Re-Construction and Restoration of Sh. Kedarnath Town and Surrounding Areas under CSR of Overall Infrastructure in Sh. Kedarnath along Saraswati in Distt Rudraprayag (PFC)

4C x 6 Sq.mm. CU XLPE armored cable

Supply, Installation, assembling, connection, testing & commissioning of post top light fixture, 40-45W Power Module LED, 4000K, -MOUNTED AT 3.3 METER HEIGHT POST TOP POLE, it's - Upper frame made in die-cast and sheet aluminium (thickness: 2.5mm), with threaded coupling G3/4" for fixing,Bottom frame with ring made in die-cast aluminium and two arms made in hotgalvanized steel, with flange for fixing equipped of a hole (diam. 28 mm) .Gasket between the upper and bottom frames.Painted with polyester powder coating in Metallaic Grey (As per Architectural requirement). IP Rating - IP 66.Height –690mm, Dia - 550mm, Weight - 11.5Kg, Area Exposed to Wind(S) - 0.105 m2. Power LED's Module (with CREE/NICHIA/OSRAM/SEOUL SMD type LED’s with ESD=>8kV & Ceramic package are accepted. Colour Rendering Index: Ra > 70. Electronic Power Supply for LED Module, which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection upto 1.5kv(an additional surge protection device of 10kV also provided in-built the fixture). Optics with refractive lens (Polycarbonate), UV Resistant & Shock Resistance IK08 or higher.LM80 Reported LED Lifetime is L90@ 50,000hours minimum.(same should be supported by LM 80 report from NVLAP / DAKKS accredited lab) & Estimated LED Lifetime is L80 @ 100,000 hours(Ta-25°C) minimum..LM 80 report & TM 21 calculation should be submitted to support the same.The Light fixture shall be in compliance with IEC 60598-2-3 and other safety test (Supporting Test Report from NABL accredited Laboratory should be submitted) .LM79 report should be submitted from NABL accredited Laboratory. Sample should be submitted for approval from concerned engineer-in charge.

Supply, Installation, assembling, connection, testing & commissioning of ARCHITECTURAL POLE (FOR POST TOP LIGHT) 3.3M height Pole Made in combination of hot dip galvanised mild steel pipe sections 114mm dia. & 76mm dia. Arch. cast iron Base design starts with 322mm Dia. ring, radially tapers to 215mm for a height of 70mm, which is followed by a ring of 215mm dia,, then radially tapers to 135mm for a height of 115mm .Total weight of the base is 15 Kgs. & height of the base is 235mm. Decorative Ring-1 (114/76mm dia. - 3kgs.) & Top Ring(weight- 3kgs.) are made of cast iron. Entire pole shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. After Fabrication, Entire Pole is hot dip galvanized(60 microns Minimum ) for the effective corrosion resistance . The hot dip Galvanised pole should be provided with an inbuilt junction box (Concealed) to fix 32A connectors and 6A MCB (to terminate incoming and outgoing armoured cables with glands and lulgs), at the bottom -the inbuilt box should have a flush door of suitable size. The decorative pedastal to be mounted on a suitable size steel plate. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation. wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 or appropriate BIS Standards must be vetted by Govt. approved structural engineer at the time of bid submission , however Bidder has to get the test reports of randomly chosen prototype of pole from the accredited test labs before the contract start / execution date informed by Engineer in Charge to verify the pole design. Pole & it's parts are painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint- customised colour Metallaic Grey. Adequate size cutout with opeanable hinged door should be provided on pole with necessary gasket to ensure water tight arrangement for pulling cables and installation of mcb, connectors etc, complete in all respect as per requirement and instruction of engineer in charge. Scope also includes necessary foundation, cable termination, earthing, cable entry pipes, 3 core round flexible wire from junction box to light fixture etc. all require to complete job. Inclusive cost of specially Design RCC Foundation with G.I Nut & Bolt etc as required.

