary cutting in slab or floors and making good including supports with cement concrete 1:3:6 complete as approved by Engineer-in-Charge, 110mm x 75mm (Toilet & Kitchen) (NSR)

Providing and fixing PTMT grating of approved quality and colour, Rectangular type with openable circular lid., 150 mm nominal size square 100 mm diameter of the inner hinged round grating (including balcony) (DSR -18.58.2.1)

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design 150 x 100mm size P-type , With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (DSR -19.4.2.1)

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete:, 100 mm diaRmt (DSR -19.1.1)

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:, White Vitreous china Orissa pattern W.C. pan of size 600x500 mm with integral type foot rests (NSR)

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :, W.C. pan with ISI marked white solid plastic seat and lid (DSR -17.2.1)

Providing and fixing of wall mounting type water closet of approved quality & make and as per the direction of Engineer-in-charge. (NSR)

Providing and fixing of S.STEEL TOILET PAPER HOLDER (WITH FLAP) of approved quality & make and as per the direction of Engineer-in-charge. (NSR)

Providing and fixing of SANITARY BIN WITH PEDAL, 18 LITERS, BLACK of approved quality & make and as per the direction of Engineer-in-charge. (NSR)

Providing and fixing of SWING HANDICAP GRAB BAR - S.STEEL, 32MM DIA. of approved quality & make and as per the direction of Engineer-in-charge. (for H. Toilet) (NSR)

Providing and fixing of S.STEEL GRAB RAIL, 300MM,32MM DIA of approved quality & make and as per the direction of Engineer-in-charge. (for H. Toilet) (NSR)

Providing and fixing Hand Shower (Health Faucet) with 8mm Dia,1.2 Meter Long Flexible Tube & Wall Hook of approved quality and make as approved by Engineer - in - charge. (NSR)

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. (DSR -17.16A)

Providing and fixing of Under Counter Basin of approved quality & make and as per the direction of Engineer-in-charge. (NSR)

Providing and fixing of AUTOMATIC TAP, BASIN MOUNT of approved quality & make and as per the direction of Engineer-in-charge. (NSR)

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- , (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing of AUTO SOAP DISPENSER of approved quality & make and as per the direction of Engineer-in-charge. (NSR)

Providing and fixing of S.STEEL HAND DRYER (HEAVY TRAFFIC ) of approved quality & make and as per the direction of Engineer-in-charge. (NSR)

Providing and fixing of AUTOMATIC HRT TISSUE PAPER ROLL DISPENSER of approved quality & make and as per the direction of Engineer-in-charge. (NSR)

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. (DSR -17.72)

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. (DSR -17.31)

Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever require, Kitchen sink with drain board, 510x1040 mm bowl depth 200 mm (DSR -17.10.1.3)

Providing and fixing of URINAL WITH SENSOR (BATTERY + ELECTRICAL) of approved quality & make and as per the direction of Engineer-in-charge. (NSR)

Providing and fixing of Kent Elite Plus Water Purifier, cooler complete (RO+UV+UF+TDS Control) with flow rate (50L/hr) including all its accessories, complete in all respect including testing etc. (NSR)

(a) Supplying, installation, testing and commissioning of electric driven terrace pump conforming to IS 12469: 2019 suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (b) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal as required. (c)Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class 'F' insulation, conforming to IS-12615: 2018. (d) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. (e) Suitable cement concrete foundation duly plastered and with anti vibration pads., 450 lpm at 35 m Head (DSR -18.4.2)

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required. (for terrace booster pump) (DSR -18.22)

Providing & fixing of start/stop push buttons including complete connection etc. as required. (for terrace booster pump) (NSR)

Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required (for terrace booster pump) (DSR-16.8)

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required, 150 mm dia. (DSR -18.11.6)

100 mm dia. (DSR -18.11.5)

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required, 150 mm dia. (DSR -18.14.7)

100 mm dia. (DSR -18.14.5)

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : (80 mm nominal bore (DSR -18.7.6)

100 mm nominal bore (DSR -18.7.7)

150 mm nominal bore (DSR -18.7.8)

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required Single headed Gunmetal (DSR -18.9.1)

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585, 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket., 40 m (DSR -18.17.2)

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required , Gun metal (DSR -18.16.1)

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required , Gun metal (DSR -18.18.1)

Providing and fixing standard fire mans axe with heavy duty insulated rubber handle. (NSR)

Providing of FHC Door made of 16 gauge MS Sheet with frame of size 105x70mm complete door and frame assembly including all hardwares (Concealed Flush handle,Allen Key Lock, MS Hinges, 5mm Thick Float glass) & accesories . The door to be painted with fire resistance paint. The scope shall also include the painting of the frame with the same paint as the shutter or complete as per direction of Engineer-in-charge. (Approx. size of door: 900mm Wide & 1500mm Height) (NSR)

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required. (DSR -18.13)

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required. (DSR -18.2)

Supply and fixing of C02 type fire extinguisher 4.5 kg. capacity (ISI Marked IS : 2878 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. (NSR)

Supply and fixing of fire extinguisher, ABC Type 6.00 kg. capacity (ISI Marked IS : 15683 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. (NSR)

Providing and fixing Fire related signages printed on photoluminescent U1000 aluminium sheet of 1.0 mm (+-10%) containing Lumigen II as base chemical, covered under UV stablized coating and of appropriate size including fixing on wall, door, ceiling etc. with proper clamps, hangers, cleats, anchor fasteners etc. complete in all respects as directed by Engineer-in-charge. (NSR)

Supplying, installation, testing & commissioning of central graphical fire alarm management system to centrally monitor and operate the fire alarm system complete as required. (DSR -17.2.2)

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required. (DSR -17.2.4)

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required. (DSR -17.2.5)

Supplying, installation, testing & commissioning of addressable manual call point complete as required. (DSR -17.2.14)

Supplying, installation, testing & commisssioning of intelligent addressable programmable sounder complete as required. (DSR -17.2.6)

Supplying, installation, testing & commissioning of fault isolator complete with base as required. (DSR -17.2.7)

Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required. (DSR -17.2.17)

Supplying, installation, testing & commissioning of fire fighter phone jack complete as required. (DSR -17.2.19)

Supplying, installation, testing & commissioning of addressable fire control module complete as required. (DSR -17.2.10)

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required. (DSR -17.2.9)

Supplying, installation, testing & commissioning of addressable beam detector with short circuit isolator (inbuilt or seperate) complete with emitter and receiver including connections with remote test features etc complete as required. (DSR -17.2.12)

Supplying, installation, testing & commissioning of intelligent interface unit BACnet/ Modbus protocol i.e. supplying communication links between building management system and fire alarm control panel complete as required. (DSR -17.2.18)

Supplying, Installation, Testing & Commissioning of Modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling/heating having 100% hermetically sealed inverter type twin Rotary/Scroll Compressor(s),minimum two compressors (with individual separate PCB) for above 14HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R-410-A Refrigerant or equivalent, vibration Isolators with suitable foundation etc. complete as required. To have better efficiency condenser fan shall be capable to operate at different speed with respect to load.The unit shall deliver the rated capacity and in confirmation as per IS 18728:2024 and CPWD Specifications and work even at 50°C ambient temperature without tripping. The system shall be able to deliver 100% of the rated capacity upto 39 °C. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply and BMS compatible. The unit shall be filled with first charge of the refrigerant and ready for use as required. The condenser should be coated with a hydrophilic film to prevent water accumulation on the surface of the heat exchanger, enhance water dispersion, and reduce the risk of degradation, thereby improving overall performance and durability. The Indian Seasonal Energy Efficiency Ratio (ISEER) of the unit shall be as per Energy Conservation and Sustainable Building Code (ECSBC) 2024 as below and complete as per CPWD specification, connections, inter connections etc. as required. (For capacity <40 kWr ISEER 7.4, Capacity > 40 and <70 ISEER 7.5, Capacity > 70 ISEER 7.6 for Super ECSBC Building) For Cooling or Heating or Both, 6 HP to 8 HP (DSR -31.3.1)

10 HP to 12 HP (DSR -31.3.2)

14 HP to 22 HP (DSR -31.3.3)

Supplying, Installation, Testing and Commissioning of following minimum capacity Double way VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration Isolation, Corded remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Singnals. The cooling capacity of indoor unit will be at air inlet conditions of 27 0C DB and 19 0C WB temperature. (Make will be same as of Outdoor) , 2.0 TR (DSR -31.7.3)

Supplying, Installation, Testing and Commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted high ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration Isolators, drain pan, drain pump, other necessary supports etc., suitable for operation on single phase AC supply 230 V ± 10%, 50 Hz complete as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Singnals. The cooling capacity of indoor unit will be at air inlet conditions of 27 0C DB and 19 0C WB temperature. (Make will be same as of Outdoor) , 5.5 TR (DSR -31.12.2)

6.6 TR (DSR -31.12.3)

8.0 TR (DSR -31.12.4)

Supplying, Installation, Testing and Commissioning of Y/T/Multi Joints. Joints shall be of same Original Equipment Manufacturer (OEM) make as of ODUs and IDUs (DSR -31.13), Indoor Units (DSR -31.13.1)

Outdoor Multi Joint (DSR -31.13.2)

Supplying, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of 19 mm thick insulation as given below for Suction and Liquid lines, all accessories as per specifications etc. as required , 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm (DSR -31.14.1)

9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm (DSR -31.14.2)

12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm (DSR -31.14.3)

25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm (DSR -31.14.7)

28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm (DSR -31.14.8)

41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm (DSR -31.14.12)

Providing and fixing rigid PVC piping complete with fittings, supports as per HITACHI STD.& specifications and duly insulated with 6 mm thick closed cell nitrile rubber insulation. Make:- Finolex,Supreme, Kissan ,Astral, or Hitachi/L G Approved Only, 32 mm dia (NSR)

25 mm dia (NSR)

Outdoor unit stand (NSR)

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required., 2 Pair (DSR - 1.18.2)

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. , 1 run of cable (DSR -1.53.1)

Providing and fixing HT danger notice plate 250 mm x 200 mm made of mild steel at least 2mm thick & vitreous enamelled white on both sides and with inscription in signal red colour on front side as required. (DSR -2.22)

Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :, With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 (DSR -18.34.1)

Supply and fixing of Single light Wall Bracket on matching M.D.F.E.G. Board base etc.Complete in all respect. CAT. - AAA (NSR )

Cost of Architectural Interior Lighting as per drawing and make approved approved by Architect in charge (NSR )

P& F Full Ht' Hanging Display of MS pipe of 10mm with the finish of Physical Vapour Decomposed Coating with bending and welding design as per drawing and approval of architect in charge. (C-11) (NSR )

P&F for Rooms Interior as per drawing received from Architect in charge, inluding furniture, HVAC, curtains, rugs, key management system etc. (NSR )

Providing and fixing in position at required location, GRC (Glass reinforced concrete) bush box Planter of height 1.5m, 1.50m length,width 500mm as per Architect's Design and as directed by project architect with all leads and lifts etc. complete in toto. (NSR )

Supply and installation of CARA Bench, measuring L74 x W35 x H42 cm, is constructed from a unique polymer blend that mimics the appearance of stone while offering lightweight durability. This material is 100% recyclable and features UV stabilization to prevent color fading, making it ideal for both indoor and outdoor applications. The bench combines aesthetic appeal with practical functionality, ensuring long-lasting performance and environmental sustainability. (NSR )

Supply, Installation and Commissioning of Kitchen setup, architectrual lighting and furninture customisation in desired material, shade and finish including burners, SS baskets, SS Cabinets etc. complete as per drawing and design approved and recived from Architect in charge ( Complete In all respect). (NSR )

Supply, Installation and Commissioning of architecterual lighting customised in desired material, shade and finish including track, cove, breacket, wall light etc. complete as per drawing and design approved and received from Architect in charge including the cost of shop drawing prepration and sampling ( Complete In all respect). (NSR )

Supply and installation of OVALE Lamp features a translucent white LED and stands 2 meters tall. It is constructed from a unique polymer blend with a black matte metal base, ensuring both durability and a modern aesthetic. The lamp includes a remote control for convenient operation and offers both warm white and cool white lighting options. Suitable for both indoor and outdoor use, it is designed as a floor lamp with a heavy base for stability.( Complete In all respect). (NSR )

Furniture as approved by Architect in charge.( Complete In all respect).

