PROVISION OF CERTAIN SR/MR/MW WORKS UNDER AGE BR (P), BR-(II) AND AGE (E/M) AT AF STATION BHUJ

Taking down cement plaster of any description on brick walls , cement surfaces including raking out joints hacking for key secrubing down with water remove dust, debries/rubbish etc complete all as specified and directed by Engineer-in-Charge.

Material & labour for 10 mm thick rendering for fair faces of concrete surfaces on walls in CM 1:6 and finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge

Material & labour for rendering 15mm thick in Cement Mortar 1:4 (External) on brick walls or on concrete surfaces in two coats, 1st coat of 10mm thick and 2nd coat of 5mm thick including mixing with WPC to 2nd coat as per manufacturer's instructions, plastered surfaces finished even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge. NOTE : Integral water proofing compound shall be Measured and paid separately as ‘Supply only’ under relevant Items.

Supply only integral water proofing compound ISI marked complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparation of new or previously untreated concrete or PCC block masonry external surfaces and applying two coats of exterior emulsion paint over a coat of primer complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparation of old treated surfaces of wall including brooming down, scrapping down smoke soots etc. and appying one coat of white wash complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparation of old treated surfaces of ceiling including brooming down, scrapping down smoke soots etc. and appying one coat of white wash complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparation of old treated surfaces of wall surfaces and applying one coat of distemper with distemper oil emulsion white or tinted complete all as specified and as directed by Engineer-in-Charge.

Material & labour for preparation of old treated wall surfaces including brooming down and applying one coat of exterior emulsion paint complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparation of old wooden painted surfaces of any description exc 10 cm width or girth and appying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Material & labour for 25mm thick cement concrete type BO 1:2:4 using 12.5mm graded aggregate in sub base floors complete all as specified and directed by Engineer-in-Charge.

Material & labour for mat finish coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

Material & labour for non skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

Material & labour for glazed ceramic coloured tiles in vertical surfaces such as in skirting and dados 350x250x7mm/450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over plaster in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

Material & labour for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engineer-in-Charge.

Taking up on down steel tubing and connection incl cleaning for refining of the following bore of pipe complete all as specified and directed by Engineer-in-Charge of following size :-

15mm bore

20mm bore

Supply & fix CPVC pipes ISI marked, IS-15778 with all fittings for hot and cold water, fixed with solvent cement complete to walls and ceilings or laid in floors of complete all as specified and directed by Engineer-in-Charge of following size :-(SDR-13.5 )

15mm dia

20mm dia

Dismantling of cast iron, PVC or reinforced concrete pipes jointed in cement mortar and taking out of trenches, if required complete all as specified and directed by Engineer-in-Charge following bore of pipe

100/110mm dia

75 mm dia

Supply & fix PVC ultra drain,SelFit pipes, single socketed, ISI marked, IS-13592 type 'B' in any length, jointed with solvent cement fixed in walls and floors complete all as specified and directed by Engineer-in-Charge of following size :-

110mm dia

75 mm dia

Supply & fix PVC junction single 'Tee' equal with door opening, ISI marked, IS-14735, jointed with solvent cement complete all as specified and directed by Engineer-in-Charge of following size :-

110mm dia

75 mm dia

Supply & fix PVC sockets equal, ISI marked, IS-14735, jointed with solvent cement complete all as specified and directed by Engineer-in-Charge of following size :-

110mm dia

75 mm dia

Supply & fix pressed steel frames of size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock stricke plate etc complete all as specified and directed by Engineer-in-Charge.

Material & labour for providing cement concrete type B-0, 1:2:4 (using 12.5mm graded stone aggregate) as in roof kerbs, mud stops, filling in frames and the like rounded or or chamfered on edges complete all as specified and directed by Engineer-in-Charge.

Supply & fix 35mm thick 2nd class hard wood factory made glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc, with sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/ Gauge etc. Size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24(a) complete all as specified and directed by Engineer-in-Charge.

Supply & fix stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed wih SS wire staples complete all as specified and directed by Engineer-in-Charge.

