SPECIAL REPAIR TO CERTAIN MES QUARTERS AND SINGLE LIVING AT AF STN SURYALANKA

Amount

Taking down cement or cement lime plaster, any description, on brick or stone walls including racking out joints hacking for key scrubbing down with water etc. complete all as specified and as directed.

Demolition of Brick or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars etc., but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position including reinforcement cut as required to facilitate demolition complete all as specified and as directed.

Demolition of cement concrete in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), and aprons removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Taking down chowkats or frames (without taking off shutters from the frame) not exceeding 1.5 sqm each and removing to store complete all as specified and as directed.

Taking down chowkats or frames (without taking off shutters from the frame) exceeding 1.5 sqm but not exceeding 4 Sqm each and removing to store complete all as specified and as directed.

Demolition of Plain cement concrete of any description and in any position not otherwise specifically provided complete all as specified and as directed.

Dismantling Asbestos cement (corrugated, semi corrugated, etc) sheets in roof covering in window sunshades etc, complete all as specified and as directed.

M&L for rendering 5mm thick on fair faces of concrete surfaces in cement mortar 1:3 in ceiling surface finished even and smooth with out using extra cement complete all as specified and as directed.

M&L for rendering 10mm thick on fair faces of brick or concrete surfaces in CM 1:6 finishing even and smooth with out using extra cement complete all as specified and as directed..

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in two layers, first layer 10 mm thick in CM 1:6 and second layer 5 mm thick in CM 1:4 finishing fair and even mixed with WPC as per manufacturer's instructions complete all as specified and as directed. (Note : Supply of water proofing compound shall be measured and paid separately).

Supply only of integral water proofing compound of approved make complete all as specified and as directed.

Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1: 4 complete all as specified and as directed.

M&L for precast reinforced cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in cover slabs,(Manholes etc) chullah hoods, chajjas, water troughs etc and similar articles with plain faces set in cement mortar 1:6 complete all as specified and as directed.

M&L for Mild Steel TMT bars 8 mm dia cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with MS wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

M&L for plain cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate 75mm thick as in sub base complete all as specified and as directed.

M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggregates as in foundation and sides of Gully trap portion complete all as specified and as directed.

M&L for 25 mm thick cement concrete 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in flooring below floor tiles etc. complete all as specified and as directed.

M&L for Non Skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in cement mortar mortar 1:6 complete all as specified and as directed.

M&L for joint free non Skid ceramic coloured tiles (matt finish) 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in cement mortar mortar 1:6 complete all as specified and as directed.

M&L for 100 mm high skirting with joint free non Skid ceramic coloured tiles (matt finish) 7 to 8 mm thick high area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tile, laid over and including 10 mm thick backing coat in cement mortar mortar 1:4 complete all as specified and as directed.

M&L for Glazed ceramic coloured tiles 300 x 200 size 7 mm thick in vertical surfaces as in dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 10mm thick backing coat in cement mortar in cement mortar 1:4 complete all as specified and as directed.

M&L for 18-20 mm thick Granite stone slabs of any type machine cut bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing laid over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

M&L for 18-20 mm thick Granite stone slabs of any type machine cut fixed as in shelves with cement slurry complete all as specified and as directed.

M&L for 20-25 mm thick Kota stone slabs in floorings laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and laid over and including 20 mm thick cement screed bed in cement mortar 1:6, complete all as specified and as directed.

M&L for 20-25 mm thick Kota stone slab as in risers of steps, skirting, dado and pillar laid over and including 10 mm thick backing coat in cement mortar 1:4, and jointed grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for rounding to the edges of stone slabs one edge as in steps, cooking platform, and other similar situations complete all as specified and as directed.

M&L for Chequered cement concrete tiles 30 cm x 30 cm x 25 mm thick with grey cement and pigments, set, jointed and pointed in neat cement slurry in floors/ pavings etc laid over and including 20 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for 75 mm thick plain cement concrete 1:3:6, type C-1, using 20mm graded stone aggregate as in plinth protection, paving etc. surface finished even and smooth without using extra cement complete all as specified and directed.