SITC of Twin Room Cottage, designed as a hybrid using Light Gauge Steel Framing (LGSF) techNoslogy, imported from Australia, incorporating mild steel load-bearing sections fabricated using CNC machines. The structure is engineered to withstand wind speeds of up to 180 kmph and is suitable for seismic zone IV. The RCC plinth is to be constructed as per the structural drawings, over which the prefabricated steel superstructure will be installed. The cost is inclusive of strcutural design for the substracture base on the recieved site inputs from Archiect and Structural incharge as per the basis of Indian codes and std. The construction fo the RCC upto plinth is inclusive along with the peripheral deck of min 1.2M wide with bamboowood decking. The external walls of the cottage are clad with thermo pine wood planks, providing both aesthetic warmth and weather resistance. These claddings are pre-treated and coated with weatherproof oils to ensure longevity and are fixed over OSB (Oriented Strand Board) sheets of 10 mm thickness. The structure is further wrapped with waterproof and termite-resistant OSB panels from both inside and outside for additional protection.The roof is constructed using asphalt shingles manufactured by TechNosNICOL Corporation, supported over a lightweight framing system. These shingles offer a 50-year warranty and provide excellent resistance against heat and water ingress. All internal walls and ceilings are finished with gypsum board over OSB panels and painted in the client’s choice of colour. Bathroom walls are tiled with ceramic tiles from Kajaria, and the toilets are fitted with high-quality sanitaryware from Kohler and Jaguar, including WC, washbasins, faucets, and other essential fixtures. All internal plumbing lines are made of CPVC/UPVC. The flooring in rooms is finished with indoor-grade wooden laminate flooring from Greenply, offering multiple colour options. ( Complete In all respect). "Toilets are laid with vitrified tiles, and the external deck area is made of thermo pine wood finished with weather-protective coatings. Doors are made of laminated flush doors, and windows/sliding doors are of UPVC sections fitted with 5 mm toughened glass. Options for double glazing units and mosquito mesh are available at extra cost. Skylights can also be provided in the roof structure if required. Electrical fittings include internal wiring with R R Kabel and fittings like switches/sockets of Legrand make and LED lights of Jaquar/Philips. Provisions for air-conditioning pipelines are embedded within wall layouts. " Decks are finished with 90×90 mm thermo pine balusters and 10 mm thick toughened glass inserts, with handrails made of 140×26 mm thermo pine sections, providing a secure yet transparent enclosure for the front deck areas. The structure includes two identical rooms of 10'-9" × 13'-6", each with an attached toilet (10'-9" × 5'-0") and a front-facing 11'-0" × 6'-0" deck space. The total covered area of the cottage is 592 square feet. All structural and finishing works shall be executed in compliance with the direction of the Engineer-in-Charge, adhering to the approved architectural and technical drawings. The cost of substructure is inclusive. The cost is inclusive of preparation of shop drawing and sample approval as per Architect in charge. The above mentioned finishes, makes of all items are subject to final approval by sample procurement and submission from any leading vendor to the Architect in charge. Cost of G+1 Prefab Cottages in group of 4

SITC of G+1 Prefabricated Twin Room Cottages, designed as a hybrid prefabricated structure using Light Gauge Steel Framing (LGSF) techNoslogy, with primary structural sections imported from Australia and secondary mild steel load-bearing members precision-fabricated using CNC machines. The complete superstructure is engineered to withstand basic wind speeds up to 180 kmph and is suitable for Seismic Zone IV, fully complying with relevant Indian Codes and Standards. The RCC substructure up to plinth level, including foundations, plinth beams, and pedestals, shall be constructed as per approved structural drawings. Over this, the prefabricated steel superstructure (G+1) shall be installed. The cost is inclusive of structural design for the superstructure and substructure, based on site inputs received from the Architect and Structural In-Charge. Construction of RCC up to plinth level is included, along with a peripheral deck of minimum 1.2 m width at the ground floor level, finished with thermo pine / bamboo wood decking with weather-protective coatings.Superstructure & Envelope The external walls of the cottages are clad with thermo pine wood planks, providing aesthetic warmth, durability, and resistance to harsh weather conditions. The timber cladding is factory-treated and coated with high-performance exterior oils and is fixed over 10 mm thick OSB (Oriented Strand Board) sheathing. The entire structure is further wrapped with waterproof and termite-resistant OSB panels, provided both internally and externally, ensuring enhanced durability and thermal performance. The roof system is constructed using asphalt shingles manufactured by TechNosNICOL Corporation, installed over a lightweight steel framing system. These shingles carry a 50-year manufacturer warranty and provide excellent resistance against heat, rain, and water ingress. Provision for skylights within the roof structure can be incorporated if required, at an additional cost.The structure is further wrapped with waterproof and termite-resistant OSB panels from both inside and outside for additional protection.The roof is constructed using asphalt shingles manufactured by TechNosNICOL Corporation, supported over a lightweight framing system. These shingles offer a 50-year warranty and provide excellent resistance against heat and water ingress. All internal walls and ceilings are finished with gypsum board over OSB panels and painted in the client’s choice of colour. Bathroom walls are tiled with ceramic tiles from Kajaria, and the toilets are fitted with high-quality sanitaryware from Kohler and Jaguar, including WC, washbasins, faucets, and other essential fixtures. All internal plumbing lines are made of CPVC/UPVC. The flooring in rooms is finished with indoor-grade wooden laminate flooring from Greenply, offering multiple colour options. ( Complete In all respect). "First Floor Construction & Deck The first floor is constructed using a prefabricated lightweight floor framing system, designed for residential live loads as per Indian Standards. The floor assembly includes structural steel joists, OSB sheathing, acoustic insulation, and finished flooring. A front-facing deck slab at first-floor level is provided for each cottage unit, supported on the LGSF/MS structure and designed for outdoor usage. The deck flooring is finished with thermo pine wood planks treated with weather-resistant coatings. Deck safety railings comprise 90 × 90 mm thermo pine balusters, 10 mm thick toughened glass panels, and handrails of 140 × 26 mm thermo pine sections, ensuring safety while maintaining visual transparency. Staircase Access to the first floor is provided through a custom-designed external metal staircase, fabricated from hot-dip galvanized mild steel sections. The staircase includes anti-slip treads, landings, and safety railings, finished with corrosion-resistant paint systems suitable for outdoor conditions. The staircase design is fully integrated with the architectural intent and structural system." "Toilets are laid with vitrified tiles, and the external deck area is made of thermo pine wood finished with weather-protective coatings. Doors are made of laminated flush doors, and windows/sliding doors are of UPVC sections fitted with 5 mm toughened glass. Options for double glazing units and mosquito mesh are available at extra cost. Skylights can also be provided in the roof structure if required. Electrical fittings include internal wiring with R R Kabel and fittings like switches/sockets of Legrand make and LED lights of Jaquar/Philips. Provisions for air-conditioning pipelines are embedded within wall layouts. INlducing electifcal fitures too " Decks are finished with 90×90 mm thermo pine balusters and 10 mm thick toughened glass inserts, with handrails made of 140×26 mm thermo pine sections, providing a secure yet transparent enclosure for the front deck areas. The structure includes two identical rooms of 10'-9" × 13'-6", each with an attached toilet (10'-9" × 5'-0") and a front-facing 11'-0" × 6'-0" deck space. The total covered area of the cottage is 592 square feet. All structural and finishing works shall be executed in compliance with the direction of the Engineer-in-Charge, adhering to the approved architectural and technical drawings. The cost of substructure is inclusive The cost is inclusive of preparation of shop drawing and sample approval as per Architect in charge. The above mentioned finishes, makes of all items are subject to final approval by sample procurement and submission from any leading vendor to the Architect in charge. Cost of Prefab admin, Cafeteria having backhouse facilites and a swimming pool at top

SITC of G+1 Prefabricated Twin Room Cottages, designed as a hybrid prefabricated structure using Light Gauge Steel Framing (LGSF) techNoslogy, with primary structural sections imported from Australia and secondary mild steel load-bearing members precision-fabricated SITC of Prefabricated Admin and Cafeteria Building, designed as a hybrid structure using Light Gauge Steel Framing (LGSF) techNoslogy, imported from Australia, incorporating mild steel load-bearing sections fabricated using CNC machines. The structure is engineered to withstand wind speeds of up to 180 kmph and is suitable for Seismic Zone IV. The RCC substructure up to plinth level, including foundations, pedestals, and plinth beams, shall be constructed as per approved structural drawings, over which the prefabricated steel superstructure shall be installed. The cost is inclusive of structural design for the substructure, based on site inputs received from the Architect and Structural In-Charge, designed as per Indian Codes and Standards. Construction of RCC up to plinth level is inclusive. Superstructure, Walls & Cladding The external walls of the building are clad with thermo pine wood planks, providing aesthetic warmth and weather resistance. The claddings are pre-treated and coated with weatherproof oils and are fixed over 10 mm thick OSB (Oriented Strand Board) sheets. The structure is further wrapped with waterproof and termite-resistant OSB panels from both inside and outside for additional protection and durability. Internal partitions are formed using the same LGSF system, sheathed with OSB boards and finished with gypsum boards. The roof system is constructed using asphalt shingles manufactured by TechNosNICOL Corporation, installed over a lightweight steel framing system. These shingles carry a 50-year manufacturer warranty and provide excellent resistance against heat, rain, and water ingress. Provision for skylights within the roof structure can be incorporated if required, at an additional cost.The structure is further wrapped with waterproof and termite-resistant OSB panels from both inside and outside for additional protection.The roof is constructed using asphalt shingles manufactured by TechNosNICOL Corporation, supported over a lightweight framing system. These shingles offer a 50-year warranty and provide excellent resistance against heat and water ingress. All internal walls and ceilings are finished with gypsum board over OSB panels and painted in the client’s choice of colour. Bathroom walls are tiled with ceramic tiles from Kajaria, and the toilets are fitted with high-quality sanitaryware from Kohler and Jaguar, including WC, washbasins, faucets, and other essential fixtures. All internal plumbing lines are made of CPVC/UPVC. The flooring in rooms is finished with indoor-grade wooden laminate flooring from Greenply, offering multiple colour options. ( Complete In all respect). "Roof & Rooftop Swimming Pool The roof structure is constructed using a lightweight framing system over LGSF members. The rooftop swimming pool is provided above the superstructure and shall be constructed as a structural RCC pool, designed for water load, live load, and safety as per relevant Indian Standards. The pool includes RCC base slab, side walls, waterproofing treatment, and finished pool surfaces. Adequate structural strengthening and load transfer systems are incorporated within the prefabricated structure to safely support the rooftop swimming pool. Pool edge coping, internal finishes, and waterproofing systems shall be executed as per approved drawings and specifications. Pool equipment, filtration systems, and accessories are excluded unless specifically mentioned. Internal Finishes – Admin & Cafeteria Areas All internal walls and ceilings are finished with gypsum boards over OSB panels and painted in the client’s choice of colour. Flooring in admin and cafeteria areas is finished with vitrified tiles, suitable for heavy footfall. Cafeteria Back-of-House Facilities The cafeteria includes dedicated back-of-house (BOH) areas comprising kitchen, food preparation zone, washing area, store, and staff utility spaces. Walls in kitchen and washing areas are finished with ceramic tiles, and floors are laid with anti-skid vitrified tiles. All plumbing lines are executed using CPVC/UPVC piping systems, suitable for commercial usage. Proper provisions for exhaust, ventilation, and service shafts are integrated within the wall and ceiling layouts." "Toilets are laid with vitrified tiles, and the external deck area is made of thermo pine wood finished with weather-protective coatings. Doors are made of laminated flush doors, and windows/sliding doors are of UPVC sections fitted with 5 mm toughened glass. Options for double glazing units and mosquito mesh are available at extra cost. Skylights can also be provided in the roof structure if required. Electrical fittings include internal wiring with R R Kabel and fittings like switches/sockets of Legrand make and LED lights of Jaquar/Philips. Provisions for air-conditioning pipelines are embedded within wall layouts. INlducing electifcal fitures too " Decks are finished with 90×90 mm thermo pine balusters and 10 mm thick toughened glass inserts, with handrails made of 140×26 mm thermo pine sections, providing a secure yet transparent enclosure for the front deck areas. The structure includes two identical rooms of 10'-9" × 13'-6", each with an attached toilet (10'-9" × 5'-0") and a front-facing 11'-0" × 6'-0" deck space. The total covered area of the cottage is 592 square feet. All structural and finishing works shall be executed in compliance with the direction of the Engineer-in-Charge, adhering to the approved architectural and technical drawings. The cost of substructure is inclusive The cost is inclusive of preparation of shop drawing and sample approval as per Architect in charge. The above mentioned finishes, makes of all items are subject to final approval by sample procurement and submission from any leading vendor to the Architect in charge. Cost of Multipurpose Hall PEB of min area of 950 SQM inlduing ht ePEB strcture, finishes as per Architect in cahrge

