ADDITION / ALTERATION AND SPECIAL REPAIR TO OFFRS MD ACCN AT TEZPUR UNDER GE (S) TEZPUR

Amount

B/R WORKS

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for and rubbish off the premises complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floor and pavings n.exc. 15cm thick ( below or above ground level) including rubbish off the premises complete all as specified and as directed.

Demolition of plain cement concrete of any description and in any position not otherwise specifally provided for including rubbish off the premises complete all as specified and as directed.

M & L for Rolled Mild Steel work confirming to Fe 410 - W (Gde - E - 250) Quality - A as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates complete all as specified and as directed.

Dismantling of boarding of any description, fixed in any position with nails including rubbish off the premises complete all as directed.

Dismantling Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings including ridge and rubbish off the premises complete all as specified and as directed.

S & F of Prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick and colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

S & F of Prepainted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick and colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

Demolition of old damaged existing water proofing treatment on RCC roof of any description and specification and removing from site and cleaning the surface thoroughly complete all as specified and as directed.

M&L for 15mm thick in CM (1:4) on existing roof surface true to level after applying cement slurry @ 3 KG/SQM and applied one coat of cold bitumen primer conforming to IS:3384:1986 @ 0.30 Ltr/SQM on the cleaned plastered surface complete all as specified and as directed.

Supply and laying 3mm thick APP based polymeric membrane of approved manufacturer with weight not less than 3.60 Kg/Sqm, reinforced with non woven polyster fabric weight not less than 150 gms/Sqm. The overlap shall be not less than 100mm on transverse direction and 75mm on longitudinal direction and sealing overlaps and applying evenly one coat of aluminium paint @ 0.10 Litre/Sqm over the APP based polymeric membrane complete all as specified and as directed.

M&L for cutting out grooves to 'V' section in existing roof or terrace, cleaning out, wetting grouting with cement and sand slurry (1:3) complete all as specified and as directed.

M&L for taking down chowkhats and shutters (without taking off shutters from the frame) n.exc 1.5 sqm each and removing from site complete all as specified.

M&L for taking down chowkhats including shutters (without taking off shutters from the frame) exc 1.5 sqm and n.exc 4 sqm each and removing from site complete all as specified.

S & F pressed steel door frames of size 165 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and as directed

All as per serial item No. 1.15 here in above but of size 105 x 60mm complete all as specified and as directed

M&L for PCC (1:3:6) type C1 using 20mm grade brokenn stone aggregate as in padding, hold fasts, block filling, filling of steel chowkhats or similar work complete all as specified and as directed

M&L for 2nd class hard wood weather boarding, clean sawn, plain,20mm thick or feather edged 15mm to 20mm thick and fixed with 30mm lap complete all as specified and directed.

S&F factory made 30 mm thick flush shutter, solid core construction,with particle board core and ply wood face panels commercial type on both sides complete all as specified and as directed.

S & F 35mm thick glazed and skeleton shutters open, rebated and prepared to receive glass gauge etc. Divided into squares with plain chamfered or rounded, rebated sash bars, sizes of the members of the shutters as specified in SSR Part I, section 8, clause 8.23(a) complete all as specified and as directed.

S&F Mild steel 300mm, ordinary rat rail rod pattern springs, including roller and roller plate complete all as specified and directed.

M&L for plain fillets square, reclanqular or triangular in section wrought secured with nails/sawn/brads in 2nd class hard wood sectional area exc 3 but n exc 6 sqcm complete all as specified and as directed.

S & F solid door frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet reinforced with M.S. Square tube,supporting & fixing in opening as per specification & drawing complete all as specified and as directed.

S& F Factory made solid PVC moulded door Shutter 30 mm thick with 2mm thick Moulded Prelam PVC Sheet on the front face and 2mm Prelam PVC Sheet on back face with 2,4 or 6 raised panel design, supplying and fixing in frame at site as per specification & drawing complete all as specified and as directed.

S&F anodised aluminium frame (three track) for doors, windows, ventilators with one or more rebates including jointing cleat for fixiing etc complete all as specified and as directed.

S&F anodised aluminium window and ventilator shutters, sliding type without sash bar, aluminium section weighing 0.55 Kg/m including necessary jointing cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, 4 mm plain / coloured tinted glass and stainless steel wire mesh 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and suitable size slot will be provided in window type AC of etc. complete all as specified and as directed.

M&L for framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and as directed.

S&F factoty made steel ventilator with top hung shutter including hinges, steel peg stay, complete all as directed.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in squares n.exc 0.5 sqm in each pane complete all as directed.

S&F floor door stopper having 140mm overall length of cover plate of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor all as specified and directed

S&F mild steel medium weight cold rolled butt hinges 100 mm long complete all as specified and directed.

S&F Butt hinges, 75mm extruded aluminium alloy with galvanised mild steel hinge type C-21 complete all as specified and directed.

S&F aluminium anodised, barrel tower bolt of extruded section 200mm long complete all as specified and directed.

All as per item No 1.33 here-in-before but 150mm long complete all as specified and as directed.

S&F 125 mm Hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed.