Supply & fix 35mm thick 2nd class hard wood factory made plain framed, paneled shutters (any number of panels), with lock rail and panel of 9mm BWP commercial ply or 12mm veveered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (part-I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engineer-in-Charge.

Supply & fix Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening complete all as specified and directed by Engineer-in-Charge.

Supply & fix factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site complete all as

specified and directed by Engineer-in-Charge.

Supply & fix mild steel 300mm long ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engineer-in-Charge.

Material & labour for aluminium window with double side hung shutter for glazing and gauging and frame with one or more rebates made out anodised aluminium section including section for fixing of aluminium grills with suitable fixtures, jointing cleats for fixing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium beading screws, type B20 100mm long suitable handle and anodised aluminum fittings such as stay, hinges glazing with 5 mm thick tinted sheet glass and gauging with aluminium wire cloth of size 0.45mm dia of wire and 1.40mm aperture as per drg No. CEAA/TD/133 sheet No. 1/2 and 2/2 dated 13.12.02 except fixed glazing (FG) complete all as specified and directed by Engineer-in-Charge.(Tint of glass shall be approved by GE) Note :- Aluminium grill fixed under above item shall be measured and paid separately.

Supply only aluminium anodised grill of approved shape with opening in grill 66mm x 80mm (diagonally) or nearest to + 5mm made out of standard aluminium moulded section of size 6mm x 7mm complete all as specified and directed by Engineer-in-Charge.

Removing of old water proofing treatment including screed bed and cleaning the surface of slab with wire brushes removing dust, foreign materials including flushing at junction of wall and removing the rubbish off the premises to a distance exc. 500m, complete all as specified and as directed Engr-in-Charge.

Material & labour for PCC 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in roof kerbs/coping/ bed block / depression complete all as specified and directed by Engineer-in-Charge.

Material & labour for 15mm thick rendering in cement mortar 1: 4 on faces of brick work or concrete surfaces with WPC, finished even and smooth W/O using extra cement as in roof complete all as specified and directed by Engineer-in-Charge. (WPC shall be measured & paid seperately) .

Supply only integral water proofing compound. (ISI marked) complete all as specified and directed by Engineer-in-Charge.

Material & labour for cleaning as directed & specified all rust/ scales/corrosion from reinforcement bars using rust remover Reebaklens RR- Rust remover, cleaning and etching agent supplied in 1/2, 1 and 5 Litre containers, having Specific Gravity 1.16 - 1.22 @ 25°C. Reebaklens RR cleaning agent is a combination of acid based material, corrosion inhibitors and dispersing agents and is supplied as a clear green solution.Application of Reebaklens RR with brush for complete wetting of rusted metal surface and allowed to react it for 16-24 hours followed by cleaning the surface with wire brush and washing surface with fresh water as required to exposed reinforcement bars complete as specified.Note : Rates quoted for all items should include working upto 6m height including all necessary scaffolding , staging etc complete all as specified and directed by Engineer-in-Charge. HSE Guidelines : Recommended to wear tight-fitting, dust-resistant, chemical splash goggles if airborne dust is generated, Wear protective gloves. Wear appropriate clothing to prevent any possibility of skin contact. .

Lokfix E55- Styrene free vinyl-ester resin based cartridge system for anchoring reinforcement supplied in 300 ml cartidge with a single mixer nozzle, application inclueds drilling hole close to old reinforcement bar with suitable drill as per dia of bar, cleaning the hole with wire brush and compressed air, putting Lokfix E55 with gun followed by placing rebar with slide rotational motion to avoid air void formation etc complete as directed by EIC.(i) for 8mm dia (min embedment depth 80mm) (ii) for 10mm dia (min embedment depth 90mm) (iii) for 12 mm dia ( min embedment depth 110 mm) (iv) for 16 mm dia ( min embedment depth 125 mm) Note : Rates quoted for all items including all necessary scaffolding , staging etc complete all as specified and as directed. HSE Guidelines : Recommended to wear tight-fitting, dust-resistant, chemical splash goggles if airborne dust is generated, Wear protective gloves. Wear appropriate clothing to prevent any possibility of skin contact.

