Civil Work

No. Figure Amount

Civil works items

1 Excavation for foundation upto 1.50 mt depth including sorting out and stacking 104.56 Cum 268.28

of useful materials and disposing the excavated stuff for all lead and lift for all

sorts of soil.

2 Excavation for foundation from 1.50 mt to 3.00 mt. depth including sorting out 32.44 Cum 289.92

and stacking of useful materials and disposing the excavated stuff with all lead

and lift for all sorts of soil.

3 Providing and laying cement concrete work 1:2:4 (1- Cement : 2- Coarse sand : 9.07 Cum 4188.47

4 graded stone aggregates 20 mm nominal size) and curing complete

excluding cost of formwork and reinforcement for reinforced concrete work in

(A) Foundations, footings, base or columns and mass concrete. (For PCC)

4 Providing and laying controlled cement concrete M-250 and finishing smooth 15.58 Cum 4906.58

with curing etc complete, including the cost of formwork but excluding the cost

of reinforcement for R.C.C. work in Foundations, footings base of columns &

mass concrete. (For Footing)

5 Providing and laying controlled cement concrete M-250 and curing complete 6.08 Cum 7742.66

including the cost of form work but excluding the cost of reinforcement for

reinforced concrete work in Columns, pillars, posts & struts upto floor two level

for G.F. (For Column Up to PL)

6 Providing and laying controlled cement concrete M-250 and curing complete 13.41 Cum 5875.17

including the cost of form work but excluding the cost of reinforcement for

reinforced concrete work in (C) Slabs, landing, shelves, Balconies, Lintels,

Beams, Girders and Cantilever upto floor two level. (For Ground Beam)

7 Filling available excavated earth (excluding rock) in trenches plinth side of 96.10 Cum 133.65

foundation etc. in layer not exceeding 20 cm in depth consolidation each

deposited layer by ramming and watering etc. complete.

thickness including watering, ramming and consolidating etc. complete.

9 Filling in plinth with sand under floors including watering, ramming, 5.68 Cum 471.69

consolidating and dressing complete.

10 Anti-Termite System : Providing and laying of permanent piping technology anti- 113.63 Sq.m. 134.33

termite treatment before flooring work by installing LLDP (Low linear density

polyethylene) tube of 8 mm O.D. & 6.4 mm 1.D. with inbuilt pressure

compensation chip every 30 cm interval in the tube, having working pressure of

2 Kg/cm2 and release rate of 1.9 Itr/hour fixed by P-clips and nails. The LLDP

pipe shall be installed at the entire periphery of the building and at internal

network of building at a depth of 20 to 200 mm under floor at every 2 to 3 mtr.

c/c distance (adjusted as per building layout) & ends of loop pass through a

PVC elbow of minimum 32 mm ID at junction box of wall and floor level,

entering into a steel reinforced grooved flexible pipe of minimum 22 mm ID

leading into junction box and the loops shall terminate in junction boxes & test

every junction during injecting chemicals for termite control treatment.

The anti termite chemical Imidacloprid 30.5% SC mix as per IS-6313 (part III)

shall be injected by the pressure pump diluted with water @ 10.5 ml/5 ltr of

water at the rate of 2 Kg/sq.cm @ 5 Ltr/SMT. The contractor shall submit

approved line plan for piping system and junction boxes dully approved by

Engineer-in-Charge with bond of 5 year warranty. (i) Permanent pipe system

with junction boxes (Only pipe network)

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

11 Providing and laying damp proof course 25mm thick cement concrete 1:2:4 (1- 22.84 Sq.m. 304.53

Cement : 2 coarse sand : 4 stone aggregate 10 mm nominal size) and curing

12 Providing and laying brick work using common burnt clay building 15.62 Cum 4121.55

conventional type bricks having crushing strength not less than 35 Kg./Sq.cm.

in foundation and plinth in cement mortar 1:6 (1 cement : 6 fine sand)

including the cost of all materials and labour charges etc. complete. (For B/w

Up to Plinth)

13 Providing and laying brick work using common burnt clay building conventional 31.84 Cum 4396.56

type bricks having crushing strength not less than 35 Kg/sq.cm. in super

structure above floor two level in cement mortar 1:6 (1 cement : 6 fine sand)

including the cost of all materials and labour charges etc. complete. (For B/W

Uo to GF Slab)

14 Providing and laying half brick work using common burnt clay building 101.09 Sq.m. 732.92

conventional type bricks having crushing strength not less than 35 Kg/Sq.cm in

cement mortar 1:3 (1 cement : 3 coarse sand) with 2 Nos. of 6 mm Mild steel

round bars after every three course embedded in cement mortar in foundation

and plinth including the cost of all materials and labour charges etc. complete.

15 Providing and laying cement concrete 1:3:6 (1- Cement : 3- Coarse sand : 6 7.22 Cum 3993.11

crushed stone aggregates 20 mm nominal size) and curing complete including

cost of formwork in (A) Wall Caps / Coping

16 Providing and laying controlled cement concrete M-200 and curing etc. 4.23 Cum 7230.59

complete including the cost of form work but excluding the cost of

reinforcement in (C) Slabs landings shelves balconies, lintel -chhaja, beams,

girders and cantilever up floor to level. (For Lintel)

17 Providing and laying controlled cement concrete M-200 and curing etc. 1.46 Cum 6676.10

complete including the cost of form work but excluding the cost of

reinforcement in (C) Slabs landings shelves balconies, lintel-chhaja, beams,

girders and cantilever up floor to level. (For Chhajja)

18 Providing and laying controlled cement concrete M-200 and curing etc. 6.81 Cum 7677.01

complete including the cost of form work but excluding the cost of

reinforcement in Collumns, pillars, posts & struts upto floor two level for G.F.