S&F aluminium alloy anodised sliding door bolts with hasp and staple (bolt type) 12mm dia bolt , 300mm long and fixing clips of sheet, cast or extruded sections and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections on cast aluminium alloy and fixed complete all specified and as directed.

S&F 150mm long extruded aluminium alloy handle, fabricated type, anodised complete all as specified and directed

S&F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

Taking down old unserviceable 20mm dia anodised aluminium alloy curtain rod with two Nos of socket and removing from site complete all as specified and directed.

S&F 20mm dia anodised aluminium alloy curtain rod with two Nos of socket complete for doors/window opening including removing old rod from site complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding, removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Roughening surfaces of old concrete floor by picking, sweeping, clean and washing down with water to remove dust,etc and rubbish off the premises complete all as directed .

M&L for brushing with neat cement slurry @ 3.0Kg of cement per sqm complete all as directed.

M&L for Vitrified Ceramic tiles 10mm thick (square/rectangular) dark shade,double charged polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM (1:4) on brick or concrete surfaces for fixing of tiles as in floor complete all as specified and as directed

All as per item No 1.44 here-in-above but as in skirting over 10mm thick screed bed in CM (1:4) complete all as specified and directed.

M&L for colored non skid Ceramic rectified tiles 6 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in CM (1:4) on brick or concrete surfaces for fixing of tiles as in floor complete all as specified and as directed.

M&L for coloured Glazed Ceramic tiles 450 x 300 mm x 6 to 8mm thick, in skirting /dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm screed bed in cement mortar (1:4) complete all as specified and directed.

M&L for Temp shield tiles size 300mm x 300mm x 10mm thick, set, jointed and pointed in neat cement slurry in floors and pointed in white or coloured cement to match over 20mm thick screed bed in CM (1:4) complete all as specified and directed

M&L for machine cut Kota Stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over 15mm thick screed bed in CM (1:4) complete all as specified and as directed.

M&L for machine cut Kota Stone 18-20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over 10mm thick cement plater in CM (1:4) complete all as specified and as directed.

M&L for Polythene film black 150 micron laid in floors complete all as specified and as directed.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations all as specified and directed.

S&F plain aluminium sheeting 0.71 mm thick Alloy 31000H4, as in ridges, hips, vally gutter , drip and straight flashing (length and girth as fixed) complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar including rubbish off the premises complete all as directed.

M & L for brick work using old size with sub class 'B' bricks straight or curved on plan to any radius in half brick thick walls built in CM(1:4) complete all as specified and as directed.

M & L brick work using old size with sub class 'B' bricks straight or curved on plan exc. 6 mtr nean radius, in CM (1:6) complete all as specified and as directed.

Taking down cement plaster on brick walls incl racking out joints, hacking key & scrubbing down with water and rubbish off the premises complete all as directed.

M&L for 10mm thick rendering in CM(1:6) on fair faces of brick work or concrete surfaces and finished the surface even & smooth without using extra cement complete all as specified and as directed.

M&L for 15mm thick rendering in CM (1:4) in two layers and finishing layer mixed with WPC (WPC shall be measured and paid seperately) on fair faces of brick work or concrete surfaces and finished the plastered surface even and smooth without using extra cement complete all as specified and as directed.

M&L for 5mm thick rendering in CM (1:3) in ceiling or concrete surfaces and finished the surface even & smooth without using extra cement complete all as specified and as directed.

Supply only integral WPC of ISI marked complete all as specified and as directed.

M&L RCC (1:2:4) Type B-1 (20 mm graded stone aggregate) in slabs supported on walls, and in shelves and the like complete all as specified and as directed.

Formwork to soffits of suspended slabs such as cooking slab and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

Dismantling ceiling board including cover fillets and rubbish off the premises complete all as specified and as directed.

Dismantling of fillets, rails etc under 40 sqcm in section unframed work complete all as specified and as directed.

Dismantling of timber scantlings 40 Sqcm & over in section, in any position unframed work complete all as specified and as directed.

S&F false ceiling with powder coated exposed GI grid suspension system Everest E-Grid T-2430 or equivalent load carrying capacity with mid span deflection not exceeding 1/360 span with hanger spacing of 1200 mm c/c consisting of Main Runner (3600 mm long, 0.25mm thick, 38 mm height) cross Tee (1200mm/600mm long, 0.25mm thick, 27mm height) and Wall Angle (3600mmlong,0.4mm thick,22mm height) The wall angle shall be fixed on PVC Dash fasteners on the primeter of the wall by steel screws with distance 300 c/c. The Main Runner to be placed @ 1200 mm, The Cross Tee 1200mm will be inserted in the pre-cut slots of main runner at a regular interval of 600 mm to form a modular grid of 1200mm x 600mm. Additional Cross Tees of 600mm x 600mm. Grid of module size 600mm x 600mm shall be supported by 6mm Dia GI wire from purlins/soffit. 4 mm thick High pressure Steam Cured Everest Non Asbestos Fibre Cement Designer Ceiling Board or equivalent quality haveing Density > 1200 Kg/m3, size 595 x 595. confirming IS 14862 & Type B Category III of ISO 8336, tested as per AS-1530 part-3 complete all as specified and as directed.

