SPECIAL REPAIRS TO BLDG NO P127 SNCOS MESS AT AF STATION SURYALANKA

Amount

SCHEDULE 'A'

Taking down cement or cement lime plaster, any description, on brick walls including raking out joints hacking for key scrubbing down with water etc. complete all as specified and directed by Engineer-in-Charge

M&L for rendering 5mm thick on fair faces of concrete surfaces in cement mortar 1:3 in ceiling surface finished even and smooth with out using extra cement complete all as specified and directed by Engineer-in-Charge

M&L for rendering 10mm thick on fair faces of brick or concrete in CM 1:6 finished even and smooth with out using extra cement complete all as specified and directed by Engineer-in-Charge

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in two layers, first layer 10 mm thick in CM 1:6 and second layer 5 mm thick in CM 1:4 finished fair and even mixed with WPC as per manufacturer's instructions complete all as specified and directed by Engineer-in-Charge (Note : Supply of water proofing compound shall be measured and paid seperately).

Supply only integral water proofing compound of approved make complete all as specified and directed by Engineer-in-Charge

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), and aprons removing serviceable tiles to store and rubbish off the premises all as specified and directed by Engineer-in-Charge

M&L for joint free non Skid ceramic coloured tiles (matt finish) 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 15 mm thick screed in cement mortar 1:6 all as specified and directed by Engineer-in-Charge.

M&L for Non Skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15 mm thick screed in cement mortar 1:6 all as specified and directed by Engineer-in-Charge.

M&L for vitrified ceramic tiles 10mm thick light shade (square/ rectangular) polished, area of each tile not exceeding 0.36 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed in cement mortar 1:4 complete all as spd and as directed by Engr-in-Charge.

M&L for vitrified ceramic tiles 10mm thick light shade in vertical surfaces as in dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 10mm thick screed in cement mortar in cement mortar 1:4 all as specified and directed by Engineer-in-Charge.

M&L for coloured glazed tiles in vertical surfaces 350 x 250 x 7mm/450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and inlcuding 10mm thick screed bed in cment mortar 1:4 complete all as specified and directed by Engr-in-Charge.

M&L for 18-20 mm thick Granite stone slabs of any type machine cut bedded and jointed with grey cement slurry and pointed with white cement with admiture of pigment to match the shade of granite stone including grinding and polishing laid over and including 15 mm thick screed in cement mortar 1:6 all as specified and directed by Engineer-in-Charge.

M&L for 18-20 mm thick Granite stone slabs of any type machine cut, in skirting/dado bedded and jointed with grey cement slurry and pointed with white cement with admiture of pigment to match the shade of granite stone including grinding and polishing laid over and including 10 mm rendering in cement mortar 1:4 all as specified and directed by Engineer-in-Charge.

Taking down chowkats or frames (without taking off shutters from frame) not exceeding 1.5 sqm each including making good disturbed portions with PCC 1:2:4 type B-0 or in cement mortar 1:4 after removal of frames all as specified and directed by Engineer-in-Charge..

S&F of vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap, and to flushing pipe, anti-syphonage pipe, etc., fixed in repairs complete including making good to floor all as specified and directed by Engrineer-in-Charge.

S&F of 10 lit capacity PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, fixed in repairs, all as specified and directed by Engineer-in-Charge.

S&F in repairs Vitreous China wash basin, white, flat back, of size 550x400 mm excluding taps, waste chain and plug and porcelain stopper but including brackets and brass, 32 mm dia chromium plated waste fitting and 40 mm bore PVC waste pipe all as specified and directed by Engineer-in-Charge.

S&F in repairs of CP Pillar taps fancy type 15 mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe, all as specified and directed by Engineer-in-Charge..

S&F in repairs of 20 mm bore Gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed all as specified and directed by Engineer-in-Charge..

S&F in repairs of Stop valves 15 mm bore, cast copper alloy screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions, all as specified and directed by Engineer-in-Charge..

S&F in repairs 15 mm bore Bib taps, chromium plated, cast copper alloy, screwed down, screwed for iron pipe, all as specified and directed by Engineer-in-Charge.

S&F of PVC connections 15mm size with PTMT nuts of length 450 mm all as specified and directed by Engineer-in-Charge.

S&F of Towel rail 600 mm long of PTMT minimum weight 190 gms, fixed with and including chromium plated brass screws and wooden / plastic cleats all as specified and directed by Engineer-in-Charge..

