KMC/WS/KBPS/JOKAPS/T-03R/25-26

SUPPLY, DELIVERY OF 1. PUMP: HORIZONTAL SPLIT CASING SIDE SUCTION DELIVERY 1000 CUM/HR. 180 KW CENTRIFUGAL PUMP MOTOR SET FOR WATER SUPPLY PUMPING STATION WITH FOLLOWING SPECIFICATIONS A). FLUID TO BE HANDLED: CLEAR DRINKING WATER B). REQUIRED FLOW RATE (CAPACITY): 1000 CUBIC METER/HOUR C). REQUIRED HEAD: 36 METER WC HEAD D).TYPE OF PUMP: CENTRIFUGAL, HORIZONTAL SPLIT CASING E). MINIMUM SUCTION/DELIVERY DIAMETER SIZE OF PUMP: 350MM/300MM 2. MOTOR: 3-PHASE, 415V?10%, 50HZ?5%, 6 POLE, 180 KW, IE3, TEFC, HORIZONTAL FOOT MOUNTED (B3), CONTINUOUS DUTY (S1), SQUIRREL CAGE INDUCTION MOTOR 3. COMMON BASE FRAME FOR PUMP-MOTOR SET &COMPANION FLANGES FOR BOTH SUCTION AND DELIVERY SIDE OF PUMP.

Installation & Commissioning of the Pump motor set

BUILDING WORKS (B) DISMANTLING, CUTTING CHASE, HOLES ETC 2. Dismantling all types of plain cement concrete works, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m In ground floor including roof. (a) upto 150 mm. thick

BUILDING WORKS (B) DISMANTLING, CUTTING CHASE, HOLES ETC 2. Dismantling all types of plain cement concrete works, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m In ground floor including roof (b) above 150 mm. thick

BUILDING WORKS ( C ) BRICKWORKS, CONCRETE WORKS Etc. A. BRICK WORKS 1. Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand.

BUILDING WORKS ( C ) Brickworks,Concrete Works etc B. CONCRETE WORKS 1. Cement concrete with graded jhama khoa (30 mm size) excluding shuttering In ground floor and foundation (a) 1:3:6 proportion

BUILDING WORKS ( C ) Brickworks,Concrete Works etc?36.Hire andlabour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor).(When the height of a particular floor is more than 4 m the equivalent floor height shall be taken as 4 m and extra for works beyond the initial 4 m ht. shall be allowed under 12 (e) for every 4 m or part thereof).(c) Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete work

BUILDING WORKS ( C ) Brickworks,Concrete Works etc 10?. Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes.(i) Pakur Variety

BUILDING WORKS ( C ) Brickworks,Concrete Works etc.40..Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction.(a) For works in foundation and upto roof of ground floor/upto 4 m.(i) Tor steel/Mild Steel.I. SAIL/ TATA/RINL.

SECTION 1. ------------BUILDING WORKS (I) PLASTERING, POINTING ETC. A. ORIGINAL WORKS 1.Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface](ii) With 1:4 cement mortar (a) 20 mm thick plaster

MS PLATE AS PER IS : 2062-2011/ LATEST REVISION, MAKE : SAIL/TATA/JINDAL C) ABOVE 10MM UPTO 20 MM THICKNESS

CHAPTER - II LAYING & JOINTING PIPES, SPECIALS ETC.2.1 C.I. / D.I. Pipe & Specials 2.1 C.I. / D.I. Pipe & Specials 2.3.5 Fabricating M.S. pipes of different diameter in shop out of 8mm to12mm thick M.S plates supplied depart-mentally, cutting the plates to exact size & shape by gas cutting device and/or by adopting any other approved type of mechanical means, bending the same in true curvature by template and rolling machine of approved design including proper marking, levelling joints followed by electric arc welding as per relevant I.S. specification - longitudinal and circumferential, as necessary, usiug standard electrodes including edge preparation, electricity charges and hydraulic testing of the fabricated piece all complete as per speci-fication and direction of the Engineer-in-Charge. [The Engineer-in-Charge shall approve the electrodes for arc weldingbefore use.]a) Diameter from 450 mm & upto 600 mm.ii) 10mm thick plate.

CHAPTER - VIII SUPPLYING OF MATERIALS Supply of M.S. Flange (slipper type) as per IS-6392 TABLE 17 Thickness - 20mm -22mm NB Diameter in mm 300

CHAPTER - VIII SUPPLYING OF MATERIALS Supply of M.S. Flange (slipper type) as per IS-6392 TABLE 17 Thickness - 20mm -22mm NB Diameter in mm 350

CHAPTER - II LAYING & JOINTING PIPES, SPECIALS ETC.2.1 C.I. / D.I. Pipe & Specials 2.1 C.I. / D.I. Pipe & Specials 2.3.7Supplying and fabricating 20 mm to 32mm thick (finished thickness) M.S flange. properly ribbed, one face machined, including drilling holes as perstandard table, fitting and fixing the same with M.S. pipe by electric arc welding as per relevant I.S. specification using standard electrodes and direction of the Engineer-in-Charge. [ The Engineer-in-Charge shall approve the electrodes for arc welding before use] 500mm dia

