Civil and structural works for Tissue Paper Machine (TM#5) complex at TNPL Unit II

Amount

EARTH WORK EXCAVATION IN ALL SOILS AND SUB SOILS EXCLUDING ROCK INCLUDING BACKFILLING IN SIDES OF FOUNDATIONS AND BASEMENT, WATERING, CONSOLIDATION, INCLUDING DEWATERING WHEREVER NECESSARY, ETC., AND DISPOSING OFF THE SURPLUS EARTH WITHIN A LEAD OF 40 MTRS AS DIRECTED IN DEPTH FROM GROUND LEVEL TO -2 MTR.

EARTH WORK EXCAVATION IN ALL SOILS AND SUB SOILS EXCLUDING ROCK INCLUDING BACKFILLING IN SIDES OF FOUNDATIONS AND BASEMENT, WATERING, CONSOLIDATION, INCLUDING DEWATERING WHEREVER NECESSARY, ETC., AND DISPOSING OFF THE SURPLUS EARTH WITHIN A LEAD OF 40 MTRS AS DIRECTED IN DEPTH BELOW -2 MTR TO -4 MTR.

EARTH WORK EXCAVATION IN ALL SOILS AND SUB SOILS EXCLUDING ROCK INCLUDING BACKFILLING IN SIDES OF FOUNDATIONS AND BASEMENT, WATERING, CONSOLIDATION, INCLUDING DEWATERING WHEREVER NECESSARY, ETC., AND DISPOSING OFF THE SURPLUS EARTH WITHIN A LEAD OF 40 MTR AS DIRECTED IN DEPTH BELOW -4 MTR TO -6 MTR.

EXCAVATE AND REMOVE HARD ROCK REQUIRING CONTROLLED BLASTING AT ALL LEVELS (40% TO BE DEDUCTED IN STACK MEASUREMENTS OR ACTUAL EXCAVATED HARD ROCK PRE-MEASUREMENT WILL BE TAKEN INTO ACCOUNT WITHOUT STACKING) INCLUDING DEWATERING AND DISPOSE OFF WITHIN A LEAD OF 40 MTR AS DIRECTED.

INTERCARTING OF THE EXCAVATED EARTH AND REFILLING THE LOW LYING AREA / STACKING THE EARTH INCLUDING LOADING, UNLOADING, SPREADING AND LEVELING ETC., AS DIRECTED UPTO A LEAD OF 2 KM. (25% VOIDS TO BE DEDUCTED IN LORRY/TRACTOR MEASUREMENTS)

EARTH CUTTING, TRANSPORTATION WITHIN THE PREMISES, UNLOADING, SPREADING, LEVELLING AND CONSOLIDATION WITH 10MT ROAD ROLLER TO A LEAD OF 2KM.

SUPPLYING AND FILLING OF EARTH BROUGHT FROM OUTSIDE AREA INCLUDING LOADING, UNLOADING, SPREADING ETC., COMPLETE (25% VOIDS TO BE DEDUCTED IN LORRY / TRACTOR MEASUREMENTS)

CEMENT CONCRETE 1:4:8 USING 25MM DOWN GAUGE BLUE GRANITE AGGREGATE IN FOUNDATIONS, MUD MAT, FLOORING EXCLUDING SHUTTERING BUT INCLUDING RAMMING, LEVELLING, CURING ETC., COMPLETE.

CEMENT CONCRETE 1:3:6 USING 20MM SIZE BLUE GRANITE AGGREGATE FOR FLOORING, PATCH WORKS AND FILLING WORKS AT ALL LEVELS EXCLUDING SHUTTERING BUT INCLUDING RAMMING, LEVELLING, CURING ETC., COMPLETE USING MIXTURE MACHINE.

CEMENT CONCRETE M30 USING 20MM SIZE BLUE GRANITE AGGREGATE FOR ALL CEMENT CONCRETE ITEMS SUCH AS FOUNDATIONS, PEDESTALS, COLUMNS, WALLS, SHELL WALL, FOOTING, RAFT, PLINTH BEAM, ETC., EXCLUDING SHUTTERING BUT INCLUDING LEVELLING, CURING, ETC., COMPLETE BELOW GROUND LEVEL AND UPTO FFL.

CEMENT CONCRETE M30 USING 20MM SIZE BLUE GRANITE AGGREGATE FOR ALL CEMENT CONCRETE ITEMS SUCH AS COLUMN, BEAM, SUNSHADE, SHELL WALL, ROOF SLAB, STAIRCASE ETC., EXCLUDING SHUTTERING BUT INCLUDING LEVELLING, CURING, ETC., COMPLETE ABOVE FFL TO +7 MTR LEVEL.

