PM-ABHIM

Construction of Building Ground Floor

Earth work excavation for foundations (Manual Means) of buildings, septic tank, sump, compound wall in ordinary soils and depositing on bank with an initial lead of 10m and depth up to 3m including all operational, incidental, labour charges such as shoring, sheeting, planking, strutting etc., and including over head charges & contractor profit, but excluding GST & Seigniorage charges etc., complete for finished item of work excluding dewatering charges etc., as per SS 20 B(APSS 308)

Filling with Stone Dust in trenches,sides of foundations and basement with initial lead in layers not exceeding 15cm thick,watering and ramming including cost and conveyance of water to work site and all operaitonal,incidental, labour charges,hire charges of T&P etc., and including over head charges & contractor profit, but excluding GST & Seigniorage charges etc., complete for fnished item of work(APSS NO.309&310)

Plain Cement Concrete (1:4:8) (cement: fine aggregate: Coarse aggregate) for foundations using coarse aggregate 40mm size hard , machine crushed granite from approved quarry using concrete Mixer 10 / 7 cft (0.2 / 0.8 cum) capacity including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site including all charges for machine mixing and hire charges of concrete mixer, laying concrete in foundations and under flooring bed, ramming in 15 cm layers finishing top surface to the required level curing etc., and including over head charges & contractor profit, but excluding GST & Seigniorage charges etc., complete, for finished item of work. (APSS No. 402) Bed Concrete for Footings & for flooring

Supply and placing of the Design Mix Concrete M 25 grade corresponding to IS 456 with cement content of 380 kgs per 1 cum of concrete using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate - as per IS 383 - 1970 and IS 2386 Part 1 to Part 8) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site, centering using steel scaffolding pipes , jack props , wallers , foot plates , brackets , steel centering plates etc., including all operational, incidental and labour charges such as weigh batching, machine mixing, lifting of concrete manually, laying concrete, vibrating, curing etc., and including over head charges & contractor profit, but excluding GST & Seigniorage charges etc., complete, but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402) For Footings

Supply and placing of the Design Mix Concrete M 25 grade corresponding to IS 456 with cement content of 380 kgs per 1 cum of concrete using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate - as per IS 383 - 1970 and IS 2386 Part 1 to Part 8) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site, centering using steel scaffolding pipes , jack props , wallers , foot plates , brackets , steel centering plates etc., including all operational, incidental and labour charges such as weigh batching, machine mixing, lifting of concrete manually, laying concrete, vibrating, curing etc., and including over head charges & contractor profit but excluding GST & Seigniorage charges etc., complete, but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402) for Pedestals

Supply and placing of the Design Mix Concrete M 25 grade corresponding to IS 456 with cement content of 380 kgs per 1 cum of concrete using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate - as per IS 383 - 1970 and IS 2386 Part 1 to Part 8) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site, centering using steel scaffolding pipes , jack props , wallers , foot plates , brackets , steel centering plates etc., including all operational, incidental and labour charges such as weigh batching, machine mixing, lifting of concrete manually, laying concrete, vibrating, curing etc., and including over head charges & contractor profit but excluding GST & Seigniorage charges etc., complete, but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402) for columns

Supply and placing of the Design Mix Concrete M 25 grade corresponding to IS 456 with cement content of 380 kgs per 1 cum of concrete using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate - as per IS 383 - 1970 and IS 2386 Part 1 to Part 8) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site, centering using steel scaffolding pipes , jack props , wallers , foot plates , brackets , steel centering plates etc., including all operational, incidental and labour charges such as weigh batching, machine mixing, lifting of concrete manually, laying concrete, vibrating, curing etc., and including over head charges & contractor profit, but excluding GST & Seigniorage charges etc., complete, but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402) for Plinth beam

Brick masonry walls in superstructure with CM (1:6) prop: (Cement : Sand) using common burnt clay bricks of class as per Table- I of IS:1077-1992, Non- Modular or traditional size 23 x 11 x 7 cms from approved source having minimum crushing strength of 40 Kg/Sqcm. including cost and conveyance of all materials like cement, screened sand, bricks, water etc., to site, labour charges, like mixing cement mortar, constructing masonry, lift charges, curing, etc.,and including over head charges contractor profit but excluding GST & Seigniorage charges etc..complete for finished item of work. (APSS No. 501 & 504) for Basement

Plain Cement Concrete (1:5:10) (cement: fine aggregate: Coarse aggregate) for foundations using coarse aggregate 40mm size hard , machine crushed granite from approved quarry using concrete Mixer 10 / 7 cft (0.2 / 0.8 cum) capacity including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site including all charges for machine mixing and hire charges of concrete mixer, laying concrete in foundations and under flooring bed, ramming in 15 cm layers finishing top surface to the required level curing etc., and including over head charges & contractor profit, but excluding GST & Seigniorage charges etc., complete, for finished item of work. (APSS No. 402) Bed Concrete for flooring

Brick masonry walls in superstructure with CM (1:8) prop: (Cement : Sand) using common burnt clay bricks of class as per Table- I of IS:1077-1992, Non- Modular or traditional size 23 x 11 x 7 cms from approved source having minimum crushing strength of 40 Kg/Sqcm. including cost and conveyance of all materials like cement, screened sand, bricks, water etc., to site, labour charges, like mixing cement mortar, scaffolding charges, constructing masonry, lift charges, curing, etc.,and including over head charges contractor profit but excluding GST & Seigniorage charges etc..complete for finished item of work. (APSS No. 501 & 504) for Super Structure