(For Column)

19 Providing and laying controlled cement concrete M-200 and curing etc. 13.41 Cum 6336.74

complete including the cost of form work but excluding the cost of

reinforcement in (C) Slabs landings shelves balconies, lintel-chhaja, beams,

girders and cantilever up floor to level. (For beam)

20 Providing and laying controlled cement concrete M-200 and curing etc. 17.05 Cum 4693.47

complete including the cost of form work but excluding the cost of

reinforcement in (C) Slabs landings shelves balconies, lintel-chhaja, beams,

girders and cantilever up floor to level. (For Grade slab)

21 Providing and laying controlled cement concrete M-200 and curing etc. 17.51 Cum 6432.69

complete including the cost of form work but excluding the cost of

reinforcement in (C) Slabs landings shelves balconies, lintel-chhaja, beams,

girders and cantilever up floor to level. (For G.F. slab)

22 Providing I.S.I. Mark T.M.T. bar Fe-500D reinforcement for R.C.C. work 11513.00 Kg. 77.29

including bending, binding and placing in position complete upto all floor level.

23 Providing and fixing M.S. Fan clamps type 1 to 16mm dia M.S. bar bent to 8.00 No. 131.93

shape with hooked ends to R.C.C. slabs curing, laying including painting the

exposed portion of loops, all as per standard design complete

24 Providing & fixing 40 mm thick Single shutter flush door solid core finished with 10.08 Sq.m. 7424.51

both side 1 mm thick lamination both side like 'NOVAPAN 'or equivalent of

natural wood grain shade as approved by this office having telephone black

granite 18 mm thick frame with double stone as per the instruction of Engineer

in charge with necessary SS hinges and fixtures etc. complete.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

25 Providing & fixing 35 mm thick Single shutter flush door solid core finished with 6.30 Sq.m. 7015.46

both side 1 mm thick laminationboth side like 'NOVAPAN 'or equivalent, of

natural wood grain shade as approved by this office having telephone black

granite 18 mm thick frame with double stone including fixed ventilation above

lintel level as per drawing and as per the instruction of Engineer in charge with

necessary SS hinges and fixtures etc. complete.

26 Providing and fixing window having extruded aluminum colour anodized section 18.72 Sq.m. 3199.68

frame main outer size 95mm x 24mm x 1.17mm (@ Wt. 0.738 Kg/mt),

horizontal three track member size 92mm x 31.75mm x 1.30mm (@ Wt.

Kg/mt), vertical member of size 92mm 31.75mm x 1.50mm (@ Wt. 1.06 Kg/mt)

with sliding shutters of horizontal member size 40mm x 18mm x 1.29mm (@

Wt. of 0.456 Kg/mt), vertical member of size 40mm x 18mm x 1.29 mm (@ Wt.

of 0.456 kg / mt) with 5 mm thick transparent bronze colour tinted float glass

with powder coated aluminum fittings and fixtures and transparent silicon

sealant glass fixing including granite frame as per details etc. (Up down Frame)

27 Providing and fixing louvered type ventilators with powder coated aluminum 0.81 Sq.m. 13733.98

fittings and fixtures and Blur glass fixing to adjustable louvers and black granite

frame as per details and executed as per directed by Engineer in charge.

28 Providing and fixing M.S. grills of required pattern to wooden / Marble / Granite 362.09 Kg. 128.27

/ Stone frames of windows etc. with M.S. flats at required spacings and frame

alround, square or round bars with round headed bolts and nuts or by screws

(A) Ornamental Grill.

29 Providing and laying 24" x 24" vitrified 8 mm thick tiles flooring over 20mm 92.47 Sq.m. 1451.16

(average) base of cement mortar 1:6 (1 cement : 6 coarse sand) on new

surface or fixing on existing flooring by adhesive material including dismentaling

of existing flooring and jointed with color cement slurry including finished with

flush pointing & cleaning the surface etc. complete for light shade.

30 Providing and laying 24" x 24" vitrified 8 mm thick tiles flooring over 20mm 11.45 Sq.m. 1432.78

(average) base of cement mortar 1:6 (1 cement : 6 coarse sand) on new

surface or fixing on existing flooring by adhesive material including dismentaling

of existing flooring and jointed with color cement slurry including finished with

flush pointing & cleaning the surface etc. complete for anti skid.

31 Providing and laying Marbo Granite tiles 8 to 10 mm thick, 24'' x 24'' in skirting, 81.21 Sq.m. 1169.98

risers of steps and dedo on 10mm thick cement plaster 1:3 (1 cement :

coarse sand) and jointed with white cement slurry.

32 Providing and laying 18 mm thick machine cut, free edges, machine polished 5.74 Sq.m. 3325.93

Black Granite tread and risers in single piece with 1 cm nosing and necessary

grooves on treads etc. complete.

33 Providing and laying BBCC of 75mm thick layer in CM (1:3) including spraying 122.60 Sq.m. 621.15

i.e. perma or other with leveling complete for ready base of china mosaic

treatment.

