Interior and Fit-out works of Oil (India) Limited, Tower-K, 4th, 5th and 6th Floor, at World Trade Centre, Nauroji Nagar, New Delhi-110029

Grand Total (DSR+NDSR) 51,49,58,992.87

Estimated Cost put in the Tender including GST

Digitally signed by

PRADYUMNA MUKHERJEE

SCHEDULE OF QUANTITIES - CIVIL WORKS

S NO DSR/MR DESCRIPTION QUANTITY UNIT RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

1 FLOORING WORKS

CEMENT CONCRETE: Providing and laying in position CEMENT CONCRETE of specified grade exluding the cost of centring and shuttering-all work upto plinth

4.1.8 1: 4: 8 (1 Cement: 4 coarse sand: 8 graded stone aggregate 40mm nominal size) 300.00 CUM 6812.00 20,43,600.00

RAISED FALSE FLOOR: Providing and fixing removable raised/false access flooring with systemand its components of approved make for different plenum

height with possible height adjustment upto 50mm, comprising of modular loadbearing floor panels supported on G.I. rectangular stinger frame workand G.I.

Pedestal etc. all complete, as per the architectural drawings, as specified and as directed by Engineer-in-charge consisting of:

(a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness minimum 2 mm and 25 mm outer diameter, fully welded

on to the G.I. Base plate of size 100mm x 100mm x 3mm at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5 mm welded with GI

fully threaded stud 16mm outer diameter with two GI Check nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head

in position at the required level. The pedestals shall be fixed to the subfloor (base) through base plate using epoxy based adhesive of approved make or the

machine screw with rawl plug.

(b) Stringers system in all steel construction hot dipped galvanized ofrectangular size 570x20x30x0.80mm thick having holes at both ends for securing the

stringers on to the pedestal head using fully threaded screws ensuring maximum lateral stability in all directions, the grid formed by the pedestal and stringer

assembly shall receive the floor panel, this system shall provide adequate solid, rigid support for access floor panel, the system shall provide a minimum clear

11.54 uninterrupted clearance between the bottom of the floor for electrical conduits and wiring etc. all complete as per the architectural drawings, as specified and as

1.02 directed by the Engineer-in-charge.

(c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high pressure Lamination of 800H grade (FS800H). Access

Floor panel shall be steel welded construction with an enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel

Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together (minimum 64 welds in each dome and 20 welds along each flange). The panel should be

Corroresist epoxy coated for lifetime rust protection and cavity formed by the top and bottom plate is filled with Pyrogrip noncombustible Portland cementitious

core mixed with lightweight foaming compound. The access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp technology upto

1mm thickness for superior adhesion and Surface flatness within 0.75mm.The panel is to withstand a Concentrated Load of 363 kgs applied on area 25mm x

25mm without collapse in the centre of the panel which is placed on four steel blocks. The panel will withstand and Uniformly Distributed Load (UDL) minimum

1250 kg/sqm and an impact load of 50kg all complete as per the approved manufacturers specification and as per the direction of Engineer-in-charge. All

specification must be printed on the side of the panel to ensure the quality of the product.

11.54.2 450mm Finished Floor Height (FFH). 70.50 sq m 5977.35 4,21,403.18

ALUMINIUM SKIRTING: Supply of 100mm Aluminium (Grade 6063) Skirting with 15 micron anodising In Natural Finish. Thickness 1.30 to 1.50mm. Designed

to conceal screws. Seamless finish. Complete with Rubber/ PVC Jointers and Gasket.

ENGINEERED WOODEN FLOORING: Supplying and Installation of engineered wooden flooring of total thickness 13 mm -16 mm, Toplayer PEFC controlled

1.04 MR Core board PEFC controlled Backing layer PEFC controlled sources Wood Veneer 2 mm Tongue and groove Length Uniclic Width Uniclic Multifit Domestic use 1000.00 sq m 6168.00 61,68,000.00

Conditions as per direction of engineer in charge.

VITRIFIED TILES: Providing and laying vitrified floor and wall tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less

than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand),

1.05 11.41A jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

b MR Special Subway Tile 230.00 sq m 3563.00 8,19,490.00

CARPET TILES: Providing and laying carpet tile flooring. Carpets shall be of Type 6 nylon loop pile carpet tiles/Plank. The carpet shall have sufficient gauge

(1/10 ~ 1/12) with sufficient stitches (10~13) per inch. The carpet shall be solution dyed fibre content or with injection printing technology. The carpet shall have

the pile height ranging from (2.0 ~ 3.0) mm with average density higher than 4500 Oz/ cubic yard. The total thickness of the carpet tile shall also range from (5.5

ITALIAN MARBLE: Providing and laying machine cut, mirror polished, Italian Marble brass brass inlay stone flooring laid in required pattern in linear portion of

the building all complete as per architectural drawings, with 18mm thick stone slab laid over 20mm (average) thick base of cement mortar 1: 4 (1 cement: 4

11.51 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble

shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

11.51.1 18 mm thick Italian Marble stone slab in all colour and shade 600.00 sq m 6603.35 39,62,010.00

IPS FLOORING: 52mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse

sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone

1.08 11.4 aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost 1600.00 sq m 978.45 15,65,520.00

of cement slurry, but excluding the cost of nosing of steps etc. complete.

2 Digitally signed by

PRADYUMNA MUKHERJEE

TOTAL FLOORING WORKS 1,33,84,433.18 1,01,14,676.00

2 FALSE CEILING WORKS

GYPSUM BOARD CEILING: Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed

from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6

mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm

dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger

fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge

of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate

channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high

having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall

2.01 12.45 screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230

mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing

with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification

and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per

drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with

12.45.1 12.5mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) 1870.00 sq m 1355.80 25,35,346.00

WOODEN VENEER / BAMBOO CEILING : Providing and fixing wooden veneer / bamboo ceiling by Fixing Natural OAK Veneer 4 mm / natural bamboo

2.02 MR shoots, mesh, screens, gall screen complete as per the design on 12mm UnderlayFire retardent Ply fixed to a subframe made using 50mm X 50mm Kiln 900.00 sq m 8223.00 74,00,700.00

seasoned and chemically treated hollock wood fixed to RCC ceiilng using Fastners .

POLISH : Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence

as detailed below:

1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos.

2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs.

3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth

after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4

to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs.

2.03 MR 4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion.This 1st coat is allowed 900.00 sq m 2467.00 22,20,300.00

to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with

compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete coat to be done in 1 or 2 layers without

gap of time.) as per direction of Engineer-in-Charge.

GYPSUM LOUVERED CEILING: 12.5x600x600 high grade, glass-fibre reinforced, acoustic, gypsum panel with acoustic perforation as Unity 3 - square

3.5x3.5mm c/c 8.33 type U3. The ROLD 12 tiles with Strip shall be screw fixed on minimum 60mm wood or steel furring. The ROLD 12 with strips tiles are with

edge B+ and are pre-painted ready for installation on site. ROLD 12 screws, type Torx 15, with white-painted head are used for screw-fixing. The acoustic

2.04 MR ROLD 12 tiles are furnished with a grey (white) absorbent felt backing with an airflow resistance of 330-460 Ns/m³ (DIN 53887).Colour - White, NCS 0701 140.00 sq m 19188.00 26,86,320.00

Y24R, gloss 5 (standard) or re-paintable at site with water based acrylic paint.Closest match for repainting: NCS 0700/RAL 9003. Paint Type -

Waterbased acrylic emulsion paint including titanium for hygienic indoor climate. Light Reflection: 69.2% according to DIN Norm 5036.Acoustic Property - αw:

0.95; NRC: 0.90.Fire Class - A2-s1,d0 .Suspension - The ROLD 12 must be screw fixed to furring of 22 mm wood or 60mm steel battens at 300 mm c/c.

ACOUSTIC CEILING: Providing and Fixing of 18 mm PET Panels with a density of 1850 gsm, material -100% polyester fibre, 100% recyclable and highly

2.05 MR durable with GI U channel and clutch wire for hanging. The shape and sizes shall be as per the approved design and drawings complete in all respect. 218.00 sq m 4112.00 8,96,416.00

3 Digitally signed by

PRADYUMNA MUKHERJEE

WOOD GRILLE CEILING & WALL PANELLING: Providing & fixing of Knauf WoodWorks Grille with backer made of compressed natural bamboo with Knauf

24mm Prelude 43 black exposed grid. The Grille panels shall be made of rapidly renewable natural bamboo core having density 600+Kgs/m3 as per BS EN323

(1993) and bending strength of 96+ N/mm2 as per BS EN310 (1993). The Grille panel shall have a seven layer UV coating of thickness 0.09-0.11mm as per BS

EN71 finished to natural or carbonized shades. The Grille panel shall be of nominal size 35x300x2400mm comprising 8 blades/slats of 35x16x2376mm with

centre to centre spacing of 37.5mm fixed through Backer of size 12x22x300mm having centre to centre spacing of 300mm and additional end backers at

150mm from both the edges. Ledger of 6.5x24x2400mm shall be used for covering face of wall angle. Open edges shall be covered using Edge Caps of

44x19x2400mm and Blade Junction of 66x38x2400mm shall be used along the connection of two Grille panels. The Grille panel when used with Knauf 20mm

Optra Black Glasswool infill panels shall have an NRC of 0.9 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz)

as per ASTM C423. The Grille panel shall have a fire performance of Class B according to EN13501-1. The Grille panel shall have moisture content of 8-14% as

per IS 1708 (Part 1):1986 and a Humidity Resistance (RH) of 70%. SUSPENSION: The tile shall be installed on Knauf Prelude 43 Black with 24 mm wide T -

section flanges having rotary stitching on all T sections i.e., the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 43mm, 35mm and 30mm

respectively. The deflection loading of the system shall be 17.8 kg/m2 (as per standard installation layout mentioned below) and main beam tested as per ASTM

C635 (Deflection limit less than L/360) with a deflection loading of 21.4kg/m. The end details of the main beam and cross tee shall be made of pre hardened

steel fixed to the ends. The cross tee to provide double locking between “cross tee to cross tee” and “cross tee to main beam”. All main beam to main beam and

cross tee to cross tee connection shall have a pull out strength of more than 100kg. The T Sections shall be made of hot dipped galvanized steel of 100 gsm as

per IS 277 (2003) and pre-painted steel with baked polyester paint with 0T bending capability. All exposed panel ends to be covered using edge caps. All wall

2.06 MR angles to be covered using ledgers. Installation should be carried out as per Knauf recommended procedure. The grid shall be installed with suspension system 100.00 sq m 22066.00 22,06,600.00

of Knauf make. INSTALLATION: To comprise main runner spaced at 1200mm centre to centre securely fixed to the structural soffit using Knauf suspension

system (specifications below) at 1200mm maximum centre. The First/Last Knauf suspension system at the end of each main runner should not be greater than

450mm from the adjacent wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre to form 1200 x 600 mm module.

Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally

between the 1200 mm cross tees. Perimeter trim to be Knauf wall angles of size 3000x19x19mm, secured to walls at 450 mm maximum centre to centre.Metal

spring backer clips shall be used to fix the Grille panel to suspension with a grid formation of 600mm along the blade/slat and 2 pieces along each backer (total 8

clips per full panel size) for every individual panel. Raise the panel up against the suspension system and align the backers with the suspension system. Push

upwards on the spring backer clip to engage the clip tabs on to the suspension system flange. Ensure that both clip tabs engage the suspension system

flange.KNAUF SUSPENSION SYSTEM accessories manufactured and supplied by Knauf consisting of M6 Anchor Fasteners with hanger hole,

pre–Straightened Hanger wire of dia – 2.5 mm of 1.80 m length having a tensile strength of 344-413 MPa and a minimum loading strength of 110 kgs.

Additionally, adjustable hook clips made of 0.7mm thick Grade 1 C55 galvanized spring steel of dimension 100 x 20mm and 4 mm aquiline wire to be used for

level adjustment during installation purpose in main runners.

PERFORATED GYPSUM CORRIDOR CEILING: Supply and installation of Danoline acoustic self supporting ceilings – Corridor 400 - 9.5x400x1800mm high

grade, glass fibre reinforced, acoustic, white painted, gypsum panel with acoustic perforation,as Micro - round 6x6mm c/c 15mm type NRC - 0.70, Corridor 400

panels are with integrated metal profile on the back, to be installed in free span without suspension hangers.

The tiles are furnished with a grey/white absorbent felt backing with an airflow resistance of 330-460 Ns/m³ (DIN 53887). RH - 90% LR - 82.6% Fire Class A2-

2.07 MR s1,d0 SUSPENSION - The flex-profile is an integrated part of the Corridor ceiling plank. The suspension system from approved manufacturers consists of 490.00 sq m 5893.00 28,87,570.00

reinforced wall angles and 38mm main runners are used between sections and lines of Corridor planks.

Cleaneo Technology - Air purification & Air quality.Active reduction of air polluants thanks to Cleaneo Technology effectively reduces concentrations of VOC’s

like alcohol, aldehydes, ketons and esters as well as unpleasant odours from e.g. food or cigarette smoke. Air purification properties tested according to CEN

standards and VDI guidelines by Fraunhof Insistute for Building Physics

PERFORATED GYPSUM BOARD CEILING: Providing and fixing suspended false ceiling- Danoline: Solopanel Size 1188x1998x12.5mm Globe perforation 8/18

with 8.7% perforation with NRC upto 0.6 : Regular round perforation of glass fibre reinforced gypsum material, which includes providing and fixing GI perimeter

channels of size 0.55 mm. Thk. having one flange of 20 mm and another flange of 30 mm and web of 27 mm along the perimeter of the ceiling, screw fixed to

brick wall/ partition with help of nylon sleeves and screws, at 610 mm centers. The suspended GI intermediate channels of size 45 mm,0.9mm thk with two

flanges of 15 mm each from the soffit at 900 mm centers with ceiling angle of width 25mm x 10mm x 0.55mm thk fixed to soffit with GI cleat and steel expansion

fasteners. Ceiling section of 0.55 mm thk having web of 51.5mm & two flanges of 26mm each with lips of 10.5mm are fixed to the intermediate channels with

2.08 MR help of connecting clips and in direction perpendicular to the intermediate channel with centers of 333 mm perforated gypboard is then screw fixed to ceiling 768.00 sq m 3152.00 24,20,736.00

section with 25 mm dry wall screws at 300 mm centers to G.I. framing in perfect level. Screw fixing is done mechanically either with screw driver or drilling

machine with suitable attachment. Finally the boards are to be joined and finished so as to have a flush look with uniflot.

Cleaneo Technology - Air purification & Air quality.Active reduction of air polluants thanks to Cleaneo Technology effectively reduces concentrations of VOC’s

like alcohol, aldehydes, ketons and esters as well as unpleasant odours from e.g. food or cigarette smoke

Air purification properties tested according to CEN standards and VDI guidelines by Fraunhof Insistute for Building Physics.

The false ceiling surfaces shall be prepared to the satisfaction of the Architect, and shall be applied with two coats of primer to the satisfaction of Architects.

300X1200 SUSPENDED FALSE CEILING : Providing and fixing suspended false ceiling microlook tegular edge tile with 15 mm thickness ,easily demountable

tile , manufactured from High density glass wool , visible surface is a batch painted glass tissue in white, back of the tile covered with glass tissue. Size

1200x600x15mm Acoustics-Sound absorption(Alpha W) - 0.95 at 200 mm o.d.s as per EN ISO 354 Acoustics-Sound absorption Class - Class A at 200 mm

2.09 MR o.d.s as per EN ISO 11654Acoustics-Articulation class - 180 as per ASTM E1111, ASTM E1110,NRC - 0.9 NRC as per ASTM C 423,Humidity Resistance - 415.00 sq m 3084.00 12,79,860.00

Permanent ambient RH up to 95% at 30*C without sagging, warping and delaminating ( 13964:2014). Fire Safety - Tested and classified as non combustible

according to EN ISO 1182 with reaction to fire classification class A2 s1 d0 according to EN 13501-1 - European Standard.

4 Digitally signed by

PRADYUMNA MUKHERJEE

METAL CEILING FOR WET AREAS : Providing and fixing G.I Plain 84mm wide x12mm deep panel with 16 mm flush profile to make it 100mm module of

length upto 6mtr, shall be roll formed out of 0.5mm thick Powder Coated .The top coat of panel shall be 60 micron polyester coated finish in approved colour.

2.10 MR The panel shall be factory cut in up to 6Mtr OR required length. Accessories Detail:Carrier: 32 mm wide and 39mm deep, made out of 0.5mm thick steel backed 415.00 sq m 2741.00 11,37,515.00

with enameled black paint having cut out to hold on panel in a module of 100mm closed. The joint of two carriers shall be joined by means of carrier splices

maintaining a module of 100mm .4mm dia galvanized rod with special height adjustment butter fly clips made out of SS steel sheet. The edge profile G.I.shall be

matching with the panel.

LOUVERED WOODEN WALL PANELS: Providing and fixing ACOUSTIC WALL PANELS. The MDF wall panels shall be composed of Medium Density

Fiber board (MDF) with a minimum density exceeding 710 kgs/m³, and they shall be covered with PP foil of Renolit, Germany brand/make with a thickness of

120 microns. The adhesive used for affixing the panels must be PUR (polyurethane) hotmelt glue, and the design of the panels will be as per the specifications

provided by the architect. The dimensions of the panels are 17-18mm in thickness, 130.5mm in width, and 2745mm in length.The scope of work includes

providing and fixing these MDF wall panels onto a framework constructed either from MDF or plywood. The framework should have a thickness of 50 mm and a

width ranging from 8mm to 12mm. The installation of the panels can be executed through either the nail-down method or the pasting method, with the use of a

high bonding adhesive suitable for MDF and plywood, NRC 0.65 upto 1 NRC . The finishing of the MDF wall panels should adhere to the approved architectural

drawings and the directions provided by the Engineer-in-Charge (EIC).

TERRACOTTA TILES WALL CLADDING : Providing and Fixing customised decorative tile cladding as per the approved drawing and pattern complete. Tiles of

various sizes and patterns with average thickness of 1.5 inches.

TOTAL FALSE CEILING WORKS 25,35,346.00 2,49,65,608.25

3 WALL FINISHES WORKS

GLASS PARTITION (FIXED DOUBLE GLAZED GLASS PARTITION): Supply & Installation of Aluminum profile with top & bottom profiles of size 82mm x

38mm in Natural Anodized / Black finish. Partition sides to be fixed with mullion and it's covers should be easily accesible while removal of glass, if & when

required. Glass to be fixed with suitable EPDM gaskets for insertion of combination of 10mm thick clear toughened glass + 58 to 62 mm Air Gap + 12 mm thick

clear Toughened Glass. Glass should not placed directly on profiles for giving more strength. It should be placed on aluminium spacer profiles and spacers

3.01 MR should be covered with cover profiles. Partition Glass joineries consists of two-way Polycarbonate I-profiles, 90 Degree Polycarbonate L-Junction and 600.00 sq m 16447.00 98,68,200.00

Polycarbonate T-Junction profiles. Polycarbonate profile joineries to be fixed with double sided adhesive tape & profiles to be inserted in the joint instead of

sealing it with sealants. Polycarbonate profiles to be used to give continuity glass effect. Hardware for fixing profiles to be used as per manufacturer standard.

Profile & hardware should be from same brand to give end to end solution. Costs should be inclusive of necessary Hardware for fixing of profiles & installation

FRAMED HINGED GLASS DOOR: Supply & Installation of Framed Hinged Door with Profile size of 55x32mm along with necessary seals. Doors to be fixed on

Hinges & Lock with lever handle for rebated door in matt black/ natural Alu finish with Top Mounted Door Closer along with Slide Channel on Top and saddle

plate for fixing on the Glass door suitable for 10mm thick clear toughened glass. Necessary seals to be provided all around the doorframe. Necessary

3.02 MR Hardwares includes Lock with Lever Handles, Seals, Hinges & door closers as per manufacturer's standard. Installation rates should be inclusive and vendor 75 Nos. 82234.00 61,67,550.00

shall provide end to end solution.

WOODEN DOOR FRAMES: Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with

9.1 hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).

9.1.1 Second class teak wood 0.30 cu m 142949.70 43,528.18

WOODEN BATTENS: Providing and fixing specified wood frame work consisting of battens 50x25mm fixed with rawl plug and drilling necessary holes for rawl

3.04 plug etc. including priming coat complete.

8.27.1 Kiln seasoned and chemically treated hollock wood 3.00 CUM 187277.65 5,61,832.95

FLUSH DOOR SHUTTERS: Providing and fixing on all height prefabricated factory made 32 mm thick flush door shutter in existing door frame bounded with

BWP type synthetic resin adhesive & wooden fillers as per IS 848 -1974 shutter should be confirm IS:2202 (part-1) non decorative type flush door of area up to

1.80 to 2.50 sqm and nothing shall be paid on account of size variation upto 5% plus mimus of make with both side 4mm thick decorative teak veneering of

make sapele/white american oak/vintage teak including fixing on all edges 8mm thick second class teak wood margin/lipping with 8 mm thick clear

vision/frosted glass fitted vertically in flush door shutter of make Saint Gobin, Modi Guard & Hindustan National Glass fixed all-round by 4mm thick second class

teak wood margin/molding and size of cut in flush door shutter will be approx. 200x1800mm or as per approved drawing and one no. of door rubbershutter

finished complete with PU polish all-round i/c SS butt hinges and SS screws all complete as per the direction of engineer-in-charge. (Note: this item is inclusive

of all material, T&P and labour involved and the work shall be executed as per the approved drawing).

WOODEN LIPPING: Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of

door shutter to be measured).

FLUSH DOOR FLOOR MACHINE : Providing Double cylinder Floor Spring D-120 for Wooden door with Closing Force EN 4 with Maximum door weight 120

3.07 MR Kg. Maximum door width 1250 mm.Closing speed : 130° Final closing speed : 15-0°. Hold Open (standard): 90° hold open. Weight of floor spring approx : 6kg, 29 SET 15039.00 4,36,131.00

5,00,000 cycles Tested. approved make and model all complete as per the direction of Engineer-in-charge.

TOP & BOTTOM STRAP : Providing top and Bottom Strap for wooden doors of approved make and model all complete as per the direction of Engineer-in-

5 Digitally signed by

PRADYUMNA MUKHERJEE

FLUSH DOOR DEAD LOCK : Providing and Fixing 160 mm Euro Dead lock with Rose rings for wooden doors of approved make and model all complete as

per the direction of Engineer-in-charge.

FLUSH DOOR LOCK CYLINDER : Providing and Fixing 60 mm Eco Pin Cylinder 1CK SS Cylinder One side knob and one side regular key for wooden doors

of approved make and model all complete as per the direction of Engineer-in-charge.

FLUSH DOOR HANDLE : Providing 32x840 mm SS 304 H type Handle for wooden doors. Material : Stainless Steel.

Finish : Satin Stainless Steel (SSS). of approved make and model all complete as per the direction of Engineer-in-charge.

WOODEN DOOR LOCK: Providing and Fixing Dead lock Back set- 50 mm with Key Hole of approved make and model all complete as per the direction of

Engineer-in-charge.

GLASS FILMS: Providing & Fixing Frosted Translucent, cast PVC, self-adhesive vinyl, special CRYSTAL-effect film to reproduce Sand-blasting effect on glass

with customised designs, thickness of 2 mil (0.05mm) without adhesive & 3mil (0.8)with adhesive having minimum tensile strength of 3.5 pound/inch at 73 F(0.6

kg/cm at 23 C). Adhesion after 24hrs of installation should be 4 pounds/inch (0.7 kg/cm) on Acrylic, Glass Polycarbonate: MCS warranty of 3yrs (if exposed to

direct sunlight) to 15yrs (indoors) .

TOILET DOOR MORTIZE LOCK : Providing and Fixing ss 304 D Type Tube Lever Mortise Combi SET with 60 mm Cylinder keyless and Lock Body SS for

wooden Toilet doors of approved make and model all complete as per the direction of Engineer-in-charge.

TOILET DOOR LOCK BODY : Providing and Fixing 240 mm lock body for wooden doors of approved make and model all complete as per the direction of

Engineer-in-charge.

TOILET DOOR CLOSER : Providing and Fixing Door closer Hercules -60 kg for wooden doors of approved make and model all complete as per the direction

of Engineer-in-charge.

TOILET DOOR HINGES : Providing and Fixing SS 304 Hinges Four Ball Bearing 100x75x3 mm (with screws) for wooden doors of approved make and model

all complete as per the direction of Engineer-in-charge.

LACQUERED GLASS: Providing and fixing of 6mm thick annealed SGG Planilaque Evolution (premium GRIHA rated lacquered glass from Saint-Gobain) of

approved color by Architect/ Client / Customer, fixed with SGG ULTRAFIX (compatible neutral core silicon/ double sided tape) on a perfectly leveled 12mm

thick water proof marine plywood / MDF / Mineral fibre board which is mounted on the RCC wall/any other structure. Lacquered glass must be made industrially

(via curtain coating process); opaque (if viewed against a support wall), coated with PU lacquer (50 micron thick); color consistency (measured by Minolta

3.18 MR spectrophotometer CM5081); highly durable (passes PERSOZ hardness test for minimum 220 oscillatios); humid resistant (conforms to BS EN 1036 1999); 450.00 SQM 5004.00 22,51,800.00

environmentally friendly (no lead, no arsenic, no copper, noformaldehyde); appropriate recycled content (12% post industrial/ 6% post consumer); compressive

strength (1000 MPa) & tensile strength (40 MPa), same as float glass;

GYPSUM BOARD PARTITION: Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of

frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling

channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash

fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48mm wide having one flange of 34 mm

and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6

9.105 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at

3.19 spacing of 450mm centre to centre, and fixing of boards to both side of frame work by 25mm long dry wall screws on studs, floor and ceiling channels at the

spacing of 300mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99mm

width (0.9mm thick having two flanges of 9.5mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head

screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25mmx25mmx0.5mm), joint

finisher and two coats of primer suitable for board as per manufacturer's specification and direction of engineer in charge all complete.

75mm overall thickness partition with 12.5mm thick double skin fire rated Glass Reinforced Gypsum (GRG) plaster board conforming to IS: 2095: part 3 (Board

with BIS certification marks)

ACRYLIC SOLID SURFACE CLADDING: Supply & Installation of 12 mm thick Thermoformable Acrylic Solid Surface Sheets (DuPont Corian/ Tristone/ Lotte),

over a robust substrate made out of BWP/ Flexi Ply/ MS- Aluminum sections etc. as required, to achieve stated design intent. ASS in 12mm thickness, shall be

manufactured as per guidelines of ISO 19712. ASS sheets to be cut, pasted and finished over the substrate as provided, to achieve smooth and seamless

3.20 MR finish. Item cost include intend adaptation, supply, freight and installation of ASS sheets to site, wastage, finishing, creating provisions/ cut-outs for accessories 180.00 SQM 8635.00 15,54,300.00

and final placement of table. Work shall be done by company's authorized Quality Network (QN) fabricator, as per satisfaction of Engineer-in-Charge. Colours :

Basic, Solid and small speckled (Group I & 2)

6 Digitally signed by

PRADYUMNA MUKHERJEE

WINDOW BLINDS : Providing & supplying of Window Blinds as per the approved sample double honeycomb shades having honeycomb within

honeycomb with easy rise operating system as per following specifications fabric specifications:

• Original Non-woven honeycomb shade shaving soft fabric appearance and high energy-efficient fabric with high tear strength constructed out of

Anti-static, resilent, colour fast & Sanitized Treat 100% spun bonded non-woven polyester fiber & precision manufacture to form a hexagonally shaped

duette pleat. The Fabric is GREENGUARD certified and can attain an NRC value of 0.75. Certificates to be provided at the time of delivery of material at site.

Pleat dimension ¾ ”Honeycomb within a Honeycomb” with 3 air pockets for maximum energy efficiency.

• Shadings are duotone, with neutral tone facing the exterior and color facing the interior The Head rail. Shall measure 50 wide and 35mm deep & thick

1.25mm extruded from alu. alloy& shall be powder coated to a smooth finish with a thickness of 40 microns. Fabric shall be constructed from

spun-bonded polyester fiber, precision manufactured to form a hexagonally shaped, dual pleat, cellular construction. All cords & cord holes shall be

fully concealed inside the fabric structure. As each of the hexagonal cells is formed individually, pleats operate independent of each other providing

superior pleat retention & structure strength. Installation brackets. shall be of high-tension spring steel suitable for overhead & wall mounting 30mm Duette

Hartford mounting bracket. Head rail covered with Sydney Valance of height 80mm made up of Aluminium & L shape moving Rail includes “Click & Engage"

method of dimension 50mmx55mmsticked with integrated moving rail magnets provide a streamlined look, reduce centre light gap, and promote easier

operation. Polyester cord. Shall be 0.9mm in diameter & of woven hollow core end cap shall be moulded acrylic color matched to the head & bottom rails.

