ADDN/ALTN TO OTM ACCN FOR FIGHTER SQN AND PROVISION OF WORK SERVICES FOR FITMENT OF CAR WASHER IN MT YARD OF 365 TRU AT AF STN NALIYA

Amount

Demolition of cement concrete of any description and in any position complete all as specified and directed.

Demolition of brickwork or stone/ boulder masonry / PCC block masonry, built in cement or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles including removal of debries to a distance exceeding 1.5 Km but not exceeding 2 Km complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

Dismantling of existing lime concrete/PCC padding of any thickness and description laid over RCC roof/Chajjas etc, cleaning and washing of roof with water to remove dust etc to receive waterproofing treatment including removal of debris out side MD land complete all as specified and directed.

Taking down cement plaster of any descreption and in any position of brick or concrete surfaces & racking out joints hacking for key, scrubbing down with water etc complete all as specified and directed.

Taking down chowkhats or frames exceeding 1.5 sqm but not exceeding 4 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed.

Excavatiing in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, pipe lines, laying of cable etc. not exceeding 10 sqm on plan and not exceeding 1.5 metre in depth and getting out in soft/loose soil and levelling of bottom surface to required level for pipe line complete all as specified and directed.

Excavating in trenches, exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 sqm on plan and not exceeding 1.5 metre in depth and getting out in soft/loose soil complete all as specified and directed.

Excavating over areas, not exceeding 1.50 metre deep and getting out in hard/dense soil complete all as specified and directed.

Returning filling in including spreading, leveling ,and well ramming, in layers not exceeding 25 cm each layer of any kind of soil complete all as specified and directed.

Removing excavated material (soil) from site not exceeding 50 metre from starting point and depositing where directed at level not exceeding 1.5 metre above the starting point.

Material and labour for pre-cast cement concrete block masonry 1:3:6 (20mm graded aggregate) with solid blocks, exc. 10 cm in width and setting in cement mortar 1:4, complete all as specified and directed.

Material and labour for hard core of broken boulder of guage not exceeding 63mm, deposited spread and levelled in layers not exceeding 15cm thick watered and rolled rammed to a true surface complete all as specified and directed.

Material and labour for moorum filling in pavings of road, laid in layers not exceeding 15 cm thick spread, leveled and rammed including watering complete all as specified and directed

Material and labour for PCC 1:2:4, type B2 (using 40 mm graded stone aggregate) as in foundations complete all as specified and directed.

Material and labour for PCC 1:2:4, type B1 (using 20 mm graded stone aggregate) as in copings / benching of man holes incl weathering rounded / chamfered angles and throating as directed including necessary form work . Exposed surfaces of concrete shall be finished even & smooth using extra cement complete all as specified and directed.

Material and labour for PCC 1:3:6, type C2 (using 40mm graded aggregate) as in concrete bed for drain pipe 150 mm bore of SWG including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and as directed.

Material and labour for 25 mm thick PCC 1:2:4, type B0 (using 12.5mm graded stone aggregate ) as in floor finished even and fair with out using extra cement complete all as specified and directed.

Material and labour for 75 mm thick PCC 1:4:8, type D2 (using 40mm graded stone aggregate) over hardcore complete all as specified and directed.

Material and labour for 100 mm thick PCC 1:4:8, type D2 (using 40mm graded aggregate) in sub-floors, sub-bases, floors and pavings etc complete all as specified and directed.

Material and labour for RCC M-30 design mix (using 20 mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams, lintel beam; bases for columns, etc; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

Material and labour for RCC M-30 design mix (using 20 mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Material and labour for RCC M-30 design mix (using 20 mm graded stone aggregate) as in Chajjas complete all as specified and directed.

Material and labour for RCC 1:2:4 type B1 (using 20 mm graded stone aggregate) as precast man hole cover slabs including necessary form work set in CM 1:4. Exposed surface of concrete shall be finished even & smooth with out using extra cement Note :- Reinforcement shall be measured & paid seperately.

Material and labour for CRS bars 6 to 8 mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Material and labour for CRS bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less then 0.9 mm dia or securing with clips complete all as specified and directed.

Use and waste formwork to sides of concrete foundations, footings, bases of columns, raft & raft beams, sides & soffits of foundation & plinth beams; and similar work; verticle or to batter flat fair finished surfaces of concrete complete all as specified and directed.

