PROVN OF CERTAIN EM AND BR WORKS SERVICES FOR B C FLT, TRG CUM BRIEFING ROOM FOR AGNIVEERS AND SOLAR SECURITY LIGHTS AT AF STATION BHUJ

Amount

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm watering, and removing surplus soil to a distance n exc 50 m and making good surface in soft/loose soil complete all as specified and directed by Engr-in-Charge.

Material & labour for providing cement concrete 1:2:4,type B2 (using 40mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and as directed by Engineer-in-Charge.

Supply & fix steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and as directed by Engineer-in-Charge.

Supply & fix rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and directed by Engineer-in-Charge.

Supply & fix rolled sections Fe 410 -W (GdeE- 250) quality A as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc complete all as specified and directed by Engineer-in-Charge.

Supply & fix plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and directed by Engineer-in-Charge.

Supply & fix mild steel wind ties of size 25mmx5mm for roof including securing bolts including cuting tops to shape as directed, drilling holes and similar works confirming to Fe-290 Gde E-165 complete all as specified and directed by Engineer-in-Charge

Supply & fix pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall and make good to prevent leakage, fixed with self tapping screws complete all as specified and as directed by Engineer-in-Charge.

Material & labour for preparation of new steel or iron surfaces of any description, not otherwise described, over 10 cm in width or girth and applying two coats of synthetic enamel paint (first quality) over one coat of red oxide primer complete all as specified and directed by Engineer-in-Charge

Material & labour for preparation of new steel or iron surfaces of any description, not otherwise described, n. exc. 10 cm in width or girth and applying two coats of synthetic enamel paint (first quality) over one coat of red oxide primer complete all as specified and directed by Engineer-in-Charge

Surface excavation n. exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed by Engineer-in-Charge.

Removing excavated soil to a distance n.exc. 50 mtr and depositing where directed at a level n.exc. 1.5m above the starting points complete all specified and directed.

Material & labour for hard core of gauge n.exc 63 mm deposited, spread and levelled in layers n.exc 15 cm thick with broken stone/boulders, watered and rammed to a true surface complete all as specified and directed by Engr-in-Charge.

Material & labour for 100 mm thick for plain cement concrete 1:4:8,type D2 (using 40mm graded stone aggregate) as in sub base to floor etc complete all as specified and as directed by Engineer-in-Charge.

Material & labour for PCC 1:2:4 type B2 100 mm thick by using 20 mm graded curshed stone aggregate as in floor finishes complete all as specified including necessary formwork complete all as specified and as directed by Engineer-in-Charge.

Material & labour for Precast cement concrete block masonry with solid blocks exc 10cm in width Type (1:3:6) (using 20mm graded stone aggregates) and setting in cement mortar 1:6 complete all as specified and as directed by Engineer-in-Charge.

Material & labour for 10 mm thick rendering on concrete surface or PCC block masonry in CM 1:3 by mixing integral water proofing compound, including finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.. Note : supply only WPC will be measured separately.

Supply only water proofing compound confirming to IS complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparation of new plastered surface and applying three coat of white wash on wall complete all as specified and directed by Engineer-in-Charge. .

Material & labour for preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of wall primer complete all as specified and as directed by Engineer-in-Charge.

Supply & fix solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening complete all as specified and directed by Engineer-in-Charge.

Supply & fix factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site complete all as specified and directed by Engineer-in-Charge

Supply & fix aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed by Engineer-in-Charge

Supply & fix aluminum anodized barrel tower bolt of extruded section , length of bolt 150mm complete all as specified and as directed by Engineer-in-Charge.

Supply & fix aluminum handle cast type anodized 150 mm complete all as specified and directed by Engineer-in-Charge.

Supply & fix SM butt hinges medium weight cold rolled 100 mm size complete all as specified and directed by Engr-in-Charge.

Supply & fix vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and as directed by Engineer-in-Charge.

Supply & fix 10 litres, cast iron, valveless. syphonic action type, flushing cistern, high level, with inlet, ball valve, float, chain and pull, and bracket complete all as specified and as directed by Engineer-in-Charge.

Supply & fix seat and cover for pedestal pan complete all as specified and as directed by Engineer-in-Charge.

