SPECIAL REPAIR TO BLDG NO-522 STN MEDICARE CENTRE, PROVN OF LIGHTING AT AB POINT OF 16 SQN, TOWER AIR CONDITIONERS FOR ATC TOWER FLAME PROOF LIGHTS FOR WSA AND DSAs ALONGWITH ACS OF 2 TR CAPACITY FOR EQPT STORE AT AF STN BHUJ

Amount

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) and removing rubbish off the MD land complete all as specified and directed by Engineer-in-Charge.

Material & labour for 50mm thick PCC 1:3:6 C-0 using 12.5mm graded crushed stone aggregate as in roof padding over a coat of cement slurry incl water proofing compund complete all as specified and as directed by the Engr-in-Charge.

Material & labour for 10mm thick screed bedding in cement mortar 1:3 on concrete surfaces, finished Fair & even including mixing water proofing compund as per manufacture;s instns (WPC to be measured seperately as supply only) complete all as specified and directed by Engineer-in-Charge.

Material & labour for applying a priming coat of cold bitumen primer @ 0.30 ltr/sqm as per para 11.44.5 of MES SSR Part-I complete all as specified and directed by Engineer-in-Charge.

Material & labour for APP based polymeric membrance minimum weighing 3kg/sqm and minimum 3 mm thick reinforced with polyster non wove fabric 9wt. Not less than 150 gms/sqm) with mineral finished land on primed surface shall be laid ny torch application method and the enitre surface shall be finally painted with one coat of bituminious paint incl taking down old tarfelt sheet/membrane any type with plaster and debris thrown away outside MD land complete all as specified and directed by Engineer-in-Charge

Supply only Intergal waterproofing compund ISI marked complete all as specified and directed by Engineer-in-Charge.

Removing of existing water tank of capacity 500 lit, refixing the same after completing the water proofing treatment etc complete all as specified and directed by Engineer-in-Charge.

Removing of existing water tank of capacity 1000 lit, refixing the same after completing the water proofing treatment complete all as specified and directed by Engineer-in-Charge.

Supply & fixing 1000 ltr rotational moulded polyethylene water storage tanks (cylinderical vertical with closed top) hoisted and fixed in position upto 12m height of slab complete all as specified and directed by Engineer-in-Charge.

Cleaning & removing all scale and dirt etc from PVC water tank and from mouths of circulating pipes etc of capacity exc. 250 ltrs and not exc 500 ltrs including disconnecting and refixing all parts required to be disconnected for cleaning of the tanks including mentioning date of cleaning with synthetic enamel paint on water tank complete all as specified and directed by Engineer-in-Charge

Cleaning & removing all scale and dirt etc from PVC water tank and from mouths of circulating pipes etc of capacity exc. exc 500 ltrs and not exc 1000 ltrs including disconnecting and refixing all parts required to be disconnected for cleaning of the tanks including mentioning date of cleaning with sybthetic enamel paint on water tank complete all as specified and directed by Engineer-in-Charge

Taking up or down steel tubing and connection incl cleaning for refining of the following bore of pipe complete all as specified and directed by Engineer-in-Charge :-

15mm bore

20mm bore

25/32mm bore

40/50mm bore

Supply & fix CPVC pipes ISI marked, IS-15778 with all fittings for hot and cold water, fixed with solvent cement complete to walls consealed in wall making grove in wall etc and ceilings or laid in floors of following sizes (SDR-13.5 complete all as specified and directed by Engineer-in-Charge

20mm bore

25mm bore

32mm bore

40mm bore

Supply & fix in repair grating doom 125mm dia with waste hole of PTMT (minimum weight 40 grams) complete all as specified and directed by Engineer-in-Charge

Supply & fix in repair PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and directed by Engineer-in-Charge

Supply & fix in repair of UPVC ultra drain, SelFit pipes, single socketed, ISI marked, IS-13592 type 'B' in any length, jointed with solvent cement fixed in walls and floors complete all as specified and directed by Engineer-in-Charge of following size

110mm dia

75mm dia

Supply & fix UPVC junction single 'Tee' equal with door opening, ISI marked, IS-14735, jointed with solvent cement complete all as specified and directed by Engineer-in-Charge of following sizes: -

110mm dia

75mm dia

Supply & fix PVR (SWC) pipes, single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed by Engineer-in-Charge of following size

