SPECIAL REPAIRS TO BLDG NO. P-26, P-29 AND P-30 (JCOs/ MD ACCN) AT LOKHART LINES AND PROVN OF BOUNDARY WALL NEAR STN HQ CELL UNDER GE (WEST) BAREILLY.

Amount

B/R Portion

Dismantling of Asbestos cement corrugated or semi corrugated etc sheets in roof covering complete all as specified and directed.

S&F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering/clading to wall, fixed with self tapping screws complete all as specified and directed.

S&F pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in ridges, roof covering/clading to wall, fixed with self tapping screws complete all as specified and directed.

Dismantling fillets, rails, post, rafters, purlins, etc under 40 Sqcm in section in any position unframed work. complete all as specified and directed

Dismantling timber scantlings 40 sqcm & over in section , in any position unframed work/ truss etc complete all as specified and directed

S & F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed

S & F in repairs 4mm thick E-Board tiles for insulation and acoustic purpose of size 600x 600mm fixed with and including anodised GI prepainted snap grid with 25x25x1.5 mm thick Tee section and 38x25x2 mm thick angle with hanging/supporting arrangements as in false ceiling at bottom at spacing 60 cm centre to centre including necessary GI cleats and 4mm dia GI wire as suspender fixed to ceiling not exceeding 1.20 mtr centre both ways with dash fastners complete and making good disturbed surfaces complete all as specified and directed.

M & L for non-skid ceremic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match of tiles and screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6 for laying floor finishes including dismanlting/demolition of existing flooring all as specified.

All as per serial item No 9 as above but as in vertical surfaces of tiles and rendering 10 mm thick in cement mortar 1:4, including dismantling as in backing layer complete all as specified.

M & L for non- skid ceremic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match incl dismantling of tiles and screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6 for laying floor finishes all as specified and directed.

M & L for colour glazed ceremic coloured tiles in vertical surface300x450 x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thick screed bed or bedding layer of cement mortar 1:4 cement and dismantling of wall tile including cement mortar bedding complete all as specified.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons Laid, bedded and pointed in any mortar etc as specified and directed.

M&L for 20 mm thick granite (of any type and shade) work (table rubbed and polished) in floors, steps, jambs, pillars, window cills, cooking plateforms and like in CM 1:4 incl pointing in white cement(1:2) using marble dust with admixture of pigment to match the shade of granite stone including grinding and polishing, moulding of edges complete over and incl 20 mm thick screed bed or bedding layer of mortar in cement mortar 1:4 complete incuding hole for gas pipe complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar or cement lime mortar including all quoins, aches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles all as spd and directed

M&L Brickwork old size with subclass ‘B’ bricks, except brick straight or curved on plan exc 6m mean radius built in in CM (1:6) complete all as specified and directed.

M&L Brick work with fly ash bricks ,old size brick straight or curved on plan exceeding 6 M mean radius built in CM 1:6 complete all as specified and directed

M&L brick work with fly ash bricks straight or curved on plan to any radius in half brick thick walls built in cm (1:4) all as spd and directed

Taking down cement plaster from wall of any description including terrazzo tiles, skirting/dado on brick or stone walls etc including raking out joints, hacking for key and scrubbing down with water etc.all as specified and directed.

M&L 15mm thick cement plaster on fare faces of brick or concrete surfaces in CM 1:4 including using of WPC as per manufacturer instruction of cement including finishing the surface even and smooth without using extra cement complete all as specified and directed. Note:- WPC Shall be measured and paid seperately.

M&L 15mm thick cement plaster on brick surfaces or concrete surfaces in cm 1:6 on other than fair faces of brick work, finished even and smooth without using extra cement complete all as spd and directed

Supply only liquid waterproofing compound all as specified.

M&L for applying one layer of wall care putty on wall surfaces incl rubbing down the surfaces with sand paper after getting dried all as directed to obtain a smooth & even surface complete all as spd and directed.

