Loading
Loading…
Loading…
6,759 results • Best match
Number writing on equipment with fluorescent striker an fluorescent base at different place in 05 HEMMs(S3, S7, S10, IR7 and IDM9) also at board of 08 nos. rooms (Dozer, Drill, LnT, electrical and four spares rooms) at Ashok OCP at Piparwar Area.
Repairing of both side 54 numbers hole of boss sprocket and Repairing of damaged front and rear belly guard by gas cutting of plates, straightening by gas heating and hammering, cracked portion V groove cutting and welding of D155 Dozer Sl NO 1
Repairing of LHS yoke shaft and removal of broken bolt of Karm joint , fabrication if rear till guard mounting based and slightly of balde eyes (lift Cylinder) and fabrication of pins etc of BD355 Dozer SL.No. 11998 of Kuya OCP, Bastacolla Area IX.
Repairing of AC compressor and evaporator coil with replacement of copper tube, AC high pressure hoses and low pressure hoses with end fitting, complete gas charging and fitment of all item of Dozer BD-155, Sl. No. - 13781 at AKK OCP ,BnK
Minor denting and fitting of Operator cabin safety glass along with rubber bit and key and Repairing and fitting of Operator Seat and back rest in BD-355 Dozer Sl. No. T-11722, T-11723, T-11654 and T-11890 of Kathara Colliery.
Repairing of LHS and RHS brake drum replacement from serviceable assly, removing blade stabilizer rod broken bolt material filling and fitting new bolt 4 nos. as per size with welding supporting plate of Dozer Sl. No. T-11971 of Konar Expansion, BnK.
Dismantling and erection of 6point6KV overhead line to feeding power to HEMM machine at SOCP patch extension of LT 220volt overhead line at haul road for proper lighting purpose from dozer section to new face and dismantling of idle overhead line of
Repairing and replacement of under carriage , repairing/ rebuilding of worn out and broken lower portion of blade for fitting cutting edges and end bits and extra plate welding on blade and denting and painting of Dozer model- BD- 355, Sl. No.G-115
Repairing and fabrication of operator cabin assy. Operator cabin glass, engine trans guards, stairs of Cat 16G Grader Sl.No G2 Repairing of foot plate, tilt guard , 54 nos. sprocket holes, both side track chain of D355 dozer D21 of Ashoka PPR Chatra
Repairing of Front Spindle of BEML make BH60 M Dumper Sl. No. D-60407 and Repairing of Mount Base of cutting Edge and end bit and repairing Sprocket Assly Eye Hole and cutting / welding Sprocket Guard of Dozer T-13617 of Sirka Project.
Repairing of O/P cabin mountings, engine hood, side plates, steering tie rod mountings, UJ assy and flange, foot plate both side tilt cylinders steel pipe, engine and transmission guard tilt guard of D355 Dozer Sl.No. D21 of Piparwar patch, at Asho
Repairing of hoist drum assy. etc. of EKG5A shovel 562, repl. of complete undercarriage etc. of REL C-650D drill 708 and repairing of 03 Nos. radiator BD355 dozer 11906, IDM30 drill 852, and REL C-650D drill 708 of Urimari OCP.
REPAIRING OF BOTH SIDE CYLINDER (130TF53482) AND CHANGING OF WORN OUT TRACK CHAIN LINK, PIN AND BUSHING 02 NOS., REPAIRING OF BOTH SIDE TUNION CAP AND TUNION BALL, REPAIRING OF DASHBOARD OF D355 DOZER SI. NO.-11983 OF DAMODA COLLIERY, BARORA AREA.
Rep. of lift cylinder both side by changing of seal kit, bush and material filling near eye portion and grinding, repairing of Radiator assembly along with new radiator guard making and rep. of exhaust system with silencer rep. of BD-355 Dozer-11648
Repairing/reconditioning of Air Conditioner System and filling of Refrigerant of 04 Nos. Dumper SI No. 60394, 60397, 60428, 60430, 06 nos. Dozer Sl. No. 13584, 13589, 13639, 13721, 11970, and 11646 and 02 nos. Water sprinkler, Sl. No. 28113 and 28132
Dismantling of Track Chain, Carrier Roller Foundation, Idler removal of broken Yoke Shaft and Fitting of new Yoke Shaft after modification and rep. and Changing of worn out Track Chain Link 04 nos. of BD-355A Dozer, Sl. No.- G11561 of AMP coll.