SITC of G+1 Prefabricated Twin Room Cottages, designed as a hybrid prefabricated structure using Light Gauge Steel Framing (LGSF) techNoslogy, with primary structural sections imported from Australia and secondary mild steel load-bearing members precision-fabricated SITC of Prefabricated Admin and Cafeteria Building, designed as a hybrid structure using Light Gauge Steel Framing (LGSF) techNoslogy, imported from Australia, incorporating mild steel load-bearing sections fabricated using CNC machines. The structure is engineered to withstand wind speeds of up to 180 kmph and is suitable for Seismic Zone IV. The RCC substructure up to plinth level, including foundations, pedestals, and plinth beams, shall be constructed as per approved structural drawings, over which the prefabricated steel superstructure shall be installed. The cost is inclusive of structural design for the substructure, based on site inputs received from the Architect and Structural In-Charge, designed as per Indian Codes and Standards. Construction of RCC up to plinth level is inclusive. Superstructure, Walls & Cladding The external walls of the building are clad with thermo pine wood planks, providing aesthetic warmth and weather resistance. The claddings are pre-treated and coated with weatherproof oils and are fixed over 10 mm thick OSB (Oriented Strand Board) sheets. The structure is further wrapped with waterproof and termite-resistant OSB panels from both inside and outside for additional protection and durability. Internal partitions are formed using the same LGSF system, sheathed with OSB boards and finished with gypsum boards. The roof system is constructed using asphalt shingles manufactured by TechNosNICOL Corporation, installed over a lightweight steel framing system. These shingles carry a 50-year manufacturer warranty and provide excellent resistance against heat, rain, and water ingress. Provision for skylights within the roof structure can be incorporated if required, at an additional cost.The structure is further wrapped with waterproof and termite-resistant OSB panels from both inside and outside for additional protection.The roof is constructed using asphalt shingles manufactured by TechNosNICOL Corporation, supported over a lightweight framing system. These shingles offer a 50-year warranty and provide excellent resistance against heat and water ingress. All internal walls and ceilings are finished with gypsum board over OSB panels and painted in the client’s choice of colour. Bathroom walls are tiled with ceramic tiles from Kajaria, and the toilets are fitted with high-quality sanitaryware from Kohler and Jaguar, including WC, washbasins, faucets, and other essential fixtures. All internal plumbing lines are made of CPVC/UPVC. The flooring in rooms is finished with indoor-grade wooden laminate flooring from Greenply, offering multiple colour options. ( Complete In all respect). Decks are finished with 90×90 mm thermo pine balusters and 10 mm thick toughened glass inserts, with handrails made of 140×26 mm thermo pine sections, providing a secure yet transparent enclosure for the front deck areas. The structure includes two identical rooms of 10'-9" × 13'-6", each with an attached toilet (10'-9" × 5'-0") and a front-facing 11'-0" × 6'-0" deck space. The total covered area of the cottage is 592 square feet. All structural and finishing works shall be executed in compliance with the direction of the Engineer-in-Charge, adhering to the approved architectural and technical drawings. The cost of substructure is inclusive The cost is inclusive of preparation of shop drawing and sample approval as per Architect in charge. The above mentioned finishes, makes of all items are subject to final approval by sample procurement and submission from any leading vendor to the Architect in charge. (makes Loomcraft/ or equivalent) "Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. “All above operations to be done in order and as directed and specified by the Engineer-in-Charge”:With average thickness of 120 mm and minimum thickness at khurra as 65 mm"

Float glass panes 4 mm thick glass pane (weight not less than 10kg/sqm). (DSR -9.7.7.1)

Supply of DLP Laser projector, Brightness: Min 19000 Lumens, Native resolution: WUXGA (1920 x1200) or more. Input Resolution support : 4K or better, Contrast: 100000:1 or more; Sealed core optics, Brightness Uniformity: 90% or more; Illumination Lifetime: 20000 Hrs or more ; Inbuitl Warping & Blending; Stereoscopic 3D support for future 3D shows; Inputs: 2 x HDMI 2.0, DP 1.2, HDbaseT,VGA. Operating temperature: 0-50 degC . Compact & Light Weight: 50Kgs or less. Should be supplied with appropriat long throw lens as per site requirement. TAA certification required ( Complete In All respect ) (NSR)

Supply of Smart light weight outdoor projector enclosure suitable for Marine environment made of Aluminum with Aluminum wielding. Complete with:Build to meet minimum IP64 weatherization standards.Anti-reflecting tempered glass window with 94% transparency provided for an uninterrupted projection.Hydrophobic filter for salt fog filtering.Powerful AC fan for efficient cooling with positive pressure for ultimate projector protection. Fan circulation to automatically start even during day time if inside temperature goes above 35 deg Cel. Sensor based Humidity and temperature control automation to provides complete climate control inside the enclosure automatically. Enclorure unit to be Insulated with non fibrous, non toxic Cross linked polyethylene sheets with min. 19mm thickness Complete unit to be powder coated and insulated for heat protection. Power distribution sockets 16/6 Amps and industrial plug 32A.( Complete In All respect ) (NSR)

Designing,Fixing and intallation of projectors,with suitable MS base plate of 10mm, clamps, grouting material, painting and other accessories.( Complete In All respect ) (NSR)

Supply of Media Server with associated software license and hardware . The display server should have 4 DP 1.4v outputs with each channel supporting 4k@60, 4.4.4The hardware should have 16GB RAM System memory, min. 1TB High Performance SSD Drive Storage. The hardware should have dedicated 6GB GPU and 1GBP/S ethernet port with 2 USB3 ports,3.5 mm stereo output jack and should support genlock, geometry correction, edge blending, color correction and 2D/3D mapping. The OS for the server should be Windows 10 enterprise embedded with quick OS recovery built-in.( Complete In All respect ) (NSR)

Supply of Show Control software complete with necessary software and hardware interface including lifetime license and accessories.( Complete In All respect ) (NSR)

Supply of All-Weather Loudspeaker with 15" LF ,Frequency Range (-10 dB): 35 Hz – 20 kHz, Frequency Response (±3 dB): 55 Hz – 19 kHz ,Coverage Pattern: 90° x 50°, Long-Term System Power Rating: 600 W (2400 W peak), Sensitivity (2.83V @ 1m): 100 dB ,Maximum SPL: 128 dB (peaks of 134 dB), Crossover Frequency: 1.2 kHz, Nosminal Impedance: 8 ohms ,Transformer Taps: 70V: 400W, 200W, 100W. 100V: 400W, 200 Environmental: IP55 as per direction given bt engineer in charge.( Complete In All respect ) (NSR)

Supply of Subwoofer Dual 18 Inches of Frequency Range (-10dB): 28 Hz – 1 kHz, Frequency Response (±3 dB): 35 Hz – 1 kHz, System Power Rating: 1600 W (6400 W peak), Sensitivity 102 dB , Maximum SPL (1m) 136dB, 142 dB Peak, Nosminal Impedance 4 ohms , IPX3, 4 Inches Voice Coil. (NSR)

Supply, of Two-way Small Format high SPL IP55 rated (as per IEC 60529) all weather surface mount loudspeaker. The louspeaker shall meet the following performance criteria: Frequency Range (-10 dB) of 80 Hz - 20 kHz or better; Nosminal Dispersion : 120°H x 120°V; Power handling of 200cW or more; Sensitivity : 94 dB; Max SPL : 123dB Peak; Nosminal impedence of 8 ohms. The loudspeaker system shall be comprised of a Powder-coated finish stainless steel grille with Two-part spray polyurea coating Enclosure; Single 8-inch woofer; Single 2-inch voice coil high-frequency compression driver; U bracket. ( Complete In All respect ) (NSR)

Supply of Multichannel Digital Network Based Power Amplifier with Power output 4 x 1250W @ 4 Ohms / 8 Ohms, Four-channel Audio amplifier, 4x 1250W at 4 and 8 Ohm, 70Vrms and 100Vrms output on all Four channels, THD (at full rated power, 20Hz - 20kHz) =0.35%, Cooling Continuously variable speed forced air, Voltage Gain Max level= 34dB, Audio Digital channel bus compatibility up to 8 channel, bridgeable channels - even in 100Vrms mode, 2 digital audio bus RJ45 port, 1 Ethernet RJ45 port for monitoring and configuration, Should have Limiters , Input/output EQ , Delay ,Matrix Mixer ,Speaker Line impedance Monitoring, Damping Factor (20 Hz to 100 Hz) : >1500 (NSR)

Supply, installation, testing & Comissioning of Multichannel Digital Network Based Power Amplifier with Power output 8 x 600W @ 4 Ohms / 8 Ohms, Four-channel Audio amplifier, 8x 600W at 4 and 8 Ohm, 70Vrms and 100Vrms output on all Four channels, THD (at full rated power, 20Hz - 20kHz) =0.35%, Cooling Continuously variable speed forced air, Voltage Gain Max level= 34dB, Audio Digital channel bus compatibility up to 8 channel, bridgeable channels - even in 100Vrms mode, 2 digital audio bus RJ45 port, 1 Ethernet RJ45 port for monitoring and configuration, Should have Limiters , Input/output EQ , Delay ,Matrix Mixer ,Speaker Line impedance Monitoring, Damping Factor (20 Hz to 100 Hz) : >1500 ( Complete In All respect ) (NSR)