S&F for Pressed steel frames 125 x 60mm size for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, supplied and fixed complete all as specified and directed.

S&F for Pressed steel frames 105 x 60mm size for doors with one or more rebate including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed.

S&F for Pressed steel frames 75 x 50 mm size for cup boards with one rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed.

M&L for Plain cement concrete 1:3:6 type C-0 using 12.5 mm graded stone aggregate for filling of hollow portions of door frames etc., complete all as specified and directed.

S&F for 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F for 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F for 35 mm thick second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc.( with out sash bars), edges of framing plain, chamfered with plain chamfered or rounded, mitred and rebated , edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, wire gauge etc. ; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) fitted to chowkats complete all as specified and directed.

M&L for 18/19mm thick Block board, Grade 2 quality, interior Grade, commercial type, with decorative face veneer on both faces, fixed with screws etc fixed in repairs in shelves of cup boards etc., complete all as specified and directed.

M&L for anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleats for fixing etc., complete all as specified and directed.

S&F for Anodised aluminium window and ventilator glazed /Gauged shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1No) each shutter, hinges type B-21 100mm long (2Nos), suitable handle (1No), complete all as specified and directed.

S & F for Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or wooden/aluminium beeds complete all as specified and directed.

S&F for 4 mm thick Sheet Glass, ordinary quality and glazing in square exc 0.50sqm in each pane fixed in aluminium windows complete all as specified and directed.

S&F for 4 mm thick Figured glass, pin head type and glazing in square n.exc 0.50sqm in each pane fixed in aluminium ventilators complete all as specified and directed.

S&F 200 mm long Aluminium anodised barrel tower bolts of extruded aluminium section complete all as specified and directed.

S&F for 150 mm long Aluminium anodised barrel tower bolts of extruded aluminium section complete all as specified and directed.

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F for 150 mm long Aluminium alloy handles cast type anodised complete all as specified and directed.

S&F for 100 mm long Aluminium alloy handles cast type anodised complete all as specified and directed.

S&F for 100 mm long Aluminium butt hinges extruded aluminium alloy with galvanised steel wire pin anodised, type C-22 complete all as specified and directed.

S&F for 75 mm size Hasp and Staple aluminium anodised safety type with pin hinge including bolt to hinge plate and fixed with screws fixed in repairs complete all as specified and directed.

S&F for 300 mm long aluminium alloy anodised sliding door bolts with hasp and staple (bolt type) and fixing clip of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F of Mild steel 300 mm ,ordinary rat & tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F for curtain rods (drapery rods) not less than 25 mm dia, anodised aluminium alloy with fixing brackets , rollers etc fixed in repairs complete all as specified and directed.

S&F for factory made PVC Solid Door frame of size 50mmx47mm made out of 5mm plain coloured PVC sheet reinforced with MS Square tube, supplying & fixing in opening as per specification and drawings complete all as specified and directed.

S&F of Factory made Solid panel PVC Door Shutter of 30mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beeding and jointed together with solvent cement as per specification and drawing complete all as specified and directed.

M & L for 6mm thick asbestos cement, corrugated or semi-corrugated sheets in roofs, walls etc Fixed with L-type or screws J-type or hook bolts. complete all as specified and directed and as per manufacturer's instructions.

S&F for vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap, and to flushing pipe, anti-syphonage pipe, etc., fixed in repairs complete including making good to floor complete all as specified and directed.

S&F for 10 lit capacity PVC valve less, symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, fixed in repairs complete all as specified and directed.

S&F in repairs Vitreous China wash basin, white, flat back, of size 550x400 mm including brackets, cutting for and pinning in ends of brackets or erecting stand and but exclusive tap, waste fitting and waste pipe etc complete all as specified and directed.

S&F in repairs CP Pillar taps fancy type 15 mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe, complete all as specified and directed.

S&F in repairs of 25 mm bore Gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repairs of Stop valves 15 mm bore, any type Chromium plated cast copper alloy screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

All as per item No. 62 above but fancy type, chromium plated with long shank and cup (Concealed type) complete all as specified and directed.

S&F in repairs 15 mm bore Bib taps, chromium plated, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe, brass ferrule and fixed complete all as specified and directed.