M & L applying two coat of distemper oil emulsion white or tinted on newly decorated or undecorated wall surface including preparation of surfaces by washing rubbing down and stoping of any surfaces of walls complete all as specified.

M & L applying two coat of distemper oil emulsion white or tinted on old decorated or undecorated wall surface including preparation of surfaces by washing rubbing down and stoping of distempered and painted surfaces complete all as specified.

M & L applying two coat of cement based paint on old decorated or undecorated wall, roof surface including preparation of surfaces by washing rubbing down and stoping of old wall surfaces complete all as specified.

M&L white washing two coats on wall surfaces including preparation of newly plastered untreated surfaces and necessary scaffolding all as spd and directed

M&L for prepration of newly plastred surfaces of wall and applying two coat of cement base paint complete all as specified and directed.

M&L for applying two coat of exterior weather proof 100% anti fungal acrylic smooth emulsion with silicon additives that offer anti algae high performance exterior wall finish on old wall surfaces complete all as specified and directed.

M & L for plain cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) as in plinth protection 75 mm thick finished even and fair including forming 10 mm wide joints at not exceeding 3 m distance between adjoining slabs shall not exceed 10 mm in thickness and shall be filled with bitumen mastic i.e. bitumen and sand in proportion 1:2 including demolition of existing surface all as specified or as directed.

Taking down of chowkats or frames n.exc 1.5 Sqm each with shutters (without taking of shutters from the frames) complete all as specified.

Taking down of chowkats or frames exc 1.5 Sqm but n exc 4 sqm each with shutters (without taking of shutters from the frames) complete all as specified

S&F for 125x60mmx1.25mm thick pressed steel, frames for door with one or more rebates including filing and inner surface of the frame shall be treated with a coat of bituminous paint & compaction with PCC 1:3:6 Type C1, necessary fixing lugs, SS hinges, lock strike plate, 02 x MS bar/flat at bottom of the frame etc, complete including wooden texture finished paint on the frame surface all as specified and directed.

S&F for 105x60mmx1.25mm thick pressed steel, frames for door with one or more rebates including filing and inner surface of the frame shall be treated with a coat of bituminous paint & compaction with PCC 1:3:6 Type C1 necessary fixing lugs, SS hinges,lock strike plate, 02 x MS bar/flat at bottom of the frameetc, including wooden texture finished paint on the frame surfacecomplete all as spd and directed.

S&F for 35 mm thick Factory made flush shutter, solid core construction with block board core and ply wood face panels, commercial type on both side, complete all as specsified & directed.

S & F factory made 35 mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

M & L for 35mm thick Factory made plain framed glazed and skeleton shutter open rebated & prepared to receive glass, gauge etc, with sash bar edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass including campsule mesh tightly fixed with the glazed and skelton door shutter etc, of 2nd class hard wood, members of shutters as specified in SSR Part - I Section 8 clause 8.24 (a) fitted to chowkats all as specified and directed. Note:- Wiremesh will be measured and paid separately.

Supply and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame complete as specified by the manufacturer and as per directions of Engineer-in-charge.

Supply and fixing 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table 3 of IS: 14856 complete all as specified by the manufacturer and as per directions of Engineer- in-charge.

S&F for 100mm long stainless steel butt hinges complete all as specified and directed.

S&F for 150mm long aluminum handles, cast type complete all as specified and directed.

S&F for 150mm long aluminum anodised, barrel tower bolts of extruded section and fixed.

S&F 200mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast all as spd and directed.

S&F 150 mm long floor door stopper of aluminium alloy body and tongue, brass body and tongue with hard drawn steel spring fixed in floor complete all as specified and directed.

M & L for painting to new wood and wooden based surfaces of any description exc. 10 cm width or girth with two coats of synthetic enamel paint over a coat of pink primer including prepration of new wooden surfaces all as specified or as directed.