A) Rep /new making of LHS and RHS track chain guard both side B) For extracting old LHS track chain link , pin cutting , opening fitting and carrier roller foundation and broken bolt removal and LHS equalizer seat welding of Dozer Sl.No.11670
Repairing of track frame (LH and RH) and final drive drum blade assly. blade arm, triunion, Diagnal, End bi, cutting edge and center plate of BD-355 Dozer Sl. No. 11580 of Kedla Open Cast Mine Project (KOCP) deployed at Kedla Washery
Repairing of operator cabin ceiling, mountings, op seat, LHS RHS gate, both side cylinder eye,etc of 12XW Cr4 and Repairing of Both side Lift cylinder eye, Engine hood, exhaust system, side plate covering engine, foot plate,etc of D355 dozer D22
REPAIRING OF BOTH SIDE CYLINDER (130TF53482) AND CHANGING OF WORN OUT TRACK CHAIN LINK, PIN AND BUSHING 02 NOS., REPAIRING OF BOTH SIDE TUNION CAP AND TUNION BALL, REPAIRING OF DASHBOARD OF D355 DOZER SI. NO.-11662 OF AMP COLLIERY, BARORA AREA.
Repair work on the engine and transmission oil cooler, including dismantling, fitment, and replacement of the air seal and bolts, repair of the seat and blade arm joint ball stud with material filling, and fabrication of the A-frame for Dozer Sl. No.
REPAIRING OF RHS TRACK CHAIN, CARRIER ROLLER FOUNDATION, IDLER FOR REMOVAL OF BROKEN YOKE SHAFT AND FITTING OF REPAIR YOKE SHAFT AND CHNAGING OF WORN OUT TRACK CHAIN LINK, PIN AND BUSHING 04NOS. OF DOZER SL.NO.11662 OF AMP COLLIERY BARORA AREA.
Fitting of safety glass in BH60M Dumper 61150 (LHS glass), and BE1000-1 Hyd. Shovel Sl. No. G10228 and G10121 of operator Hyd. Shovel G10121, Water Sprinkler SWS-28236, Drill No. 817 and BD355 Dozer G11389 E12046 at Bansdeopur OCP, Sija Area.
Change of 02 nos. old and serviceable track chain and cutting of 02 nos. link pad and replacing it with old and serviceable 02 nos. link and pad with partial repairing of 01 no. idler assembly of Dozer E12044 at ADIC Kusunda Area
Repair of track pads, pins and replacing with serviceable track pads, rebuilding of pivot shaft by material deposition and making of 24 no holes, pivot shaft chassis housing by machining and line boring and pressing of 06no. Bushes, etc of D3 Dozer
For Repairing of LHS and RHS Sprocket boss hole and LHS and RHS carrier roller foundation, Equalizer seat and LHS and RHS track frame and repairing LHS Track chain link pin cutting welding of Dozer Sl. No.- 11994 at AKWMOCP, Katras Area BCCL.
repair, maintenance n rewiring of the control panel of the 2 Nos. overhead crane (Hoist 10 Ton capacity) and complete repairing and rewinding of the induction motor sl. Nos. -11223108, KW18.5, 415v, 970 RPM, of Rajrappa Washery Project.
Repairing of cracked chassis arm by welding and line boring (02 nos.), new fabrication and fitting of bush (04 nos.) and center pin (02 nos.) of RT630C Crane sl.no. 404324 at Nichitpur OCP of Sijua Area.
Repairing / replacement of differential system, rear wheel hub, repairing of gear box housing, replacement of clutch plate and bull pinion shaft and repairing of steering cylinder of ACE XW-12 ton Crane of Gidi-A project.
For repairing and straightening and aligning and welding of glass frame and new safety glass fitting and operator seat base and back rest changing of ACE Crane SL.NO. 189757( JH10AM-2980) at AKWMOCP, KATRAS AREA, BCCL
Repairing of 01 No. air compressor, center pin hole of main frame and cradle base, tray steering cylinder eye hole, cradle base eye hole of ACE crane Sl. No. JH10BB 2715 at Nichitpur OCP, Sijua Area
Repair of upper and lower hitch articulation assembly housing, line boring bearing replacement etc of L1 Loader and LHS and RHS outrigger steel tube , UJ assy., propeller shaft etc of C12 Crane at Ashok OCP.Refer NIT.
Maintenance of EOT Crane section power line with installation of main Switches/ Exhaust/ Painting work on iron structures in different shops along with required accessories at Regional Repair Shop (NK) Dakra, under GM Unit, NK Area
Repairing and Rewinding of Self startor and Alternator of Grove crane No-406781 ACE craneNo- JH10AL-2374 TipperNo-BPW-7371 Diesel bouser No-JH10AG-9798 Tipper No- BR17G-0791 at ANTST JG OCP Lodna Area BCCL.
