REPAIR TO MISC WOODEN / STEEL FURNITURE ITEMS AND POLISHING / PAINTING OF FURNITURE FOR MISA CAMP UNDER GE(NORTH) TEZPUR

Amount

Note 1: (Applicable for all parts/items) : The biidders/contractors are advised to read tender document, all drawings & all corrigendum/amendments and general condition of contracts before entry/quoting the rates. Note 2:- Attention to bidder is hereby invited to upload revised BOQ if published during their bid submission. Uploading of incorrect/ pre-revised BOQ shall be treated as non bonafide and rejected. Fixed credit has been given in technical documents which shall be taken into account during acceptance of bid/tender.

Chair Dining :- M & L for removing of the following UNSV parts from chair dining and S&F new parts made out of well seasoned Ist class hard wood teak made to shape and size all as specified and shown on drg and as directed by Engr-in-charge. Drg No. FD-16,203,228,279

S&F Front leg

S&F Rear leg

S&F Front rail

S&F Rear rail

S&F Side rail

S&F Stiffener 'H' type

S&F Back Rest

Chair Easy :-M & L for removing of the following UNSV parts from chair Easy and S&F new parts made out of well seasoned Ist class hard wood teak made to shape and size all as specified and shown on drg and as directed by Engr-in-charge. Drg No. FD-17,201,229

S&F Front leg

S&F Rear leg

S&F Arm Rest

S&F Front rail of seat frame

S&F Rear rail of seat Frame

S&F Side rail of seat frame

S&F Side rail of back frame

Lower back frame

Upper Rail of back frame

Chair writing : M & L for removing of the following UNSV parts from chair writing and S&F new parts made out of well seasoned Ist class hard wood teak made to shape and size all as specified and shown on drg and as directed by Engr-in-charge.. Drg No. FD-20,202,250,280

S&F Front leg

S&F Rear leg

S&F Front rail

S&F Rear rail

S&F Side rail

S&F Stiffener 'H' type

S&F Back Rest

S&F Arm Rest

Caning of Chair all type . M& L for removing UNSV cane plastic from chair easy, chair dinning, chair writing etc and cleaning the surfaces and recaning the chair with 2mm wide 0.4 thick new plastic cane in godrej pattern and perimeter woven with 3 mm wide half round cane of approved make. Rest all as and shown on drg and as directed by Engr-in-charge. Drg No- FD-279, 229, 202,250 & 280

Bed Plywood Top : M & L for removing UNSV parts from Bed Ply top and S&F new parts made out of well seasoned Ist class hard wood teak made to shape and size all as specified and shown on drg and as directed by Engr-in-charge... Drg No. FD-246

S&F of Ply wood 12 mm thick commercial BWR grade Make Archid/ Century/green ply of approved make with appropriate screw.

S&F of ply wood 4 mm thick one side teak face on both side of head board with plywood Make Archid/ Century/green ply of approved make beaded with 4 mm thick teak wood beading.

All as per item No 6.02 above but foot board.

S&F of leg of head board made out of Ist class hard wood.

All as per item No 6.04 above but for leg of foot board

All as per item No 6.04 above but for long rail

All as per item No 6.04 above but for short rail

All as per item No 6.04 above but for stiffner

S&F of clamp iron 4 Nos each made out of 25 x 5 x 80 mm made to shape and fixed with appropriate screws.

Sofa Set 5 Seater :-M & L for removing of the following UNSV parts from Sofa set 5 Seater/4 seater/single seater and S&F new parts made out of well seasoned Ist class hard wood teak made to shape and size all as specified and shown on drg and as directed by Engr-in-charge. Drg No. FD-281

S&F Front leg Single seater

S&F Rear leg Single seater

S&F Arms rest

S&F Batten

S&F Front Long Rail of 3 Seater Seat frame

S&F Rear Long Rail of 3 Seater Seat frame

S&F Upper Long Rail of 3 seater back frame

S&F Lower long Rail of 3 seater back frame

S&F Side Rail of seat frame 3 seater/single seater

S&F Side Rail of Back frame 3 seater and single seater

S&F Front Rail of single seater Seat frame

S&F Rear Rail of single seater seat frame

S&F Upper Rail of Single seater back frame

S&F Lower Rail of single seater back frame

S&F PVC buffer

S&F of cushion foam 22”x21”x4” (PU Foam) 32 density of approved make and upholstery with cloth tapestry of approved quality duly provided zip. Rest all as specified and directed by Engr-in-charge.(Cost of tapestry cloth not less than Rs 385/- per meters).

