Construction of New 4 Nos. C Type Category Quarter for PHC Bela, Taluka Rapar, Kutch

Name of work: Construction of New 4 Nos. C Type Category Quarter for PHC

Bela, Taluka Rapar, Kutch

BILL OF QUANTITIES

Item No. Item Description Quantities Unit Amount

Excavation for foundation upto 1.5 m depth including

sorting out and stacking of useful materials and

disposing off the excavated stuff as directed upto

Meter lead (B) Dense or hard soil

Excavation for foundation for depth from 1.5 m to 3.0 m

including sorting out and stacking of useful materials and

disposing off the excavated stuff as directed upto

Meter lead. (B) Dense or hard Soil

Applying general insecticide pest control treatment to

floors, cupboards etc including labour material etc.

complete. Using Imidacloprid 30.5Sc As Per IS

3 part‐ II (0.075% cocentration by mass) is recommended 246.23 Sqm 91.63

10.5ml chemical dillute with 5 liter of water appication

Litre chemical / Sqm of surface is recommended as per

Providing & laying controlled cement concrete M150 for

curing complete including cost of form work but

excluding cost of reinforcement for reinforced conrete

work in foundation and plinth.

Providing and laying Controlled cement concrete M250

and curing complete including the cost of formwork but

5 excluding the cost of reinforcement for RCC work. (a) 53.63 Cum 4654.67

Foundation, Footing base of column mass concrete. For

Column Footing.

Providing & Laying controlled cement concrete M250

and curing complete including cost of formwork but

excluding the cost of reinforcement for reinforced

concrete work in Grade Slab.

Compaction and finishing of cement concrete road by

tremix process, providing extra labour charge for tremix

(Vaccum dewatering service) process on cement

concrete road surface by using vaccum dewatering

7 pump floater surface vibrator including making groove 448.64 Sqm 71.21

5mm width and filling with polyvynile polymer and rough

finish to surface as per instruction including leveling etc

Providing and laying Controlled cement concrete M250

and curing complete including the cost of form work but

excluding the cost of reinforcement for RCC work (B)

Filling available excavated earth excluding rock in

trenches plinth side of foundation etc in layer not

exceeding 20 cm in depth consolidation each deposit

layer by ramming and watering.

Filling in plinth with sand under floors including watering,

10 ramming, consolidating and dressing etc complete as 23.03 Cum 481.80

directed by Engineer in charge.

Providing and laying Controlled cement concrete M250

and curing complete including the cost of form work but

excluding the cost of reinforcement for RCC work for GF

(C) Column for Hollow Plinth/Parking.

Providing and laying Controlled cement concrete M250

and curing etc. complete including the cost of form work

12 but excluding the cost of reinforcement for RCC work for 21.42 Cum 5938.40

GF (B) Beam for Hollow Plinth/Parking.(GF Slab Lvl)

Item No. Item Description Quantities Unit Amount

Providing and laying Controlled cement concrete M250

and curing complete including the cost of form work but

excluding the cost of reinforcement for RCC work GF (B)

Slab for hollow plinth/Parking (GF Slab lvl).

Providing and laying Controlled cement concrete M250

and curing complete including the cost of form work but

excluding the cost of reinforcement for RCC work (C)

Providing and laying Controlled cement concrete M250

and curing etc. complete including the cost of form work

but excluding the cost of reinforcement for RCC work (B)

Beam for FF (SF slab lvl).

Providing and laying Controlled cement concrete M250

and curing complete including the cost of form work but

excluding the cost of reinforcement for RCC work (B)

Slab for FF (SF slab lvl).

Provinding and Laying controlled cement concrete M250

including finishing smooth and curing etc.complete

17 including the cost of formwork but excluding the cost of 3.45 Cum 8284.99

reinforcement for R.C.C work in Lintel for FF.

Providing and laying controlled cement concrete M250

upto floor two level and curing complete including

18 finishing with a floating coat of neat cement slurry the 0.92 Cum 7533.89

cost of form work but excluding the cost of reinforcement

for RCC work in Chajjas For FF.

Providing and laying Controlled cement concrete M250

and curing complete including the cost of form work but

excluding the cost of reinforcement for RCC work (C)

Providing and laying Controlled cement concrete M250

and curing etc. complete including the cost of form work

but excluding the cost of reinforcement for RCC work (B)

Beam for SF (SF Slab lvl).

Providing and laying Controlled cement concrete M250

and curing complete including the cost of form work but

excluding the cost of reinforcement for RCC work (B)

Slab for SF(SF Slab lvl).

Provinding and Laying controlled cement concrete M250

including finishing smooth and curing etc.complete

22 including the cost of formwork but excluding the cost of 3.45 Cum 8325.93

reinforcement for R.C.C work in Lintel for SF.

Providing and laying controlled cement concrete M250

upto floor two level and curing complete including

23 finishing with a floating coat of neat cement slurry the 0.92 Cum 7574.83

cost of form work but excluding the cost of reinforcement

for RCC work in Chajjas For SF.

Providing and laying Controlled cement concrete M250

and curing complete including the cost of form work but

excluding the cost of reinforcement for RCC work in

column for TF (C) Column for Stair cabin

Providing and laying Controlled cement concrete M250

and curing etc. complete including the cost of form work

but excluding the cost of reinforcement for RCC work in

beam for TF (B) Beam for TF Stair cabin.

Providing and laying Controlled cement concrete M250

and curing complete including the cost of form work but

excluding the cost of reinforcement for RCC work in slab

for TF (B) Slab for TF (Stair cabin Slab lvl).

Providing and laying controlled cement concrete M250

upto floor two level and curing complete including

27 finishing with a floating coat of neat cement slurry the 0.14 Cum 7615.76

cost of form work but excluding the cost of reinforcement

for RCC work in Chajjas For Stair Cabin.

Item No. Item Description Quantities Unit Amount

Providing and fixingTMT FE 500 D Anchor/Rebaring

bars of minimum 12 mm dia, length of bar 300 mm for

anchoring by drilling holes minimum 100 mm deep in

28 existing RCC/Masonary Work, including properly placing 290.00 Nos 25.25

of bars and grouting the holes with sealing with appoxy

material finishing the same etc complete as directed by

Engineer incharge.

Providing and laying controlled cement concrete M250

and curing complete including the cost of formwork and

excluding the cost of reinforcement for reinforced

concrete work in (E) Staircase for All floor

Providing ISI mark TMT bar FE 500D reinforcement for

30 R.C.C work including bending, binding and placing in 26643.48 Kg 77.29

position etc complete upto All Floor Level.

Brick work using common burnt clay building bricks

having crushing strength not less than 35 Kg./Sq.Cm. in

foundation and plinth in cement mortar 1:5 ( 1-cement : 5-

fine sand ) (B) Conventional For upto Plinth.

Brick work using common burnt clay building bricks

having crushing strength not less than 35 Kg./Sq.Cm. in

32 foundation and plinth in cement mortar 1:5 ( 1-cement : 5- 10.64 Cum 4526.81

fine sand ) (B) Conventional For Ground Floor / Hollow

Plinth / Parking.