Demolition and breakingup drain pipes ( SGSW, AC or reinforced concrete ) set in cement mortar 100mm bore including removing from site complete all as specified and as directed.

S&F PVC (SWR) pipes single socketed in any length with rubbe ring joints fixed to walls 110mm bore complete all as specified and as directed.

All as per item No 1.69 here-in-before but 75mm bore complete all as specified and as directed.

S&F PVC (SWR) pipes 75mm single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and as directed.

S&F PVC (SWR) pipes 110mm single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and as directed.

S&F PVC (SWR) bends any radius 75mm bore complete all as specified and as directed.

PVC(SWR) junction single, (Single 'T') equal or unequal 75 mm bore complete all as specified and as directed.

S&F PVC (SWR) bends any radius 110 mm bore complete all as specified and and as directed.

S&F PVC(SWR) junction single, (Single 'T') equal or unequal 110mm bore complete all as specified and as directed.

S&F PVC(SWR) vent cowl 75mm bore complete all as specified and as directed.

Taking down existing damaged IWC alongwith complete PCC and lime concrete from sunken floor and rubbish off the premises and providing new IWC and water proofing treatment to sunken floor as per following stages :- (i) 15mm thick plastering in CM (1:2) with WPC at all around and base of sunken floor with proper slope. (ii) Applying a coat of 85/25 gde hot bitumen @ 0.7Kg/Sqm over a coat of bituminous primer @0.5Kg/Sqm and then pasting of polythene film 150 micron, natural colour with cold cut back adhessive. (iii) Fixing of 20 mm dia CPVC pipe (medium grade) spout of length 45cm in proper slope. (iv) Supply & fixing of vitreous china sqatting pan " ORISSA" pattern, size 580 x 440 mm white with integral footrest, P/S trap etc complete including providing lime concrete and cement concrete to fill up the sunken floor PCC (1:3:6) using 20 mm graded stone aggregate after testing of water tightess complete all as specified and as directed.

Taking down existing damaged EWC alongwith complete PCC and lime concrete from sunken floor and rubbish off the premises and providing water proofing treatment to sunken floor as per following stages :- (i) 15mm thick plastering in CM (1:2) with WPC at all around and base of sunken floor with proper slope. (ii) Applying a coat of 85/25 gde hot bitumen @ 0.7Kg/Sqm over a coat of bituminous primer @0.5Kg/Sqm and then pasting of polythene film,150 micron, natural colour with cold cut back adhessive. (iii) Providing lime concrete and cement concrete to fill up the sunken floor (PCC 1:3:6) after testing of water tightness complete all as specified and as directed.

Taking down old unserviceable vitreous China squatting pan, ‘Orissa’ pattern, any size and removing from site complete all as specified and as directed.

S&F vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete all as specified and as directed.

Taking down old unserviceable vitreous china wash down water closet pan (Pedestal pattern) including rubbish off the premises complete all as specified and as directed

S&F vitreous china wash down water closet pan (Pedestal pattern) white (excluding flushing cistern and flush pipe) including seat cover white closed type including rubbish off the premises complete all as specified and as directed

Taking down old unserviceable PVC Low level flushing cistren any capacity and removing from site complete all as specified and as directed.

S & F PVC Low level flushing cistren 10 Ltr capacity ISI marked including all fittings such as flush pipe brackets etc and removing old cistern complete all as specified and as directed.

Taking down old unserviceable PVC connection pipe and removing from site complete all as specified and as directed.

S&F 15 mm dia 600 mm long PVC connection pipe with two CP nuts at each ends with rubber washer complete all as specified and as directed.

Taking up or down steel tubing and connections 15mm bore including removal complete all as specified and as directed.

All as per item No 1.88 here-in-before but 20mm bore complete all as specified and as directed.

Supply and laying 32mm outer diameter CPVC pipes of SDR 11 & plain CPVC fittings jointed with CPVC solvent cement only on walls/ceiling or laying in floors complete all as specified and as directed.

Supply and laying 20mm outer diameter CPVC pipes SDR 11 & plain CPVC fittings jointed with CPVC solvent cement only on walls/ceiling or laying in floors complete all as specified and as directed.

Taking down old unserviceable 25 mm bore Gun-metal, globe or gate valves, and removing from site complete all as specified and as directed.

S&F 25mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

Taking down unserviceable 15mm Gun-metal, globe or gate valves,and removing from site complete all as specified and as directed.

S&F 15mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe including removing old valve complete all as specified and as directed.

Taking down old uinserviceable Angular stop cock cast copper alloy CP with wall flange for 15mm bore and removing from site complete all as specified and as directed.

S&F Angular stop cock cast copper alloy CP with wall flange for 15mm bore complete all as specified and as directed.

Taking down old uinserviceable 15mm bore two way bib cock cast copper alloy CP fancy type ,with wall flange and removing from site complete all as specified and as directed.

S&F 15mm bore two way bib cock cast copper alloy CP fancy type ,with wall flange screwed down for iron pipe or union , complete all as specified and as directed.

