Swachcha Bharat Mission (Urban) 2.0 Grant & 15th Finance Commssion Tide Grant 2025- 26 (2nd Installment)

Name of work : Construction Work of New Toilet Block and Repairing Work of Toilet Block in

Nagarpalika Various Area @ Kheda Nagar Palika, District: Kheda.

Discription of Work Estimated Amount

1 Construction Work of Toilet Block Opp. Fansichakla Police Station

2 Construction Work of Toilet Block in Vanzaravas

3 Repairing Work of Toilet Block Near Maharnapratap Circle Nadiad Highway

4 Repairing Work of Toilet Block in Sardar market

SB-1 (Construction Work of Toilet Block Opp. Fansichakla Police Station)

ITEM OF WORK QTY Rate UNIT AMOUNT

Excavation for foundation upto 1.5 m depth including sorting out and

1 stacking of useful materials and disposing off the excavated stuff upto 31.00 117.08 Cu.m

All lead.(A) Loose or soft soil

Excavation for foundation for depth from 1.5 m to 3.0 m including

sorting out and stacking of useful materials and disposing off the

excavated stuff upto All lead.(A) Loose or soft soil

Filling available excavated earth (excluding rock)in trenches, plinth,

3 sides of foundations etc. in layers not exceeding 20cm in depth 53.00 130.39 Cu.m

consolidating each deposited layer by ramming & watering.

Filling in foundation and plinth with murrum or selected soil in layers of

4 20cm. thickness including watering, ramming and consolidating etc. 23.50 282.02 Cu.m

complete. (more than 10 ton)

Providing and laying cement concrete 1:2:4 (1- Cement : 2- Coarse sand

: 4- graded stone aggregates 20 mm nominal size) and curing complete

excluding cost of formwork in (A) Foundation and Plinth (more than

Providing and laying controlled cement concrete work M250 and curing

complete including the cost of form work but excluding the cost of

reinforcement of reinforced concrete work in foundation, footings base

of column and mass concrete. (A) Footing (more than 10 ton)

Providing and laying controlled cement concrete work M-25 and curing

complete including the cost of form work but excluding the cost of

reinforcement of reinforced concrete work in Column, Pillers, posts

and struts. (more than 10 Ton)

Providing and laying controlled cement concrete work M200 and curing

complete including the cost of form work and excluding the cost of

reinforcement of reinforced concrete work in : (B) Column (more than

Providing and laying controlled cement concrete work M250 and curing

complete including the cost of form work and excluding the cost of

reinforcement of reinforced concrete work in : (C) Ground Beam (more

Providing and laying controlled cement concrete work M200 and curing

complete including the cost of form work but excluding the cost of

reinforcement of reinforced concrete work in Lintel or Copping. (D)

Providing and laying controlled cement concrete work M200 and curing

complete including the cost of form work but excluding the cost of

reinforcement of reinforced concrete work in Chajja. (E) chhajja .

(more than 10 ton)

Providing and laying controlled cement concrete work M200 and curing

complete including the cost of form work but excluding the cost of

reinforcement of reinforced concrete work in Floor Beams. (F) floor

Beams. (more than 10 ton)

Providing and laying controlled cement concrete work M200 and curing

complete including the cost of form work but excluding the cost of

reinforcement of reinforced concrete work in Slabs.(G) slabs, landing,

shelves, balconies etc (more than 10 ton)

Providing TMT Bar FE 415 reinforcement for R.C.C. work including

13 bending, binding and placing in position complete upto floor two level 4150.00 67.26 Kg.

(more than 10 ton)

Brick work using common burnt clay building bricks having crushing

strength not less than 35 kg./Sq.Cm. in foundation and plinth in

Cement Mortar 1:6 (1- Cement : 6 -fine sand) (B) Conventional (more

(i) Half brick masonry in common brunt clay building bricks having

crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1-

Cement : 4 -coarse sand ) in foundation and plinth (B) Conventional

(more than 10 ton)

Providing 15mm. thick cement plaster in single coat on rough (similar)

side of single or half brick walls for interior plastering up to floor two

level finished even and smooth in cement mortar 1:4 [1 cement:

sand) etc. complet

Providing & laying10 mm. thick cement plaster in single coat on fair

side of brick concrete walls & ceilings for interior plastering upto floor

two level and finishing with smooth mala plaster.(i) Cement mortar 1:3

(1 cement : 3 sand)

20 mm thick sand faced cement plaster on wall upto hight

metres above ground level consisting of 12mm thick backing coat of

c.m. 1 :3 (1 cement : 3 sand) and 8 mm thick finishing coat of c.m. 1 :

1 (1 cement : 1 sand) etc. complete

Providing throating or plaster drip and moulding to R.C.C. Chajja

Providing & Laying 24" x 24" vitrified 8 mm thick tile flooring over

mm (average) base of cement mortar 1:6 ( 1 cement: 6 coarse sand) on

20 new surface or fixing on existing flooring by adhesive material including 45.00 1397.83 Sqm

dismentaling of xisting flooring and jointed with color cement slurry

including finised with flush pointing & cleanin

Providing and laying light shade vitrified tiles 8mm to 10mm thick in

skirting,risers of steps and dedo on 10mm thick cement plaster

1:3 (1 cement : 3 Coarse sand) & jointed with white cement slurry for

light shed satin finish/Semi glossy.

Providing and laying polished kota stone slab flooring over

mm.(average) thick base of cement mortar 1:6 (1 cement : 6 coarse

sand) or L.M. 1:1.5 laid over and jointed with gray cement slurry

including rubbing & polishing etc. complete. [A] 25mm

Providing and laying polished Granite Slab 18mm thick in Risers of

steps Dedo, window sill, jembs and pillars laid 10mm thick Cement

23 Mortar 1:4 (1-Cement : 4-Coarse Sand) and jointed with Grey Cement 7.00 2990.00 Sqm

Slurry including full molded round front edges , rubbing and polishing

Providing and fixing flush door with I.T.W. beading all around by using

I.T.W. frame 100 m.m. x 70m.m.. shutter fabricated from 35 mm thick

solid core non decorative flush door exterior grade bonded BWP/BWR

synthetic resin having stamped IS 12823 grade I type II including

24 priming coat & two coats of painting on surfaces and Stainless steel 4.50 3129.99 Sqm

decorative type designs fixtures / fastening 2Nos. Handles, 2Nos.

Aldropes, towerbolt etc.including I.T.W. triangular batten patti of size

30m.m.x30m.m.etc. as per architectural detailed drawing and as

directed by engineer in charge.

Providing and fixing FRP FRAME size 100 x 50mm and 28mm thick FRP

depress pannel shutter having extra reinforcement on sides and edges

and in gel coat finish. The core of the shutter is to be filled up with

injected fire retardent grade polyurethane foam done in situ along with

embedded wooden places for stiffening and also for tacking hinges and

fixture. The hole FRP frame and shutter is to be water proof, water

proof, termite proof and resistance to mild acid/Alkali. Rates are to be

inclusive of S.S hinges with necessary screws and Alluminium fixture

and fastening.Product should have 3 years prefomance guarantee and

company have ISO 9001-2000 certificate.

Providing & fixing standard extructed of alluminium section of size

63mm x 38.10 mm x12 mm (jindal section 2434 @ wt..643 kg/mt.) with

colour anodized alluminium frame for ventilation with 5 mm thick

frosted glass as details etc.complete for Ventilation

Providing and fixing M.S. Gate of required pattern to marble/ granite

frames of window etc. with M.s. flats at required spacing and frames

alround, square or round bars fixed with round headed bolts and nuts

or by screws, including oil painting with one coat of primer of approved

quality and brand & two coats of synthetic enamal oil paint etc.

complete as per detail drawing and as directed by Engineer in charge.

Finishing wall with weather proof exterior emulsion paint on wall

surface (two coats) to give an required shape even shade after

thoroughly brushing the surface to remove all dirt, and remains of

loose powdered materials.etc complete

Applying two coats of Birla or Asian acrylic lappy (putty) and two coats

of primer of approved brand and manufacture on new wall surface to

give an even shade including thoroughly brushing the surface free from

mortar dropping and other foreign matter and sand prepared smooth.

and Wall painting (two coats) with plastic emulsion paint of approved

brand and manufacture on undecorated wall surface to give an even

shade including throughly brushing the surface free from mortar

droppings and other foreign matter and sand papered smooth.