Brick work using common burnt clay building bricks

having crushing strength not less than 35 Kg./Sq.Cm. in

33 cement mortar 1:5 ( 1-cement : 5-fine sand ) in super 52.57 Cum 4850.96

structure above plinth level upto floor two level. (B)

Conventional For First Floor

Brick work using common burnt clay building bricks

having crushing strength not less than 35 Kg./Sq.Cm. in

34 cement mortar 1:5 ( 1-cement : 5-fine sand ) in super 52.57 Cum 4893.39

structure above plinth level upto floor two level. (B)

Conventional For Second Floor

Brick work using common burnt clay building bricks

having crushing strength not less than 35 Kg./Sq.Cm. in

35 cement mortar 1:5 ( 1-cement : 5-fine sand ) in super 19.08 Cum 4935.82

structure above plinth level upto floor two level. (B)

Conventional For Terrace Floor

Half brick masonary in common burnt clay building bricks

having crushing strength not less than 35kg/sq.cm. in

cement mortar 1:3 (1-cement : 3-coarse sand ) with

36 Nos of 8mm TMT steel round bars after every three 56.89 Sqm 811.49

course embedded in Cement Mortar in superstructure

above plinth level. (B) Conventional (For FF)

Half brick masonary in common burnt clay building bricks

having crushing strength not less than 35kg/sq.cm. in

cement mortar 1:3 (1-cement : 3-coarse sand ) with

37 Nos of 8mm TMT steel round bars after every three 56.89 Sqm 817.80

course embedded in Cement Mortar in superstructure

above plinth level. (B) Conventional (For SF)

Half brick masonary in common burnt clay building bricks

having crushing strength not less than 35kg/sq.cm. in

cement mortar 1:3 (1-cement : 3-coarse sand ) with

38 Nos of 8mm TMT steel round bars after every three 9.95 Sqm 824.10

course embedded in Cement Mortar in superstructure

above plinth level. (B) Conventional (For Terrace Floor)

Item No. Item Description Quantities Unit Amount

Providing and fixing side hunge Single shutter Door

including using Anodized Aluminium Section domel

series frame having zindal Door Section no.

weight not less than 1.1 Kg/mt, 35 mm thick and pannel

of both side Pre laminated Water Boiling Proof Plywood

39 particle board 12 mm thick of natural wood grain shed, 49.98 Sqm 4464.23

1mm thick laminated with fixing of 2x3 cm T.W. moulding

on both side, fixing of 5 mm thick tranparent glass in top

ventilator as per detail drawing including three coat of oil

paint with primer etc complete as per instruction of

Engineer in charge & approved make. Door D1, D2

Providing and Fixing of 100 X 50 mm thick FRP frame

with 35mm thick FRP shutter with 1.5 to 2.0 mm thick

fire retardent grade FRP skin in wood grain rasied panel

design having extra reinforcement on sides & edges

& in polish design finish. The core of the shutter is to

be filled up with injected retardent grade

40 polyurethane foam done in situ alongwith embedded 13.44 Sqm 986.39

wooden pieces for stiffening & also taking hinges &

fixtures. The whole shutter is to be water proof,

weather proof, termite proof & resistance to mild

acid/alkali. Rates are to be inclusive of S.S hinges with

necessary screws & alluminium S.S finish fixtures &

fastenings as per instruction of Engineer in charge &

approved make. Door - D3

Providing and fixing window having extruded aluminum

Colour anodized section frame main outer size 95mm x

24mm x 1.17mm @ wt.of 0.738 Kg/mt , horizontal Three

track member size 92mm x 31.75mm x 1.30mm,@

Wt.1.07 Kg/mt , vertical member of size 92mm x

31.75mm x 1.50mm @ Wt. 1.06 Kg/mt with sliding

shutters of horizontal member size 40 mmx18mm

41 x1.29mm @ wt.of 0.456 Kg/mt, vertical member of size 27.84 Sqm 1990.48

40mm x 18mm x 1.29 mm @ wt.of 0.456Kg/mt/ with

mm thick transparent bronze colour tinted float glass with

SS 304 Mosquito net with powder coated aluminum

fittings and fixtures and transparent silicon sealant glass

fixing to frame as per details etc complete as directed by

Engineer Incharge for Window-W1

Providing and fixing window having extruded aluminum

Colour anodized section frame main outer size 63.50 x

38.10 x 1.95 mm,@ Wt 1.094 Kg / Rmt, horizontal Two

track member size 61.85 mm x 31.75 mm x 1.20mm @

wt.of 0.695 Kg/mt, vertical member of size 61.85 mm x

31.75mm x 1.30 mm @ wt.of 0.659 Kg/mt with sliding

42 shutters of horizontal member size 40mm x 18mm x 3.80 Sqm 2120.22

1.29mm @ wt.of 0.456Kg/mt, vertical member of size

0.457 Kg/mt with 5 mm thick transparent bronze colour

tinted float glass with powder coated aluminum fittings

and fixtures and transparent silicon sealant glass fixing

to frame as per details etc complete for window. Window-

Providing and fixing S.S. 316 mosquito net jali fixing in

Aluminium section of size 62.5 X 62.5 X 1.25 mm of

43 Square pipe using angle section for fixing of S.S. Jali 2.88 Sqm 3825.54

With Rubber Gasket/Patti as directed by Engineer in

charge. Ventilation - V

Item No. Item Description Quantities Unit Amount

Providing and fixing M.S. grills/ Railing of required

pattern to M.S. frames of windows ,Door , Jali etc.

with M.S. flats at required spacings and frame alround,

44 square or round Bright bars of 16mm dia, with round 890.09 Kg 123.14

headed bolts and nuts or by screws including One

coat of primer and two coat of oil paints, all Fixture etc

complete as directed by Engineer in charge.

Providing and fixing MS pipe of 50 mm dia, wall

thicness 3.20 mm and weight 4.20 per Rmt including,

45 cutting, bending, binding, welding, grinding of pipe, end 37.20 Rmt 1082.07

covering with same material fixing in masonary work,

finishing the same etc complete as directed by Engineer

Providing 20 mm thick Double coat mala cement plaster

on interior brick / concrete work for plastering comprising

of base coat of 12 mm thick cement plaster in cement

mortar (1 Cement : 4 coarse sand) in rough finishing and

46 8 mm thick top coat of cement mortar 1:2 (1 Cement : 2 403.70 Sqm 265.65

Coarse sand) finished with trovel including with mixing of

waterproofing material scaffolding curing, 10x10 mm

Joints grooves etc. complete for All Floors with. For GF

Providing 20 mm thick Double coat mala cement plaster

on interior brick / concrete work for plastering comprising

of base coat of 12 mm thick cement plaster in cement

mortar (1 Cement : 4 coarse sand) in rough finishing and

47 8 mm thick top coat of cement mortar 1:2 (1 Cement : 2 524.53 Sqm 297.74

Coarse sand) finished with trovel including with mixing of

waterproofing material scaffolding curing, 10x10 mm

Joints grooves etc. complete for All Floors with. For First

Providing 20 mm thick Double coat mala cement plaster

on interior brick / concrete work for plastering comprising

of base coat of 12 mm thick cement plaster in cement

mortar (1 Cement : 4 coarse sand) in rough finishing and

48 8 mm thick top coat of cement mortar 1:2 (1 Cement : 2 524.53 Sqm 329.82

Coarse sand) finished with trovel including with mixing of

waterproofing material scaffolding curing, 10x10 mm

Joints grooves etc. complete for All Floors with. For

Providing 20 mm thick Double coat mala cement plaster

on interior brick / concrete work for plastering comprising

of base coat of 12 mm thick cement plaster in cement

mortar (1 Cement : 4 coarse sand) in rough finishing and

49 8 mm thick top coat of cement mortar 1:2 (1 Cement : 2 133.33 Sqm 361.91

Coarse sand) finished with trovel including with mixing of

waterproofing material scaffolding curing, 10x10 mm

Joints grooves etc. complete for All Floors with. For

Providing 10mm thick cement plaster in single coat on

AAC Block/concrete walls for interior plastering upto

floor two level and finished even and smooth in (i)

50 Cement mortar 1:3 (1-cement:3-sand) including finishing 234.73 Sqm 135.47

etc complete as directed by Engineer in charge. Ceiling

Plaster For Ground Floor slab/Hollow Plinth/Parking.

