C/O Govt High school Building at Koon in Tehsil Dharampur Distt Mandi (HP)

Amount

Excavation in hilly areas in all heights and depths and in all kinds of soil by manual/mechanical means including saturated soil comprising of ordinary soil, soft rocks, hard rocks, chiseling/wedging out of rock (where blasting is prohibited) and other intermediate classification of soil, setting out true to the required lines, grades width cutting and trimming of side slopes and level as shown in the drawing and as directed by the Engineer-in-Charge at site according to the MORD technical specification clause 1603.1, 1603.2 and sorting out useful materials and stacking the same in all leads and lifts in acquired width of the road and transportation of un-useful material for filling in road ways, camber, embankments for grade improvements and disposal of all surplus un-useful material to acquired width of the road or on approved dumping sites through all modes of transportation including head load or animals transport or mechanical means alongwith its leveling fine dressing and carriage of machineries, materials, tools equipments and safety measures and other incidentals necessary to complete the work by mechanical means and/or labour if required. Any loss to the public/private property during the course of execution shall be the absolute responsibility of the contractor which shall have to be duly compensated by him in all cases as per direction of the Engineer-in-Charge A recovery of useful stone for 84.62cum (Eighty four decimal six two zero ) cubic metre @ Rs. 300/- (Rupees three hundred only) per cubic metre shall be effected on pro-rata basis in each running bill from this item. The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Excavation in foundation, trenches etcetera in all classification of soil such as pick work, jumper work, blasting work soft rock and hard rock including chiselling wedging and any other mixed variety in dry or saturated conditions upto any depth and lift including pumping and bailing out water where required including stacking the serviceable and unserviceable materials separately as directed and then returning the stacked soil in fifteen centimeters layers when required into plinth and sides of foundation etcetera consolidating each deposited layer by ramming and watering and then disposing of all surplus un-serviceable excavated earth within all leads and lifts as per directed by the Engineer-in-Charge including entire carriage of material with in all leads and lifts, disposed materials to be neatly dressed and levelled including other incidentals. The rates are inclusive of royality, GST or other taxes imposed by the Government.

Earth work in excavation for all type of structures such as retaining walls, Breasts walls,culvrts, drains, Parapets, Etcetra in all type of classification of soil comprising of ordinary soil, ordinary rock, hard rocks, chiseling/wedging out of rocks (where blasting is prohibited) as per drawings and technical specification clause 305.1 and as per direction of the Engineer-in-Charge including setting out, construction of shoring and bracing, removal of stumps and other deleterious materials and disposal of materials upto all leads and lift including dressing of sides and bottom and back filling in trenches with excavated suitable approved material to the original surface in layers not exceeding 150mm (One hundred fifty millimetre) compacted thickness including shoring and strutting and pumping and bailing out water (surface and sub soil water) upto any depth and any quantum of water including cleaning of slush which may arise out during dewatering as per the direction of the Engineer-in-Charge and including entire carriage of material within all leads and lifts and other incidentals The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Filling in plinth with sand under floors including watering ramming consolidating and dressing complete including carriage of material with in all leads and lifts and other incidentials charges.

Providing form work with mild steel plates 3.15 mm (three point one five millimetre) thick welded with angle iron in frame of 30x30x5mm (Thirty into thirty into five millimetre) size so as to give a fair finish including centring, shuttering, strutting and propping and centring etectera with wooden battens and ballies in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced and plain concrete work upto all floor level in all heights including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals.

In foundation,footings bases of columns and mass concrete including plinth beam and column upto all floors

In flat surfaces such as soffits of suspended floors,roofs,landing and the like floor upto any thickness

In columns, pillars posts and struts square rectangular or polygonal in plan.

In beams, cantilevers, girders and lintels, sides and soffits of beams, beams haunching below supporting cantilevers girders breasumers and lintels upto any depth /height

In edges of slabs and breaks in floors and walls in any width.

Stair Case with sloping or stepped soffits excluding landing beams, cantilivers, girders and lintels.

