C/O Sanskriti Sadan at Motipur Distt.Mandi HP

Amount

Excavation in foundation, trenches, etc in earth work in all kinds of classification, of soils such as pick work, jumper work, blasting work saturated soils including chiseling or any other mixed variety of soils, dewatering and / or removal of slush and other incidentals, lift up to any height stacking excavated soil up to all leads and lifts clear from the edge of excavation and then returning the stacked soil in 15cm (fifteen centimetre) thick layer when required into plinths, sides of foundation etc consolidating each deposited layers by ramming and watering and then disposing of all surplus excavated earth to the disposal point within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and laying cement concrete 1:3:6 ( one cement : three sand : six graded, crushed stone aggregate 40mm (forty millimetre) nominal size) mechanically mixed and curing complete excluding cost of form work in foundation and plinth including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and laying cement concrete 1:5:10 ( one cement : five sand : ten graded, crushed stone aggregate 40mm (forty millimetre) nominal size) mechanically mixed and curing complete excluding cost of form work in retaining wall including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and laying in position machine batched and machine mixed design mix M-30 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability above plinth level and upto all floor level as per direction of Engineer-incharge with in all leads, lifts and other incidentals.

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc as per direction of Engineer-in-charge with in all leads, lifts and other incidentals

Centering and Shuttering including struting, propping etc and removal of from all heights in Suspended floors, roofs, landings, balconies and access platform etc as per direction of Engineer-in-charge with in all leads, lifts and other incidentals

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Edges of slabs and breaks in floors and walls etc as per direction of Engineer-in-charge with in all leads, lifts and other incidentals

Providing Tor Steel reinforcement for RCC work hot rolled deformed bars as per direction of Engineer-in-charge including carriage of material with in all leads, lifts and other incidentals

Providing and Fixing in position Expansion joints 15cm (fifteen centimetre) average width made of suitable materail as per design and site requirement as directed by the Engineer- in - charge with in all leads lift and carriage of material and other incidentals

Providing and Fixing 15 cm (fifteen centimetre) wide sheet covering witth aluminiumn flueted strips 3.15 mm (three point fifteen millimetre) thick over expansion joint with iron screws as per design to match the colour/shade of wall treatment as per direction of Engineer in charge with in all leads, lifts and other incidentals

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (one cement : six coarse sand : twelve graded stone aggregate 20 mm (twenty millimetre) nominal size) upto plinth level with in Cement mortar 1:6 (one cement : six coarse Sand) including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Stone filling behind retaining wall as per direction of Engineer in charge including leads, lifts and other incidentals

Providing Weep holes in stone masonry/brick masonry/plain reinforced concrete abutments with 100mm (one hundred millimetre) PVC Pipe with slope of 1:20 as per direction of engineer in charge with in all leads, lifts and carriage of materials and other incidentals.

Providing and fixing structural glazing fabricated from Roll formed sections made of pre-painted steel/powder coated (Base steel as per IS-513 of ‘D’ quality, galvanized as per IS-277 with zinc of 120gm/sqm (one hundred twenty gram/ square metre)) with total coated thickness of 0.72mm (zero point seventy two millimetre). The glass holding section made of 304 grade stainless steel of 0.58mm (zero point fifty eight) thick. The vertical section should be of 50mmx100mmx0.72mm (fifty millimetre into one hundred millimetre into zero point seventy two millimetre), 33mmx58mmx0.72mm (thirty three millimetre into fifty eight millimetre into zero point seventy two millimetre) for frame horizontal section, stiffener section should be 48mmx98mmx1mm (forty eight millimetre into ninety eight millimetre into one millimetre), cover profile sections should be of 20mmx58mmx0.58mm (twenty millimetre into fifty eight millimetre into zero point fifty eight millimetre), glass holding section should be of 37mmx37mm (thirty seven millimetre into thirty seven millimetre) and 37mmx18mm (thirty seven millimetre into eighteen millimetre). Coated section should be painted with primer coat with epoxy primer of 5-7 (five to seven) microns thick, finished coat painted with a polyester paint of 12-16 (twelve to sixteen) microns and back coated with Alkyd backer of 5-7 (five to seven) microns or powder coated with pure polyester powder up to 50-60 (fifty to sixty) microns thick. Galvanized steel sections are to be sued as stiffeners inside the colour coated steel/powder coated sections as per the design requirement to suit wind pressures as given in IS-875. Brackets made of CRCA powder coated/Electroplated should be used to connect vertical to horizontal, vertical to slab, to fix verticals at top & bottom as per site requirement. Gasket made of Ethyl Propylene Diamine Monomer. Natural cure, with Good U.V. Resistance Silicon to be used. Wall fixing of sections to concrete/masonry wall should be with self-expanding cap & screws. All structural glazing work to be executed strictly as per design and drawings and as per direction of Engineer-in-charge with in all leads, lifts and carriage of materials and other incidentals