Taking down old uinserviceable 15mm bore bib cock with nozzle cast copper alloy CP fancy type ,with wall flange and removing from site complete all as specified and directed.

S&F 15mm bore bib cock with nozzle cast copper alloy CP fancy type ,with wall flange screwed down for iron pipe or union , complete all as specified and directed.

Taking down old uinserviceable 15mm bore health faucet (ABS body) with 8mm Dia, 1 m long flexible tube & wall hook and removing from site complete all as specified and as directed.

S&F 15mm bore health faucet (ABS body) with 8mm Dia, 1 m long flexible tube & wall hook including removing old faucet from site complete all as specified and as directed.

Taking down old uinserviceable chromium plated toilet paper holder and removing from site complete all as specified and as directed.

S&F chromium plated toilet paper holder including removing old paper holder from site complete all as specified and as directed.

Taking down old uinserviceable towel ring of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats and removing from site complete all as specified and as directed.

S&F towel ring of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats(Minimum weight 90gms) complete all as specified and as directed.

Taking down old uinserviceable glass shef assembly 60Cm long, 5.5mm thick sheet glass shelf 12cm wide with railing and removing from site complete all as specified and asdirected.

S&F glass shef assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and asdirected.

Taking down old uinserviceable concealed stop cock cast copper alloy CP with wall flange for 15mm bore and removing from site complete all as specified and as directed.

S&F concealed stop cock cast copper alloy CP with wall flange for 15mm bore including removing old one from site complete all as specified and as directed.

Taking down old uinserviceable 15mm dia Stop valves fancy type chromium plated and removing from site complete all as specified and as directed.

S&F 15mm dia Stop valves fancy type chromium plated, screwed down, high pressure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions including removing old valve from site complete all as specified and as directed.

Taking down old uinserviceable PVC (SWR) floor trap 75 mm size plain with grating and removing from site complete all as specified and as directed.

S&F PVC (SWR) floor trap 75 mm size plain with grating including jointing with solvent cement complete all as specified and as directed.

Taking down old uinserviceable bib tap 15mm bore, fancy type, chromium plated and removing from site complete all as specified and as directed.

S&F bib tap 15mm bore, fancy type, chromium plated, screwed down for iron pipe or for brass ferrule including removing old tap from site complete all as specified and as directed.

Taking down old uinserviceable tubular Towel rail chromium plated 600mm long 20mm dia D type and removing from site complete all as specified and as directed.

S&F tubular Towel rail chromium plated 600mm long 20mm dia D type complete all as specified and as directed.

Taking down old uinserviceable 600mmx450mm bevelled edge mirrorand removing from site complete all as specified and as directed.

Taking down old uinserviceable sinks with drainage board any size and removing old sink from site complete all as specified and as directed.

S&F sinks with drainage board ISI marked made of stainless stell 1 mm thick kitchen or laboratory with plugs, washers and wastes " including bedding in cement mortat to dwarf wall or including fixing cantilever brackets and connecting unon pipe overall size 915mm x 460mm and bowl size 410mm x 330mm x 160mm including removing old sink from site complete all as specified and as directed.

Taking down old uinserviceable plate rack any size and removing from site complete all as specified and as directed.

S&F plate rack ISI marked made out of stainless steel sheet 0.5 mm thick overall size 760mm (H) x 900 mm (W) x 250 mm (D) with three shelf complete all as specified and as directed.

Taking down old uinserviceable central hole basin mixer without pop-up system and removing from site complete all as specified and as directed.

S&F central hole basin mixer without pop-up waste system complete all as specified and as directed.

Taking down old unserviceable brass chromium plated shower rose 125 mm dia and removing old one from site complete all as specified and as directed.

S&F brass chromium plated shower rose 125 mm dia including removing old one from site complete all as specified and as directed.

Taking down old uinserviceable 32 mm dia 610 mm long PVC waste pipe and removing from site complete all as specified and as directed.

S&F 32 mm dia 610 mm long PVC waste pipe suitable for WHB including removing from old one site complete all as specified and as directed.

Taking down old uinserviceable 40 mm dia 610 mm long PVC wate pipe and removing from site complete all as specified and as directed.

S&F 40 mm dia 610 mm long PVC wate pipe suitable for sink including removing old one from site complete all as specified and as directed.

Taking down old uinserviceable 15mm dia CP wall mixer 3-in-1and removing from site complete all as specified and as directed.

S&F 15mm dia CP wall mixer 3-in-1 for mixing hot & cold water screwed down for iron pipe and fixed including removing old one from site complete all as specified and as directed.

Taking down old uinserviceable Grating doom 100mm dia of CP and removing from site complete all as specified and as directed.

S&F Grating doom 100mm dia of CP complete all as specified and as directed.

Taking down old uinserviceable vitreous China wash basin, white, flat back, any size and removing from site complete all as specified and as directed.

S&F vitreous China wash basin, white, flat back, size 550 x 400 mm including brackets, cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of waste pipe including removing old basin from site complete all as specified and as directed.

Taking down old uinserviceable Pillar taps 15mm bore fancy type ,chromium plated and removing from site complete all as specified and as directed.