Use and waste formwork to sides of pillars, posts, struts, piers,columns, and stanchions circular on plan rough finished surfaces of concrete complete all as specified and directed.

Use and waste formwork to chullah hoods, chajjas, troughs & similar items including edges flat fair finished surfaces of concrete complete all as specified and directed.

Material and labour for vitrified ceramic tiles light shade 10 mm thick colour (square/rectangular) polished, area of each tiles exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles, including 15 mm thick screed bed in CM 1:6 complete all as specified and as directed.

All as per serial item number 31.00 here-in-before but 10mm thick rendering in in CM(1:3) as skirting complete all as per specified and directed.

Material and labour for glazed ceramic coloured tiles, 350X250X7mm/ 450X350X7mm thick in size, set on vertical surfaces such as skirting, dado, etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles including 10mm thick rendering in CM 1:3, complete all as specified and as directed.

Material and labour for coloured non skid ceramic tiles of size 300x300mmx7mm thick in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

Material and labou for machine pressed precast concrete interlocking paver block of approved shape and size of 60mm thickness, with minimum compressive strength of 35N/sqm (M-35 ), without correction factor for chamfering, made in rubber moulds with 0.50mm thick scratch proof lacquer coating on top surface, with white cement and pigment laid over and complete all as specified and directed.

Material and labour for sand cushioning 25 mm thick over concrete surfaces, spread complete all as specified and directed .

Filleting in any position and to any shape in CM 1:4 including all mitres, stops, etc. exceeding 25 sq.cm but not exceeding 50 sq.cm. complete all as specified and as directed.

Material and labour for 15 mm thick rendering in CM 1:4 on other than fair faces of brick work or concrete surfaces finished fair and smooth without using extra cement complete all as specified and as directed.

Material and labour for 10 mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4, finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for 5mm thick rendering on celing surfaces in CM 1:3 finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for preparation of new plastered surface and applying two coats of oil bound distemper over a coat of alkali resistant primer and sand papering till obtaining smooth surface to the entire satisfaction of Engineer in charge complete all as specifed and as directed

Material and labour for preparation of new surfaces of ceiling and applying three coats of white wash complete all as specified and directed

Material and labour for applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004, Alkali & Fungal resistance, dirt resistance exterior paint of required shade (Company Depot tinted) with silicon additives @ 1.43 Litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm over new surfaces complete all as specified and as directed.

Complete removal of existing treatement and applying two coats of oil bound distemper over a coat of alkali resistant primer and sand papering till obtaining smooth surface to the entire satisfaction of Engineer in charge complete all as specifed and as directed. Note : The debris obtained from removal of existing surface shall be disposed off to outside MD land and shall be deposited at any approved locations as ascertained by the contractor. No any extra cost shall be entertained on this ground.

Material and labour for applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over existing surfaces of wall/ pavement with camouflage pattern on wall including removal of existing treatement wiht brooming down or steel wire brushing etc complete all as specified and directed.

Supply and fix aluminum snap grid powder coated frame work for false ceiling, size of grid 605 x 605mm along with 4mm dia mild steel wire class 3 as in suspenders complete all as specified and directed.

Supply and fix 10mm thick PVC insulation panels with EPS stuck to 1mm plain PVC sheet suitably placed in false ceiling grid made of Aluminium/G.I./M.S. as per specification and drawing complete all as specified and directed.

Supply and fix in repairs solid PVC wall lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification and drawing complete all as specified and directed.

Supply and fix in repairs 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC frame as per specifications and drawing complete all as specified and directed.

Supply and fix steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St.-240 complete all as specified and directed.

Supply and fix for roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats,gusset plates,wind ties etc of Fe410- W(GdeE-250) quality-B complete all as specified and directed.

Supply and fix for mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long Diameter of neck 11 to 15 mm complete all as specified and directed.

Supply and fix for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Material and labour for preparation of new steel or iron surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, primer complete all as specified.

Complete removal of existing water proofing treatment from top of roof and canopies/chajjas of buildings including taking out earthing strip, electric strip and cable at the same place after execution of APP membrane including removing the debris outside of MD land complete all as specified and ditrected.

Material and labour for screed bed or bedding layer of mortar 10 mm thick in cement mortar 1:4 including mixing only liquid water proofing compound as per manufacturers' instructions and finishing the surface fair and even complete all as specified and ditrected. Note:- WPC shall be measured & paid separately.