SUPPLY AND DELIVERY OF MILD STEEL FABRICATED DOUBLE FLANGED SLANTED SEATED TILTING DISC CHECK VALVE(NON-RETURN VALVE WITH BOTH SIDE COUNTER WEIGHT AND HYDRAULIC DAMPER) SZE 500 MM. FACE TO FACE LENGTH- 230 MM, OD= 678 MM, PCD= 620 MM,THICKNESS= 35 MM. HOLE DIA= 28 MM. NO. OF HOLES= 20,SHAFT DIAMETER= 50MM

MILD STEEL FABRICATED DOUBLE FLANGED BUTTERFLY VALVE OF PRESSURE RATING PN16 WITH SS FABRICATED SHEET PLATE IN THE INNER DIA. AND FLAP PORTION INCLUDING HEAVY DUTY GEAR BOX ATL 00/L/S2E, GEAR RATIO450:1,RATED OUTPUT TORQUE 15000NM, VALVE'SSHAFTDIA.50MMANDACTUATOR MOUNTING BASE ARRANGEMENT AS PERIS: 13095/1991 & FLANGE DRILLED AS PERAWWA C207-13CLASSD PCD-620 MM OD-678MM ID-500MM F TOF(OUTER)- 150MM FLANGETHICKNESS-35 MMHOLESDIA.- 28 MM NO. OF HOLES- 20 NOS

SUPPLY & DELIVERY OF SYNCROPACK ELECTRICAL MOTORIZED ACTUATOR (WITH FL4 MOUNTING) WITH INTEGRAL CONTROL AND STARTER, SYNCHRO PHASE PROTECTION ANTI HAMMER PROTECTION, SINGLE PHASEPROTECTION , JAMMED VALVEMOTORPROTECTION,2 NO.TORQUE/UNIT SWITCHES(SPARE 1 NO/1NC CHANGEOVER CONTACTS) 4 NO AUXILERY LIMIT SWITCHES (SPARE 1NO/1 NCCHANGE OVER CONTACTS)AND CONTINUOUS POSITION INDICATOR (MECHANICAL AND ELECTRICAL) WITH HAND WHEEL DRIVE AND HAND AUTOLEVER, AUTO LEVER SUITABLE FOR BUTTERFLY VALVE.(INCLUDING DIGITAL POTENTIO METER) O/P TORQUE 600 NMOIP SPEED 12RPM

RUBBER EXPANSION JOINT FABRICATED WITH EPDM HIGH QUALITY RUBBER EXPANSION/COMPRESSION BODY AND ADJUSTABLE FOLLOWER MS FLANGED DRILLED AS PER AWWAC207-L3 CLASS D COMPLETE ASSEMBLED UNIT WITH GALVANIZED STUD ANDNUTS.PCD-620MM OD-678MMID-500MMFTO F(OUTER)-300TO 3JOMM (FLEXIBLE) FLANGE THICKNESS- 40 MM HOLES DIA.- 28 MM NO. OFHOLES-20 NOS

GATE VALVE:: 500 MM DIA. DOUBLE FLANGED DUCTILE IRON ELECTRICALLY SPINDLE TYPE CONFORMING TO IS: 14846 FOR PN 1.6.

CABLE GLAND SUPPLYING OF FOLLOWING XLPE INSULATED ALUMINUM CONDUCTOR ARMORED CABLES OF 1.1KV GRADE AS PER IS 7098 (PART 1) 1988 WITH UP TO DATE AMENDMENTS. (RATE IN RS. PER MTR) 3CORE 300 SQMM

Laying on Cable Tray.Laying of cable as below, on existing Cable Tray and binding with suitable size GI wire.(iii)Above 150 sqmm

Compression Glands.Supplying and fixing compression type gland complete with brass gland, brass ring & rubber ring FOR dust & moisture(proof entry of XLPE/PVC armoured cables as below : FOR 4 core.(xiii)upto 240 sqmm

SUPPLY OF COPPER BUSBAR FOR ELECTRICAL POWER DISTRIBUTION

Finishing cable ends.(b)Finishing the end of following XLPE/PVC armoured cables by crimping method incl. supplying and fixing solderless socket (Dowels make), tapes, anticorrosive paste & jointing materials.3... core 300 sqmm cable

SUPPLY OF 3 POLE MCCB THERMAL MEGNATIC RELEASE TYPE 400-500A

SUPPLY OF INDOOR TAPE INSULATED RING TYPE LOW TENSION CURRENT TRANSFORMER OF FOLLOWING RATING 400/5

Equipment earthing.Connecting the equipments body to earth busbar incl. S & F 50 mm x 6 mm Galvanized (HOT Dip) MS flat on wall/floor with GI saddle as required and connection to equipments with incl. drilling holes, bolts, nuts,washers etc.

SUPPLY OF MOVING IRON TYPE ANALOG AC AMMETER 0-30A

SUPPLY OF COPPER CONDUCTOR, PVC INSULATED ARMORED 1100 VOLTS GRADE CONTROL CABLE OF SIZE 2.5 SQMM X 10 CORE.

SUPPLY & DELIVERY, INSTALLATION & COMMISSIONING OF 3 POLE AC POWER CONTACTOR OF OPERATIONAL CURRENT 550 AMPERE, SUPPLY VOLTAGE 415 V, AUXILIARY CONTROL CONTACT 1NO, 1NC, MODEL CK11CE311, MAKE GE

Supply and delivery of Front mounted add-on auxiliary contractor block(Make: L & T/ABB/Schneider/Simence/ GE) of the following types:9 to 80 Amp, 2N0+2NC

Sub Total