S&F of 20 mm outer dia 3 layer PP-R poly-propylene random copolymer concealed pipes SDR 7.4 (PN-16) UV stabilized and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc., including taking up or down steel tubing and connections all as specified and directed by Engineer-in-Charge.

S&F of 25 mm outer dia 3 layer PP-R poly-propylene random copolymer concealed pipes SDR 7.4 (PN-16) UV stabilized and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc., including taking up or down steel tubing and connections all as specified and directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces of walls and applying two coats of exterior weather coat paint over a coat of primer all as specified and directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces of ceilings and applying three coats of white wash all as specified and directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces of walls and applying three coats of white wash all as specified and directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer all as specified and directed by Engineer-in-Charge.

M&L for preparation of old painted surfaces of walls and applying one coat of oil bound distemper all as specified and directed by Engineer-in-Charge

S&F of 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls or laid in floors as in soil, waste and pipes including dismantling of old pipes all as specified and directed by Engineer-in-Charge

S&F of 110 mm bore PVC (SWR) bends any radius provided with access door, fixed in repairs all as specified and directed by Engineer-in-Charge

S&F of 110 mm bore PVC (SWR) junction, single (Single T) equal or unequal provided with access door, fixed in repairs all as specified and directed by Engineer-in-Charge

S&F of 110 mm bore PVC (SWR) Vent cowl fixed in repairs all as specified and directed by Engineer-in-Charge

S&F of 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls or laid in floors as in soil, waste and pipes including dismantling of old pipes all as specified and directed by Engineer-in-Charge

S&F of 75 mm bore PVC (SWR) bends any radius provided with access door, fixed in repairs all as specified and directed by Engineer-in-Charge

M&L PVC (SWR) floor trap 75mm dia plain with grating including jointing with solvent cement , fixed in repairs all as specified and directed by Engineer-in-Charge

Dismantling of old water tank exc 250 Ltr & n.exc 500 Ltr capacity and removing from store etc all as specified and directed by Engineer-in-Charge

Dismantling of old water tank exc 500 Ltr & n.exc 1000 Ltr capacity and removing from store etc all as specified and directed by Engineer-in-Charge

S&F rotational moulded polyethylene water storage tanks IS : 12701 - 1996 marked (cylindrical vertical with closed top) of 1000 Ltrs capacity with and including 20mm dia Ball brass valve high pressure with polythene float and fly nut screwed for iron pipe or brass and fixed etc all as specified and directed by Engineer-in-Charge

S&F rotational moulded polyethylene water storage tanks IS : 12701 - 1996 marked (cylindrical vertical with closed top) of 500 Ltrs capacity with and including 20mm dia Ball brass valve high pressure with polythene float and fly nut screwed for iron pipe or brass and fixed etc all as specified and directed by Engineer-in-Charge

M&L for ACP (aluminium composite panel) wall cladding with 4.5mm thick of approved colour using mascon tapes (spacer tapes) global or equivalent, silicon sealant rest bond or equivalent, stainless steel anchor fastener and necessary hardware etc tied oer and including mild steel frame work with 50 x 25 x 1.5mm hollow section zinc coated, grid of size 1.2m x 1.2m including necessary welding etc complete and fixed all as per manufacturers insturctions and all as specified and directed by Engineer-in-Charge

M&L for complete removal of existing treatment by wire brushing , sand papers, other scrapping material as required , preparing the surface by filling the nail holes , cracks , other holes & complete filling using 3mm wall care putty and making the surface smooth and applying two coat oil bound distemper over a coat of primer complete all as specified and directed by Engr-in-charge.

Demolition and breaking up drain pipe 150mm dia (salt glazed ware, AC or reinforced concrete) set in cement mortar including bedding and haunching complete all as specified and directed by Engr-in-charge.

M&L for Plain cement concrete bed 100mm thick for 150mm bore drain pipes in 1:4:8, type D-2, using 40mm graded stone aggregate including packing under and haunching against the sides of pipes of after they are laid and tested complete all as specified and directed by Engr-in-charge.

M&L for salt glazed stone ware drain pipes, Grade "A", 150mm dia (internal dia) laid in trenches and jointed with CM 1:1 complete all as specified and directed by Engr-in-charge.