Bottom rail shall be a single channel section, measuring 30mm wide and 12.5mmdeep & thickness 1-

1.2mm extruded from alu. Alloy & shall be powder coated with a smooth finish to a thickness of 15-25 microns. Hold-Down bracket (optional) shall be molded

in clear acrylic. It incorporates a pin for engagement with the bottom rail end-cap. It shall be suitable for sill, face or side facing. Cord Equalizer shall be injection

melded from impact modified acrylic with a high flexural modulus

WINDOW BLINDS : Providing & supplying of fabric venetian Window Blinds as per the approved sample, consisting of 3" vane size having head rail, rotator rail

and bottom rail made of aluminium alloy 6063-T6 PER ASTM B221 - 85 extruded profile, powder coated and provided in standard natural white color. The rolling

tube should be made up of aluminium alloy from extruded profile of 34mm dia. The head rail dimensions should be of suitable size according to the length of

head rail and space available and finished with fabric cover matching with the louver fabric. The cassette should conceal the working mechanism rotary-clutch.

(White polycarbonate spring tempered rotary clutch which raises), lower and tilts the blinds. White polycarbonate limit assemblies control vane over-rotation,

3.21 A MR located on either side of individual blinds. The room darkening fabric of Blind should be of anti-static polyester vanes which have facings between two sheer 275.00 SQM 12952.00 35,61,800.00

layers (50 mm wide) to reduce glare. Sheer layers should be of white 100% knit polyester, the colors, textures and opacities as approved. The fabric shall be

made of spun- bonded 100% polyester fiber (having green guard certification) treated with soil & dust repellent requiring minimum regular interval cleaning.

GREEN GUARD Gold certified for low-emitting products to maintain Indoor environment. Up to 80% ultraviolet protection with vanes open and 90% with vanes

closed. The shading to be operated by Easy rise mechanism with a continuous cord loop operating system. All parts, components & hardware are in approved

shade as per direction of Engineer-incharge.

WINDOW BLINDS : Providing and fixing soft, elegant fashion and function of contour window shadings with 5 inches vanes that makes this remarkable window

covering a truly unique innovation. The blind has sheer fabric at the back and the vanes contract and expand giving an impression of vanes floating on the

sheer. The headrail and bottom rail are made of aluminum alloy extruded profile, powder coated and provided with same fabric as per the blind fabric

3.21B MR selection.Textured fabrics in a palette of delightful colours transform from cascading folds to contoured vanes, allowing a softened outside view through the 30.00 SQM 48166.30 14,44,989.00

sheer backing, while also providing excellent ultraviolet protection. The fabric opacity is room darkening with 5’’ vane size and comes with Six beautifully textured

fabric styles — India Silk, Linen, Satin, Satin Metallic, Shantung and Stria. The blind has matching fabric-covered headrail and bottom rail create a unified look

from top to bottom. The headrail conceals and protects the shading when raised — no fabric stack to obstruct the outside view.

PELMET: Fabricate and install pelmet made of 19mm thick board, up to 300mm high and in line with external glazing as per details of Architect. Rate to include

finishing exposed surfaces of the Pelmet with 1mm laminate.

ZINC CLADDING : Supply & Installation of ZINC Titanium (conforming to EN 988 stndards) Interlocking wall cladding panels in VMZINC Pigmento Finish. The

wall cladding system shall comprise of the following as described .ZINC 0.8 mm interlocking panels of 233 mm width and max 2000 mm length. Panels are

formed with interlocking lap at panel edges and smooth, flat pan; designed to be field assembled in sequential installation by engaging edges of each panel to

3.23 MR edge of adjacent panel. Panels are attached to supports/substrates using stainless screws located under edges of the panels The Panels Shall be Installed over

the Aluminium box Section of 50x25x1.6 mm thick @ 600mm c/c horizontal and vertical with Screws/ Rivets of suitable size as recommended by manufacturer

.THe zinc titanium manufacturer shall have regisetered office in India and shall have supplied zinc titanium cladding to government projects in last 5 years .

Installation to be carried out by manufacturer approved installation agencies who has completed zinc cladding projects in India. 0.00 SQ M 17269.00 -

3.23A MR Supply & Installation of ZINC Flashings in same finish and material for corners, top, botom, site detailing 0.00 RM 3139.00 -

13.26 Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete

13.85 Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.

13.85.3 With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre 200.00 sqm 73.95 14,790.00

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare

the surface even and smooth complete.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved

3.26 13.83 brand and manufacture, including applying additional coats wherever required to achieve even shade and colour

7 Digitally signed by

PRADYUMNA MUKHERJEE

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and

14.1 preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-

14.1.2 With cement mortar 1:4 (1cement: 4 coarse sand) 200.00 Sqm 560.50 1,12,100.00

5.5mm THICK HDHMR BOARD ( BOTH SIDE RAW): Providing and fixing in wall lining, partitions etc. Confirming to ASTM E-84-2021 class1 BOTH side raw,

3.28 MR having even grade low emission, high moisture resistance, fire resistance, borer, termite & fungus resistance, green material and environmental friendly with 150.00 Sqm 504.00 75,600.00

necessary fixing arrangement and screws etc. , complete as per direction of Engineer-in-Charge

5.5mm thick HDHMR Board

11 mm THICK HDMR BOARD ( BOTH SIDE RAW ): Providing and fixing 11mm thick HDHMR board in wall lining, partitions etc. both side raw. Extra density,

high moisture resistance, borer, termite & fungus resistance, green material and environmental friendly with necessary fixing arrangement and screws etc.

11 mm thick HDHMR Board 5100.00 SQM 1079.00 55,02,900.00

5.5mm THICK HDHMR BOARD ( ONE SIDE LAMINATE ): Providing and fixing in wall lining, partitions etc. Confirming to ASTM E-84-2021 class1 one side

1mm decorative Lamination and other side raw, having even grade low emission, high moisture resistance, fire resistance, borer, termite & fungus resistance,

3.30 MR green material and environmental friendly with necessary fixing arrangement and screws etc. , complete as per direction of Engineer-in-Charge

5.5mm thick HDHMR Board 3800.00 SQM 1347.00 51,18,600.00

ALUMINIUM FRAME: Providing and fixing partition, frame work in 50x25x1.5mm Aluminium Section placed at 600mm centre to centre both ways (horizontal &

3.31 MR vertical) fastened to floor, ceiling and horizontal member. The item includes providing and fixing 50mm thick polyester synthetic insulation as insulation of 100 2600.00 SQM 1347.00 35,02,200.00

FIBRE WALL COVERING: Supply & Installation of Glass fiber based homogenous Woven/ non-woven .1mm thick, 100-200 GSM Density brethable Wall

Coverings. Material to be fire certified with minimum Euroclass BS1D0 certification under EN13501, no harmful chemical coated with Oekotex Standard 100

certification and non-toxic in nature for closed enviornments with A+ attested for emission in indoor air. Installation to be done over smooth, dry and dust-free

substrate as specified with OEM recommended adhesive by the supplier's authorized installer team. Installation measurement as per the entire area

(concealed/visible) installed. Finished as per satisfaction of E.I.C. PAINTABLE

ITALIAN MARBLE FOR WALL CLADDING: Providing and laying machine cut, mirror polished, Italian Marble brass brass inlay stone flooring laid in required

pattern in linear portion of the building all complete as per architectural drawings, with 18mm thick stone slab laid over 20mm (average) thick base of cement

3.33 11.51 mortar 1: 4 (1 cement: 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment

to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

11.51.1 18 mm thick Italian Marble stone slab in all colour and shade 103.35 SQM 6603.35 6,82,456.22

3D ACOUSTIC PET WALL PANELLING: Providing and fixing Smart Acoustical Wall Panels with square edges made of Polyester fiber substrate 12mm thick

with acoustical properties and with an option of 12 colours as per the choice of the Architect/ Person in-charge, providing a minimum sound absorption level of

0.50-0.90 NRC, to be affixed to wall using Adhesive. The material should adhere to Formaldehyde emission standards of GB18580-2001 class E1, asbestos-

3.34 MR free, non-toxic, non-irritant and recyclable. Material to have fire resistance as per B1 Chinese standards. The sheets to have density of 200 kg/m3 and weight of 330.00 SQM 4317.00 14,24,610.00

2.0 kg/m2. The sheets to be made available as per the V groove design approved by Architect/ Person in charge(attached Pic). Cutting to be in done by supplier

using blade cutting as per requirement.

LAMINATE PANELLING: Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density

3.35 protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

TOTAL WALL FINISHING WORKS 95,49,010.86 4,84,20,050.93

4 MISCELLANEOUS WORKS

MODULAR KITCHEN - UNDER COUNTER STORAGE CABINETS:

Modular kitchen - Under counter storage cabinets:

Providing & fixing factory made modular kitchen cabinets in modular type knockable cabinet boxes with openable shutters and sufficient number of drawers

made of 18 mm thk.HDHMR board with lamination in frosty white laminate with 0.8 mm laminate complete with 0.8 mm edge banding.All shelves should be

supported on approved quality SS pins and shall be adjustable for different heights as per requirements.Shutters and drawers fascia shall be at least 18mm thic

4.01 MR with laminate on both sides with 18mm wide 2mm thick PVC edge banding, All Shutters/ drawers finished in high gloss acrylic of approved make- 40.00 SQM 21994.00 8,79,760.00

Rehau,Ornare,Senosan and having handless profiles.The cabinet boxes of floor units will be supported by 100mm height vertical adjustable legs (Hettich make)

which will be covered with PVC skirting (Rehau or equivalent make) in brushed aluminum finish attached by hardware of skirting. The unit shall be fixed to the

floor/ wall/slab using metal screws of appropriate size and raw plugs. Only front face area of cabinets and skirting from floor to top of boxes shall be considered

for measurement and payment. Cabinet boxes size would be varies from 400x580x710MM to 1000x580x710MM (approx.) and join together as per site

requirements etc. Handle Profile, Aluminum Handle Profile for lift ups, O* Hinges, Corner Hinges, PVC legs, Skirting, Connector, Screws, Wall Mount set

complete all as per the direction of Engineer-in-Charge.

8 Digitally signed by

PRADYUMNA MUKHERJEE

MODULAR KITCHEN - OVERHEAD STORAGE WALL UNITS:

Modular Kitchen - Overhead storage wall units:

Providing & fixing factory made modular kitchen cabinets in modular type knockable cabinet boxes with openable shutters and sufficient number of drawers

made of 18 mm thk. HDHMR board with lamination in frosty white laminate with 0.8 mm laminate complete with 0.8 mm edge banding.All shelves should be

supported on approved quality SS pins and shall be adjustable for different heights as per requirements.Shutters and drawers fascia shall be at least 18mm thic

with laminate on both sides with 18mm wide 2mm thick PVC edge banding, All Shutters/ drawers finished in high gloss acrylic of approved make-

Rehau,Ornare,Senosan and having handless profiles. The unit shall be fixed to the floor/ wall/slab using metal screws of appropriate size and raw plugs. Only

front face area of cabinets and skirting from floor to top of boxes shall be considered for measurement and payment. Cabinet boxes size would be varies from

400X320X710MM to 1000X320X710MM (approx.) and join together as per site requirements etc. Handle Profile,Aluminum Handle Profile for lift ups,O*

Hinges,Corner Hinges,PVC legs,Skirting,Connector,Screw,Wall Mount set. Complete all as per the direction of Engineer in Charge.

4.02A MR Providing and fixing of Innotech with metal sides and quadro channels .Make.Hettich,Samsung,Irex,Hafale 30 Each 7943.00 2,38,290.00

4.02B MR Providing and fixing of Bottle pulout 200mm. Make Hettich, Samsung,Irex,Hafale 10 Each 12335.00 1,23,350.00

WATERPROOFING: Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like

(i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including

rounding off junction of vertical and horizontal surface.

4.03 22.3 (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off 73.08 SQM 769.60 56,242.37

junction of vertical and horizontal surface.

(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.

(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

Preparation of complete set of drawings based on the concept drawings including finishing, MEP services, details, design calculations etc. and for preparation of

4.04 MR as built drawing any other details as and when desired by Engineer Incharge/ client. A qualified professional for the purpose shall be appointed after due 1.00 LS 4000000.00 40,00,000.00

approval from Engineer-In-Charge.

Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting,

unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge. Note - item to be applicable

in urban areas having directions for restricted hours for movement/ plying of load carrying motor vehicle of 3.5 cum or more.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-lll) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

5.9 Centering and shuttering including strutting, propping etc. and removal of form for

5.9.1 Foundations, footings, bases of columns, etc. for mass concrete 10.00 sqm 392.15 3,922.00

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. 10.00 kg 107.85 1,079.00

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and

6.4.1 Cement mortar 1:4 (1 cement : 4 coarse sand) 79.80 cum 9344.35 7,45,679.00

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.

6.13.1 Cement mortar 1: 3 (1 cement: 3 coarse sand) 15.00 sqm 1150.50 17,258.00

DEMOLITION & DISMANTLING WORKS

Demolition of brickwork manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead

as per the direction of the engineer in charge

Dismantling door, windows and clerestory widows (steel or wood) shutter including chowkats, architrave, holdfasts etc complete and stacking within 50 metres

CUSTOMISED STORAGE UNIT : Supply and fixing of full height storage units (upto 450mm depth) made out of 18mm plywood finished with approved .8mm

laminate on the inside and outside. Hardware used of Hettich make.Compleate as per the direction of Engineer in charge

9 Digitally signed by

PRADYUMNA MUKHERJEE

FIRE GLASS WITH FRAME - Supply & Installation of Frame with Glass , Firetech cold- formed steel frame with 120 minutes of integrity and radiation control

(EW120). The system confirms to IS:3614 (Part II) or EN 1634-1:1999, tested and certified. The frame shall be finished with a approved fire resistant primer or

powder coating in desired shade as per the direction of Engineer- incharge. Glass - The glass should be 13mm clear 120 min fire rated for integrity, Radiation

4.19 MR control (EW120) and partial insulation (EI30), Non wired toughened interlayed glass with a light transmission of 86%, U-value of 5.0W/Sqmt K, solar factory of 0.00 SQM 64417.00 -

0.72, energy transmission 66% and a sound reduction of 38 (-1, -2) dB and compliant to class 1 (B) 1 category of Impact resistance as per EN 12600. The glass

shall provide bi-directional (Symmetrical) fire protection.

4.20 MR RUGS : Providing and Installation of Hand Tuff Rugs in colours as per the selection of the architect,

Size (ft): 8X8 INR Shape: Round : material wool & viscose 0 Nos. 51200 -

Size: 8'0(W) x 6’0(L)Feet Shape: RCT Construction: Hand Knotted 1 15.00 Material: Wool & Bamboo Silk 0 Nos. 60000 -

ECORESIN PANEL: Providing of Ecoresin panel of size 1220mm x 2440mm with variety of inlay between panels of specified Gauge. The panels are made from

ecoresin sheet with engineered polyester resin with a thickness of 9.0/10 mm with a top/ bottom finish as sandstone finish. The product conforms to Class A

4.21 MR impact rating in accordance as measured under ASTM standards is GreenguardTM Indoor Air Quality certified and has a minimum of 40% post-industrial 0 Nos. 530000 -

recycle content certified by a recognized 3rd party certification group, such as Scientific Certification Systems (SCS). The design of the product is based on

Varia produced with ecoresinTM as per approved make as per specification & approval of Engineer-in-charge.

TEXTURE PAINT : Finishing walls/ ceiling with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 Itr/10

4.22 13.45 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm 350 SQM 223.6 78,260.00

TOTAL MISCELLANEOUS WORKS 9,79,094.37 1,19,66,523.40

10 Digitally signed by

PRADYUMNA MUKHERJEE

SCHEDULE OF QUANTITIES - SANITARY & PLUMBING WORKS

DSR NO S NO DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

DSR NO S NO DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT TOTAL AMOUNT

2023 DSR (INR) NON-DSR (INR)

Supply, Installation, Testing and Commisioning of SINGLE LEVER CONCEALED BASIN MIXER

(WALL MOUNTED) WITH SPOUT (COMPOSITE ONE PIECE BODY)

MR 2 Supply, Installation, Testing and Commisioning of TABLE TOP BASIN, SIZE: 630x460x130mm EACH 30 20890.00 626700.00

Supply, Installation, Testing and Commisioning of Vessel type TABLE TOP BASIN having minimum

MR 3 SIZE: 630x460x130mm thinner edges and rimless bowl as per the color choice of the engineer in EACH 6 45000.00 270000.00

Supply, Installation, Testing and Commisioing of suitable compatible WASTE COUPLING 32MM-

FULL THREAD- WITH CERAMIC CAP-*130MM HEIGHT *65MM CERAMIC CAP

Supply, Installation, Testing and Commisioing of BOTTLE TRAP (WITH INTERNAL PARTITION)

MR 5 32mm SIZE WITH 300mm & 190mm LONG WALL CONNECTION PIPES & WALL FLANGE EACH 45 3284.00 147780.00

Supply, Installation, Testing and Commisiong of RIMLESS, BLIND INSTALLATION WALL HUNG

MR 6 WC WITH UF SOFT CLOSE SLIM SEAT COVER, HINGES AND ACCESSORIES SET, SIZE: EACH 65 15087.00 980655.00

Supply, Installation, Testing and Commisiong of smart WC having Rimless bowl and Advanced bidet

MR 7 functionality with massaging jets,Self-cleaning nozzle for improved hygiene,Heated seat for added EACH 6 60865.00 365190.00

comfort,Touchless control for easy adjustments,Auto-Open and Auto closed seat.

MR 8 Supply, Installation, Testing and Commisiong of PNEUMATIC CONTROL PLATE EACH 75 6641.00 498075.00

Supply, Installation, Testing and Commisiong of ANGULAR STOP COCK WITH WALL FLANGE

Supply, Installation, Testing and Commisiong of CONCEALED STOP COCK WITH ADJUSTABLE

WITH WALL FLANGE 15mm

Supply, Installation, Testing and Commisiong of HAND SHOWER (HEALTH FAUCET) WITH 8mm

MR 11 DIA 1.2 METER LONG FLEXIBLE TUBE EACH 75 2541.00 190575.00

Supply, Installation, Testing and Commisiong of PNEUMATIC SINGLE PIECE SLIM CONCEALED

MR 12 CISTERN BODY WITH INSTALLATION KIT & “S-TYPE” DRAIN PIPE CONNECTION SET FOR EACH 75 8044.00 603300.00

WALL HUNG WC (WITHOUT FLUSH CONTROL PLATE)

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings

17.28 complete.

13 Flexible pipe

Providing and fixing mirror of superior glass (of approved quality) complete with 6mm thick hard

board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved quality

15 conforming to IS : 8931

Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast (spun)

iron pipes and making good the same with cement concrete 1:3:6 (1 cement: 3 coarse sand: 6

17.61 graded stone aggregate 12.5 mm nominal size) including necessary plaster and pointing in cement

mortar 1:4 (1 cement : 4 coarse sand) :

18.76 Cutting holes upto 30x30cm in walls including making good the same.

18.76.1 With common burnt clay F.P.S. (non modular) bricks EACH 80 416.80 33344.00

Making chases upto 7.5 X 7.5 cm in walls including making good and finishing with matching surface

after housing G.I. pipe etc.

Digitally signed by

PRADYUMNA MUKHERJEE

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot &

cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with

clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent

cement and testing of joints complete as per direction of Engineer in Charge.

Internal work - Exposed on wall

18.7.2 19 20mm nominal outer dia pipes METRE 180 335.00 60300.00

18.7.3 25mm nominal outer dia pipes METRE 200 401.55 80310.00

18.7.4 32mm nominal outer dia pipes METRE 200 518.75 103750.00

18.7.5 40mm nominal outer dia pipes METRE 10 702.95 7029.50

18.7.6 50mm nominal outer dia pipes METRE 10 934.15 9341.50

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot &

cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at

1.00 m spacing.

18.8 This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting

chases and making good the same including testing of joints complete as per direction of Engineer in

Concealed work including cutting chases and making good the walls etc.,

18.8.1 15mm nominal outer dia pipes METRE 600 497.80 298680.00

18.8.2 20mm nominal outer dia pipes METRE 600 537.60 322560.00

18.8.3 25mm nominal outer dia pipes METRE 300 627.25 188175.00

18.8.4 32mm nominal outer dia pipes METRE 200 739.30 147860.00

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards

21 and weighing not less than 690 gms.

18.51.1 15 mm nominal bore EACH 18 798.95 14381.10

Providing, fixing, jointing and testing in position of ISI marked UV stabilized UPVC pipes for soil,

waste, and vent, Type-B as per IS : 13592 suitable for rubber ring joints, including all neccessary

specials and fittings (confirming to IS:14735) i.e. bends, tees, junctions (with or without doors),

reducers, WC connectors, couplers, expansion joints / bellows, cowels, clamps, rubber rings, clean

outs etc. fixing at wall/ ceiling/ floor level supported by clamp & hangers etc. in concealed / inside

duct / under floor & basement ceiling / external work etc. including chase cutting as required,

excavation and back filling in all kind of soils, suspended from floor under false ceiling or embedding

the pipes laid under floors / building in 75 mm. alround 1:2:4 cement concrete (1 cement : 2 coarse

22 sand : 4 graded stone aggregate 20 mm nominal size) including cost of shuttering for proper

completion of the work, breaking and making good the walls and floors etc. after pipes have been

duly laid and tested. The rubber ring shall confirm to IS:5382.

The Pipes will be supported with threaded G I rods & U clamps with nuts, washers etc on 50x50x5

mm slotted angle. The cost will include all support arrangements. The work includes commissioning

of all pipes lines as per drawings and specifications and as directed by engg-in-charge at site.

a 110 mm dia (Wall Thickness - 3.2 to 3.8 mm) METRE 600 536.00 321600.00

b 75 mm dia (Wall Thickness - 3.2 to 3.8 mm) METRE 200 416.00 83200.00

Providing, fixing, jointing and testing in position ISI marked (IS:4985) UPVC pipes of min 6 Kg/

Sqcm rating with fitting for waste pipe from fixtures to floor trap including reduces, enlarger, socket,

couplers, bends, tees etc including fixing at wall/ ceiling level supported by clamp & hangers etc.

cutting holes in wall/ floors/ slabs and making good the same with cement concrete 1:2:4 complete

Providing & fixing UPVC Floor trap of self cleansing design with stainless steel grating complete in

MR 24 all respects.

Digitally signed by

PRADYUMNA MUKHERJEE

Plain Floor Trap (4" Ht) with 50 / 75 outlet and with height raiser EACH 120 536.00 64320.00

MR 25 Extra for providing & fixing 125 mm dia C.P. grating in place of C.I. grating over floor traps. EACH 120 726.00 87120.00

Providing & fixing of SS Floor Cleanout, round or square with rubber seal and flat round cover with

screws and other required fitting complete as required.

Supply, Installation, testing and commisioning of toilet waste water super quiet portable pumping

station. Pump upto vertical 5 meters and horizontal 100 meter from toilet to vertical shaft with inlet

MR 27 connection in portable pump side inlet of 50, 75, 110 as per requirement to complete the work as per EACH 10 67430.00 674300.00

the directions of engineer in charge

Providing and fixing stainless steel tray below sewage pipe of size 200x200x200 mm of grade SS304

including all accessories

Supply, Installation, Testing and Commisiong of HIGH FLOW SINGLE LEVER CONCEALED

DIVERTOR FOR BATH & SHOWER

Supply, Installation, Testing and Commisiong of SPOUT FOR BUILT IN BATH/SHOWER MIXER

Supply, Installation, Testing and Commisiong of OVERHEAD SHOWER 350x350MM ROUND

MR 31 EDGE SQUARE HEAD SINGLE FLOW (BODY & FACE PLATE STAINLESS STEEL WITH EACH 6 24100.00 144600.00

CHROME PLATED) WITH RUBIT CLEANING SYSTEM

MR 32 Supply, Installation, Testing and Commissioning of 15 litre geyser EACH 30 12004.00 360120.00

MR 33 Supply, Installation, Testing and Commisiong of SOAP DISH HOLDER EACH 60 4392.00 263520.00

MR 34 Supply, Installation, Testing and Commisiong of TUMBLER HOLDER EACH 9 4309.00 38781.00

Supply, Installation, Testing and Commisiong of TOWEL RACK 600MM LONG WITH LOWER

MR 36 Supply, Installation, Testing and Commisiong of ROBE HOOK EACH 6 2045.00 12270.00

MR 37 Supply, Installation, Testing and Commisiong of TOILET ROLL HOLDER WITH COVER EACH 80 4978.00 398240.00

MR 38 Supply, Installation, Testing and Commisiong of TOWEL HOLDER EACH 15 3336.00 50040.00

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets

17.10 and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good

39 the walls wherever required :

17.10.1 Kitchen Sink with Drain Board

Supply, Installation, Testing and Commisiong of single lever sink mixer (table mounted) with

MR 40 extractable hand shower dual flow complete with 1.2 m long tube with 450 mm long braided hoses EACH 9 7571.00 68139.00

Providing and fixing white vitreous china water less urinal of size 600 x 330 x 315 mm having Each 24 18088.45 434122.80

17.79 41 antibacterial / germs free ceramic surface, fixed with cartridge having debris catcher and hygiene

Supply Installation, Testing and Commisioing of Handicap Toilet special fixtures to the complete

MR 42 satisfaction of the engineer in charge

(a) SITC of Grab Bar vertical swing white

(b) SITC of Grab Bar Left/Right 90 angle

(c ) SITC of Grab Bar 842mm long white Each 6 4664 27984.00

Digitally signed by

PRADYUMNA MUKHERJEE

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

DSR NO DESCRIPTION TOTAL AMOUNT TOTAL AMOUNT

DSR NO DESCRIPTION TOTAL AMOUNT TOTAL AMOUNT

S NO UNIT QUANTITY RATE

2022 DSR (INR) NON-DSR (INR)

A POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface / recessed medium class PVC

A.1 1.10 conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5

sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

Wiring for group controlled (looped) light point/ fan point/call bell point (without independent

switch etc.) with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in

A.2 1.55 surface / recessed PVC conduit, and earthing the point with 1.5 sq.mm. FRLS PVC insulated

copper conductor single core cable etc as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single

A.3 1.12 core cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq. mm FRLS Metre 59360 334.00 1,98,26,240.00

PVC insulated copper conductor single core cable for loop earthing as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch

box including connections but excluding modular plate etc. as required.

1.24.4 3 pin 5/6 amp socket outlet Each 1389 122.00 1,69,458.00

1.24.5 6 pin 15/16 amp socket outlet Each 230 197.00 45,310.00

Supplying and fixing modular blanking plate on the existing modular plate & switch box

excluding modular plate as required.

1.27 Supplying and fixing following size/module, GI box along with Modular base & cover plate on

existing modular metal boxes etc. as required.

B SUBMAIN AND CONTROL WIRING

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC

insulated copper conductor, single core cable in surface/ recessed medium class PVC

1.14.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre 50 334.00 16,700.00

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 50 439.00 21,950.00

Supplying and making end termination with brass compression gland and aluminium lugs for

9.1 following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1

KV grade as required.

Supply of following XPLE armourned 1.1 KV grade conforming to I.S.7098/1554Aluminium

MR Conductor Cables :

Supply of following sizes of PVC sheathed PVC/XLPE insulated Aluminium conductor

armoured cable of 1.1 KV grade conforming to IS:7098 part-1 / IS:1554 part-1 respectively & ISI

(d) 3.5 C x 50 Sqmm XLPE cable RM 170 510.00 86,700.00

(e) 3.5 C x 35 Sqmm XLPE cable RM 170 378.00 64,260.00

Supply of following sizes of copper cables -PVC sheathed PVC/XLPE insulated Copper

C.3 MR conductor armoured cable of 1.1 KV grade conforming to IS:7098 part-1 / IS:1554 part-1

respectively & ISI marked.