M&L for painting to steel surface exc 10 cm width or girth with two coats of synethic enamel paint over a coat of red oxide primer including preparation of newly pained surface all as spd and directed

S & F 300 mm size, MS ordinary rat tail rod pattern springs including roller and roller plate if fixed to chowkats with flat iron 40x3mm size 75cm long with necessary bolts, etc complete all as specified and directed

S&F Mild steel bands, straps, supports or stay, for rain water, ventilating pipes including bolts if reqd, hooks (stay) heavy for large gates hook and pintle large hasps and staple, chains hand made sliding bolts clamps, hold fasts wall ties etc etc hooks for hanging fans plain angle cleats for securing purlins to wood truss or rafter, knee piece inserts, two way and three way straps, plate washer and similar small articles confirming to Fe-290 Gde - E-165 all as spd and directed

S&F sheet glass of 4mm,ordinary quality and glazing with oil putty or wooden beading in squares n.exc 0.5 Sqm in each pane,complete all as specified.

S&F galvanised mild steel wire cloth 0..56mm nominal dia of wire and average width of aperture 1.18 mm all as spd and directed

S&F for steel ventilators with top fixed type, with glazing bars complete welded including one shop coat of Red Oxide Zinc chromate primer complete all as specified and directed (Note :- Glass shall be measured and paid for separately).

S&F of Steel windows with pressed steel frame ( size 95x45x1.25mm) side hung shutter including box type hinges with steel handle, and steel peg steel complete with glazed openable shutter with glazing bar (open out side) and wire gauged openable shutter without glazing bar ( open in side) dovetailed or welded complete all as specified and directed and all as per Drg No TD/088 dt 07 jan 2002 Note:- (i) Two shutter ie wire gauged and glazed shall be fixed in one composite frame and both shutter shall be measured as one unit. (ii) Rate for filling of PCC in frame deemed to be included in quoted rate. (ii) MS grill shall be measured and paid seperatly under relevant item of schedule

S&F mild steel framed work as in window guard bars, grills or forged into spikes, framed balusters, walkway railing etc and similar work including welding complete FE-290 grade E-165 all as specified and directed.

S&F for 15mm bore galvanised steel water tubing with all fittings 'medium grade' and fixed complete to wall and ceiling or laid in floors including taking down of GI tubing complete all as specified or as directed.

S&F for 20mm bore galvanised steel water tubing with all fittings 'medium grade' and fixed complete to wall and ceiling or laid in floors including taking down of GI tubing complete all as specified or as directed.

S&F in repair 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified or as directed.

S & F 500 ltrs capacity rotational moulded polythylene triple layered water storage tanks white in colour (cylindrical vertical with closed top) hoisted and fixed in position including taking down old water tank complete all as specified and directed.

S&F 15mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed (Minimum weight 210 gms complete all as specified or as directed.

S&F in repairs Vitreous China table/counter top wash basin of suitable size including SS bottle trap, and cabinet of PVC shutter fixing on counter with SS waste coupling complete all as specified and as directed. Model : Cat No 91072 Orchid of Hindware , Cera Cat Part No 2030104, Kerovit Cat part No :- KB2243 & Asian Paints cat part No :-TT-53-X

S&F in repairs Vitreous chinaware coloured wash hand basin with padestal of size 55X40X82cm complete including CP Waste coupling ,waste pipe ,complete fixing arrangement and cutting for and pinning in walls & making good complete all as specifed and directed by Eng in charge. Model :- Jaquar Cat Part No:- FNS-WHT-40801 for WHB & FNS-WHT-430301 for pedesal, Cera cat part No S2040104 for WHB & S2090101 For pedestal, Kerovit Cat Part No K0284W for WHB & KO314W for pedestal, Hindware cat No 10082 & Asian Paints Cat part No WM-24-X for WHB & FP-24-X for Pedestal.