S&F for PVC connections 15mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F in repairs brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete complete all as specified and directed.

S&F for 20 mm outer dia 3 layer PP-R poly-propylene random copolymer concealed pipes SDR 7.4 (PN-16) UV stabilized and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc., including taking up or down steel tubing and connections complete all as specified and directed.

S&F for 25 mm outer dia 3 layer PP-R poly-propylene random copolymer concealed pipes SDR 7.4 (PN-16) UV stabilized and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc., including taking up or down steel tubing and connections complete all as specified and directed.

S&F in repairs of Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes including beding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mmx 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

S&F Stainless steel plate rack 1 mm thick of size 760x930x200 mm of standard makes complete all as specified and directed.

M&L for Preparing new or previously un treated surfaces of wood and wood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for preparing new or previously untreated surfaces of steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of exterior weather coat paint over a coat of primer of surfaces complete all as specified and directed.

M&L for preparing surfaces plastered or unplastered old surfaces of walls and applying one coats of exterior weather coat paint complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed.

M&L for preparing surfaces plastered or unplastered old ceiling surfaces and applying one coats of white wash complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M&L for preparing of old surfaces plastered or unplastered surfaces of walls and applying one coats of white wash complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and directed.

M&L for preparation of old painted surfaces of walls and applying one coat of oil bound distemper complete all as specified and directed.

S&F for 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls or laid in floors as in soil, waste and vent pipes including dismantling of old pipes complete all as specified and directed.

S&F for 110 mm bore PVC (SWR) bends any radius provided with access door, fixed in repairs complete all as specified and directed.

S&F for 110 mm bore PVC (SWR) junction, single (Single T) equal or unequal provided with access door, fixed in repairs complete all as specified and directed.

S&F for 110 mm bore PVC (SWR) Vent cowl fixed in repairs complete all as specified and directed.

S&F for 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls or laid in floors as in soil, waste and pipes including dismantling of old pipes complete all as specified and directed.

S&F for 75 mm bore PVC (SWR) bends any radius provided with access door, fixed in repairs complete all as specified and directed.

S&F for 75 mm bore PVC (SWR) Vent cowl fixed in repairs complete all as specified and directed.

M&L for diameter of outlet in 75mm PVC (SWR) floor trap mm dia plain with grating including jointing with solvent cement , fixed in repairs complete all as specified and directed.

Taking down and removing of existing water proofing treatment of any description completely, taking down of old cement plaster if any or roughening of surfaces and cleaning the top surface of RCC slab with using wire brushes and water to remove all dust and loose particles etc complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:3 on roof/ concrete surfaces with using water proofing compound as per manufacturer's instructions, surface finished even and smooth without using extra cement complete all as specified and directed. (Supply only of water proofing compound/admixture shall be measured and paid separately).

Supply only of liquid waterproofing compound of approved make complete all as specified and directed.

M&L for water proofing treatment with 4mm thick APP modified membrane weighing not less than 4Kg/Sqm reinforced with non woven polyester matt weighing not less than 160 Gram/Sqm having softening point not less than 140 degree Celsius, longitudinal tensile strength not less than 300 N/Sqm, tearing strength of 180 N, laid after applying a coat of Bitumen Emulsion, Primer @ 0.20Kg/Sqm over the thoroughly cleaned surfaces to be water proofed. Membrane shall then be laid with 10Cm side overlaps and 15Cm end laps completely thermos fused by flame torch application as per manufacturer's instructions. Care shall be taken to avoid wrinkles while sticking the membrane on the bitumen surface. A coat of hot blown bitumen 90/15 shall be applied on top of the membrane @ 1.20 Kg/Sqm and finally finished with solar reflective aluminium paint @ 0.10 Kg/Sqm. The water proofing membrane shall be extended up to a height of minimum 30 cm on wall and inserted by cutting groove and filling with bitumen complete all as specified and directed.

Dismantling of water tanks of capacity exc 250 & n.exc500ltrs and removing to store complete all as specified and directed.

