Renovation Work at Academic Block of State Institute for The Mentally Challenged, Pangappara, Thiruvananthapuram

Amount

CIVIL WORKS

Providing and fixing 18mm thick Pre-laminated medium density fibre board (Grade-I MDF Board) IS:14587:1998 marked, Pre-laminated with one side decorative other side balancing lamination Grade-I (exterior grade) in shelves with screws and fittings wherever required, edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand all complete as per direction of Engineer in charge.

Providing and fixing12 mm thick marine plywood conforming to IS: 710 for wall panelling with one side decorative lamination other side balancing lamination Grade-I (exterior grade) with screws and fittings wherever required, edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand all complete as per direction of Engineer in charge.

Providing and fixing wooden partition made of 12mm BWR ISI (303 Grade) plywood (Century, Greenply, Fineply or equivalent) with 1mm lamination at exposed area and 0.8mm inside laminate by Hot press Lamination (3m or Henkel) (Brand : MERINO, Associate or equivalent) of approved colour and pattern as per the design and direction of Engineer in charge. Partition top and side shall be provided with 16mm both side white laminated plywood (top side high glossy finish) with 1.3 mm thick glossy edge band. The frame work should be 16mm BWR grade plywood. All joints and necessary grooves in laminate to be given with smooth finish. the partition is firmly fixed to the floor and wall. Area of unit to be measured in elevation Only.

Providing and fixing powder coated telescopic drawer channels 300 mm long with necessary screws etc. complete as per directions of Engineer -in-charge.

Providing and fixing Clip on cabinet hinge-36mm-Full overlay type of approved quality including necessary screws etc.complete

Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete.75 mm

Providing and fixing chromium plated brass handles with necessary screws etc. complete: 125 mm

Providing and fixing glass panes with putty beeding and glazing clips for seperating work stations and front side at required height, all complete with 8mm thick toughened glass panes with neat finish

Providing and sticking Frosted Crystal Glass Film on glass panes in partition , doors etc.

Dismantling aluminium / Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable material with in 50 metres lead as directed by Engineer - in-Charge

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with: 12.5 mm thick tapered edge gypsum plain board conforming to IS : 2095-Part 1

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge ( Door handle, lock and stopper etc to be paid separately)

Providing and fixing SS H handle having min 30cm length in toughed glass door including all necessary.

Providing and fixing of 6 levers SS Lock with out handle in frameless glass door including all necessary .

Supply and fixing of Accoustic wall panelling using G.I Metal stud panelling using 48mm G.I.Studs placed at 595 centre to centre in 50mm floor channel and ceiling channel fixed with top and bottom and laying 50mm glass wool for insulation and accoustical purpose and then fixed 12.5mm thick Gyp.tone tile, size is 595mm x 595mm and fixing fibre tape with jointing compound for full finish on joints including applying one coat of putty and one coat of primer, two coats of Emulsion paint with fully finished for false ceiling/panelling

Supply and fixing of Accoustic ceilings using Interlock grid Main T 38mm x 24mm and sub T 24mm x 24mm and wall angle 24mm x 24mm and using suspension 6mm M.S.Rod/4mm G.I wire and adjustable 'J" bolt & nut and necessary hardware's grid size is 2'x2' (595mm x 595mm) and laying 12.5mm thick Gyp.board (Gyp.tone) and also supply and laying 50mm Glass wool on the top of gyp tone tile including applying one coat of putty and one coat of primer, two coats of Emulsion paint with fully finished for false ceiling/panelling

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

12 mm cement plaster finished with a floating coat of neat cement of mix :1:4 (1 cement: 4 fine sand)

Supplying and Placing wire mesh to the top of slab/AAC Block for plastering including cost of wire mesh , cutting and placing charges cost of conveyance etc. complete

25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with : Second class deodar wood

Providing and fixing carpet 8 mm thick of suitable colour for floor finishing.

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured), Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick:. 5.5mm thick glass pane

Providing and fixing in position the signage board made out of 3 mm opaque PVC foam board of computerised cut, PVC non reflective self adhesive vinyl painted foam board of size of 50 cm x 30 cm for "Name, Designation" sign board, 80 cm x 60 cm for various office name board : text - white colour, background in blue

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600 x 600 mm.

Providing and fixing Galvalume sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ .05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel rade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portion. Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately) For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.50 mm thickness

Providing and fixing tiled false ceiling of approved materials of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams per sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85x 30x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer -in-charge. 12.5 mm thick square edge PVC Laminated Gypsum Tile size 595x595 mm made of Gypsum plasterboard , manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16 mm thick fire retardant PVC film on the face side and 12 micron metalized polyster on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyster film so as to make the tile a completely sealed unit.