Providing and laying China Mosaic type water proofing treatment on

terrace including (a) Applying neat cement slurry 2.75 Kg./Smt. of

cement admix with water proofing compound after cleaning the

surface (b) 50 mm thk. Cement Concrete flooring 1:2:4 (1-Cement : 2-

Coarse sand : 4-graded stone aggregate 20 mm nominal size) laid in

admixed with water proofing compound including rounding of

junctions of walls and slabs (c) after two days of proper curing applying

a second coat of cement slurry (d) finishing the surface with 20mm

thick cement mortar 1:4 (1 cement : 4 coarse sand) and china mosaic

tilling & finally finishing the surface with trowel with white cement

slurry (e) after finishing the whole terrace shall be flooded with water

for a period of two weeks.

Carrying out plinth treatment to post constrution/existing structrue by

spraying chemical solution for termite control treatment including

labour and material consistent with I.S.I specification. Using chloride

and Chiorpurfiles 20 EC. Asper 6131_ paret-II Consentration Weight

one percent is recommended i.e. one litre 20 EC chemical emulsion

with 19 litre give 1% concentration inclusive of one litre chemical

emulsion application at the rate of 5 litre chemical/sqmt. of surface is

recommended as per I.S.

WATER SUPPLY AND SANITATION

Providing & fixing water closet squatting pan ( Orrisa type W.C. pan)

size 580 mm including 100 mm P or S trap for water closet squatting

32 pan incl. jointing the trap with the pan & soil pipe in cement mortar 5.00 933.78 Each

1:1(1 cement : 1 fine sand)(including earthwork, bed concrete, foot

ress and trap) (A) Vitreous China : (i) long pattern white colour

Providing and fixing wash down water closet (european type W C pan)

with integral P and S trap including jointing the trap with soil pipe in

cement mortar 1:1 ( 1 cement fine sand) including Providing and fixing

Plastic Seat and cover for wash down water closet with C.P. brass

hinges and rubber buffers and also includes provide and fixing jet wash

Facilities complete

(A)Vitereous China Pattern:

(I) in White Colour

Providing and fixing washbasin with single hole for pillar trap at all floor

level with C.I. or M.S. Brackets painted white including cutting holes

and making good the same (A) Vitreous china flat back wash basin

550mm x 400mm size in white colour including (a) providing and fixing

34 C.P. brass waste for wash basin or sink(A) 32mm (b) providing and 4.00 2115.16 Each

fixing M.I.fisher union for wash basin or sink(A) 32mm (c) piller

tap,capstan head, screw down high pressurewith screw shanks and

back nuts for 15mm dia. for all floor (d)brass screw down stop tap

Providing & fixing 600 mm. x 450 mm. bevelled edge mirror of superior

glass at all floor levels, mounted on 6 mm. th. A.C. sheet or plywood

sheet & fixed to wooden plugs with C.P. brass screws and washers etc.

Providing and fixing PVC SWR Nanhi trap IS 14735 for drain -100 mm

diameter with jali of the following nominal diameter of self cleaning

design with C.I scead down or hinged grating including the cost of

cutting and making good the wall.

Providing and fixing Urinal of approved quality including connection

37 with trap and with integral longitudinal flush pipe. (A) Squating plate 5.00 1541.44 Each

pattern white earthenware 550mm x 300mm.

Providing and fixing to wall ceiling and floor 10.0 Kg. /Sqcm working

pressure polythelene pipes of the following outside diameter, low

density , complete with special flange compression type fitting wall

clipsetc. Making good wall ceiling and floor .(F) 75 mm Dia

(G)110 mm Dia 22.00 336.24 Rmt

Providing and Fixing S.W. Gully trap with C.I. grating brick masonry

chamber & water tight C.I Cover with frame of 300 mm x 300 mm

size (inside) with standard weight. [1] square mouth trap (B)

mm x 100 mm. size P or R -type

Constructing Brick Masonry Chamber for underground C.I inspection

chamber and bends with bricks having crushing strength not less than

35 kg/sqm in CM 1:5 C.I cover with frame (Light Duty) 455mm x

610mm internal dimension total weight of cover with frame to be not

less than 38 kg (Weight of cover 23 kg and weight of frame 15 kg) R.C.C

top slab with 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone

aggregate 20mm nominal size ) foundation concrete 1:5:10 inside

plaster 15mm thick with cement mortar 1:3 finished smooth

with a floating coat of neat cement on walls and bed concrete on

walls and bed concrete, excavation etc. complete. (I) Inside dimension

deep for single pipe

(II) Inside dimension 500mm x 700mm x 450mm

deep for pipeline one or two

Providing laying and jointing in true line and level following in dia.

U.P.V.C. Pipe (SCH - 40) line including fittings make PRINCE / SUPREME

/ ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge.

41 Pipe shall be fixed on the wall with the help of clamp at every two 28.00 72.65 Mtr

meter C/C or shall be concealed as directed including necessary fittings

etc. including testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials. (i)15 mm Dia

(ii)25mm Dia 49.00 91.84 Mtr

Providing and fixing screw down bib taps of following size.(B) Brass

chromium plated screws down bib taps (i) 15mm dia.

Providing and fixing gun metal check or non return wheel valve, 25 mm

Providing & laying ( to level or slopes ) and joining R.C.C. light duty NP2

44 CLASS Pipe In of following nominal internal diameters incl. Testing of

pipes and joints etc A )150 mm dia

B )250 mm dia 10.00 283.15 Rmt

C)300 mm dia 10.00 665.48 Rmt

Providing and fixing chromium plated brass half turn flushcock at all

45 floor level, of approved quality incl. fixing in pipe line etc. comp.(ii) 5.00 263.77 Each

Providing erecting and fixing double coated Syntex or equivalent PVC

46 (ISI) mark water tank of reqd capacity each with all necessary fitting 2000.00 3.95 litre

and connection etc. comp on terrace.

47 Providing and Fixing in position cowl vent to pipe

(B) 75 mm Pipe 2.00 389.74 Nos.

(C) 110 mm Pipe 4.00 501.87 Nos.

Electrification

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated

multi strand copper wires up to 10 mtr length , in below type of pipe

erected with 6A Modular type switch / bell push & accessories and

earth continuity of following type, erected on PVC / Metallic/Wooden

box, single mounting base frame covered with textured/metallic/white

front plate modules erected on / in wall / ceiling as per pipe erected,

with necessary Lamp holder/ceiling rose / H.D.Connector as

directed.(a) with medium class Rigid PVC pipe and accessories erected

flushed on wall/ceiling completeCat. III

Providing and erecting ISI mark Medium class RIGID PVC PIPES of

following size complete to be erected on/in wall or ceiling erected with

49 necessary PVC fittings & Junction boxes fixed with adhesive solution &

Clamps with following dia of pipes, in approved manner as directed

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI

marked stranded Copper conductor wire in following type of pipe to

be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm

50 copper conductor FRLS PVC insulated stranded wire of green colour for

earth continuity of following size (A) With medium class Rigid PVC pipe

and accessories (b) 2 wire 2.5 sq. mm

Supplying and erecting LED indoor fittings with LEDs of wattage

Watt to 0.5 Watt assembled on single MCPCB, with housing used as a

heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/ aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company mark/name 160V to

270V, Power Factor more than 0.95, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description

have shown ranges of Wattage capacity of LED fittings.The Engineer

incharge may select any wattage capacity between the ranges shown.)