(a) 4 C x 16 Sqmm XLPE copper cable RM 750 1446.00 10,84,500.00

(b) 4 C x 25 Sqmm XLPE copper cable RM 180 2253.00 4,05,540.00

(c ) 3.5 C x 35 Sqmm XLPE copper cable RM 50 2686.00 1,34,300.00

(d) 3.5 C x 50 Sqmm XLPE copper cable RM 50 3224.00 1,61,200.00

D.1 2.11 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as Each 100 13.00

required. 1,300.00

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit

D.2 2.10 breaker suitable for inductive load of following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

2.13 Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB

complete with connections, testing and commissioning etc. as required.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB

2.4 distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral

bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as

required. (But without MCB/ RCCB/ Isolator)

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts,

2.14 residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in

the existing MCB DB complete with connections, testing and commissioning etc. as required.

E PROVISIONS FOR VOICE, DATA, SECURITY & TV SYSTEMS

E.1 Supply, installation, testing & Commissioning of 1 module 16A SWITCH SP 1 way for floor Set 12 216.00

E.2 MR Supply, installation, testing & Commissioning of 2 module 16 A Socket for floor box box. Set 12 577.00 6,924.00

Supply, installation, testing & Commissioning of Specific Backbox for Carpet for Floor Box

E.3 MR along with LID and TRIM for tiles/ marble 15 to 20mm thickness material for headband and Set 6 12106.00 72,636.00

single cable outlet/ glavanized steel, paint RAL 7031 for floor box .

Supply, installation, testing & Commissioning of Specific Backbox for Wooden Flooring for

E.4 MR Floor Box along with LID and TRIM for tiles/ marble 15 to 20mm thickness material for Set 7 6803.00 47,621.00

headband and single cable outlet/ glavanized steel, paint RAL 7031 for floor box.

E.5 Supply, installation, testing & Commissioning of flat support plate 8 module for integration of Set 12 263.00

MR Mechanism for Floor Box 3,156.00

Supply, installation, testing & Commissioning of waved support plates for 4 module (2x2)

modules for Floor Box

Supplying and fixing following modular switch / socket on the existing modular plate & switch

E.7 1.24 box including connections but excluding modular plate etc. as required.

1.24.7 TV socket outlet Set 80 148.00 11,840.00

Supply, Installation, Testing and Commisioning of Galavanized Iron (GI) Raceways along with

MR required suitable number of GI couplers for joining raceways and fixing GI brackets and all

accessories complete in all respect as per the directions of engineer in charge

(a) 300mmx38mm(GI) - 3 compartment Mtr 146 1738.00 2,53,748.00

E.9 (b) 225mmx38mm(GI) - 3 compartment Mtr 200 1420.00 2,84,000.00

Supply, Installation, Testing and Commisioning of Junction boxes for direct access to cables

at the intersection of raceways supplied completely with base and cover plates, height

MR adjustable junction box 65- 90 mm including all accessories ss plate of 3mm thick complete

E.10 in all respect as per the directions of engineer in charge

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE

E.11 1.19 insulated, shielded with fine tinned copper braid and protected with PVC sheath in the exisitng Meter 2400 47.00 1,12,800.00

surface/recessed steel/ PVC conduit as required

Supplying and fixing of following sizes medium class PVC conduit aong with accessories in

E.12 1.21 surface/ recess including cutting the wall and making good the same incase of recessed

conduit as required

Supplying and Installation of following size perforated of painting with powder coating M.S.

4.1 cable trays of perforation of not more than 17.5% in convinient sections, joined with connectors

E.13 suspended from the cieling with MS suspenders including bolts and nuts painting

suspenders etc as required

4.1.6 450 mm width x 50 mm depth x 2 mm thickness Metre 300 1137.00 3,41,100.00

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and

F.1 5.6 providing masonry enclosure with cover plate having locking arrangement and watering pipe SET 10 13838.00 1,38,380.00

of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as

F.4 5.16 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. MTR 2000 70.00 1,40,000.00

G PANEL BOARDS

G.2 MR Floor Panels / UPS Output Panel

Designing, fabricating, transporting, unloading, storing, fixing in position, testing and

commissioning the following sheet steel cubicle type panels fabricated from 1.6mm thick

CRCA sheet, dust and vermin proof, indoor type TPN Panels with hinged lockable doors

fabricated from 2mm thick CRCA sheet, suitable for 415V, 3 phase 4 wire 50Hz AC supply with

rear access for cable alley and with segregated bus-bar chamber with tinned aluminium bus

bar and including supplying and fixing following switchgears, meters and accessories, inter-

connections, bonding to earth, powder coated painting and marking as specified. Switch

boards complete as per schematic diagram:

Type of construction: Form 3

IP classification: 42

The LT PANEL shall be electrically inter-locked as shown in Schematic diagram and as

detailed in the Specifications

Colour: Gray Powder Coated, as per approved sample.

1 nos, 250 Amps. 4 pole MCCB , i.e four pole Moulded Case Circuit Breaker of fault breaking

capacity 25 KA (ICS=ICU up to 433 V) complete in all respect

TPN aluminum bus bars of minimum of 320 Amps capacity with heat shrinkable colored

sleeves and I/C DMC/SMC bus bars supports at required intervals complete for cross section,

size supports & their spacing etc. for withstanding fault level of 25 MVA for 1 Sec.

(a) 63 Amps, TPN, MCB - 4 Nos.

(b) 40 Amps, TPN, MCB - 10 nos

Panel complete as above Each 6 200000.00 12,00,000.00

G.3 MR HVAC Panel

Designing, fabricating, transporting, unloading, storing, fixing in position, testing and

commissioning the following sheet steel cubicle type panels fabricated from 1.6mm thick

CRCA sheet, dust and vermin proof, outdoor type TPN Panels, double door with canopy, with

hinged lockable doors fabricated from 2mm thick CRCA sheet, suitable for 415V, 3 phase 4

wire 50Hz AC supply with rear access for cable alley and with segregated bus-bar chamber

with tinned aluminium bus bar and including supplying and fixing following switchgears,

meters and accessories, inter-connections, bonding to earth, powder coated painting and

marking as specified. Switch boards complete as per schematic diagram:

Type of construction: Form 3

IP classification: 42

The LT PANEL shall be electrically inter-locked as shown in Schematic diagram and as

detailed in the Specifications

Colour: Gray Powder Coated, as per approved sample.

One (1) nos, 200 Amps. 4 pole MCCB and 2 nos. 63 Amps 4P MCCB, i.e four pole Moulded

Case Circuit Breaker of fault breaking capacity 25 KA (ICS=ICU up to 433 V) complete in all

TPN aluminum bus bars of minimum of 320 Amps capacity with heat shrinkable colored

sleeves and I/C DMC/SMC bus bars supports at required intervals complete for cross section,

size supports & their spacing etc. for withstanding fault level of 25 MVA for 1 Sec.

(a) 63 Amps, TPN, MCB - 4 nos

(b ) 40 Amps, TPN MCB - 10 nos

Panel complete as above Each 3 314297.00 9,42,891.00

H SAFETY ITEMS

Providing and fixing MV danger notice plate of 200mm x 150mm made of mild steel, atleast 2

H.1 2.21 mm thick, and vitreos enamelled white on both sides and with iscription in single red colour Nos. 6 269.00 1,614.00

on front side as required

I MR UPS SYSTEM

a Supply, Installation, Testing and Commissiong of Hot-swappable Modular Type 75KVA

Modular UPS with 125KVA Cabinet & 3Nos of 25KVA Module + 1No of 25KVA redundant

Module ) 3PH/3PH True Online Double Conversion UPS

b) Switch Panel-IP,OP & BY

c) MODBUS for BMS integration

d) Inbuilt Manual Bypass Switch

e) DC Cable from UPS to Battery Bank ( 10m)

f) Phase sequence correction & protection

g) Battery breaker with the battery cabinet, complete with 5 years warranty

b Supply, Installation, Testing and Commissioning of Lithium Ion Battery Bank of LFP Type 50AH-

30.72KWH-LITHIUM ION BATTERY CABINET (12Modules) Battery Bank for BOL 32min & EOL

25Mins backup with each UPS @ 60KVA/54KW Load condition.

Integrated Battery Management System with each battery cabinet for cell level, module level

and rack level monitoring complete with 5 years warranty

c Supply, Installation, Testing and Commissiong of Hot-swappable Modular Type 50KVA

Modular UPS with 125KVA Cabinet & 2Nos of 25KVA Module + 1No of 25KVA redundant

Module ) 3PH/3PH True Online Double Conversion UPS

b) KEOR MOD Switch Panel-IP,OP & BY

c) MODBUS for BMS integration

d) Inbuilt Manual Bypass Switch

e) DC Cable from UPS to Battery Bank ( 10m)

f) Phase sequence correction & protection

g) Battery breaker with the battery cabinet, complete with 5 years warranty

Supply, Installation, Testing and Commissioning of Lithium Ion Battery Bank of LFP Type 50AH-

30.72KWH-LITHIUM ION BATTERY CABINET (12Modules) Battery Bank for BOL 44min & EOL

34Mins backup with each UPS @ 40KVA/40KW Load condition. Nos. 2 1690029.04 33,80,058.08

Integrated Battery Management System with each battery cabinet for cell level, module level

and rack level monitoring complete with 5 years warranty

Total of Electrical items 3,42,74,066.00 1,84,70,966.78

Amount after GST Multiplication factor on DSR Items @1.0633 3,64,43,614.38 1,84,70,966.78

14 Digitally signed by

PRADYUMNA MUKHERJEE

SCHEDULE OF QUANTITIES - HVAC WORKS

DSR HVAC TOTAL

S No 2019/DSR DESCRIPTION UNIT QUANTITY RATE AMOUNT

EM 2018 DSR (INR) NON-DSR (INR)

Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/Variable

Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all hermetically

sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules,

microprocessor based Controller, top discharge type condensing unit(s), with R 410 A Refrigerant,

vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated

1 1.0 capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall per HP 216 16415.00 3545640.00

be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with first

charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less

than 3.1 and IEER not less than 6.5.

Supply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF

Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan

section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper

coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation,

2 2 cord less remote control etc., suitable for operation on

single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The unit shall have automatic force

shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor

unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature.

Supply, installation, testing and commissioning of following minimum capacity VRV/VRF High wall type

Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically

balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, outer

cabinet, cord less remote control, drain pan, necessary accessories etc., suitable for operation on 230 V

3 3.0 ± 10%, 50 Hz, single phase AC supply, complete as required. The unit shall have automatic force shut

down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit

will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature.

Supply, installation, testing and commissioning of following minimum capacity ONE-WAY flow

VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter,

fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX

Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration

isolation, cord less remote control etc., suitable for operation on

4 MR single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The unit shall have automatic force

shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor

unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature.

Lifting, Shifting, Supply, Installation, Testing & Commissioning of Interconnecting "Y" & "T" Joints i.e.

Refnet Joints/ Header with Insulation for refrigearnt piping

Refrigerant Piping

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of

following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with

5 5 fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories,

insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber

tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all

accessories as per specifications etc. as required:

5.1 5.1 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 312 245.00 76440.00

5.2 5.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 1520 331.00 503120.00

5.3 5.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 312 466.00 145392.00

5.4 5.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 1520 588.00 893760.00

5.5 5.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 500 707.00 353500.00

5.6 5.6 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 500 865.00 432500.00

5.7 5.7 25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 300 1022.00 306600.00

5.8 5.8 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation m 300 1108.00 332400.00

5.9 5.9 31.8 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation m 300 1170.00 351000.00

5.10 5.10 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation m 300 1230.00 369000.00

5.11 5.11 38.1 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation m 100 1265.00 126500.00

5.12 5.12 41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation m 100 1309.00 130900.00

6 1.14 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated

copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

Supply,installation,testing and commissioning of PVC drain water with necessary clamps, fittings such

as bends tees etc. and duly insulated.

40 mm dia (9 mm thick insulation) Rm 2340 400.00 936000.00

Total HVAC WORKS 11273490.00 1850562.00

Amount after GST Multiplication factor on DSR Items @1.0633 1,19,87,101.92 15

Digitally signed by

PRADYUMNA MUKHERJEE

SCHEDULE OF QUANTITIES - HVAC WORKS

S NO DESCRIPTION UNIT QUANTITY RATE DSR AMOUNT Non DSR AMOUNT

VAV BOX (WITH INTEGRAL SOUND ATTENUATOR)

Supply and Installation of pressure independent rectangular VAV unit with integral sound attenuator made of

22G GI sheet casing length 900mm consisting of 25mm thick 48kg/m3 density fiber glass wool covered with

tissue paper ,elliptical volume control damper , calibrated differential pressure sensor (DPT sensors) at inlet

complete with digital Thermostat.(All VAV shall be factory calibrated).

Supply, installation, testing and commissioning of Variable Frequency Drive (VFD)

MR 380-400 VAC, IP-54 Chassis, RFI class A1 (C2), No brake chopper.

a VFD upto 35 HP or as directed by the engineer in charge Nos. 6 192558.00 1155348.00

DUCT PRESSURE SENSORS

Supply, Installation and Testing of pressure sensors to be installed in supply air ducts. Quoted price shall

3.0 MR be inclusive of necessary conduting, copper control cabling from the sensors to the respective VFDs as per Nos. 24 18721.00 449304.00

"Approved Shop Drawings".

Supply, Installation, Testing & Commissioning of Silent type circular /rectangular inline fans for exhaust air

complete with sheet metal casing, 25mm thick acoustic insulation, direct driven centrifugal fan, motor with

proper protection and inspection door. Fan shall be suitable for operation on 220+6 % volts, 50 Hz,1 phase

AC power supply. Flanges to be provided on both sides to facilitate duct connections. Fan shall be installed

4.0 as shown in the drawings and will be of following characteristics:

MR All single phase inline fans shall be provided with factory fitted speed regulators. All Fans Should be complete

with Plug Top & necessary power cable.

Fans shall have low noise level in rage of 35-40dBA @3m and shall be suitable for indoor installations.

a 200 CFM S P of 13-14 for Toilet Nos. 9 6899.00 62091.00

b 500 CFM S P of 13-14 for Kitchen/ Pantry Nos. 2 10163.00 20326.00

5.0 Tube Axial Fan

Supply Installation, testing and commissioning of supply air Tube Axial flow fan of following capacity with

GSS casing and aluminium alloy impellers with high efficiency aero-foil sections, blades, the impeller directly

driven by TEFC induction motor suitable for 3 Phase 50 Hz 415 V ± 10 %, complete as required. This cost

a MR shall include the cost for suitable panel, DOL starter, breakers etc compete in all respect as per the directions

of engineer in charge.

9000 cfm at 15 mm static presuure for fresh air/exhaust air With Class "H" insulation. NOS 18 153950.00 2771100.00

Supplying, Fixing, testing and commissioning of fire dampers in supply air duct/main branch and return air path

as and where required of required sizes i/c control wiring,the damper shall be motorized and spring return so

as to close the damper in the event of power failure automatically and open the same in case of power being

6.0 16.20 restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall

also be closed in the event of fire signal complete as required and as per specifications.

(Fire damper shall ve suitable for 120 minutes fore rating as per NBC norms)

GI Gravity Louver

7.0 MR Supply, installation, testing and commissioning of GI Gravity Louver complete with neoperene rubber

gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications.

8.0 VOLUME CONTROL DAMPER

MR Supply, Installation and Testing of GI box type volume control dampers as per the specifications and shop

- For Rectangular Ducts

Supply, Installation, Testing and Commisioning of powder coated GI sheet metal factory fabricated flat oval

ducting with fittings and gripple wire supports. The factor of gripple support to suit the duct weight with

necessary anchor fastners and hook arrangements with suitable thickness etc., confirming to SMACNA

standards. Duct should be fabricated by using CNC machines including neccesary civil works as per site

9.0 condition. The joints shall be seamless and ducts joining shall be done using rivets only. The ducts shall be

powder coated with RAL color as per architect approval. The complete ducting cost shall be including 9 mm

MR thick nitrile rubber thermal with insulation internally. The insulation used for factory lining shall be of self

a Thickness 0.63 mm sheet SQM 2100 1720.00 3612000.00

b Thickness 0.80 mm sheet SQM 1200 2023.00 2427600.00

c Thickness 1.00 mm sheet SQM 300 2340.00 702000.00

d Thickness 1.25 mm sheet SQM 150 2900.00 435000.00

Diffusers & Grills

Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control

dampers as per specifications.

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume

control dampers complete as required

Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with aluminium

volume control dampers with anti smudge ring & removable core.

Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium without volume

control dampers with anti smudge ring & removable core.

Supply, Installation, Testing of 125mm deep antivibration flexible joints at the outlet of air handling

14.0 MR units/ductable split units//inline fans. Flexible connections shall be constructed using imported fire retardant RM 300 1540.00 462000.00

fabric with extruded aluminium frame/flange on both sides of approved make.

Supply, Installation, Testing and Balancing of linear slot diffusers as per the approved shop drawings and

specifications. Each slot shall be 25mm wide. The diffuser face shall be a one piece extrusion so there are no

visible joints. Slot diffusers shall be complete with end caps either as end plates or end angles or integral part,

air control blades etc. Slot diffuser have a variable neck length and the diffuser face could be optionally be

15.0 MR fitted to the plenum box on site. Diffuser shall have provision to access collar dampers for air balancing.

All Return air diffusers in false ceiling to be properly supported from real slab using chains or gripple wires.

3 slot/2slot, powder coated extruded aluminium diffusers of approved colour & shade. SQM 30 13372.00 401160.00

Supply, Installation and Testing of Bird Screens with GI wire mesh to be installed at the suction of fresh

16.0 MR air/discharge of Exhaust air as per the specifications and shop drawings. Sample of bird screen to be got SQM 30 5815.00 174450.00

approved from consultants and Clients prior to procurement.

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber

(Class "O") insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be

17.0 sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per

specifications and as required.

Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool

having density of 32 kg/m³, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600 mm centre to centre

18.0 16.21 covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet fixed to inside SQM 10 708.00 7080.00

surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as required and

as per specifications

Supply, Installation, Testing and Commissioning of Air Purification systems in the specified areas where

AHU/VRF/FCU/Cassette/Hi-Wall/Ductable units etc are installed, so as to improve indoor air quality by using,

Self-cleaning Needlepoint Ionizer made of Carbon brush emitters. The Needlepoint brushes shall be designed

to properly release equal amount of positive and negative ions in the supply air,>400Million ions/cc without any

obstruction. The units to be suitable for capacities up to 6000 CFM, with universal voltage input 24V to 240V

19.0 AC/DC, ionizer indicator LED, set of dry contacts which will indicate ionizer functionality. The unit shall have

MR capability to be switched on 24/7 and shall have weathertight conduit of minimum 6ft length.System should kill

microorganisms and pathogens and backed with Independent lab test reports on the real virus and not

surrogate. The system also should reduce odors, TVOC’s and reduce particle/particulate matter/PM2.5/PM10.

The products should be UL 2998 listed with zero Ozone Emission.

Smart Indoor Air quality monitor to measure Air quality parameters including AQI, PM1, PM2.5, PM10, CO2,

Humidity and Temperature. In addition to the mentioned sensors of the base device, you can customize it to

measure more parameters by adding extra sensors. This monitor should be a 3-tier architecture including

sensor Hardware, secure cloud infrastructure, monitoring apps including dashboard, android/IOS apps, where

20.0 MR ever requires. Dashboard should be customisable and IOT (Internet of things) enabled with view and

management for all of your locations on one dashboard so that you can easily identify and address any air

quality issues. Sensors should be soft calibratable. The System should be capable of providing periodic

Preventive maintenance for automated after sales support service in form of notification/ alerts and user

interaction through dashboard application.

Air Quality Monitor Nos 3 8109.00 24327.00

Supply, installation testing and commissioning of Router / Supervisory Controller which will manage the VAV

information and communicates on BACnet®/ LONWORKS® protocol to monitor and Control the VAVs from

BMS software on PC in accordance with the approved shop drawings and technical specifications. Connecting

the final daisy loop from all VAV to Supervisory Controller shall be part of the scope. The communication

21.0 MR between Supervisory controller and BMS software in PC should be on IP. Cost include powder coated Panel Nos 3 234202.00 702606.00

for Supervisory Controller of required size with 24 Volts provision which includes power cable, plug,

transformer and with all necessary accessories for mounting on wall in accordance with the approved shop

drawings and technical specifications.

Supply, Laying, Termination of ISI Certified 2 Core 1.0 sq.mm ATSC, FRLS,PVC insulated, Unarmored,

22.0 MR Tinned Copper, twisted, shielded, PE insulated, VAV Communication Cable with proper ferrules, lugs and Rmt 1500 129.00 193500.00

other necessary accessories. The spec shall meet the system manufacturer specifications.

Supply, Laying, Termination of ISI Certified 4 Core 1.0 sq.mm ATSC, FRLS ,PVC insulated, Unarmored,

23.0 MR Tinned Copper, twisted, shielded, PE insulated, VAV Communication Cable with proper ferrules, lugs and Rmt 1200 299.00 358800.00

other necessary accessories. The spec shall meet the system manufacturer specifications.

Supply & Laying of ISI Certified 1" dia PVC Conduit with bends, collar, saddles, saddle base and other

accessories for Signal Cable / DDC Communication Cable

TOTAL HVAC WORKS 3509972.00 20201733.00

Amount after GST Multiplication factor on DSR Items @1.0633 37,32,153.23 2,02,01,733.00

Digitally signed by

PRADYUMNA MUKHERJEE

SCHEDULE OF QUANTITIES: LIGHTING

S.No. Area Item Description Design Reference Unit UOM RATE NDSR AMOUNT NDSR AMOUNT

Design, manufacture, supply, installation, and commissioning of a Non Dimmable customized plain translucent ceiling-mounted light box not smaller

than 3700 x 1500 mm, unless approved otherwise by the architect. Sketch Lighting make Illuminated Ceiling system or equivalent from any

approved makes, matching below specifications. The wooden light box will be installed by the GC as per the architectural requirements and must meet

the following technical specifications. The light box will be ceiling-mounted, sized as approved by the architect. The light box should have a uniform

depth of 250 mm, with its bottom edge positioned 70-100 mm lower than the gypsum ceiling level.

Structure: The side walls of the light box will be constructed by the GC as per the recommendations of the lighting vendor. Light box should be made

from 18 mm thick moisture and termite-resistant plywood or HDDMR (High-Density High-Moisture Resistant Board), as approved by the architect. The

roof of the light box shall also be made of the same moisture and termite-resistant plywood or HDDMR board.

The outer surface, inner white paint and edges of the light box shall be finished as per the architect's recommendations and will be the responsibility of

the General Contractor (GC).

Interior Finish: The inner side of the light box shall be primed and painted in matte white for even light reflection. The light box must be fabricated on-site

to fit the exact dimensions and compatibility with the site.

Thermal Management: Before installing the LED light engine, the interior of the light box must be equipped with Thermal Interface Material for optimal

heat dissipation. Thermally conductive metal sheets should be securely attached to the interior roof of the wooden box to enhance heat dissipation

Meeting Rooms further. No's 4 ₹ 1,18,601.00 ₹ 4,74,404.00

LED Light Engine (10-15 watts/Sq Ft): The light engine must be Electronically Driven, Non Dimmable (but capable for dimming with just changing the

Driver, if required in future) ,. The color temperature (CCT) shall be customizable, offering the client four options to choose one from: 3000K, 4000K,

5700K and 6500K. The input voltage for the light engine must be 24V and should have a protection rating of IP20. All LED ,s should be installed outside

of the light box, in an easily accessible location for maintenance purposes.

Diffuser: A jointless translucent diffuser made from polyester knitted fabric coated with polyurethane (PU) must be installed inside the light box,

approximately 20-30 mm up from the bottom edge of the structure. The remaining 20-30 mm exposed surface outside the diffuser should be finished to

match the color of the light box’s outer surface and edges. The diffuser fabric should be: Heavy-duty, with a minimum weight of 200 gm/m² and a

minimum thickness of 0.3 mm. Matte, smooth, and uniform in appearance to reduce glare and provide a soft ambient glow even at higher lux levels. It

should have a light transmission efficiency of 50-60%, ensuring low-glare, soothing ambient lighting. The diffuser must meet the following technical

specifications: Tear strength: CH: 4.5 daN; TR: 6.5 daN Fire rating: B-S1, d0 Humidity-resistant and free from harmful CMR (Carcinogenic, Mutagenic,

Reprotoxic) substances and VOC (Volatile Organic Compounds).

Installation Requirements

Mounting and Integration: The light box will be securely mounted to the ceiling, maintaining the required depth and alignment. All wood work related

labor, wood, mounting hardware, fasteners, and accessories must be arranged and installed by the GC.

SITC of Elegant Electronically Driven, Non Dimmable (but capable for dimming with just changing the Driver, if required in future) LED profile systems

with small aperture, only 30-35mm. Modular continuous systems configured to obtain bespoke solutions by incorporating Darklighter Blade modules

from Sketch Lighting or any approved make. Power input: 36 - 40 W per meter of light module. Luminaire efficacy: Up to 60lm/W. Source: LED. Optics:

Diffused + Dark Louvers. Material: Profile: Extruded aluminum, Body and end caps: metal, Cover plate: Thermoplastic, Baffles and reflector:

Thermoplastic, Wall washer diffuser: PS or acrylic. Mounting: Recessed trim installation (with flange) using included brackets for drywall, wood or other

rigid ceiling panels. Maximum Height of Profile to be 50 mm. Custom linear lengths to be made available on request. Electrical: Integral high efficiency

LED Electronically Driven, Non Dimmable (but capable for dimming with just changing the Driver, if required in future) , for Electronically Driven, Non

Dimmable (but capable for dimming with just changing the Driver, if required in future) compatibility. Approx Length of 2400 mm

SITC of Electronically Driven, Non Dimmable (but capable for dimming with just changing the Driver, if required in future) Slim Hexagon Shaped UP-

DOWN Lighting with the feature of Interconnectivity to form the desired shape and get both direct and indirect lighting. Light part made of the slim

round shape of Dia between 15-25 mm (with 12-15 watts per mtr low voltage light engine) & slim connectors molded in ABS or Aluminium for a neat

finish. The system should ensure a seamless cascading design using uniform dimensions and materials for lighting up the space elegantly, eliminating

aesthetic inconsistencies, and light leakages. NOTE: Surface finish COLOR options SHOULD BE MADE AVAILABLE IF REQUESTED BY THE ARCHITECT.

Similar to Sketch Lighting make Hexawings customized Pendant or equivalent from approved brands.

Breakout Zone Diameter of Hexagon shape: 600 mm. Each set is to have 3 Hexagons joined together as one Pc. Set 1 ₹ 69,200.00 ₹ 69,200.00

Light Source Profile: 15-25 mm Round Shape

Frame: Aluminium ensuring good heat dissipation for the light engine.

Connectors: ABS or Aluminium

High-efficiency electronic Light Engine utilizing LEDs with > 100 lumens per watt with each hexagon of approx 40-50 watts.

Suspension system as per site requirements.

Frosted Diffuser

17 Digitally signed by

PRADYUMNA MUKHERJEE

SITC of Electronically Driven, Non Dimmable (but capable for dimming with just changing the Driver, if required in future) Linear Acoustic + Light 30

watts/mtr as an integrated solution that combines high-performance lighting with effective acoustic control. The system should ensure a seamless

design using uniform dimensions and materials for lighting and acoustic elements, eliminating aesthetic inconsistencies. . NOTE: DEPARTMENT-WISE

ACOUSTIC COLOR CODING TO BE PROVIDED, IF REQUESTED. Similar to Luxxbox make Axis 2 or Sketch Lighting make Decibel Linear Pendant or

equivalent from approved brands.

Dimensions: approx

Length: 4 Ft, Height: >100 mm

Workstations Width: 30-40 mm. No's 65 ₹ 11,300.00 ₹ 7,34,500.00

Lighting Element: Made of extruded aluminum, ensuring lightweight and high heat dissipation for the light engine.

Acoustic Element: Constructed from PET panels of shade as approved by the Architect, specifically tailored to the site requirements as per architect

approval, providing excellent sound absorption and lighting.

High-Efficiency Electronic Light Engine utilizing LEDs with > 140 lumens per watt

Suspension system as per site requirements.

Diffuser / Dark Louvers as approved by the architect.