Providing 10mm thick cement plaster in single coat on

AAC Block/concrete walls for interior plastering upto

51 floor two level and finished even and smooth in (i) 116.06 Sqm 161.53

Cement mortar 1:3 (1-cement:3-sand) including finishing

etc complete as directed by Engineer in charge. Ceiling

Plaster For First Floor

Item No. Item Description Quantities Unit Amount

Providing 10mm thick cement plaster in single coat on

AAC Block/concrete walls for interior plastering upto

52 floor two level and finished even and smooth in (i) 116.06 Sqm 187.59

Cement mortar 1:3 (1-cement:3-sand) including finishing

etc complete as directed by Engineer in charge. Ceiling

Plaster For Second Floor

Providing 10mm thick cement plaster in single coat on

AAC Block/concrete walls for interior plastering upto

53 floor two level and finished even and smooth in (i) 19.22 Sqm 213.65

Cement mortar 1:3 (1-cement:3-sand) including finishing

etc complete as directed by Engineer in charge. Ceiling

Plaster For Terrace Floor

Providing 20 mm thick Sand Faced Gutka Finish cement

plaster on wall up to all height above ground level

54 consisting of 12 mm thick backing coat of C.M. 1 : 3 (1 629.72 Sqm 315.69

cement : 3 sand) and 8 mm thick finishing coat of C.M.

: 1 (1 cement : 1 sand) complete with all lead & Lift as

directed by Engineer incharge.

Applying two coats plastic emulsion paint acrylic laphy

(putty) & two coat of primer of approved brand and

manufacture on new wall surface to give an even shade

55 including thoroughly brushing the surface free from 1961.94 Sqm 124.96

mortar dropping and other foreign matter and sand

papered smooth as per instruction of Engineer in charge

& approved make.

Wall Painting three coats with weather proof acralic

exterior emulsion paint of approved brand and

manufacture and of required shade on exterior wall

surface to give an evev shade over and including a

56 primary coat with alkaly resistance primer of approved 629.72 Sqm 162.81

brand after throughly brushing the surface to remove all

dirt and remain of loose powdered materials etc

complete for all height as per instruction of Engineer in

charge & approved make.

Providing and laying Black Machine Cut free edges,

Machine polished Granite Stone slab 18 mm thick

single piece For Stair, Step, Landing, Skirting etc as per

design including fully moulded round front edge and 1cm

57 nosing and necessary V- groove on trade of steps laid 138.05 Sqm 3025.61

on 20 mm thick cement mortar 1:6 (1-cement : 6 coarse

sand) jointed with grey cement slurry including rubbing,

polishing & Finishing etc complete as directed by

Enginner in Charge. F1

Providing and laying 60 X 60 cm Glossy finish full body

Granite Vitrified 10 mm thick Tiles Flooring over 20 mm

58 (avg) thick base of cement mortar 1:6 (1-cement : 6- 183.34 Sqm 1892.49

coarse sand) jointed with white cement with colour

pigment, finish the same etc coimplete as directed by

Engineer incharge. F2

Providing and laying 60 X 60 cm Glossy finish full body

Granite Vitrified 10 mm thick Tiles Skirting over 20 mm

59 (avg) thick base of cement mortar 1:6 (1-cement : 6- 23.83 Sqm 1853.68

coarse sand) jointed with white cement with colour

pigment, finish the same etc coimplete as directed by

Engineer incharge. F3

Providing and laying polished Kota stone slab flooring

over 20mm (Average) thick base of cement mortar 1:6 (1-

cement : 6-coarse sand) laid over and jointed with grey

60 cement slurry mixed with pigment to match the shade of 48.01 Sqm 1013.87

slab including rubbing and mirror polishing etc. complete.

(A) 25mm thick. F4

Item No. Item Description Quantities Unit Amount

Providing and laying coloured glazed tiles Matt finish

of the size 300 mm x 300 mm x 8 mm in skirting, risers

61 of steps and dedo on 10 mm. thick cement plaster 1:3 13.54 Sqm 1488.24

(1 cement : 3 coarse sand) & jointed with white cement

Providing and laying coloured glazed tiles of the

size 300 mm x 600 mm x 8 mm in skirting, risers of

62 steps and dedo on 10 mm. thick cement plaster 1:3 (1 86.90 Sqm 1562.65

cement : 3 coarse sand) & jointed with white cement

slurry. F6 for Dedo

Providing and laying broken china mosaic flooring for

terrace using 12 mm to 20 mm broken pieces of Water

Proofing glazed tiles to be laid over cement mortar 1:3 to

63 plain or slope and to be tempered to bring mortar creme 151.34 Sqm 779.70

out upto surface using white cement including rounding

off junctions and extending them upto 15 cm along

the wall,clearing with water and oxalic acid etc. as

directed by Engineer in charged. F7

Providing and fixing SS 316 Grade 90 cm high Stainless

steel railing made from anticorrosive SS pipe of 50 mm

dia (16Gauge) as hand rail with SS 38 mm dia

64 (16Gauge) as a vertical support fixed in RCC slab at 11.95 Rmt 2426.87

1.2m c/c including three horizontal SS pipes of 25 mm

dia (16Gauge) at equal distance fixed by 18.75 mm dia

(16Gauge) S S pipe including accessories as per

detailed drawing as directed etc complete.

Provision and fixing water closet squatting Orissa type

W.C. pan size 580mm integral footrest and 100 mm P

65 or S trap and in cluding 25 mm dia CP brass flush valve 4.00 Nos 1142.10

and GI inlet connection etc. comp. (A) Vitreous china

long pattern white or color including GI Inlet connection

for flush pipe with WC pan.

Providing & Fixing PVC SWR Nanhi trap IS 14735 for

drain 75mm with jali of the following nominal diameter of

66 self cleansing design with C.I. Screwed down or hinged 12.00 Nos 574.58

gratting including cost of cutting and making good the

Providing & Fixing S.W. Gully trap with C.I. Greating

brick masonay chamber and water tight C..I Cover with

67 frame of 300 mm X 300 mm Size ( Indian ) with standard 4.00 Nos 1246.92

weight (i) Square mouth traps (C) 150 mm x100 mm size

Constructing brick masonary chamber for underground

C.I. Inspection chamber and bends with bricks having

crushing strenght not less than 35kg/ cm2 in C.M. 1:5

C.I. Cover with frame ( light duty) 455mm x 610mm

internal dimention total weight of cover with frame to be

not less than 38Kgs (weight of cover 23kg and weight of

68 frame 15Kg). R.C.C. tpp slab with 1:2:4 (1 cement : 2 2.00 Nos 2932.93

coarse sand : 4 graded stone aggregate 10mm nominal

size) foundation concrete 1:5:10 inside plaster 1:3

finished smooth with a floting cost of neat cement on

walls and bed concrete etc. comp. (i) inside dimension

455mm x 610mm & 450mm deep for single pipe

Item No. Item Description Quantities Unit Amount

Constructing brick masonry chamber for underground

C.I. Inspection chamber and bends with briocks having

croshing strength not less than 35Kg. Cm2 in C.M. 1:5

C.I. cover with frame (Light duty) 455mm x 610mm

intenal dimensions total weight of cover with frame to be

not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of

69 frame 15Kg.) (R.C.C. top slabe with 1:2:4 mix (1-cement 5.00 Nos 3660.76

:2- coarse sand :4-graded stone aggregate 20mm size)

foundation concrete 1:5:10 inside plaster 15mm thick

with cement mortar 1:3 finished smooth with a floating

coat of neat cement on walls and bed concrete etc.

complete.(i) Inside dimensions 500mmx 700mm and

450mm deep for pipe line with one or more inlet.