Excavation in trenches, n.exc 1.5m wide and n.exc 1.5m in depth for replacement of sewage lines ang getting out soft/loose soil complete all as specified and directed by Engr-in-charge.

Returning, filling in, including spreading, levelling, watering & well ramming in layers n. exc 25 cm in soft/loose soil complete all as specified and directed by Engr-in-charge.

Removing excavated soil n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed by Engr-in-charge.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed by Engr-in-charge.

M&L Plain cement concrete 1:2:4, type B-0 using 12.5mm graded stone aggregates as in coping including necessary formwork, weathering, slightly rounded or chamfered angles, finishing of exposed surfaces of concrete to even and smooth without using extra cement complete all as specified and directed by Engr-in-charge.

M&L for pre-cast RCC 1:2:4, type B-1 using 20mm graded stone aggregates as in cover slabs sets in CM 1:6 including all necessary formwork and exposed surfaces of concrete shall be finished even and smooth without using extra cement complete all as specified and directed by Engr-in-charge.

M&L for TMT steel bars 8mm dia cut to length bent to shape required including cranking, hookin ends and binding with mild steel wire (annealed not less than 0.90mm dia) complete all as specified and directed by Engr-in-charge.

Taking down chowkats or frames (without taking off shutters from frame) exceeding 1.5 sqm but not exceeding 4 Sqm each including making good disturbed portions with PCC 1:2:4 type B-0 or in cement mortar 1:4 after removal of frames complete all as specified and directed by Engr-in-charge.

M&L for powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleats for fixing etc., complete all as specified and directed by Engineer-in-charge.

M&L for powder coated Aluminium anodised doors shutters, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, handles 2 Nos in each door, hinges, anodised aluminium snap beadiing screws etc complete all as specified and directed by Engr-in-charge.

M&L for 12mm thick prelaminated particle board exterior grade prelaminated on both sides with decorative choise lamination fixed in aluminium frame work complete all as specified and directed by Engr-in-charge.

S&F mortice lock vertical type of size 100mm long four lever of brass complete all as specified and directed by Engr-in-charge.

S&F door closer, aluminium die cast body, hydrauically regulated designation No 03 universal type, suitable for door shutters of 851 to 1000mm in width and weight between 61 to 80 kg complete all as specified and directed by Engr-in-Charge

S&F floor door stopper 150mm length of aluminium alloy body and tongue, anodised with hard drawn steel spring complete all as specified and directed by Engr-in-Charge .

S & F of Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or wooden/aluminium beeds all as specified and directed by Engr-in-Charge ..

S&F of 4.8 mm thick Sheet Glass, ordinary quality and glazing with aluminium beads all as specified and directed by Engr-in-Charge ..

S&F of Pressed steel frames 125 x 60mm size for doors with bouble rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed all as specified and directed by Engr-in-Charge ..

M&L for Plain cement concrete 1:3:6 type C-0 using 12.5 mm graded stone aggregate for filling of hollow portions of door frames etc., all as specified and directed by Engr-in-Charge ..

S&F of 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides all as specified and directed by Engr-in-Charge ..

S&F for 35 mm thick second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass,gauze etc. divided in to squares, with plain chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamferred or rounded, fitted with cut and mitred beads for securing glass, wire gauge etc. ; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) fitted to chowkats all as specified and directed by Engr-in-Charge ..

M&L for Preparing new or previously un treated surfases of wood and wood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer all as specified and directed by Engr-in-Charge .

M&L for preparing new or previously untreated surfaces of steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed by Engr-in-Charge.

S&F of factory made PVC Solid Door frame of size 50mmx47mm made out of 5mm plain coloured PVC sheet reinforced with MS Square tube, fixed in opening as per specification all as specified and directed by Engr-in-Charge.

S&F of Factory made Solid panel PVC Door Shutter of 30mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colourr PVC 'C' channel having a PVC sheet strip 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; Panelling of plain clour PVC sheet to be fitted in the MS frame welded / sealed to the styles & rails with suitable PVC sheet beeding and jointed together with solvent cement as per specification and all as specified and directed by Engr-in-Charge.

M&L for powder coated Aluminium anodised window and ventilators shutters, side hung type without sash bars, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beadiing, screws, anodised alunimium fittings such as peg stays 150mm long (01 No) hinges type (B-21) 100mm long (2 Nos) suitable handle (1 No) etc complete all as specified and directed by Engr-in-Charge.