Reinforced Brick Masonry for partition walls (11.0 cm thick) in CM (1:4) prop. (Cement : Sand) using common burnt clay bricks of class as per Table- I of IS:1077-1992, Non- Modular or traditional size 23 x 11 x 7 cms from approved source having minimum crushing strength of 40 Kg/Sq.cm and placing 2 Nos. of 6mm M.S plain rods in every third layer with free ends of the reinforcement pegged into mortar joints of main brick walls where applicable including cost and conveyance of all materials like cement, steel, sand, bricks, water etc., to site, all operational, incidental charges such as labour charges for mixing cement mortar, scaffolding charges, constructing masonry, lift charges, curing, etc., but excluding cost of steel and its fabrication charges complete and including over head charges contractor profit but excluding GST & Seigniorage charges etc..complete for finished item of work. (APSS No. of 501 & 509)

Brick masonry walls in superstructure with CM (1:8) prop: (Cement : Sand) using common burnt clay bricks of class as per Table- I of IS:1077-1992, Non- Modular or traditional size 23 x 11 x 7 cms from approved source having minimum crushing strength of 40 Kg/Sqcm. including cost and conveyance of all materials like cement, screened sand, bricks, water etc., to site, labour charges, like mixing cement mortar, scaffolding charges, constructing masonry, lift charges, curing, etc.,and including over head charges contractor profit but excluding GST & Seigniorage charges etc..complete for finished item of work. (APSS No. 501 & 504) for Parapet in FF

Supply and placing of the Design Mix Concrete M 25 grade corresponding to IS 456 with cement content of 380 kgs per 1 cum of concrete using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate - as per IS 383 - 1970 and IS 2386 Part 1 to Part 8) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site, centering using casurina ballies, bamboos, wooden reapers, runners, wood posts, wall plates etc., including all operational, incidental and labour charges such as weigh batching, machine mixing, lifting of concrete manually, laying concrete, vibrating, curing , including overhead charges & contractors profit, but excluding GST & Seigniorage charges etc., complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402) for Lintels.

Supply and placing of the Design Mix Concrete M 25 grade corresponding to IS 456 with cement content of 380 kgs per 1 cum of concrete using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate - as per IS 383 - 1970 and IS 2386 Part 1 to Part 8) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site, centering using casurina ballies, bamboos, wooden reapers, runners, wood posts, wall plates etc., for 60cm wide sun-shades 7.5cm thick at fixed end and 5cm thick at free end with an average thickness of 6.25cm including all operational, incidental and labour charges such as weigh batching, machine mixing, lifting of concrete manually, laying concrete, vibrating, curing , including overhead charges & contractors profit, but excluding GST & Seigniorage charges etc., complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402, 403 & 903) for Sunshades

Supply and placing of the Design Mix Concrete M 25 grade corresponding to IS 456 with cement content of 380 kgs per 1 cum of concrete using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate - as per IS 383 - 1970 and IS 2386 Part 1 to Part 8) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site, centering using casurina ballies, bamboos, wooden reapers, runners, wood posts, wall plates etc., including all operational, incidental and labour charges such as weigh batching, machine mixing, lifting of concrete manually, laying concrete, vibrating, curing , including overhead charges & contractors profit, but excluding GST & Seigniorage charges etc., complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402) for Roof Beams.

Supply and placing of the Design Mix Concrete M 25 grade corresponding to IS 456 with cement content of 380 kgs per 1 cum of concrete using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate - as per IS 383 - 1970 and IS 2386 Part 1 to Part 8) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site, centering using casurina ballies, bamboos, wooden reapers, runners, wood posts, wall plates etc., including all operational, incidental and labour charges such as weigh batching, machine mixing, lifting of concrete manually, laying concrete, vibrating, curing , including overhead charges & contractors profit, but excluding GST & Seigniorage charges etc., complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402) for Roof Slab 125mm thick.

Supply and placing of the Design Mix Concrete M 25 grade corresponding to IS 456 with cement content of 380 kgs per 1 cum of concrete using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate - as per IS 383 - 1970 and IS 2386 Part 1 to Part 8) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site, centering using casurina ballies, bamboos, wooden reapers, runners, wood posts, wall plates etc., including all operational, incidental and labour charges such as weigh batching, machine mixing, lifting of concrete manually, laying concrete, vibrating, curing , including overhead charges & contractors profit, but excluding GST & Seigniorage charges etc., complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402) for Stair case Slab 100mm thick.

Reinforced Cement concrete (1:3:6) using 40 mm HBG graded metal from an approved quarry including cost and conveyance of allmaterials like Cement, Sand, coarse aggregate, water etc., to site including machine mixing charges and curing charges, lift charges and centring charges and including contractors profit and overhead charges etc., complete for finished item of work for dummy columns over ground floor roof slab. (APSS No. 402) for Dummy columns over ground floor roof slab.

Providing Thermo Mechanically Treated (TMT) / High Yield Strength Deformed (HYSD) (Fe 500 / Fe 500 D grade as per IS 1786-1979) of different diameters for RCC works including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap-splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars, including all wastages such as overlaps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying etc., and overheads & contractors profit, but excluding GST charges etc., complete for finished item of work.( APSS No.126)

Providing impervious coat to exposed RCC roof slab surfaces to required slopes with CM (1:3) prop. using screened sand 20mm thick (average) mixed with integral cement water proofing admixture confirming to IS: 2645-2003 manufactured by reputed manufacturers as approved by Engineer-in-charge at 100ml per one bag of cement, laid over roof slab when it is green, finished smooth with a floating coat of neat cement and thread lining at regular intervals of 45cmx45cm including cost and conveyance of all materials like cement, sand, water proofing compound, water etc., to site, operational, incidental, and labour charges for mixing mortar, laying, lift charges, rendering smooth and thread lining, curing including rounding off junctions of wall and slab etc., and including over head charges & contractor profit, but excluding GST & Seigniorage charges etc..complete for finished item of work. (APSS No. 901 & 903) over Roof Slabs