Providing and fixing top hung shutter in structural glazing from Roll formed sections made of Pre-painted Steel / Powder coated (Base steel as per IS-513 of ‘D’ quality, galvanized as per IS-277 with Zinc of 120 Gm/Sqm (one hundred twenty grams/square metre)) with total coated thickness of 0.72mm (zero point seventy two millimetre). The glass holding section made of 304 grade stainless steel of 0.58mm (zero point fifty eight) thick. Galvanized steel sections are to be used as stiffeners inside the colour coated steel/powder coated sections as per the design requirement to suit wind pressures as given in IS-875. Primer coat with epoxy primer of 5-7 (five to seven) microns thick and back coated with Alkyd backer of 5-7 (five to seven) microns or powder coated with pure polyester powder up to 50-60 (fifty to sixty) microns thick. The outer frame should be of 20mmx58mmx0.58mm (twenty millimetre into fifty eight millimetre into zero point fifty eight), Shutter section should be of 58mmx33mmx0.72 mm (fifty eight millimetre into thirty three millimetre into zero point seventy two millimetre), stiffener section should be 55mmx31mmx1mm. EARL Bihari Hinges – 2 (two) Nos for each shutter and Aluminum Stays – 2 (two) Nos. for each shutter, Aluminum Handle – 1(one) no. for each shutter. Work to be executed strictly as per design and drawings and as per direction of Engineer-in-charge with in all leads, lifts and carriage of materials and other incidentals

Providing and fixing of Sound Barrier with Taper edge size 600x1200x25mm having an absorption coefficient 0.98 at 3.15k Hz and STC of 32 as per ISO: 354-1985 and ISO 140 a, Density 650 Kg/m3, meets stringent Fire Ratings ASTM D- 876 and BS:476, weather resistance as per IS 3308, Thermal Insulation as per IS:3346- 1980 with relative humidity of 90% RH at 60o Celcius(140o Farenhite) for 15 days= No deterioration. Conforms to En 131682001 and are RoHS Complaint. To be installed on G.I studs 600x600mm centre to centre 2400mm X 50mm web thickness 0.5mm, flanges 15 & 50mm fully knurled giving it high strength, hot dipped galvanized steel with 120GSM zinc coating specially designed for Acoustic vibration management and long life with a backing of HIMALYAN ACOUSTICS. 50mm thick,1000 GSM absorb wool tested as per Fire Retardant ASTMD 635-1991/Insulation and IS 15061-2002 for excellent results with in all leads, lifts and carriage of materials and other incidentals.

Providing and fixing of Himalyan Acoustics ‘’ Woodlot’’ FR Grades 2430x131x12mm (two thousand four hundred thirty into one hundred thirty one into twelve millimetre) made of exterior grade HDF backed with acoustical Fleece providing sound absorption of 0.70 (zero point seventy) NRC as per ISO 354.the panels come with tongue & groove for seamless patterns,4-28mm (four to twenty eight millimetre) Groove and visible panel. These slats are made from acoustical fibreboard with linear perforations for excellent uniformity. The perpendicular holes are available on the back of panel which are covered by black acoustical fleece. Achieves sound reduction of 0.70 (zero point seventy) NRC. The density per panel is 750-800 kg/m3 (seven hundred fifty to eight hundred kilogram/cubic metre). To be installed on FR Sound Prood Ply 12mm (twelve millimetre) thickness with size 2400x1220 mm (two thousand four hundred into one thousand two hundred twenty millimetre) . To be installed on G.I studs 600x600mm (six hundred into six hundred millimetre) centre to centre 2400mm X 50mm (two thousand four hundred millimetre into fifty millimetre) web thickness 0.5mm (zero point five millimetre), flanges 15 & 50mm (fifteen and fifty millimetre) fully knurled giving it high strength, hot dipped galvanized steel with 120GSM zinc coating specially designed for Acoustic vibration management and long life with a backing of HIMALYAN ACOUSTICS. 50mm (fifty millimetre) thick,1000 (one thousand) GSM absorb wool tested as per Fire Retardant ASTMD 635-1991/Insulation and IS 15061-2002 for excellent results with in all leads, lifts and carriage of materials and other incidentals.