CEMENT CONCRETE M30 USING 20MM SIZE BLUE GRANITE AGGREGATE FOR ALL CEMENT CONCRETE ITEMS SUCH AS COLUMN, BEAM, SUNSHADE, SHELL WALL, ROOF SLAB, STAIRCASE, ETC., EXCLUDING SHUTTERING BUT INCLUDING LEVELLING, CURING, ETC., COMPLETE ABOVE +7 MTR TO +14 MTR LEVEL.

CEMENT CONCRETE M30 USING 20MM SIZE BLUE GRANITE AGGREGATE FOR ALL CEMENT CONCRETE ITEMS SUCH AS COLUMN, BEAM, SUNSHADE, SHELL WALL, ROOF SLAB, STAIRCASE, ETC., EXCLUDING SHUTTERING BUT INCLUDING LEVELLING, CURING, ETC., COMPLETE ABOVE +14 MTR TO +21 MTR LEVEL.

SUPPLYING AND LAYING OF M30 READY MIX CONCRETE WITH GOOD QUALITY FINE AND COARSE AGGREGATE INCLUDING COST OF 53 GRADE OPC CEMENT, TRANSIT MIXERS AND PUMPING ARRANGEMENTS, COMPACTING USING VIBRATORS, ETC., COMPLETE AT ALL LEVELS.

FORM WORK - WROUGHT AND PUT UP WITH GOOD QUALITY MARINE GRADE PLYWOOD FOR ALL TYPES OF SHUTTERING WORKS LIKE FOOTING, RAFT, PLINTH BEAM, ETC., AS "PLASTER FREE FINISH" BELOW GROUND LEVEL AND UPTO FFL.

FORM WORK - WROUGHT AND PUT UP WITH GOOD QUALITY MARINE GRADE PLYWOOD FOR ALL TYPES OF SHUTTERING WORKS LIKE COLUMN, BEAM, SUNSHADE, SHELL WALL, ROOF SLAB, STAIRCASE, ETC., AS "PLASTER FREE FINISH" ABOVE FFL TO +7 MTR LEVEL.

FORM WORK - WROUGHT AND PUT UP WITH GOOD QUALITY MARINE GRADE PLYWOOD FOR ALL TYPES OF SHUTTERING WORKS LIKE COLUMN, BEAM, SUNSHADE, SHELL WALL, ROOF SLAB, STAIRCASE, ETC., AS "PLASTER FREE FINISH" ABOVE +7 MTR TO +14 MTR LEVEL.

FORM WORK - WROUGHT AND PUT UP WITH GOOD QUALITY MARINE GRADE PLYWOOD FOR ALL TYPES OF SHUTTERING WORKS LIKE COLUMN, BEAM, SUNSHADE, SHELL WALL, ROOF SLAB, STAIRCASE, ETC., AS "PLASTER FREE FINISH" ABOVE +14 MTR TO +21 MTR LEVEL.

FORM WORK IN CIRCULAR / CURVED SURFACES WROUGHT AND PUT UP WITH GOOD QUALITY MARINE GRADE PLYWOOD BY CONVENTIONAL METHOD AND AS "PLASTER FREE FINISH" ETC., BELOW GROUND LEVEL AND UPTO FFL.

FORM WORK IN CIRCULAR / CURVED SURFACES USING GOOD QUALITY OF PLYWOOD BY CONVENTIONAL METHOD, ETC., COMPLETE FROM FFL TO +7 MTR LEVEL.

FORM WORK IN CIRCULAR / CURVED SURFACES USING GOOD QUALITY OF PLYWOOD BY CONVENTIONAL METHOD, ETC., COMPLETE FROM +7 TO +14 MTR LEVEL.

PROVIDING AND FIXING IN POSITION "SLIPFORM" SHUTTERING FOR CIRCULAR CHIMNEY / SILO WALL INCLUDING COST OF SPECIAL SHUTTERING HYDRAULIC JACK, PLATFORM, LIFTING ROD ETC., TO BE PROVIDED BY CONTRACTOR AND RENDERING THE CONCRETE WALLS FROM FFL TO REQUIRED HEIGHT AS PER THE DRAWING.

SUPPLY AND FIXING OF PVC WATER BAR OF 200MM WIDE OF APPROVED MAKE FOR CONSTRUCTION JOINTS AT ALL LEVELS.

