THIRD EYE - SUPPLY AND INSTALLATION OF CCTV SURVEILLANCE SYSTEM AND DISPLAY PANEL AT VARIOUS PLACES IN TALIPARAMBA LEGISLATIVE ASSEMBLY CONSTITUENCY IN KANNUR DISTRICT. (2nd PHASE ) UNDER MLASDF 2019-2020

Amount

PART A

Fabrication, erection and commissioning of three legged Narrow Base Tower with square base of 1.0 m2 & square top of 0.35 m2 sides. The tower shall be Three legged and able to support microwave Dish antennae and should be tapered throughout with base width and top width as specified. Height of the tower : 10 mtrs, Bottom base foundation :0.6mtrs X 0.6mtrs X 0.6mtrs, Top side- 0.3048mtrX 0.3048mtrX 0.3048mtr with GI B class pipe, Foundation of the tower concreting : 1.0mtr qr , The type of Foundation of the tower has been designed as per IS standard & safe bearing capacity as 75 KN/m2 (min) should be taken care of when it is subjected soil/concrete test.The erection of tower foundation with concrete proportion of 1:3:6 & M20 concrete shall be used for reinforcement, Control of concrete shall be as per IS 456 : 2000, If needed Non-galvanizing steel structures such as Anchor Nuts,bolts etc. should be painted with red oxide coating. Tower shall be operational and able to withstand the wind velocity corresponding to wind zone 47 m/s as per standard , Note: Concrete and deformed steel bars for foundation are in the scope of tower manufacture or supplier.

Erection and commissioning of GI Tubular Pole with bracket having Standard cable duct , Height- 6 mtr(1mtr below the ground), Equipment Surface Area: 0.25m2 and should be able to withstand equipment weight at top of about 25kg.

Supply, conveyance and installation of 100 Watt Solar panels, Output Power : 100 Watts, Panel Technology : Poly Crystalline, Cell Conversion efficiency : >16% , Compliance to IEC standards, Space Requirement of cell : Standard, Short Circuit Current : Isc (A) 5.92, Number of Cells: 36 or above and should be able to drive 100Ah battery,)

Supply, conveyance and installation of Solar panels frame suitable for 100 Wattt panel and that can be mounted on a various towers with wind Survivability of atleast 200 km/h . MS painted angles may be used for fabrication

Supply, conveyance and installation of Low internal resistance lithium iron battery , Capacity : 100 AH, Nominal Voltage: 12.8V-Storage Temperature: -13~149°F/ -25~65°C, Connection Method: Parallel-Cycle Life: ≥4000 Cycles @ 80% DoD, Dimensions: Approximately 11 inch x 7 inch x 7 inch, Weight: About 12 kg, Certifications: UN38.3, MSDS, UL1642 (Lithium Cell)

Supply, conveyance and installation of Weather-proof Boxes (racks suitable to place battery & MTTP accessories), Painted MS angle iron rack with Standard Zinc galvanized sheet should be used to make the specified rack with accessories such as DC Distribution box, cooling fan and hardware mounting kit.

Supply and installation of 2 port POE Power Injector (12V-12w, 24v-12w, 24V-24w,12V-24w), Power Supply 24V, 0.5A, Gigabit PoE Max. Power Consumption : 5.5W, Power Method : Passive PoE, Supported Voltage Range 12-24VDC suitable for connecting IP cameras

Supply and installation of Main DC Power supply (output-5V, 12V, 24V/ 10amp) (input-10V to 18V)

Supply and installation of suitable Power cord/ adapter for connecting cameras to the power supply

Supply and installation of Solar charger /Power Adapter, 12V/24V, Auto PWM, 10A Solar Charge Controller .Preferred make : Exide or Equivalent .

Supply, conveyance and installation of Lightning arrestor, insulators, GI strip, and star earthing etc, Housing Type- Porcelain, Arrester Length- 3 mtr , Arrester Diameter- 50mm, Class A, Arrester Type- Intermediate Type, Sturdy design, Anti-corrosive for earthing of the tower, 50x3 mm GI strips should be bonded to the all four tower legs at the termination of the base leg of first joint and connected to ring earth at the other end ( The maximum value of earth resistance shall be minimum fraction of ohm.)