S&F Pillar taps, 15mm bore fancy type ,chromium plated, screwed down high pressure, with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed.

S&F 40 mm low density polyethylene (HDPE) pipes complete all as specified and as directed.

M&L for preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over a coat of wall primer over a coat of smooth layer of wall care putty complete all as specified and as directed.

M&L for complete removal of existing treatment of wall surfaces and applying two coats of oil bound distemper over a coat of wall primer over a coat of smooth layer of wall care putty complete all as specified and as directed.

M&L for preparation of new wall surfaces and applying three coats of white wash on wall complete all as specified and as directed.

M&L for preparation of old wall surfaces and applying one coat of white wash on wall complete all as specified and as directed.

M&L for preparation of new ceiling surfaces and applying three coats of white wash on Ceilling complete all as specified and as directed.

M&L preparation of old ceiling surfaces and applying one coat of white wash on Ceilling complete all as specified and as directed.

M&L preparation of old ceiling surfaces and applying two coats of white wash on Ceilling complete all as specified and as directed.

M&Lfor preparation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint (1st quality) over a coat of pink primer complete all as specified and as directed.

M&L for French polishing on surfaces of any description, width or girth including cleaning and preparing the furface including a coat of wood filler on new works with two or more coats for making sine complete all as specified and as directed.

M&L for preparation of new steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint (1st quality) over a coat of red oxide primer complete all as specified and as directed.

M&Lfor preparation of old wooden surfaces over 10 cm width or girth and applying one coat of synthetic enamel paint (1st quality) complete all as specified and as directed.

M&L for preparation of old steel surfaces over 10 cm width or girth and applying one coat of synthetic enamel paint (1st quality) complete all as specified and as directed.

M&L for newly plastered surfaces of external wall and applying two coats of apex ultima weather coat paint over two coats of damp shield over a thin layer of wall care putty complete all as specified and as directed.

M&L for complete removal of existing treatment of external wall surfaces along with preparation of smooth wall surfaces and applying two coats of apex ultima weather coat paints over two coats of damp shield over a thin layer of wall care putty etc complete all as specified and directed.

M&L 75 mm thick PCC (1:3:6) type C-2 (using 20mm graded aggregate) as in plinth protections / path and laid in alternate bays including providing and filling with bituminous filler material at the interval of 1.5 meter complete all as specified and as directed.

M&L for sand cushioning / filling under floor or in foundations including watering and consolidation complete all as specified and as directed.

S&F soap dish chromium plated complete all as specified and as directed.

S&F Liquid soap container of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 105 gms) complete all as specified and as directed.

Taking down shutter of any description n.exc 1 Sqm each and removing from site complete all as specified and as directed.

S&F 25mm thick Factory Made flush shutter, solid core construction, with particle board core and plywood, commercial type on both sides with lipping/frame to match complete all as specified and directed.

M&L for 18/19 mm thick plywood BWR grade (ISI marked) fixed wirh screws to timber frame complete all as specified and as directed.

M&L for 2nd class hard wood plain, solid straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue painned at joints, complete all as specified and as directed.

M&L for machine pressed precast conctete interlocking Paver Block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade as approved by GE complete all as specified and as directed.

Excavation in post holes (or similar holes) soft and loose soil each n. exc 0.5 cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good the disturbed surface complete all as specified and as directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.50m deep and getting out soft/loose soil complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for including removing from site complete all as specified and as directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

All as per item Srl item No. 2.44 here-in-before but 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders complete all as specified and as directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished surfaces of concrete flat complete all as specified and as directed.

Formwork to sides of pillars, posts, struts, piers, columns, and stanchions rough finished surfaces of concrete square, rectangular or polygonal complete all as specified and as directed.

M&L for RCC (1:1.5:3) concrete with using 20mm graded stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete complete all as specified and as directed.

M&L for RCC (1:1.5:3) concrete with using 20mm graded stone agg as in columns, pillars, piers, posts and struts complete all as specified and as directed.

M&L for providing precast cement concrete (1:2:4), type B1 using 20mm graded aggregate as in coping or water troughts and the like including weathring, slightly rounded or chamfered angles and throating complete all as specified and as ditected.

S&F mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and as ditected.

M&L for PCC (1:4:8) type D2 using 40mm graded aggregate in foundation filling complete all as specified and as directed.

M&L for 75mm thick PCC (1:4:8) type D2 using 40mm graded aggregate in sub base complete all as specified and as directed.

M&L for 25mm thick PCC (1:2:4) type B-1 using 20mm graded aggregate in sub base complete all as specified and as directed.

M&L for PCC (1:3:6) type C2 using 40mm graded stone agg as in foundation filling and mass concrete as in post holes and drain complete all as specified.

M&L for PCC (1:3:6) type C2 using 40mm graded stone agg as surface channels and drain complete all as specified and as directed.

M&L for 50 mm thick PCC (1:3:6) type C2,using 40mm graded aggregate as in flooring finsihing cement concrete surface even and smooth withot using extra cement complete all as specified and as directed.