PROVIDING OPENING WITH REMOVAL WOODEN FORMWORK OF SIZE UPTO 0.50 SQ.M AREA IN THE SHELL WALL/CONCRETE SLABS AND DE-SHUTTERING AFTER CONCRETING COMPLETE AT ALL LEVELS.

PROVIDING OPENING WITH REMOVAL WOODEN FORMWORK OF SIZE FROM 0.50 SQ.M TO 1.00 SQ.M AREA IN THE SHELL WALL/CONCRETE SLABS AND DE-SHUTTERING AFTER CONCRETING COMPLETE AT ALL LEVELS.

PROVIDING POCKETS FOR FOUNDATION BOLTS USING SUITABLE WOODEN REMOVAL FORMWORK INCLUDING REMOVING THE SAME WHILE THE CONCRETE IS WET AND FIXING THE FOUNDATION BOLTS FOR MACHINERY FOUNDATIONS ETC., THE SIZE VARIES FROM 150 SQ.MM TO 250 SQ.MM OF DEPTH VARYING FROM 400 MM TO 900 MM (ANY INCREASE IN SIZE AND DEPTH OVER THE ABOVE WILL BE CONSIDERED AND PAID FOR PRORATA BASIS).

TAKE DELIVERY OF HIGH STRENGTH RIBBED DEFORMED BARS/ MS BARS ISSUED BY TNPL FREE OF COST, CUT, BEND AND TIE UP IN POSITION INCLUDING COST OF SUPPLYING NECESSARY 18 GAUGE BINDING WIRE FOR ALL TYPES OF RCC WORKS AT ALL LEVELS.

GROOVE CUTTING OF SIZE 40MM DEEP X 6MM WIDTH ON THE RCC FLOOR WITH NECESSARY EQUIPMENT, LABOUR ETC., COMPLETE AS DIRECTED BY ENGINEER IN CHARGE.

PROVIDING COURSED RUBBLE STONE MASONRY WITH POINTING WORKS, SECOND SORT IN CEMENT MORTAR 1:7 WITH THROUGH BOND STONES 2 MTRS APART IN EACH COURSE, PLACED IN A STAGGERED PATTERN AND COURSE NOT LESS THAN 150MM HIGH WITH FACE STONES PLACED HEADERS AND STRETCHERS ALTERNATIVELY TO BREAK JOINTS BY ATLEAST 75MM INCLUDING CURING ETC., COMPLETE FOR FOUNDATION BASEMENT UPTO +1.00 MTR LEVEL.

SUPPLY AND LAYING OF FLY ASH BRICKS IN CM 1:6 IN FOUNDATIONS AND BASEMENT UPTO +0.00 MTR INCLUDING CURING, ETC., COMPLETE.

SUPPLY AND LAYING OF FLY ASH BRICKS IN SUPER STRUCTURE IN CM 1:6 INCLUDING SCAFFOLDING, CURING ETC., COMPLETE ABOVE +0.00 MTR TO +7.00 MTR

SUPPLY AND LAYING OF FLY ASH BRICKS IN SUPER STRUCTURE IN CM 1:6 INCLUDING SCAFFOLDING, CURING ETC., COMPLETE ABOVE +7.00 MTR TO +14.00 MTR

SUPPLY AND LAYING OF FLY ASH BRICKS IN SUPER STRUCTURE IN CM 1:6 INCLUDING SCAFFOLDING, CURING ETC., COMPLETE ABOVE +14.00 MTR TO +21.00 MTR.

PREPARE SURFACES OF WALLS AND PLASTER INTERIOR, EXTERIOR AND TOP FACES WITH CEMENT MORTAR 1:4, 12MM THICK AT ALL LEVELS INCLUDING NECESSARY SCAFFOLDINGS AND CURING ETC., COMPLETE.

SUPPLY OF “READYMIXED” PLASTER OF IDEAL CEMIX-H / DR.PLASTER / DALMIA READYMIX PLASTER OR OTHER EQUIVALENT MAKE AND MIXING WITH REQUIRED QUANTITY OF WATER AND APPLICATION OF 12 MM THICK PLASTER OVER PREPARED SURFACES OF BRICKWALLS, CEILING ETC. INCLUDING SCAFFOLDING, LABOUR, TOOLS AND TACKLES, MATERIAL COST ETC., COMPLETE AT ALL LEVELS.