Providing and fixing ECO-5000 Series Windows fabricated from roll formed sections made of Galvanized Steel colour coated/powder coated (Base steel as per IS513 “D” quality Galvanized as per IS 277 with Zinc of 120gm (one hundred twenty grams) per square metre with total coated thickness of 0.60mm (zero point six millimetre). Section for frame should be of 98x50mm (ninety eight into fifty millimetre) section for Mullion should be of 46x70mm (forty six into seventy millimetre), section for shutter frame should be of 46x46mm (forty six into forty six millimetre), section for fixed glass bead should be of 18x25mm (eighteen into twenty five millimetre) and section for fly mesh shutter frame should be of 20x40mm (twenty into forty millimetre) as per specificaton and direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing door frame single rebate fabricated from sections roll formed out of 1.2mm (one point two millimetre) thick galvanized steel (Base steel as per IS 513) with zinc of 120gms/sq.mtr. (one hundred twenty grams per square metre). The overall size of the section should be 80x50mm & 105x60mm (eighty into fifty millimetre & one hundred five into sixty millimetre) with rebate of 37mm (thirty seven millimetre) for shutter. The frame section should be cut to length and meter joined with corner brackets made of CRCA electroplated. The frame should be provided with (a) 3 (three) Nos. of M.S powder coated 4" Butt hinges of 2mm (two millimetre) thickness welded to the frame. (b) 6 (six) Nos of 1.2 mm (one point two millimetre) thick CRCA electroplated stiffeners should be welded to frame. (c) 6 (six) Nos of 8" M.S hold fasts with split end tail welded to stiffener plates. (d) On no. altrop receiver. (e) Each frame should be provided with 25x50mm (twenty five into fifty millimetre) tie rod at bottom. All welded places should be treated with protective coat of zinc rich primer. The entire frame should be provided with a coat of etched primer including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in-charge and specification.

Providing and fixing M.S. grill of required pattern in wooden/steel frames of windows etc. with M.S. flat square or round bars with powder coated and fixed to window frame with screws including carriage of materials with in all lead, lifts and other incidentals as per direction of Engineer-in-Charge and as per specification.

Providing and fixing stainless steel 32 (thirty two) gauge fly mesh of 304 (three hundred four) grades with 144 (one hundred forty four) holes per square inch. including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing of protrack spandex system on G.I studs 2400mm X 50mm (two thousand four millimetre into fifty millimetre) web flanges 15 & 50mm (fifteen and fifty millimetre) fully knurled giving it high strength, hot dipped galvanized steel with 120GSM zinc coating specially designed for Acoustic vibration management and long life with a backing 50mm (fifty millimetre) thick Rock wool @ 48kg (forty eight kilogram) density insulation intact with chicken mess wires. 600x1200x15mm (six hundred into one thousand two hundred into fifteen millimetre) Magnetite pine wool tile with NRC 0.9- 1 to be mechanically fastened on the G.I Studs. Then 12mm (twelve millimetre) clip rails system re screw fixed on to the 12 mm (twelve millimetre) MDF waterproof and Acoustics panels. Then the Spandex is stretched over the clip rail system. The installed system should provide NRC OF 1.00. Spandex color as per Architect Choice-Ref attached specifications for more details. The system to be installed on G.I studs 600x600mm (six hundred into six hundred millimetre) center to center 2400mm X 50mm (two thousand four hundred millimetre into fifty millimetre) web thickness 0.5mm (zero point five millimetre) , flanges 15 & 50mm (fifteen and fifty millimetre) fully knurled giving it high strength, hot dipped galvanized steel with 120GSM zinc coating specially designed for Acoustic vibration. MAKE: ECOPHON/PROLAD/BAUX. Work to be execution strictly as per design and drawings and to the satisfaction of Engineer-in-charge with in all leads, lifts and carriage of materials and other incidentals