34 Providing and laying broken china mosaic flooring for terrace using 12 mm to 111.70 Sq.m. 765.97

20 mm broken pieces of glazed tiles to be laid over cement mortar 1:3 to plain

or slope and to be tempered to bring mortar creme out upto surface using white

cement including rounding off junctions and extending them upto 15 cm along

the wall, clearing with water and oxalic acid etc. as directed.

35 Providing and cement vata (10cm x 10cm size) quarter round in cement mortar 138.86 Rmt. 24.28

1:1 including neat cement finishing watering etc. complete.

36 Providing 15mm thick cement plaster in single coat on rough (similar) side of 231.32 Sq.m. 194.53

single or half brick walls for interior plastering upto floor two level and finished

even and smooth in cement mortar 1:4 (1 cement : 4 sand) including

galvanised iron chicken mesh complete.(Interior Plaster)

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

37 Providing 15mm thick cement plaster in single coat on brick/concrete walls for 131.09 Sq.m. 196.64

interior plastering upto floor two level and finished even and smooth in cement

mortar 1:4 (1-cement : 4 sand) for ceiling.

38 Providing 20mm thick sand faced cement plaster on walls upto height 10 279.39 Sq.m. 345.42

metres above ground level consisting of 12mm thick backing coat of C.M. 1:3

(1-cement : 3-sand) and 8mm thick finishing coat of C.M. 1:1 (1-cement : 1-

sand) etc. complete.

39 Providing throating or plaster drip and moulding to R.C.C. Chhajja. 33.27 Rmt. 42.02

40 Applying two coats of putty & two coats of primer of approved brand and 167.86 Sq.m. 40.59

manufacture on new wall surface to give an even shade including thoroughly

brushing the surface free from mortar dropping and other foreign matter and

sand papered smooth.

41 Applying two coats of putty & two coats of primer of approved brand and 131.09 Sq.m. 42.72

manufacture on new wall surface to give an even shade including thoroughly

brushing the surface free from mortar dropping and other foreign matter and

sand papered smooth. (Ceiling Putty)

42 Wall painting two coats with plastic emulsion paint of approved brand and 167.86 Sq.m. 80.87

manufacture on wall surfaces to give an even shade including throughly

brushing the surface free from mortar droppings and other foreign matter and

sand papered smooth. (Interior Wall Paint)

43 Finishing wall with weather proof exterior emulsion paint on wall surface (two 279.39 Sq.m. 117.40

coats) to give an required shape even shade after thoroughly brushing surface

to remove all dirt, dust and remains of loose powdered materials etc. complete.

(Exterior Wall Paint)

44 Wall painting two coats with plastic emulsion paint of approved brand and 131.09 Sq.m. 83.00

manufacture on wall surfaces to give an even shade including throughly

brushing the surface free from mortar droppings and other foreign matter and

sand papered smooth on ceiling. (Ceiling Paint)

45 Providing, laying and jointing in true line and level I.S.I. mark 40mm dia. 11.00 Rmt. 148.12

U.P.V.C pipe (Sch-40) for cold water including fitting as approved by Engineer

in charge. Pipe shall be fixed on the wall with held of clamp at every two meter

c/c or shall be concealed as directed including necessary fitting etc. including

testing of pipe and joints and fixing the same with adhesive solvent including

cost of all materials.

46 Providing, laying and jointing in true line and level I.S.I. mark 32mm dia. 25.00 Rmt. 119.15

U.P.V.C pipe (Sch-40) for cold water including fitting as approved by Engineer

in charge. Pipe shall be fixed on the wall with held of clamp at every two meter

c/c or shall be concealed as directed including necessary fitting etc. including

testing of pipe and joints and fixing the same with adhesive solvent including

cost of all materials.

47 Providing, laying and jointing in true line and level I.S.I. mark 15mm dia. 26.00 Rmt. 72.65

U.P.V.C pipe (Sch-40) for cold water including fitting as approved by Engineer

in charge. Pipe shall be fixed on the wall with held of clamp at every two meter

c/c or shall be concealed as directed including necessary fitting etc. including

testing of pipe and joints and fixing the same with adhesive solvent including

cost of all materials.

48 Providing and fixing concealed center point to wall, ceiling and floor I.S.I. mark 18.00 Rmt. 660.58

C.P.V.C. (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal

for potable water of following dia. nominal bore tube fittings and clamps

including making good the wall, ceiling and floor etc. complete. (F) 50 mm dia.

49 Providing and fixing concealed center point to wall, ceiling and floor I.S.I. mark 26.00 Rmt. 253.82

C.P.V.C. (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal

for potable water of following dia. nominal bore tube fittings and clamps

including making good the wall, ceiling and floor etc. complete. (B) 25 mm dia.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

50 Providing, laying and jointing in true line and level I.S.I. mark 110mm diameter 31.00 Rmt. 856.03

U.P.V.C. SWR Type B pipe confirming to IS 13592 -1992 with one end plain

and other end socketed with rubbering & fitting confirming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall be jointed with each

other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of

the size 110mm diameter x 149mm length x 145mm high at every 2000mm

center to center or shall be concealed in wall as directed including necessary

fitting such as bends, shoes etc. including testing of pipe and joints and jointed

with adhesive solvent cement including cost of all materials.