PROVIDING 12MM X 12MM GROOVE IN BEAM,COLUMN, LINTEL, JOINTS, ETC., WHILE PLASTERING INCLUDING LABOUR, ETC., COMPLETE.

PROVIDING BORDERS WITH CM 1:3, 100MM WIDE, 20MM THICK INCLUDING FINISHING NEATLY, ETC, COMPLETE AT ALL LEVELS.

PREPARE SURFACES AND RUBBING WITH CARBORANDUM STONE AND FILLING THE JOINTS WITH CM 1:3 AND APPLY ONE COAT OF CEMENT WASH AT ALL LEVELS INCLUDING SCAFFOLDING, ETC., COMPLETE.

PREPARE SURFACES OF BASE COURSE BY REMOVING ALL LOOSE MORTAR BY HACKING AND LAY TO REQUIRED SLOPE 50MM THICK GRANO FLOOR OF MIX 1:1.5:3 USING 10 TO 12MM GRANITE CHIPS INCLUDING FINISHING THE TOP LAYER WITH A POWER TROWEL AND FLOOR HARDENER WHICH IS SUPPLIED BY TNPL FREE OF COST AT ALL LEVELS.

PREPARE SURFACES OF CONCRETE FLOORING AND DO POWER TROWLING FINISH AS DIRECTED BY ENGINEER INCHARGE.THE RATE INCLUDES TAKE DELIVERY OF FLOOR HARDNER SUPPLIED BY TNPL ON FREE OF COST AND DOSAGE AT THE RATE OF 4KG/SQ.M WHILE TROWELING.

SUPPLYING AND FIXING OF POLISHED GRANITE SLAB 20MM THICK OF APPROVED COLOUR AND FIX IN POSITION OVER CEMENT SLAB IN CM 1:3, 12 MM THICK AND POINTING THE JOINTS FREE WITH TILE MATT COMPOUND, NOSING OF EDGES, CURING ETC., COMPLETE AS DIRECTED BY ENGINEER IN CHARGE.

TAKE DELIVERY OF 200 X 100 X 20 MM THICK AR TILES AS PER IS 4457 SUPPLIED BY TNPL AT FREE OF COST. SUPPLY AND APPLICATION ONE COAT OF B -100 PRIMER AS PER IS 4832 PART - 2 FOLLOWED BY TILE LAYING WITH 5 MM THICK BEDDING MORTAR AND POINTING THE JOINT WITH 3 MM THICK B - 100 CEMENT.

TAKE DELIVERY OF 200 X 100 X 20 / 12 MM THICK (OR) 300 X 300 X 12MM THICK AR TILES AS PER IS 4457 SUPPLIED BY TNPL AT FREE OF COST. SUPPLY AND APPLICATION OF ONE COAT PRIMER AS PER IS 4832 PART - 2 FOLLOWED BY TILE LAYING WITH 5 MM THICK BEDDING MORTAR AND 3MM THICK POINTING AS DIRECTED BY ENGINEER INCHARGE (BEDDING MATERIALS PROPERTIES AS PER ANNEXURE) MAKE : CUMI / HUNTSMAN / NEO CHEMOFLON"

SUPPLY AND APPLICATION OF TWO COMPONENT CEMENTIOUS ACRYLIC MODIFIED ELASTOMERIC BASED COATING AS SEAMLESS WATERPROOF MEMBRANE APPLIED IN TWO COATS (1.2 MM THICK) OF APPROVED MAKE LIKE THERMAX/BASF/SIKA ETC.,

THOROUGHLY PREPARE SURFACES AND LAY PRESSED CLAY TILES OF SIZE 9"X9" OR 8"X8" AND LAY TO PROPER SLOPE IN CM 1:3, 20MM THICK BED MORTAR MIXED WITH 5% OF CRUDE OIL BY WEIGHT OF CEMENT AND POINTING THE JOINTS WITH THE SAME OILED MORTAR, CURING ETC., COMPLETE AT ALL LEVELS.