Supply & fix flush pipes to pedestal pan, including all joints complete all as specified and directed by Engineer-in-charge.

Supply & fix rotational moulded polythene white water storage tank tripple layared (cylindrical , vertical with closed top , ISI marked , ) hoisted and fixed in position all as specd in SSR Part 1 of capacity 500 ltrs also including provision of 20 mm bore ball valves , high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum wt 455 gms) complete all as specified and directed by Engineer-in-charge.

Supply & fix 20mm thick screed bed or bedding layer of cement mortar 1:6 for laying floor finishes complete all as specified and as directed by Engineer-in-Charge.

Material & labour for Non - skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed by Engineer-in-Charge.

Material & labour for 10 mm thick screed in CM 1:4 to receive tiles etc on vertical surface of walls complete all as specified and directed by Engr-in-Charge.

Material & labour for glazed tiles 200mm x 300mm x 7mm thick in as in dados/skirting set and jointed in neat ment slurry and pointed in white or coloured cement to match coloured tiles complete all as specified and as directed by Eng-in-Charge.

Supply & fix PVC connection 15 mm size with PTMT ruts of length 600mm complete all as specified and directed by Engineer-in-Charge. .

Supply & fix health faucet 15 mm size of length 1000mm with holder complete all as specified and directed by Engineer-in-Charge. .

Supply & fix brass chromium plated tubular towel rail 20 mm dia `D’ type 60 cm long between flanges complete all as specified and directed by Engineer-in-Charge.

Supply & fixing CPVC pipes 20mm dia SDR-11 & plain CPVC SDR-11 with all fittings on wall/ceiling or laying in floor/wall complete with proper steel saddling of half meter apart of each complete all as specified and directed by Engineer-in-Charge .

Supply & fix stop valve 20 mm (ISI marked) cast copper alloy screwd down, high pressure with but fancy type, chromium plated with long shank and cup (concealed type) complete all as specified and directed by Engineer-in-Charge. .

Supply & fix 15mm dia Bib taps, cast copper alloy fancy type chromium plated, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engr-in-Charge.

Supply & fix brass ball valve high pressure with polyethylene float and ply nut complete screwed for iron pipe or for brass ferrule and fixed bore of pipe 20 mm size complete all as specified and directed by Engineer-in-Charge. .

Supply & fix PVC (SWR) gulley trap 125/110 mm setting and jointing with solvent cement complete all as specified and directed by Engineer-in-Charge.

Supply & fix vitreous china wash basin white, flat back 580x 450 mm excluding taps, waste, chain plug and porcelain stopper incl bracket complete all as specified and directed by Engineer-in-Charge

Supply & fix 32 mm bore waste fitting, brass chromium plated for glazed ware sink, basin etc with long screwed shanks and fly nuts, flange and bedded in red laid cement and other and fixed complete all as specified and directed by Engineer-in-Charge

Supply & fix 15 mm dia fancy type pillar taps, cast copper alloy with capstan head, chromium plated screwed down high pressure, with or without lettered hot or cold with long screw shank and fly nuts screwed for iron pipe complete all as specified and directed by Engr-in-Charge

Material & labour for PVC (SWR) floor trap 75mm, plain with grating including jointing with solvent cemen complete all as specified and directed by Engr-in-Charge.

Supply & fix 110 mm ;PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by Engr-in-Charge.

Supply & fix 110 mm ;PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls complete all as specified and directed by Engineer-in-Charge. .

Supply & fix soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed by Engineer-in-charge. .

Supply & fix angle stop valve of any colour high pressure screwed for iron pipe and fixed, (Minimum weight 15mm-90gms complete all as specified and directed by Engr-in-Charge. .

Supply and fix galvanised steel punched type concertina coil of 1050mm dia (dia of coil when unstretched with Nos. of circles 50, Nos. of clips 230 with weight 15.60 kg/ coil and recommended and average coverage area is 6 RM/ coil) and fixed to angle iron post/ struts with 3.15mm dia GI wire etc complete all as specified and directed by Engineer-in-Charge. .

Excavation in trenches not exc. 1.5m wide and not exc. 1.5m in depth for foundation etc or for shafts, wells, cesspits, manholes pier holes etc not exc. 10sqm on plan and not exc 1.5m in depth and getting out in hard/dense soil complete all as specified and directed by Engineer-in-Charge.