3.3M HEIGHT HERITAGE SMART POLE 3.3M height Pole Made in combination of Multiple Modules made of mild steel pipe sections 219mm dia. & multiple suitable Cast Iron embellishments like base & rings.Smart features/services such as CCTV Dome type camera, PAS-2nos.(only provision), USB charger, SOS emergency button, WIFI device/router should be inbuilt inside the pole .Entire pole shall be made to provide pleasing aesthetics as approved by Concerned Engineer in-charge. After Fabrication, MS pipe modules are hot dip galvanized(60 microns Minimum ) for the effective corrosion resistance . The hot dip Galvanised pole should be provided with an inbuilt junction box to fix 32A connectors and 6A MCB, at the bottom - the inbuilt box should have a flush door of suitable size. The decorative pedastal to be mounted on a suitable size steel plate. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation. wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 or appropriate BIS Standards must be vetted by Govt. approved structural engineer at the time of bid submission , however Bidder has to get the test reports of randomly chosen prototype of pole from the accredited test labs before the contract start / execution dated informed by Engineer in Charge to verify the pole design. Pole & Cast iron parts are painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint. : Inclusive Cost of Specially Design RCC Foundation With GI Nut & Bolte etc as required. Price shall be inclusive of following items CCTV - 2Nos. (Each pole) S.I.T.C. of 4 MP or better high quality imaging Dome camera with range of 2.8 to 4 mm and 10 mm to 12 mm varifocal lens with low light performance via powered 120 DB WDR 1/3" CMOS or better image sensor , minimum illumination - colour 0.30 Lux , mono 0.1 Lux with IP67 and IK 10 rating, IR distance 30 mtrs or above (Internal/ External) . Image Sensor : 1/3" Progressive Scan CMOS or better Resolution :2560 X 1440; 30fps @ 4MP (2560×1440), higher Compression : a. H.265 MP, M-JPEG H.265 , WDR 120dB, Analysis(edge based) - following rule based alarms and tracking: Line crossing, Enter / leave field, Follow route, Loitering, Idle / removed object, People counting, Crowd density estimation, 3D tracking. Security HTTPS / IP Filter / IEEE 802.1X ,. Certification: CE, UL, FCC,ONVIF.Protocol, ISO 14001, CUL (for temperatrue), IEC-62676-5, TCP/IP, UDP, DHCP, NTP, RTSP, PPPoE, DDNS, SMTP, FTP, UPnP, Unicast, Multicast, ICMP, HTTP,HTTPS, DNS, DDNS, RTP, RTCP, IGMP, 802.1X, QoS, Ipv4, Ipv6, two way full Duplex Audio Comminication ,time stamp, text overlay, flip & mirror, ROI, Saturation, Brightness, Chroma, Contrast, Wide Dynamic,Sharpen, white balance, video rotation, Scheduled profile settings, AGC, ONVIF: Profile S. environmental rating IP66 and IK 10 Rated, Defog feature. Operating Temperature - 30 °C to + 50. WiFi Supply installation testing and commisioning of wi-fi access point for outdoor to provide wireless network connectivity shall have network interface of 10/100/1000 Ethernet Ports (2 nos), maximum bandwithh 450 Mbps in 2.4 GHz band and 1000 Mbps or above in 5 GHz band and Wi-Fi Standards shall be 802.11 a/b/g/n/r/k/v/ac including Wireless Security WEP, WPA-PSK, WPA-Enterprise (WPA/WPA2, TKIP/AES), possibility to create VLAN for isolation of guest trafic to admin data trafic.Maximum Power Consumption: 9W, Operating Temperature : -40 to 70° C,Power Supply: 48V, 0.5A PoE Gigabit Adapter, Certifications: CE, FCC, IC, Guest Traffic Isolation, Concurrent Clientsand VLAN can be done. SOS -Consisting of SITC ofoutdoor panic/ emergency switch with addressable input module, has input voltage 15 V DC to 33 V DC, also detects Standby,With inbuilt Isolator Line monitoring when operating with EOL resistor, Contact monitoring Voltage monitoring, Individual monitoring of the two inputs Triggering in the event of line interruption, Triggering in the event of a short circuit. USB charger Waterproof USB Dual Charge Socket with 5V DC Output.USB Input Voltage Range,12-24V,USB Output Voltage 5V +/- 5%,Output Current-2x 2.1A (4.2A Total) Raiting,IPX6 waterproof,Metals-316 stainless steel,Plastics,ASA,Internal Coating-Anti-corrosion,External Coating-UV resistant.