Table Centre Drg No. M & L for removing of the following UNSV parts from Table centre and S&F new parts made out of well seasoned Ist class hard wood teak made to shape and size as per drg all as specified and shown on drg and as directed by Engr-in-charge. FD-29,235,274,375

Short rail.

Long rail.

Stiffener.

M & L for removing of UNSV top from table centre made out of 18mm thick prelaminated particle board exterior grade of approved make and beaded with 4 mm thick teak wood beading duly polished all round the top complete all as shown on drg and as directed by Engr-in-charge.

Table Peg : M & L for removing of the following UNSV parts from peg table and S&F new parts made out of well seasoned Ist class hard wood teak made to shape and size as per drg all as specified and shown on drg and as directed by Engr-in-charge. FD-46,236,277

Side rail.

Stiffener.

Top of peg table made out of 18mm thick prelaminated particle board exterior grade approved make and beaded with 4 mm thick teak wood beading duly polished all round the top.

Teapoy- M & L for removing of the following UNSV parts from teapoy wooden and S&F new parts made out of well seasoned Ist class hard wood teak made to shape and size as per drg all as specified and shown on drg and as directed by Engr-in-charge.. Drg No. FD-34(M),278

Long rail.

Short rail.

Stiffner 'H' Type

M & L for removing of U/S top from teapoy and S&F top made of 18mm thick prelaminated particle board exterior grade approved make and beaded with 4 mm thick teak wood beading duly polished all round the top.

Table Dining 6 Pers: M & L for removing the following UNSV parts from table dining 6 pers and S&F new parts made out of well seasoned Ist class hard wood teak made to shape and size as per drg all as specified and shown on drg and as directed by Engr-in-charge. Drg No. FD-46,236,277,273

Long rail.

Short rail.

M & L for removing UNSV corner brackets and S & F new corner brackets made out of 100x100x25mm 4 Nos each made to shape and fixed with appropriate screws.

M & L for removing of UNSV top from Table ding 6 pers and S&F top made out of 18mm thick prelaminated particle board exterior grade approved make and beaded with 4 mm thick teak wood beading duly polished all round the top.

Chair Dining M/L for removing theUNSV parts from chair Dining MAP and S&F new parts made out of well seasoned Ist class hard wood Teak made to shape and size as per drg duly polished complete all as specified and shown on drg and as directed by Engr-in-charge.. Drg No. MAP FD/E6/MAP/04

Front leg

Rear leg

Front rail of Seats

Rear rail of Seats

Side rail of Seats

Stiffener 'H' type

Back Rest stiffener

S&F Corner between leg and rail 75mmx75mmx25mm

M/L for removing UNSV seat and S & F new seat made of 12mm thick plywood BWR grade Make.Archid/ Century/green ply of approved make and to fix 75 mm thick 32 density foam cushion and upholstery with leathrite tapestry cloth of approved quality and tightening the frame with bamboo pins,wooden screw before fixing of seat. Rest all as per drg and directed by Engr-in-charge.(Cost of raxine not less then Rs 250/- per mtrs.)

Table Dressing Ladies. M/L for removing of the following UNSV parts from Table Dressing Ladies with Mirror and S&F new parts made out of Ist class hard wood Teak well seasoned made to shape and size as per drg duly polished complet all as specified and shown on drg and as directed by Engineer-in-charge. Drg No FD-32,251 & 378

S&F new top made of 18mm thick prelaminated particle board exterior grade, both side laminated. Rest all as specified in the drg and as directed by Engineer-in-charge.

