VIJAYAWADA Division :- 1. S&T works in connection with TTRR(TWS+WCMSC) 1 in 8.5- 5 Sets , TTR (FS+TWS+WCMSC) 1 in 12 -13 Sets, TTTR (TWS+WCMSC) 1 in 12 -145 Sets & TTR (FS+TWS+WCMSC) 1 in 16 - 5 sets at various locations in DEN/East/BZA section. 2. S&T works in connection with TTRR(TWS+WCMSC) 1 in 8.5- 5 Sets , TTR (FS+TWS) 1 in 12 -2 Sets, TTR (FS+TWS+WCMSC) 1 in 12 -9 Sets, TTRR (TWS + WCMSC) 1 in 12-42 sets & TTR (FS+TWS+WCMSC) 1 in 16 - 4 sets at various locations in Sr DEN/South/BZA section. 3. S&T works in connection with TTR(FS+TWS) 1 in 8.5- 2 Sets , TTR (FS+TWS) 1 in 12 -6 Sets, TTR (FS+TWS+WCMSC) 1 in 8.5 -5 Sets, TRR (FS+TWS + WCMSC) 1 in 12-23 sets , TTR (FS+TWS+WCMSC) 1 in 16 - 1 set, TTR (CS+CMSC) 1 in 8.5 - 3 Sets and TTR (DS) - 10 Sets at various locations in Sr DEN/North/BZA section.

A-SUPPLY PORTION (SOR)

Supply of Surface Base 140mm dia. CLS post as per DRG.No. S 2011/M (INSPECTION BY CONSIGNEE)

Supply of Offset Bracket to suit 140mm dia CLS post with two numbers of U bolts and nuts complete (INSPECTION BY CONSIGNEE)

Supply of Calling On Signal Unit complete with U Bolts as per RDSO DRG. No. SA.24351 (Adv.) or latest. (INSPECTION BY CONSIGNEE)

Supply of Ground type position light shunt signal complete with base, pipe, arrow mark and hoods as per RDSO DRG. No. SA 23840 or latest. (INSPECTION BY CONSIGNEE)

Supply of Junction type / Direction type route indicator as per specification IRS:S 66-84 Amd. 1 or latest. c) Three way as per DRG. No. SA 23403 (INSPECTION BY CONSIGNEE)

Supply of Insulations for Ground Connections for point machine comprising of the following: 1)Switch extension piece insulation -1set (Each set comprising of S3265 -1 no; S 3266-1No; S23199-2No and S8640-4No.) 2)Stretcher bar insulation-3sets (Each set consisting of T10367-1No., 12 T10368-2No., T10371-4No.) 3)Gauge tie plate insulations-4sets (Each set consisting of T 10372- 1 No, T10368 -3 No and T10371-6 No.) 4)Drive lug insulation-1set (Each set consisting of S 8804 - 1 No., S 8813 -2No.and S 8640-4No.) complete with bushes. Note- The type of insulation required will be specified by engineer in-charge of the work depending on the type of machine proposed (Universal /PTJ Make) as per specification. (INSPECTION BY CONSIGNEE)

Supply of Track feed battery charger to work on 110V AC for charging1or 2 or 3 or 4 lead acid cell of 80AH (10Amps) used in track circuit as per RDSO Specn. No. IRS.S.89/2013 Ver 1.0 latest (INSPECTION BY RDSO)

Supply of Track lead junction boxes fibre glass as per DRG.No.CWM-00597 of F.R.P 14 material to and specification IRS:S 23 along with fixtures i.e., one MS angle 50mmx50mmx5mm, 0.9m long, two numbers of G.I pipes of 25 mm dia, 500 mm long along with nuts and bolts and 500 mm long (grommet bushes, 60 mm ARA terminals-2 No's) (INSPECTION BY CONSIGNEE)

Supply of B type chokes to as per specification IRS: S65- 83 Amd.1 or latest. (INSPECTION BY RDSO)

Supply of titanium coated 7.2mm drill bits of Bosch/Addision make. (INSPECTION BY CONSIGNEE)