SITC of Non Dimmable (but capable for dimming with just changing the Driver, if required in future) Linear Light 24-30 watts per mtr as an integrated

solution that combines high-performance lighting with Dead Matte Black Body Color. The body color needs to be Dead Matte Black. The light should

be jointless 4ft long to ensure a seamless design that eliminates aesthetic inconsistencies or light leakages. The suspension system & electrical wire

needs to be all-black in color. CCT - 3000 or 4000 or 5700 Kelvinas per architect recommendations. Sketch Lighting make SL5070 Prismatic Linear or

equivalent from approved makes

Length: 1200 mm approx

Small Width: 50 mm

Workstations Height - 70 mm

Light body: Made of extruded aluminum, ensuring lightweight and high heat dissipation for the light engine.

End Caps: Should be made of Metal or ABS.

High-Efficiency Non Dimmable (but capable for dimming with just changing the Driver, if required in future) Light Engine utilizing LEDs with >120

lumen per watt.

Suspension system lengths as per site requirements.

Prismatic Diffuser mandatory.

SITC of Electronically Driven, Non Dimmable (but capable for dimming with just changing the Driver, if required in future) Designer Formation of Light

with options for both UP and Downward light 1200x900 mm with minimum 50 watts 12-24 volt light engine. The body color needs to be Dead Matte

Black. LED ,s should be kept in the ceiling. CCT - 3000 or 4000 or 5700 Kelvin, as per architect recommendations. Sketch Lighting make NEST

FORMATION or equivalent from approved makes.

Length: 1200 mm

Rooms Light Profile: 15-25 mm Dia

Light Housing: Aluminium Light Sticks

End Caps & Connectors - To be made of powder-coated MS/SS.

High-efficiency , Electronic LED Light Engine utilizing LEDs with > 100 lumens per watt

Installation of this light should be done under the supervision of the lighting manufacturer team.

Frosted Diffuser.

SITC of Electronically Driven, Non Dimmable (but capable for dimming with just changing the Driver, if required in future) Conical Pendant Light 8

watts as an integrated design + light solution that combines high-performance lighting in soft conical shape with honeycomb light optics for glare

cutting. The light housing should have atleast 5 fins that act as heat hink for efficient heat dissipation and also acts as a design feature. The

suspension system & electrical wire needs to be all-black in color. LED , to be housed in separate ceiling canopy for longer life protecting the , and

COB from each other's dissipated heat. CRI - 97. CCT - 3000 or 4000 or 5700 Kelvin, as per architect recommendations. Sketch Lighting make Domo

Cone or equivalent from approved makes.

Light Housing Dimensions:

Cafeteria Side Dia: 60-90 mm with 36-40 degree beam angle.

Light body: Made of aluminum, ensuring lightweight and high heat dissipation for the light engine.

Powder coated in Matte Black color

High-efficiency , electronic Light Engine utilizing COBs with > 100 lumens per watt and Electronically Driven, Non Dimmable (but capable for dimming

with just changing the Driver, if required in future) ,

Suspension system lengths as per site requirements.

Optics - The Light source should not be visible from a distant viewing angle.

18 Digitally signed by

PRADYUMNA MUKHERJEE

SITC of Non Dimmable (but capable for dimming with just changing the Driver, if required in future) Designer Pendant Lights made of Scarpped

Corrugated Sheets as an initiative towards green planet. The light should have Electronic Driver , full glow LED Bulb of 5-8 Watts The light housing

should be of Globe shape being open from the bottom. The suspension system & electrical wire needs to be all-black or chrome in color. LED Driver

to be housed in separate ceiling canopy for longer life protecting the Driver and COB from each other's dissipated heat. CRI - 97. CCT - 3000 or 4000 or

5700 Kelvin, as per architect recommendations. Sketch Lighting make Scrappy Globe or equivalent from approved makes.

Light Housing Dimensions:

Cafeteria Main Dia: Mix of 200, 300 & 400 mm.

Light body: Made of Corrugated Paper with Dust repellent Clear Coat, ensuring lightweight and high heat dissipation for the Electronic Driver light

High-efficiency , electronic Light Engine utilizing COBs with > 100 lumens per watt and Electronic Driver Driver

Suspension system lengths as per site requirements.

Optics - The Light source should not be visible from a distant viewing angle.

SITC of Electronically Driven, Non Dimmable (but capable for dimming with just changing the Driver, if required in future) Linear Pendant Uplighter

taking inspiration from the render with 35-50 watts light engine as an integrated solution that combines high-performance uplighting with glare-free

design. Similar to Sketch Lighting make customized Wings or equivalent from approved makes or customized by any approved makes against approval

from the architect.

Length: 1200 mm approx

Sr. Executive Width: 30-40 mm. Height: In proportion to the design

Lighting Element: Made of Aluminium+MS+Acrylic, ensuring lightweight and easy heat dissipation for the light engine part.

Surface Finish: Finished in Matte Black.

High-Efficiency Electronically Driven, Non Dimmable (but capable for dimming with just changing the Driver, if required in future) Light Engine

utilizing LEDs with > 100 lumens per watt

Suspension system: as per site requirements.

Indirect Lighting for glaree free environment.

SITC of Non Dimmable (but capable for dimming with just changing the Driver, if required in future) Dome Pendant Light 15 watts as an integrated

solution that combines high-performance lighting with aesthetics. Similar to Sketch Lighting make Floral Dome Pendant or equivalent from approved

Reception & Light Source: Frosted Acrylic Vase with COB LED & Electronic Driver Driver inside the Canopy

Lighting Housing: Made of FRP & Light Engine with Heat Sink made in Aluminium ensuring lightweight and easy heat dissipation for the light engine.

Surface Finish: Finished in color as per architect's approval

High-Efficiency Electronic Driver Light Engine utilizing LEDs with > 100 lumens per watt and CRI >97

Suspension system: as per site requirements.

Dome should have Floral Pattern on the inner side.

SITC of customized Designer Light in Small Disc + Pipe Shape developed taking inspiration from the image. Length of the Light as approved by the

Architect. Aluminium Light Housing in Ring Shape of Dia 120-200 mm. Frosted Ring Light in Red Color with Electronic Driver Driver. The suspension

Reception Table Set 1 ₹ 99,875.00 ₹ 99,875.00

system should start as a thinner pipe and then a thicker pipe connecting to the suspension wire. CCT - 3000 or 4000 Kelvin as recommended by the

All Area with SITC of customized Electronic Driver , Linear Cove Light with Aluminium Housing and LED of 12w per Mtr. Sketch Lighting make COVE Light with

Cove heatsink profile and diffuser or equivalent from approved makes

SITC of customized Floor Lamp 5 watts as an integrated solution that combines high-performance lighting with aesthetics. Similar to shared image.

Height: 1600-1700 mm

Reception & Sr.

Executive Cabins Materials:

Lighting Housing: Made of MS & Aluminium ensuring lightweight and easy heat dissipation for the light engine.

Surface Finish: Finished in Black & Red

High-Efficiency: Light Engine utilizing LEDs with > 100 lumens per watt

Base should be heavy and sturdy enough to balance the floor lamp

Foot Switch mandatory.

19 Digitally signed by

PRADYUMNA MUKHERJEE

SITC of customized Electronic Driver , Linear Pendant Leather Light 40-50 watts with leather Design on the Surface, as an integrated solution that

combines high-performance lighting with bold aesthetic elements in metal and leather. The system should ensure a seamless design using uniform

dimensions and materials for lighting and designer elements, eliminating aesthetic inconsistencies. Similar to Sketch Lighting make Skin Linear XL or

equivalent from approved makes.

Length: 2000-2400 mm

CVO/Directors Width: 50-70 mm. Height: 100-150 mm No's 5 ₹ 1,06,000.00 ₹ 5,30,000.00

Lighting Element: Made of metal, ensuring lightweight and easy heat dissipation for the light engine.

Surface Finish: Finished in TAN Leather.

High-Efficiency Electronic Driver Light Engine utilizing LEDs with > 120 lumens per watt

Suspension system: Single Pipe Suspension System as per site requirements.

Prismatic / Frosted Diffuser

SITC of customized Table Lamp 5 watts as an integrated solution that combines high-performance lighting with aesthetics. Similar to shared image.

Height: 400-450 mm

CVO/Directors No's 5 ₹ 22,476.00 ₹ 1,12,380.00

Lighting Housing: Made of MS & Aluminium ensuring lightweight and easy heat dissipation for the light engine.

Surface Finish: Finished in Black & Red

High-Efficiency: Light Engine utilizing LEDs with > 100 lumens per watt

Base should be heavy and sturdy enough to balance the floor lamp

Foot Switch mandatory.

SITC of customized Linear Acoustic + Light as an integrated solution that combines high-performance lighting with effective acoustic control. The

system should ensure a seamless design using uniform dimensions and materials for lighting and acoustic elements, eliminating aesthetic

inconsistencies. Similar to Sketch Lighting make Decibel XL Linear Pendant or LuxxBox make Linear Acoustic Pendant 50 watts or equivalents from

approved brands.

Standard Length: 1500-1800 mm

Width: 400-500 mm. Height: 200-250 mm

CVO/Directors Fully customizable sizes to fit the architectural requirements of the site. No's 5 ₹ 81,420.00 ₹ 4,07,100.00

Lighting Element: Made of extruded aluminium, ensuring lightweight and high heat dissipation for the light engine.

Acoustic Element: Constructed from PET panels, specifically tailored to the site requirements and colors as per architect approval, providing excellent

sound absorption and acoustic management.

High-Efficiency Electronic Driver Light Engine utilizing LEDs with > 120 lumens per watt

Suspension system as per site requirements. Acoustic Color as per architects

Prismatic or Frosted Diffuser approval

SITC of Non Dimmable (but capable for dimming with just changing the Driver, if required in future) Designer Pendant Lamps made of Aluminium. 3-5

Watts COB with Electronic Driver Driver. Finish as per architects approval. Sketch Lighting make Spike Mini or equivalent from approved make. Single No's 5 ₹ 12,484.00 ₹ 62,420.00

Unit in each toilet

20 Digitally signed by

PRADYUMNA MUKHERJEE

SITC of Non Dimmable (but capable for dimming with just changing the Driver, if required in future) Slim Hexagon Shaped UP-DOWN Lighting with the

feature of Interconnectivity to form the desired shape and get both direct and indirect lighting. Light part made of the slim round shape of Dia

between 15-25 mm (with 12-15 watts per mtr low voltage light engine) & slim connectors molded in ABS or Aluminium for a neat finish. The system

should ensure a seamless cascading design using uniform dimensions and materials for lighting up the space elegantly, eliminating aesthetic

inconsistencies, and light leakages. NOTE: Surface finish COLOR options SHOULD BE MADE AVAILABLE IF REQUESTED BY THE ARCHITECT. Similar to

Sketch Lighting make Hexawings customized Pendant or equivalent from approved brands.

Breakout Zone Diameter of Hexagon shape: 600 mm. Each set is to have 3 Hexagons joined together as one Pc. Set 2 ₹ 67,200.00 ₹ 1,34,400.00

Light Source Profile: 15-25 mm Round Shape

Frame: Aluminium ensuring good heat dissipation for the light engine.

Connectors: ABS or Aluminium

High-efficiency electronic Light Engine utilizing LEDs with > 100 lumens per watt with each hexagon of approx 40-50 watts.

Suspension system as per site requirements.

Frosted Diffuser

SITC of customized Floor Lamp 5 watts as an integrated solution that combines high-performance lighting with aesthetics. Similar to shared image.

The shortlisted vendor must get the 3D render and drawings approved by the architect before production.

Height: 1600-1700 mm

Breakout Zone No's 2 ₹ 34,956.00 ₹ 69,912.00

Lighting Housing: Made of MS & Aluminium ensuring lightweight and easy heat dissipation for the light engine.

Surface Finish: Finished in Black & Red

High-Efficiency: Light Engine utilizing LEDs with > 100 lumens per watt

Base should be heavy and sturdy enough to balance the floor lamp

Foot Switch mandatory.

SITC of Non Dimmable (but capable for dimming with just changing the Driver, if required in future) Linear Loop Light with Soft Curves (30 watts per

mtr) + Tiltable Acoustic Disc as an integral part of the light (as per meeting table dimensions) as an integrated solution that combines high-

performance lighting with effective acoustic control. The system should ensure a seamless design using uniform dimensions and materials for lighting

and acoustic elements, eliminating aesthetic inconsistencies, and light leakages. NOTE: DEPARTMENT-WISE ACOUSTIC COLOR CODING SHOULD BE

MADE AVAILABLE IF REQUESTED BY THE ARCHITECT. Similar to Delta make Soliscape or Sketch Lighting make Biovista Pendant or equivalent from

approved brands.

Length: 3000 mm (With 2 Tiltable Acoustic Discs)

Meeting Rooms Closeup View No's 5 ₹ 1,38,500.00 ₹ 6,92,500.00

Width: 1000-1200 mm.

Frame: Fabricated in metal for sturdiness, while ensuring good heat dissipation for the light engine.

Acoustic Element: Constructed from PET panels that are slim on the edges and thicker in the center, specifically tailored to the site requirements and

colors as per architect approval, providing excellent sound absorption and light output.

High-Efficiency Electronic Light Engine utilizing LEDs with > 140 lumens per watt.

Suspension system as per site requirements.

Prismatic/Frosted Diffuser

SITC of Non Dimmable (but capable for dimming with just changing the Driver, if required in future) Twin Linear Light 12-15w per mtr in each profile

as an integrated solution that combines high-performance lighting with Square/Rectangular Design Element through which Profiles should penetrate.

The body color needs to be Dead Matte Black or White. The light should be jointless 4ft long to ensure a seamless design that eliminates aesthetic

inconsistencies or light leakages. The suspension system & electrical wire needs to be all-black in color. CCT - 3000 or 4000 or 5700 Kelvinas per

architect recommendations. Sketch Lighting make Linear Twin Rail or equivalent from approved makes. The shortlisted vendor must get the 3D

render and drawings approved by the architect before production.

Length: 1500 mm approx

Light body: Made of extruded aluminum, ensuring lightweight and high heat dissipation for the light engine.

End Caps: Should be made of Metal or ABS.

High-Efficiency Non Dimmable (but capable for dimming with just changing the Driver, if required in future) Light Engine utilizing LEDs with >120

lumen per watt.

Suspension system lengths as per site requirements.

Prismatic/Frosted Diffuser mandatory.

21 Digitally signed by

PRADYUMNA MUKHERJEE

SITC of Non Dimmable (but capable for dimming with just changing the Driver, if required in future) Linear Light 24-30 watts per mtr as an integrated

solution that combines high-performance lighting with Dead Matte Black Body Color. The body color needs to be Dead Matte Black. The light should

be jointless 4ft long to ensure a seamless design that eliminates aesthetic inconsistencies or light leakages. The suspension system & electrical wire

needs to be all-black in color. CCT - 3000 or 4000 or 5700 Kelvinas per architect recommendations. Sketch Lighting make SL5070 Prismatic Linear or

equivalent from approved makes

Executive Length: 1200 mm approx

Officers/PS Width: 50 mm No's 33 ₹ 4,993.00 ₹ 1,64,769.00

Rooms Height - 70 mm

Light body: Made of extruded aluminum, ensuring lightweight and high heat dissipation for the light engine.

End Caps: Should be made of Metal or ABS.

High-Efficiency Non Dimmable (but capable for dimming with just changing the Driver, if required in future) Light Engine utilizing LEDs with >120

lumen per watt.

Suspension system lengths as per site requirements.

SITC of customized Designer Light in Small Disc + Pipe Shape developed taking inspiration from the image. Length of the light as approved by the

architect. Aluminium Light Housing in Ring Shape of Dia 120-200 mm. Frosted Ring Light in Red Color with Electronic Driver Driver. The suspension

Reception Table Set 1 ₹ 1,00,800.00 ₹ 1,00,800.00

system should start as a thinner pipe and then a thicker pipe connecting to the suspension wire. CCT - 3000 or 4000 Kelvin as recommended by the

Architect. The shortlisted vendor must get the 3D render and drawings approved by the architect before production.

All Area with SITC of customized Electronic Driver , Linear Cove Light with Aluminium Housing and LED of 12w per Mtr. Sketch Lighting make COVE Light with

Cove heatsink profile and diffuser or equivalent from approved makes

SITC of Elegant Non Dimmable (but capable for dimming with just changing the Driver, if required in future) Pendant/Recessed Linear LED profile

systems with small aperture, only 30-35mm. Modular continuous systems configured to obtain bespoke solutions by incorporating Darklighter Blade

modules from Sketch Lighting or any approved make. Power input: 12 W to 40 W per module. Luminaire efficacy: Up to 60lm/W. Source: LED. Optics:

Downlight: Spot, flood, wide flood, general light pro, medium oval transversal or longitudinal and wide flood oval transversal or longitudinal options to be

made available as per site requirements. Material: Profile: Extruded aluminum, Body and end caps: metal, Cover plate: Thermoplastic, Baffles and

reflector: Thermoplastic, Wall washer diffuser: PS or acrylic. Mounting: Recessed trim installation (with flange) using included brackets for drywall, wood

or other rigid ceiling panels. Maximum Height of Profile to be 50 mm. Custom linear lengths to be made available on request. Electrical: Integral high

efficiency LED Electronic Driver driver for Electronic Driver compatibility. Size of the Blade Linear to be finalized as per the size of the ceiling wooden box

Auditorium SITC of Cove Light as per site requirements with Aluminium profile and Low voltage Drivers & Electronic Driver Controller Rmtrs 200 ₹ 3,550.00 ₹ 7,10,000.00

SITC of customized designer Non Dimmable (but capable for dimming with just changing the Driver, if required in future) pendant light made of

Rattan as per architects approval

Design, manufacture, supply, installation, and commissioning of a Electronically Driven, Non Dimmable (but capable for dimming with just changing the

Driver, if required in future) customized translucent ceiling-mounted fabric and light engine. Sketch Lighting make Illuminated Ceiling, or equivalent from

any approved makes, matching below specifications. from any approved makes The light box will be installed as per the architectural requirements and

must meet the following technical specifications. The light box will be ceiling-mounted, size as approved by the architect. The ceiling box should have a

uniform depth of 250 mm or as requested by the light manufacturer for spotless and glare-free illumination.

Structure: The side walls of the light box will be constructed by the GC as part of the ceiling. Wooden box which is not part of this item, should be made

from 18 mm thick moisture and termite-resistant plywood or HDDMR (High-Density High-Moisture Resistant Board), as approved by the architect. The

roof of the box shall also be made of the same moisture and termite-resistant plywood or HDDMR board.

Interior Finish: The inner side of the box shall be primed and painted in matte white for even light reflection and the white part should not be visible after

installation of the fabric.

Thermal Management: Before installing the LED light engine, the interior of the light box must be equipped with Thermal Interface Material for optimal

heat dissipation. Thermally conductive metal sheets should be securely attached to the interior roof of the wooden box to further enhance heat

22 Digitally signed by

PRADYUMNA MUKHERJEE

heat dissipation. Thermally conductive metal sheets should be securely attached to the interior roof of the wooden box to further enhance heat

LED Light Engine: The light engine must be low voltage ranging from 12- 24V. The color temperature (CCT) shall be customizable, offering the client

four options to choose one from: 3000K, 4000K, 5700K and 6500K. The lux level on the workplane should be minmum 1000 lux and it should be

compatible for dimming. The input voltage for the light engine must be 24V and should have a protection rating of IP20. All LED drivers should be

installed outside of the light box, in an easily accessible location for maintenance purposes.

Diffuser: A jointless translucent diffuser made from polyester knitted fabric coated with polyurethane (PU) must be installed inside the ceiling box,

approximately 20-30 mm up from the bottom edge of the structure. The remaining 20-30 mm exposed surface outside the diffuser should be finished to

match the color of the wooden ceiling surface and edges. The diffuser fabric should be: Heavy-duty, with a minimum weight of 200 gm/m² and a

minimum thickness of 0.3 mm. Matte, smooth, and uniform in appearance to reduce glare and provide a soft ambient glow even at higher lux levels. It

should have a light transmission efficiency of 50-60%, ensuring low-glare, soothing ambient lighting. The diffuser must meet the following technical

specifications: Tear strength: CH: 4.5 daN; TR: 6.5 daN Fire rating: B-S1, d0 Humidity-resistant and free from harmful CMR (Carcinogenic, Mutagenic,

Reprotoxic) substances and VOC (Volatile Organic Compounds).

Installation Requirements

Mounting and Integration: The light engine should be securely mounted to the ceiling wooden boxes, maintaining the required depth and alignment.

Wood work not included.

SITC of customized Designer Table Lamp with E27 - 15 watts LED developed taking inspiration from the image. Metal Base with Fabric Shade. E27

Frosted LED Lamp. Approx 480-500 mm Total Height of Table Lamp. Fabric Shade 300-350 mm Dia & 200-250 mm Height. The Body Color and Fabric

Color should be as recommended by the Architect. CCT - 2700-3000 Kelvin. The shortlisted vendor must get the 3D render and drawings approved by

the architect before production.

SITC of customized Designer Floor Lamp with E27 - 15 watts LED developed taking inspiration from the image. Metal Base with Fabric Shade. E27

Frosted LED Lamp. Approx 1200-1500 mm Total Height of Floor Lamp. Fabric Shade 300-450 mm Dia & proportionate Height, or any design selected by

the architect. The Body Color and Fabric Color should be as recommended by the Architect. CCT - 2700-3000 Kelvin. The shortlisted vendor must get

the 3D render and drawings approved by the architect before production.

Designing, manufacturing, supply, installing, and commissioning of a Non Dimmable customized lighting system inspired by Oil India pipelines, ensuring

functional, aesthetic, and technological integration with the following requirements: Similar to the concept designed by Sketch Lighting or from any

approved makes that matches below specifications.

Design Specifications

•Lighting Concept: The lighting system should emulate the appearance of a scaled-down version of an OIL INDIA pipeline, with miniature versions of

valves, flanges, nuts, and bolts resembling actual pipeline elements.

oThe decorative pipeline components (valves, flanges, nuts, bolts) shall be made of durable and lightweight materials such as ABS or carbon fiber for

both aesthetic and structural integrity.

oThe light housing will consist of approximately 30-50 mm diameter light pipes to create the visual effect of light flowing within the pipeline.

•Suspension System:

oThe lighting system shall be suspended from the ceiling using suitable methods such as suspension wires or slim pipes (up to 12 mm in diameter),

ensuring stability and proper alignment.

oThe manufacturer shall provide the most suitable suspension mechanism for the design.

oThe General Contractor shall make proper arrangements to hide LED drivers at a reachable location for ease of maintenance.

•Total Length: The total length of the artistic lighting design will be between 50 meters and 60 meters, covering the required area of the boardroom

23 Digitally signed by

PRADYUMNA MUKHERJEE

•Total Length: The total length of the artistic lighting design will be between 50 meters and 60 meters, covering the required area of the boardroom

Lighting Requirements

oHigh-efficiency, high-lumen output LEDs are required, with colour rendering and CCT suitable for a boardroom environment.

oThe lighting shall provide even and glare-free illumination suitable for video conferencing applications, utilizing advanced diffused optics to ensure

•Lighting Distribution: The system must offer uniform distribution of light, creating the effect of continuous light flow through the Light tube.

Automation and Control System

•Electronic Driver (Digital Addressable Lighting Interface):

oThe lighting system shall be fully Non Dimmable (but capable for dimming with just changing the Driver, if required in future), providing seamless

integration with Electronic Driver lighting automation systems.

oThe system must allow for precise control of lighting intensity, scheduling, and scenes to accommodate different boardroom functions (e.g.,

presentations, meetings, video conferencing).

Installation Requirements

•Mounting: The entire lighting system should be securely mounted, with attention to safety and aesthetics. The manufacturer shall be responsible for

providing all necessary mounting hardware and accessories.

•Wiring: All wiring for both power and Electronic Driver communication should be concealed and run through the suspension system or integrated into the

ceiling structure as per site conditions, ensuring a clean and unobtrusive installation.

•Power and Efficiency:

oThe lighting system must be energy-efficient, and designed to meet or exceed applicable energy conservation codes.

oThe light sources should have a minimum lifespan of 30,000 burning hours and should be easily replaceable without disassembling whole system.

Quality and Compliance

•Safety and Standards:

oThe light engine shall utilize only those LEDs and drivers that are BIS (Bureau of Indian Standards) certified.

oBeing designed and made to order, no separate certification is required for the complete customized designer light system.

•Warranty: The lighting system shall come with a warranty of 15 months from the date of invoice, covering both the LED light sources and control

Documentation and Testing

•Shop Drawings and Approvals: The manufacturer shall provide 3D Renders and material specifications, for the architect's approval if requested by the

oOn-site testing and commissioning will be required after installation to verify system functionality, light levels, and Electronic Driver control operations.

SITC of Non Dimmable (but capable for dimming with just changing the Driver, if required in future) Designer Pendant Lamps made of Aluminium. 3-5

CMD Toilet Watts COB with Electronic Driver Driver. Finish as per architects approval. Sketch Lighting make Spike Mini or equivalent from approved make. Set of No's 3 ₹ 37,500.00 ₹ 1,12,500.00

SITC of Designer Bamboo Bollard Lamps made of Aluminium + MS. 3-5 Watts COB with electronic Drivers concealed in Floor Base. Each suitably

CMD Terrace Ingress Protected Floor Lamp should have 3 Pipes & total of 5 mini spot lights throwing lights in different directions. The height of the sticks should be

Garden 1800-2000 mm (with 3 spots), 1200-1500 mm (with 2 spots), 600 mm (with single spot). To be customized by Sketch Lighting or any approved brand.

The shortlisted vendor must get the 3D render and drawings approved by the architect before production.

SITC of INGRESS PROTECTED Floor Cove Light as per site requirements with Aluminium profile and Low voltage IP 65-68 Drivers. Rmtrs 30 ₹ 5,428.00 ₹ 1,62,840.00

SITC of Designer Pendant Light made of Beaten Brass with Indirect light throw and light engine of 15 Watts with electronic Drivers Size: approx 600

Executive Waiting

mm Dia. Brass Sheet to be finished with a clear coat to protect from weathering. To be customized by any approved brand. The shortlisted vendor No's 5 ₹ 43,500.00 ₹ 2,17,500.00

must get the 3D render and drawings approved by the architect before production.

24 Digitally signed by

PRADYUMNA MUKHERJEE

Executive Waiting SITC of Cove Light as per site requirements with Aluminium profile and Low voltage Drivers & Electronic Driver Controller. Sketch Lighting make COVE

for CMD office Lighting with aluminium heat sink profile and diffuser, or equivalent from approved makes.

SITC of Cove Light as per site requirements with Aluminium profile and Low voltage Drivers & Electronic Driver Controller Rmtrs 200 ₹ 3,745.00 ₹ 7,49,000.00

SITC of Non Dimmable (but capable for dimming with just changing the Driver, if required in future) Designer Formation of Light with options for both

UP and Downward light 1200x900 mm with 30-50 watts light engine. The body color needs to be Dead Matte Black. LED Drivers should be kept in the

ceiling. CCT - 3000 or 4000 or 5700 Kelvin, as per architect recommendations. Sketch Lighting make NEST FORMATION or equivalent from approved

Length: 1200 mm

near Reception & No's 6 ₹ 68,664.00 ₹ 4,11,984.00

Dining Light Profile: 15-25 mm Dia

Light Housing: Aluminium Light Sticks

End Caps & Connectors - To be made of powder-coated MS/SS.

High-efficiency , Electronic LED Light Engine utilizing LEDs with > 100 lumens per watt

Installation of this light should be done under the supervision of the lighting manufacturer team.

Frosted Diffuser.

SITC of Non Dimmable (but capable for dimming by just changing the Driver, if required in future) Designer Pendant Light as rendered. The

customized designer feature should have the body color as per the architect's recommendations. LED Drivers should be kept in the ceiling canopy.

CCT - 3000 or 4000 Kelvin, as per architect recommendations. Similar to Sketch Lighting make Satin Pendant 450 mm with light source slightly inside

from the bottom of the light.

Executive Dining No's 12 ₹ 24,500.00 ₹ 2,94,000.00

Length of suspension - as per site

SITC of Non Dimmable (but capable for dimming with just changing the Driver, if required in future) Recessed 12-15 Watts Downlight with glare-free

black deflector and honeycomb mesh. CRI > 97. CCT - 3000 or 4000 or 5700 Kelvinas per architect recommendations. With Narrow <6mm Trim for a

neat look post installation. Sketch Lighting make Lavender Blade 12-15 watts or equivalent from approved makes.