Furniture

Executive Desk : Executive desk on panel legs made of polished veneered melamine board top and panels. Desk complete with cable management tray, grommets, under desk storage drawers. Pedestal side table Table : 1500 x 900 x 750 mm (W x D x H), Pedestal : 900 x 600 x 700 mm (W x D x H)

Executive Chair: Medium back ergonomic chair with five nos. star shaped Nylon base. Castor: 50mm diameter nylon twin wheel, gas lift height adjustment, back angle adjustment and backrest height adjustment. Fixed armrest providing natural resting for arms. Seat with PU cutted foam backed fabric, back rest with leather cushion, upholstery: Brown leather finish. Director's Room

Executive Chair: Medium back ergonomic chair with five nos. star shaped Nylon base. Castor: 50mm diameter nylon twin wheel, gas lift height adjustment, back angle adjustment and backrest height adjustment. Fixed armrest providing natural resting for arms. Seat with PU cutted foam backed fabric, back rest with mesh type fabric, upholstery: Heavy duty rubber backed fabric in BLACK

Visitors Chair: Non-revolving executive chair with fixed armrest providing natural resting for arms. Seat with PU cutted foam backed fabric, back rest with mesh type fabric, Upholstery: Heavy duty rubber backed fabric in BLACK

Airport Chair 3 Seater , SS 201 grade (or better) steel perforated seat sheet and back rest, Width of seat 52cm to 55cm, height from ground 79cm.

Providing and fixing of durable signage/Name board made of Rectangular Vinyl Name Plate of minimum size 450mm x 150 mm with specified colour and all fixing arrangements as per design at the required location as per direction of engineer in charge.

Electrical Works

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Group C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required 2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providng and fixing 2 Nos. 3 pin 5/6 A modular socket outlets and 2 Nos. 5/6 A modular switches, connection etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/recessed steel/PVC conduit along with crimping of Cable with connectors as required

Supply and Fixing of RJ 45 data outlet in separate 2 modular box with GI Box and all connections complete

Supply and installation of recess mounted Round LED 18 W down light in die-cast aluminium housing including high efficiency diffuser provides soft glare free light, driver etc including all required mounting accessories complete. (Philips DN195B LED20S-6500 PSU WH S1 /Havells LHEBJNP7IN1WO18 /Wipro -LD90-231-XXX-65-XX ).

Supply and installation of compact Recess mounted 36W LED luminaire with High transculent diffuser gives soft glare free light & complete with electronic driver including all required mounting accessories complete. (Philips RC380B LED 34S 6500 PSU OD WH /Havells LHECDIL7PN1W036 / Wipro -CRCO 10R038HP57GL1)

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, miniature circuit breaker (MCB), in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supply, Installation, testing and commissioning of wall mount fan (400mm sweep), adjustable speed. Min 60 degree oscillation, swing, Adjustable upward and downward tilt mechanism, Protective Guard, Including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, mounting accessories, etc. as required. It shall be double ball bearning type. (Make: USHA, Cromption, Havells )

Supply, installation, testing and commissioning of best quality cat-6 patch cord having 1 metre length complete as per specifications as required.

Supply, installation and commissioning of powder coated DVR 6U Wall Mounted Server Rack of ISO Standard of size 400X 400X 200mm having depth adjustable mounting slots, top and bottom Panel with ventilation and cable entry facility, provision to mount the cooling fans on the top panel, lock and key etc. and having capacity to carry a max Load of 60 kg all complete as per the manufacturer specifications and instructions of Engineer In Charge.

24 Port Network Switch: Supply and Installation at site: 10/100 Mbps 24-Ports Gigabit Switch. (Make: D-Link D-Link DGS-1024D)

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required. 6 way (8+18) - three phase double cover (IP 42/43)

Supplying and fixing Cable End Box (Loose Wire Box) (IP 43) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with testing and commissioning etc. as required. For 6 way, Double door TPN MCBDB

Numbering of ceiling fan / exhaust fan/ fluorescent fittings as required.

Supplying and fixing extra down rod of 60 cm length G.I. pipe 15 mm dia, heavy gauge including painting etc. as required.

Supplying and laying armoured aluminium cable of following size in medium class PVC conduit including all accessories, GI clamps, terminations, glands etc as required. 3.5 core 35 sqmm armoured aluminium cable

CIS ELECTRICALS PVT LTD

MASTERCELL TELECOM SERVICES (P) LTD