Providing and Fixing Stainless steel handles 150mm (one hundred fifty millimetre) of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and Fixing Stainless steel Tower bolts 300x10 mm (three hundred into ten millimetre) of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and Fixing Stainless steel Tower bolts 200x10 mm (two hundred into ten millimetre) of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and Fixing SS sliding door bolt of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

200 x 16mm (two hundred into sixteen millimetre)

300 x 16mm (three hundred into sixteen millimetre)

Providing and fixing 150 mm (one hundred fifty millimetre) bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and Fixing 12mm (twelve millimetre) thick toughned glass in boundary wall of approved quality including carriage of material with all leads, lifts and other incidentals as per direction of Engineer in charge

Providing and fixing panelled or panelled and glazed shutters for doors windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) with in all leads, lifts and carriage of materials and other incidentals.

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm (twenty five millimetre to forty millimetre) thick Second class teak wood with in all leads, lifts and carriage of materials and other incidentals.

Providing and Fixing 5.5MM (five point five millimetre) THICK GLASS PANES with putty complete as per direction of Engineer in charge including carriage of material with all leads lifts and other incidentals

Providing and Fixing ISI Marked butt hinges of heavy duty complete as per direction of Engineer in charge including carriage of material with all leads lifts and other incidentals

Providing and Fixing 35mm (thirty five millimetre) thick ISI marked Flush door shutters conforming to IS 2202 decorative type of 1st class hard wood of approved quality including carriage of materials within all leads, lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) with in all leads, lifts and carriage of materials and other incidentals.

Providing and fixing stainless steel (grade 304) railing made of Hollow tubes, channels, plates etc. including welding, grinding, buffing, polishing and making curvature (wherever required and fitting the same with necessary stainless-steel nuts and bolts complete, including fixing 12mm (twelve millimetre) thick toughened glass of specified length and height as provided in the approved drawing including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size on the top of the floor or side of the waist slab with suitable arrangement as per approval of Engineer-in-charge with in all leads, lifts and carriage of materials and other incidentals

Steel work in built up tubular section, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works with in all leads, lifts and carriage of materials and other incidentals.

Strengthening of 4 (four) Nos end joints of 2 (two) Nos I Girder for bridge on 3rd & 4th floor (two joints in each girder) by inserting 4 Nos M-30 Hilti bolts 4.6 grade 300 mm (three hundred millimetre) long (minimum ) into RCC of shear and lift walls in each joint (total bolts 4x4 = 16 Nos) using HIT-HY-200R chemical or equivalent to make the each joint perfect as per design and drawings and strictly to the satisfaction of Engineer - in- charge with in all leads, lifts and carriage of materials and other incidentals.

Providing and laying digital wall tiles 300x600x8mm (three hundred into six hundred into eight millimetre) in grey/colored or of approved shade in dado laid on a bed of 12mm (twelve millimetre) thick cement mortar 1:3 (one cement : three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete including form work including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying Duro stone vertified tiles 300x300mmx10mm (three hundred into six hundred into ten millimetre) in grey/colored or of approved shade in laid on a bed of 12mm (twelve millimetre) thick cement mortar 1:3 (one cement : three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete. Including form work including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm (three hundred into three hundred into nine point eight millimetre) having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm (twenty millimetre) thick base of cement mortar 1:4 (one cement : four coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge with in all leads, lifts and carriage of materials and other incidentals.