Ornamental plastering 12mm thick single coat in CM (1:3) using screened sand including cost and conveyance of all materials like cement, sand, water etc., to site and all operational, incidental charges on materials and including cost of all labour charges for mixing mortar, finishing, curing as directed by Engineer-in-charge etc., and including over head charges & contractor profit, but excluding GST & Seigniorage charges etc..complete for finished item of work.(SS 901,903 & 904) for ceiling plastering

Plastering 12mm thick in two coats using screened sand with base coat of 8mm thick in CM (1:6) and top coat of 4mm thick in CM (1:4) with dubara sponge finishing including cost and conveyance of all materials like cement, sand, water etc., to site and all operational, incidental charges on materials and including cost of all labour charges for mixing mortar, finishing, scaffolding, lift charges, curing, including cutting grooves as directed by Engineer - in - charge etc., and including over head charges & contractor profit, but excluding GST & Seigniorage charges etc..complete for finished item of work. (SS 901,903 & 904) for Internal walls

Plastering 20mm thick in two coats using screened sand with base coat of 16mm thick in CM(1:6) and top coat of 4mm thick in CM(1:4) with dubara sponge finishing including cost and conveyance of all materials like cement, sand, water etc., to site and all operational, incidental charges on materials and including cost of all labour charges for mixing mortar, finishing, scaffolding, lift charges, curing, including cutting grooves as directed by Engineer-in-charge etc., and including over head charges & contractor profit, but excluding GST & Seigniorage charges etc..complete for finished item of work .(SS 901,903 & 904) For Buildig Out side walls

Supply and fixing of MediumTeak wood Door double shutter fully panelled door of size 1.20 x 2.1mt with frame made of well seasoned Teak Wood scantlings of size 100 x 75mm and shutter side rails 100mm X 32mm, top rail 100 mmX32 mm, bottom rail 100mmX 32 mm and intermediate rails of 100mm x 32 mm and planks s - 10 no's of 25mm thick as per approved design with fixtures of 6 nos of 9" ' z" holdfasts, 350 mm long bross aldrop-1 no, 125mm long bross butt hinges 6 No's, bross Door stoppers-2 no, 250mm bross tower bolt - 2nos, 150mm long bross Tower bolts 1- no, bross fancy handles 250 mm -2nos with necessary screws complete including cost and conveyance of all materials and labour charges, over heads and contractor's profit etc. complete but excluding GST & Seionarage charges.as per specifications (APSS NO.1001 & 1002) .

Supply and fixing of Sal /Countrywood Door Frame of size 1.00 x 2.1mt with frame made of well seasoned Sal Wood scantlings of size 100 x 75mm fixing of fixtures of 6 nos of 9" ' z" holdfasts, complete including cost and conveyance of all materials and labour charges, over heads and contractor's profit etc. complete but excluding GST & Seionarage charges.as per specifications (APSS NO.1001 & 1002) .

Supply and fixing of Sal /Countrywood Door Frame of size 0.90 x 2.1mt with frame made of well seasoned Sal Wood scantlings of size 100 x 75mm fixing of fixtures of 6 nos of 9" ' z" holdfasts, complete including cost and conveyance of all materials and labour charges, over heads and contractor's profit etc. complete but excluding GST & Seionarage charges.as per specifications (APSS NO.1001 & 1002)

Supply and fixing of Door Frame of size 0.8x 2.10mt with solid Wood Polymer Composite (WPC) single extruded Door Frame section of size 45X75mm with encapsulation of 8MM rigid layer on all the six surfaces. The door frame will have a rebat of 32MM The two Vertical members are to be joined together with the horizontal member using 8x50 MM long MS Star full thread screws to be used with reverse forward speed control hand drilling machine. The ready/assembled door frame is fixed to the wall using hold fast or bolt fasteners. A minimum of 4 No.s of screws to be provided for each vertical member & minimum 2no.s for horizontal memberwith fixtures of 6 nos of 9" ' z" holdfasts with necessary screws complete including cost and conveyance of all materials and labour charges, over heads and contractor's profit etc. complete but excluding GST as per specifications (APSS NO.1001 & 1002)

Supply and fixing of Flush door Single Shutter to the existing sal wood door frame of size 1.00 x 2.10mt and Flush door Single Shutter, Solid bond wood block board type with teak veneer on one face and commericial ply on another face (lipping) ; 30 mm thick confirming to IS 2202 ( AS per BMT- N- 21) as per approved design with fixtures of 250 mm long MS-Powder Coated aldrop-1 no, 100mm long MS-Powder Coated butt hinges 3 No's, 150mm long Brass Tower bolts 1- no, MS-Powder Coated Door stoppers - 1no, MS-Powder Coated Door handles 150 mm -2nos with necessary screws complete including cost and conveyance of all materials and labour charges, over heads and contractor's profit etc. complete but excluding GST as per specifications (APSS NO.1001 & 1002)

Supply and fixing of Flush door Single Shutter to the existing sal wood door frame of size 0.90 x 2.10mt and Flush door Single Shutter, Solid bond wood block board type with teak veneer on one face and commericial ply on another face (lipping) ; 30 mm thick confirming to IS 2202 ( AS per BMT- N- 21) as per approved design with fixtures of 250 mm long MS-Powder Coated aldrop-1 no, 100mm long MS-Powder Coated butt hinges 3 No's, 150mm long Brass Tower bolts 1- no, MS-Powder Coated Door stoppers - 1no, MS-Powder Coated Door handles 150 mm -2nos with necessary screws complete including cost and conveyance of all materials and labour charges, over heads and contractor's profit etc. complete but excluding GST as per specifications (APSS NO.1001 & 1002)