Supply, Installation, assembling, connection, testing & commissioning of LED FIXTURE - Ground burried 10-15W,LED,3000k, IP 68 The housing in light weight, made of high strength die cast aluminium and coated by static powder making it weather resistant.Protection screen in tempered glass with high impact resistance . Premium thermal management by high heat conductivity aluminum alloy and thermal fins. SS Cover. Pure Polyester powder coating. Precise structure and multi-protection silicon rubber seal guarantees the fixture IP68 rated. Height – 135mm, Dia.-210mm, Weight - 2.5Kgs. Power LED Module with high efficacy LED's, on Printed Circuit Board with metal core plate. CRI > 80,P.F>0.9,voltage input AC100-277V,50/60Hz. In-Built Electronic Power Supply for LED Module,which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection. Estimated LED Lifetime is 70,000 hours minimum. LM80 report from LED Manufacturer . Light fixture Lumen output is 650-750Lumens. LM 79 Report should be submitted from from UL/NABL Authorised Laboratory. Sample Should be submitted for concerned engineer incharge for approval of light fixture.

Supply, Installation, assembling, connection, testing & commissioning of LED Light FIXTURE - 3W,LED,Ground Recessed Light,3000k IP 67 Light (Range of LED Wattage : 3-8 W) The housing in light weight, made of high strength die cast aluminium and coated by static powder making it weather resistant.Protection screen in tempered glass with high impact resistance(IK 08 or higher) . Premium thermal management by high heat conductivity aluminum alloy and thermal fins. SS Cover. Pure Polyester powder coating. Precise structure and multi-protection silicon rubber seal guarantees the fixture IP67 rated. Length – 231mm,Depth – 110mm, Width-90mm, Weight - 1.7Kgs. Power LED Module with high efficacy LED's, on Printed Circuit Board with metal core plate,P.F>0.9,voltage input AC100-277V,50/60Hz. In-Built Electronic Power Supply for LED Module,which offers Protection against Short Circuit, Over- Voltage & Over- Current, with in-built surge protection. Lens made of PC offers asymmetric light distribution. Estimated LED Lifetime is 70,000 hours minimum. LM80 report from LED Manufacturer should be submitted. Minimum Light fixture Lumen output is 400Lumens. LM 79 Report should be submitted from UL/NABL Authorised Laboratory. Sample Should be submitted for concerned engineer incharge for approval of light fixture.

Supply, Installation, assembling, connection, testing & commissioning of Neon Flex - 5W Per Mtr in Monochrome Colour - IP68 suitable for 220 volt direct power supply with driver, cable & junction box . LM80 report from LED Manufacturer should be submitted and LM 79 Report should be submitted from UL/NABL Authorised Laboratory.

Supply, Installation, assembling, connection, testing & commissioning of Projector Light -LED 9W,LED,3000k Electronic Driver which offers Protection against Short Circuit, Over- Voltage & Over- Current, IP 65 protection,CRI > 70,suitable for 220 volt direct power supply with driver, cable & junction box. Body-Die-casting AL with Surface Anti-ageing electrostatic spray processing & screen. ,Dimension-140mm(Dia.)x196mm(H),without fixing bracket Weight-0.75kgs. Estimated Lifetime-L70 @ 50,000hours minimum. LM80 report from LED Manufacturer should be submitted and LM 79 Report should be submitted from UL/NABL Authorised Laboratory.