01/ KMDA / EM / SE / MC-I / NIT / 2024-25

Amount

Supply & delivery at site , installation and commissioning of vertical turbine pump motor set complete having the following head discharge characteristics , capable to discharge raw water ,having specific gravity 1.025, with SS(CF8M) impeller, CI casing , dischagre head ,motor stool along with other standard accessories with TEFC ,750 rpm (synchronous),8 Pole, 3 Phase, 11 kv ± 10% AC ,insulation class F , IP 55 , squirrel cage induction motor of suitable ratings as required along with SS316 Caission pipe complete with adequate supports and as per technical specification and direction of EIC and as per CPHEEO standard . Motor shall have a margin of at least 30% margin over the pump input at duty point or 10% margin over the maximum pump input in the worst case of the pump operation in the total range (from shut-off to run out), whichever is higher .Pumps shall be installed on suitable RCC foundation adhering to all the technical requirements of the pump manufacturer. Make : Pump :WPIL / Mather & Platt / KBL . Motor : CGL/Marathon/Siemens/ABB

1150 m³/hr against a tentative head of 55 to 60 m (2nos working + 2 nos. standby )

(Finally actual TDH & design of caission pipe to be determined by the tenderer at the time of detailed engineering after consultation with the concerned division dealing with the pipe laying )

Supply, delivery at site, installation of 9 Panel HT Switch Board of 350 MVA, 11 KV 18.4 KA , 800 Amps complete in all respect with all other accessories as per technical specification and direction of EIC. Incomer-1no., Motor feeder-4 nos.,Capacitor feeder-2nos, Transformer feeder-2 nos . Make : Schneider/ Siemens / ABB

Supply, delivery at site & installation of 100 KVA, 11/0.433KV , ONAN outdoor transformer complete in all respect with all other accessories and proper fencing as per technical specification and direction of EIC conforming to IS :1180 Level 1 ( Latest revision : Level 1) ( 1no. Working + 1no. Standby ) Make : KEC / Schneider / CGL

Supply, delivery at site, installation of LT. P.D.B. complete in all respect with all other accessories as per technical specification ( 2 nos. incomer ACB , 1 no. bus coupler , Lighting feeders, Valve actuator feeders , EOT crane feeder, drinking water pump feeder, ventilation feeder and other auxiliary feeders as required as per site condition and as per technical specification and direction of EIC ). Make : Sellwin Electricals Pvt. Ltd. / PCE Project Pvt. ltd / System Control / ABB .

Supply, delivery at site, installation of central control desk complete in all respect with all other accessories as per technical specification and direction of EIC. Make : Sellwin Electricals Pvt. Ltd. / PCE Project Pvt. ltd / System Control / ABB

Supply, delivery at site, installation of 110Volt DC Battery Charger with 165 AH SMF VRLA battery, complete in all respect with all other accessories as per technical specification and direction of EIC.(capacity to be determined during detailed engineering) . Make : Electro Service /Dekem/ Caldyne

Supply, delivery at site , installation of 1400VA noise less digital sine wave Inverter with 180AH , 12Volt Tubular Battery for emergency lighting of the plant. Make : Exide / Amaron / Microtech

Supply,deloivery and Installation of Capacitor Bank.

Supply, delivery at site , fitting and fixing of electro-magnetic flow meter of following sizes , comprising of flow sensor and transmitter, signal conditioner if required, flow indicator, flow totaliser(controller unit ) and all other accessories complete as per specification and direction of EIC.

Supply, delivery at site fitting and fixing of following MS pipe including fabrication of all necessary accessories special viz dismantling joints, Puddle plates ( 20mm), Bell Mouth, bends, tees, enlarger/reducer, R.C.C. pedestal for common manifold , etc including cutting walls, pipes, making flanged & welded joints as required, fitting fixing complete in all respect including cost of all fitings, sundry and jointing materials as required for laying of pipe with anti-corrosive treatment of all pipe surface complete as per technical specification and direction of EIC.

400 mm., 10mm thick (For individual delivery piping)

400 mm , 10mm thick DF Metallic dismantling joint with split flange, long stud, bolts, nuts etc.

600 mm , 10mm thick (For common manifold piping)

600 mm , 10mm thick (For flowmeter piping)

Supply, delivery at site, lowering, fitting and fixing of DIDF non return valve (PN-1.6 ) of following size in proper position and alignment by providing temporary support as required including cost of all sundry materials such as gaskets, nuts, bolts etc. all complete as required to complete the job in all respect as per technical specification and direction of EIC.

400 mm, dia (for individual pump delivery side)

Supply, delivery at site, lowering, fitting and fixing of DIDF butterfly valve (PN-1.6) alongwith suitable rated motorised actuator of following size in proper position and alignment by providing temporaray support as required including cost of all sundry materials such as gaskets, nuts, bolts etc all complete as required to complete the job in all respect as per technical specification and direction of EIC.