51 Providing and fixing screw down bib taps of following size (A) Brass chromium 8.00 No. 186.83

plated screw down bib tap (i) 15mm dia. as approved by Engineer in charge for

all floors.

52 Providing and fixing screw down bib taps of following size (A) Brass screw 3.00 No. 214.81

down bib tap polished bright (ii) 20mm dia. as approved by Engineer in charge

for all floors.

53 Providing and fixing pillar tap, capstan head screw down high pressure with 4.00 No. 354.69

screw, shanks and back nuts (B) 20mm dia. as directed by Engineer in charge.

54 Providing and fixing chromium plated brass half turn flush cock of approved 7.00 No. 263.77

quality including fixing in pipe line etc. complete. (ii) 25mm dia. as directed by

Engineer in charge.

55 Providing and fixing Gun metal check or non return full way wheel valve. 40 3.00 No. 663.43

56 Providing and fixing Gun metal check or non return full way wheel valve. (C) 25 5.00 No. 420.63

57 Providing and fixing Granite of 18 to 20mm thick having minimum single 3.00 No. 9511.17

piece length of 210mm to be fixed on Walls to act as Study Table / Wash

basin, including fixing the same using cement mortar in proportion 1:1 etc.

complete necessary Groove in walls by machine, front side round the edge and

cutting hole in granite stone for wash basin, Computer wire, including rubbing

and polishing finishing jointed with grey cement slurry including rubbing and

polishing finishing etc. complete with all labour & material & equipment etc.

completed as directed by Engineer-in-charge (A) Granite slab 18mm thick

58 Providing and fixing C.P. brass towel rail complete with C.P. brass brackets 3.00 No. 616.42

fixed to wooden plugs with C.P. brass screws.(B) 600 mm x 20 mm size.

59 Providing and fixing C.P. brass shower rose with 15mm or 20mm inlet.(A) 3.00 No. 282.16

100mm dia. each

60 Providing and fixing 600mm x 450mm bevelled edge mirror of superior glass 3.00 No. 854.58

mounted on 6mm thick A.C. sheet or plywood sheet and fixing to wooden plug

with C.P. brass screws and washers.

61 Providing and laying wash down water closet (European type Wall hung W.C. 3.00 No. 10261.60

pan) Florentine series FLS-WHT 0111B including providing and fixing

metropole flush cock seat cover, jet wash etc. complete unit of jaquar branch

(or equivalent) including installing and fitting as per manufacturers standards by

skilled trained plumber including testing etc. complete quality and brand as

approved by Engineer in charge.

62 Providing, laying and jointing in true line and level I.S.I. mark 160mm diameter 48.00 Rmt. 834.38

U.P.V.C. (Type B) confirming to IS 13592 -1992 with one end plain and other

end socketed with rubbering & fitting confirming to ISI 14735-1999 of approved

make for drainage system pipe line, pipe shall be jointed with each other with

rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size

160mm diameter x 210mm length x 196mm high at every 2000mm center to

center or shall be concealed in wall as directed including necessary fitting such

as bends, shoes etc. including testing of pipe and joints and jointed with

adhesive solvent cement including cost of all materials.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

63 Providing and fixing PVC SWR Nahni Trap IS 14735 for drain with jail of the 8.00 No. 572.32

following nominal diameter of self cleansing design with C.I. screwed down of

hinged grating including the cost of cutting and making good the walls. (i)

100mm dia.

64 Providing and laying (two level or slopes) and jointing with stiff mixture of 21.00 Rmt. 312.76

cement mortar in proportion 1:1 salt glazed stone ware pipes following nominal

internal diametre including testing of pipes and joints etc. complete. 150 mm

65 Constructing brick masonary chamber for under ground C.I. Inspection 2.00 No. 2932.93

chamber and bends with bricks having crushing strength not less than

Kg/cm2 in C.M. 1:5 C.I. cover with frame (light duty) 455 mm x 610 mm.

internal dimensions, total weight of cover with frame to be not less than 38 Kgs.

weight of cover 23 Kg. and wt. of frame 15 Kg) R.C.C. top slab with 1:2:4 mix

(1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm. size) foundation

concrete 1:5:10 inside plaster 15 mm. thick with cement mortar 1:3 finished

smooth with a floating coat of neat cement on walls & a bed concrete etc.

complete. (i) inside dimension 455mm x 610 mm and 450mm deep for single

pipe line.

66 Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement :2-coarse 1.00 No. 11042.74

sand : 4-graded stone aggregate 20mm nominal size) foundation concrete

1:3:6 mix (1-cement : 3- coarse sand :6-Brick bats 40 + 50mm size) inside

plastering 15mm thick with Cement Mortar 1:5 (1-Cement : 5-coarse sand)

finished with a floating coat of neat cement and making channels in cement

concrete 1:2:4 mix (1-Cement : 2-Coarse sand :4-stone aggregate 20mm

nominal size) finished smooth complete including curing and festing (i) Inside

size 900mm x 1200mm and 1.5M. deep including C.I. cover with frame size

560mm diameter total weight of cover and frame to be not less than 128 kgs.

(Wt. of cover 64 Kg. and Wt. of frame 64 Kg.) (A) With 230mm thick walls of

brick masonry using brick having crushing strength not less than 35Kg. /

Sq.cm. in Cement Mortar 1:5 (1- Cement : 5 Coarse sand) (1) A type depth

0.90 Metre for 150mm diameter sewer.

67 Providing erecting and fixing double coated Syntex or equivalent PVC (I.S.I.) 2000.00 Litre 3.95

mark water tank of required capacity each with all necessary fittings &

connection etc. comp on terrace.