M&L for glass dividing strips, 3mm thick 38 mm width complete all as specified and as directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc. 25cm in soils complete all as specified and as directed.

Removing excavated material not exc. 50mtrs and depositing where directed at a level not exc. 1.50mtr above the starting point complete all as specified and as directed.

M&L for 18-20mm thick Granite stone (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like fixed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. over 20mm thick screed bed in CM (1:4) complete all as specified and as directed.

M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall)12 mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shed of granite over 10mm thick cement plater in CM (1:4) complete all as specified and as directed.

Removing building materials etc (other than spoil payable under Itms 03028 to 03031 in section-3 -Earth work) to a distance of 500 metres or part thereof (upto 1.0Km total distance) complete all as specified and as directed.

S&F stainless steel designer cup & saucer basket of size 530 mm wide, 505 mm depth and 100 mm height complete all as specified and directed.

S&F adustable wide angle peephole door eye / viewer peep sight hole home security for main door complete all as specified and directed by GE.

S&Fstainless steel perforated cutlery basket of size 530 mm width, 505 mm depth and 100 mm height complete all as specified and directed.

S&Fstainless steel designer plain basket of size 530 mm width, 505 mm depth and 150mm height complete all as specified and directed.

S&Fstainless steel fixed single pull out basket of size 160 mm width, 505 mm depth and 530mm height complete all as specified and directed.

S&Fsoft closing telescopic channel 18 " zinc (45 kg) suitable for baskets/drawers complete all as specified and directed.

Supply and fix stainless steel designer thali/plate basket comb of size 530mm width, 505mm depth and 200 mm height complete all as specified and directed.

S&F stainless steel handles fancy type 128 mm size complete all as specified and directed.

S&F PVC board 18 mm thick, exterior grade, fixed with screws complete all as specified and directed.

S&F magnetic catch suitable for cabinets and shelves, fixed with screws complete all as specified and directed.

S&F 30mm width of flaps (when open) continuous (piano) hinges mild steel, bright finish or electroglvanised complete all as specified and directed.

M&L for 0.9 mm thick decorative laminate type 1 of surface finish, colour and pattern as approved by GE, fixed with approved adeshive as per manufacturer's instructions complete all as specified and directed

E/M WORKS (INTERNAL)

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and as directed.

M&L for concealed point wiring with 1.5 Sqmm FRLS PVC insulated and unsheathed single core copper conductor multistranded 1100 volts grade, ISI marking drawn through and existing non metallic PVC rigid conduit and conduit acessories, medium grade, ISI marking, concealed with and including modular metal flush box and modular with frame for fixing switches, sockets, including one run of 1.5 sq mm FRLS PVC insulated unsheathed single core copper conductor green colour as in earth continuity wire and connecting to earth dolly for One Light Point controlled by one switch complete including cutting chases for conduits and making good the disturbed surface by putty and matching the colour of wall with the existing colour of the wall (wash/paint/distumper) wherever required (as per the existing condition) complete all as specified and as directed. Note:- The cost of Blanking plate if required shall deemed to be included in the unit price.

All as per Srl item No. 4.02 here-in-before but for one fan/Exhaust fan point complete all as specified and as directed.

All as per Srl item No. 4.02 here-in-before but for one 3 pin 5 Amp socket outlet on the Same Board complete all as specified and as directed.

All as per Srl item No.4.02 here-in-before but for one 3 pin 5 Amp socket outlet on Independent Board complete all as specified and as directed.

All as per Srl item No. 4.02 here-in-before but with 2 x 2.5 Sqmm + 1 x 2.5 Sq mm copper conductor cable for one 3 pin, 15 Amps Switch socket out let on independent Board complete all as specified and as directed.

All as per Srl item No. 4.02 here-in-before but for one bell point controlled by one one way switch 5 Amp complete all as specified and as directed.

All as per Srl item No.4.02 here-in-before but for one light point controlled by two Two Way switches complete all as specified and as directed.

All as per Srl item No.4.02 here-in-before but for one Fan point controlled by two Two Way switches complete all as specified and as directed.

S&F Sheet metal enclosure single pole & neutral with a two pin and earth pug and socket complete with one single pole MCB of 20 Amps complete all as specified and directed

S&F modular switch flush type, 6 amp, one way, 1 module complete all as specified and as directed.

S&F modular switch flush type, 6 amp, two way, 1 module complete all as specified and as directed.

S&F modular socket outlet, 5 pin, 6 amp, flush type, 2 module complete all as specified and as directed.

S&F modular switch, 16 amp, flush type, 1 module complete all as specified and as directed.

S&F modular socket outlet, 5 pin, 6/16 amp, flush type, 2 module complete all as specified and as directed.

S&F Modular bell push, flush type, 5 Amp, 1 module complete all as specified and as directed.

S&F Modular fan regulator stepped type 2 module, 120W complete all as specified and as directed.

S&F Ceiling rose 3 phase, PVC/Polycarbonate body complete all as specified and as directed.

Taking down old unserviceable submain wiring of any size and removing from site complete all as specified and directed.