scaffolding and transportation etc. complete as per specification and as directed by Engg.-in-charge. Note : Rates quoted for all items should include working upto 6 m height including all necessary scaffolding , staging etc complete all as specified and as directed. HSE Guidelines : Recommended to wear tight-fitting, dust-resistant, chemical splash goggles if airborne dust is generated, Wear protective gloves. Wear appropriate clothing to prevent any possibility of skin contact. Barrier creams provide additional skin protection. Do not smoke during use. Maintaine ample ventilation. If contact wiith the resin occurs, wash immediately with a strong detergent or a resin removing cream. Eye contamination must be immediatelywashed with plenty of water and medical treatment sought. complete all as specified and directed by Engineer-in-Charge.

Material & labour for Polymer modified Mortar-Patch repair (Up to Grade M45) Providing and laying Renderoc SP 40- shrinkage controlled polymer modified single component, alkaline resistant fibre reinforced, thixotropic, cementitious patch repair mortar supplied in 25 kg moisture resistant bag when mixed with clean water at w:p ratio 0.18, achieves compressive strength (BS 1881 Pt.116) -> 20 Mpa at 1 day & > 45 Mpa at 28 days, Tensile Strength(BS 6319 Pt.7) > 2.5 Mpa at 28 Days, Flexural Strength(BS 6319 Pt.3)>7 Mpa at 28 days, Drying shrinkage to ASTM C 157-93, 28 days < 1000 microstrain. Typical application inclues mixing entire bag with clean water about 4.25L to 4.5 L, mixed in suitable container with heavy duty slow speed mixer machine to achieve uniform lump free mortar consistency, placing and finishing the same with trowel carefully compacting the same around the rebars and finishing to bring it in line with existing concrete surface on the beams, slabs, piles etc., where the thickness of application is less than 50 mm in patches as per specification after applying bonding coat. Item rate is inclusive of materials all labour, tools and tackles, scaffolding and transportation etc. complete as per specification and as directed by Engg.-in-charge.

Pulling down the existing U/S wires of any type from concealed wiring carefully of aluminium point wiring (light, fan, bell, socket, power point etc.) with or without conduit, along with all connected accessories such as ceiling rose, switches, sockets, switch boards, fan regulator etc complete all as specified and directed by Engineer-in-Charge.

POINT

Pulling out sub main wiring only any size of aluminium conductor cable PVC insulated with or without condiut complete all as specified and directed by Engineer-in-Charge.

Material & labour for point wiring complete with 1.5 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 volts grade ISI marked drawn through and including PVC CASING & CAPPING INCLUDING accessories etc including fixed to wall/ceiling including provision of 1.5 sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed as earth wire continuity with PVC surface box complete all as specified and directed by Engineer-in-Charge for :-

One light point controlled by one, one way switch single pole piano type.

One Fan point controlled by one, one way switch single pole piano type.

One 3 pin 5 Amp socket outlet on the same board.

One 3 pin 5 Amps socket out let on independent board.

One bell point controlled by one bell push on independent board.

Pulling out sub main wiring only any size of aluminium conductor cable PVC insulated with or without condiut complete all as specified and directed by Engineer-in-Charge.

Material & labour for point wiring complete with 1.5 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 volts grade ISI marked drawn through and including PVC CASING & CAPPING INCLUDING accessories etc including fixed to wall/ceiling including provision of 1.5 sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed as earth wire continuity with PVC surface box complete all as specified and directed by Engineer-in-Charge for :-

One light point controlled by one, one way switch single pole piano type.

One Fan point controlled by one, one way switch single pole piano type.