400 mm dia (for individual pump delivery line)

600 mm dia (for common header )

Supply, delivery at site, fitting and fixing of gun metal gate/globe / check valve for drinking water lines including 1 HP submersible pump ,starter panel , etc complete with all accessories including cost of all sundry materials and fitting fixing charges as required as per technical specification and direction of EIC.

50mm dia Gate / Globe Valve

32mm dia Gate / Globe Valve

50mm dia Check Valve

Supply, delivery at site, fitting and fixing of single orifice type air release valve with isolation valve of adequate size for manifold pipe line complete with all other standard accessories including cost of all sundry materials and fitting fixing charges as required as per technical specification and direction of EIC.

Supply, delivery at site, fitting and fixing of dust & damp proof following field instruments complete with all valves, cocks and other fixtures including cost of all sundry materials as required as per technical specification and direction of EIC.

0-10 kgf/cm² (6" dial bourdon type for individual delivery line,accuracy ± 1%)

0-10 kgf/cm² (8" dial bourdon type for common delivery manifold,accuracy ± 1%)

Pressure transmitter including cabling (For individual delivery line )

Pressure transmitter including cabling (For common delivery manifold )

Supply, delivery at site fitting and fixing of the ultra sonic water level sensor with indicator including transmitter / transducer / stilling pipe and all other accessories including all cabling connections all complete as per specification and direction of EIC.

Supply, delivery at site fitting and fixing of float type mechanical level indicator and staff including all other accessories as per specification and direction of EIC.

Supply , delivery ,fitting & fixing of pressure gauges as per direction of EIC

Supply , delivery ,fitting & fixing of pressure Transmitters as per direction of EIC

Supply ,delivery at site and laying of 11 KV grade XLPE insulated, PVC outer sheathed, armoured, aluminium conductor cable of following size either through cable duct or through cable trays or through protection pipes as per technical specification and direction of EIC.

3 core x 300 mm² ( CESC room to KMDA HT Panel ) .

Supply, delivery at site and laying of 11 KV grade XLPE insulated, PVC outer sheathed, armoured, aluminium conductor cable of following size either through cable duct or through cable trays or burried underground through brick protection or through protection pipes as per technical specification and direction of EIC.

3 core x As required mm² from HT panel to transformer

3 core x As required mm² HT motor feeder to motor terminal

3 core x As required mm² HT capacitor feeder to capacitor bank

Supply, delivery at site and laying of 1.1KV grade XLPE insulated, PVC outer sheathed, armoured/unarmoured , stranded aluminium /copper conductor for auxiliary power , control cable and signal cable of required size either through cable duct or through cable trays or through protection pipes as per technical specification and direction of EIC.

Making end termination of 11KV grade 3 core x 300 mm² XLPE and other HT cables, insulated, PVC outer sheathed, armoured, aluminium conductor cable with push on type premoulded cable jointing kit indoor/ outdoor type as required complete with gland and other hardwares as per direction of EIC.

Making end termination of 1.1KV grade XLPE/PVC insulated armoured Al./Cu. conductor cable with gland and other hardwares as required as per direction of EIC

Supply, delivery, fitting and fixing sheet steel fabricated double door type 4+ 4 way TPN MCB distribution board with 1 no 63A 4 pole isolator and 12 nos 6 — 32 Amps. SPMCB on wall as per direction of the EIC.

Supply, delivery at site, installation of control panel,sheet steel fabricated complete in all respect with all accessories for control of exhaust fans and other emergency loads as per technical specification and direction of EIC.

Distribution wiring with 1.1KV grade 2 X 1.5 mm² PVC insulated unsheathed single core stranded copper wire in 20mm G.I. conduit to light, fan, call bell point with 10A DP toggle switch fixed on 3mm thick bakelite cover in double door sheet metal switch board with magetic locking arrangement as per direction of the EIC.

Distribution wiring with 1.1KV grade 2 X 2.5 mm² PVC insulated unsheathed single core stranded copper wire in 20mm G.I. conduit to 250 V 15 A 6 pin composite plug socket fixed on 3mm thick bakelite cover in double door sheet metal switch board with magetic locking arrangement including 1 X 1 mm² PVC insulated unsheathed single core stranded copper wire as earth continuity wire.

Wiring with 1.1KV grade 3 X 1.5 mm² PVC insulated unsheathed single core stranded copper wire in 20mm G.I. conduit including 1 X 1 mm² PVC insulated unsheathed single core stranded copper wire as earth continuity wire from starter control panel to exhaust fan point.

Supply and fixing of Industrial type LED Tube Light fitting of make Philips , model (EnduraLED) BN308LC LED40S-6500 L120 PSU WH, completely wired up with necessary accessories , as required to maintain lux level as per IEC & as per specification & direction of EIC.