M&L for sub main wiring with two run of 6.0 Sqmm PVC insulated un-sheathed FRLS stranded copper conductor single core cable, 1100 Volt along with one run of copper earth continuity wire 6.0 Sqmm PVC insulated un-sheathed FRLS stranded copper conductor single core drawn through PVC medium grade conduit and all accessories (ISI marked), concealed in wall/fixed to roof, ceiling etc. of size 25mm including cutting chases for conduits and making good the disturbed surface by Putty and matching the colour of wall with the existing colour (white wash/paint/distemper) wherever required(as per the existing condition), complete all as specified and as directed. Note: Copper conductor 2 run and one run of copper earth wire & one run of PVC conduit shall be measured as one unit length, connections of cables with MCB's or bus bars shall be done through appropriate size brass/copper thimbles.

All as per Srl item No. 4.20 here-in-before but 4 x 6.0 sq mm + 2 x 6.0 Sqmm earth wire complete all as specified and as directed.

All as per Srl item No. 4.20 here-in-before but 2 x 4.0 sq mm + 1 x 4.0 Sqmm earth wire complete all as specified and as directed.

Taking down old unserviceable DB's of any type & any capacity and metering panels and removing from site complete all as specified and as directed.

S&F MCB DBs, TPN, 415Volts 6 ways, double door, IP-43 protection with MCCB incommer, metal door, rated bus bars, earth bar, neutral links complete including blanking plates as required and fixed flush to wall/other surface complete all as specified and as directed.

S&F RCBO, FP, 32 Amps rating, 440Volts, 50Hz electromechanical with 10KA short circuit capacity with sensitivity of 100mA as per IS-12640-2 complete all as specified and as directed.

S&F factory made sheet metal enclosure for DBs double door (fixed flush to the wall), SPN, 240 Volt, 4 way, IP-43 protection with 200 Amp rated bus bar and 1.5 sq mm FRLS PVC insulated sheaqthed copper cable for earth continuity conductor and suitable for having MCBs and all disturbed surfaces of wall shall be made good to match the existing wall finishes complete all as specified and as directed.

S&F Power line vertical type TPN DB, double door, 6 way, IP-43 suitable for MCCB 100 Amps CRCA sheet metal enclosure with detachable gland plates for flush / surface mounting with bus bar neutral link and earh bar in concealed and all disturbed surfaces of wall shall be made good to match the existing wall finishes complete all as specified and as directed.

S&F Metering panel, powder coated factory made for mounting Electric Meter at stair case for 4 eelctric meters, box should be cubical indoor type modular design of not less than 900 mm x 900 mm x 200 mm, with 2 mm thick CRCA sheet steel with IP 52 tested, fabricated by welded frame construciton with CRCA frame section, compartmentalised (Modular) design. The cable entry shall be from the bottom and top of the panel provided with suitable diaq brass gland plates for provisioning specific bending radius for cable. The panel shall have opening arrangements front side mounted on hinges including fitting fixtures in wall complete all as specified and as directed.

Taking down old unserviceable MCB/ MCCB's of any type & capacity and removing from site complete all as specified and as directed.

S&F MCB, SP, 6 to 32 Amps, B series, 230 volts complete all as specified and as directed.

S&F MCB DP 6 to 32 Amps, B series, 230 volts complete all as specified and as directed.

S&F MCB TP 32 Amps, B series, 230 volts complete all as specified and as directed.

S&F MCCB 4 Pole 63 amps, B series, 415 Volts, 35 KA complete all as specified and as directed.

S&F wall mounted LED batten, polycarbonate housing & integrated electronic driver, LED light fittings flicker free, instant start with uniform light distribution 10W/ 9W, 2 ft indoor decorative with 2 core copper wire from ceiling rose to light fitting complete all as specified and as directed.

S&F wall mounted LED batten, polycarbonate housing & integrated electronic driver, LED light fittings flicker free, instant start with uiniform light distribution 20W, 4 ft indoor decorative with 2 core copper wire from ceiling rose to light fitting complete all as specified and as directed.

S&F 12 Watt LED fitting surface mounted, 6500K, colour temp ˃₌ 5700K with die cast body with premier diffuser ensuring glare free light including all its accessories complete all as specified and as directed.

S&F 9 watt LED fitting, B22 base, 3 star, colour temp 6500K complete all as specified and as directed.

S&F ceiling fan of sweep 1200, 5 Star rated mm with hanger including taking down existing old unserviceable ceiling fan and removing to MES store complete all as specified and as directed.

S&F 3 phsase, 4 wire, electronic tamper proof energy meters with LCD display of 10-60 Amp capacity 440V AC 50 Hz ISI marked and ceiling the meter (Top & Bottom covers) with suitable lead wire and connecting up incomming and outgoing cable connections to meter including taking down old unserviceable meter and removing to MES store including earthing of meter including testing and commissioning complete all as specified and as directed.

S&F exhaust fan of sweep 250 mm with louvers plastic rust proof body and blade, 1280 RPM, AC, single phase, 240Volts, 50 Hz, power input 45 watt, air delivery 860 CMH and connecting up complete including 3 core flexible multistranded copper conductor of size 0.75 Sqmm from ceiling rose to fan including cutting holes and making good the disturbed surfaces of wall in CM(1:4) and finishing the surface as per existing colour complete all as specified and as directed.