Providing laying and jointing in true line and level UPVC

SWR pipe Type B pipe confirming to IS 13592 -1992

with one end plain and other end socketed with

rubbering & fitting confirming to ISI 14735-1999 of

approved make for drainage system pipe line,pipe shall

be jointed with each other with rubber lubricant,pipe shall

70 be fixed on wall using of PVC clamp of the size 160mm 45.00 Rmt 712.44

diameter x 210mm lenght x 196mm high at every

2000mm center to center or shall be concealed in wall as

directed including necessary fitting such as bends,shoes

etc. including testing of pipe and joints and jointed with

adhesive solvent cement including cost of all materials.

Providing laying and jointing in true line and level UPVC

SWR pipe Type B pipe confirming to IS 13592 -1992

with one end plain and other end socketed with

rubbering & fitting confirming to ISI 14735-1999 of

approved make for drainage system pipe line,pipe shall

be jointed with each other with rubber lubricant,pipe shall

71 be fixed on wall using of PVC clamp of the size 160mm 204.00 Rmt 876.90

diameter x 210mm lenght x 196mm high at every

2000mm center to center or shall be concealed in wall as

directed including necessary fitting such as bends,shoes

etc. including testing of pipe and joints and jointed with

adhesive solvent cement including cost of all materials.

(ii) 110 mm Dia

Providing & Fixing G.I. Z Type heavy duty clamps with

G.I. 6 mm dia. ring for sutiable dia of pipe for Rain

72 Water, Drainage, Water Supply line including drilling 80.00 Nos 80.80

holes, fixing of pipe, nuts, bolts, washers with all lead &

lift etc complete as directd by Engineer in charge.

Providing and fixing in position cowel went to pipes. (B)

Providing and fixing in position cowel went to pipes. (C)

Providing and laying in true line and level U.P.V.C (Sch-

40) including fitting as approved by Engineer in charge.

Pipe shall be fixed on the wall with held of clamp at every

75 two meter c/c shall be concealed or open as directed 20.00 Rmt 195.67

including necessary fitting etc. including testing of pipe

and joints and fixing the same with adhesive solvent

including cost of all materials. (iii) 50 mm dia.

Providing and laying in true line and level U.P.V.C (Sch-

40) including fitting as approved by Engineer in charge.

Pipe shall be fixed on the wall with held of clamp at every

76 two meter c/c shall be concealed or open as directed 60.00 Rmt 148.12

including necessary fitting etc. including testing of pipe

and joints and fixing the same with adhesive solvent

including cost of all materials. (iii) 40 mm dia.

Item No. Item Description Quantities Unit Amount

Providing and laying in true line and level U.P.V.C (Sch-

40) including fitting as approved by Engineer in charge.

Pipe shall be fixed on the wall with held of clamp at every

77 two meter c/c shall be concealed or open as directed 60.00 Rmt 91.84

including necessary fitting etc. including testing of pipe

and joints and fixing the same with adhesive solvent

including cost of all materials. (ii) 25 mm dia.

Providing and laying in true line and level U.P.V.C (Sch-

40) including fitting as approved by Engineer in charge.

Pipe shall be fixed on the wall with held of clamp at every

78 two meter c/c shall be concealed or open as directed 40.00 Rmt 72.65

including necessary fitting etc. including testing of pipe

and joints and fixing the same with adhesive solvent

including cost of all materials. (ii) 15 mm dia.

Providing and laying (to level or slopes) and jointing with

stiff mixture of Cement Mortar in proportion 1:1 Selt

79 glazed stoneware pipes including cement Concrete 1: 5: 30.00 Rmt 352.73

10 bedding testing of pipes and joints complete. (A)

100mm dia. (112 mm avg. thick bed)

Providing & Fixing gun metal check or non return full way

wheel valve etc. comp.(E) 40 mm dia

Providing & Fixing gun metal check or non return full way

wheel valve etc. comp.(c) 25 mm dia

Providing & Fixing CP brass screw down half turn stop

82 cock of approved quality of 15mm dia.size with 16.00 Nos 205.83

adjustable wall flange.

Providing and fixing 600mm x 120mm glass shelf with

83 C.P. brass bracket and guard rail complete mixed to 8.00 Nos 544.51

wooden plug with C.P. brass screws.

Providing & Fixing C.P. brass towel rail complete with

84 C.P. brass brackets fixed to wodden plug with C.P. brass 4.00 Nos 616.42

screws (B) 60mm x 20mm size

Providng and fixing 600mm x 450mm bevelled edge

mirror or decorative of superior glass mounted on 6mm

thick A.C. sheet or plywood plug with C.P. brass

screw and washer.

Providng and filling screened of Brick Bats / Chhara

including consolidation etc complete.

Providing erecting and fixing double coated Syntex

HDPE PVC (ISI) water tank of required capacity each

with all necessary fittings and connection etc. complete

with all lead and lift on terrace.

Providing and fixing ball cock of approved quality as

directed (A) Copper metal (i) 25mm dia.

Providing and fixing in position 300 to 150mm wide

English / Gujarati letters made from 1.0mm thick

89 stainless steel sheet as directed by Engineer in charge 10.00 Nos 757.50

with all material, hardware, accessories and fitting etc

Providing & Fixing SS 316 Silver Chicken Wire Mesh,

Hexagonal Wiremesh jali of 20 gauge at junction of the

90 brick masonary and reinforced cement concrete member 55.64 Sqm 49.49

including fixing of required materials,scaffolding, labour

etc complete as directed by Engineer incharge.

Item No. Item Description Quantities Unit Amount

Providing, Laying and Interloacking

100mm/150mm/200mm Masonary work using Aerated

light weight concrete block (AAC) having crushing

strength not less than 35 kg/sqcm for Foundation and

91 upto plinth level, using Ready Mix bonding material as a 44.58 Cum 5465.43

best and approved quality of adhesive mortar suitable

with layer of 4 mm thick laying with using of thread towel

tools, finishing joint, surface, reuire scafolding etc

complete by Engineer Incharge.

Providing & laying controlled cement concrete M250 for

curing complete including cost of form work but

excluding cost of reinforcement for reinforced conrete

work in fins/wall for all floor.

Providing and laying Controlled cement concrete M-250

and curing complete including the cost of form work but

93 excluding the cost of reinforcement for reinforced 0.93 Cum 5298.36

concrete work in Wall caps / Coping.

Providing and fixing M.S. grills / Gates of required

pattern to brick walls / Columns prepared with M.S. flats,

angles, Square / round bars, square pipes, at required

spacings with necessary hold fasts as per detailed

94 drawingand fixing brick wall / coping / columns etc. 504.00 kg 162.86

complete including painting two coat & applying primer

(A) Ornamental Grill

Providing & fixing Razor coil wire fencing having

diameter of 0.75 mt including using of M.S angle

45x45x6mm as per detail drawing, fixing in cement

95 concrete M-250 etc completed with one coat of primer & 24.00 Rmt 808.00

two coats of oil paint to M.S angle, including concrete

cutting in existing compound wall with breaker, fixing of

MS angle etc. complete as directed by Engineer in

Clearing and grubbing road land including uprooting rank

vegetation grass bushes,shrubs,sapling and trees girth

96 up to 300 mm removal of stumps of trees cut earlier and 0.11 Hec 28455.03

disposal of unserviceable materials (C) By mechanical

means in area of light jungle.