Providing and fixing 28 -30 MM thick solid Wood Polymer Composite(WPC) single extruded door of siae 0.80 shutter with 3MM top and bottom rigid layer with an overall density of 750kg/Cum. It will be fixed to the frame using 3 inch /4 inch hinges. A minimum of 4 hinges will be required for fixing the door with the frame. A minimum of 4 hinges will be required for fixing the door with the frame as per approved design with fixtures of 250 mm long MS Powder coated Aldrop-1 nos, 150mm long Stainless steel T-Hinges 4 No's,150mm long MS Powder coated Tower bolts 1- no, MS Powder coated fancy handles 150 mm 2nos with necessary screws complete including cost and conveyance of all materials and labour charges, over heads and contractor's profit etc. complete but excluding GST etc., complete and including contractors profit and overhead charges etc., complete for finished item of work.

Supplying and fixing of MS Grill to windows / in open court yards using 25mm x 6mm MS flat alround and 10mm MS square bars horizontally at 125mm centre to centre and vertically at 300mm centre to centre including fixing with 4 Nos of MS Z holdfasts (2 on each side) duly making cutting brick masonry, fixing and making to original surface neatly including cost and conveyance of all materials, cutting, bending, welding, operational charges, labour charges, and including over head charges & contractor profit, but excluding GST charges etc..complete for finished item of work for window grills

Providing and fixing factory made uPVC white colour sliding glazed window comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVCprofile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mmsize for fixing frame to finished wall and necessary stainless steel screwsetc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage ofwater etc. After fixing frame the gap between frame and adjacent finishedwall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge inclusive of cost of Single / double glass panes, wire mesh and silicon sealent . Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.. Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of frame 92 x 44 mm & sash 32 x 60 mmboth having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension

Supply & applying Melamine Polish Glossy/ Matt finish to the wood works duly cleaning the surface and applying emery paper, sand the wood with 180 No., emery paper and then with 320 No., emery paper, clean & wipe off loose dust, applying suitable knifing paste filler / wood filler by putty knife / muslin pad, air dry for 2 - 3 hrs, sand with 180 and 320 No., emery paper, apply two component wood sealer, air dry for 24 hrs, sand with 320 No emery paper, applying one coat of approved spraying thinner (for spraying)/ applying one coat of approved brushing thinner or general purpose thinner (for brushing) and apply (either with spray or brush) two coats of approved brand melamine including cost & labour charges, emery papers, cost of thinner & melamine polish, over heads and contractors profit etc., complete for finished item of work

Supplying and fixing of Fixed Louvered Ventilators made of pre - painted steel (base steel as per IS 513 of -0.58 mm thick 'D" quality, galvanized as per IS 277 with zinc of 120 GSM) primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer, The section for louvered ventilators should be of of 33 x 56 mm Box section paneled with 4 mm pinhead glass with Ethyl propylene Diamine monomer Gasket (EPDM) and the sections cut to length mitre joined with corner bracket . corner brackets made of CRCA with Zinc Phosphate. The frames to be fixed to the concrete /masonry wall by means of self expanding screws including 10 mm square guard bars with 6" pitch including cost cost and conveyance of all materials, labour charges for fixing, overheads and contractors profit etc., complete for finished item of work in all floors.

Painting to new iron work with two coats of ready mixed synthetic enamel paint Grade-I first quality all shades over a base coat of red oxide primer making total 3 coats in all to give an even shade after thouroughly brushing the surface to remove all remains of loose powdered materials, including cost and conveyance of all materials, site and other taxes, all operational, incidental and labour charges etc., complete for finished item of work and including contractors profit and overhead charges etc., complete.

Flooring with Double charged / multi charged stain free full body porcelain vitrified tiles with double layer pigment of size 600 x 600 mm and thickness between 8-10 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs with borders and design as per the approved flooring pattern as directed by the Engineer-In -Charge, laying tiles using spacers of 2mm thick, set over a base coat of CM (1:8) prop. 12mm thick using screened sand over CC bed already laid or RCC roof slab , including neat cement slurry of honey like consistancy spread @ 3.3 kgs per sqm. and jointed neately with white cement paste to full depth mixed with pigment of matching shade including cost and conveyance of all materials like cement, sand, water, tiles, white cement etc., to site (excluding cost of C.C. bed) including cost of base coat and all labour charges for mixing of cement mortar, laying tiles to required slope as directed by the Engineer- in-charge etc.,and including over head charges & contractor profit, but excluding GST & Seigniorage charges etc..complete for finished item of work. (APSS No.701 & 707) for all rooms.

Providing skirting 10 cm height with Double charged / multi charged stain free full body porcelain vitrified tiles with double layer pigment of Size 600 x 600 mm and thickness between 8-10 mm of any colour and finish in all shades and designs, length equal to flooring tiles, flushed to wall surface to set over base coat of CM(1:5) 12 mm thick using screened sand with cement slurry of honey like consistency spread at the rate of 3.30 kgs per sqm and jointing with white cement paste mixed with pigment of matching shade to full depth, including cost of all materials like tiles, cement, sand and water etc.,and including over head charges & contractor profit, but excluding GST & Seigniorage charges etc..complete for finished item of work.(APSS No.701 &707)