(A) Tube Light with integral driver (iii) 18-20 Watts, Surge - 2KV,IP-20,

conventional 4 feet Cat-lll

Supplying and erecting led lamps with following wattage capacity of

220 to 240 voltage, minimum 15000 burning hours life, 500 V in built-

surge protection,Polycarbonate diffuser, mounting suitable for E14 /

E27 / B22 lamp holders, pf >=

(A) LED Lamps integral type, with PC diffuser suitable LAMP holder (ii)

5 to 8 watts Cat-III 14.00 111.00 112.11

Supplying and erecting LED street light / Flood light fittings with High

power White LEDs wattage of 3 Watt and above assembled on single

MCPCB, efficiency more than 130 lm/w and corrosion free High

pressure die cast aluminum housing with smooth finish powder coated

and heat sink extruded aluminium with diffuser and Polycarbonate

optics/ lenses, with toughened glass with company mark/name

engraved or embossed 160 to 270 V,Power Factor more than 0.95, THD

< 10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45, Luminaire

53 efficacy> 100 lumens/watt . LED driver efficiency > 85 %.( fittings

required LM-79 & LM-80 certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The Engineer incharge

may select any wattage capacity between the ranges shown.) (A) Street

Light (IP-65), Surge protection -4KV integral and ,Light must have

440VAC line supply with over-voltage protection. (iii) Above 60 to

providing and erecting Miniature circuit breaker single pole 6A to 25A

suitable to operate on 240 V A.C. system and having breaking capacity

54 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI

Providing & erecting 240 V MCB double pole switch for lighting Load (B

Curve) having 10 KA breaking capacity & confirms to IS : 8828 in

existing box having following capacity (B) 40 Amp.

Plastic enclosure fitted with DIN rail suitable for incorporating Three

/Four nos. MCB 1.00 107.00 108.07

Providing and erecting Sheet Steel powder coated MCB distribution

board - flush / surface mounted fitted with busbar, neutral link, earth

bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without

57 MCB to house appropriate nos. of MCBs.(The DBs should be used of

same company of MCB to be used) suitable for(b) sheet steel double

door (IP-43) (iii)8 way

providing and erecting Approved make RCCBs conforming to IS:

and having sensitivity of 30 mA and Short Circuit withstand capacity of

10 KA and suitable for operation on single phase 240 V,50Hz. having

58 characteristic of quick action & tripping with all advance feature & do

not incorporate any electronic component. for following Max. rating

erected as directed (ii) 40Amps. DP Cat. III

Supplying & erecting in earthpit of minimum bore dia. 225mm size

approved make Safe Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS 3043-1987 made of corrosion free hot dipped

G.I.Pipes having Outer pipe dia of 80 mm having 80-200 Micron

galvanising, Inner pipe dia of 40 mm having 200-250 Micron

galvanising, connection terminal dia of 14 mm with constant ohmic

value surrounded by highly conductive compound with high charge

dissipation suitable for following type of applications with chamber

and heavy duty cover.(approved make OEM has to submit test

certificate including value of earth resistane of installation.[A] For

electrical installation up to 440 V

Length of Pipe - 1 Mtr

Back filling compound - 1 Nos. of Bag of 15 Kgs.

Providing and erecting Annealed bare Copper wire 8 to 16 SWG.

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

Aluminium conductor for 1.1 KV. to be laid on wall with necessary

clamps or in existing trench / pipe of following size of cables. (A) 2 core

Providing and, fixing heavy duty flange type brass cable gland with

rubber ring for PVC insulated armoured cable complete with out going

tails, insulating tape etc for following size of cables.(A) 2 to 4 core 2.5 /

Solder less crimping type Aluminium lugs conforming to IS suitable for

cable of following size evenly crimped with high pressure tool &

63 connected to switchgear terminals with brass/cadmium plated nut

bolts in an approved manner. (A) 1.5/ 2.5/4/6 Sq.mm

Providing & erecting fresh air fan 250 mm dia with square frame make

of ABS body with louvers Cat.II 10.00 1544.00 1559.44

Total amount of Civil Work A

Total amount of Civil Work A

Total amount of watersupply & sanitry B

Total amount of watersupply & sanitry B

Total amount Electrification Work C

Total amount Electrification Work C

Add 2% Contigency Charges

Add 1% Q.C. Charges

SAY GRAND TOTAL

SAY GRAND TOTAL

SB-2 (Construction Work of Toilet Block in Vanzaravas)

ITEM OF WORK QTY Rate UNIT AMOUNT

Excavation for foundation upto 1.5 m depth including sorting out and

1 stacking of useful materials and disposing off the excavated stuff upto 31.00 117.08 Cu.m

All lead.(A) Loose or soft soil

Excavation for foundation for depth from 1.5 m to 3.0 m including

sorting out and stacking of useful materials and disposing off the

excavated stuff upto All lead.(A) Loose or soft soil

Filling available excavated earth (excluding rock)in trenches, plinth,

3 sides of foundations etc. in layers not exceeding 20cm in depth 53.00 130.39 Cu.m

consolidating each deposited layer by ramming & watering.

Filling in foundation and plinth with murrum or selected soil in layers of

4 20cm. thickness including watering, ramming and consolidating etc. 23.50 282.02 Cu.m

complete. (more than 10 ton)

Providing and laying cement concrete 1:2:4 (1- Cement : 2- Coarse sand

: 4- graded stone aggregates 20 mm nominal size) and curing complete

excluding cost of formwork in (A) Foundation and Plinth (more than

Providing and laying controlled cement concrete work M250 and curing

complete including the cost of form work but excluding the cost of

reinforcement of reinforced concrete work in foundation, footings base

of column and mass concrete. (A) Footing (more than 10 ton)

Providing and laying controlled cement concrete work M-25 and curing

complete including the cost of form work but excluding the cost of

reinforcement of reinforced concrete work in Column, Pillers, posts

and struts. (more than 10 Ton)

Providing and laying controlled cement concrete work M200 and curing

complete including the cost of form work and excluding the cost of

reinforcement of reinforced concrete work in : (B) Column (more than

Providing and laying controlled cement concrete work M250 and curing

complete including the cost of form work and excluding the cost of

reinforcement of reinforced concrete work in : (C) Ground Beam (more

Providing and laying controlled cement concrete work M200 and curing

complete including the cost of form work but excluding the cost of

reinforcement of reinforced concrete work in Lintel or Copping. (D)

Providing and laying controlled cement concrete work M200 and curing

complete including the cost of form work but excluding the cost of

reinforcement of reinforced concrete work in Chajja. (E) chhajja .

(more than 10 ton)

Providing and laying controlled cement concrete work M200 and curing

complete including the cost of form work but excluding the cost of

reinforcement of reinforced concrete work in Floor Beams. (F) floor

Beams. (more than 10 ton)

Providing and laying controlled cement concrete work M200 and curing

complete including the cost of form work but excluding the cost of

reinforcement of reinforced concrete work in Slabs.(G) slabs, landing,

shelves, balconies etc (more than 10 ton)

Providing TMT Bar FE 415 reinforcement for R.C.C. work including

13 bending, binding and placing in position complete upto floor two level 4150.00 67.26 Kg.

(more than 10 ton)

Brick work using common burnt clay building bricks having crushing

strength not less than 35 kg./Sq.Cm. in foundation and plinth in

Cement Mortar 1:6 (1- Cement : 6 -fine sand) (B) Conventional (more

(i) Half brick masonry in common brunt clay building bricks having

crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1-

Cement : 4 -coarse sand ) in foundation and plinth (B) Conventional

(more than 10 ton)

Providing 15mm. thick cement plaster in single coat on rough (similar)

side of single or half brick walls for interior plastering up to floor two

level finished even and smooth in cement mortar 1:4 [1 cement:

sand) etc. complet

Providing & laying10 mm. thick cement plaster in single coat on fair

side of brick concrete walls & ceilings for interior plastering upto floor

two level and finishing with smooth mala plaster.(i) Cement mortar 1:3

(1 cement : 3 sand)

20 mm thick sand faced cement plaster on wall upto hight

metres above ground level consisting of 12mm thick backing coat of

c.m. 1 :3 (1 cement : 3 sand) and 8 mm thick finishing coat of c.m. 1 :

1 (1 cement : 1 sand) etc. complete

Providing throating or plaster drip and moulding to R.C.C. Chajja

Providing & Laying 24" x 24" vitrified 8 mm thick tile flooring over

mm (average) base of cement mortar 1:6 ( 1 cement: 6 coarse sand) on

20 new surface or fixing on existing flooring by adhesive material including 45.00 1397.83 Sqm

dismentaling of xisting flooring and jointed with color cement slurry

including finised with flush pointing & cleanin

Providing and laying light shade vitrified tiles 8mm to 10mm thick in

skirting,risers of steps and dedo on 10mm thick cement plaster

1:3 (1 cement : 3 Coarse sand) & jointed with white cement slurry for

light shed satin finish/Semi glossy.

