MS-VM Section- Construction of new TRD depot at ACK (Acharapakkam).

provision of 12%. However, tenderers should quote rates for items inclusive of 18% GST).

Item- 1 SW.I -Construction of new TRD depot at ACK (Acharapakkam)

S No. Item No Description of Item Unit Qty Rate Amount

2.0 EARTH WORK

CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY

Earth work in excavation by mechanical means

(Hydraulic excavator) / manual means in

foundation trenches or drains (not exceeding

1.5 m in width or 10 sqm on plan), including

2.8 dressing of sides and ramming of bottoms, lift

upto 1.5 m, including getting out the

excavated soil and disposal of surplus

excavated soil as directed, within a lead of 50

2.25 Filling available excavated earth (excluding cum 750 253.95 190462.5

rock) in trenches, plinth, sides of foundations

etc. in layers not exceeding 20cm in depth,

consolidating each deposited layer by

ramming and watering, lead up to 50 m and lift

Extra for every additional lift of 1.5 m or part

2.26 thereof in excavation / banking excavated or

stacked materials.

2.31 Clearing jungle including uprooting of rank Sqm 800 14.5 11600

vegetation, grass, brush wood, trees and

saplings of girth up to 30 cm measured at a

height of 1 m above ground level and removal

of rubbish up to a distance of 50 m outside the

periphery of the area cleared.

4.0 CONCRETE WORK

4.1S CEMENT CONCRETE (CAST IN SITU)

Providing and laying in position cement

concrete of specified grade excluding the cost

of centering and shuttering - All work up to

derived from natural sources : 6 graded stone

aggregate 20 mm nominal size derived from

natural sources)

Centering and shuttering including strutting,

propping etc. and removal of form work for :

6 4.3.1 Foundations, footings, bases for columns Sqm 50 307.95 15397.5

5.0 REINFORCED CEMENT CONCRETE

5.1S CAST IN SITU

Providing and laying in position specified grade

of reinforced cement concrete, excluding the

cost of centering, shuttering, finishing and

reinforcement - All work up to plinth level :

derived from natural sources: 3 graded stone

aggregate 20 mm nominal size derived from

natural sources)

Reinforced cement concrete work in walls (any

thickness), including attached pilasters,

buttresses, plinth and string courses, fillets,

5.2 columns, pillars, piers, abutments, posts and

struts etc. above plinth level up to floor five

level, excluding cost of centering, shuttering,

finishing and reinforcement :

derived from natural sources : 3 graded stone

aggregate 20 mm nominal size derived from

natural sources)

5.9S FORM WORK

Centering and shuttering including strutting,

propping etc. and removal of form for

5.9.1 Foundations, footings, bases of columns, etc. Sqm 130 307.95 40033.5

for mass concrete

CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY

5.9.3 Suspended floors, roofs, landings, balconies Sqm 630 766.55 482926.5

and access platform

5.9.5 Lintels, beams, plinth beams, girders, Sqm 50 608.35 30417.5

bressumers and cantilevers

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Sqm 230 804.25 184977.5

6.0 MASONRY WORK

6.12S HALF BRICK MASONRY

Half brick masonry with common burnt clay

F.P.S. (non modular) bricks of class designation

7.5 in superstructure above plinth level up to

6.26S EXPOSED BRICK WALL

Brick work with common burnt clay modular

bricks of class designation 7.5 in exposed brick

6.27 work including making horizontal and vertical

grooves 10mm wide 12 mm deep complete in

cement mortar 1:6 (1 cement : 6 coarse sand).

14 6.27.1 From ground level upto plinth level cum 80 5588.65 447092

15 6.27.2 Above plinth level upto floor V level cum 340 7218.75 2454375

8.0 CLADDING WORK

8.20S STONE WORK DRY CLADDING

8.31 Providing and fixing Ist quality ceramic glazed Sqm 15 1063.45 15951.75

wall tiles conforming to IS: 15622 (thickness to

be specified by the manufacturer), of approved

make, in all colours, shades except burgundy,

bottle green, black of any size as approved by

16 Engineer-in-Charge, in skirting, risers of steps

and dados, over 12 mm thick bed of cement

mortar 1:3 (1 cement : 3 coarse sand) and

jointing with grey cement slurry @ 3.3kg per

sqm, including pointing in white cement mixed

with pigment of matching shade complete.

9.0 WOOD AND P.V.C. WORK

9.1S FRAMES AND TRUSSES

Providing wood work in frames of doors,

windows, clerestory windows and other

frames, wrought framed and fixed in position

with hold fast lugs or with dash fasteners of

required dia & length (hold fast lugs or dash

fastener shall be paid for separately).