Supply and providing ISI plate earthing as per IS 3043 with 600 X 600 X 6.3 mm CI/GI earth plate with required length of 20 mm dia ‘B’ class GI watering pipe, providing GI funnel with weld wash, filling charcoal around the earth plate up to a distance of 15 cm, filling the rest of the portion with excavated soil, including watering and ramming, providing brick work (20 mm) necessary at the top in 1:6 cement mortar, providing cast iron gully trap with GI covering at the top.

Supply, conveyance and installation of Exhauster fan fitted to the weather proof box. Material: Plastic, Blade Material: PP (Poly Propylene), Noise level : Minimal operational sound ,Power rating : less than or equal to 35 W, Speed (RPM): 1350,Operating Voltage: 12 V DC, Sweep size : 200mm

Supply and laying of CAT 6 Cable for interconnecting various equipments including camera and NVR.

Supply and fixing the following sizes of PVC conduit 20 mm ,conforming to IS 9537 / 1983 along with all required accessories

Supply and fixing the following sizes of light gauge, ivory coloured PVC of 20 mm dia light gauge ivory coloured ,conforming to IS 9537 / 1983 part III along with all required accessories

Supply, Installation, Testing and Commissioning of Power beam Antenna, Model : Mm5 400 , Dimensions 325 x 325 x 256 mm (12.8 x 12.8 x 10.1", Operating Frequency 5150 - 5875 MHz, Support Software OS: Ubiquiti firmware technology, Protocol Support : Outdoor multi -point networking ,Features : Ubiquiti Channelization , Spectral Width Adjustment , ACK Auto-Timing , AAP Technology , Multi-Language Support, Throughput 150+ Mbps, Network Interface 10/100/1000, Frequency Band: > 5 GHz ,Antenna Gain > 18 dBi, Power Supply 24V- 0.5A ,Gigabit PoE Max. Power Consumption: 8.5W ,Operating Frequency : U-NII-3 5150 - 5875 MHz ,) Wind Survivability: 200 km/h ,Wireless Approvals: FCC, IC, CE RoHS Compliance ,Vibration Test: IEC 68-2-6, Temperature Shock Test : IEC 68-2-14 UV Test. Preferred make : Ubiquiti

Testing and synchronization of existing Open WRT and Customized software for control of Star topology (TXD/RXD bus signal), track the network status, Control the tampering intrrupt and monitoring channels etc , Enable tower securities and Power analysis by using Tele Camera & Proxy sensors, with help of user interface firmware/DIP package .

Supply, Installation, Testing and Commissioning of HD WDR Net work IR Bullet Cameras having following minimum specifications : 1/2” image sensor ,Lens 2.8"12mm, 4 Megapixel progressive Scan CMOS, H.264+ & H.265 ,25fps@4MP, Day/Night(ICR), Multiple network monitoring: Web viewer, CMS(PVMS), Recommended Make : UNV, Hikvision, Panasonic or equivalent .

Supply and installation of 32" smart TV, Cabling, HDD, Ceiling Mount / wall Mount etc has to be factored , Should have local service centre and Tech support center in Kerala. Should have the R&D support in India, 3 yearwaaranty Preferred make : LG/Sony, Samsung.

Integration of Public Addressing System to the Network with speakers, micro computers ane necessary software

Supply, Installation, Testing and Commissioning of IP Net work Video Recorder & Drive Software with all accessery unit. Features-16channel, Video compression H.264/265 , Up to 10TB HDD Supporting , Max input/record 200mbps , HDMI and VGA Port facilities, Recording Resolution 8MP, Certifications : FCC, CE. Recommended :UNV/Hikvision

Supply, installation, testing and commissioning of 4TB SATA Surveillance HDD 7200 rpm for recording and backing up the camera output to the NVR, which is placed anywhere in the network, 6Gb/s . Recommended: Seagte

Network integration charges for establishing fibre connectivity using 4 PORT Manageable GPON Optical Network Unit

Supply and installation of 4 port Gigabit Network switch with adapter , 8 Gbps forwarding capacity , 8K MAC Address Table, store and forward transmission method, 10 BASE T/100BASE T/1000BASE- T interface options , rack mountable, conforming to FCC class. Recommended: Cisco/Netgear.

Network configuration charges for creating VLANS, assigning IP to various components, providing authorisations and other network management activities

Leasing charge for Fiber Line (for three years)

Supply and fixing 4U Rack for switches and other equuipments with PDU, cooling fan and hardware mounting kit. Recommended: VAL Rack or equivalent.