Supply of 12 x 8 Networked Digital Signal Processor With AEC , Should have 12 floating AEC in group of 4 Ch SITC of DSP with 12 inputs and 8 outputs, 12 Control Inputs and 6 Logic Outputs for GPIO Integration, 48V phantom power on all analog inputs, THD: <0.01% 20Hz to 20KHz, +10dBu output, Crosstalk: <-75dB, Open architecture software configurable, Separate logic processing power ,2 digital audio bus RJ 45 Port , 1 Ethernet port for Monitoring and configuration , Capable to handle +5V unloaded logic output voltage ,Should have speech filter engine , Capable to control 3rd party devices with TCP IP and RS 232 , Should have 1Nos of RS 232 port for integration with control System, Should have Bi-Directional Locate Functionality ,Should have 48 or more digital audio Channel Bus, Should have monitoring LED for COM, STAT, ERR and PWR ( Complete In All respect ) (NSR)

Screen Estblishing & Content Generation, Designing, Storyboarding, Historian/ Project Conservationist onboarding, Direction and Graphics, ArtisticDirection, research, script, translation, dramatization, Visualizing the content, creating 2D,3D animation, CGI, video shoot including artist, laser animation,Art component (ifany),Programming/integration of show with content,effect complete etc.as reqd.The work includes collection of required information & relevant data, development of content for illumination show in consultation with client and making changes as per the observations / requirements.Content should be of 15mins. (NSR)

Supply of Small Business 24 port Gigabit switch and 2 x Mini GBIC fiber uplinks. Standards:-IEEE 802.3, 802.3u, 802.3x, 802.3ab. Cabling Type:-Category 5 and multi-mode fiber. Power:-100-127VAC/200-240VAC, 1.0A/0.5A, 50-60 Hz. Operating Temperature:-32 to 104ºF (0 to 40ºC). (NSR)

Supply of Equipment Rack - 19 " , 27U standard Rack with all required accessories. Earthing community kit, mounting bracket, cable manager, support angle, equipment shelf, mounting hardware, fan housing units etc, Ventilated top and bottom covers with attractive styling. It has Removable side panels with slam latches for easy access. (NSR)

Installation, Testing & Comissioning of Audio system, Projector mounting,mapping, Alignment, blending, Projector & audio system Poles,complete project other items installation (NSR)

Supply , laying of all conduits, Audio, Video cables, TP/Fibreoptic cables, Fibre Optic HDMI cables/ TX-RX set for projectors -connectors & accessories as required form complete installation (NSR)

Supply, Fabrication & Installation of exterior directional sign board of size 750W X _ 1800H(Information panel) mounted on M.S. internal skeletal framework made out of M.S. box sections as detailed. All MS work should have one coat of primer and 2 | coats of Epoxy paint applied as per manufacturers instructions. The information panel shall be made out of 4mm thick Aluminium Composite Panel boxing of approved make and colour bent to curved/straight profile on both the sides as detailed. Graphic shall be printed on_ External Grade External Grade Vinyl and stuck to the main panel. The panel formed shall have overall minimum thickness of 90mm. The panel to have NLSIU Logo, Text in trilanguage, _— etc as detailed. The panel shall " be fitted 150mm above ground level. Exposed part of the panel grouted to the foundation shall be clad with Flame finish steel grey granite, all complete as per drawings, specifications & directions of Engineer In Charge. The rate quoted shall include the cost of scaffolding, fixing and grouting if any, etc. Cost for Excavation, Concrete and_ granite cladding shall be paid separately under their respective items. (NSR)

Supply, Fabrication & Installation of exterior directional sign board of size 750W xX _ 1050H (Information panel) mounted on M.S. internal skeletal framework . made out of M.S. box sections as detailed. All MS work should have one coat of primer and 2 coats of Epoxy paint applied as per manufacturers instructions. The information panel shall be made out of 4mm thick Aluminium Composite Panel boxing (Di-bond / Aluco bond or approved equivalent make) of approved colour bent to curved/straight profile on both the sides as detailed in the drawing. Graphic shall be printed on External Grade Vinyl and stuck to the main panel. The panel formed shall have overall minimum thickness _ of 90mm. The panel to have : NLSIU Logo, Text in trilanguage, etc as detailed. The panel shall be fitted 150mm above pround level. Exposed part of the panel grouted to the foundation shall be clad with Flame finish steel grey granite, all complete as per drawings, specifications & directions of Engineer In Charge. The rate quoted shall include the cost of scaffolding, fixing, grouting and grouting if | any, etc.Cost for Excavation, Concrete and granite cladding shall be paid separately under their respective items. (NSR)

Over all Size: Height -240 inch, Width - 46 inch, Depth - 12 inch Exterior moNoslithic double sided signage fixed with the help of MS pipe frame work cladded with 3mm thick Aluminium composite panel (ACP) duly cut by CNC router with 5mm/12mm imported A- cast “Acrylite” make acrylic fixed with 040 acrylic sheet on back with exterior grade vinyl text, illumination with backlit water proof IP-68 rated LED inside for individual letter illumination complete in all respects as per design. The Foundation work with reinforcement: Foundation Size 5 ft (L) x 3ft (W) x 5ft (D) (12 mm & 10 mm dia reinforcement steel @ 150mm bothways as per approval of Engineer-in-Charge, to be used in foundation with grouting of MS base plate (16 mm thickness) with the help of 20 mm dia grouting bolt of length Nost less than 450mm. The Nosminal mix concrete of mix proportion 1:1.5:3 to be used in foundation. The MS Structure to be erected over 16mm thick MS base plate. The 2 Nos MS pipe of size 150 x 75 x 5 mm to be fixed over base plate suitably braced with MS pipe of size 150 x 75 x 5 mm in between (04 Nos: 01 Nos top, 01 Nos bottom and 02 Nos in between) . Framing of MS pipe of size 25x25x5 over existing braced structure to be made on both side and thereafter, 50x50x5 mm square pipe to be fixed on side of structure in such a way to make provision for opeing on one side for maintenance purpose . ACP sheet – 3mm ACP sheet as per color approved by Engineer-in-Charge : Both side with side coverage as per design,approved size and approved MS structure. The ACP sheet to be cut by CNC router as per exact letter size & logo and as per approval of mock-up plan. Illumination: Illumination of Nost less than 140 lumens per feet, color temperature 10,000 K with IP68 grade power supply of SAMSUNG or equivalent make. 1)Logo of approximate size 42" x 14" on both side. 2) 12mm solid acrylic sheet laser cut letters-"" 3) 5mm solid acrylic sheet laser cut letters - 4) 12mm solid acrylic sheet laser cut letters of letter size 7 5) 5mm solid acrylic sheet laser cut letters- Noste: 1) Matter on one side to be writen in Hindi font and on aNosther side in English Font. 2) Matter as per tentative lay-out given. However, before actual execution, the bidder to take prior approval of mock -up plan from Engineer-in-Charge.( Complete In All respect ) (NSR)

Supply, Fabrication & Installation of exterior Informatory signboard of size 450W X 450H / 450 dia mounted on 50 mm dia M.S. _ Pipe Medium (B-Class), with : one coat of primer and 2 coats of Epoxy paint applied as per manufacturers instructions as indicated. The information panel shall be made out of 4mm thick Aluminium Composite Panel _ of approved make = and colour as detailed in the drawing. Graphic shall be printed on External Grade Vinyl and stuck to : the main. panel, all complete as per drawings, specifications . & directions of Engineer In Charge. The rate quoted shall include the cost of scaffolding, fixing, sprouting and grouting if any, etc.Cost for Excavation, Concrete shall be paid separately under their respective ‘items. Top of board shall be 1950 from Finished floor level. (NSR)

Supply, Fabrication &| SQM Installation of cautionary signs of size as per | design made of 2mm thick Aluminium plate with Reflective External Grade Vinyl _ stickers, Fixed to surface using 3M tape, '__ including necessary surface cleaning, all complete as per drawings, specifications & directions of Engineer In Charge. The rate quoted shall include the cost of scaffolding, fixing, etc. (NSR)

Supply, Fabrication & Installation of wall mounted SIGNAGE Individual Room Signage of size 450mm x 250mm, formed out. of computer cut vinyl printed matter of approved colour pasted on to 6mm thk acrylic sheet and fixed to surface . using double sided tape, all complete as per drawings, specifications & directions of Engineer In Charge. The rate quoted shall include the cost of scaffolding, fixing, etc. (NSR)

Supply, Fabrication & Installation of Informatory index signage of size 150mm x 200mm (wash rooms) formed out of computer cut vinyl graphic as per approved design and pasted on 6mm thk acrylic sheet and fixed to surface using double sided tape, all complete as per drawings, specifications & directions of Engineer In Charge. The rate quoted shall include the cost of scaffolding, fixing, etc. (NSR)

Supply, Fabrication & Installation of wall mounted index signage of size 450mm x 300mm, formed out of computer cut vinyl graphic as per approved design and pasted on 6mm thk acrylic sheet and fixed ‘to surface using double sided tape, all complete as per drawings, specifications & directions of Engineer In Charge. The rate quoted shall include the cost of scaffolding, fixing, etc. acrylic sheet with suitable arrangement to slide in the name of the occupier, and fixed to surface using double sided tape, all complete as per drawings, specifications & directions of Engineer In Charge. The rate quoted shall include the cost of scaffolding, fixing, etc (NSR)

Supply, Fabrication Installation of wall mounted | index signage of size 450mm x 300mm, formed out of computer cut vinyl printed matter of approved font size and colour. The signage shall be mounted on 6mm thk acrylic sheet and fixed to surface using double sided tape with 15 mm. thick modular aluminium frame and backing, all complete as per drawings, specifications & directions of Engineer In Charge. Signages are to be mounted on surfaces using double sided tape. Supply, Fabrication & Installation of wall mounted signage of size as required, formed out of 6 mm thk acrylic plastic of approved colour. The signage shall be mounted on to surface using double’ sided _ tape, all complete as per drawings, specifications & directions of Engineer In Charge. The rate quoted shall include the cost of scaffolding, fixing, etc. (NSR)

Supply, Fabrication & Installation of wall mounted signage of size as required, formed out of 4 mm thk ACP of approved colour. The signage shall be mounted on to surface using double sided tape, all complete as per drawings, specifications & directions of Engineer In Charge. The rate quoted shall include the cost of scaffolding, fixing, etc (NSR)