Material & labour for cement concrete type C2(1:3:6 )using 40 mm graded stone aggregate as in bed (100 mm thick) to drain pipe including packing under and haunching against the sides of pipe size 150 mm bore complete all as specified and directed by Engineer-in-Charge.

Material & labour for reinforced concrete pipes 150mm dia class NP2, laid and jointed complete with collars complete all as specified and directed by Engineer-in-Charge

Material & labour for cement concrete 1:3:6 type C2 (using 40 mm graded curshed stone aggregate) as in foundation filling and mass concrete complete all as specified and directed by Engineer-in-Charge

Material & labour for precast cement concrete (1:2:4) type B1 (using 20 mm graded stone aggregate) as in cover slabs for man holes and set in CM 1:4 incl necessary form work complete all as specified and directed by Engr-in-Charge . ( Note : Reinforcement steel shall be measured and paid separately)

Material & labour for TMT bars 10mm dia and over cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia complete all as specified and directed by Engineer-in-Charge.

Material & labour for soakage well including excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 1.2M dia x 3 M effective depth complete all as specified and directed by Engr-in-Charge and as shown on TD drawing CEAA/TD/80 sheet 1/2 and 2/2 dated 01.12.93 complete all as specified and directed by Engr-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. complete all as specified and directed by Engineer-in-Charge. .

Material and labour for point wiring complete with 1.5 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 volts grade ISI marked drawn through and including PVC CASING & CAPPING INCLUDING accessories etc including fixed to wall/ceiling including provision of 1.5 sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed as earth wire continuity complete all as specified and directed by Engineer-in-Charge for following:-

One light point controlled by one, one way switch single pole piano type .

One Fan/exhaust point controlled by one, one way switch single pole piano type each .

One 3 pin 5/6 Amps socket out let on independent board .

One 3 pin 5/6 Amps socket out let on same board .

All as per item No 62.00 here-in-before but with 2.5 Sqmm Copper conductor cable for one 3 pin, 15/16 Amps socket out let on independent board complete all as specified and directed by Engr-in-Charge. .

Supply and fix PVC rectangular block for mounting, switches, sockets, fan regulator etc. with 3 mm thick plastic laminated sheet cover of size 100 mm x 100 mm and 50 mm deep complete all as specified and directed by Engineer-in-Charge. .

Supply and fix double door sheet metal enclosures factory made DBs protection class IP-43, suitable for fixing of MCBs, Isolators etc, confirming to IS 13032 SPN 8 ways with 200 Amp rated bus bar 415 volts powder coated complete all as specified and directed by Engineer-in-Charge.

Supply & fix double door Sheet metal enclosures factory made DBs protection class IP-43, suitable for fixing of MCBs, Isolators etc, confirming to IS 13032 SPN 4 ways with 200 Amp rated bus bar 415 volts powder coated complete all as specified and directed by Engineer-in-Charge.

Supply & fix isolators/MCBs of the under mentioned type and rating and fixing in DBs (DBs measured and paid for separately) (Note :- Make of the isolator should be the same as that of DB) complete all as specified and directed by Engineer-in-Charge for the following:-

MCB TPN of 415 volts 63 Amps Capacity, 'C' series, 10 KA

MCB SPN of 240 volts 5-20/32/40 Amps Capacity, 'C' series, 10 KA

MCB SP of 240 volts 5-40 Amps Capacity, 'C' series, 10 KA

Supply & fix switch socket combination multi purpose 2 in 1, 5 pin 5 Amps, flush type, ISI marked complete all as specified and directed by Engineer-in-Charge

Supply & fix switch socket combination 2 in 1 , 5/15 Amp, flush type, ISI marked complete all as specified and directed by Engr-in-Charge

Meterial & labour for sub main wiring with two runs of PVC insulated and unsheathed FRLSH cable 650/1100 Volts grade, conforming to IS - 1536-1977 multi-stranded 4.0 sq. mm single core size copper conductor drawn through and including PVC Casing & Capping with accessoriesfixed to wall/ceiling with proper saddles and 1 runs of 4.0 Sqmm single core multistranded copper conductor PVC insulated and unsheathed FRLSH cable 1100 volts grade, ISI marked as earth continuity wire complete all as specified and directed by Engineer-in-Charge. (Note : Two runs of conductor with one runs of earth wire and one run of Caping casing will be measured and paid as one unit) complete all as specified and directed by Engineer-in-Charge.