S&F heavy duty exhaust fan of sweep 300mm, MS body with anti dust painting, 4 blade with heavy duty motor and double ball bearing, 1320 RPM, AC, single phase, 240Volts, copper wounds, air delivery 1600 CMH and connecting up with all accessories like bird guard/ louvers shutters etc, including making connection with 3 core flexible multistranded copper conductor of size 0.75 Sqmm through flexible pipe including taking down existing old unserviceable exhaust fan and removing to MES store complete all as specified and as directed.

Taking down old unserviceable geyser of any capacity and removing it to MES store complete all as specified and as directed

S&F water heater (Geyser) storage type 25 ltr, suitable for working on single phase 240 volt, AC supply, 5 Star rated, 2KW with fixing nuts and bolts complete with cold and hot connecting pipes complete all as specified and as directed.

S&F 25 Watt LED outdoor new generation, post-top, energy saving, environmental friendly, long life aesthetically disigned with symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs as light source with IP 65 protection including taking down old unserviceable light complete all as specified and as directed.

S&F 25 Watt LED, IP66, 230V environmental friendly with operating temperature -10 to 50 degree celsius, operating voltage range 140 to 270 Volts, system lumen 2500, colour temperature 5700K suitable for pole dia 43 mm (Max) including GI pipe bend, bracked and accessories complete all as specified and as directed.

S&F modular type RJ-11 telephone socket outlet with shutter fixed on modular MS/GI sheet box and cover plate (paid seperately) including connections etc complete all as specified and as directed.

S&F cover plate with frame single module for modular metal flush box complete all as specified and as directed.

S&F modular metal (MS/GI) flush boox single module fixed flush to wall and making good to the disturbed surfaces of wall/floor and matching with existing specifications complete all as specified and as directed.

M&L for rigid non metallic PVC conduit medium grade exclusive of terminal boxes but inclusive of all tees, reducers, bellmouth tube ends, junction boxes and fixing accessories such as couplers, lock nuts, saddles pipe hooks etc. for size 25mm dia for telephone wire/TV cable complete all as specified and as directed.

All as per Srl item No. 4.50 here-in-before but dia 20mm complete all as specified and as directed.

S&F telephone wire 2 pair, 0.5 Sqmm PVC insulated unurmoured drawn into existing conduit including connecting complete all as specified and as directed.

S&F modular type TV CO-axial Socket-1 module complete all as specified and as directed.

S&F calling bell ding dong type complete all as specified and as directed.

EXTERNAL ELECTRIC SUPPLY

Labour only for boring road or path horizontally for crossing of cable of size 80 mm complete all as specified and as directed.

Supply and fix GI pipe of dia 50 mm to wall/pole/ buried under ground of medium grade with required clamping arrangements to fix with the pole or buried underground complete all as specified and as directed.

Supply and fix GI pipe of dia 25 mm to wall/pole/ buried under ground of medium grade with required clamping arrangements to fix with the pole or buried underground complete all as specified and as directed.

Taking down ol unserviceable cable from pole any size and removing from site complete all as specified and directed.

Supply, laying, testing and commissioning XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade cross section area 4 Sqmm 4 core in trenches / fixing on wall by saddle/ fixingn on pole/drawn through GI pipe complete all as specified and as directed.

Supply, laying, testing and commissioning XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade cross section area 35 Sqmm 4 core in trenches / fixing on wall by saddle/ fixing on pole/drawn through GI pipe complete all as specified and as directed.

M&L for sub class 'B' brick for protection of UG cable in trenches of old size brick complete all as specified and as directed.

EXTERNAL WATER SUPPLY

Takingdown / taking out of damaged GI pipes of 25 mm dia from wall/trenchs includig all fittings and fuixtures and removing from site complete all as specified and as directed.

Supply and laying in trenches / fix to wall 32 mm dia 3-layer PP-R (Polypropylene random copolymer) pipes SDR 7.4 & SDR 11 UV stabilized and antimicrobial welded havingthermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropelene random fittings fixed complete to walls, ceilings or in floors etc with reducer, bends, elbows, union etc complete and connecting to the existing pipe line complete all as specified and as directed.

S&F PPR gate valves of 32 mm including taking down the old unserviceable gate valve completed all as specified and as directed.

Supply and fix in repair Ball brass valves, bearing ISI mark high pressure, with polythene float and fly nut complete including connection with existing iron pipe and brass ferrule wih necessary fittings for iron pipe of 25 mm dia complete all as specified and as directed.

Taking down old unserviceable polythene tank of any type, any size complete including all its accessories and removing from site complete all as specified and as directed.

S&F multi layered Rotational moulded polyethylene water storage tanks 1000 ltrs (Cylindrical vertical with closed top) hoisted andfixed in position all as specified and as directed.

S&F multi layered Rotational moulded polyethylene water storage tanks 500 ltrs (Cylindrical vertical with closed top) hoisted andfixed in position all as specified and as directed.

M/s CHAFIANG ARAN

M/s DEBOJIT ROY

THE BUILDERS