Providing and laying polished kota stone slab flooring over

mm.(average) thick base of cement mortar 1:6 (1 cement : 6 coarse

sand) or L.M. 1:1.5 laid over and jointed with gray cement slurry

including rubbing & polishing etc. complete. [A] 25mm

Providing and laying polished Granite Slab 18mm thick in Risers of

steps Dedo, window sill, jembs and pillars laid 10mm thick Cement

23 Mortar 1:4 (1-Cement : 4-Coarse Sand) and jointed with Grey Cement 7.00 2990.00 Sqm

Slurry including full molded round front edges , rubbing and polishing

Providing and fixing flush door with I.T.W. beading all around by using

I.T.W. frame 100 m.m. x 70m.m.. shutter fabricated from 35 mm thick

solid core non decorative flush door exterior grade bonded BWP/BWR

synthetic resin having stamped IS 12823 grade I type II including

24 priming coat & two coats of painting on surfaces and Stainless steel 4.50 3129.99 Sqm

decorative type designs fixtures / fastening 2Nos. Handles, 2Nos.

Aldropes, towerbolt etc.including I.T.W. triangular batten patti of size

30m.m.x30m.m.etc. as per architectural detailed drawing and as

directed by engineer in charge.

Providing and fixing FRP FRAME size 100 x 50mm and 28mm thick FRP

depress pannel shutter having extra reinforcement on sides and edges

and in gel coat finish. The core of the shutter is to be filled up with

injected fire retardent grade polyurethane foam done in situ along with

embedded wooden places for stiffening and also for tacking hinges and

fixture. The hole FRP frame and shutter is to be water proof, water

proof, termite proof and resistance to mild acid/Alkali. Rates are to be

inclusive of S.S hinges with necessary screws and Alluminium fixture

and fastening.Product should have 3 years prefomance guarantee and

company have ISO 9001-2000 certificate.

Providing & fixing standard extructed of alluminium section of size

63mm x 38.10 mm x12 mm (jindal section 2434 @ wt..643 kg/mt.) with

colour anodized alluminium frame for ventilation with 5 mm thick

frosted glass as details etc.complete for Ventilation

Providing and fixing M.S. Gate of required pattern to marble/ granite

frames of window etc. with M.s. flats at required spacing and frames

alround, square or round bars fixed with round headed bolts and nuts

or by screws, including oil painting with one coat of primer of approved

quality and brand & two coats of synthetic enamal oil paint etc.

complete as per detail drawing and as directed by Engineer in charge.

Finishing wall with weather proof exterior emulsion paint on wall

surface (two coats) to give an required shape even shade after

thoroughly brushing the surface to remove all dirt, and remains of

loose powdered materials.etc complete

Applying two coats of Birla or Asian acrylic lappy (putty) and two coats

of primer of approved brand and manufacture on new wall surface to

give an even shade including thoroughly brushing the surface free from

mortar dropping and other foreign matter and sand prepared smooth.

and Wall painting (two coats) with plastic emulsion paint of approved

brand and manufacture on undecorated wall surface to give an even

shade including throughly brushing the surface free from mortar

droppings and other foreign matter and sand papered smooth.

Providing and laying China Mosaic type water proofing treatment on

terrace including (a) Applying neat cement slurry 2.75 Kg./Smt. of

cement admix with water proofing compound after cleaning the

surface (b) 50 mm thk. Cement Concrete flooring 1:2:4 (1-Cement : 2-

Coarse sand : 4-graded stone aggregate 20 mm nominal size) laid in

admixed with water proofing compound including rounding of

junctions of walls and slabs (c) after two days of proper curing applying

a second coat of cement slurry (d) finishing the surface with 20mm

thick cement mortar 1:4 (1 cement : 4 coarse sand) and china mosaic

tilling & finally finishing the surface with trowel with white cement

slurry (e) after finishing the whole terrace shall be flooded with water

for a period of two weeks.

Carrying out plinth treatment to post constrution/existing structrue by

spraying chemical solution for termite control treatment including

labour and material consistent with I.S.I specification. Using chloride

and Chiorpurfiles 20 EC. Asper 6131_ paret-II Consentration Weight

one percent is recommended i.e. one litre 20 EC chemical emulsion

with 19 litre give 1% concentration inclusive of one litre chemical

emulsion application at the rate of 5 litre chemical/sqmt. of surface is

recommended as per I.S.

WATER SUPPLY AND SANITATION

Providing & fixing water closet squatting pan ( Orrisa type W.C. pan)

size 580 mm including 100 mm P or S trap for water closet squatting

32 pan incl. jointing the trap with the pan & soil pipe in cement mortar 5.00 933.78 Each

1:1(1 cement : 1 fine sand)(including earthwork, bed concrete, foot

ress and trap) (A) Vitreous China : (i) long pattern white colour

Providing and fixing wash down water closet (european type W C pan)

with integral P and S trap including jointing the trap with soil pipe in

cement mortar 1:1 ( 1 cement fine sand) including Providing and fixing

Plastic Seat and cover for wash down water closet with C.P. brass

hinges and rubber buffers and also includes provide and fixing jet wash

Facilities complete

(A)Vitereous China Pattern:

(I) in White Colour

Providing and fixing washbasin with single hole for pillar trap at all floor

level with C.I. or M.S. Brackets painted white including cutting holes

and making good the same (A) Vitreous china flat back wash basin

550mm x 400mm size in white colour including (a) providing and fixing

34 C.P. brass waste for wash basin or sink(A) 32mm (b) providing and 4.00 2115.16 Each

fixing M.I.fisher union for wash basin or sink(A) 32mm (c) piller

tap,capstan head, screw down high pressurewith screw shanks and

back nuts for 15mm dia. for all floor (d)brass screw down stop tap

Providing & fixing 600 mm. x 450 mm. bevelled edge mirror of superior

glass at all floor levels, mounted on 6 mm. th. A.C. sheet or plywood

sheet & fixed to wooden plugs with C.P. brass screws and washers etc.

Providing and fixing PVC SWR Nanhi trap IS 14735 for drain -100 mm

diameter with jali of the following nominal diameter of self cleaning

design with C.I scead down or hinged grating including the cost of

cutting and making good the wall.

Providing and fixing Urinal of approved quality including connection

37 with trap and with integral longitudinal flush pipe. (A) Squating plate 5.00 1541.44 Each

pattern white earthenware 550mm x 300mm.

Providing and fixing to wall ceiling and floor 10.0 Kg. /Sqcm working

pressure polythelene pipes of the following outside diameter, low

density , complete with special flange compression type fitting wall

clipsetc. Making good wall ceiling and floor .(F) 75 mm Dia

(G)110 mm Dia 22.00 336.24 Rmt

Providing and Fixing S.W. Gully trap with C.I. grating brick masonry

chamber & water tight C.I Cover with frame of 300 mm x 300 mm

size (inside) with standard weight. [1] square mouth trap (B)

mm x 100 mm. size P or R -type

Constructing Brick Masonry Chamber for underground C.I inspection

chamber and bends with bricks having crushing strength not less than

35 kg/sqm in CM 1:5 C.I cover with frame (Light Duty) 455mm x

610mm internal dimension total weight of cover with frame to be not

less than 38 kg (Weight of cover 23 kg and weight of frame 15 kg) R.C.C

top slab with 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone

aggregate 20mm nominal size ) foundation concrete 1:5:10 inside

plaster 15mm thick with cement mortar 1:3 finished smooth

with a floating coat of neat cement on walls and bed concrete on

walls and bed concrete, excavation etc. complete. (I) Inside dimension

deep for single pipe

(II) Inside dimension 500mm x 700mm x 450mm

deep for pipeline one or two

Providing laying and jointing in true line and level following in dia.