Housing Dimensions:

Dia: 105-110 mm with 36-40 degree beam angle.

Executive Dining No's 1040 ₹ 2,247.00 ₹ 23,36,880.00

Height - <75 mm

Light Housing: Made of diecast aluminum, ensuring lightweight and high heat dissipation for the light engine.

Powder coated in Matte White color on the outside and Lip.

High-efficiency , , electronic Light Engine utilizing COBs with > 100 lumens per watt and Electronic Driver Driver Glare free soothing light

SITC of customized Designer Light made of Natural Rattan Material. Dia - 900-1200 mm Dia as per architects approval. Frosted Light Source with

Reception Electronic Driver Driver. The suspension system should be designed as per site requirements. CCT - 3000 or 4000 Kelvin or as as recommended by the No's 7 ₹ 72,000.00 ₹ 5,04,000.00

Architect. Sketch Lighting make customized Rattan Pendant Design or equivalent from approved makes

25 Digitally signed by

PRADYUMNA MUKHERJEE

SITC of Non Dimmable (but capable for dimming with just changing the Driver, if required in future) Designer Formation of Light with options for both

UP and Downward light 1200x900 mm with 30-50 watts light engine. The body color needs to be Dead Matte Black. LED Drivers should be kept in the

ceiling. CCT - 3000 or 4000 or 5700 Kelvin, as per architect recommendations. Sketch Lighting make NEST FORMATION or equivalent from approved

Length: 1200 mm

Light Profile: 15-25 mm Dia

Light Housing: Aluminium Light Sticks

End Caps & Connectors - To be made of powder-coated MS/SS.

High-efficiency , Electronic LED Light Engine utilizing LEDs with > 100 lumens per watt

Installation of this light should be done under the supervision of the lighting manufacturer team.

Frosted Diffuser.

All Area with SITC of customized Electronic Driver , Linear Cove Light with Aluminium Housing and LED of 12w per Mtr. Sketch Lighting make COVE Light with

Cove heatsink profile and diffuser or equivalent from approved makes

SITC of customized Table Lamp 5 watts as an integrated solution that combines high-performance lighting with aesthetics. Similar to shared image,

customized by any approved lighting brand. The shortlisted vendor must get the 3D render and drawings approved by the architect before

Reception & Height: 300-450 mm

Other VIP Areas

Lighting Housing: Made of MS & Light Ring in Aluminium ensuring lightweight and easy heat dissipation for the light engine.

Surface Finish: Finished in Black & Red

High-Efficiency: Light Engine utilizing LEDs with > 100 lumens per watt

Base should be heavy and sturdy enough to balance the table lamp

Hand Off ON Switch mandatory.

26 Digitally signed by

PRADYUMNA MUKHERJEE

SCHEDULE OF QUANTITIES: OCCUPANCY SENSORS AND CUR

S No Line Items Image

Sensor Mounting

FOR ALL CURTAIN

AUTOMATION WORK,

6 ARCHITECT'S APPROVAL ON

QTY'S & ITEMS MANDATORY

BEFORE PURCHASING

CHEDULE OF QUANTITIES: OCCUPANCY SENSORS AND CURTAIN REMOTE CONTROLS

Description Unit QTY

SITC of ceiling-mounted PIR-triggered switch designed for presence or absence detection,

capable of controlling lighting and non-lighting loads based on occupancy and illuminance.

Helvar VS make SF-PIR-SW-01 vs or similar model from approved makes matching the

below specifications.

Functional Requirements

Presence: Auto on/off based on occupancy.

Absence: Manual on, auto off.

Illuminance threshold: 10 lx to 1000 lx.

Time delay: 10 seconds to 40 minutes.

Selectable presence/absence detection.

Automatic load control and energy-saving operation. Nos 100

Simple installation and multiple sensor compatibility.

Operational Specifications

Presence Mode: Auto switches load on when occupied and off after the set time.

Absence Mode: Manual on via a retractive switch; auto off based on time-out or switch

Installation & Technical Requirements

Ceiling-mountable.

Works with mains-rated retractive wall switches.

Multiple units can extend detection zones.

Documentation & Warranty

Provide manuals, datasheets, and wiring diagrams.

1-year warranty from installation date.

Acceptance Criteria

Functional as specified with adjustable settings.

Flexible configuration for various occupancy styles.

Sensor Mounting & Accessories: Supporting PVC box For Sensors In Open Celling

Motor Specification : SOMFY make LSN 4/28 RTS Motor or any model matching

the specifications from the approved makes. Required for the approved size of

Blinds as per project specific requirements with Open/Close/Stop operation of

Blinds from radio frequency , will fix on wooden pelmet/ceiling/walls. Somfy Blinds

Motor having voltage range of 230V – Nominal Torque (nm) 4nm,RPM 28 ,

Adjustable Limits,Blind Maximum Weight capacity 10kg ,it will cover upto 100 Sqft

Fabric Area ,diameter of the motor 40 mm, Maximum length: 562mm (1) Tube size:

40 mm (2) Rated power:150 W (3) Rated current: 0.65 A (4) IP Rating : IP44 (5)

Thermal cutoff: 4 Minutes (6) Motor stop limit: Electronic (7) RF frequency: 433.42

Mhz. (8) Noise Level 50Dba (9)Working Temp Range 0ºC to +60ºC recommended

by the manufacturer for suitable above motor & warranty of the motors should be 5

years. One Motor can cover upto 100 Sqft Fabric.

Somfy make STD aluminium tube with Related accessories for the 40 Dia Motor, or

equivalent from approved maked

Somfy make Telis 16 RTS Pure Keypad for Blind, or Equivalent from approved

makes (One Remote for 15 Motors) Nos 5

Supply, Installation, Testing & Commissioning of Motorised Shades System Nos 10

SCHEDULE OF QUANTITIES: IT-ACTIVE & PASSIVE, WI-FI & EPBAX WORKS AT DATA CENTRE

S NO DESCRIPTION QUANTITY UNIT RATE DSR AMOUNT NDSR AMOUNT

Supply Installation Testing & Commissioning of Cat6A AUTP 24 AWG Patch Cord Patch cord (2 mtr.): 6A UTP Patch Cords are Factory Tested for Better Quality and

Suitable for the High Speed Data Transmission. Complies to the Standard ANSI/TIA/EIA-568-C.2 Standard. Supports Data Networks Speeds Up to 10/100- Base-T and

1000-Base-T. Available In LSZH Jacket-Reduced Toxic Gasses Emitted During Combustion , RJ45, 8P8C, 3 Prong Design for accurate termination, 50µ" Gold Plated

Contacts , Insulation Thickness 0.16mm, 100% Factory Tested , Transparent Boot Cable Assemblies.ETL Verified 4 connector channel performance with MTPL up to 635

1 MR MHz, and registered under a ETL Followup Program. Complaint to RoHS Directive 2011/65/EU and (EU) 2015/863. OEM should have ISO 9001:2015, ISO 14001:2015, Sets 900 375.00 0.00 3,37,500.00

ISO 45001:2018 and and should have a certified PMP, CDCP and ITIL on the OEM’s payroll sitting in India whose services can be utilized for this project for Data as per

given Specification etc. all complete

Supply Installation Testing & Commissioning of Cat6A UTP 24 AWG Patch Cord Patch cord (1 mtr.): 6 UTP Patch Cords are Factory Tested for Better Quality and

Suitable for the High Speed Data Transmission. Complies to the Standard ANSI/TIA/EIA-568-C.2 Standard. Supports Data Networks Speeds Up to 10/100- Base-T and

1000-Base-T. Available In LSZH Jacket-Reduced Toxic Gasses Emitted During Combustion , RJ45, 8P8C, 3 Prong Design for accurate termination, 50µ" Gold Plated

Contacts , Insulation Thickness 0.16mm, 100% Factory Tested , Transparent Boot Cable Assemblies.ETL Verified 4 connector channel performance with MTPL up to 635

2 MR MHz, and registered under a ETL Followup Program. Complaint to RoHS Directive 2011/65/EU and (EU) 2015/863. OEM should have ISO 9001:2015, ISO 14001:2015, Sets 900 300.00 0.00 2,70,000.00

ISO 45001:2018 and and should have a certified PMP, CDCP and ITIL on the OEM’s payroll sitting in India whose services can be utilized for this project for Data Jack

Panel end as per given Specification etc. all complete

Supply, Installation, Testing and Commissioning of loaded Patch Panel 24 Port Cat 6A U/UTP ,The Cat-6A transmission performance is in compliance and Exceeds

ANSI/TIA/EIA-568.2-D Standard. Supports 1000-Base-T. 90 Degree (Top Entry) or 180 Degree Punch Down Design for Convenient Network Terminations, Individual

replaceable jack module panel design as applicable.UL Listed, Complaint to RoHS Directive 2011/65/EU and (EU) 2015/863 and ASTM B 117 Certified. OEM should

3 MR have ISO 9001:2015, ISO 14001:2015and ISO 45001:2018 or latest. All networking passive material (Fiber Cable, Copper Cables, Networking Racks and their No's 35 12,500.00 0.00 4,37,500.00

connectivity components) should be from one OEM make only for Data as per given Specification etc. all complete

Supply Installation Testing & Commissioning of Cat6A UTP 24 AWG Patch Cord Patch cord (1 mtr.): 6 UTP Patch Cords are Factory Tested for Better Quality and

Suitable for the High Speed Data Transmission. Complies to the Standard ANSI/TIA/EIA-568-C.2 Standard. Supports Data Networks Speeds Up to 10/100- Base-T and

1000-Base-T. Available In LSZH Jacket-Reduced Toxic Gasses Emitted During Combustion , RJ45, 8P8C, 3 Prong Design for accurate termination, 50µ" Gold Plated

Contacts , Insulation Thickness 0.16mm, 100% Factory Tested , Transparent Boot Cable Assemblies.ETL Verified 4 connector channel performance with MTPL up to 635

4 MR MHz, and registered under a ETL Followup Program. Complaint to RoHS Directive 2011/65/EU and (EU) 2015/863. OEM should have ISO 9001:2015, ISO 14001:2015, Sets 340 300.00 0.00 1,02,000.00

ISO 45001:2018 and and should have a certified PMP®, CDCP and ITIL on the OEM’s payroll sitting in India whose services can be utilized for this project for Voice Jack

Panel end as per given Specification etc. all complete

Supply, Installation, Testing and Commissioning of loaded Patch Panel 24 Port Cat 6A U/UTP ,The Cat-6 transmission performance Should compliance and Exceeds

ANSI/TIA/EIA-568.2-D Standard. Supports 1000-Base-T. 90 Degree (Top Entry) or 180 Degree Punch Down Design for Convenient Network Terminations, Individual

replaceable jack module panel design as applicable.UL Listed, Complaint to RoHS Directive 2011/65/EU and (EU) 2015/863 and ASTM B 117 Certified. OEM should

5 MR have ISO 9001:2015, ISO 14001:2015and ISO 45001:2018 or latest.All networking passive material (Fiber Cable, Copper Cables, Networking Racks and their No's 15 12,500.00 0.00 1,87,500.00

connectivity components) should be from one OEM make only for Voice Field as per given Specification etc. all complete

6 MR Supply Installation Testing & Commissioning of 1 U PVC Cable Manager as per given Specification etc. No's 65 700.00 0.00 45,500.00

Supply Installation Testing & Commissioning of Mounting Hardware pack of 10pcs as per given Specification etc. all complete.

Supply Installation Testing & Commissioning of 24 U 800mmX800mm Closed Network Rack with standard accessories as per given Specification etc. all

Supply Installation Testing & Commissioning of 42 U 800mmX800mm Closed Network Rack with standard accessories as per given Specification etc. all

Supply, Installation, Testing and Commissioning of Information Outlet Set(I/0) : Quard Face Plate Square (86 x 86mm) x 12 mm Shutter on Face Plate Two Piece design :

Mounting Frame and Cover Plate Should support UTP and STP Jacks Cat5e, Cat6 and Cat6A Plug Reliability : 750 Cycles minimum Cover Material : ABS UL94-V0 Base

Material : ABS- UL94-V0 Dust Cover Material : ABS-UL94-V0 ,Should have Robust and installer friendly design Surface Mount Boxes for Face Plates for a variety of

10 MR media including voice and data, Audio, video and CATV distribution to the work area. Material : ABS, Shape : Square Size : 86 x 86 , White colour. Complaint to RoHS No's 900 200.00 0.00 1,80,000.00

Directive 2011/65/EU and (EU) 2015/863. OEM should have ISO 9001:2015, ISO 14001:2015, ISO 45001:2018 and should be present in India for at-least 10 years or

Supply,lnstallation,Testing & Commissioning of 4 pair Cat6A U/UTP Cable in the existing surface/ recessed steel/ PVC conduit as required: The 4 pair Unshielded Twisted

Pair cable shall be UL Listed,exceeds the requirements of ANSI/TIA-568- C.2 and ISO/IEC 11801 Class E, 4 twisted pairs separated by internal HDPE Cross Separator.

Full separator. Half shall not be accepted. Rip Cord is must,lnsertion Loss of 32.8 db/l00m at 250 MHz ,Cable should support operating temperature from -20°C to +60"C

Cable support Conductor Resistance ≤ 9.38ꭥ/100m Max., Cable support Delay Skew:< 45 ns/100m, Operating Voltage: 72V , Impedance: 100 ± 15 @100 MHz. and

Propagation Delay @250 MHz : 536 ns/100m, ETL Verified 4 connector channel performance with MTPL up to 635 MHz, Complaint to RoHS Directive 2011/65/EU and

11 MR (EU) 2015/863, OEM should have ISO 9001:2015, ISO 14001:2015 and ISO 45001:2018 or latest.All networking passive material. Each bundle having minimum of 305 No's 125 20,870.00 0.00 26,08,750.00

meters. (Fiber Cable, Copper Cables, Networking Racks and their connectivity components) should be from one OEM make only as per specification etc. all complete

Supply, Installation, Testing and Commissioning of Information Outlet Category 6A Keystone is Punch Down Type 50 Micron Gold Plating Suitable For 23~24 AWG

Stranded and Solid Wire. Skilled Design on Jack and PCB. Ergonomic Design and Easy Termination, Compliant to T568A and T568B Wiring Schemes, Backward

compatible with both RJ11/RJ12 Plug,Housing : High impact flame retardant plastic, UL 94V-O rated. ETL Verified 4 connector channel performance with MTPL up to 635

12 MR MHz, Complaint to RoHS Directive 2011/65/EU and (EU) 2015/863. OEM should have ISO 9001:2015, ISO 14001:2015, ISO 45001:2018 and should be present in India No's 900 325.00 0.00 2,92,500.00

for at-least 10 years or more. Blue Colour for Data as per specification etc. all complete

Supply, Installation, Testing and Commissioning of Information Outlet Category 6A Keystone is Punch Down Type 50 Micron Gold Plating Suitable For 23~24 AWG

Stranded and Solid Wire. Skilled Design on Jack and PCB. Ergonomic Design and Easy Termination, Compliant to T568A and T568B Wiring Schemes, Backward

compatible with both RJ11/RJ12 Plug,Housing : High impact flame retardant plastic, UL 94V-O rated. ETL Verified 4 connector channel performance with MTPL up to 635

13 MR MHz, Complaint to RoHS Directive 2011/65/EU and (EU) 2015/863. OEM should have ISO 9001:2015, ISO 14001:2015, ISO 45001:2018 and should be present in India No's 340 325.00 0.00 1,10,500.00

for at-least 10 years or more. Yellow Colour for Voice as per specification etc. all complete

Supply Installation Testing & Commissioning of 12 Core MM Fiber Oprtic Cable along with 12/24 Port LIU, Adapter Plate Pigtails and Fiber Patch cord etc all in

complete required for all Rack to Rack and floor to Floor for all 3 floors Connectivity all in complete for the facility in all respect, and registered under a ETL Followup

Program. Complaint to RoHS Directive 2011/65/EU and (EU) 2015/863. OEM should have ISO 9001:2015, ISO 14001:2015, ISO 45001:2018 and and should have a

14 MR certified PMP, CDCP and ITIL on the OEM’s payroll sitting in India whose services can be utilized for this project for Data as per given Specification etc. all complete Set 1 7,78,040.00 0.00 7,78,040.00

Supply, Installation, Testing and Commissioning of Layer 3 24port Core Switch with switching capacity of 3.2 Tbps, forwarding performance of 1 Bpps with 24x

1/10/25G Gigabit Ethernet + 4x 40/100G Uplink ports,Redundant hot swappable Power Supply and fans/Fantray.Should have advance layer 3 (RIPng, OSPF,IS-IS, BGP ,

VRF , VXLAN , 802.1x, Macsec , PIM SM, PIM SSM, PIM-BIDIR and MPLS) from day-1.MAC address support for 32 K , 200,000 IPv4 unicast routes and 100,000 IPv6

unicast routes entries ,32,000 IPv6 multicast routes , 25K Security ACL , Should support min 16 GB internal DRAM, 16 GB internal Flash memory , 32 MB Packet buffer.

15 MR Common Criteria Certification like NDPP or EAL and Ipv6 Certification from day-1 No's 2 15,19,060.00 0.00 30,38,120.00

Supply, Installation, Testing and Commissioning of Layer 2 48 Port POE+ Access Switch to provide ports with minimum PoE budget of 350W and 4x 10G SFP+ uplink

ports. Should support internal redundant Power Supply and support dedicated slot for modular stacking, in addition to asked uplink ports with stacking bandwidth of

minimum 80 Gbps with 8 switch in single stack. Switch should support minimum 30w on all ports, Should support min 2GB internal DRAM, 4GB internal Flash memory , 6

MB Packet buffer, 16 K MAC address, 11 K IPv4 routes ,1k Multicast Routes , 1500 ACL entries, Should have static, RIPv1, RIPv2, RIPng,OSPF, MACSEC,802.1x ,

PBR and VRRP from day 1 & upgradable to support IS-IS, VXLAN & VRF. Common Criteria Certification NDPP and Ipv6 Certification from day-1

Supply, Installation, Testing and Commissioning of Layer 2 48 Port Access Switch to provide 48 nos. 1G Base-T ports with 4x 10G SFP+ uplink ports. Should support

internal redundant Power Supply and support dedicated slot for modular stacking, in addition to asked uplink ports with stacking bandwidth of minimum 80 Gbps with 8

16b MR switch in single stack. Should support min 2GB internal DRAM, 4GB internal Flash memory , 6 MB Packet buffer, 16 K MAC address, 11 K IPv4 routes ,1k Multicast No's 6 3,25,000.00 0.00 19,50,000.00

Routes , 1500 ACL entries, Should have static, RIPv1, RIPv2, RIPng,OSPF, MACSEC,802.1x , PBR and VRRP from day 1 & upgradable to support IS-IS, VXLAN &

VRF. Common Criteria Certification NDPP and Ipv6 Certification from day-1

Supply, Installation, Testing and Commissioning of Layer 2 24 Port POE+ Access Switch to provide 24 nos. 1G Base-T ports with minimum PoE budget of 350W and

4x 10G SFP+ uplink ports. Should support internal redundant Power Supply and support dedicated slot for modular stacking, in addition to asked uplink ports with stacking

bandwidth of minimum 80 Gbps with 8 switch in single stack. Switch should support minimum 30w on all 24 ports, Should support min 2GB internal DRAM, 4GB internal

Flash memory , 6 MB Packet buffer, 16 K MAC address, 11 K IPv4 routes ,1k Multicast Routes , 1500 ACL entries, Should have static, RIPv1, RIPv2, RIPng,OSPF,

MACSEC,802.1x , PBR and VRRP from day 1 & upgradable to support IS-IS, VXLAN & VRF. Common Criteria Certification NDPP and Ipv6 Certification from day-1

Supply, Installation, Testing and Commissioning of Layer 2 24 Port Access Switch to provide 24 nos. 1G Base-T ports with 4x 10G SFP+ uplink ports. Should support

internal redundant Power Supply and support dedicated slot for modular stacking, in addition to asked uplink ports with stacking bandwidth of minimum 80 Gbps with 8

17b MR switch in single stack. Should support min 2GB internal DRAM, 4GB internal Flash memory , 6 MB Packet buffer, 16 K MAC address, 11 K IPv4 routes ,1k Multicast No's 3 2,61,840.00 0.00 7,85,520.00

Routes , 1500 ACL entries, Should have static, RIPv1, RIPv2, RIPng,OSPF, MACSEC,802.1x , PBR and VRRP from day 1 & upgradable to support IS-IS, VXLAN &

VRF. Common Criteria Certification NDPP and Ipv6 Certification from day-1

Supply, Installation, Testing and Commissioning of Wireless Indoor Access Point with 4 x 4 MU MIMO ,802.11ax (Wi-Fi 6) with data rates up to 5 Gbps , 1x

18a MR 100/1000/2500 Mbps Multigigabit Ethernet (RJ-45) – IEEE 802.3bz, 23dbm of transmit power in both 2.4Ghz and 5Ghz radios, Console port that uses Standard Port (RJ- No's 45 77,500.00 0.00 34,87,500.00

45) type connection , Must have -97 dB or better Receiver Sensitivity, AP shall support assurance, packet capture, RF sensing capabilitites

Supply, Installation, Testing & Commissioning of Wireless Controller, RF management, and quality of service (QoS) for voice and video, Guest Network

Management, Policy Management, should support up to 250 Access Point simultaneously and 5000 number of clients, Should support IEEE (802.11a/b/g,

18b MR 802.11ac, WMM/802.11e, 802.11h, 802.11k, 802.11n, 802.11r, 802.11u, 802.11w, 802.11ac), 1x Console Port (RJ45), 2x 10G/Multigigabit fiber ,Web-based: No's 2 9,50,000.00 0.00 19,00,000.00

HTTP/HTTPS, LED Activity Indicator, Includes Licenses ,Harware and Software, Complete in all respect as required by site etc.

Supply, Installation, testing and commissioning of Next Generation Firewall Must have 16X GE RJ45, 4X GE SFP, 4x 10 GE SFP+, 2X 25GE SFP28 and dedicated RJ45

Management from Day1. All required transceivers should be populated from day one. Threat prevention throughput of 10 Gbps in real world /production /enterprise mix

environment with all the security engines like IPS, Application control, web filtering, anti-malware etc, enabled. SSL VPN throughput of at least 4 Gbps. Should support

19 MR client based VPN and at least 6000 concurrent SSL VPN users from day 1. The solution should have 8 Gbps or more of SSL Inspection throughput with 800K or more No's 2 15,61,730.00 0.00 31,23,460.00

concurrent HTTPS session. Must support NAT (SNAT and DNAT) with following modes Static, Dynamic, PAT, Nat66 (IPv6-to-IPv6), Nat 64 (IPv6-to-IPv4), Nat46 (IPv4- to-

IPv6) , DNS64 & DHCPv6 functionality, The OEM of the offered products must have a valid ISO 9001:2015 and ISO27001. With 5 Year extended License

Supply Installation Testing & Commissioning of Internet Router which can support the Fiber Line as per the given Specification. The Router should be modular in

architecture with multicore processor Router should have 2 nos. of 10/100/1000 Base T-Pots and 2 nos should have SFP based ports option. The Router should have 2 x

10G from Day 1. Router should have 1x RJ-45 and 1xUSB Console port. should have 1:1 redundant internal and field replaceable, power supply 2 open slots for

additional LAN/WAN modules, 4GB DRAM active and 8 GB Compact, DES, 3DES and AES Standard support IPSec with IKEv2 and Suite- B Encryption. 1K GRE and 1K

IPSec Tunnels. OSPFv2. OSPFv3.BGP4. MBGP.BFD. Policy based routing IPv4 and IPv6 tunnelling.Router should support 750K IPv4 and IPv6 routes ,support IGMP

20 MR v1/v2/v3 and PIM multicast routing , MPLS and Firewall feature from Dav 1 ,Shall have 802.1q class of service and marking, classification policing and shaping. support No's 2 6,18,830.00 0.00 12,37,660.00

monitoring of network traffic with application. Router shall have traffic load balancing capability on dual WAN Link based , UL 60950 or IEC 60950 or CSA 60950 or EN

60950 Standards for Safety requirement,IPv6 Certifies IPv6 lago ready from Day 1 as per the given Specification etc. all complete. With One Year License

Supply Installation Testing & Commissioning The proposed IP-PBX/PABX/Communication System should employ IP at its core with IP switching technology. It should have

a Pure IP architecture with embedded hardware platform support to meet the technological demands of the present and future. The system should be IPv4 and IPV6

ready. Preference would be given to the manufacturer having DSIR recognized R&D. Preference would be given to the indigenous design manufacturer and made in India

product. The system should have VoIP at its core i.e. VoIP modules should be mounted on the CPU itself. The system should support SIP/IP extensions and trunks over

SIP protocol. It should be possible to support SIP Trunks and SIP/IP Extension with the single VoIP module. It should support up to 99 SIP trunks and 2100 SIP/IP users

(SIP/IP Phone, Mobile softphones, UC Client). The system should TDM ports through Gateways. The System should support SIP trunking and must be compatible with the

existing IPABX at the Head Office of the client for seamless integration.

It should be possible to reach the maximum capacity of the system of 2100 IP users without any add-on CPU or chassis/hardware platform. The architecture of the system

should be capable of seamless migration to its maximum capacity by simply purchasing a license for the same. The architecture should be non-stackable which eliminates

the individual power supply needed for each chassis required otherwise. VoIP should be a Daughter-board module mounted on a CPU. VoIP module(s) should support up

to 550 concurrent VoIP channels without transcoding, 248 concurrent VoIP channels with transcoding, 99 SIP trunks and 2100 SIP/IP users (SIP/IP Phone, Mobile

softphones, UC Client).

Voicemail features should be inbuilt in the system and should not require any additional hardware module. Voicemail features should be available to all the users

connected to the system without any license. The system should have adapter based power supply with output of 24V DC, 2.5A. It should have dual power supply port for

Hot redundancy. The system should support at least 21 concurrent Call Tapping and Conversation Recording. It should support a minimum 50 concurrent IP-IP Video calls

without using any VoIP Channel. The system should support UC Clients with following UC features:

21 MR Presence and Chat, Video Calling, Busy Lamp Field, Abbreviated Dialing (Global and Personal), Contact Grouping Drag and Drop Conference, Call Management - Call, No's 1 17,24,906.00 0.00 17,24,906.00

Hold, Transfer, Forward, DND & Intercom, Corporate Directory Integration, MS Outlook IntegrationCall Transfer & Direct Call to other User's Voicemail, Handover,

Calendar Integration, Click to Call , Menu options - Call Pickup, Paging, Message wait, Call Retrieve, Alarm and Reminder, Dynamic Lock, Dial-In Conference, CLIR,

Room monitoring & Call supervision, Multi-party Audio Conference, Drag and Drop Transfer, The system should support SIP over TLS and SRTP to ensure VoIP call

security over IP network. Following security features should be supported in the proposed system:

System should have provision to notify system log/activity to the administrator by email notification. System should provide reports of faults/activity through GUI in printable

format in online/offline mode System should have buffer of storing minimum 500 faults/error logs System should have notification of all alarms. All system activity and fault

logs should be saved in the system. The system should have MD5 Authentication for SIP and AES128 Password Protected Configuration by Admin and User. Password

Protection should have following features: The system should check the age of password before login into the system. The system must require the user to change the

password after every 90 days.

Changed password must not be the same as the previous password. The system should not allow the access of the Telnet and FTP server of PBX by any user. The

system must require the user to generate a strong password consisting of alphanumeric and special characters for System Login. The system should have two-level

access for users with different access rights. System should have two Gigabit Ethernet ports for LAN and WAN to separate out local and VoIP traffic on the external

network. System should have two external USB port to support various applications It should have built-in multi-party conferencing. It should be possible to carry out at

least 21 conferences of 3-participants at a time. The maximum number of participants in a single conference should be atleast 64. The system should have built-in Auto-

attendant facility and should be able to answer up to 64 calls simultaneously and should support dial-by-name.