Flooring with non-skid red or white full body Ceramic floor tiles of size 300 mm x 300 mm and thickness between 7-8 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs as approved by Engineer-in-charge, set over base coat of cement mortar (1:8), 12mm thick using screened sand over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3 Kgs per sqm & jointed neatly with white cement paste to full depth mixed with pigment of matching shade, including cost of all materials like cement, screened sand , water and tiles etc., and including over head charges & contractor profit, but excluding GST & Seigniorage charges etc..complete for finished item of work. (APSS No.701 & 707)

Providing dadooing with glazed red or white full body ceramic wall tiles of size 300 x 450 mm / 320 mm x 400 mm and thickness 6 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs with borders as approved by Engineer-in-Charge flushed to wall surface set over base coat of CM(1:5) 12 mm thick using screened sand with cement slurry of honey like consistency spread at the rate of 3.30 kgs per sqm and jointing with white cement paste mixed with pigment of matching shade to full depth, including cost of all materials like tiles, cement, sand and water etc., and including over head charges & contractor profit, but excluding GST & Seigniorage charges etc..complete for finished item of work. in Toilets

Painting to New walls with one coat water based cement primer of interior grade I and two coats of acrylic emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/litre for internal walls in all to give an even shade after thoroughly brushing the surface to remove all loose powdered materials, including cost and conveyance of all materials, labour charges, cost of brushes, water to site, etc., sales & other taxes, all operational, incidental and labour charges such as scaffolding charges, lift charges, curing and including over head charges & contractor profit, but excluding GST charges etc..complete for finished item of work in all floors for internal Walls .(APSS No. 912)

Painting to New walls with one coat water based cement primer of interior grade II and two coats of acrylic emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/litre for external walls in all to give an even shade after thoroughly brushing the surface to remove all loose powdered materials, including cost and conveyance of all materials,Labour charges cost of brushes, water to site, etc., sales & other taxes, all operational, incidental and labour charges such as scaffolding charges, lift charges, curing and including over head charges & contractor profit, but excluding GST charges etc..complete for finished item of work in all floors for external Wall

Construction of Compound Wall

Earth work excavation for foundations (Manual Means) of buildings, septic tank, sump, compound wall in ordinary soils and depositing on bank with an initial lead of 10m and depth up to 3m including all operational, incidental, labour charges such as shoring, sheeting, planking, strutting etc., and including over head charges & contractor profit, but excluding GST & Seigniorage charges etc., complete for finished item of work excluding dewatering charges etc., as per SS 20 B(APSS 308)

Filling with Stone Dust in trenches,sides of foundations and basement with initial lead in layers not exceeding 15cm thick,watering and ramming including cost and conveyance of water to work site and all operaitonal,incidental, labour charges,hire charges of T&P etc., and including over head charges & contractor profit, but excluding GST & Seigniorage charges etc., complete for fnished item of work(APSS NO.309&310)

Plain Cement Concrete (1:4:8) (cement: fine aggregate: Coarse aggregate) for foundations using coarse aggregate 40mm size hard , machine crushed granite from approved quarry using concrete Mixer 10 / 7 cft (0.2 / 0.8 cum) capacity including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site including all charges for machine mixing and hire charges of concrete mixer, laying concrete in foundations and under flooring bed, ramming in 15 cm layers finishing top surface to the required level curing etc., and including over head charges & contractor profit, but excluding GST & Seigniorage charges etc., complete, for finished item of work. (APSS No. 402) Bed Concrete for Footings

VRCC M - 20 Nominal mix (Cement:fine aggregate: coarse aggregate) corresponding to Table 9 of IS 456 using 20 mm size graded machine crushed hard granite metal (coarse aggregate) from an approved quarry using 350.00 kgs of cement/ 1 cum of concrete including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including sales & other taxes on all materials including all operational, incidental and labour charges such as machine mixing, laying concrete, curing concrete etc.,complete and including contactors profit and ovehead charges etc., complete but excluding cost of steel and its fabrication charges for finished item of work for Column Footings.

VRCC M- 20 Nominal mix (Cement:fine aggregate: coarse aggregate) corresponding to Table 9 of IS 456 using 20 mm size graded machine crushed hard granite metal (coarse aggregate) from an approved quarry using 350.00 kgs of cement/ 1 cum of concrete including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including sales & other taxes on all materials including all operational, incidental and labour charges such as machine mixing, laying concrete, curing concrete etc.,complete but excluding cost of steel and its fabrication charges and including contactors profit and ovehead charges etc., complete for finished item of work for Columns

VRCC M- 20Nominal mix (Cement:fine aggregate: coarse aggregate) corresponding to Table 9 of IS 456 using 20 mm size graded machine crushed hard granite metal (coarse aggregate) from an approved quarry using 350.00 kgs of cement/1 cum of concrete including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including sales & other taxes on all materials including all operational, incidental and labour charges such as machine mixing, laying concrete, curing concrete etc.,complete but excluding cost of steel and its fabrication charges and including contactors profit and ovehead charges etc., complete for finished item of work for Plinth Beam.

Masonry work in CM(1:8) prop (Cement : Sand) in superstructure with fly ash cement / lime solid blocks of size 290mm x 150mm x 140mm from approved source having minimum crushing strength of 50 Kg/Sqcm. including cost and conveyance of all materials like cement, sand, fly ash cement / lime solid blocks, water etc., to site, labour charges, like mixing cement mortar, scaffolding charges, constructing masonry, lift charges, curing, including over heads and contractor's profit but excluding GST & Seigniorage Charges etc. complete for finished item of work. (APSS No. 501 & 504).