Earthwork for embankment including breaking clods,

dressing with all lead and lift (excluding watering and

consolidation)(E) From Borrow area within 3.0 Km. lead

Rolling of earthwork in layers with power roller including

filling in depressions which occur during the process

including Watering of earth work as directed by Engineer

Box cutting the road surface to proper slope and camber

for making a base for road work including removing the

excavated stuff with desposing on the road side slope as

directed up to 50 mt. Lead

Providing and and laying controlled cement concrete

M250 and curing etc complete including the cost of form

work but excluding the cost of reinforcement for R.C.C.

work for internal road etc copmlete.

Excavation for foundation for depth from 3.0 m to 5.0 m

including sorting out and stacking of useful materials and

disposing off the excavated stuff as directed upto

Meter lead.(C) Hard Murrum

Providing and laying cement concrete flooring M150 laid

in one layer and finished with a floating coat of neat

(B) 50mm thick. (upto 10 ton)

Item No. Item Description Quantities Unit Amount

Providing cement vata (10cm x 10cm size) quarter

round in cement mortar 1:1 including neat cement

finishing, watering etc complete as directed by Engineer

Providing and fixing Fiber Reinforcemen Concrete (FRC)

Manhole cover of heavy Duty of load capacity upto

104 Tons including frame etc complete as directed by 6.00 No 2525.00

Engineer incharge.

Size: 0.60m x 0.60m

Providing and fixing cast iron steps of size 500mm

105 x 150mm x 22.5mm and painting with two coats of Anti- 24.00 No 207.66

corrosive paint etc complete.

Constructing Manhole with R.C.C. top slab in 1:2:4 mix

(1-cement :2-coarse sand : 4-graded stone

aggregate 20mm nominal size) foundation concrete

1:3:6 mix (1- cement : 3- coarse sand :6-Brick bats 40 +

50mm size) inside plastering 15mm thick with Cement

Mortar 1:5 (1-Cement : 5-coarse sand) finished with

a floating coat of neat cement and making channels

in cement concrete 1:2:4 mix (1-Cement :2-Coarse sand

:4-stone aggregate 20mm nominal size) finished

106 smooth complete including curing and festing (i) 2.00 No 23470.48

Inside size 900mm x 1200mm and 1.5M. deep including

C.I. cover with frame size 560mm diameter total weight

of cover and frame to be not less than 128 kgs. (Wt. of

cover 64 Kg. and Wt. of frame 64 Kg.)(A) With

230mm thick walls of brick msonry using brick

having crushing strength not less than 35Kg. /

Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse

sand) (3) C type depth 2.25 Metre for 150mm

diameter sewer.

Providing and laying Cement concrete M150 bedding for

stoneware pipes of following internal diameters with

necessary formwork and curing complete.

(A) 100 mm dia. (112 mm Ave. bed thickness)

Providing & laying controlled cement concrete M250 and

curing complete including the cost of fromwork and

excluding the cost of reinforcement for reinforced

concrete work in Wall/Shear Wall.

Providing and laying Water proof white glazed tiles

mm. Thick in flooring treads of steps and landings laid on

109 a Bed of 12 mm. Thick cement mortar 1:3 (1 cement : 3 50.67 Sqm 963.12

coarse sand) finished with flush pointing in white cement

Providing and laying cement concrete flooring M150 laid

in one layer and finished with a floating coat of neat

110 cement with mixing water proofing material in Cement 34.30 Sqm 301.67

concrete in mix proportion recommended by the

manufacturers. (A) 40mm thick.

Providing and fixing the P.V.C. rain water out let pipe of

I.S.I. Mark as per instruction of Engineer in charge &

approved make with necessary bend, plug, jali, clamps

etc complete. 110 mm dia.

Drilling of 250 mm dia. bore well in all strata including

dual over burden strata by Combination DR / DTH rig

including lowering 200 mm dia MS ERW pipes in bore

hole as suggested by Hydrologist.

Item No. Item Description Quantities Unit Amount

Drilling of 300 / 315mmdia. bore in all strata including

dual over burden strata by combination DR/DTH rig

including lowering of 204mm dia UPVC/225/250mm

dia.PVC/MSERWcasingpipesup 200 mm /225/250mm

113 dia.PVC/MS ERW casing pipes up to required depth and 300.00 Rmt 549.44

further drilling of 200mm dia. bore hole in all types of

Alluvial Rocky strata formation by DTH ring including

flush in bore hole by air compressor and measuring of

yield of bore by V notch and fixing of bore cap etc.

Supply of clay ball of size ranging from 25 mm to 50 mm

114 made from stickly clay at site of work as certified by 40.00 Cum 758.51

supply and delivery of ISI marked ERW MS pipes

115 conforming to IS: 4270/2001 with latest amendment 40.00 Rmt 2431.07

(a) 200 mm dia. (Minimum 6.00 mm thick)

Supply of 200mm dia & 6 mm thick ERW slotted pipe

having stainer size 100 mm X 4 mm.

Providing and Jointing ERW blank pipes or slotted pipes

by soldering including cost of all required jointing

materials, clamps sets etc with cutting, grinding etc

complete as directed by Engineer incharge.

Supply of best quality of well sorted Sevaliya gravel of

118 size ranging from 4 mm to 6 mm. 25.00 Cum 2049.29

Providing and fixing E.R.W. Bail plug of length

119 meter made from MS medium class pipe as per IS 2.00 Each 851.04

suitable for 200 mm dia pipe.

Supplying & erecting Heavy duty clamp made from 4" x

120 1.5" iron strip suitable for column pipe 1.5" to 2" length. 2.00 Each 212.10

(B) 50mm(2") dia pipe

Supplying & erecting G.l. bend for pipe connections

Supplying, & erecting C.I. swing, check type non-return

122 (Reflux) Valve -ISI marked suitable for following size 2.00 Each 1201.90

Charges for development of bore by giving air with

compressor for requirement as per site situation {600

CFM / 150 PSI upto the any depth, minimum 6 hours}

Supplying submersible pump set for bore of 150 mm.

dia.or more having 3 phase motor capacity 10 H.P. and

124 having (12 Stage) 350 L.P.M. discharge at the head 2.00 Each 42662.40

about 100 mtrs. suitable for 50 mm dia. Delivery pipe

Item No. Item Description Quantities Unit Amount

Supplying & erecting approved make 3 phase motor

control cubical panel made from16 G. CRCA sheet duly

painted with epoxy power painted inside and outside with

hinged doors and locking arrangement, consisting of

suitable size of ON- OFF isolator (AC - 3/23 duty) main

fuses, single phasing preventor cum water level. Guard

(Complete unit), Toggle switch to by pass Single phase

preventer cum WLG, indicating lamps for R- Y- B

phases, over load relay, Automatic water level controller,

125 Ammeter & Voltmeter each with two way selector switch 2.00 Each 16053.95

incoming wires duly socket Crimped, Panel to be erected

on angle iron frame grouted on wall as directed. Star

Delta & main contactor, overload relay, thermal /

Electronic Star delta cutoff timer, start - stop push

buttons. The isolator overload relay & contactors of L& T,

Siemens or Cuttler Hamer make only. Panel to be

erected on angle iron frame ground on wall.