Supply, Installation, Testing, and Commissioning (SITC) of a high-definition LED display system using Flip-Chip MicroLED COB technology. The display is designed with a requested screen size of 10.00m by 2.1m, with a suggested final size of 19.80m by 0.68m. The screen resolution is set at an impressive 12,672 pixels in width by 432 pixels in height, ensuring sharp and detailed visuals. The display is composed of aluminum (AL) cabinets arranged in a grid of 33 units across by 2 units high. No spare cabinets are required for this setup. Control of the LED display will be managed by a Novastar All-in-One 4K Prime controller, supported by a Novastar TB40 controller, providing seamless operation and high-quality output. The tender also includes 8 spare modules and 3 HUB boards to ensure quick replacements and maintain system integrity. Packaging for the components will be provided in 8 polywood boxes, ensuring safe transportation and storage.The installation will involve connecting the main power through a 3-phase cable to the nearest power distribution room, as per site requirements. Additionally, a fiber cable will be laid from the control room to the display system, accompanied by a power distributor box and signal fiber cable for efficient power and data transmission. An equipment rack will be provided to house the controllers, ensuring organized and secure placement. The system also includes a Content Management System (CMS) with a 3-year license, enabling easy and flexible content delivery and management. The tender specifies the fabrication and installation of a Mild Steel (MS) structure on-site to support the LED display, ensuring stability and precision alignment during installation. This comprehensive specification covers all necessary components and details to ensure a high-performance LED display system, fully integrated and ready for use. ( Complete In All respect ) Technical Specification: LED display system with high-resolution and efficient performance characteristics. The display system features modules with a pixel pitch of 1.5mm, utilizing Flip-Chip MicroLED COB technology for superior image quality and durability. Each module has a resolution of 300 x 168.75 pixels and a size of 192mm x 108mm, with a weight of 0.43 kg. The display cabinets, made from die-cast aluminum for durability and lightweight, measure 0.60m x 0.34m with a thickness of 30mm. Each cabinet houses 4 modules, resulting in a cabinet resolution of 384 x 216 pixels and a pixel density of 82,944 pixels per cabinet. The cabinets are designed for front-access maintenance, simplifying any future service needs. The display system is equipped with automatic brightness control, offering a white balance brightness of ≥1000 cd/m², and supports a color temperature range of 6000K to 10000K. The best viewing distance for this high-resolution display is ≥1.5 meters, ensuring sharp and clear visuals even from close range. The system ensures over 95% brightness and color uniformity, with a protective grade of IP43, making it suitable for indoor applications. The display also offers a wide viewing angle of 160° both horizontally and vertically, and maintains a low defects rate of ≤0.0002. The frame frequency is set at ≥60Hz with a refresh rate of 3840Hz, ensuring smooth video playback. The system operates on an input voltage of 200-240V AC ±10%, with a maximum power consumption of 350W per square meter and an average power consumption of 117W per square meter, reflecting its energy efficiency. Designed to operate in a wide temperature range from -30°C to +60°C and humidity levels between 10%-95%, the display system promises a long lifespan of over 100,000 hours, ensuring reliability and longevity. (NSR)

Supply, Installation, Testing, and Commissioning (SITC) of 65" Capacitive Interactive Wayfinding Kiosks, complete with stands, tailored for use in mall environments as per design and drawing aprpoved by Architect in charge. The kiosks will feature an Android-based solution, equipped with a 10-touch capacitive screen for an enhanced user experience. Each kiosk will include 4GB of RAM and 32GB of internal storage, supporting a 16:9 aspect ratio and a high contrast ratio of 5000:1, ensuring clear and vibrant display quality. The screen will be protected by 4mm tempered glass, providing durability and safeguarding against potential damage. Connectivity and input options include dual WiFi, four USB 2.0 ports, one HDMI port, one VGA port, audio output, microphone input, two built-in speakers, and an RJ45 Ethernet port, ensuring versatile connectivity options for various applications. Also includes the cost of licensing the screen kiosks, with a subscription fee per unit per year, ensuring continued access to the necessary software and support services. Packaging and transportation of the kiosks will be managed using secure wooden boxes to prevent damage during transit. The project scope includes conducting trials and providing comprehensive training to the mall staff to ensure effective usage and maintenance of the kiosks. Power connections will be provided up to each kiosk location, along with the installation of LAN cables for network connectivity. If required, a power distributor box and signal fiber cable will be installed to support the kiosk’s power and data needs. Additionally, an equipment rack will be supplied to house the necessary controllers, and a network switch will be included to facilitate reliable and efficient networking of the kiosks.( Complete In All respect ) (NSR)

Providing & fixing Cobble Stone Flooring (11X11X10)cm filling of joints in 1:3 Cement mortar and stone aggregate with matching colour pigments all complete specification & direction of Engineer in charge. (NSR)

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-in-charge. (The panel shuttering work shall be paid for separately

ACI (HIGH PERFORMANCE STAMPED CONCRETE) Applying and finishing the top surface of concrete, in accordance with sprinkling of ACI color hardener at the rate of 0.31 kg./sq.ft., Floating the surface with different types of floaters, application of release agent at the rate of 0.011 kg./sq.ft , stamping the concrete with stamping tools, cleaning the surface with water and application of acrylic based sealer at the rate of 0.035 ltr/sq.ft, for finishing. Complete for play area, parking areas, Compound flooring, Podium, Basement flooring, External roads etc. (NSR)

Fixing & supplying of Landscape edging designed with the highest end 304 Stainless Steel, to never rust or corrosion free , customised in 'L' shape with mounting spikes on one side with each unit's fixing based on iinterlocking machanesim with height 8" & Thickness (gauge) is 0.02" Steel spikes are 3.9" long (1 per foot)​ (Make Zudoo/haofy) (NSR)

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres. (DSR -16.1)

Construction of dry lean cement concrete sub base over a prepared subgrade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineer-in- charge. (DSR -16.8)

Construction of granular sub-base by providing close graded Materia conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30 (DSR -16.78.2)

Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately).Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately. (DSR -16.43.1)

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineerin- charge (length of finished kerb edging shall be measured to calculate volume for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). (DSR -16.69)

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-in-charge. (The panel shuttering work shall be paid for separately (NSR)

SITC of Dry Deck Fountain on a floor of 15 sq.mtr. 10 nos. flush mounted jets, fitted on a 50mm dia Pipe (15 mtr. length) – SS304 with accessories like flanges,sockets, etc. Nozzles are made of Brass- Chrome Plated. 10 nos. of Gate valves for nozzles, with 3" NRV of C.I. on pumpset delivery (Sant/Zoloto/Leader make ISI Mark), Height of water effects - 2mtr., Make of fountain: ALT/A.M. Irrigation System/Bharat Engineers

SITC of Waterproof Lights, Waterproof 12V LED lights (RGB/White). Complete light body made of Stainless, steel 304 grade, total 27 watt power leds. Toughened glass with seal. Stainless steel 304 grade, cable gland. All external nuts and bolts are of Stainless steel 304 grade., Adjustable mounting bracket is made of Stainless steel 304 grade. IP 68, compliant. Light complete with clamp, waterproof hardener & epoxy. All 'in pool' connections, shall be fully waterproof. Make of Lights: ALT/A.M.Irrigation System/Bharat Engineers.

Providing & laying of 1.1 kV grade double insulated copper flexible cable 2.5 sq.mm x 3 core (100 mtr), 1.5 sq.mm x 4 core (500 mtr) & 1.5 sq.mm x 2 core (500 mtr) for pump, S. Valve & Light (150mtr), Make: Finolex/Havells/Polycab (NSR)

SITC of Solenoid Valves (10 Nos of 40mm): Fast acting solenoid valves with extremely fast operation and minimum obstruction for a high flow rate. These valves are best suited for adaptability and variability for fast movement in fast beat songs. Material of construction of Solenoid Valves: Stainless steel (SS-304). IP-68 Weather Proof Coil 24V DC. (make of S. Valves: ALT/A.M.Irrigation System/Bharat Engineers/Uflow) (NSR)

SITC of LED Light & SoleNosid Valve Panel: Mild steel (Epoxy powder coated) enclosure made from 16 SWG Mild Steel sheet consisting of necessary channels for 12V RGB LED Lights and 24V soleNosid valves, Digital Volt and Amp. meter, necessary quantity of 12V & 24V suitable wattage meanwell SMPS, Switch Gear From Schneider and Phoenix contact. Make of panel: ALT/A.M.Irrigation System/Bharat Engineers/Paai (NSR)

SITC of 1 no. Monoblock type submersible pump set of 7.5HP, (Three phase, 50Hz, 415-380V AC) with proper completion of work as per direction of E/Ic, Pump: Kirloskar/Crompton Greaves/Texmo Make. Suction filter for pump: Filter body & filter, mesh made from AISI 304 standard stainless steel. Make of Filter:ALT/A.M.Irrigation System/Bharat Engineers

Earthing of Fountain's electrical panel (NSR)

FLOATATION SYSTEM -HDPE Pontoon is a unique dry dock system accessory, made from high density polyethylene using the blow molding method, with anti-corrosion, anti-freezing, anti- oxidation, and antiultraviolet characteristics. Its superior design prevents any disproportionate stress on the hull by distributing the weight of the boat more stable.Its environmentally friendly reinforced materials can avoid the erosion of seawater, chemicals, drugs,oil and water bodies. There size of HDPE pontoons, which are used 50x50x40 cm. The top surface of the pontoon has a pattern without sharp corners and a non-slip design to ensure safety and stability.The four rounded and blunt corners avoid hazards such as slipping, splintered wood splinters and rusty nails in concrete, wood and steel facilities. The modular is cubes, which are connected bypins, and can be equipped with special railings, fasteners, bolts according to the environment on site. with brackets & all fittings. Frame made of SS304. (NSR)

AUTOMATED IRRIGATION SYSTEM (NSR)

Supply, installation of Landscape Works across the site inlduing plantatoin of all desired plants in desired heights as per Architect in charge. ( Complete In All respect ) (NSR)

Supply and fixing of TG RO43 BETA, powder coated Tree guard as per design approved by Architect in charge with the following specifications:The unit is in powder form, packed in a 5Kg drum for secure handling and transportation. The product features a cylindrical design made of mild steel, with a color-coated green finish for durability and corrosion resistance. It has an opening size of 2 inches, a mesh number size of 11-50, and measures 5 feet in height.The structure includes 3 legs with 4 ties for enhanced stability during use. Weighing 3.5 kg, the item is lightweight yet sturdy, ensuring easy handling and installation. It is made from galvanized material, adding to its longevity and resistance to environmental factors. (NSR)

SITC of 40W RGBL Source Wash Light with the Following Specification : Max Power - 40W, Voltage - AC100~240V, Minimum Light efficiency (lm/W) > 45 lm/w, Lumen/Kg > 1000 lm/kg, Minimum Lumen (Full Colour On) > 1800 lm, Minimum Lumen (RED) > 670 lm, Minimum Lumen (Green) > 1170 lm, Minimum Lumen (Blue) > 250 lm, Standard Optical System -12°/30°/45°/60°/12*50°/15*50°, Dimming - 24Bit, CCT - 1800K-10000K with 14 In-Built Presets, Fast Colour Pickup - 24 In-Built Presets, Impact Projection - IK10, Ingress Protection - IP67, Protocol - DMX + RDM, BIS (NSR)

SITC of 80W RGBL Source Wash Light with the Following Specification : Max Power - 80W, Voltage - AC100~240V, Minimum Light efficiency (lm/W) > 52 lm/w, Lumen/Kg > 1000 lm/kg, Minimum Lumen (Full Colour On) > 4500 lm, Minimum Lumen (RED) > 1250 lm, Minimum Lumen (Green) > 2050 lm, Minimum Lumen (Blue) > 450 lm, Standard Optical System -12°/30°/45°/60°/12*50°/15*50°, Dimming - 24Bit, CCT - 1800K-10000K with 14 In-Built Presets, Fast Colour Pickup - 24 In-Built Presets, Impact Projection - IK10, Ingress Protection - IP67, Protocol - DMX + RDM, BIS Make : Make : LBT / ARCTIK / CAMEO / Roxx Lighting (NSR)

SITC of stand alone DMX 1 x 512 controller of different DMX system from RGB/RGBW to more advanced moving and color mixing luminaries. The dual channel DMX 512 controller including RTC/calendar, Ethernet facilities, dry contact port triggering, multi-zone programming and SD memory card. The lighting levels, colors and effects can be programmed from a PC using the DMX software including following additional accessories etc. as required. Make : Lbt / Visual Production / Enttec / Cameo (NSR)