Supply & fix metal encosure single pole and neutral with a two pin and earth plug and socket complete with one single pole MCB of 20 Amps 'C' series complete all as specified and directed by Engr-in-Charge.

Fixing only AC of capacity 1.5/2.0 Ton including outdoor and indoor on existing wall by making suitable alterations and making connection complete all as specified and directed by Engineer-in-Charge. .

Supply & fixing wall mounted decorative ultra slim LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack instant start with uniform light distribution 10 W 2 ft indoor decorative (white) with 2 Core copper wire from ceiling rose to light fitting complete all as specified and directed by Engineer-in-charge. .

Supply & fixing wall mounted decorative ultra slim LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack instant start with uniform light distribution 20 W 4 ft indoor decorative (white) with 2 Core copper wire from ceiling rose to light fitting complete all as specified and directed by Engineer-in-charge. .

Supply & fix exhaust fan, steel body AC single phase. 230V of size 300m sweep with, blades, and frame and louvers incl necessary cutting in steel and making suitable hole for fixing exhaust fan complete all as specified and directed by Engineer-in-Charge. .

Material & labour for earthing complete with galvanised steel earth plate electrode 60 cm x60 cm x 6 mm thick buried directly in ground ,(Earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level ,connected to and including galvanised iron earth wire 4 mm dia by means of nut, bolts, check nuts and washers of galvanised iron or steel as shown in electrical plate No.3 of SSR Part-I (2009) complete all as specified and directed including testing on completion including the material and labour complete all as specified and directed by Engineer-in-Charge of the following : - (a) Excavation and earth work for drilling hole for electrode in any type of Soil. (b) PCC pit in cement concrete 1:2:4 type B-1, Pre cast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than1.87 Kg/ Sq meter. (c) Funnel with watering pipe of GI 20 mm nominal bore light grade and lugs etc complete all as specified and directed (d) 15 mm nominal bore medium grade GI protection pipe 5 meter long for protection of earthing lead complete all as specified and directed. (e) Requisite quantity of common salt and charcoal. (f) Testing of earthing.

Supply & lay cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of complete all as specified and directed by Engineer-in-Charge for the following:-

70 Sqmm 3.5 Core

50 Sqmm 3.5 Core

16 Sqmm 4.0 Core

10 Sqmm 2.0 Core

Excavation in trenches, in any type of soil not exceeding 1.5 Mtr wide and not exceeding 1.5 Mtr in depth , laying of cable or pipes (where provided for protection of cable) etc and getting out trimming the sides, forming bottom surfaces to required level complete all as specified and directed by Engineer-in-Charge

Material & labour for sand cushioning with a layer of sand 80 mm thick before laying of cable and 150 mm thick after laying of cable in trenches well ramming and spreading in layers complete all as specified and directed by Engineer-in-Charge.

Supplying & laying un-reinforced precast concrete cable cover class LV, type - 2, flat, size 300x 180 x 40 mm complete all as specified and directed by Engr-in-Charge

Supply & laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 4 sq. mm nominal cross section 2.0 core in service connections complete all as specified and directed by Engineer-in-Charge.

Supply & laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 6 sq. mm nominal cross section 2.0 core in service connections complete all as specified and directed by Engineer-in-Charge.

Supply & fixing LED flood light 120 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp complete all as specified and directed by Engineer-in-Charge. .

Material & labour for boring under roads / pavement / hard standing without disturbing the top surface by trenchless technology using ultra sounding technique and necessary machine including HDPE pipe of 150 mm dia suitable for 0.4 mpa working pressure for passing through the cables complete all as specified and directed by Engineer-in-Charge. Note : Necessary infrastructure required for boring shall be arranged by the Contractor at his own cost. .