S&F 5 mm thick mirror of Make : Atul/Modigaurd/Saint Gobain as approved and fixed with Teak wood frame & 6mm thick plywood commercial type all as specified and directed by Engr-in-charge.

S&F new drawer with front of 18mm thick prelaminated particle board, exterior grade, both side laminated , back and sides of 12mm thick teak wood planks and bottom with 6mm thick plywood commercial grade. Rest all as specified in the drg and as directed by Engineer-in-charge.

M/L for removing of U/S knob and S&F new knob of best quality as per drg and directed by Engr-in-charge .

M/L for removing UNSV leg and S&F leg made out of Ist class teak wood as per drg and specification.

M&L for removing UNSV Glass sliding shutter with aluminium channel and S&F new Glass shutter made out of 5mm thick glass plain with aluminium channel 20 mm with two way arrangenment. Rest all as specified in the drg and as directed by Engineer-in-charge.

Almirah large steel with shelves /1/2S 1/2H : M & L for removing UNSV shelves from almirah large steel and S&F of new shelves made of 1.0 mm thick MS sheet all as specified and shown on drg and as directed by Engr-in-charge. Drg No FD-351,104(m),1031,1033

All as per item No 14.00 above but lock cover.

All as per item No 14.00 above but leg.

M& L for spot welding to almirah large steel complete all as specified and shown on drg and as directed by Engr-in-charge.

M & L for removing UNSV 3 way locking device from almirah large steel and S&F new 3 way locking device all as specified and shown on drg and as directed by Engr-in-charge.

M & L for removing UNSV lock from almirah large steel and S& F new lock 6 lever Make: Godrej/Link of approved make rest all as specified and shown on drg and as directed by Engr-in-charge.

M & L for removing UNSV handle from steel almirah and S&F of new handle of chromium plated all as specified and shown on drg and as directed by Engr-in-charge.

M & L for removing UNSV door hinges from steel almirah and S&F of new door hinges 75/80 mm duly welded all as specified and shown on drg and as directed by Engr-in-charge.

Almirah Med steel with shelves : M & L for removing unserviceable shelves from almirah med steel and S&F of new shelves made of 1.0 mm thick MS sheet all as specified and shown on drg and as directed by Engr-in-charge. Drg No. FD-243,114(M),1032,1034

All as per item No 15.00 above but lock cover.

All as per item No 15.00 above but leg.

M& L for spot welding to almirah Med steel complete all as specified and shown on drg and as directed by Engr-in-charge.

M & L for removing UNSV 3 way locking device from almirah med steel and S&F new 3 way locking device all as specified and shown on drg and as directed by Engr-in-charge.

M & L for removing UNSV lock from almirah large med and S& F new lock 6 lever Make: Godrej/Link of approved make rest all as specified and shown on drg and as directed by Engr-in-charge.

M & L for removing UNSV handle from almirah med steel and S&F of new handle of chromium plated mild steel all as specified and shown on drg and as directed by Engr-in-charge.

M & L for removing UNSV door hinges from almirah med steel and S&F of new door hinges 75 mm duly welded all as specified and shown on drg and as directed by Engr-in-charge.

Chair Varandah: M& L for spot welding to chair varandah complete all as directed.. Drg No FD-333,19,256

M & L for removing UNSV cane plastic from chair varandah and smooth the surface and apply two coats of white synthetic enamel paint complete all as specified and shown on drg and as directed by Engr-in-charge.

M&L for Re-canning of Chair Varandah in mat pattern with 4 mm wide 0.5 mm thick half round plastic cane of approved make all as specified and shown on drg and as directed by Engr-in-charge.

M & L for removing UNSV hard PVC shoes from chair verandah and S&F new PVC shoes four Nos each chair complete all as specified and shown on drg and as directed by Engr-in-charge.

Table Office Officer steel : M & L for removing UNSV top from table office officers steel and S&F of new top made out of Pre laminated particle board 18/19mm thick exterior grade of approved make with 4mm thick teak wood beading around the top complete all as specified and shown on drg and as directed by Engr-in-charge. Drg No. FD-1033

M & L for removing UNSV drawer from table office officers steel and S&F new drawer made of 1mm thick PBI sheet and all as specified and shown on drg and as directed by Engr-in-charge.