S&F 200 mm long Aluminium anodised barrel tower bolts of extruded aluminium section all as specified and directed by Engr-in-Charge.

S&F 150 mm long Aluminium anodised barrel tower bolts of extruded aluminium section all as specified and directed by Engr-in-Charge.

S&F of 150 mm long Aluminium alloy handles cast type anodised all as specified and directed by Engr-in-Charge.

S&F of 100 mm long Aluminium alloy handles cast type anodised all as specified and directed by Engr-in-Charge.

S&F 75 mm long Aluminium butt hinges extruded aluminium alloy with galvanised steel wire pin anodised, type C-22 all as specified and directed by Engr-in-Charge.

S&F of 300 mm long aluminium alloy anodised sliding door bolts with hasp and staple (bolt type) and fixing clip of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy all as specified and directed by Engr-in-Charge.

S&F of Mild steel 300 mm ,ordinary rat & tail rod pattern springs including roller and roller plate all as specified and directed by Engr-in-Charge.

Taking down carefully by unscrewing from boards / outlet boxes , fittings and fixtures such as ceiling /wall mounted tubelight fittings , etc complete all as specified and as directed by Engr-in-Charge..

Taking down of ceiling fan complete , removing the down rod / pendent of length not less than 1.5 mtr , brass with cord grip pattern , and 0.5 Sqmm copper flexible twisted twin cord up 1.5m length for refixing ceiling fan after false ceiling complete all as specified and as directed by Engr-in-Charge.

M&L for point wiring complete with 1.5 Sqmm single core multistranded copper conductor, FRLS, PVC insulated unsheathed cable 1100 volts grade fixed in and including concealed PVC conduit, fitting and accessories, joints boxes including one 1.5 sqmm copper FRLS PVC insulated unsheathed as earth continuity conductor connected in the common earth complete all as specified and as directed including taking down existing point wiring for Light/ Fan/ Exhaust fan/ Independent 5 A Socket/ Security light complete all as specified and as directed by Engr-in-Charge.

All as per Item No.83 above but with 4 sqmm single core wiring for Phase,neutral and earth for Independent 15 Amps power socket complete all as specified and as directed by Engr-in-Charge.

All as per item No. 83 above but for One 5 pin socket outlet 5 amps on same board controlled by one switch complete all as specified and as directed by Engr-in-Charge.

S&F in replacement Modular socket, 6A, 5 pin combination 2 module complete all as specified and as directed by Engr-in-Charge.

S&F in replacement modular switch socket combination 16A, 6 pin, 3 module complete all as specified and as directed by Engr-in-Charge.

S&F in replacement modular switch one way 6 Amps, 1 module complete all as specified and as directed by Engr-in-Charge.

S&F in replacement of modular Fan regulator electronic step type, 120W- 2 module, 240V single phase complete all as specified and as directed by Engr-in-Charge.

S&F in replacement modular white cover plate with frame and metal flush box, 2 module complete all as specified and as directed by Engr-in-Charge.

S&F in replacement modular white cover plate with frame and metal flush box, 3 module complete all as specified and as directed by Engr-in-Charge.

S&F in replacement modular white cover plate with frame and metal flush box, 8 modulecomplete all as specified and as directed by Engr-in-Charge.

S&F in replacement ceiling rose, 3 plate PVC/polycarbonate, isolated body complete all as specified and as directed by Engr-in-Charge.

S&F in replacement submain wiring with two run of single core cable FRLS PVC insulated sheathed cable 1100 volts grade 4 Sqmm copper multistranded conductor including and drawing into concealed/Surface PVC conduit, fixed on/in wall, ceiling including 4 sqmm FRLS PVC insulated unsheathed multistranded for earth wire connected to earth complete including taking down existing submain wiring complete all as specified and as directed by Engr-in-Charge. Note :- Three run of 4 sqmm calbe and one run of PVC Conduit shall be measured as one RM

S&F in replacement submain wiring with two run of single core cable FRLS PVC insulated sheathed cable 1100 volts grade 6 Sqmm copper multistranded conductor including and drawing into concealed/Surface PVC conduit, fixed on/in wall, ceiling including 6 sqmm FRLS PVC insulated unsheathed multistranded for earth wire connected to earth complete including taking down existing submain wiring complete all as specified and as directed by Engr-in-Charge. Note :- Three run of 6 sqmm calbe and one run of PVC Conduit shall be measured as one RM