Lowering of submersible motor pump set complete with

required. Nos. and size of casing pipes erected by

means of proper chainpulley block & pipe wrenches after

126 checking of threads of each pipe with coupling to take 1.00 Job 3030.00

the load of the pump set and pipe assembly filled up with

(B) Above 60 mtrs. and Up to 120 mtrs.

Providing and erecting ISI marked PVC insulated PVC

Sheathed Flat flexible Submersible copper cable

approved make of following Size.

(C) 3 Core x 4 Sq. mm

Supplying ISI Marked (Embossed) following size of

Heavy duty "C" Class G.I. Pipe & erecting etc complete

128 as per instruction of Engineer in charge & approved 100.00 Rmt 418.14

make with necessary plumbing as desired.

Supplying and erecting with leak proof materials, M.S.

Heavy duty ISI marked coupling having threads of

129 TPI/11 TPI suitable for 'C' class pipe to take load of 90.00 Each 107.06

pump and pipe assembly of following size and TPI.

(C) 50 mm(2") dia. pipe 8 TPI

Add cost of leak proof complete welding surrounding

130 pipe and coupling for use as column pipe for following 90.00 Each 70.70

Cutting the heavy duty pipe and threading one end of

pipe with 8 TPI / 11 TPI as per requirement and including

131 to and fro charges 90.00 Each 81.81

(B) 50mm (2") dia pipe

Plantation of trees in soil incl digging 45 x 45 x 45cm size

pits, preparing soil, providing and mixing organic

132 fertilizers, watering planting and filling the pits as per 15.00 No 35.35

direction including etc complete.

Providing Tree Plants having minimum 1.00 mt

Height and healthy growth of various kinds as like

133 Peltophorum, Gulmohar, Karanj, Ambala ,Rain tree 15.00 No 27.27

Saptaparni, Cherry, Cryjeliya , Spethodiya, Paras Pipala,

Garmalo, Neem , Borsalli, Kadam Buch, Champo.

Item No. Item Description Quantities Unit Amount

Maintanance of Planted tree upto Two Year incl

times Watering, at regular interval digging pits,trimmimg

applying Fertilizer insecticides . pesticides and

134 Pesticides and replacing plants if necessary etc 15.00 No 358.55

complete for raising of Plants weeding or soil working

Providing and fixing TREE GUARD 2.00 mt. long & of

600mm dia square mesh of 50 X 50 mm and M.S. Flat of

135 25mm x 5 mm vertical support and three rings of 20 x 3 15.00 No 2494.70

mm flat, fixing on site in M150 etc complete as directed

by Engineer in charge.

Providing and fixing pre-cast concrete kerb stone of gray

cement based concrete block 30cm length,30cm height

and 15cm thick of M250 grade concret as per approved

136 design and including excavation for fixing in proper line 44.80 Rmt 400.87

and level,filling the joint with C:M 1:3 (1cement:3fine

sand) etc complete. (upto 10 ton)

Painting lines, dashes, arrows, letters, etc. on roads, air

fields and like in two coats with road marking paint

137 Brushing including cleaning the surface of all dirt, dust 26.88 Sqm 130.28

and other foreign matter. (1) Over 10 c.m. in width

Providing and Fixing on site sandwich type colour granite

stone decorative seating highback 0.75 mtr arrangement

having size 2.5 X 0.6 mtr and 0.45 mtr hight and 20mm

138 thick both side polished granite stone including, cutting, 4.00 No 8585.00

fixing, jointing with white cement, colour pigment,

moulding of edge and finishing with Foundation base etc

detailed drawing as directed by Engineer incharge.

Excavation for foundation upto1.50 MT depth including

sorting out and stacking of useful materials and

disposing the excavated stuff up to 50 mt lead. ( B )

Loose or soft soil

15mm the cement plaster in single coat on fair side of

brick / concrete wall for interior plastering up to floor two

140 level finished even and smooth in C M 1:3 ( 1 cement : 3 5.47 Sqm 161.20

coarse sand) including finishing with a a floating coat of

neat cement slurry complete. For Ground floor

Supplying of crushed stone aggregates Chippings etc of

hard stone of 25 to 40 mm nominal size free of

141 disintegrated pieces. Deleterious and organic matter (for 0.86 Cum 782.18

bitumen surface dressing etc.) and gradings with all lead

Drilling of 200 / 215 mm dia. bore hole in overburden

strata by DTH rig up to required depth including fixing of

175 / 180 dia MS ERW / PVC casing pipe & further

142 drilling of 165 mm dia. bore hole in hard rock (trap etc.) 30.00 Rmt 266.64

strata by DTH drilling method up to total depth of

meters including measuring the yield by V notch and

flushing of bore etc. complete in all districts of Zone V.

( Casing up to 12 Mts.)

Manufacture, supply & delivery of ISI marked UPVC

Casing pipe (IS 12818 with latest amendment. (Rates

143 are exclusive of GST)175.00 mm nominal dia. " CS " 20.00 Rmt 1064.54

Type including lowering etc complete

Item No. Item Description Quantities Unit Amount

Providing and fixing Box type wooden Wardrobe 450 mm

deep with 18 mm thick BWP shutter as per detailed

drawing of each room including facility of Pull out

Drawer, Shelf, Shelf Hanger, Drawer, Jwellery Drawer,

144 laguage space, inside cover with liner and outside 44.10 Sqm 9195.62

finishwith 1 mm thick laminates including edge covering

with Indian teakwood patti with wooden polish groov type

handle using all necessary material etc complete as

directed by Engineer incharge. (Measure Front Elevation

Item No. Item Description Quantities Unit Amount

Providing and Fixing of 32 mm dia Rod SS 304 grade

including fixing with SS hook 100 mm long etc using with

all necessary materials like Clamp, screw, wire nail, etc

as directed by Engineer incharge.

ABC Type DCP Extinguishers 6 Kg ( MAKE-KANEX,

ATASEE, SAFEX )

4.2 Kg CO2 Capacity ( MAKE-KANEX, ATASEE, SAFEX

Point wiring for FAN with 2-1.5 sq.mm & earth wire of

1.5 sq.mm (Green) both are of .ISI marked 1.1 kV Grade

FRLS PVC insulated multi strand copper wires up to

mtr length, in below type of pipe erected with 6A

Modular type switch and hum free EME step type

electronic fan regulator mounted and accessories with

148 earth continuity of following type erected on PVC / 20.00 Pts. 626.20

Metallic/Wooden box, single mounting base frame

covered with textured/metallic/white front plate modules

erected on / in wall / ceiling as per pipe erected. with

necessary ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete CATlll

Point wiring for Light / Bell with 2-1.5 sq.mm & earth

wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 kV

grade FRLS PVC insulated multi strand copper wires up

to 10 mtr length , in below type of pipe erected with 6A

Modular type switch / bell push & accessories and earth

continuity of following type, erected on PVC /

149 Metallic/Wooden box, single mounting base frame 70.00 Pts. 582.77

covered with textured/metallic/white front plate modules

erected on / in wall / ceiling as per pipe erected, with

necessary Lamp holder/ceiling rose / H.D.Connector as

(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete cat lll

Point wiring for on board Looped Plug with 6A Modular

type switch & 5 pin socket erected on PVC /

150 Metallic/Wooden box, single mounting base frame 56.00 Pts. 309.06

covered with textured / metallic/white front plate

modules erected on / in wall / ceiling with following type

accessories cat lll

Providing following type of Modular Type Accessories

mounted with PVC / metallic/Wooden box, single

151 mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge.