S&F in repairs Vitreous china wash down water closet EWC) white semi-pedestal pattern complete, including connection to drain pipe and to flushing pipe antisyphonage pipe plastic water closet seat back closed pattern with flat bottom cover and mild steel chromium plated or aluminized hinging device, incl. jet connections etc complete all as spd & directed

S&F in repairs vitreous china squatting pan of orrissa pattern long pan size 580 x 440 mm white with "P"or "S" trap size 100 mm dia front or back inlet and integral foot rest any pattern (excluding flushing cistern and flush pipe) including provn of lime concrete bedding (1:2:5), minimum 150mm all round and finish just below level of rim of pan complete all as specified and directed.

S&F in repairs PVC low level flushing cistern 10 litres, valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, flushing pipe complete all as specified and directed. Model :- Sleek fresh dual flush of Hindware Model No Pastel size 47.6x15.5x32 , Parryware Cat No 8177*, Cera Cat No B1810110 fittings snow white

S&F fancy type brass chromium plated toilet paper holder, including taking down PTMT Toilet Paper Holeder complete all as specified and as directed. Model No :- ACN-1153N Jaquar, Hindware model No F 880003, Parryware model No T6514A1 & Asian Paints Cat Part No AC506B.

S&F health faucet 1 mtr SS Braided connection tube with wall hook complete for EWC incl necessary fitting including taking down PTMT health faucet complete all as specified and directed. Make : Jquare Cat Part No ALD-CHR-577, Cera Cat No :- F803008AB, Asian Paints Cat Part No C-232N & Kerovit Cat No KA580008

S & F fancy type 150mm size square brass CP shower rose with or without swivel joints including taking down existing PTMT fitting complete all as specified and as directed. Model No: Cat No. F 7010505AB of Cera , Hindware Model Cat No F 16062 , Asian Paints Cat Part No RF 208 & Kerovit Car Part No KA570018

S&F brass chromium plated wall mixer 3 in 1, 15mm for mixing hot & cold water screwd down three joints to steel pipes or unions and plugging and screwed to walls incl necessary fitting including taking down existing PTMT fitting complete all as specified and as directed. Model : Model of Hindware Cat No F390022, Cera Cat Part No :- F1012403, Kerovit Cat Part No KB511018 & Asian Paints Cat Part No ALWM104.

S&F fancy type 15mm dia chromium plated fancy type wall mixer hot & cold with long swan for kitchen sink fixing and connection to pipes incl necessary fitting including taking down existing PTMT fitting complete all as specified and as directed. Model :- Cera cat Part No:-1016501 ,Kerovit Cat Part No KB411019 & Asian Paints Cat Part No SYSM101.

S&F brass chromium plated tubular towel ring including a pair of CP brass bracket complete & necessary fitting including taking down existing PTMT fitting all as specified and directed. Model No:- Cera Model No F5002105, Asian Paints Cat Part No SQTW 201 & Kerovit Cat Part No KA670005

S&F tubular, towel rail brass chromium plated 25mm dia D type 60 cm long between flanges including taking down existing PTMT fitting complete all as specified and directed

S&F in repairs fancy type brass chromium plated soap dish of 160x160x90 mm complete all as specified and directed.

S & F in repairs fancy type sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with CP bracket gaurd and railling 60 cm long complete all as specified and directed. Model: model No F-5005301 of CERA, Asian Paints Cat Part No AC107 & Kerovit Cat Part No :- KA920005

S&F fancy type 15 mm bore brass chromium plated WHB mixer for mixing hot and cold water screwed down for iron pipe and fixed to WHB including taking down existing PTMT fitting complete all as specified and directed. Model :ARI 39001B Aria of Jaquar ,Hindware Model No F280010 SCP, Cera Model No F2002461, Asian Paints Cat Part No MMCH101 & Kerovit Cat Part No :- KB1211026.

S&F fancy type chromium plated brass angle valve type suitable for 15mm bore pipe including taking down existing PTMT fitting complete all as specified and directed. Model : Hindware Model No F320006, CERA Cat No :- F1017201, Kerovit Cat part No :- KA910007 & Asian Paints Cat Part No MAAC101N.