S&F in replacement submain wiring with two runs of single core cable FRLS PVC insulated sheathed cable 1100 volts grade 10 Sqmm copper multistranded conductor including and drawing into concealed/Surface PVC conduit, fixed on/in wall, ceiling including 10 sqmm FRLS PVC insulated unsheathed multistranded for earth wire connected to earth complete including taking down existing submain wiring complete all as specified and as directed by Engr-in-Charge. Note :- Three run of 10 sqmm calbe and one run of PVC Conduit shall be measured as one RM

S&F in replacement Metal Clad enclosure with Socket and earth plug alongwith one Double Pole MCB 20Amps, C Curve, 10 kA, complete all as specified and as directed by Engr-in-Charge.

Taking down of Exhaust fan complete, removing the blades, frame, cleaning of complete oil/ grease over the fan and refixing the same with 0.5 sq.mm copper flexible twisted twin cord up to ceiling rose/ connector complete all as specified and as directed by Engr-in-Charge.

Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 5 connected to earthing test point including testing on completion and complete all as specified and as directed by Engr-in-Charge.

S&F in replacement of MCB DB Double Door, TPN 4 way (4+12) IP 54, fixed to wall in concealed by distrubing the exisitng wall surface and making good complete all as specified and as directed by Engr-in-Charge

S&F in replacement of MCB DB Double Door, SPN 8 way IP 54, fixed to wall in concealed by distrubing the exisitng wall surface and making good complete all as specified and as directed by Engr-in-Charge

S&F in replacement of MCB DB Double Door, SPN 4 way IP 54, fixed to wall in concealed by distrubing the exisitng wall surface and making good complete all as specified and as directed by Engr-in-Charge

S&F in replacement of MCB Four Pole 63 Amps, C Curve, 10 kA, complete all as specified and as directed by Engr-in-Charge

S&F in replacement of MCB Double Pole 40 Amps, C Curve, 10 kA, complete all as specified and as directed by Engr-in-Charge

S&F in replacement of MCB Double Pole 6-32 Amps, C Curve, 10 kA, complete all as specified and as directed by Engr-in-Charge

S&F in replacement of MCB Single Pole 6-32 Amps, C Curve, 10 kA, complete all as specified and as directed by Engr-in-Charge

S&F in replacement 4 Feet LED Tube light of 20 Watt with surface and wall mounted Batten,extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver connected upto ceiling rose including taking down exisitng Tube light fitting of any type c complete all as specified and as directed by Engr-in-Charge Make: Havells Model: ENDURALINEARNEOBS20WLED865SPCWH or its equivalent in Philips/ Wipro/ Crompton/Bajaj

S&F in replacement 2 Feet LED Tube light of 10 Watt with surface and wall mounted Batten,extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver connected upto ceiling rose including taking down exisitng Tube light fitting of any type complete all as specified and as directed by Engr-in-Charge Make: Havells Model: ENDURALINEARNEOBS10WLED865SPCWH or its equivalent in Philips/ Wipro/ Crompton/Bajaj

S&F in replacement of exisiting Bldg Security light with 25 Watt LED New generation energy saving and environmental friendly long life light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP OPENING seperate driver compartment with IP66 protection and impact resistance of IK07 alongwith three core flexible copper connecting cable from light fitting to ceiling rose / connector complete all as specified and as directed by Engr-in-Charge Make: Havells Model No. ENDURAPEARSL25WLED757SASYTOPC or equivalent in Bajaj/ Phillips/ Standard/ C&S

S&F in replacement of GI Pipe bracket of dia 25 mm and length 1.5 RM bent to an angle as specified along with 2 Nos Clamps made up of FI 20x3 mm and fixed to wall complete all as specified and as directed by Engr-in-Charge

S&F in replacement of existing Post light of any type and wattage with New generation, LED Post Top light of wattage 25 Watt, energy saving, environmental friendly, long life aesthetically designed with symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs as light source complete and connecting up with exisitng cable complete all as specified and as directed by Engr-in-Charge. Make: havells, Model: RUBYPT25WLED757PSYMTOPC or its equivalent in Bajaj/ Philips/ CG

Total of Schedule 'A'

DHANA CONSTRUCTIONS