M&L for removing UNSV leg and S & F New leg made of MS square pipe 25mm and 1.6mm thick 04 Nos in each table rest all as specified and shown on drg and as directed by Engr-in-charge.

M& L for spot welding to Table office offrs steel all as specified and shown on drg and as directed by Engr-in-charge.

M & L for removing UNSV stiffener and S & F new stiffener made out of MS square pipe 25mm and 1.6mm thick of Qty 03 Nos in each table rest all as per drg and as directed by Engr-in-charge.

Removing UNSV hard PVC shoes from Table office offrs and S&F new PVC shoes four Nos each table and all as specified and shown on drg and as directed by Engr-in-charge.

Table office Clk steel: M & L for removing UNSV top from table office clk steel and S&F of new top made out of Pre laminated particle board 18/19mm thick exterior grade of approved make and beaded with 4mm thick teak wood beading complete all as specified and shown on drg and as directed by Engr-in-charge. Drg No. 84(M),1004

M & L for removing UNSV drawer from table office clk steel and S&F new drawer made of 1mm thick PBI sheet and all as specified and shown on drg and as directed by Engr-in-charge.

M & L for removing UNSV leg and S & F New leg made of MS square pipe 25mm and 1.6mm thick rest all as specified and as directed.

M & L for removing UNSV hard PVC shoes from table office clk and S&F new PVC shoes four Nos in each table and all as specified and shown on drg and as directed by Engr-in-charge.

M & L for removing UNSV stiffener and S & F new stiffener made out of MS square pipe 25mm and 1.6mm thick of Qty 03 in each table all shown on drg and as directed by Engr-in-charge.

M& L for spot welding to Table office clk complete all as directed

Table Steel 3'X2' with & w/o drawer M & L for removing UNSV top from Table Steel 900X600X760mm with and without drawer and S&F of new top made out of Pre laminated particle board 18/19mm thick exterior grade of approved make and beaded with 4mm thick teak wood beading complete all as specified and shown on drg and as directed by Engr-in-charge. Drg No FD-1007,1008

M & L for removing UNSV drawer from table 900x600'x760mm steel with drawer and S&F new drawer made of 1mm thick PBI sheet all as specified and shown on drg and as directed by Engr-in-charge.

M&L for removing UNSV leg and S & F New leg made of MS square pipe 25mm and 1.6mm thick rest all as specified and shown on drg and as directed by Engr-in-charge.

M& L for spot welding to Table Steel 900x600x760mm complete all as specified and shown on drg and as directed by Engr-in-charge.

M & L for removing UNSV hard PVC shoes from Table Steel 900x600x760mm and S&F new PVC shoes four Nos in each table all as specified and shown on drg and as directed by Engr-in-charge.

Removing UNSV stiffener and S & F new stiffener made out of MS square pipe 25mm and 1.6mm thick of Qty 03 in each table rest all as specified and shown on drg and as directed by Engr-in-charge.

Chair CBA Steel with Arms: M & L for removing UNSV seat from chair steel tubular and S&F new seats made out of 2nd class seasoned teak wood duly Canned with half round plastic cane 2mm wide 0.4mm thick and perimeter woven with 3mm wide 0.5mm thick cane and painting with black synthetic enamel paint rest all as specified and shown on drg and as directed by Engr-in-charge. Drg No FD-75

All as per item No. 20.00 above but back.

M & L for removing UNSV MS cleats from chair CBA steel and S & F new MS cleats of size 50 X 25 X3mm, 4 Nos each chair on seat and back by welding to rest the seat complete all as specified and shown on drg and as directed by Engr-in-charge.

M & L for removing of old UNSV arms rest from chair CBA steel and S&F new arms rest made out of 2nd class seasoned hard wood fitted with appropriate screws all as specified and shown on drg and as directed by Engr-in-charge.

M/L for removing of U/S PVC shoes and S&F new hard rubber shoes with appropriate screws as per drg and directed by Engr-in-charge .