All as per item No.87.00 here-in-before but with 2.5 Sqmm Copper conductor cable for one 3 pin, 15 Amps socket out let on independent board complete all as specified and directed by Engineer-in-Charge.

continuity with new plastic laminated white coloured top sheet cover 3.0 mm thick on existing sunken box complete all as specified and directed by Engineer-in-Charge for :-

Supply and fixing in repairs wall mounted decorative ultra slim LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack instant start with uniform light distribution 18/20 W 2 ft indoor decorative (white) with 2 Core copper wire from ceiling rose to light fitting complete all as specified and directed by Engr-in-Charge

Supply & fixing in replacement of LED Lamp, 7 W ,Type of cap B22, wide operating range 140V -280V, Input current 08mA- 30mA, lumen 180-300, UV and IR free light, color temperature 6500K, cool day light, up to 80 % energy saving over GLS complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement double door sheet metal enclosures factory made DBs protection class IP-43, suitable for fixing of MCBs, Isolators etc, confirming to IS 13032 triple pole and neutral 4 ways with 200 Amp rated bus bar 415 volts powder coated complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement double door sheet metal enclosures factory made DBs protection class IP-43, suitable for fixing of MCBs, Isolators etc, confirming to IS 13032 single pole and neutral 08 ways with 200 Amp rated bus bar 415 volts powder coated complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement of isolators/MCBs, etc. In distribution board of the following rating and capacities complete all as specified and directed by Engineer-in-Charge of following :-

Supply & fixing LED flood light 210 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp complete all as specified and directed by Engineer-in-Charge.

MCB TPN 415 volts 63 Amps Capacity, 10 KA

MCB SPN of 240 volts 20/32/40 Amps Capacity, 'C' series, 10 KA

Supply & fix in replacement capacitor of capacity 2.5 mfd (PVC Body) suitable for ceiling/exhaust fans/wall mounted fans of any description,any sweep complete all as specified and directed by Engineer-in-charge.

Taking down and refixing ceiling fans/exhaust fan of any sweep any size from site for repair complete all as specified and directed by Engineer-in-charge.

EACH JOB

Material & labour for taking out & removing old burnt-out windings of Ceiling fans of any description and rewinding of fan motor with appropriate size super enameled copper wire as approved by Eng-in-charge including insulating material such as illuminous paper,Letherized paper,cotton tape,glass sleeving,insulating varnish ,Bearing ,Bushes,capacitor etc.and transportation to site after testing at workshop,connecting and testing on full load to the entire satisfaction of Eng-in-charge,including painting of fans of any description(ceiling fan/exhaust fan/wall mounte fan/pedestal fan) with applying one coat of synthetic enamel paint(white/Grey) by spray machine including preparation of exisiting decorated surfaces of fans complete all as specified and directed by Engineer-in-charge. .

Material & labour for servicing of 1200/1400MM ceiling fan by dismantling carefully and taking out unserviceable parts, dust & grease, cleaning of internal parts with kerosene oil, washing, checking of alignment of shaft, oiling and re-greasing of bearing/bushes including replacing of unserviceable part like bearing ,gun metal bush, capacitor,Rubber reel of suitable capacity and re-assembling the same and complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement of PVC body exhaust fan, AC single phase 230/240V of size 250 mm sweep with louvers including making hole of suitable size/ alteration to the existing hole to fix the Exhaust fan complete all as specified and directed by Engineer-in-charge. (Note: Old unserviceable Exhaust Fan will be deposited in MES store yard).

Supply & fix in replacement bell, AC, 230 V, SP, ding dong type complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement stepped type electronic fan Regulator flush type on the existing phenolic laminated etc as reqd single pole 240 volts grade 350 watts heavy duty ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement of Ceiling rose 3 phase, PVC/ Polycarbonate body complete all as specified and directed by Engineer-in-charge.

Supply & fix modular plastic surface box of module 1/2 flush type ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix modular plastic surface box of module 3 flush type ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix modular plastic surface box of module 4 flush type ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix modular white cover plate with frame of module 1 flush type ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix modular white cover plate with frame of module 2 flush type ISI marked complete all as specified and d

irected by Engineer-in-charge.

