GE CHD T 75 2025 26

Taking down Cement plaster or cement lime plaster on brick or stone walls including raking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

18/19 mm thick Plywood (solid ) type BB fixed with screws to timber framework including PVC self adhesive as per manufacturers instructions complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (reinforced) (reinforcement cut as required to facilitate demolition) as in roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas and similar suspended work complete including disposal of unservicable rubbish outside Cantt area all as specified and directed by Engineer-in-Charge.

Demolition of brick work or stone/boulder masonary built in cement mortar incl all quions arches, pillar or any other descrption etc complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames exc 1.5 sqm but n.exc 4 sqm each (without taking off shutter from the frame) including cutting holes through brickwall and making good the dismantled portion in cm 1:3 or PCC 1:2:4 and removing from the site including dismantling brick work of hold fasts etc complete all as specified and directed by Engineer-in-Charge.

PVC strip type wall panelling 5 mm thick coloured wood grain printed design approved by engr-in-charge, inclusive of PVC frame and overlap strips and corner angles ,fixing on to wall incl moulding end caps fixed with PVC sleeves and screws as required at site including dismantling of wall panelling complete all as specified and directed

Taking down steel tubing and connections of 15 mm bore in pipe with all fittings from walls,ceilings and floors and removal from site complete all as specified and directed by Engineer-in-Charge.

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall/ridge, fixed with self tapping screws,hooks etc complete all as specified and as directed by Engr-in-charge.Colour to be decided by GE

Dismantling existing Brick tiles or terracing tiles, single layer on roofs including disposal of unservicable rubbish outside Cantt area complete all as specified and directed by Engineer in Charge.

Preparation of new or previously untreated steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

Use & waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) etc. (rough finished flat surfaces of concrete) complete all as specified and directed by Engineer-in-Charge.

Cutting grooves or rebates in parapet walls 75 mm wide and 65 mm deep and making good in cement mortar 1:3 after inserting APP membrane and shaping horizontal face of groove complete all as specified and directed by Engineer-in-Charge.

Rendering 10 mm thick in cement mortar 1:4 on fair faces of brickwork or concrete surfaces finished even and fair without using extra cement mixed with water proofing compound as per manufacturers instructions complete all as specified and directed by Engineer-in-Charge.

Plain cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in cement concrete in roof padding, roof kerbs or mud stops,back filling of chowkats, holdfasts,coping,bed plates,cills,benching rounded or chamfered on edges with and including using necessary use and waste of formwork for fair finished surface complete all as specified and directed by Engineer-in-Charge.

Repairing the edges of concrete chajjas,facias,columns not exc 450 mm wide by providing PCC (1:2:4) type B-0 thickness 10 to 20 mm as required including

Use & waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping (rough finished flat surfaces of concrete) omplete all as specified and directed by Engineer-in-Charge.

Vitrified ceramic tiles double charged dark shade 10 mm thick (Square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm,as in skirting etc set and jointed with 4 mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desired shade,hardener ,resin in the ratio of 8:1:2 laid over and including 10mm thick rendring in CM (1:4) complete all as specified and directed by Engineer-in-Charge.

Cement concrete 1:4:8 type D 2 (40 mm graded mechanically crushed stone aggregate) as in foundation,subbase,path finishing concrete surface even and fair complete all as specified and directed.

First quality Non - skid coloured Ceramic tiles 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors etc. set and jointed with 4 mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desired shade,hardener ,resin in the ratio of 8:1:2 laid over and inculding 15 mm thick screed in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

Demolition of lime/Cement concrete unreinforced as in Ground Floor and paving exc. 15cm thick (above or below G.L.) complete including china mozaic,WC ,disposal of unservicable rubbish outside Cantt area all as specified and directed by Engineer-in-Charge.

Floor machine heavy duty ISI marked for aluminium door with all accessories etc complete all as specified and directed by Engineer-in

-Charge.

Toughened glass 12 mm thick including fixing with cleat in floor,ceiling and lining alongwith hinges to hold door arrangements including hacking out old glass complete all as specified and directed by Engineer-in-Charge.