The system should support multilingual IVR in at least 6 different languages in Auto-attendant. The system should have built-in web based software programming tool for

system administration. The system should have a built-in remote maintenance facility i.e. it should have the facility to be programmed remotely over the internet without

IP Phone Should Be Display: 128 x 64 –pixel Graphical LCD (3.1 Inch)

LED for Call and message wait Indication Intuitive user interface with icons

Feature Keys 3 Feature Keys : Headset, Mute , Hands-free speaker phone

4 Context Sensitive Keys 2 Line keys Function such as navigation, Call Appearance , feature status ∙ Volume Control Keys, Interface 2 X RJ45 10/100/1000 Mbps

22 MR Power Over Ethernet (IEEE 802.3af), 1 x RJ9 Handset port, 1 xRJ9 Headset port DC Power Jack No's 55 13,515.00 0.00 7,43,325.00

Enhanced Desktop Viewing LED for Call & message wait indication Intuitive user interface with Icon

Clear Voice Codec: G.722, G.711(A/μ), G.729, G.723

DTMF: In-band, Out-of-band

(RFC 2833) and SIP INFO

Full Duplex Speakerphone with VAD, CNG, AEC, AJB & AGC

SITC of IP Phone

· 2 x 10/100/1000 Mbps LAN & PC Ports

· Graphical LCD with Backlit

· LED for Incoming/Ongoing Call, Mute, Hold

· Add on 32 key module support, maximum key modules shall be supported

23 MR · Intuitive User Interface with Icons No's 175 8,524.00 0.00 14,91,700.00

· Multiple Languages Caller ID with Name, Number

· 45 or more keys including 4 Context Sensitive Hard Keys

· RJ9 Handset Port,RJ9 Headset Port,3.5 mm Headset Port

· Installation: Wall Mount, Table-top

SITC CE,FCC-15,RoHS,

of A4 & A3 A3 MFP's Power

Colourover Ethernet

LaserJet, 802.3af)

Core Functions Print, Copy, Scan, Send and optional fax, Engine Speed 40 ppm, Scan Speed 160 ipm, Send scans to

e-mail, PC, folder & Pendrive, RAM & HDD 7 GB & 500GB X 2, Control Panel 8 inch colour touch screen, Connectivity USB port & Network Port, Out put paper sizes A5,

24 MR A4, LGL, B4, A3 & SRA3 etc all required No's 9 5,00,000.00 0.00 45,00,000.00

Supply, Installation, Testing and Commissioning of Sifi and MTNL Express Connect MPLS with each Connection having 200mbps for 2 years

26 MR Supply, Installation, Testing and Commissioning of Sifi and MTNL Express Connect ILL with each Connection having 200mbps for 2 years No's 2 26,97,240.00 0.00 53,94,480.00

27 MR Supply, Installation, Testing and Commissioning of Jio/Airtel Express Connect ILL with each Connection having 100mbps for 5 years No's 1 21,28,000.00 0.00 21,28,000.00

Supply, Installation, Testing and Commissioning of A4 Color Laser Multifunction Printer, Perfect for Business Print, copy, scan, ADF, Duplex Print speed up to 25 ppm

(black) and 25 ppm (color) Dynamic security enabled printer USB, WiFi Wireless, Duplex Printing, Scan to email, Scan to PDF, Front USB flash drive port, Touchscreen,

28 MR TerraJet cartridge, Automatic document feeder, Print from phone or tablet (HP Laserjet color Pro MFP 4303FDW or equivalent) No's 24 1,11,231.89 0.00 26,69,565.36

Supply, Installation, Testing and Commissioning of A4 Black and White Laser Multifunction Printer, Perfect for Business Print, copy, scan, ADF, Duplex Print speed up to

29 MR 25 ppm (black) and 25 ppm (color) Dynamic security enabled printer USB, WiFi Wireless, Duplex Printing, Scan to email, Scan to PDF, Front USB flash drive port, No's 56 37,766.68 0.00 21,14,934.08

Touchscreen, TerraJet cartridge, Automatic document feeder, Print from phone or tablet (HP Laserjet Pro MFP 4104DW or equivalent)

Supply, Installation, Testing and Commissioning of All in One-14th Generation Intel® Core™ i9 processor Windows 11 Pro Intel® UHD Graphics 770 16 GB DDR5-4800

30 MR RAM 1 TB SSD Solid State Drive HP 125 Wired Keyboard, 1 VGA; 2 DisplayPort™ 1.4 with display size 23" etc all required No's 80 1,77,609.53 0.00 1,42,08,762.40

Supply, Installation, Testing and Commissioning of laptop- 13th Generation Intel® Core™ i9 processor Windows 11 Pro 40.6 cm (16) diagonal WUXGA display with

31 MR NVIDIA® GeForce RTX™ 4080 32 GB DDR5 RAM 2 TB SSD Solid State Drive B&O Speakers No's 11 2,84,048.85 0.00 31,24,537.35

34 MR SITC of Fiber Patch Cord 3 meter MM No's 46 2,500.00 1,15,000.00

AV BOQ for 6th Floor

S.No. Item Specifications Unit Qty Unit Price

NDSR Amount DSR Amount

SITC of LED wall display should have a maximum 1.2 mm pixel pitch and a size of 15.74 ft

x 4.42 ft. The controller should be from the same manufacturer and support video wall

resolution. The display should utilize maximum 1.2 mm pixel pitch direct LED wall COB type

technology. In terms of performance, the display should have a minimum brightness of 600

nits, a contrast ratio of 10000:1, and a viewing angle of 160° (horizontal and vertical). The

196" inch Video

1 refresh rate should be ≥3840 Hz, and the LED lifespan should be ≥ 100,000 hours. The Nos 1 ₹ 1,15,00,000.00 ₹ 1,15,00,000.00 0

display should have IP-based control and a minimum 14-bit processing capability. The tile

size should be 600 mm x 337.5 mm, with a 16:9 aspect ratio. The display should have an IP

rating of 20 and come with an LED OEM mount system. Additionally, the display should be

100% front serviceable for easy maintenance.

The operating temperature of the display should be between 0-40°C.

showing of upto 8 window simultaneously on a single screen or videowall as per layout

decided competent authority. System should have minimum 2 HDMI output each supporting

Supply, Installation, testing and commissioning of 65 inch UHD Signage/Professional

Display|400 Nits Brightness |50000:1 Contrast Ratio | 1xVGA; 2xUSB 2.0 , 4x HDMI 2.0 In,

Secure USB 2.0 (Internal), RJ45, RJ12, RS232, Optical SPDIF|1xHDMI 2.0 out, Supports

Daisy Chain |Speaker 2x10 W|30-degrees Tilting Installation | Open Content Management

3 65 inch Display Support, Scheduler, USB-Autoplay, AutoLaunch, HDMI-CEC, HDMI-Wakeup, Auto-switch Nos 4 ₹ 1,25,100.00 ₹ 5,00,400.00 0

on Failover, Panel Lock, OSD Rotation, NoSignalPowerOff, Screen Saver, Pixel

shift,Scheduler, Videowall support, Remote control via LAN, Realtime Clock, Joystick,

Rocker Switch| Optional : SDM or OPS compatibility, Embedded IR, IR extender option |

Optional: Overlay Touch Kit Compatibility|Certifications: Safety, EMC, CE

Supply, Installation, testing and commissioning of 55 inch UHD smart interactive display

with OPS, Resolution 3,840 x 2,160, Viewing Angle (H/V) 178/178, Response Time 8ms

SITC of Ultra Thin Retractable Touch Monitor Lifter With Screen, Material: Full

Retractor aluminum/alloy, Monitor: 15.6 inch FHD Screen (16:9) , Resolution ratio: 1920*1080 ,

Monitor Screen Brightness: 250 or more cd/m2 , Contrast: 600:1, Interface: HDMI+RS232 I/O+USB

etc all complete

SITC of Room booking system with remote and on-the-spot booking on an interactive touch

Room booking screen, 6-inch or more interactive screen, full capacitive touch screen interface, Resolution

system 1024 × 758 pixels.Viewing Angle 170°, connectivity 2.4 GHz Wi-Fi (IEEE 802.11 b/g/n)

standard, WPA2-PSK support etc all complete

Supply, Installation, testing and commissioning of wireless presentation device which should have

following features Wireless content input up to 1080P, HDMI 2.0 output, should Support native

wireless mirroring protocols like Airplay, Miracast, Chromecast should Support plug-n-play

7 HDMI/Type-C/U disk dongles for wireless connection, Support Windows APP for wireless connection Nos 1 ₹ 2,35,000.00 ₹ 2,35,000.00

(MAC APP will be available soon), Support 4 split screen view, Support wireless touch back on

interactive whiteboard/touch screen, Best-in-class data security with dual network and high standard

encryption, PoE supported, saving PSU when connecting with PoE ethernet switch

Supply, Installation, testing and commissioning of Cable cubby (1 HDMI, 1LAN,1 Charging

SITC of of Customised Metallic house structure, powder coated with caster wheels & brakes. Drawer

for keyboard, mouse and document camera. Wooden Top Tray for placing document & Laptop. All

drawers sliding tray and doors should be Lockable. External Passive Connectivity: HDMI 2.0 LAN

Cable, Power Socket with ON/OFF. 22”LCD Tablet Monitor with Resolution 1920 x 1080 . View Area

476.64(H) x 268.11(V) ㎜ – 22 inch. Luminance ,White 250 cd/㎡. Colour : 16.7M, Dynamic Contrast

Ratio 50,000:1 . Viewing Angle 85˚+85˚H and 80˚+80˚ V. Lamp Life Time 20,000 Hrs (min ).

Technology Electromagnetic Resonance. Detectable Height 3~10mm. Position Report Rate 138pps.

9 Digital Podium Pressure Resolution 1024 Level. CapacitiveTouch Technology:Projected Capacitive. Detacted object Nos 1 ₹ 2,24,000.00 ₹ 2,24,000.00

Fingers, or Conductive material. Tracking speed : 133<-. single :100:Multy:95. Accuracy : +-0.5mm /+-

3mm (Edge)3mm wide. Detect height 0-10mm. Motorized tilting adjustment for chainging viewing

angle. Minimum 6 Universal rating 5 Amp Socket. Provision to fix Logo at the front side. Provision of

19" minimum 12U Rack inside podium to fit in international standerd equipment. Access doors for

servicing both from front and back side of the podium. Wire manager on left & right side and at

bottom for flexibility of managing additional wire/wiring.

Supply Installation Testing and Commissioning of Full HD 1080p @ 60 frames per second

PTZ Camera with minimum 20X Optical Zoom and FoV of minimum 57 deg, min 100

Presets.Camera should support simultaneous outputs through Ethernet, HDMI, 3G-SDI,

Audio In and can be controlled via RS232 & 422 In & Out & IP.Panning angle -170° ~

+170°, Tilting angle -30° ~ +90° . The tilting and panning speed of camera should be

minimum 300° per second. Camera should support SRT, FreeD Protocol, PoE and Virtual

USB Driver. OEM should be CE, FCC, RoHS & BIS Certified with test lab report supporting

the certifications.

Supply, Installation, Testing & Commissioning of Processor which can enable Voice

Tracking through PTZ Cameras integrated with Ceiling Tiles on IP. The Processor should

11 Tracking Device be capable of connecting minimum 4x Ceiling Tiles with 4x IP based PTZ Cameras for Nos 1 ₹ 3,85,900.00 ₹ 3,85,900.00

Quadview output and Auto Switching . The processor should have USB 3.0 Output for Soft

VC. Quoted model should be BIS, CE, FCC & RoHS Certified with Test Lab Reports.

Video SITC of Video conferencing Codec with Dual HDMI, supports 4K presentation, Support 256

12 conferencing AES Encryption, POE+ Injector, 10 Meter HDMI cable, 1 year supportetc all complete etc Nos 1 ₹ 12,57,000.00 ₹ 12,57,000.00

Codec all complete

SITC of capture card Supports Ultra HD 4K, 1440p, 1080p, 1080i, 720p, 480p, and 576p

graphic formats Up to Ultra HD 4K (3840/4096×2160) at 30 fps and 1080p at 60 fps HDMI

audio support: Embedded audio in the HDMI signals is extracted and output as two-channel

LPCM Digital Fluid technology: Internal frame buffers maximize frame rate with any PC

Hardware-based color space and sampling conversion

SITC of UHD+ HDMI over HDBaseT Receiver with HDR 4K@60 444 up to 100M. Supports

Deep Color input and output up to 12-bit. Simultaneous transmission of video, audio and

data over a single Cat.5e/6/7 cable up to 100m (328ft) at 1080p and 246ft at 4K. Control

14 Receiver Bidirectional IR/RS-232 pass-through. Integrated AVLC (Adaptive Visually Lossless Nos 10 ₹ 72,000.00 ₹ 7,20,000.00

Compression) activates when the bandwidth requirements of the source are beyond

10.2Gbps (340MHz) allowing for support of sources up to 18Gbps (600MHz) with no loss of

visual quality.

SITC of UHD+ HDMI over HDBaseT transmitter with HDR 4K@60 444 up to 100M.

Supports Deep Color input and output up to 12-bit. Simultaneous transmission of video,

audio and data over a single Cat.5e/6/7 cable up to 100m (328ft) at 1080p and 246ft at 4K.

15 Transmitter Control Bidirectional IR/RS-232 pass-through. Integrated AVLC (Adaptive Visually Lossless Nos 10 ₹ 72,000.00 ₹ 7,20,000.00

Compression) activates when the bandwidth requirements of the source are beyond

10.2Gbps (340MHz) allowing for support of sources up to 18Gbps (600MHz) with no loss of

visual quality.

Supply, Installation, testing and commissioning of Eight HDMI inputs matrixed to eight

HDMI outputs with HDMI 2.0a specification and 18Gbps (600MHz) 4K UHD support, HD

resolutions up to 3840×2160@60Hz (4:4:4, 8-bit) & 4096×2160@60Hz (4:4:4, 8-bit), 16-bit

16 Deep Color up to 1080p@60Hz. Eight Audio output ports can pair with eight HDMI outputs Nos 1 ₹ 4,32,700.00 ₹ 4,32,700.00

individually. Audio support Digital and analog Formats. Device should be provides an

intuitive set of front panel controls with an LCD as well as RS-232, Telnet, WebGUI, and IR

remote control options.

Supply, Installation, testing and commissioning of Ceiling microphone with automatic

dynamic Beamforming technology, The beam will automatically detect the position of the

person speaking and will follow the person around the room at all times. It should have 2 x

Dante digital audio (Redundancy), Analog audio out (Phoenix 3-pin), and Ethernet for

Control and PoE connectivity ports. The coverage of the ceiling microphone should be min

800 square feet or more. It should have a true voice lift feature to increase audio

17 intelligibility above the ambient noise floor. It should support IT industry standards like IEEE Nos 4 ₹ 5,10,221.00 ₹ 20,40,884.00 0

802.1x. It can be controlled through software that can control and monitor the microphone

in any network. It should have min 100 dB SPL, 5ms latency, and min 90dBA or higher

dynamic range. High-precision audio settings for maximum control, setting to exclude (min

5) and prioritize the areas of the room. It should certified from Microsoft Teams and Zoom

Video conferencing applications. It should have UL 62368 certification (including UL 2043

testing and compliance) and safety certifications.

SITC of 450mm Gooseneck microphone with a programmable microphone button (Toggle

Wired on/ off, PTM, PTT, and permanent on) and a bi-color LED ring for status indication. 450mm

18 Gooseneck length, condenser capsule with cardioid pickup pattern, Frequency response: 50 Hz - 20 Nos 1 ₹ 74,000.00 ₹ 74,000.00

microphone kHz, Maximum sound pressure level: 130 dB SPL, Connectivity: XLR 3M. It should have

TTL-logic output for camera control feature

Suppy Installation Testing and Commissioning of digital signal processor with minimum

14no. Or more Mic / line input with phantom power and AEC and 8 or more line level output,

1no. Or more GPIO at least 2 channel of USB input and output for software Video

Digital Signal Conferencing, should have 64x64 channel of digital dante input output, Should have

Processor sampline rate of 48kHz or better, Should be expandable for port expansion, should support

Control with App via iOS and Android devices, or any third-party control system, Shall

have Built-in filters, feedback suppression, AGC single-device(chassis) use is permitted, but

the combination of devices is not accepted etc complete as required as per specifications

Supply, Installation, testing and commissioning of 4 channel energy star rated digital power

amplifier,4 channel at 4 Ohm or 8 ohm energy-efficient amplifier - 4 x 80W or more at

70/100V Technology : Class-D,Input linking through miniature switches, Switching mode

power supply, Protection : DC Short circuit & Over heating & Over load & Signal limiting,

Frequency Response 120 Hz - 20 kHz or better, Silent passive cooling etc complete

required as per specifications.

Supply, Installation, testing and commissioning of 6.5" two-way coaxial thin edge ceiling

loudspeaker having 100V transformer power taps from 60watts to 15watts or better it

should have metal back can for premium performance in demanding applications, Conical

21 Speaker dispersion : 142° or more, Low impedance RMS continuous power of 60watts, impedance : Nos 8 ₹ 21,497.00 ₹ 1,71,976.00 0

8 or less,frequency range (-10dB) : 70 Hz - 20 kHz, frequency response (±3dB) : 100Hz -

20KHz, Max SPL on 100v should be 105dB or more etc complete required as per

specifications.

Suppy Installation Testing and Commissioning of control system with touch panel/Ipad,

100/1000 Mbps, auto‑switching, auto‑negotiating, auto‑discovery, full/half duplex, industry-

standard TCP/IP stack, UDP/IP, CIP, DHCP, SSL, TLS, SSH, SFTP (SSH File Transfer

Protocol), FIPS 140-2 compliant encryption

23 Supply, Installation, testing and commissioning of 16 port switch Nos 1 ₹ 65,500.00 ₹ 65,500.00

Supply Installation Testing and Commissioning of surface-mount USB-to-Dante endpoint,

two-way volume and mute sync for Microsoft Teams,compliant with CE and FCC, device

shouold have Power-over-Ethernet (PoE) to IEEE 802.3af Class 0 standard and support

24 Dante networking using standard CatX cable, device should support the Speakerphone Nos 1 ₹ 1,95,500.00 ₹ 1,95,500.00

profile with and without echo cancellation, enable two-way volume and mute syncronization

with both PC and Mac platforms, Dante with AES67 compliance,Sampling Rate(s) 48

kHz,should be from same OEM as DSP etc complete required as per specifications.

Supply, Installation, Testing & Commissioning of USB 3.2 Extenders. Transmitter should

have 1xUSB C input port, 1X RJ45, 1xUSB-A Output Port. Receiver should have Input Port

25 USB Tx Rx 1×Cat5e/6A/7 (RJ45). 1×USB-C, 3×USB-A Output Port. Bandwidth upto 5Gbps Nos 2 ₹ 96,000.00 ₹ 1,92,000.00

(SuperSpeed), Tranmission distance upto 100M. Devices should be controlable by the USB

host on a transmitter. Should have backward compatibility with USB 2.0

Supply Installation Testing and Commissioning of HDMI Audio Extractor should extract up

to 2 channels of LPCM audio or 5.1 channels of Bitstream audio from an HDMI source,

allowing the user to convert high quality HDMI audio into more convenient analog (LPCM

2.0 sources only) or optical signals for use with powered speakers or non-HDMI AV

receivers. Both the input and output HDMI ports should support 4K UHD resolutions up to

26 4K@60Hz (4:4:4, 8-bit) and should capable of providing high quality audio and video Nos 1 ₹ 93,100.00 ₹ 93,100.00

performance. The unit should supports passthrough of HD and standard Bitstream formats

as well as LPCM 7.1 with audio sampling rates up to 192kHz. Built-in EDID management

support allows the user select from multiple EDIDs and, with the use of optional PC

software, to upload, download, or edit EDID files etc and complete as required

27 HDMI Cable SITC of 3 feet Premium High Speed HDMI 2.0 cable Nos 20 ₹ 4,720.00 ₹ 94,400.00

28 HDMI Cable SITC of 6 feet Premium High Speed HDMI 2.0 cable Nos 5 ₹ 5,310.00 ₹ 26,550.00

29 HDMI Cable SITC of 15 feet Premium High Speed HDMI 2.0 cable Nos 5 ₹ 6,232.00 ₹ 31,160.00

30 HDMI Cable SITC of 10 Meter Active Copper HDMI Cable Nos 4 ₹ 13,338.00 ₹ 53,352.00

SITC of 6 USB hub Enables 4 computers to share 4 USB 3.2 Gen1 devices Support port

selection via remote controller or RS-422/RS-485 link through 5-pin terminal block

SITC of 10 Meter USB 3.1 Gen1 SuperSpeed Active Extension Cable TypeA/male to

Microphone SITC of Microphone Cable, 2 Conductor 22 AWG PVC Jacket (as per actual) etc all

Cable complete

SITC of 2 Conductor 16 AWG Speaker Cable, PVC jacket (as per actual) etc all

Category 6 SITC of Category 6A Cable, 4 Pair, S/FTP, PVC jacket (as per actual) etc all complete

SITC of 24U, Equipment Rack, with Front glass door, 4 x Fan, 4 Caster wheels, 2 x Shelfs ,

Total Board Room ₹ 2,38,07,766.00

Mini Board Room

S.No. Item Specifications Unit Qty Unit Price

NDSR Amount DSR Amount

SITC of 98" UHD Signage/Professional Display|500 Nits Brightness |50000:1 Contrast

Ratio|Operation: 24x7|1xVGA; 1xDP, 2xUSB 2.0 , 4x HDMI 2.0 In, Secure USB 2.0

(Internal), RJ45, RJ12, RS232, Optical SPDIF |1xHDMI 2.0, 1xDP Out, Supports Daisy

Chain| Speaker 2x12 W | Open Content Management Support, Scheduler, USB Autoplay,

AutoLaunch, HDMI-CEC, HDMI-Wakeup, Auto-switch on Failover, Panel Lock, OSD

Rotation, NoSignalPowerOff, Screen Saver, Pixel shift, Scheduler, Videowall support,

Remote control via LAN, Realtime Clock, Joystick, Rocker Switch| Optional : OPS

compatibility |Certifications: Safety, EMC, CE

Supply, Installation, testing and commissioning of 65 inch UHD Signage/Professional

Display|400 Nits Brightness |50000:1 Contrast Ratio | 1xVGA; 2xUSB 2.0 , 4x HDMI 2.0 In,

Secure USB 2.0 (Internal), RJ45, RJ12, RS232, Optical SPDIF|1xHDMI 2.0 out, Supports

Daisy Chain |Speaker 2x10 W|30-degrees Tilting Installation | Open Content Management

2 65 inch Display Support, Scheduler, USB-Autoplay, AutoLaunch, HDMI-CEC, HDMI-Wakeup, Auto-switch Nos 2 ₹ 1,25,100.00 ₹ 2,50,200.00 0

on Failover, Panel Lock, OSD Rotation, NoSignalPowerOff, Screen Saver, Pixel

shift,Scheduler, Videowall support, Remote control via LAN, Realtime Clock, Joystick,

Rocker Switch| Optional : SDM or OPS compatibility, Embedded IR, IR extender option |

|Certifications: Safety, EMC, CE

SITC of Ultra Thin Retractable Touch Monitor Lifter With Screen, Material: Full

Retractor aluminum/alloy, Monitor: 15.6 inch FHD Screen (16:9) , Resolution ratio: 1920*1080 ,

Monitor Screen Brightness: 250 or more cd/m2 , Contrast: 600:1, Interface: HDMI+RS232 I/O+USB

etc all complete

SITC of Room booking system with remote and on-the-spot booking on an interactive touch

Room booking screen, 6-inch or more interactive screen, full capacitive touch screen interface, Resolution

system 1024 × 758 pixels.Viewing Angle 170°, connectivity 2.4 GHz Wi-Fi (IEEE 802.11 b/g/n)

standard, WPA2-PSK support etc all complete

Supply, Installation, testing and commissioning of wireless presentation device which should have

following features Wireless content input up to 1080P, HDMI 2.0 output, should Support native

wireless mirroring protocols like Airplay, Miracast, Chromecast should Support plug-n-play

5 HDMI/Type-C/U disk dongles for wireless connection, Support Windows APP for wireless connection Nos 1 ₹ 2,35,000.00 ₹ 2,35,000.00

(MAC APP will be available soon), Support 4 split screen view, Support wireless touch back on

interactive whiteboard/touch screen, Best-in-class data security with dual network and high standard

encryption, PoE supported, saving PSU when connecting with PoE ethernet switch

Supply, Installation, testing and commissioning of Cable cubby (1 HDMI, 1LAN,1 Charging

Supply Installation Testing and Commissioning of Full HD 1080p @ 60 frames per second

PTZ Camera with minimum 20X Optical Zoom and FoV of minimum 57 deg, min 100

Presets.Camera should support simultaneous outputs through Ethernet, HDMI, 3G-SDI,

Audio In and can be controlled via RS232 & 422 In & Out & IP.Panning angle -170° ~

+170°, Tilting angle -30° ~ +90° . The tilting and panning speed of camera should be

minimum 300° per second. Camera should support SRT, FreeD Protocol, PoE and Virtual

USB Driver. OEM should be CE, FCC, RoHS & BIS Certified with test lab report supporting

the certifications.

Supply, Installation, Testing & Commissioning of Processor which can enable Voice

Tracking through PTZ Cameras integrated with Ceiling Tiles on IP. The Processor should

8 Tracking Device be capable of connecting minimum 4x Ceiling Tiles with 4x IP based PTZ Cameras for Nos 1 ₹ 3,85,900.00 ₹ 3,85,900.00

Quadview output and Auto Switching . The processor should have USB 3.0 Output for Soft

VC. Quoted model should be BIS, CE, FCC & RoHS Certified with Test Lab Reports.

SITC of capture card Supports Ultra HD 4K, 1440p, 1080p, 1080i, 720p, 480p, and 576p

graphic formats Up to Ultra HD 4K (3840/4096×2160) at 30 fps and 1080p at 60 fps HDMI

audio support: Embedded audio in the HDMI signals is extracted and output as two-channel

LPCM Digital Fluid technology: Internal frame buffers maximize frame rate with any PC

Hardware-based color space and sampling conversion

SITC of UHD+ HDMI over HDBaseT Receiver with HDR 4K@60 444 up to 100M. Supports

Deep Color input and output up to 12-bit. Simultaneous transmission of video, audio and

data over a single Cat.5e/6/7 cable up to 100m (328ft) at 1080p and 246ft at 4K. Control

10 Receiver Bidirectional IR/RS-232 pass-through. Integrated AVLC (Adaptive Visually Lossless Nos 6 ₹ 72,000.00 ₹ 4,32,000.00

Compression) activates when the bandwidth requirements of the source are beyond

10.2Gbps (340MHz) allowing for support of sources up to 18Gbps (600MHz) with no loss of

visual quality.

SITC of UHD+ HDMI over HDBaseT transmitter with HDR 4K@60 444 up to 100M.

Supports Deep Color input and output up to 12-bit. Simultaneous transmission of video,

audio and data over a single Cat.5e/6/7 cable up to 100m (328ft) at 1080p and 246ft at 4K.

11 Transmitter Control Bidirectional IR/RS-232 pass-through. Integrated AVLC (Adaptive Visually Lossless Nos 6 ₹ 72,000.00 ₹ 4,32,000.00

Compression) activates when the bandwidth requirements of the source are beyond

10.2Gbps (340MHz) allowing for support of sources up to 18Gbps (600MHz) with no loss of

visual quality.

Supply, Installation, testing and commissioning of Eight HDMI inputs matrixed to eight

HDMI outputs with HDMI 2.0a specification and 18Gbps (600MHz) 4K UHD support, HD

resolutions up to 3840×2160@60Hz (4:4:4, 8-bit) & 4096×2160@60Hz (4:4:4, 8-bit), 16-bit

12 Deep Color up to 1080p@60Hz. Eight Audio output ports can pair with eight HDMI outputs Nos 1 ₹ 4,32,700.00 ₹ 4,32,700.00

individually. Audio support Digital and analog Formats. Device should be provides an

intuitive set of front panel controls with an LCD as well as RS-232, Telnet, WebGUI, and IR

remote control options.

Supply, Installation, testing and commissioning of Ceiling microphone with automatic

dynamic Beamforming technology, The beam will automatically detect the position of the

person speaking and will follow the person around the room at all times. It should have 2 x

Dante digital audio (Redundancy), Analog audio out (Phoenix 3-pin), and Ethernet for

Control and PoE connectivity ports. The coverage of the ceiling microphone should be min

800 square feet or more. It should have a true voice lift feature to increase audio

13 intelligibility above the ambient noise floor. It should support IT industry standards like IEEE Nos 2 ₹ 5,10,221.00 ₹ 10,20,442.00 0

802.1x. It can be controlled through software that can control and monitor the microphone

in any network. It should have min 100 dB SPL, 5ms latency, and min 90dBA or higher

dynamic range. High-precision audio settings for maximum control, setting to exclude (min

5) and prioritize the areas of the room. It should certified from Microsoft Teams and Zoom

Video conferencing applications. It should have UL 62368 certification (including UL 2043

testing and compliance) and safety certifications.