SITC of 1-universe, all-in-one DMX recorder , smart light show controller and playback controller for professional light shows and automated projects. The Reorder should be Art-Net / sACN Compatible and should have a Max refresh rate (FPS) of Art-Net & sACN: 60 / USITT DMX512-A: 44. The Device should have a Compliance of RCM (Aus/NZ), CE / WEEE (EU), UKCA (UK), FCC (USA).Make : Lbt / Artic / Visual Production / Enttec / Cameo (NSR)

SITC of lighting control system comprising high-performance industrial-grade control workstation with Intel i9 processor, minimum 16GB RAM, 1.5TB SSD storage, 4GB dedicated graphics card, and 24-inch Full HD LED monitor pre-loaded with licensed Windows 11 Pro operating system and compatible with DMX/lighting control software for programming, scheduling, and real-time operation of DMX based lighting fixtures system shall include all necessary interfaces, communication modules, power supplies, cables, and accessories, complete in all respects. Make :Dell/HP/Asus (NSR)

SITC of Ethernet to DMX converter With 2 Universes of bi-directional eDMX to DMX conversion and Art-RDM support. The Converter should support DMX -> Art-Net (Broadcast or Unicast) / DMX -> sACN (Multicast or Unicast), 0/100 Mbps of network speed And can Configurable DMX output refresh rate. The convertor should also be compitable with IEEE 802.3af PoE (Power over Ethernet).Make : Lbt / Artic / Visual Production / Enttec / Cameo (NSR)

SITC of 8-port, DMX/RDM isolated splitter with 7-24v DC power input range and removable terminal plugs for simple wiring. The Device should housed within a compact, electrically-insulated form factor with flexible mounting options. The Device should have Opto-isolation between each DMX port to protect against stray voltages on the DMX line and should support Support for DMX512-A. Make : Lbt / Liteputter / Visual Production / Enttec / Cameo (NSR)

Programming, testing, and commissioning of lighting system with multiple customized lighting scenarios and dynamic sequences for festivals, events, and national days as approved by the Authority,programming shall include creation of color themes, effects, timing schedules, and synchronized transitions using DMX lighting control software, ensuring smooth operation, recall of presets, and user-friendly interface, complete in all respects as required for approval and demonstration. (NSR)

SITC of Prefabricated Kiosks, designed as a hybrid structure using Light Gauge Steel Framing (LGSF) techNoslogy, imported from Australia, incorporating mild steel load-bearing sections fabricated using CNC machines. The structure is engineered to withstand wind speeds of up to 180 kmph and is suitable for Seismic Zone IV. The RCC substructure up to plinth level shall be constructed as per approved structural drawings, over which the prefabricated steel superstructure shall be installed. The cost is inclusive of structural design for the substructure, based on site inputs received from the Architect and Structural In-Charge and designed as per Indian Codes and Standards. Construction of RCC up to plinth level is inclusive. Superstructure & Wall System: The superstructure of the kiosk is executed using LGSF members, with external wall assemblies formed using 10 mm thick OSB (Oriented Strand Board) sheets fixed over the steel framing. The structure is wrapped with waterproof and termite-resistant OSB panels from both inside and outside to ensure durability and protection against environmental conditions. ( Complete In All respect ) (NSR) You said: "CNC Metal Façade: The external façade of the kiosk is finished with a custom-designed CNC-cut metal façade, fabricated from powder-coated / galvanized mild steel or aluminium sheets, as per the approved architectural design. The CNC panels are mounted on a secondary steel framework with a ventilation gap. The façade pattern, thickness, finish, and fixing methodology shall be as per approved shop drawings. Rolling Shutters & Openings Each kiosk is provided with rolling shutters fabricated from galvanized steel, complete with guide channels, locking mechanisms, and hardware. Shutters may be manual or motorized, as specified. Windows, where provided, are in uPVC or aluminium sections fitted with toughened glass, as per approved drawings." "Roof: The roof is constructed using a lightweight framed system over LGSF members with proper waterproofing treatment, suitable for all-weather usage. Internal Finishes: Internal walls are finished with gypsum boards over OSB panels, painted in the client’s choice of colour. Flooring is finished with vitrified / anti-skid tiles suitable for kiosk operations. Ceiling finishes, where applicable, are in gypsum board." "Branding and signage form an integral part of the kiosk design and include the following: Primary Signage Band integrated with the kiosk façade, fabricated from ACP / metal sheet / acrylic panels, with vinyl graphics or UV-printed branding, as per the approved branding guidelines. Backlit or front-lit signage, using LED modules, complete with diffusers, wiring, drivers, and concealed fixing systems. Logo panels fixed on CNC metal façade or dedicated signage frames, fabricated from acrylic / metal with laser-cut or routed profiles. Internal display panels, suitable for menus, information boards, or promotional content, made of ACP / MDF / acrylic, finished with vinyl or UV printing. Provision for digital display screens, including concealed conduits, power points, and mounting brackets (screens excluded unless specified). All branding artwork, fonts, colours, dimensions, and placement shall be as per branding manual / drawings approved by the Architect-In-Charge."

Providing and fixing Alumunium system/ or equivalent window T6306 grade alumunium 3 tracK sliding window ,with fixing and 5 mm toughened glass, powder coating in desired shade and design as aprpoved by Architect in charge including the cost of necessary fittings, fixtures, handles etc. as required to the complete satisfaction of Engineer in charge (NSR)

Providing and fixing 18mm thick Granite stone work for wall lining at all height in cement mortar 1:3 (1cement : 3 coarse sand) including pointing with white cement mortar with an admixture of pigment to match the granite shade complete as per direction of Engineer-in-charge. (NSR)

Providing and fixing in position to wall at required location, GRC / GRG (Glass reinforced concrete/gypsum) Panel 25-30 mm thick with making moulds to make design given by architect, making panels, fixing on walls etc. with all leads & lifts and as directed by Project Architect. complete in toto. (NSR)

Design, Fabrication, Supply, Installation, Testing and Commissioning of Single leaf Electrically operated Sliding gate suitable for a clear opening of 12.1 mtrs clear width and 1.8mtr clear height, over all width of 14.0 mtr min as per following specifications suitable for movement on track of MS Solid bright bar fixed on C channel i/c complete civil works for installation of gates and all associated works etc. complete as required. a. Outer main frame will be M.S rectangular/square section of size 100X100X3.0 mm thickness. b. Vertical and horizontal support pipe will be M.S rectangular section of size 100X50X3.0 mm thickness. c.Cross supports for wheel will be of M.S rectangular section with suitable size and thickenss. d. Top supports will be M.S rectangular section of suitable size . e. M.S wheels of 125 mm dia/suitable size and design with double ball bearing, self lubricated bearings f. Shaft of wheels and bracket as per site requirement g. Coupling arrangement as required at site. h. Double railing of suitable size with hole fast and 25 mm dia solid bright bar. i.Drive unit with suitable capacity 3 Phase motor of minimum 1 HP with suitable gear assembly as per site requirement. Limit switches/sensors etc.. control panel for operation, control wires of suitable size between drive unit and control panel including Additional three station push button for operaton of opening and closing. j. Gate shall be fabricated as per the specifications and Painting with one coat of epoxy primer and two coats of polyurethane spray paint of approved colour and make etc.. complete as required. k. M.S angle of size 50X50X5 SWG in M.S U channel of size 100mmX50mmX5 SEG i/c cutting of bitumiNosus/concrete road, fixingof track with concrete, all electrcial necesaary works and making good the same as per site condition as per design adn drawing approved by Architect in charge ( Complete In All respect ) (NSR)

Planning, developing, providing, casting, placing, erecting, fixing, testing, final finishing and commissioning of parametrically outdoor artistic installationss and Tree Installation including the cost of Base: tree having a foliage of 2.4m with a height of 2.1m and a life size artistic installations and statue of sitting below the Kalpavrikhsa, also including the base and pedestal or any kind of civil work required for installation of the artistic installations. Preferable techniques to be used shall be metal forging, clay model and lost-wax casting depending upon the detail required. The tree artistic installations has to be handcrafted and multiple pieces and sheets of steel shall be welede dif required, bent, and hand forged into required shape, Stainless Steel Product Specification Thickness 0.8to2 mm Color: Brass/Rose gold or as specified by Architect Surface Treatment: PVD Coated Brand: NewLine SteeL/ or equivalent Material: Stainless Steel Steel Grade: SS304 L Material Grade: 202,304 Finish: PVD Coated of required shape, size, posture, expression, gesture, design including costume and accesNSRies on the basis of research and development and approval of visual and or textual references to be done by the vendor and as per directions of the Consultant and Engineer-in-Charge. Also including the cost of casting, erecting of customized life size artistic installations, Size: width: 900mm, height: 830mm, depth:600mm Material: Bronze specified by Architect processed thorugh Lost-wax Casting process, Artistic Interpretation of artist performing Zari

Designing, engineering, fabricating, and finishing of parametrically evolved abstract 3dimensional Installation Tree Installation/canopies of size 3M dia and height of 4.5M or as specified having self-sustaining structure supported at base, fabricated in 10-12 mm Stainless Steel (304 Grade) Sheet/corten steel/FRP, using Laser Cutting, bending, welding and parametric assembly of open joints, and mirror finishing with PU coating/ or surface coating as desired at desired location as per approved drawing to the complete satisfaction of Architect in charge. Also including the cost of providing and fixing/erection at site complete to the entire satisfaction of the Architect, complete in all respects., including the cost of architectural lighting and other components as required. ( Complete In All respect )

Kid's Play Equipment

Resting Areas for Tourist (Benches) {NSR}

Providing & fixing of White Sandstone 1500mm length and 450mm and height 600 mm including foundation & support with all necessary T&P etc all complete as per design of direction in engineer/ Architect in charge. Also includes the cost of preparationof shop drawing, and sample preparation and approval from Architect in charge, Urban Litter Bins(NSR)

Providing & fixing of SS Dustbin size 487 x 399 x 1138 fixing on a foundation with base plate and wrapped with white/red sandstone from all sides of 75mm with all complete as per design of direction in engineer/ Architect in charge. Also includes the cost of preparationof shop drawing, and sample preparation and approval from Architect in charge, Drinking Water Provision Specification of Y-Drinking Water (Receiving, storing, handling, shifting, installation, testing & commissioning of WAE. AENosN.45.CHA Pou Water Station C.A, RO Processing Capacity 25LPH, size: 466X580X1445, Watt; 220v/50Hz, Cooling 480w, Hot 450W, net weight 110kg, in material SS 304, with 3 tap: Cold 20 Ltr,Ambient-25Ltr including all accessories complete in all respect etc.

Supplying and Fixing of Four Seater Arc Swing outdoor playing equipment including necessary fittings, T&P etc all complete in direction of engineer in charge.

Supplying and Fixing of Multi Seater See Saw outdoor playing equipment including necessary fittings, T&P etc all complete in direction of engineer in charge.

Supplying and Fixing of Turbo Tower outdoor playing equipment including necessary fittings, T&P etc all complete in direction of engineer in charge.

Supplying and Fixing of Curve Loop Climber outdoor playing equipment including necessary fittings, T&P etc all complete in direction of engineer in charge.

Supplying and Fixing of BALANCING BRIDGE (MODEL Nos- PGTH 03) outdoor playing equipment including necessary fittings, T&P etc all complete in direction of engineer in charge.