Water proofing treatment to roof and sunken portion using APP polymeric water proofing membrane minimum 3 mm thick and weighting not less than 3.6 Kg/Sqm black finish reinforced with non-woven polyster matt wt not less than 150 gms/Sqm with thermo fusable finish laid over compatible bitumen primer at the rate of 0.40 Ltr/Sqm over cleaned surface including parapet,applying a coat of blown bitumen 85/25 grade @ 1.2 kg per square metre over priming coat torching over laps with a propane or butan gas torch with a over lap of 100 mm at the side and 150 mm at the ends and sealing all as per manufacturers instructions incl two coats of aluminium paint over APP membrane,wire brushing and cleaning the top surfaces of concrete, roof surfaces etc. with water including flashings and junction of parapets etc complete all as specified and directed.

Note: For the purpose of arriving at Net contract sum amount, the amount of credit schedule i.e Sch 'A' section II (i.e Rs 82,315.00 shall be deducted from the total amount arrived.

Brick work with sub class 'B' bricks, class designation 100, old size bricks, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in built in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames n.exc 1.5 sqm each (without taking off shutter from the frame) including cutting holes through brickwall and making good the dismantled portion in cm 1:3 or PCC 1:2:4 and removing from the site including dismantling brick work of hold fasts etc complete all as specified and directed by Engineer-in-Charge.

Rendering 15 mm thick in cement mortar 1:6 on other than fair faces of brickwork or concrete surfaces finished even and fair without using extra cement, complete all as specified and directed by Engineer-in-Charge.

Cleaning the RCC surface including flashings and junction of parapets etc with wire brushes and water and applying a coat of cement slurry @ 3 Kg/sqm of surface complete all as specified and directed by Engineer-in-Charge.

Rendering 10 mm thick in cement mortar 1:3 as in ceiling/soffits of slabs/Chajja/ Sunshade finishing the plastered surface even & smooth without using extra cement etc complete all as specified and directed by Engineer-in-Charge.

Preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over and including a coat of alkali resistant primer and 1 mm wall care putty including preparation of surface complete all as specified and directed.

Preparation of new plastered surfaces of wall and applying Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) including preparation of surface complete all as specified and directed.

Preparation of plastered or unplastered new surfaces of ceilings and applying three coats of white wash including preparation of surface complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs aluminium ( Die cast ) Door closer hydraulically regulated, designation No. 1 universal type, suitable for door shutters up to 700 mm in width and of weight not more than 35 kg complete all as specified and directed by Engineer-in-Charge.

Preparation of old or previously treated steel and iron surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed by Engineer-in-Charge.

Complete removal of existing treatment,preparation of surfaces of walls brooming down, applying one coat of white cement based wall care putty after applying emery paper or sand paper and applying two coats of oil bound distemper on walls over and including a coat of alkali resistant primer complete all as specified and directed by Engineer-in-Charge.

Complete removal of existing treatment,preparation of surfaces of walls, brooming down and applying three coats of white wash on walls complete all as specified and directed by Engineer-in-Charge.

Complete removal of existing treatment,preparation of surfaces of ceiling, brooming down and applying two coats of white wash on walls complete all as specified and directed by Engineer-in-Charge.

Plain cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregate as in surface channels with and including using necessary use and waste of formwork for fair finished surface complete all as specified and directed by Engineer-in-Charge.

Floor door stopper of aluminium alloy body and tongue, anodised,with hard drawn steel spring,fixed in floor with overall length of cover plate 140 mm complete all as specified and directed by Engineer-in-Charge.

Preparation of old Plastered of walls etc by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying one coat of oil bound distemper complete all as specified and directed by Engineer-in-Charge.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws,hooks etc complete all as specified and as directed by Engr-in-charge.Colour to be decided by GE

Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 conforming to Fe 410-W (Gde E- 250) quality A and fixing complete all as as specified and directed by Engineer-in-Charge.

Taking down shutters of any description exc 1.0 sqm but n.exc 2.0 sqm each and removing from the site etc complete all as specified and directed by Engineer-in-Charge.

Factory made Pressed steel frames, confirming to IS, having profile 125 x 60 mm , 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, and fixing only 100 mm size hinges, lock strike plate, etc., with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge.

35 mm thick factory made Flush shutters, solid core construction, with particle core and plywood face panels, commercial type on both sides face covered with decorative face veneer with lipping/frame to match with 1 mm thick mica supplied and fixed complete all as specified and directed by Engineer-in-Charge.