68 Providing and fixing ball cock of approved quality as directed. (A) Copper metal 1.00 No. 132.89

(i) 25 mm dia.

69 Supply and fixing the SS letter finish with chromium and height is not less 25.00 No. 1378.65

than 10". SS made of 304 and surface should be reflective type (including all

labour, material, fixing, transportation and CNC cutting) and Item should be

executed as per directed by Engineer in charge.

70 Providing and laying sandwich type kitchen platform of size 2.10 x 0.76 x 0.76 1.50 Rmt. 23691.57

m and respected length with dhar polish or moulding having base 4" and

support & base with marble or kota as per site requirement also loft and base

pipe provision and sink including all fittings, material and labour as per directed

by Engineer incharge.

71 Clearing and grubbing road land including uprooting rank vegetation grass 0.03 Hect. 82249.89

bushes, shrubs, sapling and trees girth up to 300 mm removal of stumps of

trees cut earlier and disposal of unserviceable materials (A) By manual means

in area of light jungle.

72 Providing & fixing Co2 type portable ABC Dry Powder type ABS Fire 5.00 No. 3535.00

extinguisher capacity 4.5 Kg. discharge range 3mt. timing 60 to 180 sec.

standard approved IS code No. 2878:2004.

73 Providing sock pit of 5.00 Cu.M. Volume including excavating and filling brick 1.00 No. 3427.65

bats with dry masonry work at top for 45cm. height including covering the top

with stone including providing vatas in C.M. 1:3 with finishing curing etc.

complete as directed.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

74 Providing and fixing fabricated Ladder including Stringer, stairbase, made 1.00 No. 8787.00

using various member of mild steel like hollow box section 75 x 50 x 3mm for

Stringer, 50 x 50 x 3 for Step, MS plate and Pedestal CC block (350 x 350 x

500mm) and other as per design inculding all hardware, fixture, welding, cutting

having minimum weight of 160 kg and assembale with two coat of red oxide

primer and two coat of paint complete as per directed by engineer in charge.

75 Providing and fixing eco-friendly light weight calcium silicate false ceiling tiles 27.16 Sq.m. 1674.15

having Tegular edge & 15 mm thick densified edges on the Tile Periphery for

extra strength. The light weight calcium silicate ceiling tiles shall have , light

reflection 85% non-combustible as per B.S. 476 part IV, 100% humidity

resistance and also having thermal conductivity0.043° w/m KC.for the best

thermal Insulation. The Light weight calcium Silicate tile shall be of approved

texture Fine fissured/ Spintone/Cosmos having NRC value of 0.5 & globe

having NRC value of 0.75 NRC or equivalent of size 595 x 595 mm to be laid

on true horizontal level suspended inter locking metal grid of hot dipped

galvanized steel sections (galvanizing @120 grams per sqm including both

side) consisting of main ‘T’ runner suitably spaced at joints to get required

length and size of 24 x 38mm made from 0.30 mm thick (minimum) sheet,

1200mm centre to centre and cross ‘T’ of size 24 x 28mm made out of 0.33mm

(Minimum) sheet spaced 1200mm along spaced between main ‘T’ at 600mm

centre to centre to form a grid of 1200 x 600mm and secondary

cross ’T’ of length 600mm and size 24 x 28mm made of 0.30 mm thick

(Minimum) sheet to be interlocked at middle of the 1200 x 600mm panel to

form grid of size 600 x 600mm resting on periphery walls/partitions on a

perimeter wall angle pre-coated steel of size (24 x 24 x 3000mm made of

0.40mm thick (minimum) sheet with the help of rawl plugs at 450mm centre to

centre with 25mm long dry wall screws @ 230mm interval and laying 15mm

thick Densified edges light weight calcium silicate ceiling tiles of approved

texture (Fine Fissured / Cosmos / Spintone) in the grid including cutting /

making opening for services like diffusers, grills, light fittings, fixtures, smoke

detectors etc., wherever required, Main ‘T’ runners to be suspended from

ceiling using G.I. slotted cleats of size 25 x 35 x 1.6mm fixed to ceiling with

12.5mm dia and 50mm long dash fasteners, 4mm G.I. adjustable rods with

galvanized steel level clips of size 85 x 30 x 0.8mm, spaced at 1200mm centre

to centre long main ‘T’ bottom exposed with 24mm of all T-sections shall be

pre-painted with polyester baked paint, for all heights, as per specifications,

drawings and as directed by engineer-in-charge.

Note :- Only calcium silicate false ceiling area will be measured from wall to

wall. No deduction shall be made for exposed frames / opening (cut outs)

having area less than 0.30 sqm. The calcium silicate ceiling tiles shall have

NRC. Value of 0.50 (Minimum) for Fine fissured / Spintone / Cosmos and

NRC for Globe, light reflection 85% non-combustible as per B.S. 476 part IV,

100% humidity resistance and also having thermal conductivity. 0.043° w/m KC

for the best thermal Insulation.