Providing and laying mechanically mixed and vibrated cement concrete 1:3:6 (One cement: three sand: six graded/crushed stone aggregate 40mm (Forty millimetre) nominal size) as per drawing and specification including curing complete but excluding cost of from work in foundation and plinth including all heights/depths including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and Laying concrete for plain/reinforced concrete mechanically mixed and vibrated in open foundation retaining walls, breast walls and like substructures etcetra complete as per drawings nominal mix 1:5:10 (One cement : five sand : Ten graded crushed stone aggregate) 40mm (Forty millimetre) nominal size including cost of form work and curing complete without plum as per HPPWD specification complete in all respect including entire carriage of materials within all leads and lifts and other incidentals. The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated cement concrete 1:4:8 (One cement: four sand: eight graded/crushed stone aggregate 40mm (Forty millimetre) nominal size) as per drawing and specification including curing complete but excluding cost of from work in foundation and plinth including all heights/depths including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete in mouldings as in cornices, windows sills etc, including setting in cement mortar 1:3 (1 cement : 3 coarse sand) cost of required centering, shuttering but, excluding the cost of reinforcement, with design mix M-20 (twenty) including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying in position machine batched and machine mixed and vibrated design mix M-20 (twenty ) grade cement concrete for reinforced cement concrete work,to obtained minium crushing strength of 25N/mm2 (Twenty five ) Netwon per millimetres square) with minium cement contents of 350Kg/Cum (Four hundred twenty five killogramme per Cubic metres) using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge in all heights/ depth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of royality, GST or other taxes imposed by the Government.

All works upto plinth level.

All works above plinth level upto all floor level.

Providing and laying tor steel made of TATA/ SAIL reinforcement for reinforcement cement concrete work including bending, binding straightning and placing in position complete upto all floor level in all heights including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and laying damp proof course 40mm (Forty milimetres ) thick with cement concrete 1:2:4 ( One cement : two sand : four graded crushed stone agregate 12.5mm ( Twelve decimal five milimetres ) nominal size curing complete including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of royality, GST or other taxes imposed by the Government.

Applying a coat of residual petroleum bitumen of grade of VG-10 (ten) of approved quality using 1.7kg (One point seven) Kilogramme per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of royality, GST or other taxes imposed by the Government.

Back filling behind abutment , wing walls and return walls complete as per drawings and technical specification Clause 1204.3.8. with Granular Material and as per direction of Engineer-in-Charge including entire carriage of materials within all leads and lifts and other incidentals. The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Stone soling under floors dry hand packed upto all floor level including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing weep holes in brick masonry / Stone masonry / plain/reinforced concrete in retaining walls, breast walls and the like with 110mm ( One hundred ten ) dia PVC pipe Finolex/ Supreme having pressure not less than 4.00 Kg/Cm² ( four kilogramm ) per centimetre square extending through the full width of the structure with slope of 1(V):20(H) ( one vertical : twenty horizontal ) towards drawing face complete as per drawing and technical specification clause 614,709,1204.3.7 in all leads and lifts and carriage of material by all modes of transportation as per the direction of Engineer- in-chrage. The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Brick work (second class) using common burent clay building bricks in with cement mortar 1:6 (one cement : six coarse sand) curing complete upto plinth levels in all heights/ depth including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Brick work (second class) using common burent clay building bricks in Super structure above plinth level with cement mortar 1:6 (one cement : six coarse sand) curing complete upto all floor levels in all heights/ depth including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 300x16mm (three hundred into sixteen millimetres) anodized aluminium sliding door bolts anodized / powder coated colour or shade with bolts and nuts screws etcetera complete including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals:The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

Providing and fixing 200x10mm (Two hundred into ten millimetres) aluminium tower bolts (barrel type) anodized/ powder coated transparent or dyed to required shade and colour with screws including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

250 x10 mm (Two hundred fifty into ten ) millimetres

150 x10 mm (Two hundred fifty into ten ) millimetres

Providing and fixing aluminium handles anodized/ powder coated transparent including entire carriage of materials with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals. The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government.