Supply of 24 V DC plug-in type miniature tractive armature, AC immune relay 18 complete with plug board, retaining clip/ATC Clip and connectors as per IRS: S 23-88 Amd.1 or latest, IRS: S 34-68 Amd. 6 or latest, IRS: S 60-78 Amd.1or latest, IRS: S 67-85 Amd. 3 or latest (as applicable). a)QBCA1- 2HF/4B, Interlocking code: BCEJK as per specifications BRS 943 or Latest (INSPECTION BY RDSO)

"Supply of 24 V DC plug-in type miniature tractive armature, AC immune relay 19 complete with plug board, retaining clip/ATC Clip and connectors as per IRS: S 23-88 Amd.1 or latest, IRS: S 34-68 Amd. 6 or latest, IRS: S 60-78 Amd.1or latest, IRS: S 67-85 Amd. 3 or latest (as applicable). b)QNA1- 8F/8B, Interlocking Code: ABDGH as per Spec BRS 931 A or Latest (INSPECTION BY RDSO) "

Supply of Lugs and Eyelets: b)Copper lugs 10 Sq.mm of reputed make. (INSPECTION BY CONSIGNEE).

Supply of 6 digit 24V non resettable impulse counter. (INSPECTION BY CONSIGNEE)

"Supply of Various Tools for S&T installation. c)Supply of Clip On Meter of Model Fluke 317 or similar with the following specification. 1. True RMS responding. 2. Voltage - DC 600V, AC 600V, DC accuracy - ±1% + 4 digit. 3. AC accuracy - ±1.5% + 5 digit 4. Current - DC 600A, AC 600A, AC 45 accuracy: - ±1.5% + 5 counts, AC / DC current measurement. 5. Unique 40A low frequency measurements capability with 0.01A resolution 6. Special filter circuit to enable accurate measurement of PWM output. 7. Additional measurement of resistance 8. Continuity check feature 9. Data hold features with large, easy to read backlight display. 10. Calibration certificate 11. 1 year warranty (INSPECTION BY CONSIGNEE)" Above/

B-LABOUR PORTION (SOR)

Track crossing/ Road Crossing by Horizontal Boring method at culverts /track / pucca road as per SCR Drg. No. 5770. This also includes insertion of HDPE pipe of 110 mm/G.I Pipe of 100 mm in the bore drilled (HDPE pipe/ GI pipe is to be supplied by Railway).

Cable laying and meggering. a)laying different type of cables in the trench. Termination covered elsewhere.

Supply and Filling sand in trench/under floors/OFC chambers, complete as per instruction of engineer in charge.

Supply & Laying of G.I Pipes with medium and threaded collar & coupler, quality to specification IS.1239 (part-I) 1990 and galvanised to specification IS.4736-1986. b) G.I Pipes of 100mm diameter (INSPECTION:RITES)

Supply, transporting and installation of Concrete (RCC) Route Indicators at intervals of 50 meters as per instructions of engineer in charge as per drawing no. SK 12/10.They should be of standard RCC with letters "SCR S&T cable" as per type of cable laid to drawing. In case of telecom quad cable joint locations it shall be painted with GREEN and ORANGE colour for normal indication of cable path. (INSPECTION:CONSIGNEE)

Supply & fixing Hard Wood planks of 40mm thick and not less than 200 mm width with smooth surface, and painting with black enamel paint painting (Hardwood, paints, fixingbolts is to be arranged by contractor) Per

Shifting of apparatus case (Half).:Excavation of pit in and around the existing location 21 boxes very carefully without damaging the working cables and shifting and turning the location boxes to clear of the infringement as instructed by the Railway representative at site. The work includes, ensuring the safety of the signalling system, releasing the cable coils to give access for shifting/turning the location boxes. Necessary masonry work and earth work in and around the location boxes to the required level shall be done as instructed by the Railway representative at site. If the existing earth connections to the location boxes are disturbed, the earth wires shall be properly reconnected. [All materials required for the work shall be supplied by the Contractor].