S&F for rotational moulded polyethylene water storage tanks IS : 12701 - 1996 marked (cylindrical vertical with headed top) of 500 Litres capacity hoisted and fixed in position all as specified in SSR Part-I complete all as specified and directed.

S&F in repairs 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed. (Minimum weight 455gms) complete all as specified and directed.

S&F in repairs 32mm dia PVC waste pipe for wash hand basins complete all as specified and directed.

S&F in repairs 40mm dia PVC waste pipe for Kitchen sinks complete all as specified and directed.

S&F in repairs 32mm dia Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc with long screwed shanks and fly nuts, flanged end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F in repairs 40mm dia Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc with long screwed shanks and fly nuts, flanged end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F in repairs Brass chromium plated shore roses 125mm size with or without swivel joints, including fixing to steel pipe or union complete all as specified and directed.

S&F in repairs 125X100mm size Salt glazed stoneware gully traps, square or rounded mouthed type 'P' complete all as specified and directed.

M&L for Chipping of slab/columns/beams/chajjas/ parapet and removing loose mortar with chisel hammer without much impact concrete and cleaning the exposed reinforcement with wire brush and sand blasting the surface using river sand with minimum of 6 Kg pressure at the nozzle end by mechanical compressor and providing zinc rich primer at the rate of 5 Sqm/Litre with Shal prime zn R to reinforcement as per manufacturers instructions and including all scaffolding, machinery, tools tackles and men materials and clearing of debris complete all as specified and directed. Make : Shal prime zn R of STP or equivalent brand in Fosroc/Dr. Fixit.

M&L for providing weld mesh size 100 x 100 x 3mm weld mesh and the mesh with shear connectors with 8mm dia reinforcement by drilling 75mm deep anchoring holes and filled with epoxy resign 20gm/hole with Shal grout Anchor as per manufacturers instruction including all necessary scaffolding, machinery, tools tackles and men materials complete all as specified and directed. Make : Shal grout Anchor of STP or equivalent brand in Fosroc/Dr. Fixit.

M&L for providing drilling of 10m dia and 100mm deep holes in existing columns/ beams/slabs and providing 8mm dia reinforcement to the slab @ 300mm c/c and shear connectors anchoring with epoxy resign 50gm/hole with Shaligrout Anchor as per manufacturers instruction including all necessary scaffolding, machinery, tools tackles and men materials complete all as specified and directed. Make : Shaligrout Anchor of STP or equivalent brand in Fosroc/Dr. Fixit.

M&L for providing CM 1:3 by gunniting with gunniting compressor hopper in 2 layers of 50mm thickness mixed with poly propelling fibres and silica fumes @ 0.5 Kgs per bags of cement including all necessary scaffolding, machinery tools tackles, men materials and finishing the surfaces even and smooth, without using extra cement plumb and making surface true to geometry in line complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting, bulbs etc. removing materials to store for taking credit and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

M&L for point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits) with 1.5 sqmm nominal cross-sectional area, single core PVC insulated (FRLS), unsheathed multistranded copper conductor cable 1100 Volts grade drawn through and including rigid non-metallic PVC concealed conduit 25mm dia medium grade and accessories ISI marked and including chases Cutting and making good surfaces, suitable modular pressed steel terminal boxes 1.6mm thick (recessed) with modular cover plates for fixing of switches, sockets etc including 1.5 Sqmm nominal cross sectional area, single core PVC insulated (FRLS), unsheathed multistranded copper conductor cable earth continuity wire to common earth and connected to earth dolly for one light / fan/ Security light/ 5Amps Indp Socket / Bell point controlled by one switch complete all as specified and directed.

All as per Item No. 108 above but One 3 pin socket outlet 5 amps on same board controlled by one switch with 1.5 sqmm size cable.

All as per Item No. 108 above but one 3 pin socket outlet, 15 amps / AC Metal Clad, controlled by one switch on independent board with 4 sqmm size cable for Phase, neutral and earth.

S&F in repairs Modular Switch 5/6 Amps, 1module 1 Way complete all as specified and as directed.

S&F in repairs Modular Switch 15/16 Amps, 1 Module 1 Way complete all as specified and as directed.