Plastering 12mm thick in two coats using screened sand with base coat of 8mm thick in CM (1:6) and top coat of 4mm thick in CM (1:4) with dubara sponge finishing including cost and conveyance of all materials like cement, sand, water etc., to site and all operational, incidental charges on materials and including cost of all labour charges for mixing mortar, finishing, scaffolding, lift charges, curing, including cutting grooves as directed by Engineer - in - charge etc., and including over head charges & contractor profit, but excluding GST & Seigniorage charges etc..complete for finished item of work. (SS 901,903 & 904) For compound wall

Painting to New walls with one coat water based cement primer of interior grade II and two coats of acrylic emulsion paint having VOC (Volatile Organic Compound) content less than 50 grams/litre for external walls in all to give an even shade after thoroughly brushing the surface to remove all loose powdered materials, including cost and conveyance of all materials,Labour charges cost of brushes, water to site, etc., sales & other taxes, all operational, incidental and labour charges such as scaffolding charges, lift charges, curing and including over head charges & contractor profit, but excluding GST charges etc..complete for finished item of work in all floors for Compound Wall

Providing Thermo Mechanically Treated (TMT) / High Yield Strength Deformed (HYSD) (Fe 500 / Fe 500 D grade as per IS 1786-1979) of different diameters for RCC works including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap-splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars, including all wastages such as overlaps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying etc., and overheads & contractors profit, but excluding GST charges etc., complete for finished item of work.( APSS No.126)

Providing Water Supply & sanitary items

Drilling of Bore well by down the hole hammer drilling to a finished dia of 165 mm dia in all formations suitable for down the hole hammer drilling such as medium hard rock formation to hard rock formation, all consolidated formation etc. and drilling in over burden to dia not less than 200 mm etc and reaming the bore well to suit insertion of suitable casing pipe etc., including insertion of casing pipe with couplings, caps any other relevant materials upto required depth as directed by the department including transportation of drilling rigs and supporting vehicle and including bore development (Flushing of Bore Well at an average pressure of 150 PSI) conducting yield test, consumables charges, Crew charges required in fixation of pipe assembly completely done to the satisfaction of the department and including all labour charges but excluding all taxes, the cost of casing pipe, couplings, cap etc., complete for finished item of work and including contactors profit and ovehead charges but excluding GST etc complete. The entire work should be carried out as per IS -2800 Part I & II 1979 and amended from time to time.

Supply and fixing of 180 mm dia PVC Casing pipe perforation charges per RM including cost and conveyance of all materials,Labour charges and including contractors profit and overhead charges etc., complete for finished item of work. (IS15778:2007)

Supply and erecting of ISI mark 5 star rated submersible motor pumpset 1.00 HP single phase 10 stage conforming to IS 8034 and motor conforming to IS 9283 with water proof winding, pump shall be suitable for various delivery and discharge with stainless steel shaft suitable for 106 mm/156 mm dia borewells with high quality water resistnt and dynamically balanced bronze impeller with stainless steel shaft sleeves, pump coupling and pivot of single phase 250 V, single phase 50 HZ AC power supply copper winding with water proof insulation and high precision strength not to be affected by chemical in water and suitable bronze bearings with nut and bolts etc., with necessary H - type clamp of subitable size and strength and including etc., complete and including contactors profit and ovehead charges but excluding GST etc complete for finished item of work.

Cost, fabrication , transportation and supply of suitable size panel board for single phase submersible motor up to 1.5 HP consisting of relay, Contactor, starting and running capacitors, Voltmeter, Ammeter, indicator lamps, MCB , on/off switch including supply and fixing of DOL starter etc., complete including cost and conveyance of all materials,Labour charges and including contactors profit and ovehead charges but excluding GST etc complete.

Supply, delivery, and laying of 32 mm OD 10.00 kgs/cm2 HDPE pipe conforming to IS 4984-1995 including transportation charges including cost and conveyance of all materials, Labour charges and etc., complete for finished item of work and including contactors profit and ovehead charges but excluding GST etc complete.

Supply of 3 Core 2.50 Sq. mm Flat Copper cable of ISI for Submersible Motors confirming to IS: 694:1990 including cost and conveyance of all materials, Labour charges and etc., complete for finished item of work and including contactors profit and ovehead charges byt excluding GST etc complete.

Supply of fixing of SS Nipples of 32 mm x 25 mm diameter stainless steel nipples including cost and conveyance of all materials and all labour charges etc., complete and including contactors profit and ovehead charges but excluding GST etc complete.

Supply and fixing of bore cap of 180 mm dia including cost and conveyance of all materials, Labour charges and etc., complete for finished item of work and including contactors profit and ovehead charges byt excluding GST etc complete.

Cost, supply and delivery of 110 mm diameter 6.00 kgs/cm2 test pressure Unplasticised PVC pipes suitable for potable water supplies conforming to IS 4985/200 (3rd revision) as per specifications including labour charges for laying, fixing and commissioning the PVC pipes including couplers/bends/tees etc., including fixing with necessary fittings like bends, plugs, couplers, juctions, tees etc., with solvent jointing as per standard practise including cost and conveyance of all materials etc., to site for finished item of work at all floor levels and including contactors profit and ovehead charges but excluding GST etc complete.

Cost, supply and delivery of 75 mm diameter 6.00 kgs/cm2 test pressure Unplasticised PVC pipes suitable for potable water supplies conforming to IS 4985/200 (3rd revision) as per specifications including labour charges for laying, fixing and commissioning the PVC pipes including couplers/bends/tees etc., including fixing with necessary fittings like bends, plugsm couplers, juctions, tees etc., with solvent jointing as per standard practise including cost and conveyance of all materials to site for finished item of work at all floor levels and including contactors profit and ovehead charges but excludingf GST etc complete.