Providing and fixing glazed shutters for doors,

windows and clerestory windows using 4 mm

thick float glass panes, (weight not less than

10 kg per sqm) fixing with ISI marked M.S.

pressed butt hinges bright finished of required

size with necessary screws.

Providing and fixing factory made laminated

veneer lumber glazed shutter conforming to IS:

14616 and TADS 15:2001 (Part B), using 4 mm

thick float glass panes for doors, windows and

9.10 clerestory windows, fixing with butt hinges of

required size with necessary screws, all as per

directions of Engineer-in-charge. (Note:- Butt

hinges and necessary screws shall be paid

Providing and fixing 25 mm thick shutters for

cup board etc. :

CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY

Providing and fixing ISI marked flush door

shutters conforming to IS : 2202 (Part I) non-

decorative type, core of block board

9.21 construction with frame of 1st class hard wood

and well matched commercial 3 ply veneering

with vertical grains or cross bands and face

veneers on both faces of shutters:

9.21.1 35 mm thick including ISI marked Stainless Sqm 15 2015.75 30236.25

Steel butt hinges with necessary screws

9.23 Extra for providing lipping with 2nd class teak Sqm 9 401.4 3612.6

wood battens 25 mm minimum depth on all

edges of flush door shutters (over all area of

door shutter to be measured).

9.40S MISCELLANEOUS-WOOD WORK

9.53 Providing 40x5 mm flat iron hold fast 400 mm Each 81 194.35 15742.35

long including fixing to frame with 10 mm

diameter bolts, nuts and wooden plugs and

21 embedding in cement concrete block

300x100x150 mm 1:3:6 mix (1 cement : 3

coarse sand : 6 graded stone aggregate 20mm

9.72S BRASS FITTINGS

Providing and fixing bright finished brass tower

9.74 bolts (barrel type) with necessary screws etc.

Providing and fixing bright finished brass door

latch with necessary screws etc. complete :

Providing and fixing bright finished brass

handles with screws etc. complete:

9.82 Providing and fixing bright finished brass Each 11 109.6 1205.6

26 hanging type floor door stopper with necessary

screws, etc. complete.

9.83 Providing and fixing aluminium die cast body Each 6 1025.65 6153.9

tubular type universal hydraulic door closer

(having brand logo with ISI, IS : 3564,

embossed on the body, door weight upto 35 kg

and door width upto 700 mm), with necessary

accessories and screws etc. complete.

9.105S GYPSUM BOARD PARTITIONS

9.119 Providing and fixing factory made P.V.C. door Metre 20 408.25 8165

frame of size 50x47 mm with awall thickness

of 5 mm, made out of extruded 5mm rigid PVC

foam sheet, mitred at corners and joined with

2 Nos of 150 mm long brackets of 15x15 mm

M.S. square tube, the vertical door frame

28 profiles to be reinforced with 19x19 mm M.S.

square tube of 19 gauge, EPDM rubber gasket

weather seal to be provided through out the

frame. The door frame to be fixed to the wall

using M.S. screws of 65/100 mm size,

complete as per manufacturer's specification

and direction of Engineer- in-Charge.

CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY

Providing and fixing factory made panel PVC

door shutter consisting of frame made out of

M.S. tubes of 19 gauge thickness and size of

19 mm x 19 mm for styles and 15x15 mm for

top & bottom rails. M.S. frame shall have a

coat of steel primers of approved make and

manufacture. M.S. frame covered with 5 mm

thick heat moulded PVC 'C' channel of size 30

mm thickness, 70 mm width out of which 50

mm shall be flat and 20 mm shall be tapered in

45 degree angle on both side forming styles

and 5 mm thick, 95 mm wide PVC sheet out of

which 75mm shall be flat and 20 mm shall be

tapered in 45 degree on the inner side to form

top and bottom rail and 115 mm wide PVC

sheet out of which 75 mm shall be flat and 20

mm shall be tapered on both sides to form lock

rail. Top, bottom and lock rails shall be

provided both side of the panel. 10 mm (5 mm

x 2 ) thick, 20 mm wide cross PVC sheet be

provided as gap insert for top rail & bottom

rail, paneling of 5 mm thick both side PVC

sheet to be fitted in the M.S. frame welded/

sealed to the styles & rails with 7 mm (5

mm+2 mm) thick x 15 mm wide PVC sheet

beading on inner side, and joined together

with solvent cement adhesive. An additional 5

mm thick PVC strip of 20 mm width is to be

stuck on the interior side of the 'C' Channel

using PVC solvent adhesive etc. complete as

per direction of Engineer-in-charge,

manufacturer's specification & drawing.