S&F in repair Modular Bell Push 1 Module, 1 Way complete all as specified and as directed.

S&F in repair Modular Socket 5/6 Amps, 2 Module 2 and 3 pin complete all as specified and as directed.

S&F in repair Modular Socket 15/16 Amps, 2 Module 2/3 pin complete all as specified and as directed.

S&F in repair Modular Fan Regulator Step type, 2 Module 120W complete all as specified and as directed.

S&F in repair Bell Ding Dong, 230 Volts Complete all as specified and as directed.

S&F in repair 3 Module Cover Plate with frame and Metal Flush Box complete all as specified and as directed.

S&F in repairs 8 Module Cover Plate with frame and Metal Flush complete all as specified and as directed.

S&F in repair Ceiling rose, 3 plate /PVC/ polycarbonate, isolated body complete all as specified and as directed

S&F in repair LED lights fitting 1x 20W, 4 Feet 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F in repair LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F in repair LED Bldg. Security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

S&F in repairs street light brackets made of 25 mm dia G.I. Pipe light grade in shape and angle as directed not exceeding 1.5 mtrs in length fixed to wall with suitable size of M.S. flat iron clamps, M.S nut & bolt with cup washers, painting to MS material with anti corrosive paint complete all as specified and as directed.

Taking down carefully ceiling fan complete of any size and capacity, Painting of ceiling fans complete, with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc and refixing the same complete all as directed and as specified.

Taking down carefully exhaust fan with louver complete of any size and capacity, Painting of fans complete, with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc and refixing the same fan with new louver complete all as directed and as specified.

S&F in repairs Single pole and neutral AC Metal enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps, C Curve complete all as specified and as directed.

S&F SPN DB Double door 8 way with tray for provision of MCBs, and Dolly for earth and neutral complete all as specified and as directed.

S&F MCB Two Pole 6-32 Amps, 10 kA, C Curve complete all as specified and as directed.

S&F MCB Single Pole 6-32 Amps, 10 kA, C Curve complete all as specified and as directed.

M&L Earthing complete with earth galvanized steel plate electrode 600x600x6mm buried directly in ground earth pit not less than 2.25 mtr below ground level with top edge of the plate not less than 1.5 mtr below ground level, surrounded from all sides with mixture of charcoal and common salt and electrode connected with galvanized earth lead GI wire 4 mm dia by means of bolts, check nut and washers of GI or steel, GI pipe light grade of 15 mm bore as protection pipe, GI wire of length not more than 7.5 mtr and connected to test point. GI pipe 20mm dia light grade for watering, funnel with wire mesh, PCC pit and RCC (1:2:4) type B-1 for cover with 8 mm dia bar reinforcement both ways @ 140 c/c including excavation and earth work disposal of surplus soil to a distance not exceeding 50 mtr as shown on electrical plate No 3 of SSR 2009 complete all as specified and as directed.

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of 2.0 core 10 Sqmm complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for laying of cable/ pipe line n exc 10 sq. m on plan and n exc 1.5 m in depth and getting out soft / loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed.

S&L Sand filling for cable protection above and below cable and rammed down complete all as specified and as directed

S&L Red Bricks common burnt clay building bricks, sub-class ‘B’ designation 75 complete all as specified and as directed.

S&L GI pipe light grade for cable protection with clamps of size not less than 40 mm dia complete all as specified and as directed.

Supply and lay in repairs 3 layer ( inner antimicrobial, outer UV stabilized) ISI marked,IS-15801, PP-R pipes SDR 7.4 (PN-16) and PP-R plain plain and brass threaded fittings laid in concealed work complete of size outer dia 32 mm complete all as specified and as directed.

Supply and fix PPR Gate Valves (Brass Insert) of outer dia 32 mm complete all as specified and as directed.

Cutting DI/ERW/ GI/ UPVC / PPR pipe of any bore up to 80 mm dia and reducing to required length before laying and insertion of 'T's and branches for 50 mm/ 25 mm bore dia complete all as specified and as directed.

MAHIRA ENGINEERING & INFRASTRUCTURE

DHANA CONSTRUCTIONS

Ruchira Associates