Electrical Items

76 Point wiring for Light/ Bell with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) 30.00 Pt. 739.32

both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper

wires, in following type of pipe to be erected concealed in/ on surface on

wall/ceiling complete with 6A Modular type switch/ bell push & accessories and

earth continuity of following type, erected on PVC / Metallic box, single

mounting base frame covered with textured / metallic front plate modules

erected on/ in wall/ ceiling as per pipe erected, with necessary Lamp holder/

ceiling rose/ H.D. Connector as directed. (g) with 16 swg HGS metal conduit

pipe and accessories painted black erected concealed in wall/ceiling complete

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

77 Point wiring for FAN with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both 9.00 Pt. 965.56

are of ISI marked 1.1 KV Grade FRLS PVC insulated multistrand copper

wires, in following type of pipe to be erected concealed in / flushed on

wall/ceiling complete with 6A Modular type switch and hum free EME four or

more step type electronic fan regulator with separately mounted and

accessories with earth continuity of following type erected on PVC / Metallic

box, single mounting base frame covered with textured / metallic front plate

modules erected on / in wall / ceiling as per pipe erected. with necessary ceiling

rose / H.D. Connector as directed. (g) with 16 swg HGS metal conduit pipe

and accessories painted black erected concealed in wall/ceiling complete, Cat-

78 Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin 7.00 Pt. 309.06

socket erected on PVC / Metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate modules erected on / in wall /

ceiling with following type accessories Cat-III

79 Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are 1.00 Pt. 1003.94

of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in

following type of to be erected concealed in / on surface of wall / ceiling

complete with Modular type switch & 5 pin Plug erected on PVC / Metallic box

covered with appropriate front plate modules erected on / in wall / ceiling as per

pipe erected with following type of accessories. [II] For 16A Plug with 2-2.5

sq.mm Cu. Wire, (g) with 16 swg HGS metal conduit pipe and accessories

painted black erected concealed in wall/ceiling complete, Cat-III

80 Providing following type of Modular Type Accessories mounted with PVC /

metallic/Wooden box, single mounting base frame covered with textured /

metallic/white front plate, modules erected with necessary connections as per

site situation directed by Engineer In charge.

(13) 6A/10A/16A/20A/25A/32A Single pole Modular MCB Switch, Cat-III 2.00 Nos. 310.07

(10) 6/16Amp. Universal socket, Cat-III 2.00 Nos. 199.98

81 Providing & erecting Switch board for Computer or electric apparatus 6.00 Nos. 1133.22

consisting of following modular type accessories mounted with PVC / Metallic

concealed / open box with single mounting base frame covered with textured /

metallic / white front plate,modules erected with necessary connections as

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug [B] For Modular Type Accessories, Cat-III

82 Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI 70.00 Mtr. 104.03

marked stranded Copper conductor wire in following type of pipe to be erected

concealed in / flushed on wall/ceiling, with 1.5 sq.mm copper conductor FRLS

PVC insulated stranded wire of green colour for earth continuity of following

size (a) with medium class Rigid PVC pipe and accessories, (b) 2 wire 2.5 mm²

83 Replacing old & u/s providing and erecting Mains with 1.1 KV grade FRLS PVC 30.00 Mtr. 140.39

insulated ISI marked stranded Copper conductor wire in following type of pipe

to be erected in / on wall / ceiling with 2.5 sq.mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth continuity of following size (a)

2 wire 4 sq. mm

(h) 4 wire 6 sq. mmm 10.00 Mtr. 326.23

84 Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 kv 4.00 Mtr. 97.97

grade ISI marked copper wires of following size to be erected as directed.(h)

2.50 Sq.mm 3 core round PVC sheathed

85 Providing and erecting FRLS-XLPE(IS:7098)(I)-88 ISI armoured cable 50.00 Mtr. 95.95

Aluminium conductor for 1.1 kV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables. (A) 2 core 4 Sq.mm

86 Decorative call bell Ting-tong box type 250 volts complete erected. 2.00 Nos. 71.71

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

87 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 25.00 Nos. 535.30

Watt assembled on single MCPCB, with housing used as a heat sink shall be

made of thick sheet Steel conforming to IS: 513/CRCA/ aluminium die cast

powder coated and high U.V. & corrosion resistance with diffuser with company

mark/name 160V to 270V, Power Factor more than 0.95, THD < 15%, CCT

3000 K to 6500K, Luminaire efficacy> 85 lumens/watt, LED

LED driver efficiency > 85% (fitting required LM-79 & LM-80 Certificates)

(NOTE: Below description have shown ranges of Wattage capacity of LED

ranges shown) (A) Tube Light with integral/ non-integral driver, (v) 36-40 Watts,

Surge-2 KV, IP-20, conventional 4 feet, Cat-III

88 Supplying and erecting led lamps with following wattage capacity of 220 to 240 1.00 Nos. 112.11

voltage, minimum 15000 burning hours life, 500 V in built-surge protection,

Polycarbonate diffuser, mounting suitable for E14 / E27 / B22 lamp holders, pf

>= 0.5 (A) LED Lamps integral type, with PC diffuser suitable LAMP holder (b)

5 to 8 watts.

89 Providing and erecting Approved make Ceiling fan with double ball bearing ISI 9.00 Nos. 1596.81

mark with condenser A.C. 23OV.50 c/s.1200 mm. sweep complete, canopy

erected on existing hook or clamp with earthing. [Make shall be approved by

Engineer in charge]

90 Supplying and erecting 19/20 mm. nominal bore Medium Class M.S. Pipe down 9.00 Mtr. 108.07

rod erected duly painted for fan complete with necessary 24/ O.20, 3 core

flexible wire with earthing.