125mm (one hundred twenty five millimetres)

100mm (one hundred millimetres)

Providing and fixing AISI-Grade stainless steel floor door stopper ISI marked (anodic coating not less than grade AC10 (ten) as per IS:1868) transparent and dyed to required colour and shade with necessary screws etc. complete upto all floor level including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of royality, GST or other taxes imposed by the Government.

Providing and fixing 100 mm (hundred millimetre) stainless steel hard drawn hooks and eye complete with all floor level including entire carriage of materials upto all leads and lifts. The rates are inclusive of royality, GST or other taxes imposed by the Government.

Providing and fixing(SINGLE REBATE DOOR FRAME) door frame fabricated from sections roll formed out of 1.2 mm (one point two millimetre) thick galvanized steel (Base steel as per IS 513) with zinc of 120 gms/sqm (one hundred twenty gram per square metre). The overall size of section should be 80x50 mm (eighty into fifty millimetre) and 105x60 mm (one hundred five into sixty millimetre) with rebate of 37 mm (thirty seven millimetre) for shutter. The frame section should be cut to length and metre joint with corner bracket made of CRCA electroplated. The frame should be provided with 3 (three) number of M.S. powder coated 4" (four inch) butt hinges of 2 mm( two) millimetres thickness welded to frame and 6 (six) number of 1.2 mm( one point two) thick CRCA electroplated stiffeners should be welded to frame and 6 (six) number 8" (eight inch) MS holdfasts with spilt end tail welded to stiffeners plates and 1(One) number aldrop receiver. Each frame should be provided with 25x50 mm(twenty into fifty) millimtres tie rod at bottom. All welded places should be treated with protective coat of zinc rich primer. The entire frame should be provided with a coat each primer completeincluding entire carriage of material with in all leads and lifts and as per drawings and technical specifications as per direction of Engineer-in-Charge including other incidentals .The rates are inclusive of royality, GST or other taxes imposed by the Government.

Providing and fixing ECO-5000 ( Five thousand) Series Windows fabricated from roll formed sections made of Galvanized steel colour coated / powder coated (Base steel as per 513"D" quality Galvanized as per IS 277 with Zinc of 120 gram/sqm (One hundred twenty gramme per square metres with total coated thickness of 0.60mm (zero point six zero Coated section should be with primer coat of epoxy primr of 5-7 (five -seven) micron thick finish apinted with polyster paint of 12-16 microns thick and black coated with alkyd backer of 5-7 (five -seven) microns, or powder coated with pure polyster powder up to 50-60 (fifty -sixty) micron thick. Section for frame should be of 98x50mm,(ninety eight into fifty) section for mullion should be of 46mmx70mm 0.58mm (forty six into seventy into zero point five eight)thickness, section for shutter frame should be of 46mmx46mmx0.58mm,( forty into forty six into zero five eight) millimetres section for fixed glass beed should be of 18mmx25mmx0.58mm (Eighteen into twenty five into zero point five eight)millimetres into twenty and section for fly mesh shutter frame should be 20mm x 40mmx0.58mm. (Twenty into forty into zero point five eight) millimetres frames and mesh shutter section 18mmx6mmx0.58mm (Eighteen into six into zero point five eight)millimetres should be cut to length and mitre joint with corner bracket made of polypropylene. Glass shutter should be mitre joint with corner bracket made of CRCA electroplated. Mullion section should be jointed with frame/mullion using nylon. Mullion cap Ethyl Propylene Diamine Monomer(EPDM) gasket should be used all arround glass in shutter between frame and glazed shutter and both sides of fixed glass. Rubber gasket should be used around fly mesh to fix mesh in mesh shutter. Each glazed shutter should be provided with MS powder coated friction hinges 1 (One)set, High grade aluminium coated handles 1(one) number. Each mesh shutter should be provided with S.S. Pivot hinges 1(one)set. Sec-color make handle shall be provided per shutter. Window frame should be fixed to brick/concrete masonary by using nylon self-expanding caps and driving MS electroplated 80mm long screw into the caps through frames complete aincluding entire carriage of material with in all leads and lifts and as per drawings and technical specifications as per direction of Engineer-in-Charge including other incidentals .The rates are inclusive of royality, GST or other taxes imposed by the Government.