Providing and Fixing on wall faces 110mm (one hundred ten millimetre) dia PVC rain water pipes of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and Fixing on wall face PVC rain water accessorie PVC Plain Bend 100mm (one hundred millimetre) dia of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

15mm (fifteen millimetre) thick Cement plaster in 1:4 (one cement: four Fine sand) finished with a floating coat of neat cement as per direction of Engineer-in-charge with in all leads, lifts and other incidentals

12mm (twelve millimetre) thick Cement plaster in 1:4(one cement: four Fine sand) finished with a floating coat of neat cement as per direction of Engineer-in-charge with in all leads, lifts and other incidentals

Providing and applying white cement based putty of average thickness 1mm (one millimetre) of approved brand and maufactured over the plastered wall surface to prepare the surface even and smooth complete with in all leads, lifts and carriage of materials and other incidentals.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 (fifty grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour with in all leads, lifts and carriage of materials and other incidentals.

Priming With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works with in all leads, lifts and carriage of materials and other incidentals.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade Two or more coats on new work with in all leads, lifts and carriage of materials and other incidentals.

Polishing two coats with malamine polish with in all leads, lifts and carriage of materials and other incidentals.

Providing and Fixing stainless steel grade 304 Exhaust Hood (Chimney) as per direction of Engineer-in-charge including carriage of material with in all leads and lifts and other incidentials.

Providing and Fixing Stainless steel grade 304 Duct for chimney including fixing on wall face firmly with suitable clamps as per direction of Engineer - in- charge including carriage of material with in all leads and lifts and other incidentals

Providing and Fixing Exhaust Fan (18'' size) of approved quality as per direction of Engineer-in-charge including carriage of material with in all leads and lifts and other incidentals

Providing and Fixing Stainless steel Helping Table as per direction of Engineer-in-charge including carriage of material with in all leads and lifts and other incidentials.

Providing and Fixing Cooking range made up of stainless steel as per direction of Engineer-in-charge including carriage of material with in all leads and lifts and other incidentials.

Providing and Fixing Stainless steel Working Table with two O.H.S (Overhead shelf) as per direction of Engineer-in-charge including carriage of material with in all leads and lifts and other incidentials.

Providing and Fixing Stainless steel Mixee Station with two O.H.S (Overhead shelf) as per direction of Engineer-in-charge including carriage of material with in all leads and lifts and other incidentials.

Providing and Fixing Stainless steel Pick up Table with two O.H.S (Overhead shelf) as per direction of Engineer-in-charge including carriage of material with in all leads and lifts and other incidentials.

Providing and Fixing LPG Fitting as per direction of Engineer-in-charge including carriage of material with in all leads and lifts and other incidentials.

Providing and Fixing Gas Bank made up of Mild steel as per direction of Engineer-in-charge including carriage of material with in all leads and lifts and other incidentials.

Providing and fixing wall hung WC with UF Seat cover, Hinges, Accessories Set complete set Size 515 X 355X365mm (five hundred fifteen into three hundred fifty five into three hundred sixty five millimetre) complete of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals

Providing and fixing one set Crane consists of EWC P Concealed size 740X520X835mm, one No. of cistern , one No. of seat cover , one No. of wash basin size 450X300mm (four hundred fifty into three hundred millimetre), two No. of Grab Bars, Hinged rail and one No. of Faucet with spatula lever complete of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals

Providing and fixing one one Piece EWC with S-Trap & integrated cistern, including seat cover and Twin flush fittings of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm (one hundred millimetre) sand cast Iron P or S trap, 10 (ten) litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm (five hundred eighty into four hundred fourty millimetre) with integral type foot rests of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and fixing Slim consealed cistern with floor mounting frame and installation kit with flush control plate of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and fixing wash basin with fixing accessories size 470X575X190mm (four hundred seventy into five hundred seventy five into one hundred ninety millimetre) with half pedestal of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and fixing wash basin with C.I. brackets, 15 mm (fifteen millimetre) C.P. brass pillar taps, 32 mm (thirty two millimetre) C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 550x400 mm (five hundred fifty into four hundred millimetre) with a pair of 15 mm (fifteen millimetre) C.P. brass pillar taps of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and fixing stainless steel kitchen sink size 610 X 460 X 200mm(Six hundred ten into four hundred sixty into two hundred millimeter) of approved standard ISI make of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and fixing Vitreous China Urinal Flat Back Star white with all fittings and accessories of size 375x390x590mm (three hundred seventy five into three hundred ninety into five hundred ninety millimetre) of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and fixing Divisional plate for urinal 320x720mm (three hundred twenty into seven hundred twenty millimetre) vitreous china .of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and fixing 32mm (thirty two millimetre) dia C.P. bottle trap for wash basin or sink of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and fixing vitreous China pedestal for wash basin or sink of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and fixing C.P. brass towel rail complete with C.P. brass brackets fixed to wooden plugs with C.P. brass screws :- 600mmx 20mm (six hundred millimetre into twenty millimetre) including carriage of materials with in all leads , lifts and other incidentals.