Chair CB Steel w/o Arms: M & L for removing UNSV seat from chair steel tubular and S&F new seats made out of 2nd class seasoned teak wood duly Canned with half round plastic cane 2mm wide 0.4mm thick and perimeter woven with 3mm wide 0.5mm thick cane and painting with black synhetic enamel paint rest all as specified and shown on drg and as directed by Engr-in-charge. Drg No FD-75

All as per item No. 21.00 above but back.

M & L for removing UNSV MS cleats from chair CB steel and S & F new MS cleats of size 50 X 25 X3mm, 4 Nos each chair on seat and back by welding to rest the seat complete all as specified and shown on drg and as directed by Engr-in-charge.

M/L for removing of U/S PVC shoes and S&F new hard rubber shoes with appropriate screws as per drg and directed by Engr-in-charge .

Teapoy verandah: M/L for removing UNSV top from teapoy verandah and fix the frame properly and painting the frame with white synthetic enamel paint of approved quality and S&F top with white balance made out of prelaminated particle board 19mm thick exterior grade of approved make beaded with 4 mm thick teak wood beading and duly painted with white paint and S&F PVC/hard rubber shoes on the leg.Rest all as specified and shown on drg and as directed by Engr-in-charge.

Locker Bed Side Steel. M & L for removing UNSV handle from locker bed side steel and S&F stainless steel chromium plated handle 100mm of approved quality 2 Nos each all as specified and shown on drg and as directed by Engr-in-charge. Drg No FD-1029,257

M & L for removing UNSV hasp and staple from locker bed side steel and S&F new Aluminium hasp and staple 100mm with appropriate screws all as specified and shown on drg and as directed by Engr-in-charge.

M & L for removing UNSV shelf from locker bed side steel and S&F new shelf made out of MS sheet 1.0mm thick all as specified and shown on drg and as directed by Engr-in-charge.

M & L for removing UNSV hanging rod from locker bed side steel and S & F CP Hanging rod 19mm dia 1.6 mm thick as approved and all as specified and shown on drg and as directed by Engr-in-charge.

M & L for removing UNSV legs from locker bed side steel and S&F of new leg made of 1.6mm thick MS sheet made to shape duly painted with two coats of OG synthetic enamel paint over a coat of red oxide primer complete all as specified and shown on drg and as directed by Engr-in-charge.

Bed hard Map: Removing the unsv plywood top from bed hard and S & F new Ply wood top of 12mm thick BWR grade commercial type Make.Archid/ Century/green ply of approved make complete all as per existing shape and size as per drg and directed by Engr-in-Charge. Drg No FD/E6/MAP/08(R)

Removing of Old broken/unsv Stiffners and S & F New Stiffners of 25mmx25mm MS square pipe of 1.6mm wall thickness as per existing shape and size welded between long rails/legs duly painted with two coats of black enelamed paint over a coat of red oxide primer, complete all as per drg and as directed.

Removing of Old broken/unsv PVC Shoes and S & F New PVC shoes as per existing shape and size as per drg and as directed by engineer in-charge.

Charpoy MS Tubing with ply top:Removing the old unsv plywood top from Charpoy MS Tubuing and S & F new Ply wood top of 12mm thick BWR grade commercial type Make Archid/ Century/green ply of approved make complete all as per drg and specification and as directed by Engr-in-Charge. Drg No FD/MAP-II/01 and CWE/TEZ/FD-04

Removing of Old broken/unsv Stiffners and S & F New Stiffners of 25mmx25mm MS square pipe of 1.6mm wall thickness as per existing shape and size welded between long rails/legs duly painted with two coats of black enelamed paint over a coat of red oxide primer, complete all as per drg and as directed.

Removing of Old broken/unsv PVC Shoes and S & F New PVC shoes as per existing shape and size as per drg and as directed by engineer in-charge.

Table Computer: M/L for removing UNSV parts from table computer and S&F new parts for the following items as per drg and specification and as directed by Engr-in-charge. Drg No FD/E6/MAP/03

M/L for removing UNSV top and S&F top made out of prelaminated particle board 19mm exterior grade of approved make beaded with PVC edging as per drg and specification and as directed by Engr-in-charge.