Providing and fixing ECO-5000 Series Windows Glass shutter and fixed glass portions should be provided with a glass of 4 (four)millimetres plain float glass complete including entire carriage of material with in all leads and lifts and as per drawings and technical specifications as per direction of Engineer-in-Charge including other incidentals .The rates are inclusive of royality, GST or other taxes imposed by the Government.

Providing and fixing ECO-5000 Series Windows mesh shuter should be provided with a stainless steel 32(thirty bwo) gauge fly mesh of 304 (three hundred four) grades with 144 (one hundred forty four) holes per square inch complete and carriage of material within all leads, lifts and other incidental charges complete including entire carriage of material with in all leads and lifts and as per drawings and technical specifications as per direction of Engineer-in-Charge including other incidentals .The rates are inclusive of royality, GST or other taxes imposed by the Government.

Providing and fixing ECO-5000 Series Windows grill should be provided withgrill made of 10mm (ten) millimetres square M. S.bars welded to at 150mm (One hundred fifty ) millimetres Centre to centre 6mm x 12mm(six millimetre into twelve millimetre) M.S, flat total frill unit should be power coated and fixed to window frame woth screws complete including entire carriage of material with in all leads and lifts and as per drawings and technical specifications as per direction of Engineer-in-Charge including other incidentals .The rates are inclusive of royality, GST or other taxes imposed by the Government.

Providing and fixing ISI marked 35 mm (thirty five millimetre) thick flush door shutters conforming to IS : 2202(Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters made of kitply kutty flush door, industries (swastik) Jawala Samrat Laminate Pvt. Ltd. (Samred) CNC commercial ltd (Shivalik) SR Jindal Ply wood Industries (Prima) with stainless steel butt hinges with necessary screws including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government..

Providing and fixing standred steel section of M.S. angle and flat iron (TATA/SAIL make) for doors , Windows and clerestory window frames manufactured from M.S.Angle iron section 35X35X5 (Thirty five into thirty five into five ) millimetres and MS plate 50 x 4 ( Fifty into four) millimetres including hinges jamb, lock jamb,beed and if required angle thrashold of mild steel angle 50X25 (Fifty into twenty five) millimetres welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5 (two point five) millimetres thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after preteatment of the surface including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals .The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and fixing 19(Ninteen) millimetres thick termite resistant water proof Commercial Board confirming to IS- No.1659 of NOVAPAN , ARCHIDPLY, ACTION TESA,GREEN,NATIONAL,KITPLY make shutters i/c fixing with nickel plated piano hinges with screws etc and PGI sheet linning inside complete upto all floor levels in all heights/ depth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Structural steel work riveted, bolted or welded in built up sections,, made of Tata, Jindal, trusses and trussed, in purlins in building framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. including entire carriage of material with in all leads and lifts upto all floor level and as per drawings and technical specifications as per direction of Engineer-in-Charge including other incidentals .The rates are inclusive of royality, GST or other taxes imposed by the Government.

Steel work welded in built up sections,, made of Tata, Jindal, framed work including cutting hoisting, fixing in position using structural steel etc. as required In Grating frames, guard bar, ladder railing, brackets, gates and similar work. and applying a priming coat of approved steel primer all complete including entire carriage of material with in all leads and lifts upto all floor level and as per drawings and technical specifications as per direction of Engineer-in-Charge including other incidentals .The rates are inclusive of royality, GST or other taxes imposed by the Government.

Providing and fixing M.S.fan clamp type -1(one) of 16 (Sixteen) millimetres) dia M.S. bar bent to shape with hooked ends in R.C.C slab during laying including painting the exposed portion of loop,all as per standard design complete. including entire carriage of material with in all leads and lifts and as per drawings and technical specifications and the direction of Engineer-in-Charge including other incidentals .The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Govt.