35 mm thick factory made glazed & Skeleton shutters of 2nd class Hardwood open rebated & prepared to receive glass or gauze etc without sash bar open rebated with edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass or guage etc size ofstiles rails etc as specified in sec 8 clause 8.24 (a) of SSR Part-I (2009) complete all as specified and directed by Engineer-in-Charge.

Factory made box type steel windows with pressed steel frame min 1.25 thick complete including mild steel acessories like lugs, door stopper, holdfasts, pintol hinges, handles( minimum One for each shutter), and ISI marked tower bolt 150mm size (minimum 2 for each shutter) etc. with glazing bars and without glazing bars (Double shutter ) dovetailed or welded with one shop coat of zinc chromate primer, complete all as shown on drawing No. TD-276(R), Sheet No 1/4 to 2/4, 3/4, 4R/4 and as specified and directed by Engineer-in-Charge. Note: (i) Fabrication as per TD-276 (R) SH 1/4 to 2/4, 3/4, 4 (R) /4 (ii)Mode of measurement Unit will be for the complete window except Glass/ Gauge but incl fittings, ISI marked iron mongery complete as per TD. (iii) The PCC back filling in chowkhat of window, Grills,Sheet glass and wire gauge will be measured and paid separately against respective items.

Factory made box type steel windows with pressed steel frame min 1.25 thick complete including mild steel acessories like lugs, holdfasts.( Fixed type ) dovetailed or welded with one shop coat of zinc chromate primer, complete all as shown on drawing No. TD-276(R), Sheet No 1/4 to 2/4, 3/4, 4R/4 and as specified and directed by Engineer-in-Charge. Note: (i) Fabrication as per TD-276 (R) SH 1/4 to 2/4, 3/4, 4 (R) /4 (ii)Mode of measurement Unit will be for the complete window except Glass/ Gauge but incl fittings, ISI marked iron mongery complete as per TD. (iii) The PCC back filling in chowkhat of window, Grills,Sheet glass and wire gauge will be measured and paid separately against respective items.

Dismanting of wrought iron or mild steel of any description not otherwise provided for in any location and any position complete all as specified and directed by Engineer-in-Charge.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples fixed in repairs complete all as specified and directed by Engineer-in-Charge.

25mm dia stainless steel fancy type drapery rod of wall thickness 0.9 mm with fixed brackets,stops and rollers including taking out of old pelmet/bracket, complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs 15 mm fancy type chromium plated two way bib tap with flange screwed down high pressure CP cast copper alloy with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union complete all as specified and directed by Engineer-in-Charge.

Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification complete all as specified and directed by Engineer-in-Charge.

Aluminium anodised,barrel tower bolts of extruded section with length of bolt 150 mm and dia of bolt not less than 10 mm,ISI marked complete all as specified and directed by Engineer-in-Charge

18/19 mm thick HDHMR board (1st quality ) both side with decorative choice lamination fixed with screws in cupboard shutters/shelves and kitchen cabinets complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of stainless steel butt hinges 100 mm long medium weight cold rolled fixed with stainless steel screws orwelding to existing MS frames complete ,all as specified and as directed by Engr-in-charge.

300 mm long,Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed bolt not less than 16mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified & directed by Engineer in Charge.

Supplying and fixing in repairs 15 mm fancy type chromium plated three way mixer tap fancy type with flange screwed down high pressure CP cast copper alloy for mixing hot and cold water suitable for 15mm bore pipe or union complete all as specified and directed by Engineer-in-Charge.

Sheet glass 5.5 mm thick, ordinary quality and glazing with silicon sealant & spring glazing clips using Silicon for fixing of glass in addition to glazing putty, in squares not exceeding 0.5 Sq. mtr in each pane, complete all as specified and directed by Engineer-in-Charge.

150 mm long extruded aluminium alloy handles, fabricated type,anodised complete all as sp

ecified and directed by Engineer-in-Charge.

Magnetic catchers cum silencer 50mm long superior quality ,fixed with stainless steel screws to PVC/Wooden moulded shutters frame work in kitchen cabinets,cupboards etc complete all as specified and directed by Engineer-in-Charge.