Supply & fix modular white cover plate with frame of module 3 flush type ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix modular white cover plate with frame of module 4 flush type ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix modular white cover plate with frame of module 6 flush type ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix modular white cover plate with frame of module 8 flush type ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix modular blank plate module 1 complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement, modular switch flush type, 6 Amp. SP, one way ,1 module complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement modular socket outlet, 3 pin, 6 Amp, flush type 2 module complete all as specified and directed by Engr-in-Charge

Supply & fix in replacement modular swicth, 16 Amp flush type 1 module complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement modular socket outlet, 3 pin, 6/16 Amp flush type 2 module complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement modular bell push, flush type, 6 Amp,1 module complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement of ceiling fan regulator modular type electronic step type 5 step 360 deg 120 watt 2 module complete all as specified and directed by Engr-in-Charge.

Material & labour for disconneting electrically and mechanically the existing geyser of any description,any capacity and make/type and in any position for repair/replacement/painting/cleaning etc including disconneting existing cold and hot water pipe connections, strip opening of geyser for descaling of tank element, thermostate,inlet/outlet water pipe connection etc using suitable chemical/wire brush,replacement of unserviceabe parts, re-assembling the same after, repair/descaling, fixing in position including, connecting inlet/outlet water pipe connection, electrical connections any testing of geyser complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement metal plug top 20Amps 3 pin complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement for PVC connection with brass nipple 15 mm x 450 mm long for geyser 25/50 ltrs capacity as per sample complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement 2.0 KW Electric heating element at site including rubber ring washers ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement of 15mm bore bib taps ISI marked cast copper alloy fancy type chroumium plated with crutch butterfly handle screw down for iro n pipe or brass ferrule complete all as specified and directed by Engineer-in-charge

Supply laying, jointing and testing cable XLPE insulated, armoured heavy duty electric cable with stranded aluminium conductor, 1100 volts grade, laid in trenches passing through pipe/ ducts/ surface of wall ceiling etc of size 240 sqmm, 3.5 core complete all as specified and directed by Engineer-in-Charge.

Supply laying, jointing and testing cable XLPE insulated, armoured heavy duty electric cable with stranded aluminium conductor, 1100 volts grade, laid in trenches passing through pipe/ ducts/ surface of wall ceiling etc of size 16 sqmm, 4.0 core complete all as specified and directed by Engineer-in-Charge.

Supply laying, jointing and testing cable XLPE insulated, armoured heavy duty electric cable with stranded aluminium conductor, 1100 volts grade, laid in trenches passing through pipe/ ducts/ surface of wall ceiling etc of size 50 sqmm, 3.5 core complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches not exc. 1.5m wide and not exc. 1.5m in depth for foundation etc or for shafts, wells, cesspits, manholes pier holes etc not exc. 10sqm on plan and not exc 1.5m in depth and getting out in hard/dense soil complete all as specified and directed by Engineer-in-Charge.

Returning filling in soil and including spreading leveling watering and well ramming in layers n.exc. 25 cm thick complete all as specified and directed by Engineer-in-Charge.

Material & labour for plain Cement concrete, type D2, (1:4:8), (using 40mm graded stone aggregate) in foundation and filling mass concrete complete all as specified and as directed by Engineer-in-Charge.

Removing excavated material soil exc 250m but n exc 500m and depositing where directed at level n.exc 1.5m above starting point complete all as specified and directed by Engineer-in-Charge

Removing excavated soil to a distance n.exc. 50 mtr and depositing where directed at a level n.exc. 1.5m above the starting points complete all as specified and directed by Engineer-in-Charge.

Supply & fix fabricating LT panel indoor type, dust and vermin proof totally enclosed with sloping canopy fabricated out of steel section the door opening shall not be less than 150 degree. The construction of panel board shall be dust vermin proof IP 54 standard double shutter gears front and rear frame work and 3.15 mm thick MS sheet duly painted with powder coated over two coats of red oxide primer and made of 40x40x6 mm thick angle iron frame all as specified suitable for 415 volts 50 Hz 3 phase and neutral system and shall be complete with 400 Amps capacity copper bus bar with bus bar chamber internal wiring with suitable size of PVC insulated copper cable lugs comprising of following accessories-: Incoming MCCB 4 pole 350 Amps 36 KA-01 Nos OUTGOING (i) MCCB 4 pole 200 Amps 36 KA-02 Nos (ii) MCCB 100 Amps 16 KA 4 pole-03 Nos Digital type Ammeter with CT 0-400-01 No Digital type Voltmeter 0-500-01 No Indicator-RYB

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in soft/ loose soil complete all as specified and as directed by Engineer-in-Charge.