Material & labor for earthing complete with copper earth plate electrode 60 cm x60 cm x 3.15 mm thick buried directly in ground ,(Earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level ,connected to and including copper earth strip 20X3mm by means of nut, bolts, check nuts and washers of copper/ bronze as shown in electrical plate No.3 of SSR Part-I (2009) complete all as specified and directed including testing on completion including the material and labour complete all as specified and directed by Engineer-in-charge of the following : - (a) Excavation and earth work for drilling hole for electrode in any type of Soil. (b) PCC pit in cement concrete 1:2:4 type B-1, Pre cast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than1.87 Kg/ Sq meter. (c) Funnel with watering pipe of GI 20 mm nominal bore light grade and lugs etc complete all as specified and directed (d) 40 mm nominal bore medium grade GI protection pipe 5 meter long for protection of earthing lead complete all as specified and directed. (e) Requisite quantity of common salt and charcoal. (f) Testing of earthing.

Material & labor for Chemical earthing complete with copper plate electrode (98 percent conductivity when annealed)of size 90 cm x 60cm x 5 mm thick burried directly in ground vertically to a depth not less than 2.25 mtr deep below ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level connected to and including copper strip(98 percent conductivity when annealed) 32 x 6 mm upto 7.5 mtr long by means of means of copper/brass bolt, nut, check nuts and washers besides brazing at all joints with GI protection pipe of 40mm bore medium grade up to 7.5 metre and connected to earthing test point all as shown in electrical plate No.3 of SSR part-I and as specified or indicated and testing on completion including excavation & eartwork in any type of soil, PCC (1:3:6) type C-2 chamber, precast slab 50mm thick in cement concrete (1:2:4) type B1 (reinforced with welded steel wire fabric (XPM) of weight not less than 4 Kg/Sqm), with frame, funnel with 20mm bore GI pipe medium grade watering pipe, wire mesh and lugs test point etc including 150 mm of magnesium sulphate above the top layer of salt and spreading evenly all round the plate and filling remaining with vegetable soil upto PCC chamber bottom and testing on complete all as specified and directed by Engineer-in-charge NOTE: On testing, after completion, if the earth resitance less than desired is not obtained, earthing will be regenerated at no extra coas till the desired earth resistance is obtained.

Supply & fix copper strip 20 x 3.15mm with saddles and fixing screws etc.for jointing with earth pits complete all as specified and directed by Engineer-in-charge

Material & labor for cutting the existing LT 9m steel pole and fixing the flood lights on cross arms at a height of 4m from ground level all as specified and directed by Engr-in-Charge (Old cutted pole to be deposited in MES store yard. Flood lights will be measured in appropriate item) complete all as specified and directed by Engineer-in-charge

Supply & fix GI tubing 50 mm bore, medium grade, ISI marked, with and including all fittings such as bends, elbows, tees, short pices etc complete laid in trenches or walls complete all as specified and directed by Engineer-in-Charge

Supply & fix GI tubing 25 mm bore, medium grade, ISI marked, with and including all fittings such as bends, elbows, tees, short pices etc complete laid in trenches or walls complete all as specified and directed by Engineer-in-Charge

Cutting of existing steel tubing for alterations or addition in position without taking down and screwing for addition of Tee, etc for 20 mm bore connection complete all as specified and directed by Engr-in-Charge. ( Note :- The cost of excavation , earthwork and fitting of pipe line required at site shall be deemed to be included in unit rate quoted by the tenderer)

Supply & fix gun-metal, globe or gate valves 25mm, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in hard /dense soil complete all as specified and directed by Engineer-in-Charge.

Material & labour for plain Cement concrete, type D2, (1:4:8), (using 40mm graded stone aggregate) in foundation and filling mass concrete complete all as specified and as directed by Engineer-in-Charge. .

Material & labour for reinforced cement concrete (design mix M 30) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed by Engineer-in-Charge. .

Material & labour for reinforced cement concrete (design mix M 30) in columns, pillars, piers, posts and struts complete all as specified and as directed by Engineer-in-Charge.

Material & labour for reinforced cement concrete (design mix M 30) in Beams, cantilevers, bressummers,lintels over 1.5m span complete all as specified and as directed by Engineer-in-Charge.

Material & labour for reinforced cement concrete (design mix M 30) in Chajjas complete all as specified and directed by Engineer-in-Charge.

Formwork to sides of concrete fdn, footing, bases of columns etc for rough finished surfaces of concrete complete all as specified and directed by Engineer-in-Charge.