Suppy Installation Testing and Commissioning of digital signal processor with minimum

14no. Or more Mic / line input with phantom power and AEC and 8 or more line level output,

1no. Or more GPIO at least 2 channel of USB input and output for software Video

Digital Signal Conferencing, should have 64x64 channel of digital dante input output, Should have

Processor sampline rate of 48kHz or better, Should be expandable for port expansion, should support

Control with App via iOS and Android devices, or any third-party control system, Shall

have Built-in filters, feedback suppression, AGC single-device(chassis) use is permitted, but

the combination of devices is not accepted etc complete as required as per specifications

Supply, Installation, testing and commissioning of 4 channel energy star rated digital power

amplifier,4 channel at 4 Ohm or 8 ohm energy-efficient amplifier - 4 x 80W or more at

70/100V Technology : Class-D,Input linking through miniature switches, Switching mode

power supply, Protection : DC Short circuit & Over heating & Over load & Signal limiting,

Frequency Response 120 Hz - 20 kHz or better, Silent passive cooling etc complete

required as per specifications.

Supply, Installation, testing and commissioning of 6.5" two-way coaxial thin edge ceiling

loudspeaker having 100V transformer power taps from 60watts to 15watts or better it

should have metal back can for premium performance in demanding applications, Conical

16 Speaker dispersion : 142° or more, Low impedance RMS continuous power of 60watts, impedance : Nos 6 ₹ 21,497.00 ₹ 1,28,982.00 0

8 or less,frequency range (-10dB) : 70 Hz - 20 kHz, frequency response (±3dB) : 100Hz -

20KHz, Max SPL on 100v should be 105dB or more etc complete required as per

specifications.

Suppy Installation Testing and Commissioning of control system with touch panel/Ipad,

100/1000 Mbps, auto‑switching, auto‑negotiating, auto‑discovery, full/half duplex, industry-

standard TCP/IP stack, UDP/IP, CIP, DHCP, SSL, TLS, SSH, SFTP (SSH File Transfer

Protocol), FIPS 140-2 compliant encryption

18 Supply, Installation, testing and commissioning of 16 port switch Nos 1 ₹ 65,500.00 ₹ 65,500.00

Supply Installation Testing and Commissioning of surface-mount USB-to-Dante endpoint,

two-way volume and mute sync for Microsoft Teams,compliant with CE and FCC, device

shouold have Power-over-Ethernet (PoE) to IEEE 802.3af Class 0 standard and support

19 Dante networking using standard CatX cable, device should support the Speakerphone Nos 1 ₹ 1,95,500.00 ₹ 1,95,500.00

profile with and without echo cancellation, enable two-way volume and mute syncronization

with both PC and Mac platforms, Dante with AES67 compliance,Sampling Rate(s) 48

kHz,should be from same OEM as DSP etc complete required as per specifications.

Supply, Installation, Testing & Commissioning of USB 3.2 Extenders. Transmitter should

have 1xUSB C input port, 1X RJ45, 1xUSB-A Output Port. Receiver should have Input Port

20 USB Tx Rx 1×Cat5e/6A/7 (RJ45). 1×USB-C, 3×USB-A Output Port. Bandwidth upto 5Gbps Nos 1 ₹ 96,000.00 ₹ 96,000.00

(SuperSpeed), Tranmission distance upto 100M. Devices should be controlable by the USB

host on a transmitter. Should have backward compatibility with USB 2.0

Supply Installation Testing and Commissioning of HDMI Audio Extractor should extract up

to 2 channels of LPCM audio or 5.1 channels of Bitstream audio from an HDMI source,

allowing the user to convert high quality HDMI audio into more convenient analog (LPCM

2.0 sources only) or optical signals for use with powered speakers or non-HDMI AV

receivers. Both the input and output HDMI ports should support 4K UHD resolutions up to

21 4K@60Hz (4:4:4, 8-bit) and should capable of providing high quality audio and video Nos 1 ₹ 93,100.00 ₹ 93,100.00

performance. The unit should supports passthrough of HD and standard Bitstream formats

as well as LPCM 7.1 with audio sampling rates up to 192kHz. Built-in EDID management

support allows the user select from multiple EDIDs and, with the use of optional PC

software, to upload, download, or edit EDID files etc and complete as required

22 HDMI Cable SITC of 3 feet Premium High Speed HDMI 2.0 cable Nos 16 ₹ 4,720.00 ₹ 75,520.00

23 HDMI Cable SITC of 6 feet Premium High Speed HDMI 2.0 cable Nos 3 ₹ 5,310.00 ₹ 15,930.00

24 HDMI Cable SITC of 15 feet Premium High Speed HDMI 2.0 cable Nos 3 ₹ 6,232.00 ₹ 18,696.00

25 HDMI Cable SITC of 10 Meter Active Copper HDMI Cable Nos 2 ₹ 13,338.00 ₹ 26,676.00

SITC of 6 USB hub Enables 4 computers to share 4 USB 3.2 Gen1 devices Support port

selection via remote controller or RS-422/RS-485 link through 5-pin terminal block

SITC of 10 Meter USB 3.1 Gen1 SuperSpeed Active Extension Cable TypeA/male to

Microphone SITC of Microphone Cable, 2 Conductor 22 AWG PVC Jacket (as per actual) etc all

Cable complete

SITC of 2 Conductor 16 AWG Speaker Cable, PVC jacket (as per actual) etc all

Category 6 SITC of Category 6A Cable, 4 Pair, S/FTP, PVC jacket (as per actual) etc all complete

SITC of 24U, Equipment Rack, with Front glass door, 4 x Fan, 4 Caster wheels, 2 x Shelfs ,

Total Mini Board Room ₹ 73,67,643.00

Multy Purpose Hall

SITC of LED wall display should have a maximum 1.2 mm pixel pitch and a size of 15.74 ft

x 4.42 ft. The controller should be from the same manufacturer and support video wall

resolution. The display should utilize maximum 1.2 mm pixel pitch direct LED wall COB type

technology. In terms of performance, the display should have a minimum brightness of 600

nits, a contrast ratio of 10000:1, and a viewing angle of 160° (horizontal and vertical). The

196" inch Video refresh rate should be ≥3840 Hz, and the LED lifespan should be ≥ 100,000 hours. The

Wall display should have IP-based control and a minimum 14-bit processing capability. The tile

size should be 600 mm x 337.5 mm, with a 16:9 aspect ratio. The display should have an IP

rating of 20 and come with an LED OEM mount system. Additionally, the display should be

100% front serviceable for easy maintenance.

The operating temperature of the display should be between 0-40°C.Approved makes:

Christie/NEC/Daktronics

showing of upto 8 window simultaneously on a single screen or videowall as per layout

decided competent authority. System should have minimum 2 HDMI output each supporting

4K resolution without compromising the resolution on any panel, colour, pixels and aspect

ratio. Must have provision to increase number of outputs by replacing/adding necessary

cards. Device must support input resolutions from 720p (1280x720) @ 23.98, 24, 25, 29.97,

capable to accept SMPTE259M-C & SMPTE292M by using necessary cards.. The video

wall processor must have minimum 2 VW canvas and must support multiple canvas without

disturbing each other. Each canvas should support symmetric and asymmetric both kind of

Video wall along with minimum features like Video Matrixing, Picture in picture, Multi

windowing, source overlaying & Outputs rotation in 1-degree increments for having 360-

degree rotation, Must have option to add Customisable borders to windows/inputs. Systems

must have other key features like HDCP Compliant, Real-time status feedback through

events, Live dashboard to switch pre-sets and window sources, Custom Resolution Editor

with resolutions auto detected on inputs & selectable on the outputs along with option to

make custom display/active Led by entering actual dimension & pixel info of the

display/panel physically used, Combination of different size and resolution of displays can

be used, option to handle custom aspect ratio on inputs and output side both and to handle

Non-standard aspect ratio active LED, Must have provision to store minimum 20 custom

resolutions, Must have output cloning option to easily set up repeat displays, duplicated

side screens and facilitate third party screen recording, Adjustable bezel compensation,

Horizontal alignment on analog PC inputs, Up-Down-Cross Conversion, EDID manager, De-

embedded audio out & minimum 50 pre-sets should be saved permanently in the system,

The source position and the sizes to be saved as a layout for the preset recall and should

support multiple layouts, AES Decryption -if using IP card must Decode IP streams that

have been encrypted using the AES CBC standard using 128 or 256-bit key length. Secure

comms: for keeping information safe with HTTPS SSL connectivity and experience RESTful

multi-user control with remote monitoring or equivalent. Must have built in Audio matrixing

Supply Installation Testing and Commissioning of Full HD 1080p @ 60 frames per second

PTZ Camera with minimum 20X Optical Zoom and FoV of minimum 57 deg, min 100

Presets.Camera should support simultaneous outputs through Ethernet, HDMI, 3G-SDI,

Audio In and can be controlled via RS232 & 422 In & Out & IP.Panning angle -170° ~

+170°, Tilting angle -30° ~ +90° . The tilting and panning speed of camera should be

minimum 300° per second. Camera should support SRT, FreeD Protocol, PoE and Virtual

USB Driver. OEM should be CE, FCC, RoHS & BIS Certified with test lab report supporting

the certifications.

Video SITC of Video conferencing Codec with Dual HDMI, supports 4K presentation, Support 256

4 conferencing AES Encryption, POE+ Injector, 10 Meter HDMI cable, 1 year supportetc all complete etc Nos 0 ₹ 12,57,000.00 ₹ -

Code all complete

SITC of capture card Supports Ultra HD 4K, 1440p, 1080p, 1080i, 720p, 480p, and 576p

graphic formats Up to Ultra HD 4K (3840/4096×2160) at 30 fps and 1080p at 60 fps HDMI

5 Capture Card Nos 0 ₹ 1,35,000.00 ₹ -

audio support: Embedded audio in the HDMI signals is extracted and output as two-channel

LPCM Digital Fluid technology: Internal frame buffers maximize frame rate with any PC

Hardware-based color space and sampling conversion

SITC of UHD+ HDMI over HDBaseT Receiver with HDR 4K@60 444 up to 100M. Supports

Deep Color input and output up to 12-bit. Simultaneous transmission of video, audio and

data over a single Cat.5e/6/7 cable up to 100m (328ft) at 1080p and 246ft at 4K. Control

6 Receiver Bidirectional IR/RS-232 pass-through. Integrated AVLC (Adaptive Visually Lossless Nos 4 ₹ 72,000.00 ₹ 2,88,000.00

Compression) activates when the bandwidth requirements of the source are beyond

10.2Gbps (340MHz) allowing for support of sources up to 18Gbps (600MHz) with no loss of

visual quality.

SITC of UHD+ HDMI over HDBaseT transmitter with HDR 4K@60 444 up to 100M.

Supports Deep Color input and output up to 12-bit. Simultaneous transmission of video,

audio and data over a single Cat.5e/6/7 cable up to 100m (328ft) at 1080p and 246ft at 4K.

7 Transmitter Control Bidirectional IR/RS-232 pass-through. Integrated AVLC (Adaptive Visually Lossless Nos 4 ₹ 72,000.00 ₹ 2,88,000.00

Compression) activates when the bandwidth requirements of the source are beyond

10.2Gbps (340MHz) allowing for support of sources up to 18Gbps (600MHz) with no loss of

visual quality.

Supply, Installation, testing and commissioning of wireless presentation device which should have

following features Wireless content input up to 1080P, HDMI 2.0 output, should Support native

wireless mirroring protocols like Airplay, Miracast, Chromecast should Support plug-n-play

8 HDMI/Type-C/U disk dongles for wireless connection, Support Windows APP for wireless connection Nos 1 ₹ 2,35,000.00 ₹ 2,35,000.00

(MAC APP will be available soon), Support 4 split screen view, Support wireless touch back on

interactive whiteboard/touch screen, Best-in-class data security with dual network and high standard

encryption, PoE supported, saving PSU when connecting with PoE ethernet switch

Supply, Installation, testing and commissioning of Four HDMI inputs matrixed to Four HDMI

outputs with HDMI 2.0a specification and 18Gbps (600MHz) 4K UHD support, HD

resolutions up to 3840×2160@60Hz (4:4:4, 8-bit) & 4096×2160@60Hz (4:4:4, 8-bit), 16-bit

9 Deep Color up to 1080p@60Hz. Four Audio output ports can pair with Four HDMI outputs Nos 1 ₹ 2,75,700.00 ₹ 2,75,700.00

individually. Audio support Digital and analog Formats. Device should be provides an

intuitive set of front panel controls with an LCD as well as RS-232, Telnet, WebGUI, and IR

remote control options.

Supply, Installation, testing and commissioning of Ceiling microphone with automatic

dynamic Beamforming technology, The beam will automatically detect the position of the

person speaking and will follow the person around the room at all times. It should have 2 x

Dante digital audio (Redundancy), Analog audio out (Phoenix 3-pin), and Ethernet for

Control and PoE connectivity ports. The coverage of the ceiling microphone should be min

800 square feet or more. It should have a true voice lift feature to increase audio

10 intelligibility above the ambient noise floor. It should support IT industry standards like IEEE Nos 6 ₹ 5,10,221.00 ₹ 30,61,326.00

802.1x. It can be controlled through software that can control and monitor the microphone

in any network. It should have min 100 dB SPL, 5ms latency, and min 90dBA or higher

dynamic range. High-precision audio settings for maximum control, setting to exclude (min

5) and prioritize the areas of the room. It should certified from Microsoft Teams and Zoom

Video conferencing applications. It should have UL 62368 certification (including UL 2043

testing and compliance) and safety certifications.

Suppy Installation Testing and Commissioning of digital signal processor with minimum

14no. Or more Mic / line input with phantom power and AEC and 8 or more line level output,

1no. Or more GPIO at least 2 channel of USB input and output for software Video

Digital Signal Conferencing, should have 64x64 channel of digital dante input output, Should have

Processor sampline rate of 48kHz or better, Should be expandable for port expansion, should support

Control with App via iOS and Android devices, or any third-party control system, Shall

have Built-in filters, feedback suppression, AGC single-device(chassis) use is permitted, but

the combination of devices is not accepted etc complete as required as per specifications

Supply, Installation, testing and commissioning of 4 channel energy star rated digital power

amplifier,4 channel at 4 Ohm or 8 ohm energy-efficient amplifier - 4 x 80W or more at

70/100V Technology : Class-D,Input linking through miniature switches, Switching mode

power supply, Protection : DC Short circuit & Over heating & Over load & Signal limiting,

Frequency Response 120 Hz - 20 kHz or better, Silent passive cooling etc complete

required as per specifications.

Supply, Installation, testing and commissioning of 6.5" two-way coaxial thin edge ceiling

loudspeaker having 100V transformer power taps from 60watts to 15watts or better it

should have metal back can for premium performance in demanding applications, Conical

13 Speaker dispersion : 142° or more, Low impedance RMS continuous power of 60watts, impedance : Nos 8 ₹ 21,497.00 ₹ 1,71,976.00

8 or less,frequency range (-10dB) : 70 Hz - 20 kHz, frequency response (±3dB) : 100Hz -

20KHz, Max SPL on 100v should be 105dB or more etc complete required as per

specifications.

Suppy Installation Testing and Commissioning of control system with touch panel/Ipad,

100/1000 Mbps, auto‑switching, auto‑negotiating, auto‑discovery, full/half duplex, industry-

standard TCP/IP stack, UDP/IP, CIP, DHCP, SSL, TLS, SSH, SFTP (SSH File Transfer

Protocol), FIPS 140-2 compliant encryption

15 Supply, Installation, testing and commissioning of 16 port switch Nos 1 ₹ 65,500.00 ₹ 65,500.00

Supply Installation Testing and Commissioning of surface-mount USB-to-Dante endpoint,

two-way volume and mute sync for Microsoft Teams,compliant with CE and FCC, device

shouold have Power-over-Ethernet (PoE) to IEEE 802.3af Class 0 standard and support

16 Dante networking using standard CatX cable, device should support the Speakerphone Nos 1 ₹ 1,95,500.00 ₹ 1,95,500.00

profile with and without echo cancellation, enable two-way volume and mute syncronization

with both PC and Mac platforms, Dante with AES67 compliance,Sampling Rate(s) 48

kHz,should be from same OEM as DSP etc complete required as per specifications.

Supply Installation Testing and Commissioning of HDMI Audio Extractor should extract up

to 2 channels of LPCM audio or 5.1 channels of Bitstream audio from an HDMI source,

allowing the user to convert high quality HDMI audio into more convenient analog (LPCM

2.0 sources only) or optical signals for use with powered speakers or non-HDMI AV

receivers. Both the input and output HDMI ports should support 4K UHD resolutions up to

17 4K@60Hz (4:4:4, 8-bit) and should capable of providing high quality audio and video Nos 1 ₹ 93,100.00 ₹ 93,100.00

performance. The unit should supports passthrough of HD and standard Bitstream formats

as well as LPCM 7.1 with audio sampling rates up to 192kHz. Built-in EDID management

support allows the user select from multiple EDIDs and, with the use of optional PC

software, to upload, download, or edit EDID files etc and complete as required

SITC of of Customised Metallic house structure, powder coated with caster wheels & brakes. Drawer

for keyboard, mouse and document camera. Wooden Top Tray for placing document & Laptop. All

drawers sliding tray and doors should be Lockable. External Passive Connectivity: HDMI 2.0 LAN

Cable, Power Socket with ON/OFF. 22”LCD Tablet Monitor with Resolution 1920 x 1080 . View Area

476.64(H) x 268.11(V) ㎜ – 22 inch. Luminance ,White 250 cd/㎡. Colour : 16.7M, Dynamic Contrast

Ratio 50,000:1 . Viewing Angle 85˚+85˚H and 80˚+80˚ V. Lamp Life Time 20,000 Hrs (min ).

Technology Electromagnetic Resonance. Detectable Height 3~10mm. Position Report Rate 138pps.

18 Digital Podium Pressure Resolution 1024 Level. CapacitiveTouch Technology:Projected Capacitive. Detacted object Nos 1 ₹ 2,24,000.00 ₹ 2,24,000.00

Fingers, or Conductive material. Tracking speed : 133<-. single :100:Multy:95. Accuracy : +-0.5mm /+-

3mm (Edge)3mm wide. Detect height 0-10mm. Motorized tilting adjustment for chainging viewing

angle. Minimum 6 Universal rating 5 Amp Socket. Provision to fix Logo at the front side. Provision of

19" minimum 12U Rack inside podium to fit in international standerd equipment. Access doors for

servicing both from front and back side of the podium. Wire manager on left & right side and at

bottom for flexibility of managing additional wire/wiring.

SITC of 450mm Gooseneck microphone with a programmable microphone button (Toggle

Wired on/ off, PTM, PTT, and permanent on) and a bi-color LED ring for status indication. 450mm

19 Gooseneck length, condenser capsule with cardioid pickup pattern, Frequency response: 50 Hz - 20 Nos 1 ₹ 74,000.00 ₹ 74,000.00

microphone kHz, Maximum sound pressure level: 130 dB SPL, Connectivity: XLR 3M. It should have

TTL-logic output for camera control feature

20 HDMI Cable SITC of 3 feet Premium High Speed HDMI 2.0 cable Nos 10 ₹ 4,720.00 ₹ 47,200.00

21 HDMI Cable SITC of 6 feet Premium High Speed HDMI 2.0 cable Nos 15 ₹ 5,310.00 ₹ 79,650.00

22 HDMI Cable SITC of 15 feet Premium High Speed HDMI 2.0 cable Nos 5 ₹ 6,232.00 ₹ 31,160.00

23 HDMI Cable SITC of 10 Meter Active Copper HDMI Cable Nos 0 ₹ 13,338.00 ₹ -

SITC of 6 USB hub Enables 4 computers to share 4 USB 3.2 Gen1 devices Support port

selection via remote controller or RS-422/RS-485 link through 5-pin terminal block

SITC of 10 Meter USB 3.1 Gen1 SuperSpeed Active Extension Cable TypeA/male to

Microphone SITC of Microphone Cable, 2 Conductor 22 AWG PVC Jacket (as per actual) etc all

Cable complete

SITC of 2 Conductor 16 AWG Speaker Cable, PVC jacket (as per actual) etc all

Category 6 SITC of Category 6A Cable, 4 Pair, S/FTP, PVC jacket (as per actual) etc all complete

SITC of 42U, Equipment Rack, with Front glass door, 4 x Fan, 4 Caster wheels, 2 x Shelfs ,

TotalMulty Purpose Hall ₹ 79,90,006.00

AV BOQ for 5th Floor (9 Pax)

SITC of 75" UHD Signage/Professional Display|400 Nits Brightness |40000:1 Contrast Ratio

|Operation: 16x7|1xVGA; 2xUSB 2.0 , 4x HDMI 2.0 In, Secure USB 2.0 (Internal), RJ45,

RJ12, RS232, Optical SPDIF |1xHDMI 2.0 Supports Daisy Chain| Speaker 2x12 W | Open

75" Display With Content Management Support, Scheduler, USB-Autoplay, AutoLaunch, HDMI-CEC, HDMI-

Mini PC Wakeup, Auto-switch on Failover, Panel Lock, OSD Rotation, NoSignalPowerOff, Screen

Saver, Pixel shift, Scheduler, Videowall support, Remote control via LAN, Realtime Clock,

Joystick, Rocker Switch| Optional : OPS compatibility, IR Overlay Touch Compliance

|Certifications: Safety, EMC, CE

Supply, Installation, testing and commissioning of Ceiling microphone with automatic

dynamic Beamforming technology, The beam will automatically detect the position of the

person speaking and will follow the person around the room at all times. It should have 2 x

Dante digital audio (Redundancy), Analog audio out (Phoenix 3-pin), and Ethernet for

Control and PoE connectivity ports. The coverage of the ceiling microphone should be min

800 square feet or more. It should have a true voice lift feature to increase audio

2 intelligibility above the ambient noise floor. It should support IT industry standards like IEEE Nos 5 ₹ 5,10,221.00 ₹ 25,51,105.00

802.1x. It can be controlled through software that can control and monitor the microphone

in any network. It should have min 100 dB SPL, 5ms latency, and min 90dBA or higher

dynamic range. High-precision audio settings for maximum control, setting to exclude (min

5) and prioritize the areas of the room. It should certified from Microsoft Teams and Zoom

Video conferencing applications. It should have UL 62368 certification (including UL 2043

testing and compliance) and safety certifications.

Suppy Installation Testing and Commissioning of digital signal processor with minimum

14no. Or more Mic / line input with phantom power and AEC and 8 or more line level output,

1no. Or more GPIO at least 2 channel of USB input and output for software Video

Digital Signal Conferencing, should have 64x64 channel of digital dante input output, Should have

Processor sampline rate of 48kHz or better, Should be expandable for port expansion, should support

Control with App via iOS and Android devices, or any third-party control system, Shall

have Built-in filters, feedback suppression, AGC single-device(chassis) use is permitted, but

the combination of devices is not accepted etc complete as required as per specifications

Supply, Installation, testing and commissioning of 8 channel energy star rated digital power

amplifier,8 channel at 4 Ohm or 8 ohm energy-efficient amplifier - 8 x 30W or more at

70/100V Technology : Class-D,Input linking through miniature switches, Switching mode

power supply, Protection : DC Short circuit & Over heating & Over load & Signal limiting,

Frequency Response 120 Hz - 20 kHz or better, Silent passive cooling etc complete

required as per specifications.

Supply, Installation, testing and commissioning of 6.5" two-way coaxial thin edge ceiling

loudspeaker having 100V transformer power taps from 60watts to 15watts or better it

should have metal back can for premium performance in demanding applications, Conical

5 Speaker dispersion : 142° or more, Low impedance RMS continuous power of 60watts, impedance : Nos 20 ₹ 23,500.00 ₹ 4,70,000.00

8 or less,frequency range (-10dB) : 70 Hz - 20 kHz, frequency response (±3dB) : 100Hz -

20KHz, Max SPL on 100v should be 105dB or more etc complete required as per

specifications.

7 Mute Buutom Suppy Installation Testing and Commissioning of mute control button Nos 5 ₹ 75,700.00 ₹ 3,78,500.00

Supply, Installation, testing and commissioning of HDMI RX extender with complies with the

advanced HDCP 2.2 and HDMI 2.0 standards, uncompressed HD audio and video as well

as control via a single run of Cat.5e/6/7 cable over distances of up to 70 meters and upto

40mat 4K, HDBaseT feature support: HD Video and Audio, and Control (IR/RS-232 pass-

through) and CEC bypass, Supports pass-through of many audio formats including LPCM

(up to 8 channels), Bitstream and HD Bitstream

Supply, Installation, testing and commissioning of HDMI TX extender complies with the

advanced HDCP 2.2 and HDMI 2.0 standards, uncompressed HD audio and video as well

as control via a single run of Cat.5e/6/7 cable over distances of up to 70 meters and upto

40mat 4K, HDBaseT feature support: HD Video and Audio, and Control (IR/RS-232 pass-

through) and CEC bypass, Supports pass-through of many audio formats including LPCM

(up to 8 channels), Bitstream and HD Bitstream

Supply, Installation, testing and commissioning of wireless presentation device which

should have following features Wireless content input up to 1080P, HDMI 2.0 output,

should Support native wireless mirroring protocols like Airplay, Miracast, Chromecast should

wireless Support plug-n-play HDMI/Type-C/U disk dongles for wireless connection, Support

presentation Windows APP for wireless connection (MAC APP will be available soon), Support 4 split

screen view, Support wireless touch back on interactive whiteboard/touch screen, Best-in-

class data security with dual network and high standard encryption, PoE supported, saving

PSU when connecting with PoE ethernet switch

11 Supply, Installation, testing and commissioning of 16 port switch Nos 5 ₹ 65,500.00 ₹ 3,27,500.00

Supply, Installation, testing and commissioning of Cable cubby (1 HDMI, 1LAN,1 Charging

13 Network Rack 12U AV equipment rack Nos 5 ₹ 19,500.00 ₹ 97,500.00

Supply Installation Testing and Commissioning of Full HD PTZ Camera supporting 1080p

at 60 Frames per Second, minimum 12X Optical Zoom with FoV of 72 degree and

minimum 255 presets. Camera should support simultaneous outputs through HDMI, USB

15 Camera 3.0, IP/3G-SDI, Audio In and can be controlled via RS232/422 and IP. Panning angle -170° Nos 5 ₹ 3,55,600.00 ₹ 17,78,000.00

~ +170° , Tilting angle -30° ~ +90. Camera should support SRT, PoE & should be

compatible with Virtual USB Driver. OEM should be BIS, CE, Clickshare, RoHS & FCC

Certified with test lab report supporting the certifications.

Supply, Installation, Testing & Commissioning of Processor which can enable Voice

Tracking through PTZ Cameras integrated with Ceiling Tiles on IP. The Processor should

16 Tracking Device be capable of connecting minimum 4x Ceiling Tiles with 4x IP based PTZ Cameras for Nos 0 ₹ 3,85,900.00 ₹ -

Quadview output and Auto Switching . The processor should have USB 3.0 Output for Soft

VC. Quoted model should be BIS, CE, FCC & RoHS Certified with Test Lab Reports.

17 Audio Cable Supply, installation, testing and commissioning of of Stereo Audio Cable Mtr 100 ₹ 550.00 ₹ 55,000.00

Supply, installation, testing and commissioning of of 2.5 Sqmm x 2 core ATC copper

Conductor, Insulated Cores,PVC Sheathed Speaker Cables .