Supply only liquid water proofing compound

Material and labour for 25 mm thick (average) as level course PCC 1:2:4 type B0, (using 12.5 mm graded stone aggregate) as in roof pading, complete all as specified and directed

Material and labour for repairing the edge/corner of Chajja/roof projection down ward type and similar work by using cement concrete 1:2:4, type B0 including necessary formwork & 5 mm thick rendering in CM 1:4 to match with existing surface complete all as specified and directed.

Material and labour for cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 complete all as specified and as directed.

Material and labour for water proofing treatment by applying one coat of oil base bituminous primer @ 0.3 Kg / Sqm with brush / roller, laying of 3 mm thick APP based polymer modified membrane (mineral finish) reinforced non-woven polyester, weight not less than 3.50 Kg / Sqm and sealing all the over laps 150 mm in length side and 100 mm in width side of membranes laid with torch application complete all as specified and as directed.

Supply and fix solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube, as per specification and drawing complete all as specified and directed.

Supply and fix factory made solid panel PVC door shutters, 30 mm thick (style) consisting of frame made out of MS tube for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' chanel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either sides & as gap insert for top & bottom rails. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed stiles & rails with suitable PVC sheet beading and jointed together with solvent cement. Supply and fixing in the frame at site as per specification and drawing complete all as specified and directed.

Supply and fix 100 mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

Supply and fix aluminium anodised barrel tower bolts 150mm long of extruded section and fixed complete all as specified and directed.

Supply and fix 150mm size extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed.

Supply and fix aluminium powder coated (minimum thickness of powder coating 50 micron of approved colour) ventilator, partially glazed and partially louvers, outer, frame & mullion on fabricated with aluminium section of size 82.50mmx38.00mmx1.70mm thick (Cat No. 20036), half portion glazed with 4mm thick frosted glass including rubber beading, & glazing clip, half portion louvers of 80mm wide & 4mm thick frosted glass including aluminium louver patti including fixing of S.S wire gauge of 0.36mm dia and 1.40 width of aperature with 25x3mm thick aluminium strip with screw to upper half portion of ventilator all fitting & fixture and fixed in position complete all as specified and as directed. Note :- Section No given above are of make Jindal, Contractor may use similar section of other make as mentioned in Appx 'B' to Particular Specfications.

Supply and fix aluminium powder coated (minimum thickness of powder coating 50 micron) three track sliding window frame of section size 92.00x 31.75x1.3mm comprising of one number of fly proof shutter and two numbers of glazed shutter frames of section size 40x18x1.3mm thick with necessary joining cleats, glazing clips, rubber gasket, anodised aluminium snap beading and connected locking arrangement complete all as specified and directed. Notes:- (i) Glass filling in panels of windowa and aluminium wire mesh/wire cloth shall be demed to be included in the quoted rate for the itme. (ii) aluminium alloy wire cloth in panels wite gauzed shutter shall be 0.45mm nominal dia of witer and average width of aperture 1.40mm, fixed with aluminium wire staples. (iii) Glass filling in panels of glazed shutter shall be 4mm thick tinet sheet glass complete all as specified and directed.

Supply and fix in position aluminium powder coated (minimum thickness of powder coating 50 micron) door shutter with frame, partly glazed with 5mm thick tinted glass and partly panelled with 9mm thick prelaminated particle board with both side decorative laminated including rubber bead, joining cleat for fixing in position, aluminium door handle 150mm size, aluminium barrel tower bolt 200mm size etc of any size complete all as specified and directed with following sections:- (a) Frame (top & side) section shall of size 101.60 x 44.75 x 2.4mm (Section No 14021) (b) Vertical members of shutter section shall be of size 85.00 x 44.45x2.00mm (Section No 19560) (c) Top members of shutter section shall be of size 83.50 x 44.45x2.00 mm (Section No 19596) (d) Lock rail (middle member ) of shutter section shall be of size 150.00x44.45x3.00 mm (Section No 19596) (e) Bottom member of shutter section shall be of size 150.00 x44.45x3.10mm (Section 19584) (f) Glazing clip for securing glass of shutters shall be of 0.80mm thick (Section No 19370). Note : Section No given above are of make Jindal, contractor may use similar section of other make mentioned in Appendix 'B' to Particular Specfications.

