AS AND AS TO WINDOWS AND DOORS IN HANGAR 1, 6, 19 AND 20 IN TP AREA AND CONSULTANCY SERVICES FOR SECTION BUILDINGS UNDER LBW, AS AND AS TO PERIMETER WALL FROM TOWER 12 TO TOWER 13 UNDER LBW AT NAVAL STATION BHEEMUNIPATNAM UNDER GE (P) NAVY KALINGA BH

Amount

Taking down PVC Chowkhats or frames exc. 1.5 sq. m but n exc 4.0 Sqm each with shutters (without taking off shutters from the frames)

Taking down Chowkhats or frames exc. 1.5 sq. m but n exc 4.0 Sqm each with shutters (without taking off shutters from the frames)

Taking down shutters of any description exc 1 Sqm & n.exc.2 Sqm each.

Taking down cement plastering on brick or concrete wall ,including raking out joints,hacking for key,scrubbing down with water etc

S & F Solid PVC Door Frame of size 100mm x 60mm made out of 5mm WOOD GRAIN printed PVC sheet used instead of plain colour PVC sheet ans edges will be painted to match with printed sheet, reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded wood grain printed PVC sheet & 5mm thick x 15mm wide PVC sheed beading used insied Stiles and Rails and decorative PVC beading of 10mm x 10mm (90*) used instead of exposed portion of PVC sheet beading and the paneeling of wood grain printed PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing

S&F UPVC window,(unplastisized poly-Vinyl Chloride) sliding windows multi-chambered and stiffened framed windows using 88mm x 52mm size sections all-round as main frames and shutters made with profile sections of size 57mm x 42mm, including the cost and fixing of 5mm thick clear float glass in shutters and stainless steel wire mesh shutters shall have well defined welded corner joints without any gaps, fixed the window unit to the existing masonry with anchor fasteners as required. The shutters shall have necessary handles and other associated fittings to facilitate smooth operation. Both the frames and the shutters shall be reinforced with GI profiles of thickness 1.25mm the entire window is covered with MS powder coated tube of size 40mm x 20mm all-round the frame the frame section, 10mm square bars horizontally placed at 120mm C/C and suitably placed vertically to avoid buckling and providing structural strength, Minimum weight shall be 10kg/Sqm and fixed to UPVC frames with suitable fasteners. The gaps between the window frames and masonry walls shall be filled with silicon or with any other suitable filler materials complete all as specified and directed. Make : Rajshri Plastiwood/Veka/Sintex/Duroplast Extrusion Pvt. Ltd

S&F Steel (white powder coated) crescent lock for UPVC sliding window/door with necessary screws etc complete all as specified and as directed.

M&L Second class hard wood Plain solid straight chowkhats and frames,wrought ,framed, rebated on the solid,rounded or chamfered ,put together with glue pinned at joints,supplied and fixed.

S&F Flush shutters 30 mm thick, solid core construction, with block board core and ply wood face panels, commercial type on both sides complete.

M & L for 35mm thick IInd class HW Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (with sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a);

S&F factory made shutters 35mm thick Plain, framed, panelled shutters of 2nd class hard wood (two panel), with lock rail and panels of 9mm BWP commercial ply or 12mm veneered perticle board with commercial veneering on both faces, the size of rail and style as per IS : 1003 (part-I), kiln seasoned chemically pressure treated.

S&F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165

M&L Preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, and treated with tar or coal tar black paint treating ends of posts, backs of chowkats, etc, area tarred exc 0.1 sq.m but n exc 0.5 sq.m each ditto

M&L Preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, and treated with tar or coal tar black paint treating small articles such as stop, covers, gully gratings, holdfasts, ends of posts, backs of chowkats, etc, area n exc 0.1 Sq.m each, ditto

S & F 125 mm Butt hinges, Medium weight, cold rolled mild steel, and fixed

S & F of 200mm Aluminium anodised,barrel tower bolts of extruded section and fixed

S & F of 150 mm Aluminium anodised,barrel tower bolts of extruded section and fixed

S & F Aluminium handles, cast type,anodised of size 150 mm

S & F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S & F Floor door stopper 150 mm of Aluminium alloy body and tongue,anodised, with hard drawn steel spring,fixed in floor complete.

M&L for 10 mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and fair rendering is to be finished even and smooth (without using extra lime or cement) complete all as specified and directed

M&L Preparation of new plastered wall surfaces and applying two coats of plastic emulsion paint over priming paint including applying 3mm thick wall care putty .

S&F 12mm thick toughened glass with stainless steel (Grade 304L) studs and bolts on all edges as per site requirements with standard make all as specified and as directed

S&F Stainless steel handrails, fabricated to required design, using 304L stainless steel pipe of 50mm dia welded to 25mm dia stainless steel pipe balusters @ 300mm centre to centre and fittings, including welding and polishing and fixed with necessary stainless steel plates, flanges, canopies, screws etc, complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

M&L glazed ceramic coloured tiles 300 x 450x 6-7 mm thick as in verticle surface set & jointed in neat cement slurry & pointed with coloured cement to match over 10 mm thick rendering with CM 1:4 all as specified &directed.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar or cement lime lime mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified .

Demolition of cement conreteConcrete of any description and in any position not otherwise specifically provided for complete all as specified.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/loose soil complete all as specified and as directed

M & L for Cement concrete type D2 of 1:4:8 of (40 mm aggregate) in foundations, filling and mass concrete

M&L for Reinforced Cement Concrete M-30 design mix (Using 20mm graded granite stone aggregate) in footings, plinth beams and the like complete all as specified and directed.

M&L for Reinforced Cement Concrete M-30 design mix (Using 20mm graded granite stone aggregate) in columns and pillars complete all as specified and directed.

M&L for Reinforced Cement Concrete M-30 design mix (Using 20mm graded granite stone aggregate) in bands, top bands, lintel beams and the like complete all as specified and directed.

Use and waste of form work to sides of foundation/ footings, plinth beams and similar work for rough finished surfaces complete all as specified and directed.

Use and waste of form work to sides of columns and pillars for for fair finished surfaces complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.

M & L Mild steel TMTbars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed

M & L Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft / loose soil.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point

M & L for Brickwork with Fly ash bricks, straight or curved on plan exc 6m mean radius with built in CM 1:6

S&F mild steel work in hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed by the Engineer-in-Charge.

M & L for Rendering 15mm thick with CM 1:4 on fair faces of brickwork or concrete surfaces finished even and fair without using extra cement complete all as directed

S&F 610mm dia. concertina coil, galvanised, precoated with black anti-corrosive paint, weighing approx. 8 Kg per coil of 6-8m strech and fixing to any type of standard rails, straining bolts etc. including securing or tying at crossings with necessary clips/pins etc. complete all as specified and as directed by the Engineer-in-Charge.

S&F galvanised. 2 strand, steel barbed wire 2.24mm dia. barbed with 2mm dia. barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. complete all as specified and as directed by the Engineer-in-Charge. Note: Each line wire will be measured.

M & L for preparation of new steel Surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of synthetic enamel paint over a coat of redoxide primer

M&L for preparation of new plastered surfaces and applying two coats of exterior emulsion paint over acoat of primer on walls complete all as specified and as directed by the Engineer-in-Charge.

M/s SRINIVASA REDDY CONSTRUCTIONS

SSV CONSTRUCTIONS

SAI SAMPATH ELECTRICAL AND ENGINEERING