20 mm thick grey coloured Cement concrete tiles 25cm x 25cm , machine pressed; set jointed,grouted and pointed flush in cement mortar (1:4) mixed with 5% of crude oil by weight in floors/roof and cut and polished with grey cement and no pigment over and including 20 mm thick screed bed in cement mortar (1:4) mixed with and including water proofing compound (Pidilite LW @ 200 ml per 50 Kg of cement ) complete as specified and directed by the Engineer-in-Charge

Supply and fixing in PVC prelaminated Gypsum Ceiling board 8 mm thick with and including anodised aluminium snap grid framework for ceiling having grid size 605 x 605 mm comprising of wall angle of size 25 mm x 25 mm x1.3 mm,main runner of size 38 mm x 25 mm x1.3 mm. The grid system shall be suspended at every 1200 mm c/c in both directions by using 3.5 mm dia aqualine wire fixed to purlin or RCC roof with suitable fasteners to withstand the load of grid system with ceiling board complete all as specified and as directed by Engr-in-charge.Colour to be decided by GE

0.9 mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed by Engineer-in-Charge.

Preparation of old Plastered of walls etc by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying one coat of cement based paint complete all as specified and directed by Engineer-in-Charge.

Factory made single extruded WPC (Wood Polymer Composite) solid plain board of size 25 mm thick comprising of virgin polymer of K value 58-60 Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter including PVC beading on exposed surface complete all as specified and directed by Engineer-in-Charge.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge

Soap dish chromium plated fixed in position with plugs and chromium plated brass screws and wooden/plastic screws complete in all respect all as specified and directed by Engineer-in-Charge'.

Supply and fixed in repair brass chromium plated, tubular towel rail, 20mm dia, 60cm long between flanges complete all as specified and directed by Engineer-in-Charge.

Supply and fixed in repair flushing kit internal for single piece EWC complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 brass UNION fittings, ISI marked for CPVC pipe outer diameter 20 mm bore complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 Tank Adaptor nipple fittings, ISI marked for CPVC pipe outer diameter 20 mm bore complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in existing position Vitreous China Wash down water closet (Pedestal pattern), white including plastic seat cover white,P or S trap, and 10 ltr capacity PVC valveless syphonic action type flushing cistern low level white with inlet ball valve float and handle with brackets,connection to outgoing pipe and flushing pipe etc complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs Gun-metal ball valve (quarter turn type ) with MS lever handle suitablr for GI pipe of 15 mm bore complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs vitreous china wash hand basin with pedestal white flat back of size 550x440mm including CI brackets , chromium plated waste coupling, waste pipe etc., (incl all waste fittings) complete all as specified and directed by Engineer-in-Charge.

Vitreous China EWC one piece water closet pan type of size 365 mm x 655mm x700 mm white with and including seat cover,flush cistern 10 ltr capacity,connection pipe,P or S trap (closed pattern incl all necessary accessories like rag bolts,kit/gel gaskets,CP jet with connector pipe ,fixing bolts complete all as specified and directed by Engineer-in-Charge.

10 ltr capacity PVC valveless, syphonic action dual flush type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, 32 mm dia flush pipe complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs fancy type stop valves/Angle valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, all as specified, of 15mm bore, fancy type, chromium plated with long shank and cup complete all as specified and directed by Engineer-in-Charge.

Disconnecting existing tanks of capacity exc. 250 ltr & n. exc. 500 ltr, setting aside and removing from site complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs 15 mm fancy type chromium plated fancy type bib tap brass long body with flange screwed down high pressure CP cast copper alloy with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union complete all as specified and directed by Engineer-in-Charge.

Cutting grooves or rebates in brick walls 75 mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed by Engineer-in-Charge.

for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs 15 mm fancy type chromium plated fancy type Pillar taps, cast copper alloy, with capstan heads,chromium plated,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

Supply and fixed in repair spray jet brass chromium plated including suitable length of PVC connection pipe complete all as specified and directed by Engineer-in-Charge.

PVC connections 15mm size with PTMT nuts of length 600 mm fixed in repair complete all as specified and directed by Engineer-in-Charge.

Cast iron 'P' or 'S' trap ISI marked suitable for 100 mm bore including jointing fixed in repair complete all as specified and directed by Engineer in Charge.