Fabrication, supply and erection of conventional Earth to Signalling/Telecom equipments -Excavation of earth and providing earth pipe of size 50mm dia. 3.5mm thick 2.0 m. long G.I. pipe of heavy quality with masonry tub constructed around at earth locations as specified by site 22 Engineer. Alternate layers of 30kgs-charcoal and 30kgs-common salt to be filled in the pit while closing. The pipe perforation etc., to be carried out as per drawing No. SK 10/10. The earth pipe to be connected to the function with cable as supplied by Railways. The reading should be painted on the masonry tub. The masonry tub of 300 mm x 300 mm x 300mm (along with Kundi) should be covered with cement slab. (INSPECTION:CONSIGNEE)

"Foundation and erection of Colour light signal which includes a) Excavation of pit, casting concrete foundation as per SCR Drg. No. 5772 using metallic templates, for erection of Colour light Signals 4 aspects (foundation bolts, cement, river sand, stone jelly of size 20/20mm dia and all other miscellaneous materials required for the work shall be supplied by the contractor). b) Erection of surface base, signal post, mounting of Colour Light Signal up to 4 aspects complete on signal post / offset bracket, LED fixing, plumbing of the signal through sealing gap between Surface base and signal post, fixing of ladder with platform complete and concreting of ladder shoe, fixing of number 23 plates, marker board, termination tail cables, wiring of signal unit, provision of EWS locks, and painting of one coat of red oxide and two coats of aluminium/enamel paints. When the aspect is fixed on offset bracket using 'U' bolts and nuts, a through bolt shall be provided by drilling of hole in the signal pole to prevent the offset bracket from sliding down. (Supply of surface base, offset bracket, CLS pole, CLS aspects complete , ladder with shoes and platform, LED aspects, current regulators and wire coils will be supplied by Railways). ('U' bolts and nuts, through bolts and nuts, cement, stone jelly 20/25mm dia, river sand, Signal Colour Rings, all fixing bolts and nuts, teak wood, paints PVC/Nylon sleeves, enamelled number plates, enamelled marker boards , EWS locks, and all other miscellaneous materials for the work shall be supplied by the contractor). @40<37@ Payment after completion of workmentioned at (a) and remaining 40 % after completion of work at (b))"

Strengthening of foundations of signals, Full/Half location boxes up to a height of 30 24 cm, by carrying out the earth work around the foundation, ramming of the earth, carry out masonry work from bottom of earth work using country stones and cement masonry to prevent the earth from slipping down the bank.

Fixing of universal point machines and wiring on PSC/Wooden sleepers as per standard 25 drawing. Wiring as per circuitry includes fixing & wiring of point contactor unit frames and controlling relays, fixing and wiring of point termination box, fixing of crank handle ward plate of required configuration and Ground connections, P-clamp insulations, setting, stretcher bars etc., [All miscellaneous material required such as nuts, bolts, washers are to be arranged by contractor] Per Point

Installation, termination of cable in termination box, wiring, testing and commissioning 26 of High Thrust point Machine. This includes fixing of point machine on MS plate fixed on sleepers complete with fixing of anti theft covers, MS termination boxes, ground connections, required insulation, crank handle ward (wherever required) etc. This also include necessary adjustment and smithy work, drilling of holes on tongue rails, supply of all miscellaneous material such as flat, angle, bolt, nuts, pins etc.

Fixing of Track lead junction box on angles (50 x 50 x 6 mm size), drilling one hole on either side of the box of suitable size and fixing track lead junction box by the side of the track, drilling 27 4 holes of 7.2 mm dia. on Rail, connecting double track leads with bond pins, running track lead wire, termination of track lead wire on ARA terminals duly fixing the same inside the TLJB Teak wood board bolted inside the track lead junction box. (Fixing angles, bolts, nuts and teak wood boards to be supplied by the contractor).

Wiring of Track circuits feed end, relay end complete with TLDs, batteries, chargers , Chokes, track relays, double lead wires, providing insulation etc,. Connected with track commissioning 28 of track circuit including provision of bracket for TLD covers and painting. Anti-tilting arrangement has to be done for chargers & batteries. All miscellaneous material required for installation shall be supplied by contractor.