19 HDMI Cable Supplying and laying HDMI Cable with connector on both ends. Mtr 100 ₹ 910.00 ₹ 91,000.00

20 USB Cable Supplying and laying USB Cable with connector on both ends. Mtr 40 ₹ 525.00 ₹ 21,000.00

Total Meeting Room 5 Qty ( 9 Pax) ₹ 1,41,94,605.00

AV BOQ for 4th Floor (11 Pax)

SITC of 86" UHD Signage/Professional Display|400 Nits Brightness |40000:1 Contrast Ratio

|Operation: 16x7|1xVGA; 1xDP, 2xUSB 2.0 , 4x HDMI 2.0 In, Secure USB 2.0 (Internal),

RJ45, RJ12, RS232, Optical SPDIF |1xHDMI 2.0, 1xDP Out|Supports Daisy Chain| Speaker

85" Display With

1 2x12 W | Open Content Management Support, Scheduler, USB Autoplay, AutoLaunch, Nos 4 ₹ 4,10,000.00 ₹ 16,40,000.00

HDMI-CEC, HDMI-Wakeup, Auto-switch on Failover, Panel Lock, OSD Rotation,

NoSignalPowerOff, Screen Saver, Pixel shift, Scheduler, Videowall support, Remote control

via LAN, Realtime Clock, Joystick, Rocker Switch|

Supply, Installation, testing and commissioning of Ceiling microphone with automatic

dynamic Beamforming technology, The beam will automatically detect the position of the

person speaking and will follow the person around the room at all times. It should have 2 x

Dante digital audio (Redundancy), Analog audio out (Phoenix 3-pin), and Ethernet for

Control and PoE connectivity ports. The coverage of the ceiling microphone should be min

800 square feet or more. It should have a true voice lift feature to increase audio

2 intelligibility above the ambient noise floor. It should support IT industry standards like IEEE Nos 4 ₹ 5,10,221.00 ₹ 20,40,884.00

802.1x. It can be controlled through software that can control and monitor the microphone

in any network. It should have min 100 dB SPL, 5ms latency, and min 90dBA or higher

dynamic range. High-precision audio settings for maximum control, setting to exclude (min

5) and prioritize the areas of the room. It should certified from Microsoft Teams and Zoom

Video conferencing applications. It should have UL 62368 certification (including UL 2043

testing and compliance) and safety certifications.

Suppy Installation Testing and Commissioning of digital signal processor with minimum

14no. Or more Mic / line input with phantom power and AEC and 8 or more line level output,

1no. Or more GPIO at least 2 channel of USB input and output for software Video

Digital Signal Conferencing, should have 64x64 channel of digital dante input output, Should have

Processor sampline rate of 48kHz or better, Should be expandable for port expansion, should support

Control with App via iOS and Android devices, or any third-party control system, Shall

have Built-in filters, feedback suppression, AGC single-device(chassis) use is permitted, but

the combination of devices is not accepted etc complete as required as per specifications

Supply, Installation, testing and commissioning of 8 channel energy star rated digital power

amplifier,8 channel at 4 Ohm or 8 ohm energy-efficient amplifier - 8 x 30W or more at

70/100V Technology : Class-D,Input linking through miniature switches, Switching mode

power supply, Protection : DC Short circuit & Over heating & Over load & Signal limiting,

Frequency Response 120 Hz - 20 kHz or better, Silent passive cooling etc complete

required as per specifications.

Supply, Installation, testing and commissioning of 6.5" two-way coaxial thin edge ceiling

loudspeaker having 100V transformer power taps from 60watts to 15watts or better it

should have metal back can for premium performance in demanding applications, Conical

5 Speaker dispersion : 142° or more, Low impedance RMS continuous power of 60watts, impedance : Nos 16 ₹ 23,500.00 ₹ 3,76,000.00

8 or less,frequency range (-10dB) : 70 Hz - 20 kHz, frequency response (±3dB) : 100Hz -

20KHz, Max SPL on 100v should be 105dB or more etc complete required as per

specifications.

Supply Installation Testing and Commissioning of surface-mount USB-to-Dante endpoint,

two-way volume and mute sync for Microsoft Teams,compliant with CE and FCC, device

shouold have Power-over-Ethernet (PoE) to IEEE 802.3af Class 0 standard and support

6 Dante networking using standard CatX cable, device should support the Speakerphone Nos 4 ₹ 1,95,500.00 ₹ 7,82,000.00

profile with and without echo cancellation, enable two-way volume and mute syncronization

with both PC and Mac platforms, Dante with AES67 compliance,Sampling Rate(s) 48

kHz,should be from same OEM as DSP etc complete required as per specifications.

7 Mute Buutom Suppy Installation Testing and Commissioning of mute control button Nos 4 ₹ 75,700.00 ₹ 3,02,800.00

Supply, Installation, testing and commissioning of HDMI RX extender with complies with the

advanced HDCP 2.2 and HDMI 2.0 standards, uncompressed HD audio and video as well

as control via a single run of Cat.5e/6/7 cable over distances of up to 70 meters and upto

40mat 4K, HDBaseT feature support: HD Video and Audio, and Control (IR/RS-232 pass-

through) and CEC bypass, Supports pass-through of many audio formats including LPCM

(up to 8 channels), Bitstream and HD Bitstream

Supply, Installation, testing and commissioning of HDMI TX extender complies with the

advanced HDCP 2.2 and HDMI 2.0 standards, uncompressed HD audio and video as well

as control via a single run of Cat.5e/6/7 cable over distances of up to 70 meters and upto

40mat 4K, HDBaseT feature support: HD Video and Audio, and Control (IR/RS-232 pass-

through) and CEC bypass, Supports pass-through of many audio formats including LPCM

(up to 8 channels), Bitstream and HD Bitstream

Supply, Installation, testing and commissioning of wireless presentation device which

should have following features Wireless content input up to 1080P, HDMI 2.0 output,

should Support native wireless mirroring protocols like Airplay, Miracast, Chromecast should

wireless Support plug-n-play HDMI/Type-C/U disk dongles for wireless connection, Support

presentation Windows APP for wireless connection (MAC APP will be available soon), Support 4 split

screen view, Support wireless touch back on interactive whiteboard/touch screen, Best-in-

class data security with dual network and high standard encryption, PoE supported, saving

PSU when connecting with PoE ethernet switch

11 Supply, Installation, testing and commissioning of 16 port switch Nos 4 ₹ 65,500.00 ₹ 2,62,000.00

Supply, Installation, testing and commissioning of Cable cubby (1 HDMI, 1LAN,1 Charging

13 Network Rack 12U AV equipment rack Nos 4 ₹ 19,500.00 ₹ 78,000.00

Supply, Installation, Testing & Commissioning of USB 3.2 Extenders. Transmitter should

have 1xUSB C input port, 1X RJ45, 1xUSB-A Output Port. Receiver should have Input Port

14 USB Tx Rx 1×Cat5e/6A/7 (RJ45). 1×USB-C, 3×USB-A Output Port. Bandwidth upto 5Gbps Nos 4 ₹ 96,000.00 ₹ 3,84,000.00

(SuperSpeed), Tranmission distance upto 100M. Devices should be controlable by the USB

host on a transmitter. Should have backward compatibility with USB 2.0

Supply Installation Testing and Commissioning of Full HD PTZ Camera supporting 1080p

at 60 Frames per Second, minimum 12X Optical Zoom with FoV of 72 degree and

minimum 255 presets. Camera should support simultaneous outputs through HDMI, USB

15 Camera 3.0, IP/3G-SDI, Audio In and can be controlled via RS232/422 and IP. Panning angle -170° Nos 4 ₹ 3,55,600.00 ₹ 14,22,400.00

~ +170° , Tilting angle -30° ~ +90. Camera should support SRT, PoE & should be

compatible with Virtual USB Driver. OEM should be BIS, CE, Clickshare, RoHS & FCC

Certified with test lab report supporting the certifications.

Supply, Installation, Testing & Commissioning of Processor which can enable Voice

Tracking through PTZ Cameras integrated with Ceiling Tiles on IP. The Processor should

16 Tracking Device be capable of connecting minimum 4x Ceiling Tiles with 4x IP based PTZ Cameras for Nos 0 ₹ 3,85,900.00 ₹ -

Quadview output and Auto Switching . The processor should have USB 3.0 Output for Soft

VC. Quoted model should be BIS, CE, FCC & RoHS Certified with Test Lab Reports.

17 Audio Cable Supply, installation, testing and commissioning of of Stereo Audio Cable Mtr 100 ₹ 550.00 ₹ 55,000.00

Supply, installation, testing and commissioning of of 2.5 Sqmm x 2 core ATC copper

Conductor, Insulated Cores,PVC Sheathed Speaker Cables .

19 HDMI Cable Supplying and laying HDMI Cable with connector on both ends. Mtr 100 ₹ 910.00 ₹ 91,000.00

20 USB Cable Supplying and laying USB Cable with connector on both ends. Mtr 40 ₹ 525.00 ₹ 21,000.00

Total Meeting Room 4 Qty ( 11 Pax) ₹ 1,29,07,684.00

Total Audio-Video ₹ 6,62,67,704.00

SCHEDULE OF QUANTITIES - CCTV WORKS

S NO DSR/MR DESCRIPTION QUANTITY UNIT RATE DSR AMOUNT NDSR AMOUNT

SITC of as per specifications of this and directions of Engineer-in- Charge .2MP Dome Camera • 1/2.8” Low

Illumination Progressive Scan CMOS Sensor • Quad Streaming • Multiple compression techniques

H.265/H.264/MJPEG • Support 3D digital, HLC, WDR • Support bi-directional Talk • IP67 Complaint • OWASP Rev. 4.0

Level 2 Cyber Security Certified by STQC Technical Specifications: Image sensor 1/2.8”, 2MP Low Illumination

Progressive Scan CMOS Sensor, Effective Pixels 1920(H)X1080(V) ,Aspect Ratio 16:9 ,Min. Illumination Color:

0.001Lux @ (F1.2, AGC ON), 0.014 Lux @ (F1.4, AGC ON), 0 Lux with IR, S/N Ratio ≥58dB (AGC OFF), IR Distance

20-30Mtr, Shutter Speed Auto, Slow Shutter, (1/5 sec ~ 1/100,000 sec Adjustable), Slow Shutter On/ Off,WDR Up to

120 dB, TWDR (Off/ Low/ Middle/ High),IR LED Control Auto, Manual, OFF, 3D DNR Low, MID-Low, MID, MID- HIGH,

High, Day/Night ICR switch, Auto, Color, B&W, External Trigger, Defog Off, Low, Middle, High, Output PAL/NTSC

adjustable, Lens Type 2.8-12mm Motorized Zoom Lens ,IRIS Control Auto , Mount Type M14, Focus Control

Auto/Manual, Compression H.265/H.264/MJPEG, H.265 Encoding Main Profile, H.264 Encoding Baseline / Main Profile

/ High Profile, Streaming Capability Quad Streams, Resolution 2MP/720P/VGA, Streams Mainstream: 2MP

(1920X1080)@25/30fps Sub Stream: 720P (1280X720)@25/30fps Third Stream: VGA(640x480)@15fps Fourth

Stream: VGA(640x480)@15fps, Frame Rate 1~ 30fps,Video bit Rate Constant bit rate, variable bit rate (16kbps-

8Mbps), I - Frame 2 -255, Color Mode Normal, Bright, Nature, Exposure Mode Off, High Light correction, Backlight

Correction, Range (1-10), BLC Mode 1-10 configurable Levels, White Balance Auto, Manual, Warm light, Natural light,

Incandescent lamp, fluorescent lamp, Locked WB, Gain Control Low, MID-Low, MID, MID- HIGH, High, Sharpness 0-

255 ,Network Port RJ45 10M, 100M Network Self Adjustable , Protocol TCP/IP, IPv4, IPv6, SSL, TLS, UDP,

HTTP/HTTPS, HTTP-Base64, HTTP-Digest, DHCP, DNS, RTP, RTSP , NTP, SMTP, IGMP, Multicast,Audio Built-In-Mic

or 1 IN/1 Out ,Alarm 1Ch Alarm IN, 1Ch Alarm Out, SD Card Yes, Up to 256GB, Surge Protection TVS 4000V Lightning

Protection, Surge Protection & Voltage Transient Protection, Power supply DC 12V ± 10% / PoE (802.3af), Power

Consumption <12W, Dimension & Weight 135mm(H) x140mm(L) x 140mm(W), 630 g, Product Certification Safety:

CE, FCC, EN:60950-1, IS 13252 (Part 1):2010, BIS Registered EMC & Immunity: CE, FCC Cyber Security: ISO/IEC

27400 OWASP Level 2 of ASVS v4.0 Appendix C Certificate No. STQC/IOTSCS/0922/001U1 Reliability Certification:

MTBF >1,00,000 hours at 40°C as per specifications of this and directions of Engineer-in- Charge

Supply, Installation, Testing & Commissioning of Recorning Server as per technical specification with 100TB.

Supply Installation Testing Commissioning of VMS Base license as per specifications of this tender etc complete as

required and directions of Engineer-in- Charge.

Supply Installation Testing Commissioning of VMS camera license for recording.playback live view and event search

as per specifications of this tender etc complete as required and directions of Engineer-in- Charge.

Supply Installation Testing Commissioning of LED Display 55" Smart LED TV 138 cm/ 55" colour Ultra HD (4k),

professional/commercial monitor having 24 X 7 operation, with USB Port 2, HDMI Port 3, HDMI (ARC), 2 channels, 20

5 MR W Speaker output power, AC4 audio format, Stream content from devices, Wifi facility, dolby digital plus surround 1 Nos 95,000.00 0.00 95,000.00

sound technology i/c making connection, testing etc. complete as required. as per specifications of this tender etc

complete as required and directions of Engineer-in- Charge.

SCHEDULE OF QUANTITIES - ACESS CONTROL WORKS

S NO DESCRIPTION QUANTITY UNIT RATE NDSR AMOUNT

Supply, installation, testing and commissioning of Enterprise level Application including Time Attendance-Access Control, GUI,

Antipass back, Reports in Inbox, with Unlimited Users, Door Scheduling, Unlimited Client logins, Event Notification, POP ups, Mustur

Points, Area Control, Time base access and alerts. AI Dashboard for People Counting,, Occupancy Manager, Software should be

VAPT approved and should provide per reader license, Sofware should expandable and scalable and have capability in future

integration of Elevator management, Template management and card priting ,Integrated credential issuance application inclusive of

card template designing, card printing, finger print enrollment, key management, contactless card reader/writer & contact card

reader/writer, Software shall support Access IP and Interface Controllers & Card Readers, Biometric Readers & Enrolment Devices,

Card Printers, Card Encoding Devices, Smart Cards, Mobile/Digital Credentials, BLE/NFC based access readers,Flap Barrier, Boom

Barrier etc, §Software Login shall be secured by providing a strong password implementation policy, enforcing strong passwords with

minimum/maximum limits, use of upper-case & lower-case characters, and numeric, and special characters. It shall also support

policy for password expiry, portal lockout, audit trails, use of captcha etc. Server Browser communication shall be secured using

Hypertext Transfer Protocol using Secured Sockets Layer [HTTPS (SSL)]. Server Application Security shall be ensured by

developing the software according to ISO 27001 Standards or Information Security & Management Systems (ISMS). Further, it shall

be certified for any Vulnerability Assessment & Penetration Testing (VAPT) by a recognized 3rd party testing authority. GDPR,

SOC1,SOC2 & ISO20018 compliant. Access Controllers to server communication channels shall be secured using TLS or AES 256

Bit Encryption. Access Controllers shall have IPV4/IPV6 (greater connection integrity and security), SNMPv3/ v2c, centralized

biometric template management, Cryptographic module, like OpenSSL FIPS Object Module RE, Crypto memory chip for Biometric

Templates, credential & user info, DIP Switch Toggle sets 5 minutes to disable web page access, Strong Password Enforcement (8-

64 characters), HTTPS secured web interface for configuration. Access Controllers to Subordinate devices like door modules, Input &

output modules shall be secured by using AES256-bit Encrypted RS485 Channel. Reader to Controllers/Door Module communication

channel shall be secured using ODDP Secured Channel (SC) Communication. Readers shall have Secured Elements &

Cryptographic Operations for the protection of Card reader keys. Card/Credential to Reader communication shall be on 13.56 Mhz

Radio Frequency deployed with Symmetric Key Encrypted Data Transmission. Card/Credentials shall have encryption key-based

secured user memory access.as per specifications of this tender etc complete as required and directions of Engineer-in- Charge.

Supply, Installation, Testing & Commissioning of Integrated Visitor Managment System a.Mandatory fields for visitor pass issue

b. Whether appointment is must for every visitor

c. Whether Access Card issue to visitor is compulsory

d. Whether visitor request to be approved by the group administrator

e. Whether Email based approval

f. Sending of Email/SMS to the approved visitor

g. Sending Email/SMS to the employee on visitor arrival

2 MR h. Pop up on Employee’s system on visitor arrival 1.00 Nos 2,95,000.00 2,95,000.00

i. Banned visitor notification

j. Lapse Time (Time after which appointment will get expired)

k. Default Departure Hours (if some other time is not set)

l. Pre Appointment hours ( Time before the scheduled appointment during which pass can be generated). as per specifications of this

tender etc complete as required and directions of Engineer-in-Charge.

Supply, Installation, Testing & Commissioning of Access IP Controller with Enclosure and Power Supply Unit : 2 Door 4 Reader with

RS485 OSDP, Security Features: Authorized IP address filtering, IP Client Proxy Host communications protected by TLS 1.2/1.1 or

AES 128/256 bit data encryption for optimal data protection, Crypto memory chip, IO Expansion connection protected by AES

Capacity: Cards/Users : 240000 Offline Event Log: 5,0000 & Communications Built in TCP/IP, IPV4, IPV6, RS-485, Inputs: Seven

unsupervised/supervised, Two unsupervised dedicated for cabinet tamper and UPS fault monitoring, Outputs: Four relays, Power :

12 to 24 Vdc 10 %, 500 mA maximum , Supports up to 520 inputs and 516 outputs, 16 card formats per active reader, 8 per offline

reader, Open Supervised Device Protocol (OSDP) and OSDP SC compliant, Anti-passback support, Area-based, reader-based, or

Nested area, hard, soft, or timed forgiveness, Encrypted database, Supports up to nineteen (19) digit card numbers, Intrusion Alarm

Functions: Area monitoring, Standard alarm masking , Fire Integration; open all doors from hardware itself, Temperature:

-55 to +85 °C, storage, 0 to +70 °C, operating, Humidity: 5 to 85 % RHNC, Micro USB Port, SD card upto 8 GB. Certifications and

Compliances:UL294 Recognized, FCC Part 15 Subpart B, CE Compliant, RoHS, NIST Certified Encryption etc. as per specifications

of this tender etc complete as required and directions of Engineer-in- Charge.

Supply, Installation, Testing & Commissioning of Face Reader with RFID read 13.56 Mhz Frequency Mifare Reader capacity,

Display: 5” WVGA (480x800) color touch screen, Hardware platform: CPU: 5 Cores + NPU,RAM Memory: 4GB,Flash Memory:

16GB, Operating system: Linux ,Face Optics &amp; Sensors: 2 x Cameras for RGB / RG-IR, Resolution 2MegaPix, Lens Field of

View : 55 x 90°, 3D stereovision, NIR Illumination LEDs, White illumination LEDs,sensor for presence detection, RFID Card: Mifare

Classic/Desfire EV0/Desfire EV1 etc. Sounds: Buzzer, Electrical Interfaces, PoE+ compatible, Input voltage: 12 - 24 VDC, 36W

minimum, Environmental Operation: Operating temperature: 14° to 113°F (-10° to +45°C), Operatin, humidity: 10 - 80% (non-

condensing), IP65 rating for dust and water jet exposure, IK07 for impact protection, except screen, Data privacy and security, Device

shall be 100% complied to GDPR, All face images shall be stored in form of template propriety of OEM for Security and Theaft

reasons, Housing Material: ABS/PC, All date shall be stored with 256 Bit AES encryption only, Privacy:Bio Template should be

encrypted using OEM proprietary encryption to prevent the conversion of

template to raw image,The face Template capture should be in 3D (Using Hardware or Software algorithm), In case of tamper, all

4 MR biometric data should be erased hence to prevent the data theft , Template should be encoded to smart card with personalized keys 31.00 No. 95,000.00 29,45,000.00

to safeguard personal data, Devices should also support both Template on device and Template on card, No raw image shall be

stored inside the device, Security: For Any data exchange devices shall use : TLS v1.3 and will avoid TCP/IP connection to prevent

unauthorized access over network, Hash algorithms SHA2 or above, Devices and Application service shall establish connection over

SSL end points, device and server will use SSL certificate for handshaking, All bio devices shall be immune to cyber security threat by

inbuilt Anti Hacking measures, Crypto chip, secure booting &amp; authenticity check ,TLS by default, 802.1.X network authentication,

Performance: The face algorithm must be NIST evaluated for benchmarking, accuracy &amp; fairness. Biometric face terminal

cameras to acquire visible, infrared and stereovision of user face for best of

performance, Face Algorithm and device shall be of same make for best or performance, longevity and accuracy. The device should

use GPU or NPU processor for best of speed., The device should also use AI and ML to adopt the changes of skin due to aging,

injury and other reasons. Certifications: CE, CB, FCC, UL294, RoHS, California Proposal 65, REACH and WEEE compliant, All the

certifications shall be latest and valid as per Goverment norms. and copy of certificates shall be provided along with technical bid etc.

Supply, Installation, Testing & Commissioning of Smart card Frequency Excitation (13.56 MHz) Mifare smart Card , distance upto

2.5" Memory Type EEPROM, 2K bit memory Complies with ISO/IEC standards for thickness. Lifetime Warranty .etc. as per

5 MR specifications of this tender etc complete as required and directions of Engineer-in- Charge. The card should work in the existing 100.00 No. 324.50 32,450.00

office of OIL India Noida also and should be compatible with the existing system

Supply, Installation, Testing & Commissioning of Press to Exit Push Button Stainless Steel Heavt duty Stainless Steel NO, NC based

etc. as per specifications of this tender etc complete as required and directions of Engineer-in- Charge.

Supply, Installation, Testing & Commissioning, Emergency Glass Break Unit Single Pole NO, NC Contact, Green/Red/White Color

options shall be availble as per specifications of this tender etc complete as required and directions of Engineer-in- Charge.

Supply, Installation, Testing & Commissioning of Single Leaf Electro Magnetic Lock as per door design, Fail safe type, Holding

force: 272kg(600lbs), Inbuilt Door contact , Current Drain:320mA/12VDC, Built-in voltage spiker suppressor to protect the lock body

Supply, Installation, Testing & Commissioning of Double Leaf Electro Magnetic Lock as per door design, Fail safe type, Holding

force: 272kg(600lbs), Inbuilt Door contact , Current Drain:320mA/12VDC, Built-in voltage spiker suppressor to protect the lock body

9 MR and equipments, lock body and armature with chemical plating anticorrosion finished, With LED light & brackets CE Certified, etc.as 14.00 No. 15,110.00 2,11,540.00

per specifications of this tender etc complete as required and directions of Engineer-in- Charge.

Supply, Installation, Testing & Commissioning of 8 core .75 Sqmm Copper Flexible shielded RS485 OSDP communication multi-

10 MR stand Data Cable etc. all complete as per tender specs. as per specifications of this tender etc complete as required and directions 750.00 Mtr 195.00 1,46,250.00

of Engineer-in- Charge.

Supply, Installation, Testing & Commissioning of 4 core.75 Sqmm Copper Flexible shielded communication multi-stand Data Cable

etc. as per specifications of this tender etc complete as required and directions of Engineer-in- Charge.

Supply, Installation, Testing & Commissioning of 3 core 1.5 Shielded communication multi-stand Data Cable etc. as per specifications

of this tender etc complete as required and directions of Engineer-in- Charge.

Supply, Installation, Testing & Commissioning of Server i7-7700T 2.9GHz Processor. Turbo max to 3.8GHz • Support Intel vPro,

13 MR AMT 11 remote management • Support TPM 2.0 Function • up to 4 x 2.5" SATAIII Storages,as per specifications of this tender etc 1.00 Nos 1,69,658.00 1,69,658.00

complete as required and directions of Engineer-in- Charge.

SCHEDULE OF QUANTITIES: FIRE ALARM & PA SYSTEM

S No DESCRIPTION OF ITEM UNIT QTY RATE DSR AMOUNT NDSR AMOUNT

FIRE ALARM SYSTEM (ADDRESSABLE TYPE)-

Supply, Installation, Testing and Commisioning UL listed and FM approved of addressable

Analog 4 loop Fire Alarm Panel shall be running on full digital protocol with 32 bit

Microprocessor based 8 Loop panel , Networkable analogue addressable type Fire Alarm

Control Panel . The Panel shall be complete with 6" color liquid-crystal display (LCD). LCD

Display status highlights Alarm events appear in red; Trouble events appear in yellow;

Supervisory events in blue, and Security events in magentay. System should be capable to

have 2500 intelligent initiation devices per panel. Each addressable loop shall be capable

of not less than 250 addresses per loop configuring either as all detectors or modules or any

mix of both. The panel shall have the Fire Fighter Touch Screen Graphical Display panel to

1.0 inform & guide Fire Fighter for carring out Fire Fighter operation. The display shall have Set 1 8,19,247.50 0.00 8,19,247.50

Hazmat icons indicating the presence of explosive gas, liquids, poison,fumes etc . To

expedite system troubleshooting, the system cards shall have ground fault detection and

diagnostic LEDs by card. In the display,simple building floor plan can be loaded in bitmap or

jpeg format, On the map, the user will see an icon indicating the location of the event in the

building in addition to a 'You-Are-Here' symbol to tell the responding person exactly where

they are in the building in relation to the event. The system shall be polarity insensitive. The

panel shall support degrade mode operation and shall have battery backup of 24 hrs in

normal condition and 30 minutes in Alarm condition

Supply of UL Listed and FM approved Repeater Panel. The panel shall be able to give

location of all fire and fault and Isolation conditions of addressable units of main Fire Alarm

panel via the address codes. Panel shall have feature to Acknowledge/Slience/Reset.

The panel shall have a LCD display and having maximum 160 (4 x 40) Characters in the

SITC of UL268 6th and 7th edition compliance and FM approved Intelligent Addressable

multi-criteria detector (optical and thermal sensors) for true ceiling complete with standard

base, facility to mount in different comprehensive environment, Tri-color detector-status LED

with 360 ° view, microprocessor circuitry with error check; detector self-diagnostics and

supervision programs,Rate-of-Rise Detection: 15°F / min. (8.3°C / min.) - Fixed: 135°F

3.0 (57°C) , Field programmable as rate-of-rise or fixed temperature, Polarity insensitive, Nos. 330 3,951.00 0.00 13,03,830.00

Superior EMI and RFI immunity, RoHS compliant. Detector shall have in-built isolator for

better reliability, circuit integrity and advanced fault finding. Manufacturers not having in-built

Isolator feature in detector shall consider Isolator base in place of standard base OR

separate Isolator before and after every detector to comply the same without any extra cost.

Digitally signed by

PRADYUMNA MUKHERJEE

SITC of UL268 6th and 7th edition compliance and FM approved Intelligent Addressable

multi-criteria detector (optical and thermal sensors) for False ceiling complete with standard

base, facility to mount in different comprehensive environment, Tri-color detector-status LED

with 360 ° view, microprocessor circuitry with error check; detector self-diagnostics and

supervision programs,Rate-of-Rise Detection: 15°F / min. (8.3°C / min.) - Fixed: 135°F

4.0 (57°C) , Field programmable as rate-of-rise or fixed temperature, Polarity insensitive, Nos. 300 3,951.00 0.00 11,85,300.00

Superior EMI and RFI immunity, RoHS compliant. Detector shall have in-built isolator for

better reliability, circuit integrity and advanced fault finding. Manufacturers not having in-built

Isolator feature in detector shall consider Isolator base in place of standard base OR

separate Isolator before and after every detector to comply the same without any extra cost.

Supply, installation, testing and commissioning Intelligent Addressable microprocessor

based, rate of rise and fixed temperature Heat detector with base.Provides seven (7) field-

selectable settings in the 135° − 174°F (57.2° − 78.9°F) temperature range and can be

configured to provide a low-temperature warning signal at 40°F (4.4°C). Tri color LED,

5.0 Green for Normal, Amber /yellow for trouble and Red for alarm. Detector shall have in-built Nos. 7 3,638.70 0.00 25,470.90

isolator for better reliability, circuit integrity and advanced fault finding. Manufacturers not

having in-built Isolator feature in detector shall consider Isolator base in place of standard

base OR separate Isolator before and after every detector to comply the same without any

Supply Installation, Testing & Commissioning of UL listed Intelligent addressable control

module with built-in isolator , shall meet Class X (Style 7) survivability requirements . Shall

6.0 have multi-color light-emitting diode (LED) which indicates system status Green, Amber and Nos. 30 7,485.30 0.00 2,24,559.00