PROVIDING AND APPLYING FOSROC MEMBRANE HDPE - P STD, 1.2MM THICK PRE-FORMED AND PRE-APPLIED FULLY BONDED PRESSURE SENSITIVE HDPE MEMBRANES WITH ANTI-STICK COATING & GRANULAR LAYER AS PER MANUFACTURER'S SPECIFICATION, LOOSELY LAID ON PCC WITH A MINIMUM LAP OF 75MM. PCC SURFACE SHOULD BE FREE FROM CAVITIES AND PROJECTING NIBS, SMOOTHLY FINISHED, DRY AND FREE FROM FROST, SURFACE LAITANCE AND CONTAMINATION. STANDING WATER MUST BE REMOVED. THE RAFT SLAB WATERPROOFING MEMBRANE SHALL BE EXTENDED TO THE TOTAL HEIGHT OF RAFT THICKNESS ALONG WITH BLOCK WORK USING HDPE SEALED TAPE WHICH IS EXTENDED UPTO 100MM ON TOP THAT SHALL BE FIXED OVER CURED RAFT CONCRETE AND RETAINING WALL WATERPROOFING SHALL BE LAID ON TOP OF IT AS PER MANUFACTURER RECOMMENDATION. THE HDPE MEMBRANE SHOULD CONFORM TO THE FOLLOWING PARAMETERS. (I) MINIMUM THICKNESS OF HDPE LAYER 800MICRON (II) RESISTANCE TO HYDROSTATIC HEAD GREATER THAN 70M (III) MINIMUM PEEL ADHESION TO CONCRETE 880 N/M (IV) MINIMUM TENSILE STRENGTH 21 MPA (V) MINIMUM PUNCTURE RESISTANCE 800N (VI) MINIMUM ELONGATION 400%

PROVIDING AND LAYING 1.5MM THICK SELF ADHESIVE WATERPROOFING MEMBRANE TOPPED WITH HDPE FILM, FOSROC PROOFEX 3000V FOR RETAINING WALLS, FOOTING INTERNAL AND EXTERNAL SURFACES. THE CONCRETE WALL SURFACE SHALL BE MADE DRY, CLEAN, EVEN AND CHECKED FOR SOUNDNESS. REMOVAL OF OIL, DIRT, LAITANCE AND OTHER CONTAMINANTS BY MANUALLY AND SURFACE SHALL BE FAIRLY SMOOTH FINISH. CHAMFERING THE FLOOR WALL JUNCTIONS WITH CEMENT MORTAR 1:4 ADMIXED WITH NITOBOND SBR @ 2 LITRES PER 50 KG BAG OF CEMENT. PROVIDING AND FIXING PROOFEX 3000V, 1.5MM THICK COLD APPLIED BITUMINOUS WATERPROOFING MEMBRANE OVER THE PRIMED SURFACE WITH SOLVENT BASED BITUMEN PRIMER TORCHSEAL PRIMER M. THE WATERPROOFING MEMBRANE SHALL BE SELF ADHESIVE SHEET MEMBRANE COMPRISING OF A POLYMER MODIFIED BITUMEN LAYER INTERNALLY REINFORCED WITH POLYESTER BONDED TO AN OUTER SURFACE OF CROSS LAMINATED HDPE CARRIER FILM. THE WATERPROOFING SYSTEM SHALL BE TERMINATED ONE FOOT ABOVE THE GROUND LEVEL, SEALED AFTER TAKING THE GROOVES OF 10MM X 10MM AND OVER THE BASE WATERPROOFING MEMBRANE AT THE BOTTOM. THE WATERPROOFING MEMBRANE SHALL HAVE THE FOLLOWING PROPERTIES (I) TENSILE STRENGTH : 3.5 MPA IN LONGITUDINAL AND 3.5 MPA IN TRANSVERSE (ASTM D412) (II) TEAR RESISTANCE - 125 N(ASTM D 4073) (III) LAP ADHESION STRENGTH >3N/MM (ASTM D 1000) (V) RESISTANCE TO HYDROSTATIC PRESSURE OF 60M OF WATER. APPROVED MAKE OF PRODUCTS ARE FOSROC CHEMICALS. THE RATE INCLISIVE OF SCAFFOLDING CHARGES,PLATFORM ETC.,

PROVIDING AND FIXING OF HIGH COMPRESSIVE STRENGTH (NOT LESS 200MPA) DIMPLE BOARD OF 8MM THICK AS PROTECTIVE MEDIUM BEFORE SOIL FILLING. THE RATE INCLISIVE OF SCAFFOLDING CHARGES,PLATFORM ETC.,

PROVIDING OF CONPLAST CRYSTALLINE INTEGRAL WATERPROOFING ADMIXTURE (FOSROC) ,RECOMMENDED MINIMUM DOSAGE 0.80% BY WEIGHT OF TOTAL CEMENTIOUS CONTENT /CUBIC METER OF CONCRETE, AND AS PER THE MANUFATURERS SPECIFICATION. THIS IS TO BE MIXED WITH CONCRETE AT BATCHING PALNT ( MEASUREMENT SHALL BE FOR LAID AND COMPACTED CONCRETE QTY).