U.P.V.C. Pipe (SCH - 40) line including fittings make PRINCE / SUPREME

/ ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge.

41 Pipe shall be fixed on the wall with the help of clamp at every two 28.00 72.65 Mtr

meter C/C or shall be concealed as directed including necessary fittings

etc. including testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials. (i)15 mm Dia

(ii)25mm Dia 49.00 91.84 Mtr

Providing and fixing screw down bib taps of following size.(B) Brass

chromium plated screws down bib taps (i) 15mm dia.

Providing and fixing gun metal check or non return wheel valve, 25 mm

Providing & laying ( to level or slopes ) and joining R.C.C. light duty NP2

44 CLASS Pipe In of following nominal internal diameters incl. Testing of

pipes and joints etc A )150 mm dia

B )250 mm dia 10.00 283.15 Rmt

C)300 mm dia 10.00 665.48 Rmt

Providing and fixing chromium plated brass half turn flushcock at all

45 floor level, of approved quality incl. fixing in pipe line etc. comp.(ii) 5.00 263.77 Each

Providing erecting and fixing double coated Syntex or equivalent PVC

46 (ISI) mark water tank of reqd capacity each with all necessary fitting 2000.00 3.95 litre

and connection etc. comp on terrace.

47 Providing and Fixing in position cowl vent to pipe

(B) 75 mm Pipe 2.00 389.74 Nos.

(C) 110 mm Pipe 4.00 501.87 Nos.

Electrification

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated

multi strand copper wires up to 10 mtr length , in below type of pipe

erected with 6A Modular type switch / bell push & accessories and

earth continuity of following type, erected on PVC / Metallic/Wooden

box, single mounting base frame covered with textured/metallic/white

front plate modules erected on / in wall / ceiling as per pipe erected,

with necessary Lamp holder/ceiling rose / H.D.Connector as

directed.(a) with medium class Rigid PVC pipe and accessories erected

flushed on wall/ceiling completeCat. III

Providing and erecting ISI mark Medium class RIGID PVC PIPES of

following size complete to be erected on/in wall or ceiling erected with

49 necessary PVC fittings & Junction boxes fixed with adhesive solution &

Clamps with following dia of pipes, in approved manner as directed

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI

marked stranded Copper conductor wire in following type of pipe to

be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm

50 copper conductor FRLS PVC insulated stranded wire of green colour for

earth continuity of following size (A) With medium class Rigid PVC pipe

and accessories (b) 2 wire 2.5 sq. mm

Supplying and erecting LED indoor fittings with LEDs of wattage

Watt to 0.5 Watt assembled on single MCPCB, with housing used as a

heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/ aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company mark/name 160V to

270V, Power Factor more than 0.95, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description

have shown ranges of Wattage capacity of LED fittings.The Engineer

incharge may select any wattage capacity between the ranges shown.)

(A) Tube Light with integral driver (iii) 18-20 Watts, Surge - 2KV,IP-20,

conventional 4 feet Cat-lll

Supplying and erecting led lamps with following wattage capacity of

220 to 240 voltage, minimum 15000 burning hours life, 500 V in built-

surge protection,Polycarbonate diffuser, mounting suitable for E14 /

E27 / B22 lamp holders, pf >=

(A) LED Lamps integral type, with PC diffuser suitable LAMP holder (ii)

5 to 8 watts Cat-III 14.00 111.00 112.11

Supplying and erecting LED street light / Flood light fittings with High

power White LEDs wattage of 3 Watt and above assembled on single

MCPCB, efficiency more than 130 lm/w and corrosion free High

pressure die cast aluminum housing with smooth finish powder coated

and heat sink extruded aluminium with diffuser and Polycarbonate

optics/ lenses, with toughened glass with company mark/name

engraved or embossed 160 to 270 V,Power Factor more than 0.95, THD

< 10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45, Luminaire

53 efficacy> 100 lumens/watt . LED driver efficiency > 85 %.( fittings

required LM-79 & LM-80 certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The Engineer incharge

may select any wattage capacity between the ranges shown.) (A) Street

Light (IP-65), Surge protection -4KV integral and ,Light must have

440VAC line supply with over-voltage protection. (iii) Above 60 to

providing and erecting Miniature circuit breaker single pole 6A to 25A

suitable to operate on 240 V A.C. system and having breaking capacity

54 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI

Providing & erecting 240 V MCB double pole switch for lighting Load (B

Curve) having 10 KA breaking capacity & confirms to IS : 8828 in

existing box having following capacity (B) 40 Amp.

Plastic enclosure fitted with DIN rail suitable for incorporating Three

/Four nos. MCB 1.00 107.00 108.07

Providing and erecting Sheet Steel powder coated MCB distribution

board - flush / surface mounted fitted with busbar, neutral link, earth

bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without

57 MCB to house appropriate nos. of MCBs.(The DBs should be used of

same company of MCB to be used) suitable for(b) sheet steel double

door (IP-43) (iii)8 way

providing and erecting Approved make RCCBs conforming to IS:

and having sensitivity of 30 mA and Short Circuit withstand capacity of

10 KA and suitable for operation on single phase 240 V,50Hz. having

58 characteristic of quick action & tripping with all advance feature & do

not incorporate any electronic component. for following Max. rating

erected as directed (ii) 40Amps. DP Cat. III

Supplying & erecting in earthpit of minimum bore dia. 225mm size

approved make Safe Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS 3043-1987 made of corrosion free hot dipped

G.I.Pipes having Outer pipe dia of 80 mm having 80-200 Micron

galvanising, Inner pipe dia of 40 mm having 200-250 Micron

galvanising, connection terminal dia of 14 mm with constant ohmic

value surrounded by highly conductive compound with high charge

dissipation suitable for following type of applications with chamber

and heavy duty cover.(approved make OEM has to submit test

certificate including value of earth resistane of installation.[A] For

electrical installation up to 440 V

Length of Pipe - 1 Mtr

Back filling compound - 1 Nos. of Bag of 15 Kgs.

Providing and erecting Annealed bare Copper wire 8 to 16 SWG.

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

Aluminium conductor for 1.1 KV. to be laid on wall with necessary

clamps or in existing trench / pipe of following size of cables. (A) 2 core

Providing and, fixing heavy duty flange type brass cable gland with

rubber ring for PVC insulated armoured cable complete with out going

tails, insulating tape etc for following size of cables.(A) 2 to 4 core 2.5 /

Solder less crimping type Aluminium lugs conforming to IS suitable for

cable of following size evenly crimped with high pressure tool &

63 connected to switchgear terminals with brass/cadmium plated nut

bolts in an approved manner. (A) 1.5/ 2.5/4/6 Sq.mm

Providing & erecting fresh air fan 250 mm dia with square frame make

of ABS body with louvers Cat.II 10.00 1544.00 1559.44

Total amount of Civil Work A

Total amount of Civil Work A

Total amount of watersupply & sanitry B

Total amount of watersupply & sanitry B

Total amount Electrification Work C

Total amount Electrification Work C

Add 2% Contigency Charges

Add 1% Q.C. Charges

SAY GRAND TOTAL

SAY GRAND TOTAL

SB-3 (Repairing Work of Toilet Block Near Maharnapratap Circle Nadiad Highway)

Description Qty. Rate Unit Amount

Removing and scraping of old deteriorated plaster of any thickness

fromm wall / R.C.C member including stacking of serviceable material

and disposal of unserviceable from site of work with all lead and lift

Dismantling santtary fittings like wash basin. W.C. pan Indian and

2 European type, flushing tank etc. including stacking the materials with 10.00 394.51 Each

all lead and lift.

Dismentling doors, windows, ventilators etc. (wood or steel) shutters

including chowkhats architraves, holdfasts and other attachment etc.

complete and stacking them within all lead and lift.(ii) Exceeding

Dismentaling tiled of stone floors laid in mortar including stacking of

4 serviceable materilas and disposal of unserviceable materials with all 17.50 46.77 Sq.M

Providing and fixing M.S. grills of required pattern to wooden frames of

windows etc. with M.S. flats at required spacings and frame alround,

square or round bars with round headed bolts and nuts or by screws.