Providing and laying 10mm thick Full body vitrified floor tiles of size 600x600 (Six hundred into six hundred millimeters) with water absorption less than 0.08% ( zero point zero eight ) and conforming to IS: 15622, of approved make Somany/Kajaria/Nitco /Orient RAK, Johnson & Johnson) in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm (three point three killogramm per square meters) including grouting the joints with white cement and matching pigments etc., complete upto all floor level in all heights including entire carriage of material with in all leads lifts upto all floor level and as per drawings and technical specifications as per direction of Engineer-in-Charge including other incidentals .The rates are inclusive of royality, GST or other taxes imposed by the Government.

Providing and laying Full body exterior grade vitrified floor tiles of size 600x600x10mm (Six hundred into six hundred into ten millimeters) in matt finished with water absorption less than 0.08% ( zero point zero eight )and conforming to IS: 15622, of approved make Somany/Kajaria/Nitco /Orient RAK, Johnson & Johnson), in all colours and shades, laid on 20mm ( twenty millimetre) thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm (three point three killogramm per square meters) including grouting the joints with white cement and matching pigments etc., upto all floor level in all heights including entire carriage of material with in all leads lifts upto all floor level and as per drawings and technical specifications as per direction of Engineer-in-Charge including other incidentals .The rates are inclusive of royality, GST or other taxes imposed by the Government.

Providing and laying antiskid vetrified tilese (for vision impaired persons as per standards) of size 300 x150x10mm (three hundred into one hundred fifty into ten) millimetre of approved make Somany/Kajaria/Nitco /Orient RAK, Johnson & Johnson)in all colours and shades i laid on a bed 12 mm ( twelve millimetre) thick cement mortar 1:3 ( one cement : three sand) ljointing with grey cement slurry @ 3.3 kg/ sqm (three point three killogramm per square meters) including grouting the joints with white cement and matching pigments etc., upto all floor level in all heights including entire carriage of material with in all leads lifts upto all floor level and as per drawings and technical specifications as per direction of Engineer-in-Charge including other incidentals .The rates are inclusive of royality, GST or other taxes imposed by the Government.

Providing and laying polished marble stone in flooring, 18 (Eighteen) millimetres with semi round nosing stone as per sample of mable approved by Engineer -in - charge over 20mm averege thick base of cement mortar 1:4 (one cement: four sand) laid over and joined with grey cement slurry and with an admixure of pigment to match the shade of marble including rubbing and polishing complete with makrana white second quality 20(twenty) millimetres thick, upto all floor levels in all heights/ depth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. he rates are inclusive of royality, GST or other taxes imposed by the Government.

Providing and fixing MS railing for stair case having balluster of 19mm x19mm ( ninteen into ninteen millimetres) M.S. solid square bar with a clear height of 85cm (eighty five centimetres) embedded in cement concrete steps and jointed with electrical/gas welding at top along with MS flat of 40mmx6mm ( forty into six millimetres) size complete with a applying priming coat of red lead paint as per drawing specification upto all floor levels in all heights/ depth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing and fixing 75mmx60 mm (seventy five millimetre into sixty millimetre) with second class Indian teak wood rounded hand rails in straight lenth complete upto all floor levels in all heights/ depth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing and fixing 0.60mm (Zero point sixty millimetres) thick prepainted steel sheet made of TATA,Durashine in roofing with hot dipped matallic Zinc coated sheet with the top coat of regular modified polyster (RNP) organic coating of 20 (twenty) microns 5 (five) micron over five micron's primer coating to back coat of polyster over 5 (five) microns primar coating including fixing with pre painted iron J or L hooks, bolts and nuts 6mm (six milimeters) dia meter with prepainted limpet and rubber washer complete with all accessories as equired as per the direction of Engineer-in Charge upto all floor levels in all heights/ depth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. he rates are inclusive of royality, GST or other taxes imposed by the Government.