Providing and fixing wire gauge shutters using

stainless steel grade 304 wire gauge with wire

of dia 0.5 mm and average width of aperture

1.4 mm in both directions for doors, windows

and clerestory windows with necessary screws

Providing and fixing factory made uPVC white

colour fixed glazed windows/ventilators

comprising of uPVC multi-chambered frame

and mullion (where ever required) extruded

profiles duly reinforced with 1.60 +/- 0.2 mm

thick galvanized mild steel section made from

roll forming process of required length (shape

& size according to uPVC profile), , uPVC

e x t r u d e d glazing beads of appropriate

dimension, EPDM gasket, G.I fasteners 100 x 8

mm size for fixing frame to finished wall,

plastic packers, plastic caps and necessary

stainless steel screws etc. Profile of frame shall

9.147B be mitred cut and fusion welded at all corners,

mullion (if required) shall be also fusion

welded including drilling of holes for fixing

hardware's and drainage of water etc. After

fixing frame the gap between frame and

adjacent finished wall shall be filled with

weather proof silicon sealant over backer rod

of required size and of approved quality, all

complete as per approved drawing & direction

of Engineer-in-Charge. (Single / double glass

panes and silicon sealant shall be paid

separately). Variation in profile dimension in

higher side shall be accepted but no extra

payment on this account shall be made.

CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY

9.147B.1 Fixed window / ventilator made of (small Sqm 25 7249.9 181247.5

series) frame 47 x 50 mm & mullion 47 x 68

30 mm both having wall thickness of 1.9 +/- 0.2

mm and single glazing bead of appropriate

dimension. (Area upto 0.75 sqm.)

10.0 STEEL WORK

10.1 Structural steel work in single section, fixed Kg 6000 93.05 558300

with or without connecting plate, including

31 cutting, hoisting, fixing in position and

applying a priming coat of approved steel

primer all complete.

10.2 Structural steel work riveted, bolted or welded Kg 1500 111.95 167925

in built up sections, trusses and framed work,

32 including cutting, hoisting, fixing in position

and applying a priming coat of approved steel

primer all complete.

Supplying and fixing rolling shutters of

approved make, made of required size M.S.

laths, interlocked together through their entire

length and jointed together at the end by end

locks, mounted on specially designed pipe

shaft with brackets, side guides and

arrangements for inside and outside locking

with push and pull operation complete,

including the cost of providing and fixing

necessary 27.5 cm long wire springs

manufactured from high tensile steel wire of

adequate strength conforming to IS: 4454 -

part 1 and M.S. top cover of required thickness

for rolling shutters.

10.7 Providing and fixing ball bearing for rolling Each 10 424.2 4242

11.0 FLOORING

11.4 52 mm thick cement concrete flooring with Sqm 150 855.9 128385

concrete hardener topping, under layer 40 mm

thick cement concrete 1:2:4 (1 cement : 2

coarse sand : 4 graded stone aggregate 20

mm nominal size) and top layer 12 mm thick

cement hardener consisting of mix 1:2 (1

35 cement hardener mix : 2 graded stone

aggregate 6 mm nominal size) by volume,

hardening compound mixed @ 2 litre per 50 kg

of cement or as per manufacturer's

specifications. This includes cost of cement

slurry, but excluding the cost of nosing of steps

11.37S CERAMIC GLAZED TILES

11.39 Providing and laying rectified Glazed Ceramic Sqm 50 1142.8 57140

floor tiles of size 300x300 mm or more

(thickness to be specified by the

manufacturer), of 1st quality conforming to IS :

15622, of approved make, in colours White,

36 Ivory, Grey, Fume Red Brown, laid on 20 mm

thick cement mortar 1:4 (1 Cement: 4 Coarse

sand), jointing with grey cement slurry @ 3.3

kg/ sqm including grouting the joints with

white cement and matching pigments etc.,

11.41S VITRIFIED FLOOR TILES

CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY

Providing and laying vitrified floor tiles in

different sizes (thickness to be specified by the

manufacturer) with water absorption less than

0.08% and conforming to IS: 15622, of

approved make, in all colours and shades, laid

on 20mm thick cement mortar 1:4 (1 cement :

4 coarse sand), jointing with grey cement

slurry @ 3.3 kg/ sqm including grouting the

joints with white cement and matching

pigments etc., complete.