S&F drawer with telescopic channel.

S&F sliding board with telescopic channel.

S&F sides.

S&F PVC shoes.

Chair computer (TP):- M/L for removing UNSV seat and S&F new seat as per trade pattern.

M/L for removing UNSV back and S&F new back as per trade pattern.

M/L for removing UNSV arms and S&F new arms as per trade pattern.

M/L for removing UNSV hydrulic system and S&F new hydraulic system as per trade pattern.

M/L for removing UNSV caster wheeel and S&F new caster wheeel as per trade pattern.

Chair revolving excecutive (TP):- M/L for removing UNSV seat and S&F new seat as per trade pattern.

M/L for removing UNSV back and S&F new back as per trade pattern.

M/L for removing UNSV arms and S&F new arms as per trade pattern.

M/L for removing UNSV hydrulic system and S&F new hydraulic system as per trade pattern.

M/L for removing UNSV caster wheel and S&F new caster wheel as per trade pattern.

Charpoy GI Pipe with ply top :- M/L for Removing of UNSV elbow from charpoy GI pipe and S&F new GI elbow 32mm dia med gradeof approved make complete all as specified and shown on drg and as directed by Engr-in-charge. Make: Jolly / RI / RM /KI as approved. Drg No FD-220

M/L for Removing of old unserviceable check nut from charpoy GI pipe and S&F new GI check nut 32 mm dia 10mm thick and tight the charpoy with the entire satisfaction complete all as specified and shown on drg and as directed by Engr-in-charge.

M/L forremoving U/S long rail from charpoy GI Pipe 32mm dia and S&F long rail 32mm dia medium grade heavy of approved make duty threaded on both ends all as specified and shown on drg and as directed by Engr-in-Charge. Make Jindal/Tata/Prakash/Surya as approved.

M/L for cutting of dismantled old long rail from charpoy GI Pipe 32mm dia and modifying in to short rail and threaded both ends fixing the same to charpoy GI pipe all as pecified and as directed by the Engr-in-Charge.

M/L for cutting of dismantled old short rail from charpoy GI Pipe 32mm dia and modifying into legs and threaded of end and M&L for welding the clamps for FMN set and welded 6mm thick cap at bottom and fixing the same to charpoy GI pipe all as specified and as directed by the Engr-in-Charge.

M & L removing UNSV MS flat iron of size 25x5x850mm long and S&F new MS flate iron as per existing size 25x5x850mm long in between long rail and two holes each for fixing plywood and apply one coat of paint synthetic enamel black to the iron surfaces over a coat of primer complete all as specified and directed by Engr-in-charge.

M/L for removing UNSV plywood top and S & F plywood 12 mm thick commercial BWR Make.Archid/ Century/green ply of approved make with appropiate nut and bolt 6mm headless with washer complete all as specified and shown on drg and as directed by Engr-in-charge.

Charpoy GI pipe nylon newar to plywood top:- M & L for removing of UNSV nylon newar from charpoy GI pipe 32mm and S&F three Nos MS flats Iron size 25x5x850mm long to be fixed by welding in between long rail in equal distance and two holes in each flate iron and apply black synthetic enamel paint over a coat of primer rest all as directed by Engr-in-charge. Drg No FD-220

S&F MS flat iron size 25x5x220mm long four number each to be fixed by welding in each corner in between long rail and short rail and one hole on each flate iron and apply black synthetic enamel paint over a coat of primer rest all as directed by Engr-in-charge..

S&F ply wood 12mm commercial BWR grade Make.Archid/ Century/green ply of approved make with appropriate nut and bolt headless 6mm with washer complete all as specified and shown on drg and as directed by Engr-in-charge.

M&L for removing of UNSV long rail from charpoy GI Pipe 32mm and S&F long rail made of GI tubing 32mm dia medium grade heavy duty of approved make duly threaded on both ends all as specified and shown on drg and as directed by Engr-in-charge.