Supplying and Fixing of Four Seater MGR outdoor playing equipment (Make Arihant/ Kompain/ Funply) including necessary fittings, T&P etc all complete in direction of engineer in charge.

CCTV System: The cost is inclusive of preparation of shop drawing as per the design and idea approved by the Architect in charge and sample preparation and approval from the Architect in charge. , Supply and installation of 5MP IR Bullet outdoor UL Series Make : Honeywell/Bosch/Axis

Supply & Installation of 4 MP PTZ Camera Ul Seriers Make : Honeywell/Bosch/Axis

Supply and installation of 32 Channel NVR with 4 SATA with HDMI Make :

Supply and installation of 8TB HDD

Supply, Installation, Testing & Commissioning of Layer 2 8 Port POE+ with 1& 10G Portwitch requirement for CCTV . Make

Supply, Installation, Testing & Commissioning of Layer 2 10 Port Fiber Switch with 1& 10G Portwitch requirement for CCTV . Make

Supply & Installation 17U Rack with Chemical Earthing

Supply & Installation of 9U Industrial Outddor Rack

Supply, Installation, Testing & Commissioning of Cat-6 Mounting Cords 4 Feet for CCTV Jack Panel end as per given Specification etc. all complete.

Supply, Installation, Testing & Commissioning of Cat-6 Mounting Cords 7 Feet for CCTV Jack Panel end as per given Specification etc. all complete.

Supply, Installation, Testing & Commissioning of Cat 6 Outdoor Cable

Supply & Installation of 4 Core ARmtourd Cable

Supply & Installation of outddor joint box

Supply & Installation of 24Fiber LIU

Supply, Installation, Testing & Commissioning of 55'' inch Display for the CCTV Monitoring system

Supply & Installation of Fiber Patch Cord

Providing and supplying Full-range environmental loudspeaker with one downward firing 4.5" (114 mm), 360P Series II Frequency Response (-3 dB) 70 Hz – 10 kHz Frequency Range (-10 dB) 60 Hz – 15 kHz Coverage 360° × 50° Nosminal Impedance 4 Ω Power Handling, Peak 320 W in desiresd shade and finish as approved by Architect in charge.

Providing and supplying PowerShareX PSX2404D is a four-channel, 2400-watt smart amplifier designed for use with Bose Professional installed sound systems. Onboard DSP gives you instant access to optimized loudspeaker presets via ControlSpace Designer software with easy ecosystem integration across Bose Professional processors, loudspeakers, and controllers in desiresd shade and finish as approved by Architect in charge.

Providing and Supplying Features and Benefits 19-strand annealed bare copper conductors Semi-rigid PVC insulation Twisted, unshielded Riser rated PVC jacket NEC CL3R, CEC CMG, RoHS compliant in desiresd shade and finish as approved by Architect in charge.

Providing and supplying Music Streamer as approved by Architect in charge

Preparation of Shop Drawings, Testing and Commissioning complete as per Engineer in charge

Providing and supplying PA System with 16 Zone Controller with Mic & 4 Nos of Hon Speaker with 600 Mtr cable

Audio Rack 17U

Providing and supplying Turnstyle tripod as approved by Architect in charge

Providing and supplying 10 KVA Ups with Inbuilt Battery

Supply, Installation, Testing and Commissioning of ongrid Solar Photovoltaic Power Plant conforming to MNRE specifications as amended, consisting of MoNos/Poly Crystalline silicon solar cells, net metering facility, necessary protections, earthing, mounted on Aluminium/GI structure of suitable strength with following components complete as required:- a) Solar Photovoltaic Module of capacity 330 Wp or above, manufactured in India, conforming to IS 14286/IEC 61215, IS/IEC 61730-Part-1, IS/IEC 61730-Part-2. Solar Photovoltaic Module conversion efficiency shall Nost be less than 16.5%. PV modules used in solar power plants/ systems must be warranted for their output peak watt capacity, which should Nost be less than 90% at the end of 10 years and 80% at the end of 25 years. b) Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 400 V AC, three phase, 4 wire, 50Hz +/- 2.5 Hz, output voltage suitable to generate AC Power with efficiency Nost less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from 0 to 50 degree C. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage Frequency. c) Data Monitoring System complete with accessories. d) Fixing of Array junction box & Main junction box with IP 65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required. e) Lightning and surge voltage protection. f) Connections & Interconnections by supplying & fixing required size XLPE insulated copper conductor 1.1 kV grade armoured power and control cables between solar modules, main power cable to grid supply PCU unit along with supplying & fixing of necessary channel/conduit lugs and other accessories etc. as required.

Speaker Type Outdoor Colour Name green Peak Power Handling - Speakers 80 Watts RMS Power Range - Amplifiers 80 Watts Product Dimensions 43.18 x 40.64 x 40.64 cm; 6.6 Kilograms Item model number 40151 Manufacturer BOSE Item Weight 6 kg 600 g

Ideal for zone-expansion applications, Bose PowerSpace amplifiers enhance any premium commercial sound installation with clean, reliable power — and digital connectivity. A Bose AmpLink input allows for multiple channels of uncompressed, low-latency digital audio from Bose DSPs via a single Cat 5 cable. The PowerSpace P21000A provides 1000 watts per channel and features versatile outputs that give you the flexibility to deliver full channel power to either low- or high- impedance loads — without bridging — and even send double power to a single zone. For premium commercial applications, Bose PowerSpace amplifiers provide the power and performance to get the job done — pure and simple.

WiFi, Direct Streaming, Airplay, Spotify Connect and Bluetooth 5.0 wireless capability to your ampli ers, preamps and receivers. Mix and match any ombination of Kasper Streamers to create a custom multiroom system and play the same music throughout your home, send di erent sources to each room at the same time, or create your own custom-de ned multiroom zones... All controlled via our 4stream App

Speaker Wire 2.5mm

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required., Group A (DSR -1.10.1)

Wiring for twin control light point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required. (DSR -1.11)

Wiring for light/ power plug with 2X4 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No. 4 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable for loop earthing as required. (DSR -1.12)

Wiring for light/ power plug with 4X4 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 2 Nos. 4 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable for loop earthing as required. (DSR -1.13)

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required., 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire (DSR -1.14.1)

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire (DSR -1.14.2)

2 X 4 sq. mm + 1 X 4 sq. mm earth wire (DSR -1.14.3)

2 X 6 sq. mm + 1 X 6 sq. mm earth wire (DSR -1.14.4)

2 X 10 sq. mm + 1 X 6 sq. mm earth wire (DSR -1.14.5)

Supplying and drawing following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required., 3 x 1.5 sq. mm (DSR -1.17.3)

2 x 2.5 sq. mm (DSR -1.17.11)

2 x 4 sq. mm (DSR -1.17.20)

2 x 6 sq. mm (DSR -1.17.29)

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required., 20 mm (DSR -1.21.1)

25 mm (DSR -1.21.2)

32 mm (DSR -1.21.3)

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required., 5/6 A switch (DSR -1.24.1)

2 way 5/6 A switch (DSR -1.24.2)

15/16 A switch (DSR -1.24.3)

3 pin 5/6 A socket outlet (DSR -1.24.4)

6 pin 15/16 A socket outlet (DSR -1.24.5)

Telephone socket outlet (DSR -1.24.6)

TV antenna socket outlet (DSR -1.24.7)

Bell push (DSR -1.24.8)

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. (DSR -1.25)

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc. as required., 1 or 2 Module (75 × 75 mm) (DSR -1.27.1)

3 Module (100 × 75 mm) (DSR -1.27.2)

4 Module (125 × 75 mm) (DSR -1.27.3)

6 Module (200 × 75 mm) (DSR -1.27.4)

8 Module (125 × 125 mm) (DSR -1.27.5)

12 Module (200 × 150 mm) (DSR -1.27.6)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. (DSR -1.32)

Installation, Testing and Commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS/HFFR PVC insulated, copper conductor, single core cable etc. as required. (DSR -1.44)

Installation, Testing and Commissioning of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required, Upto 450 mm sweep, 510 mm sweep (DSR -1.50.2)

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes. (DSR -1.51)

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required., Group A (DSR -1.55.1)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings). (DSR -1.56)

Supplying & fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required. (DSR -1.57)

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, Ics=100% Icu and Operational Voltage 690V etc. as required. , 100 A, 16 KA, TP MCCB (DSR -2.2.1)

125 A, 16 KA, TP MCCB (DSR -2.2.2)

150 A, 16 KA, TP MCCB (DSR -2.2.3)

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator), 6 Way, Double Door (DSR -2.3.1)

8 Way, Double Door (DSR -2.3.2)

12 Way, Double Door (DSR -2.3.3)

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)., 4 Way (4 + 12), Double Door (DSR -2.4.1)

6 Way (4 + 18), Double Door (DSR -2.4.2)

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required., 8 Way (4 + 24), Double Door (DSR -2.5.2)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required., Single Pole (DSR -2.10.1)

Double Pole (DSR -2.10.3)

Triple Pole and Neutral (DSR -2.10.5)

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required., 63 A (DSR -2.14.3)

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required., 63 A (DSR -2.15.3)

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with two numbers GI Suspenders i/c base of suitable size GI angle, GI bolts & nuts, fastner etc as required., 100 mm width X 50 mm depth X 1.6 mm thickness (DSR -4.6.1)

150 mm width X 50 mm depth X 1.6 mm thickness (DSR -4.6.2)

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with two numbers GI Suspenders i/c base of suitable size GI angle, GI bolts & nuts, fastner etc as required. , 100 mm width X 50 mm depth X 1.6 mm thickness (DSR -4.7.1)

150 mm width X 50 mm depth X 1.6 mm thickness (DSR -4.7.2)

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with two numbers GI Suspenders i/c base of suitable size GI angle, GI bolts & nuts, fastner etc as required. , 100 mm width X 50 mm depth X 1.6 mm thickness (DSR -4.8.1)

150 mm width X 50 mm depth X 1.6 mm thickness (DSR -4.8.2)

Earthing with G.I. earth pipe 4.5 Meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. (DSR -5.2)

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 Meter long etc. with charcoal/ coke and salt as required. (DSR -5.6)

Supplying and laying 6 SWG G.I. wire at 0.50 Meter below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required. (DSR -5.7)

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required. (DSR -5.1)

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required. (DSR -5.11)

Supplying, Installation, Testing and commissioning of Passive Infrared (PIR) technology based occupancy sensor having high performance, non regulating programmable type, suitable for connected load upto 10Amp , for mounting height up to 3 meter and for 5 m diameter coverage area along with necessary fixing arrangements i/c programming at site etc. complete as required. (DSR -7.1)

Supplying, Installation, Testing and commissioning of Astronomical time switch of following configuration to be mounted in feeder pillars / Lighting DBs for automatic switching On & OFF of street lights at sun set & sun rise or twilight(Auto ON, Auto OFF, Auto modes) with manual override facility with 12/24 hour display format with suitable battery and indication for relay status i/c programming at site complete as required., 3 output(1output per phase) and suitable for three phase supply (DSR -7.4.3)

Brush Less Direct Current (BLDC) Fan without Remote Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal( Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, suitable for operation with regulator for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 0C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply, Ceiling Fan compliant to IS 374:2019 fan i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required., 1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum) (DSR -9.2.3)