(B) ORNAMENTAL GRILL

Providing and fixing M.S. grills of required pattern to wooden frames of

windows etc. with M.S. flats at required spacings and frame alround,

square or round bars with round headed bolts and nuts or by screws

(A) Plain Grill.

Providing 10mm thick cement plaster in single coat on brick /concrete

walls for interior plastering upto floor two level and finished even and

smooth in (iii) Cement mortar 1:6 (1-cement:6-sand) and finishing with

a floating coat of neat cement slurry.

20mm thick sand faced cement plaster on walls upto height 10 metres

above ground level consisting of 12mm thick backing coat of C.M. 1:3

(1-cement : 3-sand) and 8mm thick finishing coat of C.M. 1:1 (1-cement

: 1-sand) etc. complete.

Providing and laying Ceramic tiles 6mm thick in flooring treads of steps

9 and landing laid on a bed of 12mm thick cement mortar 1:3 (1-cement : 124.00 949.68 Sq.M

3-coarse sand) finishing with flush pointing in white cement.

P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm (average)

base of cement mortar 1:6 ( 1 cement: 6 coarse sand) on new surface

or fixing on existing flooring by adhesive material including

dismentaling of existing flooring and jointed with color cement slurry

including finised with flush pointing & cleaning the surface etc.

complete for light shade

Providing and fixing water closet squatting Pan (Indian type W.C. Pan)

size 580mm (Earthwork, bed concrete, foot reste and trap to be

measured and paid for separately) (A) Vitreous China.(I) Long pattern =

Providing and fixing Urinal or approved quality including conecting the

12 Urinal with waste pipe, tap etc.complete.(A) White earthenware flat 2.00 1036.27 Each

back or corner type size 430mm x 260mm x 350mm.

Providing laying and jointing in true line and level 25mm dia. U.P.V.C.

Pipe (SCH - 40) for cold water including fittings as approved by Engineer

In Charge. Pipe shall be fixed on the wall with the help of clamp at

every two metre C/C or shall be concealed as directed including

necessary fittings etc. including testing of pipe and joints and fixing the

same with adhesive solvent including cost of all materials.

Providing and fixing washbasin with single hole for pillar trap at all floor

level with C.I. or M.S. Brackets painted white including cutting holes

and making good the same (A) Vitreous china flat back wash basin

550mm x 400mm size in white colour including (a) providing and fixing

14 C.P. brass waste for wash basin or sink(A) 32mm (b) providing and 4.00 2115.16 Each

fixing M.I.fisher union for wash basin or sink(A) 32mm (c) piller

tap,capstan head, screw down high pressurewith screw shanks and

back nuts for 15mm dia. for all floor (d)brass screw down stop tap

Constructing brick masonry chamber for underground C.I. Inspection

chamber and bends with bricks having crushing strength not less than

35Kg/Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x

610mm intenal dimensions total weight of cover with frame to be not

less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg.) (R.C.C.

top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone

aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm

thick with cement mortar 1:3 finished smooth with a floating coat of

neat cement on walls and bed concrete etc. complete. (i) Inside

dimensions 455mmx 610mm and 450mm deep for single pipe line.

Providing and fixing chromium plated brass half turn flush cock of

16 approved quality including fixing in pipe line etc. complete.(ii) 25mm 2.00 263.77 Each

Providing erecting and fixing double coated ISI water tank of required

17 capacity each with all necessary fittings and connection etc. complete 1000.00 3.95 Litre

18 Providing and fixing brass screw down stop tap. (A) 15mm dia. 15.00 205.83 Each

Distempeing (Two coats) with oil bound distemper of approved brand

and manufacture and of required shade on wall surfaces to give an

even shade, over and including a priming coat with distemper primer of

approved brand and manufacture after thoroughly brushing the

surface free from mortar dropping and other foreign matter and also

including preparing the surface even and sand papered smooth.

Providing laying and jointing in true line and level 15mm dia. U.P.V.C.

Pipe (SCH-40) for cold water including fittings as approved by Engineer

In Charge. Pipe shall be fixed on the wall with the help of clamp at

20 every two metre C/C or shall be concealed as directed including 30.00 72.65 Rmt

necessary fittings etc. including testing of pipe and joints and fixing the

same with adhesive solvent, including cost of all materials.

Providing laying (to level or slopes) and jointing reinforced concrete

Light duty non-pressure pipes I.S. class NP2 of the following internal

21 diameter with collars and butt ends prepared for collar joints including 50.00 240.21 Rmt

testing of joints complete.(B) 150mm

Point wiring for Light with 2-1.5 sq.mm & earth wire of 1.5 sq.mm

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length, in below type of pipe erected

with 6A Modular type switch / bell push & accessories and earth

continuity of following type, erected on PVC / Metallic/Wooden box,

single mounting base frame covered with textured/metallic/white

front plate modules erected on / in wall / ceiling as per pipe erected,

with necessary Lamp holder/ceiling rose / H.D.Connector as directed.

[Refer measurment sheet ]

with medium class Rigid PVC pipe and accessories erected concealed

in wall/ceiling complete (Cat-III)

Providing and erecting ISI mark Medium class RIGID PVC PIPES of

following size complete to be erected on/in wall or ceiling erected with

necessary PVC fittings & Junction boxes fixed with adhesive solution &

Clamps with following dia of pipes, in approved manner as directed,

(Make:precison, nihir, polycab, vraj)

Supplying and erecting LED indoor fittings with LEDs of wattage

Watt to 0.5 Watt assembled on single MCPCB, with housing used as a

heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/ aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company mark/name 160V to

270V, Power Factor more than 0.95, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description

have shown ranges of Wattage capacity of LED fittings.The Engineer

incharge may select any wattage capacity between the ranges

shown.)(A) Tube Light/Surface light with integral driver 18-20 Watts,

Surge-2KV, IP-20, conventional 4 feet- Cat-III

POWER CABLES -1.1 kV Grade Cable- Aluminium /Copper Conductor

with accessories :-

Design, engineering, procurement, installation, testing and

commissioning of 1.1 kV grade, XLPE insulated, stranded Aluminium

conductor, galvanised steel flat strip / round wire armoured, extruded

PVC type ST2 sheathed, heavy duty cable (to be laid on wall surface

with necessary clamps / in existing cable trench / cable trays / conduit /

pipe sleeves at road crossing or floor as per site requirement)

conforming to IS:7098 (Part-1) & IEC:60502 (Part-1) of following sizes:

(a) For GEB transformer to LVDB/PCC panel , 3.5 C x 35 Sq. mm Al.

(d) -DO- for Providing and erecting Mains with 1.1 KV grade FRLS PVC

insulated ISI marked stranded Copper conductor wire in following type

of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq.

mm copper conductor FRLS PVC insulated stranded wire of green

colour for earth continuity of following size With medium class Rigid

PVC pipe and accessories

For all DB Connection & Light connection 2 wire 2.5 sq. mm

Providing and laying China Mosaic type water proofing treatment on

terrace including (a) Applying neat cement slurry 2.75 Kg./Smt. of

cement admix with water proofing compound after cleaning the

surface (b) 50 mm thk. Cement Concrete flooring 1:2:4 (1-Cement : 2-

Coarse sand : 4-graded stone aggregate 20 mm nominal size) laid in

admixed with water proofing compound including rounding of

26 junctions of walls and slabs (c) after two days of proper curing applying 75.50 1094.56 Sq.M

a second coat of cement slurry (d) finishing the surface with 20mm

thick cement mortar 1:4 (1 cement : 4 coarse sand) and china mosaic

tilling & finally finishing the surface with trowel with white cement

slurry (e) after finishing the whole terrace shall be flooded with water

for a period of two weeks.

Demolition of Brick work and stone masonry including stacking of

serviceable materilas and disposal of unserviceable materials with all

lead and lift. (i) In Lime Mortar.