91 Supplying & erecting Fan Hook of 10 mm M.S. Round bar grouted in RCC slab 9.00 Ea 43.43

with Making the site as original.

92 Supplying & erecting approved make low noise decorative exhaust fan having 4.00 Nos. 1366.53

square frame ABS body with inbuilt lowers & square frame. 250mm with

RPM Cat.II

93 Providing and erecting Sheet Steel powder coated MCB distribution board - 1.00 Nos. 2913.85

flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail,

Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs. (The DBs should be used of same company of MCB

to be used) suitable for (B) three phase incoming and single phase horizontal

type outgoing Per phase isolation type (PPI) (b) sheet steel double door (ii)

94 Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C

Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box

having following capacity.

(b) 40 Amp. Cat-III 3.00 Nos. 736.29

95 Providing and erecting Approved make RCCBs conforming to IS: 12640 and 4.00 Nos. 2166.45

having sensitivity of 30 mA and Short Circuit withstand capacity of 10 KA and

suitable for operation on single phase 240 V, 50Hz. having characteristic of

quick action & tripping with all advance feature & do not incorporate any

electronic component for following Max. rating erected as directed (i) 25 Amps,

96 Providing and erecting Miniature circuit breaker single pole 6A to 25A suitable 18.00 Nos. 123.22

to operate on 240 V A.C. system and having breaking capacity 10 KA to be

erected in existing box confirming to IS 8828/1996 with ISI Mark. Cat-III

97 Providing and erecting Approved make Four pole moulded case circuit breaker 1.00 Nos. 6790.23

having breaking capacity ICU of 25 KA. at 415 V,having normal current rating

up to 25 A to 100A. with Fixed thermal & magnetic release suitable to work on

A.C. supply 50 Hz. with all internal connections, spreader tinned copper &

complete erected in existing 16 G.M.S. housing.Cat III

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

98 Supplying and erecting triple pole & neutral 440V / 500V panel mounting

Copper Busbars with four equal Nos. of electrolyte bus having current density

not more than 1.6 Amp. / sq.mm (Rated current / cross section area) duly

wrapped with colour insulating tape for phase sequence of following current

carrying capacity, erected with necessary bus bar supports /insulators, main

cable socket to each bar, erected in existing cubical panel with necessary

connections. (B) Suitable for 200 Amp. capacity

(A) Suitable for 100 Amp. Capacity 0.40 Rn. 1961.42

99 Providing & erecting weather proof, dust & vermin proof, floor mounted front 0.70 Sq.m 10468.65

operated indoor type cubical panel board necessary IP-42 and above protection

as per approval from engineer incharge made from 14 SWG thick CRC M.S.

sheet for outer body & doors, 16 SWG thick CRC M.S.sheet for internal

partitions with necessary accesories, supporting angles / flats channel including

cutting, bending, drilling, welding, riveting with internal partitions & cable alley

as per requirements & instruction of engineer-in-charge with erection of

supplied switch gears, BUSBARS, suitable size of inter connecting PVC copper

wire / copper-aluminium strips, rubber grommets, rib, bakelite control

fuses/MCB for measuring instruments, earth bus & earth bolts, foundation

flange - bolts-base Plates, sufficient nos. of hinged doors, handles with locking

arrangement and rubber gasket, heavy duty end terminal connection, danger

notice board, necessary ventilation, earthing strip complete. The Panel shall be

painted with epoxy powder coating.

(The rates excludes the cost of switchgears, bus bars, inter connecting mains &

Copper Aluminium strips, meters, fuses etc. The dimension shall be measured

excluding base beams) The panel shall be supplied with following approved

manufacturers with following size. (A) locally fabricated panel board (i) with

100 Supplying and erecting approved make panel mounting type Digital Ammeter 1.00 Nos. 1558.43

having 3 digits LED display, external CT operated, calibrated for 0 to

Amps suitable to operate on 500 Volt AC, erected on existing panel board with

all connection, wiring etc. with manufacturers calibration certificate.

101 Supplying and erecting approved make panel mounting type Digital Voltmeter 1.00 Nos. 1275.63

having 3 digits LED display, 0 to 750 AC Volts range erected on existing panel

board with all connection, wiring etc. with manufacturers calibration certificate.

Supply 500 V on existing panel board with necessary connections.

103 Supplying and erecting approved make suitable panel indicator LED type lamp, 3.00 Nos. 43.43

lens cover, complete erected with necessary connections.

104 Providing & erecting L.T. Current Transformer with bar primary 50/5 to 1000/5 3.00 Nos. 274.72

ratio 15 VA burden erected in existing CRCA box duly secured with insulating

materials connected to the meter

105 Poviding and erecting Mains with ISI marked, 1.5KV grade electrolyte multi Mtr.

stranded, annealed copper conductor with heat resistant PVC insulated

conforms to IS 694, IEC - 227 erected in existing pipe of following size

(Specifically for control panel, relays, power switchgears, motor starters &

control wiring) with required size of copper lugs, nuts and bolts if required.