75mm bore

110mm bore

Supply & fix PVC (SWR) bends any radius complete all as specified and directed by Engineer-in-Charge of following sizes

75mm bore

110mm bore

Supply & fix in repair PVC (SWR) floor trap, plain with grating including jointing with sovent cement with 75mm outlet dia complete all as specified and directed by Engineer-in-Charge

Supply & fix in repairs 15mm size bib tap cast copper alloy, chromium plated fancy type screwed down, with capston head, screwed for iron pipe complete all as specified and directed by Engineer-in-Charge

Supply & fix in repairs 15mm size pillar taps, cast copper alloy chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed by Engineer-in-Charge

Supply & fix in repairs 15mm size single lever basin mixer with 300mm extended body and 600mm braided connection pipe (without pop-up0 Chrome Plating, Make CERA Cat No: F1020452 complete all as specified and directed by Engineer-in-Charge

Supply & fix in repairs 15mm size wall mixer, for mixing hot & cold water, cast copper alloy, chromium plated with capstan head comprising bib tap with all connected accessories, fixed complete all as specified and directed by Engineer-in-Charge

Supply & fix in repairs 15mm size stop valve or angle valve cast copper alloy, chromioum plated fancy type, screwed down, high pressure with capston head, screwed both ends for iron pipe or for union all specified and complete all as specified and directed by Engineer-in-Charge

Supply & fix in repairs 15mm size stop valve, Angle cock Make CERA Cat No. F1020201 complete all as specified and directed by Engineer-in-Charge

Supply & fix in repairs 15mm size stop valve with long shank (consealed type) cast copper alloy, chromioum plated fancy type, screwed down, high pressure with capston head, screw both ends for iron pipe or for union complete all as specified and directed by Engineer-in-Charge

Supply & fix in repairs 15mm size stop cock consealed type Make - CERA Cat No. F1020361 complete all as specified and directed by Engineer-in-Charge

Supply & fix in repairs 15mm size 2-way Bib cock with single handle and wall flange, Chrome Plating, Make-CERA Cat No: F1020163 complete all as specified and directed by Engineer-in-Charge

Supply & fix in repairs Shower Make CERA Cat No F7020110SS-1 Overhead Rain shower SS 100 x 100mm with 200mm long shower arm and wall flange complete all as specified and directed by Engineer-in-Charge

Supply & fix 20mm size gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe and including taking down old gate valve complete all as specified and directed by Engineer-in-Charge

Supply & fix 15mm size stop valve of PTMT any colour high pressure screwed for iron pipe, weight not less than 90 gms, including taking down old stop valve complete all as specified and directed by Engineer-in-Charge

Supply & fix in repairs 32mm size waste pipe, length 1.20m for wash basin/urinal/sink complete all as specified and directed by Engineer-in-Charge

Supply & fix in repairs 40mm size waste pipe length 1.20m for wash basin/urinal/sink complete all as specified and directed by Engineer-in-Charge

Supply & fix in repairs 32mm size waste coupling of PTMT for wash basin/urinal/sink complete all as specified and directed by Engineer-in-Charge

Supply & fix in repairs 40mm size waste coupling of PTMT for wash basin/urinal/sink complete all as specified and directed by Engineer-in-Charge

Supply & fix in repairs Hand shower (Health Faucet) brass chromioum plated with 8mm dia & 1 meter long flexible tube and wall hook complete all as specified and directed by Engineer-in-Charge

Supply & fix in repairs 10 Ltr capacity PVC syphonic action type flushing cistern low level with inlet ball valve, float and handle, fixed in position and connecting including taking down old cistern complete all as specified and directed by Engineer-in-Charge

Supply & fix in repairs of vitreous China wash basin including pedestal, white, flat back, size 630mm x 450mm including chromioum plated waste coupling, plug and chain, necessary brackets complete all as specified and directed by Engineer-in-Charge

Supply & fix vitreous china white wash hand basin 550mm x 450mm including all necessary fitting such as 15mm CP pillar cock fancy type, CP waste coupling 32mm dia, PVC waste pipe and brackets including supply & grouting 6 to 8 mm dia GI racket bolt at the back side of WHB and making good existing surfaces, including taking down old wash hand basin complete all as specified and directed by Engineer-in-Charge