Supply of 1.1 kV grade Aluminium conductor, PVC insulated & PVC sheathed / XLPE insulated, PVC sheathed, armoured underground power cable conforming to IS 7098(Part I), suitable for laying in ground/duct/tray as required, complete in all respect., 4C × 16 sq.mm (NSR)

4C × 25 sq.mm (NSR)

4C × 35 sq.mm (NSR)

3.5C × 50 sq.mm (NSR)

3.5C × 185 sq.mm (NSR)

3.5C × 300 sq.mm (NSR)

Supply of 1.1 kV grade Copper conductor, armoured, PVC insulated & PVC sheathed / XLPE insulated, PVC sheathed underground power cable conforming to IS 7098(Part I), suitable for laying in ground/duct/tray, complete as required.3C x 1.5 sq.mm (NSR)

7C x 1.5 sq.mm (NSR)

3C × 2.5 sq.mm (NSR)

4C × 4 sq.mm (NSR)

4C × 6 sq.mm (NSR)

4C × 10 sq.mm (NSR)

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required., Upto 35 sq. mm (DSR -10.1.1)

Above 35 sq. mm and upto 95 sq. mm (DSR -10.1.2)

Above 95 sq. mm and upto 185 sq. mm (DSR -10.1.3)

Above 185 sq. mm and upto 400 sq. mm (DSR -10.1.4)

Supplying and making cable route marker with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm X 60 cm at the bottom and 50 cm X 50 cm at the top with a thickness of 10cm including inscription duly engraved as required. (DSR -10.9)

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required. (DSR -10.1)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. , 3½ X 25 sq. mm (28mm) (DSR -11.1.20)

3½ X 35 sq. mm (32mm) (DSR -11.1.21)

3½ X 50 sq. mm (35mm) (DSR -11.1.22)

3½ X 185 sq. mm (57mm) (DSR -11.1.27)

3½ X 300 sq. mm (70mm) (DSR -11.1.30)

4 X 10 sq. mm (25mm) (DSR -11.1.32)

4 X 16 sq. mm (28mm) (DSR -11.1.33)

Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required, 100 mm dia (DSR -15.13.3)

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. 150 mm dia (DSR -15.14.2)

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. , 63 mm dia (OD-63 mm & ID-51 mm nominal) (DSR -15.16.1)

90 mm dia (OD-90 mm & ID-76 mm nominal) (DSR -15.16.2)

200 mm dia (OD-200 mm & ID-175 mm nominal) (DSR -15.16.5)

Supplying of Aluminum conductor PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following sizes, 3C x 300 sqmm AL Arm XLPE (NSR)

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required., Above 120 sq. mm and upto 400 sq. mm (DSR -22.1.2)

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required., Above 120 sq. mm and upto 400 sq. mm (DSR -22.2.2)

supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required: , 300 sq. mm (DSR -23.3.3)

Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required, 300 sq. mm (DSR -23.5.4)

Supplying and making straight through cable jointing with heat shrinkable jointing kit complete with all accessories including ferrules suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required , 300 sq. mm (DSR -23.6.4)

Supply, installation, testing and commissioning of following capacity (continuous loading) BEE 3 Star rated (Corresponding Level as per BIS amended upto date of receipt of tender) , 11/0.433 KV step down, 3 Phase, 50 Hz, Dyn 11 vector group, ONAN (Oil Natural Air Natural) copper wound transformer (Electrolytic grade 99.9% pure copper, Core made of first grade Cold Rolled Grain Oriented (CRGO) Core grade MOH or better, suitable for out door applications withOn Load Tap Changer (OLTC) on HV side having AVR relay and Remote Tap Changer Control (RTCC) for automatic sensing of incoming voltage, automatic operation of OLTC and facility for remote and manual operation of OLTC HV side in range of +5% to -15% in steps of 2.5%, having cable end boxes on HV side suitable for 3x300 sq.mm XLPE cable of 11 KV grade, including supplying and laying of copper conductor multicore control cable from transformer to HT breaker/panel for safety tripping, complete with all accessories and safety provisions as per relevant IS Code including first filling of filtered dehydrated oil, i/c supplying and grouting of suitable M.S. Channel with all accessories and transformer shall be confirming to IS : 2026 (Part 1 to Part 5), IS : 1180 complete in all respects etc as required at site. (500KVA Transformer) (NSR)

500 KVA DG Set, Supplying, Installation, Testing & Commissioning of ‘Silent Type Diesel Generating set as per CPCB IV + or better norms along with having Prime Power Rating of KVA as below, 415 volts at 1500 RPM, 0.8 lagging power factor at 415 V suitable for 50 Hz, 3 phase system & for 0.85 Load Factor, including testing at factory and site with fuel, load for test and other necessary arrangements Complete as per specifications, should have QR code which should contain drawing, test report OEM manual,Geo- Tag of manufacturing location, rating plate as per relevant IS Code etc. Tourbocharged Diesel engine 4 stroke water cooled, multi cylinder, dynamically balanced fly wheel, electric start of suitable BHP at 1500 RPM suitable for above output of alternator at 40 0C, 50% RH & at 1000 Meter MSL , capable of taking 10% over loading for one hour after 12 hours of continuous operation. The engine will be with Electronic governor, Dry type Air filter with service indicator, first filling of engine fuel (after commissioning) lubricating Oil, Coolant and other consumables complete with all the required accessories, the Electronic governor shall be as per ISO 8528.The engine shall comply to the latest CPCB norms (CPCB IV + or better) and Conforming to BS 5514, BS 649, IS 10000, IS 10002, IS 13018 and as per approved by Engineering in charge (NSR)

HT Panel , Supply, installation, testing and commissioning of 11kV outdoor metal-clad ICOG HT panel, factory built and type tested, suitable for 3-phase 50 Hz system having 12kV insulation class and 26.3kA short-circuit withstand capacity. The panel shall be weather-proof, vermin-proof, fully compartmentalized kiosk type construction with copper insulated busbars, draw-out/fixed vacuum circuit breaker (630A/1250A as specified) with motorized spring-charged mechanism, resin cast CTs, PT (wherever applicable), numerical protection relay with OC/EF protections, multifunction energy meter, control & indication scheme, electrical and mechanical interlocking, space heater, illumination, and earthing bus. The panel shall be suitable for bottom cable entry and complete with cable termination arrangement, control wiring, glands, lugs, danger plates and mimic diagram. The work shall include relay settings, primary/secondary injection testing, commissioning and submission of all test certificates, drawings and reports, complete in all respects as per relevant IS/IEC standards and engineer-in-charge approval. (NSR)

Feeder Panel, Supplying, erecting, testing and commissioning outdoor duty floor mounted weather proof IP66 feeder pillar fabricated as detailed above but with double door (lockable outer door), sloping roof, water run-off gutter on three sides as per approved drawing, entire unit mounted on 50mm x 50mm x 6mm angle iron with minimum 300mm long ""legs"":" Feeder Pillar 1 Incomer: 1nos 63A TPN MCB 2 set of three phase indicating lamps with suitable protection. "Busbar: Equally sized three phase and neutral copper conductors busbar suitably sized to carry 100A current and suitably insulated with colour coded Heat Shrink Sleeve." Outgoings: 2nos 25A TP Contactor each with set of 6nos 10A SPN MCBs 2nos 24 Hour Timer with auxiliary contacts to close above contactor. 4nos 10A TP MCB (NSR)

Supply of 4 Meter height Carley Square 40W LED in Extruded aluminium bottom pipe (grade 6063 with test certificate) Sq. 150 x 3mm thickness, extruded aluminium stem with inner ribbed Sq.30 x 2mm thickness, extruded aluminium top pipe with inner ribbed with Light Distribution 360°. Pre treated with silicone gaskets. PDC aluminium service door 330mm height x 75mm width at 335mm height above the base plate shall be provided with the company logo embossed on the bottom of the door and safety rope. The control gear tray is prewired with 2.5 Sq.mm cable, 6A MCB and 32A terminal connectors for loop-in / loop-out arrangement. For better lighting performance there is Optical grade clear toughened glass diffuser of 4mm thickness with controlled downward light emission. Lamp fixed is position. This luminaire contains built-in LED modules. LED modules are engineered accordingly to the existing regulations of Lumen Maintenance (LM80) and Technical Memorandum (TM21), Lifespan of the luminaire > 60,000 hours at 40°C. Operating ambient temperature range is from -15°C to +50°C. Driver efficiency >87%, power factor >0.95, IP65, THD <10%, Surge protection 5KV. LED Colour Temperature 3000K, 230-240Vac, CRI >80, MacAdam step> 3, Mechanical resistance IK08. MS mounting plate Sq. 250 x 12mm thick steel of grade E250 to IS 2062:2011 with 4 elongated holes 38 x 19 to suit M16 bolts at CC180. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed foundation pole. Hot dip galvanised foundation bolt. The pole should undergone Pure polyester powder coated process, Mild shot blasting. The product should be BIS and CE Certified. (NSR)

Supply and Fixing of K-Lite Inground Footlight One-sided of 9w (NSR)

Supply, Installation, Test in gand Commissioning of LEDRGB/RGBW flood lighting luminaire for facade lighting with Die- cast aluminium housing, powder- coated finish, of following wattage. Luminaire shall be capable of producing dynamic color changing light for with 16 million colors by DMX/ Ethernet based control. The be amangle of the fitting shall be narrow, medium, wide or asymmetric as per the requirement. Luminaire shall be complete with driver and capable of operating at line voltage without any separate power supply from 100-270 VAC, 50Hz with power factor>0.9. Fixture shall be suitable to operate at anambient temperature range of-10°Cto +50° C and shall be IP65 and IK06 rated. Life time shall be atleast L70:50000 burning hours at 50°C. Luminaire shall be conforming to BIS(IS10322) and shall be complete with all necessary accessories required for proper working of fixture in cluding weatherproof connection cables, waterproof connector setc. as required. 30 W (NSR)

Supply of Surface mounted spot light LED 3000K/4000K/5700K 240Vac CRI >80 MacAdam step 3 Input power : 10W Dimension Ø95 x 124 mm, Beam Angle : 40° without Electronic driver ON/OFF, LUMINAIRE TYPE : Wall Mounted luminaire. IP rating IP66. MATERIAL CHARACTERISTICS: Die-Cast aluminium housing & Front ring (grade ADC12 with test certificate). Surface mounting Bracket made of Polypropylene black. Silicone clear gasket. SS fasteners. Mechanical resistance IK06. Pure polyester powder coated process : Acid treatment & pure polyester powder coating. LIGHTING PERFORMANCE: Toughened Clear glass diffuser of 4mm thickness. This luminaire contains built-in LED modules. LED modules are engineered accordingly to the existing regulations of Lumen Maintenance (LM80) and Technical Memorandum (TM21), Lifespan of the luminaire > 60,000 hours at 40ｰC. Operating ambient temperature range is from -15ｰC to +50ｰC. Driver efficiency >84%, power factor >0.95, THD <15%, Surge protection 2.5KV. (NSR)

Supply & fixing of recess mounting round 15-18 Watts Spot Light (Black Body) LED Round Surface Light, Cylindrical Shape Indoor Ceiling Mounted Spot Light Down Light Aluminium Body in white/black finish complete in all respect. (NSR)

Supply and fixing of 3X18Watts Spot Light (Black Body) LED Round Surface Light, Cylindrical Shape Indoor Ceiling Mounted Spot Light Down Light Aluminium Body in white/black finish complete in all respect. complete in all respect (NSR)

Supply and fixing of Cove Light with complete support and acceNSRies. (NSR)

Please Enable Macros to View BoQ information