Providing and fixing chromium plated brass soap dish with C.P. brass brackets fixed to wooden cleats with C.P. brass screws including carriage of materials with in all leads , lifts and other incidentals.

Providing and Fixing Toilet Paper holder of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and Fixing Towel rack of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and fixing 600x450 mm (six hundred into four hundred fifty millimetre) beveled edge mirror of superior glass (of approved quality) complete with 6 mm (six millimetre) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and Fixing 600mmx120mm (six hundred millimetre into one hundred twenty millimetre) glass shelf with CP brass bracket and guard rail complete of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and Fixing 15mm (fifteen millimetre) dia CP brass bib tap of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and Fixing 15mm (fifteen millimetre) dia CP brass angle valve of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and Fixing Consealed stop cock heavy duty 15mm (fifteen millimetre) dia of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and Fixing divertor for bath and shower system with divertor assembly of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and Fixing 8mm (eight millimetre) dia CP/SS Jet with flexible tube with SS triangle plate of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and Fixing unplasticised PVC connection pipe with brass union 45cm (forty five centimetre) long with 15mm (fifteen millimetre) nominal bore of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and Fixing PVC flexible waste pipe for sink and wash basin including PVC waste fitting complete of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and Fixing one hole basin mixing faucet of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and Fixing bath tub spout with one hole basin mixing faucet of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and fixing shower head 100x 100mm (one hundred into one hundred millimetre) of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and Fixing 100 mm (one hundred millimetre) dia chromium plated gratings of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and fixing PVC Reducing Tee 150 x 100 mm (one hundred fifty into one hundred millimetre) of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and Fixing 160 mm (one hundred sixty millimetre) dia PVC (D plast) pipes of pressure 6kg/sqm (six kilogram/square metre) of approved quality as per direction of Engineer-in-charge with in all leads, lifts and other incidentals.

Providing and fixing Polyethelene-Aluminium-Polyethelene PE-AL-PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers &connectors etc., with c lamps at 1.00 (one) metre spacing. This includes testing of joints complete as per direction of the Engineer in charge.

1216 (one thousand two hundred sixteen) 16mm (sixteen millimetre) OD Pipe

Providing and fixing Polyethelene-Aluminium-Polyethelene PE-AL-PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers &connectors etc., with c lamps at 1.00 (one) metre spacing. This includes testing of joints complete as per direction of the Engineer in charge. 1620 (one thousand six hundred twenty) 20mm OD Pipe (twenty millimetre OD pipe) with in all leads, lifts and carriage of materials and other incidentals.

Providing and fixing Polyethelene-Aluminium-Polyethelene PE-AL-PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers &connectors etc., with c lamps at 1.00 (one) metre spacing. This includes testing of joints complete as per direction of the Engineer in charge. 3240 (three thousand two hundred forty) 40mm (forty millimetre) OD Pipe with in all leads, lifts and carriage of materials and other incidentals.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipe ISI marked including jointing with approved adhesive etcetera including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

75mm (seventy five millimetre) dia

110 mm (one hundred ten millimetre) dia

Providing and fixing 110mm x 75mm (one hundred ten into ninety) millimetre PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etcetera complete in all respect as per direction and satisfaction of Engineer-in-Charge with in all leads, lifts and carriage of materials and other incidentals.

Providing and fixing PVC single equal branch with ovel access door, ISI marked insertion rubber washer 3mm (three millimetre) thick bolts and nuts complete including fixing with approved adhesive etcetera complete in all respect including carriage of materials within all leads and lifts as per direction and satisfaction of Engineer-in-Charge.