PROVIDING OF AURAMIX BCI ORGANIC BIPOLAR CONCRETE PENETRATING CORROSION INHIBITING ADMIXTURE. (FOSROC) ,RECOMMENDED DOSAGE 2KG/ CUM OF CONCRETE AND AS PER THE MANUFACTURERS SPECIFICATION. THIS IS TO BE MIXED WITH CONCRETE AT BATCHING PALNT ( MEASUREMENT SHALL BE FOR LAID AND COMPACTED CONCRETE QTY).

SUPPLYING AND FIXING IN POSITION OF MS WINDOW GRILL USING 12MM MS SQUARE BARS / MS FLATS / ROUNDS INCLUDING NECESSARY WELDING AND APPROVED DESIGN INSTRUCTED BY ENGINEER INCHARGE INCLUDING APPLYING ONE SHOP COAT OF RED OXIDE PRIMER ETC., COMPLETE.

SUPPLYING AND FIXING OF APPROVED COLOUR COATED ALUMINIUM WINDOW (SLIDING TYPE ) OF FRAME SIZE 63MM X 45MM X 1.5MM THICK WITH NECESSARY LOCKING ARRANGMENT, RUBBER GASKET, BEADING ETC., INCLUDING 5MM THICK PLAIN GLASS FOR THE SAME (MAKE JINDAL OR INDAL SECTION).

TAKE DELIVERY OF FOUNDATION BOLTS SUPPLIED BY TNPL AT FREE OF COST OF SIZE VARYING FROM M16 / M20 / M25 / M30 / M36 X 750 TO 1000 MM LONG FABRICATE TEMPLATES AND FIXING IN POSITION TO PROPER ALIGNMENT AND LEVEL. THE WORK INCLUDES WELDING TO THE EXISTING MAIN REINFORCEMENT AND TO THE ADDITIONAL REINFORCEMENTS AS ANCHORAGE TO THE FOUNDATION BOLTS AS DIRECTED BY THE SITE INCHARGE.

TAKE DELIVERY OF MS - T - BAR AND FIX IN POSITION INLINE, LEVEL AND ACCURATE DIMENSION ON THE RCC SOLE BEAM WITH THE ADDITIONAL WELDING ETC., AS PER MACHINE SUPPLIER INSTRUCTION.

TAKE DELIVERY OF STRUCTURAL STEEL SUPPLIED BY TNPL FREE OF COST, REMOVE BENDS IF ANY,FABRICATE AS BUILT UP COLUMN, BEAM, ROOF TRUSS & ROOF MONITOR, PURLIN, ETC., AND ERECT IN POSITION WITH MOBILE CRANE OR DERRICK AT ALL LEVELS, INCLUDING COST OF ALL CONSUMABLES LIKE GAS, STANDARD WELDING RODS, BOLTS & NUTS, TOOLS & TACKLES, SCAFFOLDING,ETC., COMPLETE. (AS PER DRAWING)

ERECTION OF SCAFFOLDING AND CLEANING THE SURFACES OF STRUCTURAL MEMBERS USING WIRE BRUSH, EMERY SHEETS AND APPLY ONE COAT OF RED OXIDE PRIMER OF APPROVED QUALITY AND TWO COATS OF SYNTHETIC ENAMEL PAINT OF EITHER BERGER,ASIAN, SHALIMAR, ICI DULUX OR EQUIVALENT (INDUSTRIAL QUALITY) OF APPROVED COLOUR INCLUDING COST OF ALL MATERIALS,PAINT AND ALL OTHER INCIDENTAL CHARGES ETC.,COMPLETE AT ALL LEVELS.

TAKE DELIVERY OF MS PLATE, MS ANGLES FOR FABRICATION AND FIXING IN POSITION INCLUDING WELDING WITH REINFORCEMENT BARS AS INSERTS/NOZZING ANGLES IN CONCRETE FLOORS, BEAMS, COLUMNS, WALLS, SLABS ETC., COMPLETE AT ALL LEVELS.

TAKE DELIVERY OF DECK SHEET (GI/MS) SUPPLIED BY TNPL AT FREE OF COST AND FIX IN POSITION AS PERMANENT SHUTTERING FOR CONCRETE FLOOR AT ALL LEVELS ON THE EXISTING STEEL SUPPORTS AND WELDING ETC., COMPLETE.