Excavation for foundation upto 1.5 m depth including sorting out and

28 stacking of useful materials and disposing off the excavated stuff upto 2.50 117.08 Cu.M

50 Meter lead. (A) Loose or soft soil

Providing and laying cement concrete 1:4:8 (1- Cement : 4- coarse sand

: 8- hand broken stone aggregates 40 mm nominal size) and curing

complete excluding cost of formwork in (A) Foundation and Plinth

Brick work using common burnt clay building bricks having crushing

strength not less than 35 kg./Sq.Cm. in foundation and plinth in

Cement Mortar 1:5. (1- Cement : 5 -fine sand) (B) Conventional

Providing 15mm thick cement plaster in single coat on Rough

(Similar)side of single or half brick walls for interior plastering upto

floor two level and finished even and smooth in (i) Cement mortar 1:3

(1-cement:3-sand)

Finishing Various wall Painting with weather proof exterior emulsion

paint on wall surface (two coats) to give an required shape even shade

32 after thoroughly brushing the surface to remove all dirt, and remains of 64.56 80.80 Sq.ft

loose powdered materials. etc complete.

Finishing wall with water proofing cement paint of on wall surfaces

(Two coats) to give an approved brand and manufacture and of

33 required shape even shade after thoroughly brushing the surface to 16.50 Sq.M 57.27

remove all dirt and remains of loose powered materials.

Providing & Applying Art work painting. It shall be water proof and

capable bridging, crazing and cracks, paint of makes as per approval.

Item including surface, applying one coat of primer coat shall not be

34 less then 50 micron and make listed in the tender and also including all 54.00 Sq.F 95.95

types of scafloding, safety accessories, labour, all materials lead as per

directed by engineer in charge.

Supplying & erecting approved make self-priming domestic monoblock

water pump with 0.5 H.P. motor, suitable for operation on 230 volts

c/s. AC supply with metallic flange, delivery and discharge of 32 LPM

at 10 mtrs.head.

Providing and fixing flush door with I.T.W. beading all around by using

I.T.W. frame 100 m.m. x 70m.m.. shutter fabricated from 35 mm thick

solid core non decorative flush door exterior grade bonded BWP/BWR

synthetic resin having stamped IS 12823 grade I type II including

36 priming coat & two coats of painting on surfaces and Stainless steel 17.33 Smt 3129.99

decorative type designs fixtures / fastening 2Nos. Handles, 2Nos.

Aldropes, towerbolt etc.including I.T.W. triangular batten patti of size

30m.m.x30m.m.etc. as per architectural detailed drawing and as

directed by engineer in charge..

Providing and fixing 600mm x 450mm bevelled edge mirrror of

37 superior glass mounted on 6mm thick A.C. sheet or plywood sheet and 2.00 Each 859.41

fixing to wooden pluge with C.P. brass screws and washers.

Supplying & erecting approved make low noise decorative exhaust fan

38 having square frame ABS body with inbuilt lowers & square frame. 10.00 No 1703.87

200mm with 1350RPM Cat.II

Providing window frame suitable for erection of Exhaust fan complete

39 covering the remaining portion of window with 15 mm. thick plywood 10.00 Ea 172.71

and colour washing to match the colour of the wall.

Providing and laying polished Granite Slab 18mm thick in Risers of

steps Dedo, window sill, jembs and pillars laid 10mm thick Cement

40 Mortar 1:4 (1-Cement : 4-Coarse Sand) and jointed with Grey Cement 19.00 Smt 2990.00

Slurry including full molded round front edges , rubbing and polishing

Add GST 18% Amount Rs.

Total Amount Rs.

Total Amount Rs.

Survaying,planing, Estimation, and Supervision charges @2.00 %

Total Amount Rs.

Total Amount Rs.

SB-4 (Repairing Work of Toilet Block in Sardar market)

Description Qty. Rate Unit Amount

Removing and scraping of old deteriorated plaster of any thickness

fromm wall / R.C.C member including stacking of serviceable material

and disposal of unserviceable from site of work with all lead and lift

Dismantling santtary fittings like wash basin. W.C. pan Indian and

2 European type, flushing tank etc. including stacking the materials with 10.00 394.51 Each

all lead and lift.

Dismentling doors, windows, ventilators etc. (wood or steel) shutters

including chowkhats architraves, holdfasts and other attachment etc.

complete and stacking them within all lead and lift.(ii) Exceeding

Dismentaling tiled of stone floors laid in mortar including stacking of

4 serviceable materilas and disposal of unserviceable materials with all 17.50 46.77 Sq.M

Providing and fixing M.S. grills of required pattern to wooden frames of

windows etc. with M.S. flats at required spacings and frame alround,

square or round bars with round headed bolts and nuts or by screws.

(B) ORNAMENTAL GRILL

Providing and fixing M.S. grills of required pattern to wooden frames of

windows etc. with M.S. flats at required spacings and frame alround,

square or round bars with round headed bolts and nuts or by screws

(A) Plain Grill.

Providing 10mm thick cement plaster in single coat on brick /concrete

walls for interior plastering upto floor two level and finished even and

smooth in (iii) Cement mortar 1:6 (1-cement:6-sand) and finishing with

a floating coat of neat cement slurry.

20mm thick sand faced cement plaster on walls upto height 10 metres

above ground level consisting of 12mm thick backing coat of C.M. 1:3

(1-cement : 3-sand) and 8mm thick finishing coat of C.M. 1:1 (1-cement

: 1-sand) etc. complete.

Providing and laying Ceramic tiles 6mm thick in flooring treads of steps

9 and landing laid on a bed of 12mm thick cement mortar 1:3 (1-cement : 124.00 949.68 Sq.M

3-coarse sand) finishing with flush pointing in white cement.

P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm (average)

base of cement mortar 1:6 ( 1 cement: 6 coarse sand) on new surface

or fixing on existing flooring by adhesive material including

dismentaling of existing flooring and jointed with color cement slurry

including finised with flush pointing & cleaning the surface etc.

complete for light shade

Providing and fixing water closet squatting Pan (Indian type W.C. Pan)

size 580mm (Earthwork, bed concrete, foot reste and trap to be

measured and paid for separately) (A) Vitreous China.(I) Long pattern =

Providing and fixing Urinal or approved quality including conecting the

12 Urinal with waste pipe, tap etc.complete.(A) White earthenware flat 2.00 1036.27 Each

back or corner type size 430mm x 260mm x 350mm.

Providing laying and jointing in true line and level 25mm dia. U.P.V.C.

Pipe (SCH - 40) for cold water including fittings as approved by Engineer

In Charge. Pipe shall be fixed on the wall with the help of clamp at

every two metre C/C or shall be concealed as directed including

necessary fittings etc. including testing of pipe and joints and fixing the

same with adhesive solvent including cost of all materials.

Providing and fixing washbasin with single hole for pillar trap at all floor

level with C.I. or M.S. Brackets painted white including cutting holes

and making good the same (A) Vitreous china flat back wash basin

550mm x 400mm size in white colour including (a) providing and fixing

14 C.P. brass waste for wash basin or sink(A) 32mm (b) providing and 4.00 2115.16 Each

fixing M.I.fisher union for wash basin or sink(A) 32mm (c) piller

tap,capstan head, screw down high pressurewith screw shanks and

back nuts for 15mm dia. for all floor (d)brass screw down stop tap

Constructing brick masonry chamber for underground C.I. Inspection

chamber and bends with bricks having crushing strength not less than

35Kg/Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x

610mm intenal dimensions total weight of cover with frame to be not

less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg.) (R.C.C.

top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone

aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm

thick with cement mortar 1:3 finished smooth with a floating coat of

neat cement on walls and bed concrete etc. complete. (i) Inside

dimensions 455mmx 610mm and 450mm deep for single pipe line.