Supply & fix vitreous china white Table Top wash basin in repairs having size 450mm x 160mm, Rectangle bowl, Snow white inn colour, including making hole as per size into the granite cutting etc complete all as specified and directed by Engineer-in-Charge

Supply & fix flastic water closet seat cover, white or black colour closeed pattern with flat bottom including taking down old seat cover complete all as specified and directed by Engineer-in-Charge

Supply & fix polyethylene water tank cover with hinges suitable up to 2000 ltr tanks, including taking down old water tank cover complete all as specified and directed by Engineer-in-Charge

Supply & fix in reparis 15 mm size brass chromium plated zig zag type connector (coupling) for connecting wall mixer and GI tubing complete all as specified and directed by Engineer-in-Charge

Supply & fix in reparis 6 mm thick corner glass self with aluminum/ SS railing incl brackets for fixing (size 300 mm X 300 mm) etc complete all as specified and directed by Engineer-in-Charge

Supply & fix in repairs 6 mm thick rectangular galss self with aluminium/ ss railing incl brackets for fixing (size 450mm x 150mm) etc complete all as specified and directed by Engineer-in-Charge

Supply & fix vitreous china EWC wall mounted (white) Size of EWC-525x365x360 mm incl taking down old water closet (in repairs) Make CERA Cat No : S1043169, Wall Hung EWCs with including Slim soft close seat cover, Square bowl, concealed P Trap, flushing cistern snow white in colour, including makin good etc complete all as specified and directed by Engineer-in-Charge

Supply & fix in repairs vitreous China squatting pan, 'Orissa' pattern size 580x 440 mm white, with integral foot rests flushing cistern and flush pipe complete all as specified and directed by Engineer-in-Charge

Supply & fix in reparis vitreous china urinals, bowl type ( black or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1;2, securing to plugs with and including 60mm long brass screws, pointing araound urinal back in cement ; fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge incl all ppipe and fittings upto waste pipe complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75mm to 10mm dia pipe complete all as specified and directed by Engineer-in-Charge.

Demoliton of reinforced cement concrete in any position and in any description not otherwise specifically provided for complete all as specified and directed by Engineer-in-Charge

Material & labour for separating, scraping and cleaning of reinforcement (Demolition of concrete measured separately) complete all as specified and directed by Engineer-in-Charge

Material & labour for reinforced cement concrete in (20mm graded stone aggregate) for chajjas or similar wks complete all as specified and directed by Engineer-in-Charge

Material & labour for reinforced cement concrete in (20mm graded stone aggregate) for Beams, cantilevers, bresssummer,lintels over 1.5m span complete all as specified and directed by Engineer-in-Charge

Material & labour for formwork with fair finished surface to side of soffits of floors, or roof beam, beam hanuchings, giders, bressummers, lintels, cantilevers, shelves incl sup-posts, overhang etc also splays bet floor and beams etc complete all as specified and directed by Engineer-in-Charge.

Material & labour for reinforced cement concrete (20mm graded stone aggregate) for columns, pillers, piers, posts and struts complete all as specified and directed by Engineer-in-Charge

Material & labour for formwork to sides of pillers, post, columns, piers and stanchions in square, rectangular fair finished surface of concrete complete all as specified and directed by Engineer-in-Charge

Material & labour for TMT bars 8 mm dia and over in reinforcement, cut to length, bent to shape required including cranking and bindling with mild steel wire (anneled) not less than 0.9 mm dia for stirrups complete all as specified and directed by Engineer-in-Charge

Material & labour for TMT bars 10 mm dia and over in reinforcement, cut to length, bent to shape required, including cranking and bindling with mild steel wire (anneled) not less than 0.9 mm dia for stirrups complete all as specified and directed by Engineer-in-Charge

Material & labour for micro concrete to existing concrete sturcture including proper tight leak proof shuttering SPl polimer modified cementitious, low pemeable" free flow' no shrink self compacting micro concrete shall be grade M50 as per recommended w/c ratio and pouring as per the required thickness complete include scaffolding, formwork upto height 15m for additonal reinforcement drilling holes etc any number as per direction of Enge-in-charge included in this items etc complete all as specified and directed by Engineer-in-Charge.

Demolition of precast concrete block walling of any description built in cement mortar complete all as specified and as directed by Engineer-in-Charge.