L.S provision for miscellaneous connecting accessories (BNC, DC & RMC Pin Connectors/ RJ45 connectors and crimping - BESTNET, Anchor bolts& Nuts, Paint to spray tower leggs,Single module PVC/ wooden box with plate for placing camera , screws & Fischer’s, Cable tie & insulation tapes , Flexible pipe, Power cable, power sockets , Power switches whereever necessary, Rack bolts of weather proof boxes and inegration of softwares on LAN (VC and PA systems) etc., providing project boards, route marker as per the requirements including all other charges.

Fabrication, Erection and Commissioning of Three legged Narrow Base Tower with square base of 1.5 m2 & square top of 0.35 m2 sides. The tower shall be Three legged and able to support microwave Dish antennae and it is tapered throughout with base width and top width as specified in , Height of the tower : 24 mtrs, Bottom/Top Structural base foundation : 1m2 /0.35m2 with GI- B class pipe, Foundation of the tower concreting : 1.5 mtr qr , The type of Foundation of the tower has been designed as per IS standard & safe bearing capacity as 75 KN/m2 (min) should be taken care of when it is subjected soil /Concrete test. The erection of tower foundation with concrete proportion of 1:3:6 & M20 concrete stone shall be used for reinforcement, Control of concrete shall be as per IS 456 : 2000, If needed Non-galvanizing steel structures such as Anchor Nuts,bolts etc. should be painted with red oxide coating. Tower shall be operational and able to withstand the wind velocity corresponding to wind zone 47 m/s as per standard , Note: Concrete and deformed steel bars for foundation are in the scope of tower manufacture or supplier.

Fabrication, Erection and Commissioning of Three legged Narrow Base Tower with square base of 1.2 m2 & square top of 0.28 m2 sides. The tower shall be Three legged and able to support microwave Dish antennae and it is tapered throughout with base width and top width as specified in , Height of the tower : 18 mtrs, Bottom/Top Structural base foundation : 1m2 /0.28m2 with GI- B class pipe, Foundation of the tower concreting : 1.2 mtr qr , The type of Foundation of the tower has been designed as per IS standard & safe bearing capacity as 75 KN/m2 (min) should be taken care of when it is subjected soil /Concrete test. The erection of tower foundation with concrete proportion of 1:3:6 & M20 concrete stone shall be used for reinforcement, Control of concrete shall be as per IS 456 : 2000, If needed Non-galvanizing steel structures such as Anchor Nuts,bolts etc. should be painted with red oxide coating. The earth base plates should be galvanized as major portion of them may be directly undergo, Tower shall be operational and able to withstand the wind velocity corresponding to wind zone 47 m/s as per standard , Note: Concrete and deformed steel bars for foundation are in the scope of tower manufacture or supplier.

Fabrication, Erection and Commissioning of Three legged Narrow Base Tower with square base of 1 m2 & square top of 0.20 m2 sides. The tower shall be Three legged and able to support microwave Dish antennae and it is tapered throughout with base width and top width as specified in , Height of the tower : 12 mtrs, Bottom/Top Structural base foundation : 1m2 /0.20m2 with GI- B class pipe, Foundation of the tower concreting : 1.2 mtr qr , The type of Foundation of the tower has been designed as per IS standard & safe bearing capacity as 75 KN/m2 (min) should be taken care of when it is subjected soil /Concrete test. The erection of tower foundation with concrete proportion of 1:3:6 & M20 concrete stone shall be used for reinforcement, Control of concrete shall be as per IS 456 : 2000, If needed Non-galvanizing steel structures such as Anchor Nuts,bolts etc. should be painted with red oxide coating. The earth base plates should be galvanized as major portion of them may be directly undergo, Tower shall be operational and able to withstand the wind velocity corresponding to wind zone 47 m/s as per standard , Note: Concrete and deformed steel bars for foundation are in the scope of tower manufacture or supplier.

Supply and Installation of 6M , 6" GI Pole corrosion resistant for Mounting Cameras accessories including all necessary civil works of base should be .50mX.50mX.50mX.50m, such as digging, concreate, painting etc

Supply and installation of Aviation warning lamps/ Pilot Lamps with switcing circuit for 24mtr tower, Input voltage : 12V,Watts : Less than or equal 5W, Type : LED switcing , Durability : Long last .