Supply and fixing street lights of make Philips , model- BRP410 LED 110 CW HE MR FG S2 PSU GR LED fitting completely wired up with necessary accessories including fixing on pole as required to maintain lux level as per IEC &as per specification & direction of EIC.

Supply and fixing of 70 W SON post top luminaries or equivalent LED fitting completely wired up with necessary ignitor, ballast, capacitor and lamp etc including S & F of G.I. pipe bracket on wall as required to maintain lux level as per IEC & as per specification & direction of EIC.

Supply and fixing of highbay luminaries of make Philips , model- Durabay Prime BY225P LED100S CW WB PSU FG GR V1 , LED fitting completely wired up with necessary accessories , including S&F of M.S. clamp on ceiling as required as per to maintain lux level as per IEC & specification & direction of EIC.

Supply and fixing of 300mm Sweep, 230 V, 1Ph, 50 Hz, 4 pole exhaust fan including S & F of M.S. cowl and making suitable hole in the wall including mending good damages complete as per specification & direction of EIC.

Supply and fixing of 600mm Sweep, 415 V, 3Ph, 50 Hz, 6 pole exhaust fan including S & F of M.S. cowl and making suitable hole in the wall including mending good damages complete as per specification & direction of EIC.

Supply and fixing of 1200mm Sweep, 230 V, 1Ph, 50 Hz, ceiling fan including S & F of electronoc regulator as per specification & direction of EIC.

Supply and fixing of 450mm Sweep, 230 V, 1Ph, 50 Hz, 4 pole pedestal type air circulator as per specification & direction of EIC.

Fabrication and installation of structural steel works such as, cable duct cover by chequered plates, pipe & valve supports, valve operating platform, walkway ,cable supports, trays, hangers as required as per specification & direction of EIC.

Supply and fixing of 600mm Sweep, 230 V, 1Ph, 50 Hz, 4 pole wall bracket type air circulator as per specification & direction of EIC.

Supply, delivery and erection of 9.0 mtr long G.I. Pole fabricated from M.S. sheet incl. earthing of individual & light fittings as per design and direction of EIC.

Supply and fixing of G.I. Bracket Arms suitable for theG.I. Pole with necessary pole cap,hardwares etc as required as per design and direction of EIC.

Twin Arm upto 2M long

Single Arm upto 2M long

Supply, delivery, fitting,fixing of fire extinguishers complete in all respect i.e. with first charge of refill, mounting bracket etc. as per technical specification and direction of EIC.

Portable type fire extinguisher (2 Kg Capacity)

5Kg. Capacity (ABC Type)

Supply and fixing on wall or on stand of 9 Ltrs capacity M.S. bucket, 50% of the bucket capacity to be filled with sand as per direction of EIC.

Earthing the whole installation as per IE Rules & Acts, specifications, complete in all respect including supply,installation of all required earthing materials,flats,earth electrodes and all other sundries,fitting,fixtures including making proper earth stations as per technical specification and direction of EIC.

Providing fencing with structural gates around the periphery of the transformer yard as per I.E. rules including supply and fixing of necessary M.S. angles, flates G.I. mesh etc. as required to complete the job as per specification and direction of EIC.

Supply and fixing of E.I. Danger board on wall & fencing as per direction of EIC

Supply and providing 11KV grade rubber mat as per direction of EIC.

Supply and fixing on wall a shock treatment chart duly framed by polished wood and the glass fitted in front complete as per direction of EIC.

Display of back lit & non lit sign board of various sizes on the pump house wall fascia or elsewhere as per direction of EIC.

Supply ,installation & commissioning, of 5 MT double girder capacity EOT crane complete in all respect including testing as per technical specification and direction of EIC.

Painting the whole installation as per technical specifcation and direction of EIC.

Carrying out high pressure test of the HT installation by approved agency and obtaining necessary clearance fron Directorate of Electricity as per direction of EIC.

Supply of drawings for approval and finally as-built drawings in 6sets and CDs .

Supply, delivery at site & laying of MS pipe including fabrication of all necessary accessories special ,enlarger, ,R.C.C. / fabricated pedestal , thrust blocks , etc including cutting pipes, making flanged & welded joints as required, for joining the common delivery manifolds with the existing prelaid rising main pipes complete as per technical specification and direction of EIC. Note : Any mechanical or electrical or civil , parts/spare/equipment not included in the BOQ but required to complete the project is to be supplied by the agency at free of cost i.e.cost of such items shall be included within this offer.

Operation and maintenance of the entire CWPS incl. supply of consumables for a period of five years along with deputation of trained staffs as required to run the pumping station .

1 st year

2 nd year

3 rd year

4 th year

5 th year

Traders and Engineers Private Limited (BID ID -5833551)

POWER INDIA (BID ID -5812583)

MACHINE SUPPLIERS SYNDICATE PVT LTD (BID ID -5809460)