Supply and fixing of Ashirvad/Ajay/Astral flow guard or equivalent CPVC pipes ( 22.20mm OD ) and fittings to meet the requirement of ASTM-D-2846 and are produced in CTS.IS 15778:2007) for hot and cold water.pipes are made from idential CPVC compounds having the same physical Properties for Hot and Cold Water (IS 15778:2007) including cost and conveyance of all material to work site, all labour charges for all operations for fixing etc.. Complete including Cost and and conveyance of all materials and labour charges ,over heads and contractor's profit, but excluding GST charges, etc., complete for for finished item of work

Supply and fixing of CPVC pipes (28.60 mm OD Pipe-SDR 13.5) and fittings to meet the requiremnet of ASTM-D2846 and are produced in CTS ( copper tube size 1/2" ton 2" SDR 11 and SDR 13.5 pipes are made from identical CPVC compounds having the same physical properties for HOT and cold water Ashirvad/Ajay/Astral flow guard or equivalent including cost and conveyance of all material to work site, all labour charges for all operations for fixing etc.. including Cost and and conveyance of all materials and labour charges ,over heads and contractor's profit, but excluding GST charges, etc., complete for for finished item of work

Supply and fixing of CPVC pipes (34.90 mm OD Pipe-SDR 13.5) and fittings to meet the requiremnet of ASTM-D2846 and are produced in CTS ( copper tube size 1/2" ton 2" SDR 11 and SDR 13.5 pipes are made from identical CPVC compounds having the same physical properties for HOT and cold water Ashirvad/Ajay/Astral flow guard or equivalent including cost and conveyance of all material to work site, all labour charges for all operations for fixing etc.. including Cost and and conveyance of all materials and labour charges ,over heads and contractor's profit, but excluding GST charges, etc., complete for for finished item of work

Supplying and fixing European Water Closet of 1st quality conforming to IS:2556-Part-2-1973 of white glazed with 'S' trap,supplying and fixing best Indian make plastic seat and lid for European water closets with rubber or plastic Buffers as per IS 2548-1996 and 10 litres capacity single flush PVC low level cistern with internal components and fixed using required size of nails and screws, angle stop cock 12.70mm dia. first quality Indian make heavy duty, 12mm PVC connections with brass union nuts CP coated including cost and conveyance of all materials to site, and including overheads & contractors profit but excluding GST charges for finished item of work for all floors

Supply and fixing of Orissa Pan white glazed water closet of size 580 mm x 440 mm 1st quality conforming to IS: 2566 Part - 3, 1981 of makes Hindustan/Nycer/Parryware white glazed with P OR S Trap including cost and conveyance of all materials to site and all labour charges etc., complete for finished item of work and and including overheads & contractors profit but excluding GST charges etc., complete.

Supplying and fixing Indian make Flat Back Wash Hand Basin (HSW/Parryware/ Neycer) 1st quality confirming to IS:2556-Part-4:1972 with waste fittings like rubbe plug, chain, 32mm nominal size C.P. Fitting with parallel pipe thread confirming to IS:2963-1979 and fitted with 15 mm nominal bore Chromium Plated Pillar Tap of 1st quality Indian make 400 grams Seiko/ Senior / Nice / Esso or equivalent complete with standard CI brackets including wooden block: including cost of 50mm dia pvc pipe, 12.7mm PVC connection with brass union nut C.P. coated and concealed stop cock 12.7 mm (1/2") etc complete for 550 x 400 mm - Single C.P Pillar cock including Cost and conveyance of all materials and labour charges including over heads and contractor's profit but excluding GST charges etc., complete for finished item of work

Supply and fixing of 12.7 mm N.P bib tap Indian make heavy duty long body including fixing of CP flange including Cost and conveyance of all materials and labour charges including over heads and contractor's profit but excluding GST charges etc., complete for finished item of work.

Providing and placing on terrace (at all levels) polyethylene water storage tank with double layer approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet and outlets and over flow pipes but without fittings and base suppport for tanks conforming to IS 12701-1996 including Cost and conveyance of all materials and labour charges including over heads and contractor's profit but excluding GST charges etc., complete for finished item of work.

Supply and fixing NP soap dish heavy type with NP screws including all charges etc., complete and including Cost and conveyance of all materials and labour charges including over heads and contractor's profit but excluding GST charges etc., complete for finished item of work.

Cost, supply and fixing of 20 mm diameter PPR ball valve conforming to DIN standards 8077/8092 including Cost and conveyance of all materials and labour charges including over heads and contractor's profit but excluding GST charges etc., complete for finished item of work

Cost, supply and fixing of 25 mm diameter PPR ball valve conforming to DIN standards 8077/8092 including Cost and conveyance of all materials and labour charges including over heads and contractor's profit but excluding GST charges etc., complete for finished item of work

Supply and fixing of 20 mm dia 2.10 mm thickness heavy grade with IS;9537 part 3 FRLS rigid P.V.C. pipes concealed in roof Slabs with all required accessories including masonary work and including cost and conveyance of all materials and all labour charges etc., complete and including contractors profit and overhead charges but excluding GST etc., complete. .

Supply and erecting fan hooks of 12/15mm dia M.S. rod / bar grouted in RCC slab with making the slab as original including cost and conveyance of all materials and all labour charges etc., complete and including contractors profit and overhead charges but excluding GST etc., complete. .

Supply and fixing of 25 mm outer dia (2.00 to 2.20 mm) thickness confirms to IS:9537 part 3 FRLS rigid P.V.C. pipe (ISI marked) concealed in wall with all required junction boxes and all accessories including masonary work for light, bell, fan, and separate plug point well seasoned wooden deep box including cost and conveyance of all materials etc., complete for finished item of work with earthing terminal including all labour charges and including over head charges & contractor profit, but excluding GST charges etc., complete Makes : Precision/Universal & Marudhar/ VIP /GoldMedal / Million plast / GM / Sudhakar /Polycab/Anchor/ Polyline/ Orbit/AKG/Beljin/Vasavi/DEC .