Repairing of Engine, Fuel pump, gear box, brake, steering system, operator cabin, glass and seat, both side lift cylinder with its mounting, pulley and boom structure of Shakti-12 Crane No. MC 849 of Religara Project.
Repairing of hydraulic jack rear and front both side, fitment of boom extension and pully repairing, locking arrangement and repairing of engine assy of TIL Crane 40 T Sl no 408054 of Purnadih Project, NK Area.
Repairing, Servicing of traversing mechanism, including Gear box, lifting system and brake assy. of overhead Crane 05 Tone (Turbo make) of Machine shop - 01 no and Engine shop - 01 no of R.R. Shop Dakra, NK Area
Providing and fixing of starter in operating machine at different section, overload relay, power contactors with required accessories in EOT Crane of machine shop and STR Shop. Repairing, maintenance and fabrication of metallic structure and installa
Repairing of 02 Nos. steering cylinder, orbital valve seal changing, splined shaft teeth making, machining, steering rod internal spline teeth machining, steering rod adjusting of RT 630 crane Sl. No. 404324 at Nichitpur OCP, Sijua Area
For repairing of Tie rod and stud fitting of RT40 ESCORT CRANE Sl. No. 03911 and repairing of operator cabin gate and foot rest of Service van Sl. No. JH105G-6605 at AKWMOCP , KATRAS AREA, BCCL
Repairing of Shakti Crane JH10CW 2049 work like complete gear assly, clutch system assly, overhauling, repairing, Engine timing housing dismantling and seal with gasket, pinion requires replacement fitting as well as requires pump coupling, UJ cross
Repairing and replacement of trumped housing side cover side cover both sides and replacement of trumped housing (both sides) with inner oil seals and gasket of ACE 12XW Crane, Sl. No.MC-600 working at Jarangdih Colliery.
Supply & Fitment of Outriggers Seal Kits for 40 Ton Road Crane (Escorts, RT-40 STD) - (1) HOC Seal Kit, Pt.No.SDF.2370.000 of Escorts, Qty-4 No. (2) VOC Seal Kit, Pt.No.SDF.2382.000 of Escorts, Qty-4
Please Refer ANNEXURE B in Tender Document
Painter Line hose, Part No. 31637, Seal Kit DCV Emergency Valve Block, Part No. 30257-SEALS, Seal Kit For Painter Line Cylinder, Part No. HVE20101, Emergency Wire Rope, Part No. 41620, Suction Filter, Part No. 35002, Return Line Filter, Part No. 35005, Breather Filter, Part No. 35162, Suction Filter, Part No. 35062, Seal Kit For Anti-Pendulum Pitch Cylinder, Part No. BI1-3H-100487 Seal, Seal Kit For Pivoting Cylinder, Part No. 30330, Pressure Gauge, Part No. 21186, Seal Kit For Luffing Cylinder, Part No. HL0000823086, Seal Kit for Telescopic Cylinder, Part No. HL0000823508, Knuckle Cylinder Seal Kit, Part No. HL0000823086, Main DCV Seal Kit, Part No. 9005-01
PARK BRAKE ASSLY Part No.W7926000413, A2B SWITCH Part No.Z9352000015, CABLE A-2-B Part No.Z9352000033, SHEAVE - NYLATRON - 3 by 4 ROPE Part No.W7718000021, HYDRAULIC PRESSURE SENSOR Part No.Z9352000141, COIL Part No.Z9926000832, CART. and COIL ASSY. 24V Part No.9904110660, SEAL KIT FOR JACK Part No.Z9372000746, CHECK VALVE Part No.Z9372000743, HOSE ARMOURED Part No.X7543000081, FLUID LEVEL and T. GAUGE Part No.X7486000024, AMOURED HOSE Part No.X7543000080, OUTRIGGER D.C. VALVE Part No.W7926000419
Title1, Title2, Title3, Title4, Title5, Title6, Title7, Title8, Title9, Title10, Title11, Title12, Title13, Title14, Title15, Title16, Title17
Partial reinforcement of blade assy. Of BD155 Dozer Sl. No. 13717
FUEL INJECTION PUMP (FIP), PART NO. – 51Z7105433 (FOR BEML MAKE DOZER)
Pasting of Radium Tape and Writing of Machine Model and Machine Serial Number in 08 (Eight) nos. of BEML Dumpers, 09 (Nine) nos. of CAT Dumpers, 02 (Two) nos. of TIL Cranes and 01 (One) no. of Tyre Handler at Muraidih Workshop of AMP colliery.