Supply and fix aluminum anodised grill of 5 mm thick , rectangular, tupe of shape aperture not exc 100 sqcm fixed with H or F channel 38 mm x 12 mm x 1.30 mm design pattern DG 103 of Decogril or equivalent complete all as specified and as directed.

Supply and laying GI pipe 25 mm bore medium grade ISI marked including all fittings in old/new position as in walls and ceilling/trenches, complete all as specified and directed.

Supply and laying GI pipe 20 mm bore medium grade ISI marked including all fittings in old/new position as in walls and ceilling/trenches, complete all as specified and directed.

Material and labour for cutting GI pipe of size 40mm dia in position for insertion of new tees, branches of 40x25mm etc complete all as specified and directed.

Material and labour for cutting GI pipe of size 50 mm dia in position for insertion of new tees, branches of 50x25 mm etc complete all as specified and directed.

Cutting chases pinning in making good to facing where required for concealed water tubing and making good cutting not exceeding 10 cm girth in stone/concrete walls complete all as specified and directed.

Supply and fix unplasticised PVC pipes of pressure rating 10 kgf/cm sqr with all fittings and fixed to walls and ceilings or laid in floors for 15 mm bore complete all as specified and directed.

Supply and fix unplasticised PVC pipes of pressure rating 10 kgf/cm sqr with all fittings and fixed to walls and ceilings or laid in floors for 20 mm bore complete all as specified and directed.

Supply and fix stop cock 15 mm dia, cast copper alloy but fancy type chromium plated screwed down high presser with crutch or butter fly handle on both ends for iron pipe or for union fixed complete all as specified and directed.

Supply and fix bib taps 15mm dia bore, chromium plated cast copper alloy with crutch or butter fly handle , screwed down, or secrewed for iron pipe or for brass ferrule complete all as specified and directed.

Supply and fix 15mm bore pillar tap swan neck type , cast copper alloy, with capstan heads, fancy type chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

Supply and fix soap dish, chromium plated aproximate size 160x 160x90mm complete all as specified and directed .

Supply and fix vitreous china counter wash basin ovel type, white, 560 mm x 470 mmx190mm dia complete all as specified and as directed.

Supply and fix vitreous china squatting pan `Orissa’ pattern, size 580x440mm white with integral foot rest (excluding flushing cistern and flush pipe) with ‘P’ or ‘S’ trap including provision of lime concrete bedding complete all specified and directed.

Supply and fix vitreous china half stall urinals bowel type (back or corner wall type) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 secuing urinal to plugs with and including 60mm long brass screws pointing around urinal back in cement, fixing automatic flushing cistern with brackets flush pipe grating and union fo dischage pipe (excluding of fixing supply pipe to flushing cistern, trap) including waste pipe omplete all specified and directed.

Supply and fix 10 litre capacity PVC valve less symphonic action type flushing cistern, white ,with inlet ball valve, float and handle including bracket and 32 mm dia HDPE flush pipe and connected to squat pattern /pedestal pattern water closet (Flush shall be fixed at suitable height for smooth functioning ) complete all specified and directed.

Supply and fix in repairs health faucet with tube PTMT suitable for 15 mm dia pipe with 1.0 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

Supply and fix toilet paper holder brass chromium plated with flat recessed type stainless stell complete all as specified and directed.

Supply and fix tubular towel rail 20mm dia 600mm long chromium plated complete all as directed.

Supply and fix gully trap 110/125 mm dia with grating including jointing to fixed in cement concrete 1:2:4 type B1 complete all as specified and directed.

Supply and fix 75mm PVC SWR pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

Supply and fix 110 mm PVC SWR pipes single socketed, in any length with rubber ring joints fixed to wall complete all as specified and directed.

Supply and fix 75mm bore PVC SWR bends with access door of any radius complete all as specified and directed.

Supply and fix 110mm bore PVC bends with access door of any radius complete all as specified and directed.

Supply and fix 75mm bore PVC (SWR) vent cowl, complete all as specified and directed.

Supply and fix 110mm bore PVC (SWR) vent cowl, complete all as specified and directed.

Material and labour for 150 mm bore reinforced concrete pipes, class NP2, laid and jointed complete with collars with CM 1:1, complete all as specified and directed.

Material and labour for extra forming fair finished channels or drains 30 cm inner girth using extra cement incl forms, moulds, mitred/ stopped ends.

Supply and fix 1000 liters capacity white colour triple layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 20 mm size ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete all specified and directed.