S&F 15 mm dia bib tap fancy type chromium plated with flange quarter turn incl all necessary fittings including taking down existing PTMT fitting complete all as specified and directed. Model : Cera model No F1014151, Kerovit Cat Part No KB 2111004, Asian Paints Cat Part No MABC101.

S&F in repairs 450mm long PVC connection 15mm bore with PTMT nuts specified and directed.

S&F in repairs sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm etc complete all as specified and as directed . Model :- Cera Cat No B 4711501- satin finish series alma, Kaff Cat No KS610SB (R10) Marco series, Hindware Cat Part No 512451, Asian Paints Cat Part No SG24188.

S & F stainless steel plate rack not less than 5 Kg of size 31"X36"X10" complete all as specified and as directed.

S&F in repairs 100mmx100mm stainless steel grating fixed complete all as specified and directed.

S/F in repairs low density polyethene pipes (LDPE) 32mm of pressure rating 6 Kg/cm2 fixed to walls or laying in floor etc complete all as specified and directed.

S&F in repairs 20 mm dia Stainless Steel fancy type drapery curtain rod with brackets and lattu & other connected accessories etc complete all as specified and directed.

Taking up or down AC/PVC/SWG rain water pipe, soil/waste/vent pipe of any size with fittings etc. complete all as specified and directed.

S & F PVC (SWR) 110 mm dia soil waste or rainwater drainage pipes single socketed in any length with rubber ring joint laid in floor or fixed on wall all as specified or as directed.

S & F in repairs PVC (SWR) 110 mm bore bends all as specified or as directed.

S & F in repairs PVC (SWR) 75 mm bore bends all as specified or as directed.

S & F PVC (SWR) 75 mm dia soil waste or rainwater drainage pipes single socketed in any length with rubber ring joint laid in floor or fixed on wall all as specified or as directed.

S&F PVC in repairs (SWR) vent cowl 75 mm dia as specified and directed

PVC (SWR) in repairs gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

M & L in repairs for PVC (SWR) floor trap/Nahani Trap, dia of outlet 75mm, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F aluminium power coated(colour) section for Cabinet shutter in Kitchen, glazed with aluminium shutter weighting 0.55 kg/m including necessary fitting of suitable size, one or more rebate,cut to jointed together with cadmium plated steel screws including rubber bending or gasket for aluminium sections for fixing glass/Xpm jalli and necessary fittingd,screws, plugs for fixing screws, etc complete all as specified and directed

S&F powder coated aluminium frame for windows, ventilators and kitchen cupboards frame etc size 100x44mm and 1.2mm thick /requisite size thick with one or more rebates including joining cleat for fixing etc and add for powder coating (minimum thickness of powder coating 50 micron) complete all as specified.

Demolition of cement concrete (unrinforced), in ground floor and paving n.exc. 15 cm thickness( below or above ground level) including tile/ terrazzo floor complete all as specified and directed.

M&L for cement concrete type D2 1:4:8 (40 mm graded aggregate) as in mass concrete, foundation, filling complete all as specified and directed.

M&L 25mm thick cement concrete type B1 1:2:4 using 12.5mm graded stone aggregate in floor finishes even and rough to receive floor tiles complete all as specified and directed.

M & L 75mm thick plain cement concrete type D-2 1:4:8 (40 mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L for (400x400)mm ( 10 to 12 mm thick ) out door vetrified designer anti skid coloured tiles including designer borders tiles (Square/ rectangular) in floors/path/hard standing etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15mm thick screed bed in cm-1:6 complete all as specified and directed.

M & L for Plain Cement Concrete 1:2:4 in surface chanel, drain work and coping etc complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M & L formwork to sides and soffits of lintels,lintel bend, beams etc finished rough surfaces of concrete complete all as specified.

M & L formwork to chullah hoods, chajjas, trough and similar items including edges finished rough surfaces of concrete complete all as specified.