Providing and fixing ridges or hips with proper gola 60cm (Sixty centimetres) overall with 0.60mm) Zero point six zero millimetres) thick prepainted steel sheets made of TATA/Durashine Make in roofing with hot dipped metallic zinc coated sheets with top coat of regular modified polyster organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating plus back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six millimetres) dia and prepainted G.I. limpet and bitumen washer complete with all accessories as required upto all floor levels in all heights/ depth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. he rates are inclusive of royality, GST or other taxes imposed by the Government.

Providing and fixing flushing 38cm(Thirty eight centimeter) overall with 0.60mm ( Zero point six milimetre)thick pre painted sheet made of tata durashine in roofing with hot dipped metallic Zinc coated sheet with top coat of regular modified polyester organic coating of 20 microns over 5 (Five) microns primer coating + back coat of polyster of 5 (Five) microns over 5(Five) microns primer coating i/c fixing with pre painted J or L hooks, bolts and nuts 6(Six milimetre) dia meter & pre painted G.I. limpet & bitumen washers complete upto all floor levels in all heights/ depth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. he rates are inclusive of royality, GST or other taxes imposed by the Government.

Providing and fixing MS BP Sheet 1.66 to 2.00 (One point sixty six to two ) millimetres thick of TATA Dura shine make in eaves board/ facia/ soffits/ ceiling including cutting fixing and welding to steel roof members and applying a coat of red lead primer complete upto all heights as per direction of Engineer in Charge ( base members of steel work shall be measured and paid separtely ) upto all floor levels in all heights/ depth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. he rates are inclusive of royality, GST or other taxes imposed by the Government.

Providing and fixing 8 mm (eight millimetre) thick cement fibre plain multipurpose cement board ( high pressure steam cured) with suitable of Everest /Dexune /Aeolite/Gyproc with butterfly clips and hinges etc. as required pattern complete in all respect upto all floor levels in all heights/ depth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing and fixing 110 mm ( one hundred ten millimetre )dia on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes Supreme, AKG, Finolex, Prince, Kisan, SFMC, Diplast conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten milimetre) gap for thermal expansion complete upto all floor level including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of royality, GST or other taxes imposed by the Government.including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes Supreme, AKG, Finolex, Prince, Kisan, SFMC, Diplast conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten milimetre) gap for thermal expansion complete upto all floor level including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of royality, GST or other taxes imposed by the Government.including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals.

Coulper 110mm ( one hundred ten millimetre)

110 mm ( one hundred ten millimetre) plain bend

110mm ( one hundred ten millimetre)dia uP.V.C. shoe

Providing and fixing 110mm dia (one hundred ten millimetres)PVC clamps ISI marked of Finolex Supreme, AKG, Prince, Kisan, SFMC, Diplast make of approved design with steel screws and rawal plugs etc. Complete upto all floor level including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

15 mm (fifteen milimetre) cement plaster on the fair side of single or half brick wall of mix 1:6 (one cement : six fine sand) complete upto all floor level including entire carriage of material with in all leads and lifts and as per drawings and technical specifications as per direction of Engineer-in-Charge including other incidentals .The rates are inclusive of royality, GST or other taxes imposed by the Government.

15 mm (fifteen milimetre) cement plaster on the rough side of single or half brick wall of mix 1:6 (one cement : six fine sand) complete upto all floor level including entire carriage of material with in all leads and lifts and as per drawings and technical specifications as per direction of Engineer-in-Charge including other incidentals .The rates are inclusive of royality, GST or other taxes imposed by the Government.

6 mm (six milimetre)cement plaster of mix: 1:3 (one cement : three fine sand) complete upto all floor level including entire carriage of material with in all leads and lifts and as per drawings and technical specifications as per direction of Engineer-in-Charge including other incidentals .The rates are inclusive of royality, GST or other taxes imposed by the Government.