Material & labour for precast cement concrete block masonary with solid blocks exc 10cm in width Type C1 (1:3:6) 20mm graded and setting in cement mortar 1:6 incl toothing & backing for old and new wall etc complete all as specified and directed by Engineer-in-Charge

Taking down cement plaster on brick or stone walls etc including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge

Material & labour for 10 mm thick rendering in CM 1:6 on concrete surfaces / fair faces of brick masonary wall, finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

Material & labour for applying two coats of oil bound distemper over a coat of primer on previously untreated surfaces of wall including preparation complete all as specified and directed by Engineer-in-Charge

Material & labour for 15 mm thick cement plaster on stone or concrete surfaces in CM 1:4 mixed with water proofing compound @ 3% by weight of cement including 10m height steel scaffolding complete all as specified and directed by Engineer-in-Charge. [Note:- WPC shall be measured and paid separately ]

Supply of integral water proofing compound complete all as specified and directed by Engineer-in-Charge

Material & labour for preparing new plaster surfaces of walls applying one coat of weather coat primer and two coats of weather proof acrylic emultion paint all as per manufacturers instructions and directed including 12m height steel scaffolding complete all as specified and directed by Engineer-in-Charge

Material & labour for preparation of Old plastered or unplastered washing, rubbing down and stopping of distemper and painted surfaces of walls and applying one coat of distemper oil emulsion over primer ( as approved by GE) complete all as specified and directed.After Perodical service of the Qtr/building the contractor will clean all the paint marks from glass panes , electric switch boards and fittings , doors windows and should clean the floor , dado and all scraped material debris shall thrown away MOD land complete all as specified and directed by Engineer-in-Charge.

Material & labour for rendering 10mm thick in CM 1:4 on fair faces of brick work of ceiling complete all as specified and directed by Engineer-in-Charge.

Material & labour for 3mm thick one coat of wall care putty on new ceiling surfaces incl preparation complete all as specified and directed by Engineer-in-Charge.

Material and labour for preparation of new plastered surfaces on ceiling and applying two coats of oil Emulsion distemper over a coat of alkali resistant priming paint complete all as specified and directed by Engineer-in-Charge but on ceiling

Material & labour for preparation of Old plastered or unplastered washing, rubbing down and stopping of distemper and painted surfaces of Ceiling and applying Two coats of white wash complete all as specified and directed.After Perodical service of the Qtr/building the contractor will clean all the paint marks from glass panes , electric switch boards and fittings , doors windows , should clean the floor , dado and all scraped material, debris shall thrown away MOD land complete all as specified and directed by Engineer-in-Charge.

Material & labour for complete removal of existing treatment on surfaces of wall, chajjas etc in any position washing down with water and cleaning the surface from all loose dirt chalk grease fungi algal flakes etc and applying Two coat of weather proof acrylic emultion paint over one coat of primer all as per manufacturers instructions and directed including scaffolding complete all as specified and directed by Engineer-in-Charge

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) and removing rubbish off the MD land complete all as specified and directed by Engineer-in-Charge.

Material & labour for 25 mm thick cement concrete type B-0, 1:2:4 using 12.5mm graded aggregate in sub base of floors etc complete all as specified and directed by Engineer-in-Charge.

Material & labour for glazed digital ceramic coloured tiles Ist quality in vertical surfaces such as in skirting and dados 350x250x7mm/450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and icluding plaster in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

Material & labour for screed bed or bedding layer or mortar 15mm layer of mortar 15mm thick for laying floor /dado finishes in CM 1:6 complete all as specified and directed by Engineer-in-Charge

Material & labour for non skid ceramic coloured tiles 7 to 8mm thick (sqaure/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm as per IS - 13755 in floor, set and jointed in neat cement slurry and pointed in coloured cement to match over and including screed bed 15mm thick in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

Material & labour for hardcore of broken stone or boulders gauge exc 63 mm but n exc. 100 mm , deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface complete all as specified and directed by Engineer-in-Charge.

Material & labour for 100 mm thick cement concrete type C-2, 1:3:6 (40mm graded aggregate) as in flooring ,finishing even and smouth wiyhout using extra cement complete all as specified and directed by Engineer-in-Charge..

Material & labour for in repairs for 18-20mm thick granite, Z black (table rubbed and polished) for platforms, wall lining (veneering to wall), gates, cills and in similar items laid over and including 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixutre of pigment to match with shade of granite external edges rounded, making groves, moulding , using partation in self etc complete all as specified and directed by Engineer-in-Charge.

