PROVN OF CHAIN LINK FENCING A VEHICLE PL EX 7012 AND PROVN OF TRG SHED AT GUARDS AT POKARAN MIL STN UNDER POKARAN

Amount

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm and removing surplus soil to a distance n.exc 50 m in soft / loose soil complete all as specified and directed by Engineer-in-Charge.

S&F Posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed by Engineer-in-Charge.

Supply only chain link MS galvinised fencing of any size and type complete all as specified and directed by Engineer-in-Charge. Note :- This item shall be measured and paid as per actual weight or standard weight as per SSR which ever is less.

Fixing only chain link fencing including line wire, any mesh, size and any type of standards rails straining bolt etc including provision of binding wire complete all as specified and directed by Engineer-in-Charge.

M & L for PCC (1:3:6) type C-2 using 40mm graded crushed stone aggregate as in foundation filling and mass concrete fixing of posts or struts, walls or retaining walls, any thickness size of shape including,pilasters, boundary pillars and posts (including post and bases complete all as specified and directed by Engineer-in-Charge.

Supply only MS 10mm dia round bars as line wire for chain link fencing complete all as shown on drawing complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of new steel and iron surfaces, exc 10cm width or girth and apply two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

M&L for 5 to 10mm dia mild steel screw bolts (Machine made) with hexagonal or square head at one end and screwed the other or screwed both ends each screwed and to be bolted with washers and one hexagonal or square exc 50mm long and not exc 100mm long & dia of shank 5 to 10mm including fixed with welding to angle complete all as specified and directed by Engineer-in-Charge.

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc complete, drilled for fixing of steel sheeting or other covering. Door, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings(exclusive of steel sheeting or other covering, running rails & guides) and hanging also fastening and confirming to (Fe 410 -W (Gde- E- 250) quality-A) complete all as specified and directed by Engineer-in-Charge.

M&L for squared rubble walling, Jodhpur type brought up to courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

Excavating in trenches n. exc 1.5 m wide and n. exc 1.5 m in depth for foundation etc and getting out in any type of soil complete all as specified and directed by Engineer-in-Charge.

Returning, filling in, including spreading levelling watering and well ramming in layer not exc. 25 thick complete all as specified and directed by Engineer-in-Charge.

Removel of surplus soil to a distance n exc 50m and depositing where directed at a level n exc 1.5m above from the starting point complete all as specified and directed by Engineer-in-Charge.

M&L for Keyed pointing to to squared rubble, coursed or uncoursed in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

M&L for MS work confirming to Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 as in post, strut, purlins & wind ties with (MS flat iron fillet, MS plate & angle iron) necessary cutting, drilling, welding, bolting or riveting etc including embeding in concrete complete to any type of posts screwed in position with nuts, bolts & washers, etc complete all as specified and directed by Engineer-in-Charge.

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws fixed with L & J hooks and washers, in roofs, walls etc with grade of zink coating 275 complete all as specified and directed by Engineer-in-Charge.

Surface excavation n. exc 30 cm deep and avg 15cm deepand getting out in soft/loose soil complete all as specified and directed by Engineer-in-Charge.

M & L for brocken stone boulders Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed by Engineer-in-Charge.

M&L for 75 mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even complete all as specified and directed by Engineer-in-Charge.

M&L for even spreading of 30 mm thick layer of sand cushioning including watering & consolidation complete all as specified and directed by Engineer-in-Charge.

M&L for providing cement concrete Type B1 1:2:4 (20 mm graded aggregate) in kerbs of mud stops, rounded or chamfered on edges etc complete all as specified and directed by Engineer-in-Charge.

M&L for 80 mm thick machine pressed precast concrete interlocking paver block with grey cement and pigments any shape and size conforming to IS 15658-2006 of M-35 grade complete all as specified and directed by Engineer-in-Charge.

M/s Rashid Mohammed (BID ID -3163560)

Habib Traders (BID ID -3162612)

Rakesh Choudhary Contractor (BID ID -3157506)