(f) One wire 10.00 sq. mm 10.00 Mtr. 145.44

(h) One wire 25.00 sq. mm 4.00 Mtr. 295.93

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

106 Supplying & erecting earth pit of minimum bore dia.150mm size approved 1.00 Nos. 4591.46

make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-

1987 made of corrosion free hot dipped G.I. Pipes having Outer pipe dia of

50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-

250 Micron galvanising, connection terminal dia of 12mm with constant ohmic

value surrounded by highly conductive compound with high charge dissipation

suitable for following type of applications with chamber and heavy duty cover.

(A) (approved make OEM has to submit test certificate including value of earth

resistance of installation duly stamped and signed by agency and officer

Incharge has to ensure the value of earthing resistane mentioned in test

Certificate) & having back filling compound of (B) Inner chemical (CCM

Compound)- Resistivity :- 0.2 ohm / meter testing as per IEC 62561-2017,

Voltage drop :- < 1 volt at no load & dry form, Sulphar content:- <2% (C) Back

fill Compound :- Earthing compound should be capable to retain moisture for

long time necessary test report must be submitted by Agency.

(a) For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

107 Providing and erecting FRLS-XLPE (IS:7098)(I)-88 ISI armoured cable 10.00 Mtr 168.67

multistrand / Solid Aluminium conductor for 1.1 kV. to be laid on wall with

necessary clamps or in existing trench / pipe of following size of cables (C)

core 10 Sq.mm

108 Providing and fixing heavy duty flange type brass cable gland with rubber ring 2.00 Ea 38.38

for PVC insulated armoured cable complete with out going tails, insulating tape

etc. for following size of cables. (C) 2 to 4 core 10 Sq.mm

(A) 2 to 4 core 2.5 / 4 Sq. mm 4.00 Ea 33.33

109 Supplying and erecting LED street light / Flood light fittings with High power 4.00 Nos. 4415.72

White LEDs wattage of 3 Watt and above assembled on single MCPCB,

efficiency more than 130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/ lenses, with toughened glass

with company mark/name engraved or embossed 160 to 270 V, Power Factor

more than 0.95, THD < 10%, CCT 3000 K to 5700K, Uniformity ratio >0.45,

Luminaire efficacy> 100 lumens/watt. LED driver efficiency > 85%. (fittings

required LM-79 & LM-80 certificates) (NOTE: Below description have shown

any wattage capacity between the ranges shown) (A) Street Light (IP-65),

Surge protection -4KV integral and Light must have 440VAC line supply with

over-voltage protection. (B) Flood Light (IP-65), Surge -4KV (iii) 36-47 watts

110 Providing and erecting Miniature circuit breaker single pole 0.5A to 2A system 4.00 Nos. 297.95

and having breaking capacity 10 KA to be erected in existing box confirming to

IS 8828/1996 with ISI Mark

111 Supplying & erecting approved make SMC press moulded composite FRP loop- 4.00 Nos. 476.72

in, loop-out approx. 2mm thick box complete with Bakelite connector strip 5way

(3P+N+E), DIN rail for mounting mob & hinged doors as per requirement

having locking arrangements with mounting clamp with nuts, bolts & washers

suitable for erection on pole with cable clamps & earth bolt of following size of

box. (c) 150mm x 125mm x 100mm [deep]

112 Replacing old & u/s Solder less crimping type Aluminium lugs conforming to IS

suitable for cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut bolts in an

approved manner.

(A) 1.5/ 2.5/4/6 Sq.mm 16.00 Nos. 6.06

(B) 10 Sq.mm 8.00 Nos. 13.13

113 Solder less crimping type Copper lugs conforming to IS suitable for cable of 12.00 Nos. 8.08

following size evenly crimped with high pressure tool & connected to switchgear

terminals with brass/cadmium plated nut bolts in an approved manner. (A)

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

114 Supplying and erecting approved make Segment time switch suitable for 1.00 Nos. 2226.04

230V+10% 16A. floating contacts with 24 hour dial having15/30 min. segments

with early manual override switching for on & off without influencing the

program sequence with quartz time switch with power reserve, housed in fire

proof thermoplastic enclosure & transparent cover terminal covers erected as

required wire necessary connection erected as directed.

TOTAL Rs.

i.e. Rs. Thirty Four lacs Fifty thousand Seven hundred Fifty Two and One paisa only.

I/We am/are willing to carry out the work @ ______________ % above/below percent (Should be written

in figures and words) of the estimated rate mentioned above. Amount of my /our tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

Net Rs. ___________________________ Total Rs. ________________________

In words ____________________ In words ____________________

1. The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-

Charge for which no extra payment shall be made.

2. The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3. GST and Income tax TDS will be deducted at a source while making payments of bills.

4. In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-

10/2017 Cement Consumption/16/C, Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where there is

a change as per actual mix design the cost of difference of cement consumption have been deducted from the

rate of original item at the rate of input rate mentioned in all the tender.

5. The Contractor will have to submit the all required mix design at his own cost before execution as

directed and to be approved from the Engineer in charge.

6. Credit for dismantalled materials of amount of Rs. 30,000.00 must be recovered from 1st R.A. bill of

Contractor's.

Above all items of "Schedule-B" with Item Description, Unit, Rate & Amount have verified by me and

found order.

Deputy Executive Engineer Sr. Divisional Account Officer Executive Engineer

Dabhoi (R & B) Sub Division, Dist. (R & B) Division, Dist. (R & B) Division,

Dabhoi Vadodara Vadodara