Material & labour for sand cushioning for UG cables using dry river sand; gently punning down complete all as specified and directed by Engineer-in-Charge. ( Note : For measurement purpose punned thickness shall be considered)

Supply & lay ISI marked & conforming to IS - 5820 - 1970 unreinforced precast concrete cable cover Class LV, flate size 300mm X 180 mm X 40 mm in trenches as protection to LT UG cable complete all as specified and directed by Engineer-in-Charge.

Material & labour for heat shrinkable indoor/ outdoor LT end terminations for LT 1100 Volts grade, aluminum conductor including jointing kits, aluminium ferrules and labour complete for making joints and testing etc of cable size 35 to 240 Sqmm, 3.5 core complete all as specified and as directed by Eng-in-Charge.

Supply & fix copper strip 32 x 6 mm with saddles and fixing screws etc.for jointing with earth pits complete all as specified and directed by Engineer-in-charge

Supply & fix PVC clad enclosure single pole and neutral with a two pin and earth plug and socket complete with one single pole MCB of 20 Amps complete all as specified and as directed by Engineer-in-Charge.

Supply & fix in replacement modular switch 5 Amps/6 Amps flush type 1 module complete all as specified and directed by Engineer-in-Charge.

Supply & fix in replacement modular switch 5 Amps/6 Amps flush type 2 module complete all as specified and directed by Engineer-in-Charge.

Supply & fix in replacement modular switch 16 Amps flush type 1 module complete all as specified and directed by Engineer-in-Charge.

Supply & fix in replacement socket 6A/16A-2/3 pin combined 2 module complete all as specified and directed by Engineer-in-Charge.

Supply & fix in replacement modular white cover plate with frame of module 3 flush type ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement modular plastic surface box of module 3 flush type ISI marked complete all as specified and directed by Engineer-in-charge.

Material & labour for one light point/ fan point controlled by one , one way flame proof switch surface wiring complete with 1.5 sqmm single core multi stranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 volts grade drawn through ERW steel conduit heavy duty ISI marked of size 20 mm including dia accessories like tees, bends elbows, reducers bell mouth tube ends and fixing accessories such as couples, rock nuts saddles, pipe hooks etc complete all as specified and directed by Engineer-in-Charge. .

Material & labour for one light point/ fan point controlled by one , one way flame proof switch surface wiring complete with 2.5 sqmm single core multi stranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 volts grade drawn through ERW steel conduit heavy duty ISI marked of size 20 mm including dia accessories like tees, bends elbows, reducers bell mouth tube ends and fixing accessories such as couples, rock nuts saddles, pipe hooks etc complete all as specified and directed by Engineer-in-Charge. .

Supply & fixing flame proof/weather proof 4 feet LED light fitting 2x18 Watt CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum hosing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etc. Complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size etc complet

e all as specified and directed by Engineer-in-Charge.

Supply & fix flame proof/weather proof exhaust fan, 12" (300mm), single phase,with and including louvers complete CMRI certified recommended for gas group of IIA & IIB, Zone 1 & 2 and IP 65 protection with die cast aluminum hosing complete all as specified and directed by Engineer-in-Charge. Note:-The rate quoated shall be in including making holes of suitable for exhaust fan of size 300 mm dia in PCC block masonry wall, making good the side of hole with CM (1:4) on wall with two coat of paint match with existing wall and distributed surface with 4 nos of stainless steel fastner of suitable size to fit the exhaust fan no extra payment will be allowed to contractor on this regard

Supply & fix flame proof/weather proof rotary on/off switch with termination box in LM6, 16A, 2 pole 250V complete all as specified and directed by Engineer-in-charge.