Formwork to sides of concrete columns etc for rough finished surfaces of concrete complete all as specified and directed by Engineer-in-Charge.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for rough finished surfaces of concrete complete all as specified and directed by Engineer-in-Charge

Formwork to sides and soffits chajja of concrete etc for rough finished surfaces of concrete complete all as specified and as directed by Engineer-in-Charge.

Material & labour for rendering (external) 15mm thick in cement mortar 1:4 on brick walls/concrete surfaces mixing with WPC as per manu-factures instruction, plastered surfaces finished even and smooth with-out using extra cement complete all as specified and directed by Engineer-in-Charge

Material & labour for rendering 10mm thick in cement mortar 1:6 on internal fair faces of brick walls or on concrete surfaces, finished even and smooth W/O using extra cement complete all as specified and directed by Engineer-in-Charge

Supply & fix TMT bars 6 to 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia complete all as specified and directed by Engineer-in-Charge.

Material & labour for cement concrete 1:3:6 (using 40mm graded stone aggregate), 75mm thick as in plinth protection/path, etc., laid in alternate bays, finishing concrete surfaces even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge

Supply & fix anodised aluminum frame for doors, windows, ventilators with one or more rebates including jointing cleat for fixing etc complete all as specified and directed by Engr-in-Charge.

Supply & fix anodised aluminium door / window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and as directed by Engineer-in-Charge.

Supply & fix anodised aluminium grill( anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with CP brass/ stainless steel screws @ 200 mm c/c, incl cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening complete all as specified and as directed by Engineer-in-Charge.

Supply & fix stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples and fixed complete all as specified and as directed by Engineer-in-Charge.

Supply & fix sheet glass, 5.50mm ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane complete all as specified and as directed by Engineer-in-Charge..

Material & labour for rendering or bedding layer 10mm thick in cement mortar 1:4 on walls, etc. for fixing tiles as skirtings, dados, etc complete all as specified and directed by Engineer-in-Charge.

Material & labour for screed bed or bedding layer 15mm thick in cement mortar 1:6 for laying floor finishes/tiles complete all as specified and directed by Engineer-in-Charge. .

Material & labour for vetrified ceramic tiles 10 mm thick dark shade (square/rectangular ) polished , area of each tiles not exceeding 0.36 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed by Engineer-in-Charge.

Material & labour for vetrified ceramic tiles 10 mm thick dark shade (square/rectangular ) polished , area of each tiles not exceeding 0.36 sqm , in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed by Engineer-in-Charge.

Material & labour for preparing new treated surfaces by washing, rubbing down and stopping and applying two coats of distemper over a coat of primer over wall care putty complete all as specified and directed by Engineer-in-Charge

Material & labour for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed by Engineer-in-Charge.

Material & labour for treating the back fill in contact with foundation @ 7.5 ltr of emulsion per sqm of vertical surface layer of the str in contact with back fill to be measured complete all as specified and directed by Engineer-in-Charge.

Material & labour for treating the top surface of filled earth at @ 5 ltr chlorophyrophos of emulsion per square meter of surface complete all as specified and directed by Engineer-in-Charge

Material & labour for treating the soil under plinth protection at the rate of 5 ltr of emulsion per sqm of surface area complete all as specified and as directed by Engineer-in-Charge.

Supply & fix rotational moulded polythene white water storage tank tripple layared (cylindrical , vertical with closed top , ISI marked , ) hoisted and fixed in position all as specd in SSR Part 1 of capacity 1000 ltrs also including provision of 20 mm bore ball valves , high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum wt 455 gms) complete all as specified and directed by Engineer-in-charge.

Supply & fix 15mm dia GI Tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge

Supply & fix 20mm dia GI Tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge

Material & labour for cast iron nahni trap of 75 mm with grating incl jointing and waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed by Engineer-in-Charge

Supply & fix 100 mm ;bore sand cast type cast iron soil waste and vent pipes in any length , with or without ears with cement joints laid in trenches or in floors complete all as specified and directed by Engr-in-Charge.