Disconnecting existing tanks of capacity exc. 500 ltr & n. exc. 1000 ltr, setting aside and removing from site complete all as specified and directed by Engineer-in-Charge.

Factory made single extruded WPC (Wood Polymer Composite) solid single side PVC laminate with PVC foil of minimum 14 microns thick of approved colour/shade board of size 25 mm thick comprising of virgin polymer of K value 58-60 Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter including PVC beading on exposed surface complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs Gun-metal ball valve (quarter turn type ) with MS lever handle suitablr for GI pipe of 20 mm bore complete all as specified and directed by Engineer-in-Charge.

Corner glass shelf 5 mm thick 23 mm wide fixed with suitable mild steel chromium plated brackets,nuts & bolts fixed in position complete in all respect all as specified and directed by Engineer-in-Charge'.

Health faucet (ABS Body) hand shower mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect all as specified and directed by Engineer-in-Charge'.

Supply and fixing in repair sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete ,all as specified and directed by Engineer-in-Charge.

Supply and fixed in repair Brass chromum plated overhead shower rose of size 150 x 150 mm (square ) with Brass chromum plated shower arm 450 mm long with flange with swivel joints, fancy type screwed down for 15mm dia iron pipe complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs table top vitreous china wash hand basin of size 600 mm x 450 mm x150 mm including CI brackets , chromium plated waste coupling, waste pipe etc., (incl all waste fittings) complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete ,all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs 15 mm fancy type chromium plated two way fancy type Pillar cock single lever of 450 mm , cast copper alloy, with capstan heads,chromium plated,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed

PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75 mm bore fixed in repair including jointing to waste pipe in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engineer in Charge.

Supply and fixed in repair toilet paper holder brass chromium plated fixed with brass screws complete all as specified and directed by Engineer-in-Charge.

Sheet glass 4 mm thick, ordinary quality and glazing with silicon sealant & spring glazing clips using Silicon for fixing of glass in addition to glazing putty, in squares not exceeding 0.5 Sq. mtr in each pane, complete all as specified and directed by Engineer-in-Charge.

Disconnecting existing tanks of capacity exc 500 ltr but not exc 1000 ltr , setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. measured separately) complete all as specified and directed by Engineer-in-Charge.

Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc of capacity exc 250 ltr but not exc 500 ltr complete all as specified and directed by Engineer-in-Charge.

Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc of ca

pacity exc 500 ltr but not exc 1000 ltr complete all as specified and directed by Engineer-in-Charge.

75mm bore, PVC (SWR) pipes with pressure rating not less than 4 Kg/sqcm,single socketed, in any length with rubber ring joints, fixed to walls with and including MS clamps made out of flat iron of size 25 mm x 3 mm including nuts,bolts or laid in trenches complete all as specified and directed by Engineer-in-Charge.

110 mm bore, PVC (SWR) pipes with pressure rating not less than 4 Kg/sqcm single socketed, in any length with rubber ring joints, fixed to walls with and including MS clamps made out of flat iron of size 25 mm x 3 mm including nuts,bolts or laid in trenches complete all as specified and directed by Engineer-in-Charge.

Chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union suitable for 15 mm dia pipe with Brass chromium plated shower rose 125mm size fixed in repair including making connections and fixed in position complete in all respect all as specified and directed by Engineer-in-Charge'.

PVC(SWR) bends (any radius), for 75 mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge.

PVC(SWR) bends (any radius), for 110mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge.

Chrome plated food grade stainless steel cutlery wire ,pan basket of a modular kitchen (storage basket,cup/saucer basket,gas basket,thali basket,cutlery basket,grain trolley,plain basket,bottle pullout tray 0 min loading capacity 65 kg made of min 6 mm stainless steel round bars properly welded and joints finished by grinding any description/pattern as approved by GE ,fixed with sliding channel,revolving wheels fixed with screws to timber frame work in kitchen cabinets,cupboards etc complete all as specified and directed by Engineer-in-Charge. Note : 1. Weight of fittings/fixures like handles,hinges,ball bearing runners,telescopic channels will not be measured 2. Only weight of SS wire baskets will be measured before fixing 3. Fixing of all fittings/fixures like handles,hinges,ball bearing runners,telescopic channels are included in this item,supply will be paid separately

Total of Schedule 'A' Rs.