Supply & fix flame proof/weather proofswitch socket & plug combined in LM6, cable termnation box in LM6, 16A, 250V, 2P+earth complete all as specified and directed by Engineer-in-charge.

Material & labour for sub main wiring with two runs of PVC insulated and unsheathed FRLSH cable 650/1100 Volts grade, conforming to IS-1536-1977 multi-stranded 4 Sqmm single core, copper conductor drawn through and including conduit medium grade/new casing capping ISI marked with accessories and 4 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 volts grade, ISI marked as earth continuity wire complete all as specified and directed by Engr-in-Charge. (Note: Three runs of conductor for phase with one run of neutral and one run for earth wire and PVC conduit/casing capping will be measured & paid as one unit)

Supply & fix single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 10 Amps, 240 v complete all as specified and directed by Engineer-in-Charge.

Supply laying, jointing and testing cable XLPE insulated, armoured heavy duty electric cable with stranded aluminium conductor, 1100 volts grade, laid in trenches passing through pipe/ ducts/ surface of wall ceiling etc of size 10 sqmm, 2.0 core complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches not exc. 1.5m wide and not exc. 1.5m in depth for foundation etc or for shafts, wells, cesspits, manholes pier holes etc not exc. 10sqm on plan and not exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed by Engineer-in-Charge.

Supply & fix glavanised medium class pipe including fittings of dia 80 mm (3") dia complete all as specified and directed by Engineer-in-charge.

Material & labour for cutting the existing GI/DI pipe of size 80 mm dia and taking 80 mm dia branch connection including necessary fittings etc complete all as specified and directed by Engineer-in-Charge.

MCB SP of 240 volts 6-32 Amps Capacity, 'C' series, 10 KA

Material & labour for precast cement concrete block masonry type 1:3:6 using 20mm graded stone aggregate with solid blocks, exc 10cm in width and setting in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

Supply & fix TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia complete all as specified and directed by Engineer-in-Charge.

Material & labour for precast reinforced cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, shelves and similar articles with plain faces, set in CM 1:4, including necessary form work moulds etc complete all as specified and directed by Engineer-in-Charge. (Reinforcement shall be measured and paid for separately).

Material & labour for 50 mm thick cement concrete type B-1,1:2:4 mix (using 20 mm graded stone aggregates) as in copings including necessary use and waste of form work complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparing new plastered surfaces of walls and applying two Coats of acrylic washable distemper over a coat of chalk whitening complete all as specified and directed by Engineer-in-Charge.

Supply & fix anodised aluminium frame for doors, windows, ventilators and fixed partitions with one or more rebates including joining cleat for fixing etc complete all as specified and directed by Engineer-in-Charge

Supply & fix anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc complete all as specified and directed by Engineer-in-Charge.

Material & labour for 4.00 mm thick sheet glass ordinary quality and glazing with oil putty in square exc 0.50 Sqm in each pane complete all as specified and directed by Engineer-in-charge.

Material & labour for prelaminated particle board 9mm thick interior grade prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws to timber frame work fixed for cuboards/shelfs etc complete all as specified and directed by Engineer-in-charge.

Material & labour for PCC 1:2:4, B2 ( using 40mm graded stone aggregate) in foundations filling and mass concrete complete all as specified and directed by Engineer-in-Charge.

Supply & fix mild steel pipe (tubular) fixed as vertical post including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S. 1161-1979 grade St.-240 as in posts complete all as specified and as directed by Engineer-in-Charge.

Supply & fix steel work as rafters and web in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S. 1161-1979 grade St.-240 complete all as specified and directed by Engineer-in-Charge.

Supply & fix mild steel plates, plain or chequered, in Fe 410-W (Gde-E- 250) quality-A complete all as specified and directed by Engineer-in-Charge.

Supply & fix mild steel screw bolts 16 to 20 mm dia of neck (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm long and n exc 10 cm long complete all as specified and directed by Engineer-in-Charge.

Supply & fix pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550MPA as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

Supply & fix pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550MPA as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.