M&L mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 5 mm dia and over up to and including 10 mm dia as in stirrups, spacer and binders, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L RCC 1:2:4 type B1 using 20 mm graded aggregate as in slab, shelves and stair case etc.all as specified and directed.

M&L RCC type B 1, 1:2:4 (20mm graded agg) as in beams, cantilevers, lintels, complete all as specified and directed.

M&L RCC 1:2:4 type B1 using 20 mm graded aggregate as in chajjas and like all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft and loose Soil complete all as specified and directed.

Removing excavated soil n.exc 50mtr and depositing where directed at a level n exc 150 mtr above the starting point. complete all as specified and directed.

Returning filling in, including spreading, levelling, watering and well ramming in layers n exc 25cm in soil. complete all as specified and directed.

Excavating in post holes in soft and loose soil (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm,complete all as specified and directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground in natural ground complete all as specified and directed

M&L Cutting into existing manholes for connecting new drains, making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 sectiion) in cement concrete 1:2:4 (type B1) smooth finished, and reforming benching as required of pipe 150mm dia complete all as specified and directed.

M&L for 150 mm dia Reinforced concrete pipes, class NP2, laid and jointed complete with collars laid in trenches and jointes including concrete bed to drain 150 mm bore NP-2 pipe, in plain Cement concrete 1:3:6 type C-1 (using 20 mm graded stone aggregate) including packing under, and haunching against the sides of pipes after they are laid and tested including dismantling of existing pipe complete complete all as specified and directed.

M & L for precast reinforced concrete 1:2:4 type B1 using 20 mm graded stone aggregate for cover slab set in and pointed in CM 1:6 including necessary formwork, and demolition of existing slab complete all as specified and directed.

Internal E/M Portion

Taking down carefully aluminium point wiring any type including battens if any except for ceiling or where not feasible for light/ fan//bell/socket or power and including unscrewing from board, fitting and fixture such as switches,socket, ceiling rose,lamp holder,pendants, bracket and regulator etc and removing material from site including making good disturbed surface to match with the existing surface complete all as specified.

Taking down carefully UNSV main switch DBs of any description of an size in any position complete all as specified.

Taking down submain wiring including all accessories complete all as specified and directed.

Material and labour for point wiring with single core FRLS 1100 volt grade cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium duty ISI marked not less than 20mm dia, with all conduit accessories, screws (concealed conduit wiring in walls and casing capping on ceiling or roof) including metal box suitable for modular fittings and covered with modular plate and cover of suitable size with new brass screws for mounting switch sockets and regulators and drawing continuous earth wire with and including PVC sheathed 1100 Volts grade cable with stranded copper conductor of size 1.5 Sq mm (Nominal area) and connected to main earth dolly complete all as specified for:- (a) One light / fan/ exhaust fan point controlled by one switch.

All as per srl Item No 120 above but (b) One 5 pin 5 Amp switch socket out let point on an independent board.

All as per srl Item No 120 above but (c) One 5 pin 5 Amp socket out let point controlled by one switch on same board.

All as per srl Item No 120 above but (d) One buzzer/ bell point controlled by one push button on the same board with other switches or independent

All as per item 120 here in before but for one 15 Amp 6 Pin switch socket out let independent with 2.5 Sqmm FRLS (Nominal Area) PVC unsheathed copper conductor single core multistranded incl 2.5 sq mm FRLS PVC copper conductor single core used as earth continuity conductor complete all as specified.

S & F Modular switch one way 10 A, 1 Module complete all as specified and directed by the Engr-in-Charge.

S & F Modular switch one way 16 A, 1 Module complete all as specified and directed by the Engr-in-Charge.

S & F Modular bell push 6 Amp, 1 Module complete all as specified and directed by the Engr-in-Charge.

S & F Modular Socket 6 Amp, 2/3 Pin combined 2 Module complete all as specified and directed by the Engr-in-Charge.