Supply and fix metal gate valves with iron wheel head,screwed both ends for iron pipe, ISI Marked, as per IS: 778 of 20mm sizes gate valves complete all as specified and as directed.

Supply and fix metal gate valves with iron wheel head,screwed both ends for iron pipe, ISI Marked, as per IS: 778 of 25 mm sizes gate valves complete complete all as specified and directed.

Taking down copper/aluminum point wiring (light, fan, socket or power) complete and including (fitting and fixture such as switches, socket ,ceiling rose ,pendent ,regulators,light fittings, etc to be measured separetaly) Note:- Job including for taking out old gutties,screw,nails,casing caping/conduit etc and making good to disturbed surface of wall ,floor etc including to match with the existing surface.

Material and labour for point wiring with 1.5 sq mm FRLS single core PVC insulated unsheathed 1100 V grade with multistranded copper conductor drawn through PVC conduit with all accessories concealed in the wall /roofs etc and including provision of 1.5 sq mm PVC insulated and unsheathed copper conductor as earth continuity conductor and connected to common earth dolly all as s specified and directed for following:-

One light/Fan point controlled by one switch.

One socket 3 pin outlet 5 amp on independent board.

One 3 pin socket outlet 5 amp on the same board with other switches.

All as per serial item No 103 here-in-before but with copper conductor cable for one 3 pin socket outlet 15 amp independent board with cable 2.5 sq mm 2.5 sq mm copper cable as earth continuity conductor complete all as specified and directed.

Supply and fix in repairs moduler switch 1 way 6A 1 module complete all as specified and directed.

Supply and fix in repairs moduler switch 1 way 16A 1 module complete all as specified and directed.

Supply and fix in repairs ceiling rose three terminal/PVC polycarbonate, isolated body complete all as specified and directed.

Supply and fix in repairs moduler socket 6A/16A, 2/3 pin combined,2 module complete all as specified and directed.

Supply and fix in repairs moduler socket 6A 2/3 pin combined,2 module complete all as specified and directed.

Supply and fix in repairs moduler fan regulator 120 W. 2 module complete all as specified and directed.

Supply and fix in repairs moduler white cover plate with frame. 3 module complete all as specified and directed.

Supply and fix in repairs moduler white cover plate with frame. 6 module complete all as specified and directed.

Supply and fix in repairs moduler metal flush box 3 module complete all as specified and directed.

Supply and fix in repairs moduler metal flush box 6 module complete all as specified and directed.

Supply and fix in repairs LED Batten for LED tube light with 01 No of LED tube 18 Watt fixed on two Nos of Square Block with twin core copper flexible wire and including taking down old type tube light fitting etc complete all as specified and directed.

Supply and fix in repairs LED luminaire 600mmx600mm 35/36 watt, 220V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holder and LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

Supply and fix in replacement sub main wiring drawing through PVC conduit concealed in wall/roof with two single core 4 sq mm and one run of 4 sq mm as earth wire of stranded copper conductor PVC insulated and unsheathed cable of 1100 volts grade complete all as specified and directed.

Supply and fix in replacement sub main wiring drawing through PVC conduit concealed in wall/roof with two single core 6 sq mm and one run of 6 sq mm as earth wire of FRLSH stranded copper conductor PVC insulated and unsheathed cable of 1100 volts grade complete all as specified and directed.

Supply and fix in repairs MCB DB SPN 12 ways double door with 240 Volt, 200 amps rated bus bar with all accessories flush in the wall including taking down old Unsv DBs by dissconnecting of electrical coonection any type including connection in new DBs by using flexible pipe suitable size and making good and match with the existing surface of wall etc complete all as specified and directed.

Supply and fix in replacment of sheet metal enclosure 4 ways double door triple pole and neutral with 415 Volt, 200 amps rated bus bar with all accessories fixed in the wall including taking old DBs any type and cap and making good and match with the existing surface of wall complete all as specified and directed.

Supply and fix in replacment of vertical type DB ,double door Suitable for isolated neutral bar 4 ways,IP 43 protection, Door earthing,mechenical impact strength IK 08 insulated busbar assembly ,fixed in the wall with suitable nut and bolt including 4 pole MCCB 125 Amp 16 KA fixed in DBs as incommer three phase supply fixed in the wall including taking old DBs any type and cap and making good and match with the existing surface of wall complete all as specified and directed.