Providing and fixing chromium plated brass half turn flush cock of

16 approved quality including fixing in pipe line etc. complete.(ii) 25mm 2.00 263.77 Each

Providing erecting and fixing double coated ISI water tank of required

17 capacity each with all necessary fittings and connection etc. complete 1000.00 3.95 Litre

18 Providing and fixing brass screw down stop tap. (A) 15mm dia. 15.00 205.83 Each

Distempeing (Two coats) with oil bound distemper of approved brand

and manufacture and of required shade on wall surfaces to give an

even shade, over and including a priming coat with distemper primer of

approved brand and manufacture after thoroughly brushing the

surface free from mortar dropping and other foreign matter and also

including preparing the surface even and sand papered smooth.

Providing laying and jointing in true line and level 15mm dia. U.P.V.C.

Pipe (SCH-40) for cold water including fittings as approved by Engineer

In Charge. Pipe shall be fixed on the wall with the help of clamp at

20 every two metre C/C or shall be concealed as directed including 30.00 72.65 Rmt

necessary fittings etc. including testing of pipe and joints and fixing the

same with adhesive solvent, including cost of all materials.

Providing laying (to level or slopes) and jointing reinforced concrete

Light duty non-pressure pipes I.S. class NP2 of the following internal

21 diameter with collars and butt ends prepared for collar joints including 50.00 240.21 Rmt

testing of joints complete.(B) 150mm

Point wiring for Light with 2-1.5 sq.mm & earth wire of 1.5 sq.mm

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length, in below type of pipe erected

with 6A Modular type switch / bell push & accessories and earth

continuity of following type, erected on PVC / Metallic/Wooden box,

single mounting base frame covered with textured/metallic/white

front plate modules erected on / in wall / ceiling as per pipe erected,

with necessary Lamp holder/ceiling rose / H.D.Connector as directed.

[Refer measurment sheet ]

with medium class Rigid PVC pipe and accessories erected concealed

in wall/ceiling complete (Cat-III)

Providing and erecting ISI mark Medium class RIGID PVC PIPES of

following size complete to be erected on/in wall or ceiling erected with

necessary PVC fittings & Junction boxes fixed with adhesive solution &

Clamps with following dia of pipes, in approved manner as directed,

(Make:precison, nihir, polycab, vraj)

Supplying and erecting LED indoor fittings with LEDs of wattage

Watt to 0.5 Watt assembled on single MCPCB, with housing used as a

heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/ aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company mark/name 160V to

270V, Power Factor more than 0.95, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description

have shown ranges of Wattage capacity of LED fittings.The Engineer

incharge may select any wattage capacity between the ranges

shown.)(A) Tube Light/Surface light with integral driver 18-20 Watts,

Surge-2KV, IP-20, conventional 4 feet- Cat-III

POWER CABLES -1.1 kV Grade Cable- Aluminium /Copper Conductor

with accessories :-

Design, engineering, procurement, installation, testing and

commissioning of 1.1 kV grade, XLPE insulated, stranded Aluminium

conductor, galvanised steel flat strip / round wire armoured, extruded

PVC type ST2 sheathed, heavy duty cable (to be laid on wall surface

with necessary clamps / in existing cable trench / cable trays / conduit /

pipe sleeves at road crossing or floor as per site requirement)

conforming to IS:7098 (Part-1) & IEC:60502 (Part-1) of following sizes:

(a) For GEB transformer to LVDB/PCC panel , 3.5 C x 35 Sq. mm Al.

(d) -DO- for Providing and erecting Mains with 1.1 KV grade FRLS PVC

insulated ISI marked stranded Copper conductor wire in following type

of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq.

mm copper conductor FRLS PVC insulated stranded wire of green

colour for earth continuity of following size With medium class Rigid

PVC pipe and accessories

For all DB Connection & Light connection 2 wire 2.5 sq. mm

Providing and laying China Mosaic type water proofing treatment on

terrace including (a) Applying neat cement slurry 2.75 Kg./Smt. of

cement admix with water proofing compound after cleaning the

surface (b) 50 mm thk. Cement Concrete flooring 1:2:4 (1-Cement : 2-

Coarse sand : 4-graded stone aggregate 20 mm nominal size) laid in

admixed with water proofing compound including rounding of

26 junctions of walls and slabs (c) after two days of proper curing applying 75.50 1094.56 Sq.M

a second coat of cement slurry (d) finishing the surface with 20mm

thick cement mortar 1:4 (1 cement : 4 coarse sand) and china mosaic

tilling & finally finishing the surface with trowel with white cement

slurry (e) after finishing the whole terrace shall be flooded with water

for a period of two weeks.

Demolition of Brick work and stone masonry including stacking of

serviceable materilas and disposal of unserviceable materials with all

lead and lift. (i) In Lime Mortar.

Excavation for foundation upto 1.5 m depth including sorting out and

28 stacking of useful materials and disposing off the excavated stuff upto 2.50 117.08 Cu.M

50 Meter lead. (A) Loose or soft soil

Providing and laying cement concrete 1:4:8 (1- Cement : 4- coarse sand

: 8- hand broken stone aggregates 40 mm nominal size) and curing

complete excluding cost of formwork in (A) Foundation and Plinth

Brick work using common burnt clay building bricks having crushing

strength not less than 35 kg./Sq.Cm. in foundation and plinth in

Cement Mortar 1:5. (1- Cement : 5 -fine sand) (B) Conventional

Providing 15mm thick cement plaster in single coat on Rough

(Similar)side of single or half brick walls for interior plastering upto

floor two level and finished even and smooth in (i) Cement mortar 1:3

(1-cement:3-sand)

Finishing Various wall Painting with weather proof exterior emulsion

paint on wall surface (two coats) to give an required shape even shade

32 after thoroughly brushing the surface to remove all dirt, and remains of 64.56 80.80 Sq.ft

loose powdered materials. etc complete.

Finishing wall with water proofing cement paint of on wall surfaces

(Two coats) to give an approved brand and manufacture and of

33 required shape even shade after thoroughly brushing the surface to 16.50 Sq.M 57.27

remove all dirt and remains of loose powered materials.

Providing & Applying Art work painting. It shall be water proof and

capable bridging, crazing and cracks, paint of makes as per approval.

Item including surface, applying one coat of primer coat shall not be

34 less then 50 micron and make listed in the tender and also including all 54.00 Sq.F 95.95

types of scafloding, safety accessories, labour, all materials lead as per

directed by engineer in charge.

Supplying & erecting approved make self-priming domestic monoblock

water pump with 0.5 H.P. motor, suitable for operation on 230 volts

c/s. AC supply with metallic flange, delivery and discharge of 32 LPM

at 10 mtrs.head.

Providing and fixing flush door with I.T.W. beading all around by using

I.T.W. frame 100 m.m. x 70m.m.. shutter fabricated from 35 mm thick

solid core non decorative flush door exterior grade bonded BWP/BWR

synthetic resin having stamped IS 12823 grade I type II including

36 priming coat & two coats of painting on surfaces and Stainless steel 17.33 Smt 3129.99

decorative type designs fixtures / fastening 2Nos. Handles, 2Nos.

Aldropes, towerbolt etc.including I.T.W. triangular batten patti of size

30m.m.x30m.m.etc. as per architectural detailed drawing and as

directed by engineer in charge..

Providing and fixing 600mm x 450mm bevelled edge mirrror of

37 superior glass mounted on 6mm thick A.C. sheet or plywood sheet and 2.00 Each 859.41

fixing to wooden pluge with C.P. brass screws and washers.

Supplying & erecting approved make low noise decorative exhaust fan

38 having square frame ABS body with inbuilt lowers & square frame. 10.00 No 1703.87

200mm with 1350RPM Cat.II

Providing window frame suitable for erection of Exhaust fan complete

39 covering the remaining portion of window with 15 mm. thick plywood 10.00 Ea 172.71

and colour washing to match the colour of the wall.

Providing and laying polished Granite Slab 18mm thick in Risers of

steps Dedo, window sill, jembs and pillars laid 10mm thick Cement

40 Mortar 1:4 (1-Cement : 4-Coarse Sand) and jointed with Grey Cement 19.00 Smt 2990.00

Slurry including full molded round front edges , rubbing and polishing

Add GST 18% Amount Rs.

Total Amount Rs.

Total Amount Rs.

Survaying,planing, Estimation, and Supervision charges @2.00 %

Total Amount Rs.

Total Amount Rs.