Supply, conveyance and installation of 100 Watt Solar panels, Output Power : 100 Watts, Panel Technology : Poly Crystalline, Cell Conversion efficiency : >16% , Compliance to IEC standards, Space Requirement of cell : Standard, Short Circuit Current : Isc (A) 5.92, Number of Cells: 36 or above and should be able to drive 100Ah battery,)

Supply, conveyance and installation of Solar panels frame suitable for 100 Wattt panel and that can be mounted on a various towers with wind Survivability of atleast 200 km/h . MS painted angles may be used for fabrication

Supply, conveyance and installation of Low internal resistance lithium iron battery , Capacity : 100 AH, Nominal Voltage: 12.8V-Storage Temperature: -13~149°F/ -25~65°C, Connection Method: Parallel-Cycle Life: ≥4000 Cycles @ 80% DoD, Dimensions: Approximately 11 inch x 7 inch x 7 inch, Weight: About 12 kg, Certifications: UN38.3, MSDS, UL1642 (Lithium Cell)

Supply, conveyance and installation of weather proof Boxes (racks suitable to place battery & MTTP accessories for the said project), Painted MS angle iron rack with Standard Zinc galvanized sheet should be used to make the specified rack. DC Distribution box, cooling fan and hardware mounting kit etc needs to be provided. It should be capable of bearing wind speed of 60km/h

Supply and installation of 8 port POE Power Injector (12V-12w, 24v-12w, 24V-24w,12V-24w), Power Supply 24V, 0.5A, Gigabit PoE Max. Power Consumption : 5.5W, Power Method : Passive PoE, Supported Voltage Range 12-24VDC, Operating Frequency : Worldwide Recommended.

Supply and installation of dual port POE Power Injector (12V-12w, 24v-12w, 24V-24w,12V-24w), Power Supply 24V, 0.5A, Gigabit PoE Max. Power Consumption : 5.5W, Power Method : Passive PoE, Supported Voltage Range 12-24VDC.

Supply and installation of Main DC Power supply (output-5V, 12V, 24V/ 10amp) (input-10V to 18V)

Supply and installation of suitable Power cord/ adapter for connecting cameras to the power supply

Supply and installation of Solar charger /Power Adapter, 12V/24V, Auto PWM, 10A Solar Charge Controller . Preferred make : Exide or Equivalent .

Supply, conveyance and installation of Lightning arrestor, insulators, GI strip, and star earthing etc, Housing Type- Porcelain, Arrester Length- 3 mtr, Arrester Diameter- 50mm, Class A, Arrester Type- Intermediate Type, Sturdy design, Anti-corrosive for earthing of the tower, 50x3 mm GI strips should be bonded to the all four tower legs at the termination of the base leg of first joint and connected to ring earth at the other end ( The maximum value of earth resistance shall be minimum fraction of ohm.)

Supply, conveyance and installation of Exhauster fan, Material:Plastic, Blade Material: PP (Poly Propylene), Noise level : Minimal operational sound ,Power rating: less than or equal to 35 W, Speed (RPM: 1350,Operating Voltage: 12 DC, Sweep size: 200mm,The size shall be specified based on the farication of racks.

Supply and laying of CAT 6 UTP Cable for interconnecting camera and accessories laying, power supply and giving connection using standard graded connectors.

Supply and laying of CAT 6 FTP Cable for interconnecting camera and accessories laying, power supply and giving connection using standard graded connectors.

Supply and fixing the 20 mm dia light gauge ivory coloured PVC conduit conforming to IS 9537 / 1983 part III along with all required accessories as required.

Supply, Installation, Testing and Commissioning of Power beam Antenna, Model : Mm5 400 , Dimensions 325 x 325 x 256 mm (12.8 x 12.8 x 10.1", Operating Frequency 5150 - 5875 MHz, Support Software OS: Ubiquiti firmware technology, Protocol Support : Outdoor multi -point networking ,Features : Ubiquiti Channelization , Spectral Width Adjustment , ACK Auto-Timing , AAP Technology , Multi-Language Support, Throughput 150+ Mbps, Network Interface 10/100/1000, Frequency Band: > 5 GHz ,Antenna Gain > 18 dBi, Power Supply 24V- 0.5A ,Gigabit PoE Max. Power Consumption: 8.5W ,Operating Frequency : U-NII-3 5150 - 5875 MHz ,) Wind Survivability: 200 km/h ,Wireless Approvals: FCC, IC, CE RoHS Compliance ,Vibration Test: IEC 68-2-6, Temperature Shock Test : IEC 68-2-14 UV Test. Preferred make : Ubiquiti

Supply, Installation, Testing and Commissioning of Open WRT and Customized software for control of Star topology (TXD/RXD bus signal), track the network status, Control the tampering intrrupt and monitoring channels etc , Enable tower securities and Power analysis by using Tele Camera & Proxy sensors, with help of user interface firmware /DIP package.