SUPPLY OF M20 ANCHOR FASTENER BOLT OF STANDARD LENGTH OF 150MM AND NUT (SOLID TYPE) "HILTI" MAKE AND FIXING IN THE FLOOR, COLUMN FACE, SIDE WALLS, ETC., AT ALL LEVELS INCLUDING DRILLING, LADDER AND SCAFFOLDING ETC., COMPLETE.

SUPPLY OF M16 ANCHOR FASTENER BOLT OF STANDARD LENGTH OF 150MM AND NUT (SOLID TYPE) "HILTI" MAKE AND FIXING IN THE FLOOR, COLUMN FACE, SIDE WALLS, ETC., AT ALL LEVELS INCLUDING DRILLING, LADDER AND SCAFFOLDING ETC., COMPLETE.

SUPPLY OF M12 ANCHOR FASTENER BOLT OF STANDARD LENGTH OF 150MM AND NUT (SOLID TYPE) "HILTI" MAKE AND FIXING IN THE FLOOR, COLUMN FACE, SIDE WALLS, ETC., AT ALL LEVELS INCLUDING DRILLING, LADDER AND SCAFFOLDING ETC., COMPLETE.

TAKE DELIVERY OF GI / MS PIPE TO FABRICATE AND ERECT IN POSITION AT ALL LEVELS, AS HANDRAILS USING 25, 32, 40 AND 50MM DIA GI / MS PIPE. HANDRAILS SHALL BE VERTICAL POSTS OF ONE METRE HEIGHT IN PIPE AT AN INTERVAL OF ONE METRE AND TWO HORIZONTAL RAILING ONE AT THE TOP OTHER AT THE MIDDLE OF THE POSTS. THE COST INCLUDES ONE COAT OF RED OXIDE PRIMER AND TWO COATS OF SYNTHETIC ENAMEL PAINT OF APPROVED COLOUR AND MAKE, ETC., COMPLETE.

TAKE DELIVERY OF "BARE GALVALUME SHEET"/AC SHEET SUPPLIED BY TNPL FREE OF COST AND FIX IN POSITION AS ROOF WITH SELF DRILLING CORROSHIELD MAKE FASTENERS AND EPDM WASHER ETC AS DIRECTED,ETC., COMPLETE AT ALL LEVELS INCLUDING NECESSARY SCAFFOLDING.

TAKE DELIVERY OF "GALVALUME" FLASHING SHEET / BARGE BOARD / RIDGE SHEET, SUPPLIED BY TNPL FREE OF COST AND FIX IN POSITION WITH SELF DRILLING CORROSHIELD MAKE FASTENERS AND EPDM WASHER ETC AS DIRECTED, ETC., COMPLETE AT ALL LEVELS.

TAKE DELIVERY OF "COLOUR COATED GALVALUME SHEET" SUPPLIED BY TNPL FREE OF COST AND FIX IN POSITION AS VERTICAL CLADDING WITH SELF DRILLING CORROSHIELD MAKE FASTENERS AND EPDM WASHER ETC AS DIRECTED, ETC., COMPLETE AT ALL LEVELS INCLUDING NECESSARY SCAFFOLDING.

SUPPLY OF 2MM THICK POLY CARBONATE (SKY LIGHT) AND FIXING IN POSITION FOR ROOF AND SIDE CLADDING WITH SELF TAPPING SCREW AND EPDM WASHER ETC., UPTO +23M LEVELS.(ONLY LAID AREA SHALL BE MEASURED AND PAID)

SUPPLY AND FIXING OF WELD MESH OF SIZE 25X25 MM ( 1” X 1”) SQUARE MADE OUT OF MS ANGLE OF SIZE 40X40X5MM AND ANCHORING WITH FASTENER BOLT AT ALL LEVELS AS PER SKETCH INCLUDING PAINTING ETC., COMPLETE.

PREPARE SURFACES AND APPLY TWO COATS OF WHITE WASH USING APPROVED MAKE INCLUDING MIXING WITH SUFFICIENT QUALITY OF GUM LIKE FEVICOL ETC., COMPLETE AT ALL LEVELS.

ERECTION OF SCAFFOLDING AND CLEANING THE SURFACE OF STRUCTURAL MEMBERS USING WIRE BRUSH, EMERY SHEETS AND APPLY ONE COAT OF RED OXIDE PRIMER OF APPROVAL QUALITY AND TWO COATS OF SYNTHETIC ENAMEL PAINT OF EITHER BERGER, ASIAN, SHALIMAR, ICI DULEX OR EQUIVALENT (INDUSTRIAL QUALITY) OF APPROVED COLOUR INCLUDING COST OF ALL MATERIALS, PAINT AND ALL OTHER INCIDENTAL CHARGES ETC., COMPLETE AT ALL LEVELS.