S & F Modular Socket 6/16 Amp, 2/3 Pin combined 2 Module complete all as specified and directed by the Engr-in-Charge.

S & F in replacement Modular fan regulator in repairs Step up type, 120 Watt, 2 Module complete all as specified and directed by the Engr-in-Charge.

Supply and Fixing in replacement ceiling rose in repairs PVC / Poly carbonate, Isolated body, three terminal AC 230 volts complete all as specified and directed.

M & L for replacement of lamp holder, PVC / Poly carbonate, insulated body modular type with back plate batten/angle type for batten fittings complete all as specified and & directed

S&F in replacement LED mirror light fitting of 1 x 10 watt LED batten with aluminium housing with all accessories prewired suitable for wall /surface mounting complete with connection all as specified and directed.

S&F, in repairs, LED light fitting, high lumens batten type, housed in extruded from powder coated aluminium, 20 watt for soft diffuser lighting with and including lamp and connecting up complete with white PVC insulated and PVC sheathed round flexible three core copper conductor cable of suitable size and testing on completion all as specified and directed.

S&F in repairs indoor decorative LED City-3 light fitting suitable for & including single 12 Watt LED lamp with polycarbonate body with upper globe complete all as specified and directed.

Supply and Fix in repairs LED lamp 12 Watt, 230 V , AC integrated circuit complete all as specified and directed.

Supply and fixing in repairs Buzzer, Ding Dong AC. 230 volts,single pole complete all as specified and directed.

Supply and Fix in repair LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. for fixing in wall of suitable size and length of bracket not less than 1.2 mtr complete all as specified and directed. Note:-Cost of bracket,clamps and nut bolts included in quoted rate.

M&L for sub main wiring with 2 single core 4 Sqmm (FRLS) copper conductor PVC unsheathed cable medium grade including PVC conduit (appropriate size) concealed in wall for sub main connection including 4 Sqmm (FRLS) PVC insulated multistranded unsheathed copper conductor used as a earth wire to common earth and connection to earth dolly all as specified. ( Note :- Two runs of 4 sqmm (FRLS) and one run of 4 sqmm (FRLS) copper conductor shall be measured as one unit length.)

Supply and fixing ceiling fans complete with blades, down rods, and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) and old fans deposited to MES yard complete all as specified and directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and directed.

Supply and fix Water heater storage type, electric,capacity 25 litres.BEE 5 star rated complete all as specified and directed.

Supply and fix flush sheet metal enclosure SPN DB 12 way with double door IP-42 protection detachable gland plates, flush mounting for MCB fitted with bus bar , earth bar and neutral links complete all as specified and directed.

S&F in repairs MCB SPN 40 Amp 240 volt complete all as specified and directed by the Engr-in-Charge.

S&F in repairs MCB single pole 6 to 32 Amp 240 Volt 'B' curve 10 KA complete all as specified and directed by the Engr-in-Charge.

S & F in repairs Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps complete all as specified and directed.

Material & Labour for earthing complete including taking out old unsv and replace with galvanised steel earth plate 600x600x 6mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 meters below normal ground level, surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate using 4 mm dia GI wire as earth wire electrode moulded and rivetted to earth plate at one end and connected to main switch/ control switches of buildings at another end, GI earth wire encased in and including 15 mm dia GI 'light grade' pipe from upper end of earth plate upto main switch board of building including 20 dia bore GI pipe 'light grade' as water pipe from earth chamber and including excavation and earth work, PCC 1:3:6 type C1 chamber and MS angle iron frame 40x40x3mm and RCC cover 40mm thick (1:2:4) type B1 using 20mm graded stone aggregate reinforced complete all as specified and directed.

Taking down carefully electric/electronic meter and deposited in MES yard complete all as specified and directed.

External E/M Portion

Supply and laying & testing UG cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (Heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm,2 core. complete all as specified and directed.

M&L for sand cushioning laid in trenches for laying of LT UG cables complete all as specified and directed.