Supply & fix vitreous china urinal bowl flat back, size of 465x 355 x 265 mm (white) with grating and union for discharge pipe incl providing and fixing plugs, bedding urinal against wall in CM 1:2 , securing urinal to plugs with and incl 60 mm long brass screws, pointing around urinal back in cementcomplete all as specified and as directed by Engineer-in-Charge.

Material & labour for cement concrete (1:3:6) type C-2 (using 40 mm graded aggregate) as in bed to drain pipe and packing under and haunching against the sides of pipes after they are laid and tested complete pipe size of 200mm bore complete all as specified and as directed by Engineer-in-Charge.

Material & labour for 200mm dia reinforced concrete pipes, class NP2, laid and jointed complete with collars complete all as specified and as directed by Engineer-in-Charge.

Removing excavated meterial to a distance n.exc 250m & depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed by Engineer-in-Charge..

Material & labour for false ceiling of perforeted particle board/tiles 60X60 cm in size and 12mm thick fixed with nails to timber frame work or with staples on snap grid fixed with screws complete all as specified and directed by Engineer-in-Charge.

Material & labour for anodised aluminium snap grid frame work for false ceiling complete all as specified and directed by Engineer-in-Charge. .

Material & labour for mild steel plates, plain or chequered, 5 mm thick or over in thickness in available sizes. Fe-410 W (Gde-E-250) quality-A complete all as specified and as directed by Engineer-in-Charge.

Material & labour for preperation of new or prevously untreated steel surfaces of any description over 10cm in width or girth ,not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed by Engineer-in-Charge.

Material and labour for point wiring complete with 4.0 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 volts grade ISI marked drawn through and including PVC CASING & CAPPING INCLUDING accessories etc including fixed to wall/ceiling including provision of 4.0 sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed as earth wire continuity complete all as specified and directed by Engineer-in-Charge

Supply & fix ceiling rose surface bakelite 65x50 mm three terminal etc complete all as specified and directed by Engineer-in-Charge.

Msupply & fix switch piano, flush type single pole one way 5 Amps complete all as specified and directed by Engineer-in-Charge

Supply & fixing LED luminaire 600 mm x 600 mm, 40 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed by Engineer-in-Charge.

Supply & fix switch socket out let 2 in 1, 5 Apms flush type multi purpose 5 pin ISI marked white or ivory complete all as specified and directed by Engineer-in-Charge.

Supply & fix switch socket outlet multipurpose 3 pin 5/15 Amp flush type universal controlled by one switch white or ivory ISI marked complete all as specified and directed by Engr-in-Charge.

Supply & fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE, five star rated with brushless direct current motor (BLDC) complete all as specified and as directed by Engineer-in-Charge.

Supply & fix MCB SPN 32 Amps, 230 volts C curve 10 KA complete all as specified and directed by Engineer-in-charge.

Supply & fix MCB SP 6 to 32 Amps, 230 volts C curve 10 KA complete all as specified and directed by Engineer-in-charge.

Supply & lay GI tubing medium grade of dia 20 mm including all fitting such as elbow, tee, socket , cutting, threading complete all as specified and directed by Engineer-in-Charge.

Supply & fix gun-metal, globe or gate valves 20mm, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

Material & labour for cutting the existing GI pipe of size 525 mm dia and taking 25 mm dia and taking 20 mm dia branch connection including necessary fittings etc complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches not exc. 1.5m wide and not exc. 1.5m in depth for foundation (laying of under ground cables and PCC pole) etc or for shafts, wells, cesspits, manholes pier holes etc not exc. 10sqm on plan and not exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed by Engineer-in-Charge.

Supply & lay ISI marked & conforming to IS - 5820 - 1970 unreinforced precast concrete cable cover Class LV, flate size 250mm X 150 mm X 40 mm in trenches as protection to LT UG cable complete all as specified and directed by Engineer-in-Charge.

Supply & fix solar LED street Light, 30 watt LED luminary all in one integrated including 12.8 Volt, 30 AH lithium ion phosphate battery, panel 60Wp monocrystalline suitable for installation on 80mm GI pipe incl clamps for mounting and with charge controller inclusive of internal wiring complete all as specified and directed by Engr-in-Charge.

Supply & fix GI pipe medium grade of 80 mm bore with suffiicient PCC above and under the ground complete all as specified and as directed by Engineer-in-Charge.