Painting of particulars of Glued Joint on rails/track circuit no. on TLJ boxes as per particulars issued by Engineer in charge. Before painting on surface of the Glued Joint Rails/TLJ boxes 29 shall be cleaned thoroughly. Painting shall be done with approved quality of standard paints like Asian/Johnson/ Nicholas /Berger etc. All the men and materials shall be arranged by the contractor and the colours scheme shall be as per the instructions of Engineer in charge. PER UNIT = PER RAIL JOINT

Drilling of four no's of 7.2mm holes, per rail joint on web of the rail , providing bond wires with wire rope. (Bond pins single groves are to be supplied by contractor - Wire rope for bonding will be supplied by Railways).Per Unit = Per Rail Joint

Fabrication, Supply and fixing of CALLING ON instruction boards, STOP boards/ 31 BSLB/Shunting Limit Board/Auto section board or any other board with engineering grade reflective sticker of size 600X1000 mm GI sheet, with MS angle of 75X75X6 mm with 6 meter length including paint, excavation of pit and concrete foundation etc. as per the instructions of sight in-charge. All necessary materials to be arranged by the contractor) (INSPECTION BY CONSIGNEE)

Fixing of the following on Pre-erected Relay Racks. e)Fixing relay bases on the relay frames erected in Relay Room, Wiring of all types of relays by drawing various sizes of wires/multi core cable, fixing fuses, condensers, resistances, LEDs etc and wiring duly soldering the same as per approved circuit diagram, testing point to point before soldering and after soldering, bunching and lacing as per detailed technical specification. Numbered ferrules shall be provided for each wire. Different colour codes and sizes of wire to be used as per standard practice. This also includes , 35 provision of all PVC sleeves required to be provided. Copper lugs to suit to 16/02 wire and neat bunching, lacing with Modi Nylon / Twine thread and using PVC dotted tape with buttons. This also includes solderingall the wires in the relay room with Rosin core of IS Spec.1921 @40<37@ Tin and 40% Led). Soldering should be done as per standard practice. This also includes inserting the clips, point to point testing as per the circuit diagram and plugging relays to Relay bases (except Inter- cables, relays other materials such as Rosin core, flux, nylon thread. PVC dotted tape should be supplied by the contractor). Point to point testing should be done in the presence of Engineer-in- charge as instructed in two stages, one before soldering and the other after soldering.

Supply and Fixing of stop board of size (600mm dia) made out of 1mm thick GI sheet with high intensive prismatic retro reflective sheet, red background and white colour letters in three 36 languages English, Hindi and local language in as per railway standards with minimum reflectivity distance of 250m with all necessary fixing clamps, bolts and nuts to suit for electric lifting barrier as per enclosed DRG. No. S&T/MFT/6077 or latest. The local language shall be as per the instructions of site in-charge. (INSPECTION BY CONSIGNEE)

Supply and fixing of 'AHUJA' or similar make horn type loud speaker 15W 8 ohms impedance at LC gate Road signal. (INSPECTION BY CONSIGNEE)

Supply and fixing of Electronic Hooter unit 24/110 DC of approved design/make able to drive 2 No. of Speakers of 8 ohms 15W. (INSPECTION CONSIGNEE)

Supply of commercial grade operator VDU of size 55" Full HD, with backlit LED, with HDMI/DVI port, Inbuilt Speaker, required HDMI/DVI cables for connectivity and other miscellaneous item required for installation. (INSPECTION BY CONSIGNEE)

Supply of fan less embedded industrial grade computers (Similar to Moxa V2406A or 40 better ) with all accessories such as key board, mouse, antivirus etc. of industrial grade as per approved Specification as recommended by RDSO (TAN No. STS /TAN /3007 Version 1.0 or latest) (INSPECTION BT CONSIGNEE)

"Releasing of the following equipments without causing damage, stacking neatly at a centralised place near the site of work as shown by the in charge, and handing over the same to the 42 Stores depot as per the inventory made. n) Dismantling and releasing of existing Point machines (all types) including ground connections and other accessories available complete without any damage to the gadgets, accounting and stacking them neatly at a place as instructed by Railway representative at site."

Supply and installation of 48 volts 200 AH maintenance free VRLA battery in charged condition as per RDSO specification IRS:S-93/96(B) (Amd. 1 ) or latest. (2 volts 200 AH - 24 Nos. each set). (INSPECTION BY RDSO) Above/

A1-SUPPLY PORTION (NS)

B1-LABOUR PORTION (NS)

Item Breakup - A1-SUPPLY PORTION (NS)

A) Supply of DC-DC Converters for EI Internal Numbers 10.00 Power Supply (Inspection by Consignee)

B) Supply of Optical converter card, SPHC-PA- Numbers NIVOX for KYSON Electronic Interlocking (Inspection Consignee) Total 3266958.00