Material & labour for providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows,ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight,mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling,Aluminium composite panel,C.P. brass/ stainless steel screws, complete all as specified and directed by Engineer-in-Charge.

Taking down Chowkats or frames not exc. 1.5 Sqm each, with shutters (without taking off shutters from the frame) complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhat or frames with shutter (without taking off shutters from the frames) exc 1.5 sqm but n.exc 4.00 sqm complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description exc 1 sqm but n exc 2 sqm each complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description n exc 1 sqm complete all as specified and directed by Engineer-in-Charge.

Taking down chowkats / frame with shutters for window any type steel / aluminium etc, Size exc 0.50 sqm but n.exc 3 sqm each with shutters and refixing the same without any damage incl making good etc complete all as specified and directed by Engineer-in-Charge.

Supply & fix 100 mm Extruded powder coated aluminium alloy handles fabricated type, anodised complete all as specified and directed by Engineer-in-Charge.

Supply & fix 100 mm butt hinges, extruded powder coated aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 ISI marked complete all as specified and directed by Engineer-in-Charge.

Supply only rubber gasket for fixing of glass complete all as specified and directed by Engineer-in-Charge.

Supply & fix aluminum alloy wire cloth , 0.45 mm nominal dia of wire and avg width of aperture 1.40mm and fixed with aluminum stapples complete all as specified and directed by Engineer-in-Charge.

Supply & fix 5mm to 5.5 mm thick sheet glass ordinary quality area n exc 0.50 Sqm in each pane and glazing for fixing in Plywood any type in any shape and size circular cutting incl waste ,wood ,plywood and aluminum frame work incl fixing glass 30mm dia knob on sliding glass complete all as specified and directed by Engineer-in-Charge.

Supply & fix 3 mm thick sheet glass ordinary quality and glazing with oil putty/wooden lapping in square not exc 0.58 Sqm each in each pane complete all as specified and directed by Engineer-in-Charge.

Supply & fix 3 mm thick figure glass/ tinted glass ordinary quality and glazing with oil putty/wooden lapping in square not exc 0.58 Sqm each in each pane, lovers etc complete all as specified and directed by Engineer-in-Charge.

Material & labour for aluminium anodised grill of approved shape with opening in Heavy duty Deco grill 66mm x 80mm (diagonally) or nearest to + 5mm made out of standard aluminium moulded section of size 4.4 mm x 7mm complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs brass mortice lock, vertical type, size 100 mm , 4 levers with 2 keys complete all as specified and directed by Engineer-in-Charge.

Supply & fix 150 mm size of door handle Extruded brass handles, fabricated type polished complete all as specified and directed by Engineer-in-Charge.

Supply & fix stainless steel in repairs butt hinges medium weight SS of size 100 mm by welding / fixing with screws etc to any frame window and doors etc complete all as specified and directed by Engineer-in-Charge.

Supply & fix brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and directed by Engineer-in-Charge.

Supply & fix 200mm long brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and directed by Engineer-in-Charge.

Material & labour for 25 x 3mm FI holdfasts complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repair brass 300mm ordinary rat tail rod pettern springs including roller and roller plate complete all as specified and directed by Engineer-in-Charge.

Material & labour for floor door stopper 150mm long , of brass body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repair door closer hydraulically regulated,Aluminium (excruded section) designation No. 3,universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs double action floor spring Hydrauilically regulated made up of minimum 1.25 mm thick aluminium alloy sheeet foundation box, main body with stainless steel cover governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed by Engineer-in-Charge.

Supply & fix PVC door PDS-01 comprising of shutter and frame of Make : Rajshree/Accura Polytech Pvt Ltd (Accucel) all as shown on drg No.CEAA/TD/149 sheet No. 1/1 (PVC RIGID FOAM) , door frame/ chowkats of solid rigid foam profile FP-6030 and shutter of solid PVC foam profile FP 7114 with 4 mm thick high pressure compact laminate as infill (Panel) including necessary hardeware fittings complete all as specified and directed by Engineer-in-Charge.

Supply & fix 35mm thick 2nd class hard wood factory made plain framed, paneled shutters (any number of panels), with lock rail and panel of 9mm BWP commercial ply or 12mm veveered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (part-I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engineer-in-Charge..