M&L Modular bricks common burnt clay building bricks, sub-class ‘B’ designation-75 for LT UG cable protection complete all as specified and directed.

S&F GI tubes light grade of dia 80 mm with all fitting and fixed complete for protection of LT UG Cables laid to walls or in floors or along with poles etc complete all as specified and directed.

Taking down carefully service connections of any description from pole, wall or service brackets etc including making good disturbed surface to match with the existing surface complete all as specified.

Boundary Wall Portion

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft / loose soil complete all as specified and directed.

M & L for rendering 15 mm thick cement plaster on other than fair faces of brick work or stone masonry surfaces with cement mortar 1:4 finished even and smooth complete all as specified and directed.

M & L for rendering 15 mm thick cement plaster on fair faces of brick work or stone masonry surfaces with cement mortar 1:4 finished even and smooth complete all as specified and directed.

M & L for preparing newly plastered or previously untreated wall surfaces and applying two coats of cement base paint over one coat of primer complete all as specified and directed.

M & L for use and waste of form work to sides of pillars, posts, struts, piers, columns and stanchions in rough finished surface of concrete complete all as specified and directed.

M & L for providing reinforced cement concrete 1:2:4 (Nominal Mix) type B-0, using 12.5 mm graded stone aggregate as in foundation including rafts, footing, foundation beams, plinth beams, base of columns and the like complete all as specified and directed.

M & L for providing reinforced cement concrete 1:2:4 (Nominal Mix) type B-1, using 20 mm graded stone aggregate, as in beams, cantilevers, bressummers, lintels over 1.50 m span and the like complete all as specified and directed.

M & L for use and waste of form work to sides of concrete foundation, footing, bases of columns, raft & raft beams, sides and soffits (if any) of foundation and plinth beam and similar works in rough finished flat surface of concrete complete all as specified and directed.

M & L for providing reinforced cement concrete 1:2:4 (Nominal Mix) type B-1, using 20 mm graded stone aggregate, as in columns, pillars, piers, posts, struts and the like complete all as specified and directed.

S & F of rolled mild steel joist, channel, angle, flat iron or Tee sections, fixed independently without connecting plates etc. (cut to ordinary length indicated posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, wind ties, etc flat iron fillets (for securing wire mesh) including all necessary drilling, bolting or riveting etc and similar work ) confirming to Fe-290 Grade E-165 complete all as specified

S & F of rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc. confirming to Fe-410-W (Grade E-250) Quality 'B', drilled for fixing of steel sheeting or other covering doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fitting and also fastening complete all as specified and directed.

S & F razor wire 2.24mm dia with 20mm wide and 0.5mm thick razor strip fixed with clamps in rows and angle iron bracket / frame over boundary wall etc complete all as specified and directed. Note:- Angle iron frame / bracket shall be measured and paid seperately.

S & F diamond shape high strength steel punched tape concertina coil 600mm dia (in specific stetched position) hot dip galvanised coated with CLR anti corrosive paint by making diamond shape with the help of dove tail clips (18 SWG) fixed over razor with the help of hog rings (14 SWG) in angle iron bracket / frame over boundary wall complete all as specified and directed. Note:- Each Razor Wwire and Angle iron frame / bracket shall be measured and paid seperately.

Notes:- Tenderers may note that amount as given in schedule of credit will be deducted from the total amount to worked out the net contract sum at the time of Acceptance of tender.

REHAN CONSTRUCTIONS (BID ID -3406615)

RIYASAT ALI KHAN (BID ID -3406009)

M J ENTERPRISES (BID ID -3412233)

madhur buildtech (BID ID -3411150)

M/S SATISH KUMAR JAIN (BID ID -3405763)

M/S Alam Construction Co (BID ID -3404909)

Devout Tech Solutions (BID ID -3405851)

M/S Shree Sai Builders (BID ID -3405172)

novell engineers (BID ID -3404968)

M/S Harshri Nath Enterprises (BID ID -3405646)