(10) 6/16Amp. Universal socket Cat.III 44.00 Ea 199.98

(9) 16 Amp. SP one way switch Cat.III 44.00 Ea 180.79

Providing and erecting Mains with 1.1 KV grade FRLS

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected concealed in

/flushed on wall/ceiling, with 1.5 sq. mm copper

152 conductor FRLS PVC insulated stranded wire of green 896.00 Mtr. 104.03

colour for earth continuity of following size Cat.III

(A) with medium class Rigid PVC pipe and accessories

(b) 2 wire 2.5 sq. mm

Providing and erecting ISI mark Medium class RIGID

PVC PIPES of following size complete to be erected

153 on/in wall or ceiling erected with necessary PVC fittings

& Junction boxes fixed with adhesive solution & Clamps

with following dia of pipes, in approved manner as

Item No. Item Description Quantities Unit Amount

providing and erecting Mains with 1.1 kV grade FRLS

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected in / on wall /

154 ceiling with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth

continuity of following size

(A) with medium class Rigid PVC pipe and accessories

(a) 2 wire 4 sq. mm 256.00 Mtr. 140.39

(i) 4 wire 10 sq. mm

(use earth wire of 4 sq.mm )

providing and erecting Mains with ISI marked, 1.5kV

grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms to

155 IS 694, IEC - 227 erected in existing pipe of following

size (Specifically for control panel, relays, power

switchgears, motor starters & control wiring) with

required size of copper lugs, nuts and bolts if required.

(b) One wire 1.50 sq. mm 6.00 Mtr. 22.22

(f) One wire 10.00 sq. mm 18.00 Mtr. 115.14

Supplying and erecting Flexible PVC insulated multi

strand multi core 1.1 kV grade ISI marked copper wires

of following size to be erected as directed.

e) 1.50 Sq.mm 3 core round PVC sheathed

Decorative call bell Ting-tong box type 250 volts

complete erected

Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be

made of thick sheet Steel conforming to IS: 513/CRCA/

aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company

mark/name 160V to 270V, Power Factor more than 0.95,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges

shown.)(A) Tube Light with integral driver (v) 36-40

Watts, Surge-2 kV, IP-20, conventional 4 feet CAT lll

Supplying and erecting led lamps with following wattage

capacity of 220 to 240 voltage, minimum 15000 burning

hours life, 500 V in built-surge protection,Polycarbonate

159 diffuser, mounting suitable for E14 / E27 / B22 lamp 32.00 Ea 112.11

(A) LED Lamps integral type, with PC diffuser suitable

LAMP holder (ii) 5 to 8 watts cat lll

Item No. Item Description Quantities Unit Amount

Supplying and erecting LED street light / Flood light

fittings with High power White LEDs wattage of 3 Watt

and above assembled on single MCPCB, efficiency more

than 130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated and

heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened glass with

company mark/name engraved or embossed 160 to

V,Power Factor more than 0.95, THD < 10 %, CCT

160 3000 K to 5700K,Uniformity ratio >0.45, Luminaire 9.00 Ea 4248.06

efficacy> 100 lumens/watt . LED driver efficiency >

%.( fittings required LM-79 & LM-80 certificates)(NOTE:

Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges shown.)

(A) Street Light (IP-65), Surge protection -4KV integral

and ,Light must have 440VAC line supply with over-

voltage protection. (ii) above 48 to 59 Watts cat lll

Providing and erecting Approved make Four pole

moulded case circuit breaker having breaking capacity

ICU of 25 KA. at 415 V,having normal current rating up

161 to 25 A to 100A. with Fixed thermal & magnetic release 1.00 Ea 6790.23

suitable to work on A.C. supply 50 Hz. with all internal

connections, spreader tinned copper & complete erected

in existing 16 G.M.S. housing.

ICS=100% of ICU only Cat III

Supplying and erecting triple pole & neutral 440V/ 500V

panel mounting Aluminium Busbars with four equal Nos.

of bus having current density not more than 0.8 Amp. /

sq.mm (Rated current / cross section area) duly wrapped

162 with colour insulating tape for phase sequence of 0.50 Rn.mtr 660.54

following current carrying capacity, erected with

necessary bus bar supports /insulators, main cable

socket to each busbar,erected in existing cubical panel

with necessary connections. (A) Suitable for 100 Amp.

Supplying & erecting approved make Digital time switch

having lithium cell 6 years operative and operate battery

backup 1 channel day clock with 14 memory programme,

suitable to operate on 240V + 5%, 16A with, floating

163 contacts Minimum switching setup time 1 minimum & 1.00 Ea 3168.37

LCD display. Also comprised permanent ON/OFF

switching. Programming switches & housed in fire proof

thermoplastic enclosure & transparent cover erected as

required with necessary connection erected as directed.

Supplying & erecting power contactor ,AC3 duty for time

164 switch complete erected as per direction Cat III D) 4 pole 1.00 Ea 2782.55

Supplying and erecting approved make suitable panel

165 indicator LED type lamp, lens cover, complete erected 3.00 Ea 43.43

with necessary connections.

providing and erecting Miniature circuit breaker single

pole 0.5A to 2A system and having breaking capacity

KA to be erected in existing box. confirming to IS

8828/1996 with ISI Mark cat lll

providing and erecting Miniature circuit breaker single

pole 6A to 25A suitable to operate on 240 V A.C. system

167 and having breaking capacity 10 KA to be erected in 72.00 Ea 123.22

existing box. confirming to IS 8828/1996 with ISI Mark

Item No. Item Description Quantities Unit Amount

Providing & erecting 240 V MCB double pole switch for

motor & inductive load (C Curve) having 10 KA

breaking capacity & confirms to IS : 8828 in existing box

having following capacity (B) 40 Amp. Cat.III

Providing & erecting 415 V MCB Four Pole for Motor &

Inductive Load (C Curve) having 10KA breaking

capacity & confirms to IS :8828 in existing box having

following capacity (c)63 Amp. Cat lll

Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to

170 IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be used of

same company of MCB to be used) suitable for

(B) three phase incoming and single phase horizontal

type outgoing Per phase isolation type (PPI) (b) sheet 4.00 Ea 3412.79

steel double door (iii)8 way

providing and erecting Approved make RCCBs

conforming to IS: 12640 and having sensitivity of 30 mA

and Short Circuit withstand capacity of 10 KA and

171 suitable for operation on single phase 240 V,50Hz. 12.00 Ea 2458.34

having characteristic of quick action & tripping with all

advance feature & do not incorporate any electronic

component. for following Max. rating erected as directed

(ii) 40Amps. DP cat lll

Providing and erecting Approved make RCCBs

conforming to IS: 12640 and having sensitivity of 30 mA

and Short Circuit withstand capacity of 10 KA and

172 suitable for operation on 3 phase and neutral 2.00 Ea 2900.72

415V,50Hz. having characteristic of quick action &

tripping with all advance feature & do not incorporate any

electronic component for following Max. rating erected

as directed. (ii) 40Amps. FP cat lll

Providing and erecting HOT deep Galvanised iron

strip/wire 4.064mm to 1.626mm.

Supplying & erecting in earthpit of minimum bore dia.