Wiring with 2 runs of 14/0.3mm (1.0 Sq.mm) Fire Retardant (FR) P.V.C. insulated flexible copper cable (ISI MARK) in existing pipe with 6A switch, Ceiling rose and 3mm thick hylam sheet covering to switch control box including all labour charges etc., complete for light, bell, fan and exhaust fan points in Non-Residential Buildings and including cost and conveyance of all materials and all labour charges etc., complete and including contractors profit and overhead charges but excluding GST etc., complete.

Supply and fixing of 6A 3 pin wall plug socket with 6A switch control on a common switch board with earth continuity including wire leads, earth connections along with cost and conveyance of all materials and all labour charges etc., complete and including contractors profit and overhead charges but excluding GST etc., complete.. .

Supply and fixing of batten holder / angle holder in lieu of ceiling rose of light point complete with all connections and including cost and conveyance of all materials and all labour charges etc., complete with 3.00 Watts LED Lamp etc., complete for finished item of work. (for new installation) and including contractors profit and overhead charges but excluding GST etc., complete. .

Supply and run of 2 of 36/0.3 mm (2.5 Sq.mm) F.R P.V.C. insulated flexible copper cable in existing pipe for mains including cost and conveyance of all materials and all labour charges etc., complete for finished item of work and including contractors profit and overhead charges but excluding GST etc., complete. .

Supply and run of 1 of 22/0.3 mm (1.0 Sq.mm) F.R P.V.C. insulated flexible copper cable in existing pipe for earth continuity including cost and conveyance of all materials and all labour charges etc., complete for finished item of work and including contractors profit and overhead charges but excluding GST etc., complete

Supply and fixing of 12 Model Dip galvanized 18 SWG Module metal box with earthing terminal including cost and conveyance of all materials and all labour charges etc., complete and including contractors profit and overhead charges but excluding GST etc., complete.

Supply and fixing of 8/9 Model Dip galvanized 18 SWG Module metal box with earthing terminal including cost and conveyance of all materials and all labour charges etc., complete and including contractors profit and overhead charges but excluding GST etc., complete.

Supply and fixing of 12 Model Modular Cover Frame including cost and conveyance of all materials and all labour charges etc., complete and including contractors profit and overhead charges but excluding GST etc., complete.

Supply and fixing of 8 Model Modular Cover Frame including cost and conveyance of all materials and all labour charges etc., complete and including contractors profit and overhead charges but excluding GST etc., complete.

Supply and fixing SPN Distribution board with IP-20 protection suitable for 40 A DP Isolator (DP) Isolator as incomer and 6-32 Amp 10kA SP MCBs - 6 Nos. as out goings including internal connections and labour charges for surface / flush mounting etc., complete for finished item of work including cost and conveyance of all materials and all labour charges and including contractors profit and overhead charges but excluding GST etc., complete. .

Supply and fixing of 20-24W, not less than 1100 mm length LED batten light with extruded alluminium housing and polycarbonate cover, input voltage AC 220 - 260 Volts with F>0.9, Surge protection: 2 KV,THD<15%, with inbuilt driver and frosted cover CCT: 3000 K - 5700 K, minimum CRI>70 etc., complete for finished item of work including cost and conveyance of all materials and all labour charges and including contractors profit and overhead charges but excluding GST etc., complete. .

Cost, supply and fixing of 1200 mm (48") sweep 230 V, A.C 50 Hz.Ceiling fan with 3 Blades and double ball bearings including giving connections, including cost and conveyance of all materials and all labour charges for fixing with all standard accessories etc., complete for finished item of work and including contractors profit and overhead charges but excluding GST etc., complete. .

Supply and erecting of stepped type electronic regulators for ceiling fans of 1200 mm sweep complete erected on existing switch board including cost and conveyance of all materials and labour charges etc., complete for finished item of work and including contractors profit and overhead charges but excluding GST etc., complete. .

Supply, transportation and fixing of 20 Watts LED Street light Luminaire made of pressure diecast alluminium body with powder coated, having protective toughned glass including all standard accessories etc., complete including cost and conveyance of all materials and all labour charges for fixing of street light luminaire on wall including giving connections etc., complete for finished item of work and including contractors profit and overhead charges but excluding GST etc., complete. .

Providing independent earthing by excavating trench to a depth of 0.90 meters in all soils as per size specified in data using 25 mm daimeter G.I pipe 'B' class with necessary accessories with hume pipe duly providing staggered holes including filling with equal proportion of salt and chorcoal in layers including cost and conveyance of all materials and all labour charges etc., complete for finished item of work and including contractors profit and overhead charges but excluding GST etc., complete. .

Supply and Run of 2 of 6 Sq.mm WPSC Aluminium cable along with No.10 SWG G.I bearer wire through PVC cleats with all accessories including labour charges etc., complete for service mains including cost and conveyance of all materials and all labour charges etc., complete for finished item of work and including contractors profit and overhead charges but excluding GST etc., complete. .

Supply and fixing of single phase meter on new peeta board 1 No. including fixing of 1 No., of 63 A 415 Volts rewirable fuse unit and 20A 1 Way 1 Module Modular Switch with Indicator including giving connections etc., complete including cost and conveyance of all materials and all labour charges etc., complete for finished item of work and including contractors profit and overhead charges but excluding GST etc., complete. .

Supply and erection of LED indicator lamps on the existing box / panel board including cost and conveyance of all materials and all labour charges etc., complete for finished item of work and including contractors profit and overhead charges but excluding GST etc., complete. . .

(No.of items 93) only