Supply and fix in repairs of Isolater TPN 4 pole 100 amp 415volts, complete all as specified and directed.

Supply and fix in repairs MCB single pole and neutral 35-63 amps, 240 Volts, complete all as specified and directed.

Supply and fix in replacement of MCB 6 to 40 amps single pole 240 Volts, Complete all as specified and directed.

Supply & fix in repairs exhaust fan 300 mm sweep single phase 230/240 V made of steel body with frame and louver shutter copper winding fixed in wall with nuts and bolts by making of suitable arrangement and making good complete all as specified and directed by engineer-in-charge.

Supply and hanging /fixing in repair ceiling fan 1200 mm sweep AC Supply (Input Voltage Range ; 120 to 280V), BLDC type, 5 star rated, BEE and ISI Marked super enamelled, copper winding of 'B' class insulation, single phase, minium 26W (± 10%), Temperature rise 40 degree maximum without remote with and including operative based capacitive regulator, 03 No blades, down rod including accessories, white colour, total harmonic less than 10%, 5 speed, hanging in position including making connection with flexible cord three core twisted copper conductor of suitable size from ceiling rose to fan complete all as specified. Note :- (i) Sereial Number as issued by Engr-In-Charge of celing fan and GE Office name shall also be written on fan with red colour permanent marker cost for the same shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account.

Supply & fix in replacement of aesthetically designed LED security light luminiareis of 35 watts system wattage for energy saving having IP 66 degree of protection,with minimum system efficiency as>85%,made of pressure die casting aluminum housing power coated in graphite grey and heat resistant toughened glass with excellent thermal management LED should have lens optics and vandal proof prismatic poly carbonate covers for ensuring efficient optics and uniform distribution of light Fitting should have operating voltage range of 120-270 VAC,THD<10%,P.F>.95 The fitting should have in built surge protector of 5 KV and CRI>70 with CCT 5700 K including 40mm dia GI pipe light grade of 1.5mtr length with necessary clamp & nut bolts complete all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point complete all as specified or indicated including testing on completion.

Supply and fix in repairs moduler white cover plate with frame 4 module complete all as specified and directed.

Supply and fix in repairs moduler white cover plate with frame 8 module complete all as specified and directed.

Supply and fix in repairs moduler metal flush box 4 module complete all as specified.

Supply and fix in repairs moduler metal flush box 8 module complete all as specified.

Supply & laying cable XLPE insulated screened PVC bedded galvanized steel strip or wire, armoured , electric power cable (heavy duty)1100 volts grade with stranded aluminium conductor, cross-sectional area 10 sqmm, 4 core laid in trenches complete all as specified and directed .

Supply & laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50sqmm 3.5core complete all as speified and directed.

Material and labour for sand cushioning in layers of sand before and after laying of cable in trenches complete all as specified and directed. Note:-Punned thickness to be measured for payment.

Supply and laying only unreinforced Precast concrete cable cover of class LV type 1 flat size 250 mm x 150 mm x 40mm for protection for cable complete all as specified and as directed.

Supplying and laying un-reinforced precast concrete cable cover class LV, flat, Type 2 size 300 mm x180 mm x 40 mm complete all as specified and directed.

Supply and fix of star delta starter for max motor output at 415 Volt, 3 phase suitable for 3 HP motor relay range 3.8-6 Amps in sheet metal enclosure for 3 phase complete all as specified and directed.

Supply and install hi wall split units indoor/outdoor of capacity 2.0 TR with copper condensor coil inverter AC complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality with minimum 4 star rating and EER 3.2 of capacity complete all as specified and as directed.

Supply and install Electronic wall mounting type stablizer suitable for AC upto 2.0 TR Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type and designed for input variation between 170 volt to 250 volt with output voltage stabilized at 230 volt with accuracy of ±2.5% and of capacity 5.0 KVA complete all as specified and as directed.

AARTI ENTERPRISES (BID ID -3372462)

M/s Gee Cee Enterprises (BID ID -3376648)

NILESH SUBHASH KARALE (BID ID -3373640)

S and G Construction (BID ID -3375564)

Laxmi Enterprise (BID ID -3378119)

NEELKANTHA ASSOCIATE (BID ID -3376968)

NAVIN K LAKHANI (BID ID -3372927)

TAKHUBHA KANUBHA JADEJA (BID ID -3373117)