THROUGHLY PREPARE THE SURFACES AND APPLY ONE COAT OF WALL PRIMER OF APPROVED MAKE OVER WALL PUTTY SURFACES AND APPLY TWO COATS OF ACRYLIC EMULSION IST QUALITY OF APPROVED COLOUR AND MAKE INCLUDING MATERIAL COST AND ALL CONSUMABLES LABOUR CHARGES, SCAFFOLDING ETC. COMPLETE AT ALL LEVELS.

SUPPLY AND APPLICATION OF ONE COAT OF WEATHER PROOF EXTERIOR PRIMER AND TWO COATS OF EXTERIOR EMULSION OF APPROVED COLOUR SHADE INCLUDING SCAFFOLDING, LABOUR ETC., COMPLETE AT ALL LEVELS. (ASIAN OR BERGER).

SUPPLYING AND FIXING OF 25MM THICK EXPANDABLE FILLER BOARD HD 100 JOINTS AT ALL LEVELS (SUPREME MAKE)

PROVIDING ANTI-TERMITE TREATMENT AS PER IS 6313 WITH THE TERMITICIDES CURRENTLY ALLOWED UNDER THE INSECTICIDES ACT 1968 BY THE INSECTICIDES BOARD INCLUDING COST OF TERMITICIDES OF IS STANDARD, LABOUR, ETC., THE CHLOROPYRIFOS OR IMIDACCOPRID MIXED WITH WATER AS PER MANUFACTURER SPECIFICATION - DRILLING HOLE 12MM DIA AT THE JUNCTION OF FLOOR & WALLS, 150MM DEEP AT 300MM INTERVAL IN THE CONCRETE FLOOR INSIDE / OUTSIDE AS THE CASE MAY BE TO REACH THE SOIL BELOW AND FILL DILUTED CHEMICALS.

SUPPLY OF POLYSHULPHIDE GUN GRADE SEALENT OF SIKA / ARADITE / ENDURA / BASF / DEMECH OF APPROVED COLOUR AND SHADE, APPLY THE POLYSHULPHIDE SEALENT FOR FLOOR EXPANSION JOINT 25MM WIDE 25MM DEPTH COST INCLUDES SURFACE PREPERATION AL TOOLS AND TACKLES AS DIRECTED COMPLETE AT ALL LEVELS.

SUPPLY AND FIXING OF STANDARD ISI MAKE 110 MM DIA 4KG/SQ.CM PVC RAIN WATER PIPE INCLUDING NECESSARY CLAMPS AT 1MTR INTERVAL, SWAN NECK, BENDS, SHOES, TW BLOCK ETC., COMPLETE AT ALL LEVELS INCLUDING NECESSARY SCAFFOLDING ARRANGEMENTS BY USING MS PIPE AND COUPLINGS.

FOR SMALL WORKS WHICH IS UNQUANTIFIED EXACTLY, SUPPLY OF ELECTRICAL CONCRETE BREAKER (HILTI MAKE -MODEL NO.1000ADR) WITH LABOUR FOR DISMANTLING OF CONCRETE, BRICK WORK, CR MASONRY, ETC., THE WORK INCLUDES DISPOSAL OF DISMANTLED DEBRIS WITHIN THE LEAD OF 2KM APART AS DIRECTED.

ALIGNMENT USING TOTAL STATION OF EOT CRANE PARALLEL GIRDERS WITH NECESSARY SIM PLATES, LABOUR, TOOLS AND TACKLES ETC., COMPLETE WITH PROTOCOL TO AN ACCURACY OF +/-5 MM AT ALL LEVELS AS PER DRAWING.

TAKE DELIVERY OF CONBEXTRA GP2 OR EQUIVALENT AND MIX WITH 6MM CHIPS 30% FOR GROUTING OF POCKETS INCLUDING CLEANING, SHUTTERING, COMPACTION, CURING, ETC., COMPLETE AT ALL LEVELS.

Bidder Name

Amount in Words

PRIYA ENGINEERING PROJECTS PRIVATE LIMITED (BID ID -1167924)

GANNON DUNKERLEY AND CO LTD (BID ID -1172035)

GANNON DUNKERLEY AND CO LTD (BID ID -1172035)