12.0 ROOFING

Providing, fixing and embedding sand cast iron

accessories for rain water pipes in the masonry

12.40 surrounded with 12 mm thick cement mortar of

the same mix, as that of masonry (lead

caulking will be paid for separately):

Providing and fixing on wall face unplasticised

Rigid PVC rain water pipes conforming to IS :

12.41 13592 Type A, including jointing with seal ring

conforming to IS : 5382, leaving 10 mm gap for

thermal expansion, (i) Single socketed pipes.

Providing and fixing on wall face unplasticised -

PVC moulded fittings/ accessories for

unplasticised Rigid PVC rain water pipes

conforming to IS : 13592 Type A, including

jointing with seal ring conforming to IS : 5382,

leaving 10 mm gap for thermal expansion.

12.42.5 Bend 87.5 degrees

12.42.6 Shoe (Plain)

Providing and fixing unplasticised -PVC pipe

clips of approved design to unplasticised - PVC

rain water pipes by means of 50x50x50 mm

hard wood plugs, screwed with M.S. screws of

required length, including cutting brick work

and fixing in cement mortar 1:4 (1 cement : 4

coarse sand) and making good the wall etc.

12.50 Providing and fixing precoated galvanised iron Sqm 120 671.55 80586

profile sheets (size, shape and pitch of

corrugation as approved by Engineer-in-

charge) 0.50 mm (+ 0.05 %) total coated

thickness with zinc coating 120 grams per sqm

as per IS: 277, in 240 mpa steel grade, 5-7

microns epoxy primer on both side of the sheet

and polyester top coat 15-18 microns. Sheet

should have protective guard film of 25

42 microns minimum to avoid scratches during

transportation and should be supplied in single

length upto 12 metre or as desired by

Engineer-in-charge. The sheet shall be fixed

using self drilling /self tapping screws of size

(5.5x 55 mm) with EPDM seal, complete upto

any pitch in horizontal/ vertical or curved

surfaces, excluding the cost of purlins, rafters

and trusses and including cutting to size and

shape wherever required.

CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY

Providing and fixing precoated galvanised steel

sheet roofing accessories 0.50 mm (+0.05 %)

total coated thickness, Zinc coating 120 grams

per sqm as per IS: 277, in 240 mpa steel

grade, 5-7 microns epoxy primer on both side

of the sheet and polyester top coat 15-18

microns using self drilling/ self tapping screws

13.0 FINISHING

13.1S CEMENT PLASTER (IN FINE SAND)

13.1 12 mm cement plaster of mix :

13.11S CEMENT PLASTER IN TWO COATS

13.11 18 mm cement plaster in two coats under Sqm 2280 442.75 1009470

layer 12 mm thick cement plaster 1:5 (1

45 cement : 5 coarse sand) finished with a top

layer 6 mm thick cement plaster 1:6 (1 cement

: 6 fine sand).

13.16S 6MM CEMENT PLASTER

13.16 6 mm cement plaster of mix :

13.44S EXTERIOR FINISHING

Finishing walls with 100% Premium acrylic

emulsion paint having VOC less than 50

gm/litre and UV resistance as per IS

15489:2004, Alkali & fungal resistance, dirt

resistance exterior paint of required shade

(Company Depot Tinted) with silicon additives.

13.48A.1 New work (Two or more coats applied @ 1.43 Sqm 3280 154.45 506596

47 litre/ 10 sqm. Over and including priming coat

of exterior primer applied @ 0.90 litre/10 sqm.

Painting with synthetic enamel paint of

13.62 approved brand and manufacture of required

colour to give an even shade :

13.62.1 Two or more coats on new work over an under Sqm 50 191.4 9570

48 coat of suitable shade with ordinary paint of

approved brand and manufacture

Lettering with black Japan paint of approved letter

brand and manufacture per cm

17.0 SANITARY INSTALLATIONS

Providing and fixing water closet squatting pan

(Indian type W.C. pan ) with 100 mm sand cast

Iron P or S trap, 10 litre low level white P.V.C.

flushing cistern, including flush pipe, with

17.1 manually controlled device (handle lever)

conforming to IS : 7231, with all fittings and

fixtures complete, including cutting and

making good the walls and floors wherever

17.1.1 White Vitreous china Orissa pattern W.C. pan Each 4 5781.35 23125.4

50 of size 580x440 mm with integral type foot

Providing and fixing white vitreous china

pedestal type water closet (European type)

with seat and lid, 10 litre low level white

vitreous china flushing cistern & C.P. flush

bend with fittings & C.I. brackets, 40 mm flush

17.3 bend, overflow arrangement with specials of

standard make and mosquito proof coupling of

approved municipal design complete, including

painting of fittings and brackets, cutting and

making good the walls and floors wherever

CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY

17.3.1 W.C. pan with ISI marked white solid plastic Each 4 6941.3 27765.2

Providing and fixing wash basin with C.I.