Providing and fixing 12mm thick green chalk board (non magnetci with superior quality framing specially anodized aluminium profile 20x15mm with corners of black surface shall be non porous cermaic particle on the top on the green surface for the writing with chalk over 11mm thick particle board which shall have backing material of galavanized sheet 0.28 mm approx. the board clamps upto all floor levels in all heights/ depth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Finishing walls with Two or more coat applied @ 1.43 ltr/10 sqm (One point forty three liters per ten square metre) over and including priming coat of exterior primer applied @ 0.90 liter/10 sqm (zero point nine liters per ten square metre) Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade preparation of surface, etc. complete on undecorated wall surface (two coats) to give an even shade and final finish after thoroughly cleaning the surfaces to remove all dirt dust and other foreign matter etcetera including sand papered smooth complete upto all floor levels in all heights/ depth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Wall painting with premium emulsion paint of approved brand and manufacture ICI (Dulux Gloss, Nerolac, Berger ( Luxal High Gloss) Asian Paints ( Premium Apcolite Gloss Shalimar to give an even shade : Two or more coats on new work upto all floor levels including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Distempering (two or more coats) with over and including water thick made priming coat with cement primer with oil bound washable distemper of approved brand Nerolac , Berger (Bison Acrylic) Asian Paints (Tractor, Acrylic), Shalimar of approved manufacturer, of required shade and colour complete, on new concrete /masonry/plastered surfaces after and including preparing the surface by thoroughly cleaning oil,grease,dirt and other foreign matter and sand papering the surface smooth complete as required upto all floor levels in all heights/ depth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing and applying white cement based putty of average thickness 1 mm ( one millimetre) of approved brand and manufacturer JK wall putty/ Birla white Putty make over the plastered wall surface to prepare the surface even and smooth complete upto all floor level including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm (zero point nine liters per ten square metre)over an under coat of primer applied @ 0.80 ltr/ 10 sqm (zero point eight liters per ten square metre) of approved brand and manufactureICI (Dulux Gloss), Nerolac, Berger (Luxol High Gloss), Asian Paints (Premium Apcolite Gloss), Shalimar make including cleaning the surface of all dirt dust and other forign metter complete upto all floor levels in all heights/ depth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Providing and laying water proofing treatment, by applying cement slurry mixed with water proofing cement compound of Dr.Fixit Padfin or equivalent consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm (zero point four eight eight kilograme per square metre). Mixed with water proofing cement compound @ 0.253 kg/sqm ( zero point two five three kilograme per square metre). This layer will be allowed to air cure for 4 (four) hour. (b) Second layer of slurry of cement @ 0.242 kg/sqm ( zero point two four two kilograme per squaremetre mixed with water proofing cement compound @ 0.126 kg/sqm ( zero point one two six kilograme per square metre). This layer will be allowed to air cure for 4 (four)hours followed with water curing for 48 ( forty eight)hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry upto all floor levels in all heights/ depth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

Making plinth protection 50mm (fifty millimeter) thick in cement concrete 1:3:6 (one cement : three sand (zone - III) : six graded crushed stone aggregate 20mm (twenty millimeter) nominal size) over 75 mm(seventy five millimetres) thick bed of dry brick bllast 40 mm(forty millimetres) nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling and derssing and finishing the top smooth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of royality, GST or other taxes imposed by the Government.

Constructing Coursed rubble hammer dressed 'U' shape open surface drain with side wall. 15 X 23 cm (Fifteen into twenty three centimeter ) in cement mortar 1:6 ( One Cement : Six Sand) and inside plastering with cement mortar 1:3 (One Cement: Three approved Sand) including earth work and laying 10 cm (Ten Centimatre ) cement concrete in 1:5:10 (One Cement : Five approved Sand : Ten graded crushed stone aggregate) of 40 mm (Forty millimetres) nominal size and 7.5 cm (seven Point Five Centimatre ) cement concrete 1:2:4 (One Cement : Two approved Sand : Four graded crushed stone aggregate of 20 mm (Twenty millimetre) nominal size) and finished with a floating coat of neat cement complete as per standard design upto all floor levels in all heights/ depth including entire carriage of material with in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax , GST or other taxes imposed by the Government.

MOHINDER PAL GOVT. CONTRACTOR