Supply & fix 35mm thick 2nd class hard wood factory made glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc, with sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/ Gauge etc. Size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24(a) complete all as specified and directed by Engineer-in-Charge.

Material & labour for stainless steel 'L' shape soft closing spring hinges / Autohinge for cabinets shutters 4 hole clip on cabinet hinge nickel plated, corrosion resistant, complete all as specified and directed by Engineer-in-Charge.

Material & labour for in repairs GI push and pull channel brand of size 20"(51 CM) length for modular cabibets complete all as specified and directed by Engineer-in-Charge.

Supply & fix framed stainless steel sections as in drawers and pull up cuboards, design as approved of any size and shapes including clips and washers,etc to fix it to the prelaminated PVC sheets , plywood etc in cabinets,etc of stainless steel grade 304, all as approved and directed during execution complete all as specified and directed by Engineer-in-Charge.

Material & labour for in repairs for plywood 18mm thick grade BWR type BB fixed with screws to timber frame ,Al frame etc complete all as specified and directed by Engineer-in-Charge.

Supply only for decorative laminate type 1 of any thickness of surface finish, colour and pattern as approved, fixed with approved adhesive on plywood as per manufacturer instruction and complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs 40 mm dia cupboard knobs fixed with nut, screw and washer of mild steel bright finished complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs hasp and staple safety type of size 100 mm of aluminium anodized including taking down old hasp and staple complete all as specified and directed by Engineer-in-Charge.

Supply & fix magnetic catches for cupboard doors No.2 complete all as specified and directed by Engineer-in-Charge.

Supply & fix sliding wardrobe wheel hikido inset wardrobe system sofy close for doors (50 Kg capacity) any door thickness for 2 doors, product code 3869 ( box contents 8 pieces runner, 4 pieces dampners, 8 pieces end cap, screw packets complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs vanity Mirror cabinet for washbasin premium wall mounted storage cabinet bathroom with door multipurpose bathroom cabinet rack with mirror (white) size 54D x 35W x 12H centimeters, wall mount fix with screw / fastners, etc complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs tubular towel rail, aluminium anodised 20mm dia D type 60 CM long between flanges complete all as specified and directed by Engineer-in-Charge..

Supply & fix in repairs Toilet paper holder of brass, chromium plated fixed to walls with chromium plated (CP) brass screws complete all as specified and directed by Engineer-in-Charge.

Material & labour for in repair anodised aluminium snap grid size of grid 605mm x605mm frame work made out of 0.5mm thick GI tee 32x24mm for main, 25x44mm for cross tee and 20x20mm angle fixed on wall , powder coated finish on exposed faces of tee and angle , hung from ceiling using 2mm thick GI suspension wires spaced of 1200mm on main runners for any type POP false ceiling complete complete all as specified and directed by Engineer-in-Charge.

Material & labour for providing and fixing in repair 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat ,curved and raised moulding entricate design surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wiremesh complete all as specified and directed by Engineer-in-Charge.

Material & labour for providing and fixing in repair 10mm thick and Girth 120mm , plaster of paris ceiling (Gypsum anhydrous) to flat ,curved and raised moulding entricate design ,surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wiremesh complete all as specified and directed by Engineer-in-Charge.

Supply & lay cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty0 1100 Volts grade with standard aluminium conductor or complete all as specified and directed by Engineer-in-Charge.

50 Sqmm 3.5 Core

10 Sqmm 4.0 Core

Excavation in trenches, in any type of soil not exceeding 1.5 Mtr wide and not exceeding 1.5 Mtr in depth, laying of cable or pipes (where provided for protection of cable) etc and getting out trimming the sides, forming bottom surfaces to required level complete all as specified and all as directed by Engineer-in-Charge.

Material and labour for sand cushioning with a layer of sand 80mm thick before laying of cable and 150mm thick after laying of cable in trenches well ramming and spreading in layers complete all as specified and directed by Engineer-in-Charge.

Supply & laying un-reinforced precast concrete cable cover class LV, type - 2, flat, size 300x180x40mm complete all as specified and all as directed by Engineer-in-Charge.

Returning and filling including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick complete all as specified and all as directed by Engineer-in-Charge

Removing of surplus soil to a distance not exceeding 50 Mtrs and depositing where directed at a level not exceeding 1.5 Mtr above the starting point complete all as specified and directed by Engineer-in-Charge.