Supply, Installation, Testing and Commissioning of HD WDR Net work IR Bullet Cameras having following minimum specifications : 1/3” image sensor, 4 Megapixel progressive Scan CMOS , 2.8-12mm Motrorized lens, Micro SD Card 128GB, H.264+ & H.265 dual-stream encoding, 25/30fps@3M(2304×1296), Max IR LEDs Length 50m, IP67, PoE ,DWDR, Day/Night(ICR), 3DNR, AWB, AGC, ROI,BLC,HLC, Multiple network monitoring: Web viewer, CMS(PVMS) Prefered Make : UNV, Panasonic, Hikvision / equivalaent

Supply, Installation, Testing and Commissioning of IP Net work Video Recorder & Drive Software with all auxillary unit. Features-8-16 channel, Video compression H.264 MJPEG , 8TB HDD Supporting , PoE supporting, Max input/record 200mbps , USB, LAN and VGA Port facilities as well, Resolution 5Mp(2560×1920) / 4Mp(2560×1440) , Certifications : FCC, CE , UL and ONVIF-S year 2017, including giving connection devices and all other charges. Recommended :Bosch/Panasonic.(preferred model Panasonic UNV, Hikvision or equivalent )

Supply, installation, testing and commissioning of 4TB SATA HDD 7200 rpm for recording and backing up the camera output to the dedicated Server/ NVR, which is placed anywhere in the District.

Supply, Installation ( wall mount), Testing and Commissioning of 50” Monitor with Full HD , 1920 x 1080 panel resolution optimized for CCTV applications and designed for 24/7 use. : 60Hz Slim D-LED BLU panel technology , excellent picture quality, 8ms response time, Landscape / Portrait, video output via HDMI, contrast ratio : 5000:1, Brightness :350 nits, VGA and composite, the SMT-4030 is the perfect professional security monitor. professional LED Display including all Accessories. (Recommended: Samsung/Sony/LG )

Supply, Installation ( wall mount), Testing and Commissioning of 28” Monitor with Full HD , 1920 x 1080 panel resolution optimized for CCTV applications and designed for 24/7 use. : 60Hz Slim D-LED BLU panel technology , excellent picture quality, 8ms response time, Landscape / Portrait, video output via HDMI, contrast ratio : 5000:1, Brightness :350 nits, VGA and composite, professional LED Display including all Accessories. 3 years onsite warranty. (Recommended: Samsung/Sony/LG )

Supply and installation of 8 port Gigabit SWITCH with Adapter , 32 Gbps forwarding capacity , 8K MAC Address Table, store and forward transmission method, 10 BASE T/100BASE T/1000BASE- T interface options conforming to FCC class. Recommended: Cisco/Netgear.

Supply and fixing 6U Rack for switches, Patch panels and accessories with cable manager, AC Distribution box, cooling fan and hardware mounting kit Recommended: VAL Rack or equivalent.

Supply 700VA offline UPS with 2 x 12 Volt 7 Ah battery

Supply and installation of BIS Certified 2MP or higher, IP Bullet Camera with 1/2.9" Progressive scan sensor, 30m or above IR Range, Fixed Lens, 1920x1080, 1-25(30) fps and 1280x720, 1-25 (30) fps main stream video ouptut, H264/H265 codec decoding, Low bitrate control, inbuilt PoE support, IP66 weather proof protection Metal body. (Make: Panasonic/CP Plus/UNV or equivalent)

L.S provision for miscellaneous connecting accessories (BNC, DC & RMC Pin Connectors/ RJ45 connectors and crimping - BESTNET, Anchor bolts& Nuts, Paint to spray tower leggs,Single module PVC/ wooden box with plate for placing camera , screws & Fischer’s, Cable tie & insulation tapes , Flexible pipe, Power cable, power sockets , Power switches whereever necessary, Rack bolts of weather proof boxes and inegration of softwares on LAN (VC and PA systems) etc., providing project boards, route marker as per the requirements including all other charges.

EMAC Automation Solutions (I) Pvt Ltd