brackets, 15 mm C.P. brass pillar taps, 32 mm

17.7 C.P. brass waste of standard pattern, including

painting of fittings and brackets, cutting and

making good the walls wherever require:

17.7.3 White Vitreous China Wash basin size 550x400 Each 2 2040.85 4081.7

mm with a pair of 15 mm C.P. brass pillar taps

17.72 Providing and fixing PTMT towel ring Each 4 204.7 818.8

trapezoidal shape 215 mm long, 200 mm wide

with minimum distances of 37 mm from wall

face with concealed fittings arrangement of

approved quality and colour, weighing not less

Providing and fixing PTMT towel rail complete

with brackets fixed to wooden cleats with CP

brass screws with concealed fittings

arrangement of approved quality and colour.

17.73.2 600 mm long towel rail with total length of 645 Each 4 600.35 2401.4

54 mm, width 78 mm and effective height of 88

mm, weighing not less than 190 gms.

18.0 WATER SUPPLY

18.7S C.P.V.C. PIPES

Providing and fixing Chlorinated Polyvinyl

Chloride (CPVC) pipes, having thermal stability

for hot & cold water supply, including all CPVC

plain & brass threaded fittings, i/c fixing the

pipe with clamps at 1.00 m spacing. This

includes jointing of pipes & fittings with one

step CPVC solvent cement and the cost of

cutting chases and making good the same

including testing of joints complete as per

direction of Engineer in Charge, Concealed

work, including cutting chases and making

good the wall etc.

Providing and fixing Chlorinated Polyvinyl

Chloride (CPVC) pipes, having thermal stability

for hot & cold water supply including all CPVC

plain & brass threaded fittings This includes

jointing of pipes & fittings with one step CPVC

solvent cement, trenching, refilling & testing of

joints complete as per direction of Engineer in

Charge.-External work

Providing and fixing uplasticised PVC

connection pipe with brass unions :

Providing and fixing C.P. brass shower rose

with 15 or 20 mm inlet :

C.I. SLUICE VALVES/ FIRE HYDRANTS &

18.48 Providing and placing on terrace (at all floor Litre 4000 9.7 38800

levels) polyethylene water storage tank, IS :

12701 marked, with cover and suitable locking

arrangement and making necessary holes for

inlet, outlet and overflow pipes but without

fittings and the base support for tank.

18.49S C.P. BRASS FITTINGS

Providing and fixing C.P. brass long body bib

18.51 cock of approved quality conforming to IS

standards and weighing not less than 690 gms.

CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY

Providing and fixing C.P. brass angle valve for

18.53 basin mixer and geyser points of approved

quality conforming to IS:8931

Providing and fixing PTMT grating of approved

quality and colour.

18.58.1 Circular type

19.0 DRAINAGE

19.1S STONE WARE PIPES AND FITTINGS

Providing, laying and jointing glazed

stoneware pipes class SP-1 with stiff mixture of

19.1 cement mortar in the proportion of 1:1 (1

cement : 1 fine sand) including testing of joints

etc. complete :

Constructing brick masonry manhole in cement

mortar 1:4 ( 1 cement : 4 coarse sand ) with

R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5

coarse sand (zone-III) : 3 graded stone

aggregate 20 mm nominal size), foundation

concrete 1:4:8 mix (1 cement : 4 coarse sand

(Zone-III) : 8 graded stone aggregate 40 mm

19.7 nominal size), inside plastering 12 mm thick

with cement mortar 1:3 (1 cement : 3 coarse

sand) finished with floating coat of neat

cement and making channels in cement

concrete 1:2:4 (1 cement : 2 coarse sand : 4

graded stone aggregate 20 mm nominal size)

finished with a floating coat of neat cement

complete as per standard design :

Inside size 90x80 cm and 45 cm deep

including C.I. cover with frame (light duty)

455x610 mm internal dimensions, total weight

of cover and frame to be not less than 38 kg

(weight of cover 23 kg and weight of frame 15

19.7.1.1 With common burnt clay F.P.S. (non modular) Each 9 11687.1 105183.9

bricks of class designation 7.5