Supply & fix of tubes light grade of 50mm bore galvanised with all fitting for cable protection trenches/wall/on pole including necessary clamps sets and nut & bolts complete all as specified and directed by Engineer-in-Charge.

Supply & fix GI Pipe medium grade of 80mm bore with sufficient PCC above and under the ground compete all as specified and directed by Engineer-in-Charge including welding work for making 'T' shape of pole for mounting flood light. complete complete all as specified and directed by Engineer-in-Charge.

Supply & fix FRP junction box of size outside dimensions 250 x 250 x 160 mm with terminals, IP-65/66 protection, as approved by the EIC including connector and fixing on pole with and including MS clamps made out of 25 x 35mm MS flat iron, nut, bolts etc incl of one No of 6 Amp MCB, making internal electrical connections to MCB complete complete all as specified and directed by Engineer-in-Charge. Note: The cost of junction box installation includes making hole of suitable size for entry and exit of cable upto 96 Sqmm 3.5 Core size, making new lugs of Cables of entry and exit.

Material & labour for wiring circuit along with earth wire from Sintex box to Flood light fitting with 3 run of 1.5 Sqmm sizes FRLSH insulated copper conductor single core cable in surfaces/recessed as required including steel conduit of size 20mm dia with suitable clamps made out of 25 x 3mm thick steel flat commplete with nuts bolts and washers complete all as specified and directed by Engineer-in-Charge.

Supply & install air cooled tower AC with scroll compressor electric driven, three phase of capacity 4.0 TR complete all as specified and directed by Enginner-in-Charge

Material & labour for point wiring complete with 1.5 sqmm single core multi stranded copper conductor FRLSH PVC insulated but unsheathed cable 1100 volts grade drawn through and including rigid steel ERW conduit of 25mm dia (external) heavy duty including necessary flame proof/weather proof conduit accessories and fitting on wall/ceiling etc including sealing threaded joints in conduit accessories with teflon tape including 1.5 sqmm single core FRLSH PVC insulated but unsheathed multistranded copper conductor cable as in continious earth. Wiring shall be suitable for flame proof area s per STEC-7 for One flame proof light point controlled by one, single pole flame proof switch complete all as specified and directed by Engineer-in-Charge.

Supply & fixing LED light fitting 1x16/20 Watt flame proof, CMRI certified recommended for gas/vapour group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminium hosing with heat resistant toughened glass with LED tube light fixtures driver, holdrs, connector etc. Complete with all accessories prewired and including connecting up with three core flexible copper conductor cable in flexible steel conduit with flame proof cable glands complete all as specified and as directed by Engineer-in-Charge.

Supply & fix Flame proof LED light-High Lumen output fitting of 100 Watt with exclusive innovative designed, long life versatile pressure die cast aluminium IP65 flood light luminaire with high power LED as light source complete all as specified and directed by Engineer-in-Charge.

Supply & fix flame proof and weather proof rotary type switch, 16 Amps, 250 Volts, AC single pole (LM-6) aluminium alongwith flame proof cable entry glands CMRS certified, ISI marked complete all as specified and directed by Engineer-in-Charge.

Supply & install hi wall split air conditioner units indoor/outdoor complete with cordless remote control unit and in built air ioniser and plasma filter for better indoor air quality with minimum 5 star rating and ISEER 5.0 of capacity 2.0 TR all as specified and directed by Enginner-in-Charge. Note: Necessary T&P and outdoor stands are included in above subjected rate.

Supply & fix Voltage stabliser for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 140V to 270V with output voltage stablised at 230V with accuracy of + 2.5% and of capacity 5.00 KVA complete all as specified and as directed by Engineer-in-Charge.

Supply & fix metal clad enclosure single pole and neutral with a two pin and earth plug and socket complete with one single pole MCB of 20 Amps all as specified and directed by Engineer-in-Charge.

Material & labour for sub main wiring with two run of single core PVC insulated copper cable multi-stranded conductor 4 Sqmm drawn through in and including PVC Casing Caping of size width not less than 25mm on surface of wall/ceiling with all accessories with 4.0 Sqmm PVC insulated unsheathed copper conductor as earth wire, connected to common earth dolly complete all as directed by Engineer-in-Charge. Note: Three runs of 4.0 sqmm copper cable including PVC casing capping will be measured as one RM.

Malik Associates (BID ID -3468162)