M&L for cutting of dismantled old UNSV long rail from charpoy GI Pipe 32mm dia modifying into short rail by threading both ends and fixing the same to charpoy GI pipe all as specified and shown on drg and as directed by Engr-in-charge.

M/L for cutting of dismantled old short rail from charpoy GI Pipe 32mm dia and modifying into legs and threaded of end and M&L for welding the clamps for FMN set and welded 6mm thick cap at bottom and fixing the same to charpoy GI pipe all as specified and as directed by the Engr-in-Charge.

M & L for removing of UNSV elbow from charpoy GI pipe and S&F elbow GI three way 32mm dia med grade of approved make. Rest all as specified and shown on drg and as directed by Engr-in-charge.

M & L for removing of old UNSV check nut from charpoy GI pipe and S&F new GI check nut 10mm thick complete all as specified and shown on drg and as directed by Engr-in-charge.

Painting:- M&L for removing the rusty surfaces, denting and applying putty to smooth the surfaces and painting with two coats of synthetic enamel OG paint of approved make all as specified and as directed by Engr-in-charge for followings:-

Almirah large steel /1/2S 1/2H. Drg No FD,1031,1033

Almirah med steel. Drg No FD- 1032, 1034

Charpoy MS Tubular with ply top. Drg No CWE/Tez/FD-04, FD/E6/MAP/08(R)

Locker bed side steel. Drg No FD-1029

Table 3'x2' with or without drawer steel. Drg No FD-1007, 1008

Table office clk steel. Drg No FD-1004

Table offie offrs steel. Drg No FD-1003

Chair CBA steel . Drg No FD-75

Chair CBB steel. Drg No FD-75

Table computer. Drg No FD/E6/MAP/03

Polishing : M&L for removing old polish from the surfaces by scrubbing with emery paper, cleaning all dust, filling bore holes with pasty filter prepared by mixing plaster of paris with water to a creamy consistence and adding raw in quantity to obtain the desired colour to the base and to allow the surface to be dried up and set aside for 24 hrs for the surfaces to harden, rub the surface with sand paper it is thoroughly smooth and dried to receive a coat of acrylic wood finish polish of approved make complete all as specified directed by Engr-in-charge for the followings:-

Chair dining. Drg No FD- 279,MAP FD/E6/MAP/04

Chair Easy . Drg No FD- 229

Chair writing. Drg No FD-250, 280

Bed Ply wood top. Drg No FD-245, 246, 247

Table center. Drg No FD-235, 274

Table peg. Drg No FD-46,236 & 277

Table writing . Drg No FD- 275 , DB-3902

Teapoy (W). Drg No FD-232 & 284

Sofa Set 5 Seater . Drg No FD-281, 373

Table dining 6 Pers. Drg No FD-236, 277

Table dressing Ladies . Drg No FD-32,251 & 378

Chair dining Map. Drg No FD/E6/MAP/04

Sofa three seaters for offrs :- Removing of u/s tapestry cloth, foam cushion and newar strings of seat from three seater sofa and S&F 12mm thick BWR plywood of size 1650mm x 520mm for seat and providing new foam cushion 100mm thick over seat and back and upholestering all over three seater sofa with best quality tapestry cloth as shown in drg and as directed by Engr-in-Charge. Drg No , FD-TP

Sofa chair single seater for offrs:- Removing of u/s tapestry cloth, foam cushion and newar strings of seat from single seater sofa and S&F 12mm thick BWR plywood of size 540mm x 520mm for seat and providing new foam cushion 100mm thick over seat and back and upholestering all over single seater sofa with best quality tapestry cloth as shown in drg and as directed by Engr-in-Charge.Drg No , FD-TP

Sofa three seaters for JCOs:- Removing of u/s tapestry cloth, foam cushion and newar strings of seat from three seater sofa and S&F 12mm thick BWR plywood of size 1650mm x 580mm for seat and providing new foam cushion 100mm thick over seat and back and upholestering all over three seater sofa with best quality tapestry cloth as shown in drg and as directed by Engr-in-Charge.Drg No , FD-TP

M/s Singh Furniture Mart