Material and labour for point wiring complete with 1.5 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 volts grade ISI marked drawn through and including PVC CASING & CAPPING INCLUDING accessories etc including fixed to wall/ceiling including provision of 1.5 sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed as earth wire continuity complete all as specified and directed by Engineer-in-Charge for following:-

One light point controlled by one, one way switch single pole piano type .

One Fan/exhaust point controlled by one, one way switch single pole piano type each .

One 3 pin 5/6 Amps socket out let on independent board .

One 3 pin 5/6 Amps socket out let on same board .

Supply & fixing wall mounted decorative ultra slim LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack instant start with uniform light distribution 20 W 4 ft indoor decorative (white) with 2 Core copper wire from ceiling rose to light fitting complete all as specified and directed by Engineer-in-charge. .

Supply and fix double door sheet metal enclosures factory made DBs protection class IP-43, suitable for fixing of MCBs, Isolators etc, confirming to IS 13032 SPN 8 ways with 200 Amp rated bus bar 415 volts powder coated complete all as specified and directed by Engineer-in-Charge.

Supply & fix isolators/MCBs of the under mentioned type and rating and fixing in DBs (DBs measured and paid for separately) (Note :- Make of the isolator should be the same as that of DB) complete all as specified and directed by Engineer-in-Charge for the following:-

MCB SPN of 240 volts 5-20/32/40 Amps Capacity, 'C' series, 10 KA

MCB SP of 240 volts 5-40 Amps Capacity, 'C' series, 10 KA

Supply & fix exhaust fan, steel body AC single phase. 230V of size 300m sweep with, blades, and frame and louvers incl necessary cutting in steel and making suitable hole for fixing exhaust fan complete all as specified and directed by Engineer-in-Charge. .

Supply & fix 400mm pedestral fan 230V with highspeed 2100RPM, 135 watts ,copper winding motor, fuse to protect during thermal overload and finger proof safety grill, aerodynamically balanced sturdy PP blade and a strong base for stability, white colour complete all as specified and as directed by Engineer-in-Charge..

Msupply & fix switch piano, flush type single pole one way 5 Amps complete all as specified and directed by Engineer-in-Charge

Supply & fix switch socket outlet, 5 pin, 5 Amp, piano type complete all as specified and directed by Engineer-in-Charge

Supply & fix ceiling rose surface bakelite 65x50 mm three terminal etc complete all as specified and directed by Engineer-in-Charge.

Supply & fix 12 Volt 180 AH sealed maintenance free battery, made in a modern and eco friendly manufacturing facility, lead calcium grid fro extended life, wide operating temp range, low self- discharge and long service life, leak proof construction, fast deep charging recovery, vibration resistant, corrosion resistant along with trolley complete all as specified and directed by Engineer-in-Charge.

Design, supply, installing and testing polycrstalline solar panel of 500 Watt, 24 Volt, with 144 cells alluminium body with module efficiency 17.8%, operating temp -40 to +80 degree C with necessary cables for connection from Solar panel to inverter complete all as specified and directed by Engr-in-Charge Note : The rates of frame for installation of solar panel and cables from solar panel to inverter deemed to be included in quoted rates

Supply & connection of Inverter of capacity 24 Volt 1500 VA, rated power 1260Watt, versatlie and compatible with 12V batteries ranging from 135 AH to 220 AH,rapid battery charging at low input voltage, supports Eco and UPS mode, twin socket output for power load as well as regular load with intelligent output load optimization feature, supports all batteries type and also provn of enhanced protection through MCB with suitable capacity along with trolley for carrying 01X 12 V 180 AH SMF battery and inverter complete all as specified and as directed by Engineer-in-Charge Note : Rates of battery will be measured under appropriate item .

Note for item No 150.00 to 163.00 The work provn of of solar security lights at mangwana hills at AF Stn Bhuj mentioned at para 2.1 (c) on page No 86 of tender documents located appx 45 KM from AF Stn Bhuj & the work to be executed at top of the hills which is @ appx 2 KM from foot of the hills. Moreover no road/transport facilits is available to reach the top of the hills for manpower & materials. Bidders are to be advised to visit the site before quoting the rates & no extra claim on this account will be admissible.

M/s Bombay Novelty Stores