110 mm (one hundred ten millimetre) dia

75mm (seventy five millimetre) dia

Providing and fixing PVC door bend with ovel access door, insertion rubber washer 3mm (three millimetre) thick bolts and nuts ISI marked complete including fixing with approved adhesive etcetera complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

110 mm (one hundred ten millimetre) dia

75mm (seventy five millimetre) dia

Providing and Fixing PVC Single equal branch Plain, ISI marked complete including fixing with aproved adhesive complete in all respect including carriage of materail with in all leads, lifts and as per direction of Engineer-in-charge

110 mm (one hundred ten millimetre) dia

75mm (seventy five millimetre) dia

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etcetera including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

110 mm (one hundred ten millimetre) dia

75mm (seventy five millimetre) dia

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etcetera complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

110 mm (one hundred ten millimetre) dia

75mm (seventy five millimetre) dia

Providing and fixing PVC 1000 (one thousand) litres net capacity water storage tank of ISI: 12701 marked, G.I. inlet and outlet connection, 15mm (fifteen millimetre) nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting upto all heights above ground level and including carriage of material with in all leads and lifts as per direction and satisfaction of Engineer-in-Charge.

Constructing brick masonry manhole in cement mortar 1:4 ( one cement : four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm (twenty millimetre) nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm (forty millimetre) nominal size), inside plastering 12 mm (twelve millimetre) thick with cement mortar 1:3 (1cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm (twenty millimetre) nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm (ninty into eighty centimetre) and 45 cm (forty five centimetre) deep including C.I. cover with frame (medium duty) 500 mm (five hundred millimetre) internal dimensions, total weight of cover and frame to be not less than 116 kg (one hundred sixteen kilogram) (weight of cover 58 kg (fifty eight kilogram) and weight of frame 58 kg (fifty eight kilogram)) with in all leads, lifts and carriage of materials and other incidentals.

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm (twenty millimetre) nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm (forty millimetre) nominal size), inside plastering 12 mm (twelve millimetre) thick with cement mortar 1:3 (1cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm (twenty millimetre) nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 120x90 cm and 90 cm (one hundred twenty into ninety centimetre and ninety centimetre) deep including C.I. cover with frame (medium duty) 500 mm (five hundred millimetre) internal dimensions, total weight of cover and frame to be not less than 116 kg (one hundred sixteen kilogram) (weight of cover 58 kg (fifty eight kilogram) and weight of frame 58 kg (fifty eight kilogram))

Supplying and fixing CI Cover with frame for manhole 500 mm (five hundred millimetre) dia CI cover (medium duty) man hole in slab . Weight of frame and cover not less then 116 kg (one hundred sixteen kilogram) with in all leads, lifts and carriage of materials and other incidentals.

Providing MS foot rests including fixing in man holes with 20x20x10 cm (twenty into twenty into ten centimetre) blocks 1:3:6 with 20mm (twenty millimetre) dia round bars with in all leads, lifts and carriage of materials and other incidentals.

Providing and laying , jointing and testing in trenches 150mm (one hundred fifty millimetre) dia. Centrifugally cast (span) ductile iron pipes for water, gas and sewerage with socket and spigot ends conforming to IS:8329-2000 and latest with up to date amendments in a length of 5.00 (to 6.00mtrs (five to six metre) class K7 for push on joint (rubber gasket D-jointing) including short pieces collars with cement mortar liming inside the pipes with outside zinc coating as per IS-8329-2000 with in all leads and lifts complete and to the satisfaction of the Engineer-in-charge with in all leads, lifts and carriage of materials and other incidentals. (Earth work in trenches to be measured and paid for separately) with in all leads, lifts and carriage of materials and other incidentals.

Providing Tyton (Push on Joints) to ductile iron pipes and fittings including testing of joints and cost of tyton rubber ring (SBR quality) conforming to IS-12820-1989 latest with up-to-date amendments including all leads, lifts and carriage of materials and other incidentals.

Providing and Fixing brass Wheel of dia 32mm (thirty two millimetre) of approved quality including carriage of materials within all leads ,lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and Fixing brass Wheel of dia 25mm (twenty five millimetre) of approved quality including carriage of materials within all leads, lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and Fixing brass Non return valve 40mm (forty millimetre) of approved quality including carriage of materials within all leads, lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

M/S NDN Constructions