225mm size approved make Safe Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-1987

made of corrosion free hot dipped G.I.Pipes having

Outer pipe dia of 80 mm having 80-200 Micron

galvanising, Inner pipe dia of 40 mm having 200-250

Micron galvanising, connection terminal dia of 14 mm

with constant ohmic value surrounded by highly

conductive compound with high charge dissipation

suitable for following type of applications with chamber

and heavy duty cover (A)(approved make OEM has to

submit test certificate including value of earth resistance

174 of installation duly stamped and signed by agency and 5.00 Ea 5842.85

officer Incharge has to ensure the value of earthing

resistane mentioned in test Certificate) & having back

filling compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 ohm / meter testing as per

IEC 62561-2017, Voltage drop:- < 1 volt at no load & dry

form, Sulphar content:- <2%(C) Back fill Compound :-

Earthing compound should be capable to retain moisture

for long time Necessary test report must be submitted

by Agency. Length of Pipe - 1 MtrBack filling compound -

1 Nos. of Bag of 15 Kgs.[A] For electrical installation up

to 440 V Length of Pipe - 1 Mtr Back filling compound -

Providing of erecting

and 15 Kgs. FRLS-XLPE (IS:7098)(I)-88 ISI

armoured cable multistrand / Solid Aluminium conductor

for 1.1 kV. to be laid on wall with necessary clamps or

in existing trench / pipe of following size of cables

Item No. Item Description Quantities Unit Amount

(B) 4 core 6 Sq. mm 200.00 Mtr 151.50

Making trench in Hard Murrum / Tar Road of suitable

width of 90 cm or required depth for laying any size of

cable or locating the fault all over the run and back filling

the same and making the surface as normal ground.

Providing & laying approved make ISI marked HDPE

6Kg / cm2 (Class-3) as per IS:4984:1995 PE-80 to be

177 erected at road crossing on or floor as directed for laying

of cable. The pipes as following size of dia & weight per

(A) 40 mm inner Dia. 88.00 Mtr. 108.07

Providing and, fixing heavy duty flange type brass cable

gland with rubber ring for PVC insulated armoured cable

complete with out going tails, insulating tape etc for

following size of cables.(b) 2 to 4 core 6 Sq. mm

Solder less crimping type Aluminium lugs conforming to

IS suitable for cable of following size evenly crimped with

179 high pressure tool & connected to switchgear terminals

with brass/cadmium plated nut bolts in an approved

Providing & erecting Approved make Power Saving 45 -

50 Watt Ceiling Fan with double ball bearing ISI mark

180 with Condenser 230 volt A.C. 50 Hz 1200 mm sweep 20.00 Ea 1948.29

complete having 3blades with aluminium blades with

canopy & 30 cm. down rod erected with earthing.(Make

shall be approved by Engineer in charge))

Supplying and erecting 19 / 20 mm. nominal bore

Medium Class M.S. Pipe down rod erected duly painted

for fan complete with proper insulation without leakage

Supplying & erecting fan hook box of 10 mm M.S.

round bar bounded to the RCC bars up to 50mm length

182 each side and pierced through a 16 Gauge M.S. box / 20.00 Ea 108.07

Heavy Duty PVC box complete erected concealed in

Ceiling with necessary finishing.

Item No. Item Description Quantities Unit Amount

Providing 2.5mm.thick laminated acrylic sheet to cover

the fan hook or Fan box.

Supplying & erecting approved make low noise

decorative exhaust fan having square frame ABS body

with inbuilt lowers & square frame. 200mm with

Supplying and erecting approved make Octagonal pole

made from HR sheet steel. The pole should be made as

per IS. and shall be coated with hot dip galvanizing as

per IS 2629/2633/4759, suitable suspend local wind

speed with integral Junction box consist of terminal plate

of min 6mm Hylam sheet, standard profile 35mmX7.5mm

Din-Rail for MCB Mounting, stud type terminal and

185 arrangement for cable termination to be erected With 3.00 Ea. 7561.87

Suitable foundation (Included) as per details given by

manufacturer considering site requirement.

(C) 5 Mtr. Long 70 mm Top X 130 mm bottom dia, 3 mm

thickness with 200mmX200mmX12mm base plate, 4-

M16 Bolts and 600mm long with necessary G.I. J Bolts

.Approx Pole weight 46 kg

Providing and erecting street light pole bracket

comprising main B Class GI pipe of 4.2 cm/require

outside dia. complete with suitable B Class G.I sleeve

tubing of approx. 45cms.length and suitable for 76.5 mm

/ 80mm. / require size pole top having sufficient

186 fasteners for fixing the brackets and having spread of 1 3.00 Ea. 614.08

mtr. length with suitable rise as per site condition &

suitable welded stiffener reducer and nipple with check

nut complete painted with one coat of Red oxide / PU

base primer and two coats of Aluminium / PU paint. paint

with following nos of arms.

[A] Single Arm bracket 1 Mtr

Item No. Item Description Quantities Unit Amount

Supplying & erecting IP 55 grade following size section

pillar fabricated from joint less M.S. Sheet with angle iron

legs made from jointless M.S. Angle with cable clamps to

187 be buried in ground to have appropriate erection to work

uniform until erected with cement concrete foundation

and 45 cm high bricks work finishing with plaster etc.

hinged double door internally supported on both side,

with internal and outside looking arrangement with look

and keys in duplicate 35 x 35 x 5 mm M.S. Angle of Two

Nos. one is welded and other with nut and bolt for

erecting Bakelite sheet. Painting the Section Pillar inside

and out side with three tank powder coated paint.

section pillar roof should be without joint with water 1.00 Ea 3595.60

leakage proof & tested as per IP 55 test & followed by IS

2147 of 1962 (B) 75 X 60 X 45 cm section pillar

fabricated from 16 Gauge MS Sheet with angle iron legs

45 cm long made from 35 X 35 X 5 mm thick MS angle.

Supplying and erecting HYLAM sheet on existing angle

iron frame.for following thickness (A) 2mm

Providing & erecting open well horizontal mono block

pump set with cast iron body, complete for three phase

189 submersible motor having[B] For 2 HP 3 phase open well 1.00 Ea 11807.91

horizontal mono block pump set suitable for 200 LPM @

25 mtr head suitable for 50 mm dia delivery pipe cat ll

Supplying & erecting approved make motor control

cubical panel (Direct - on - line) made from 16 G. CRCA

sheet duly epoxy powder painted inside and outside with

hinged doors and locking, arrangement consisting of

suitable size of ON- OFF isolator (AC - 3/23duty) main

fuses, single phasing preventer, indicating lamps for R-

190 Y - B phases, overload relay, Automatic water level 1.00 Ea 7722.46

controller, Ammeter, Voltmeter each with two way

selector switch incoming, wires duly socket crimped,

main contactor & overload relay, start - stop push

buttons, to be erected on angle iron frame grouted on

wall as directed. The isolator, overload relay &

contactors will be of L & T, Siemens or BCH make only.

(A) DOL up to 5.0 H.P.

Item No. Item Description Quantities Unit Amount

Providing and erecting ISI marked PVC insulated PVC

Sheathed Flat flexible Submersible copper cable

approved make of following Size. (C) 3 Core x 4 Sq.

Supplying & erecting approved make SMC press

moulded composite FRP. loop-in, loop-out approx. 2mm

thick box complete with Bakelite connector strip

5way(3P+N+E),DIN rail for mounting mob & hinged

192 doors as per requirement having locking arrangements 6.00 Ea 476.72

with mounting clamp with nuts, bolts & washers suitable

for erection on pole with cable clamps& earth bolt of

following size of box. (C)150mm x 125mm x 100mm

Supplying and erecting B class galvanised iron pipe

mm outside dia 45 cm long duly welded on 20 cm x

193 cm x 3 mm thick M.S. base plate, erected on wall or 6.00 Ea 343.40

corner for mounting street light luminaire with necessary

hardware materials duly painted.

I/We am/are willing to carry out the work at…% above/below percent(Should be written in figures and words) of the estimated

rate mentioned above. Amount of my /our tender works out as under.

(A) Estimated amount put to tender Estimated amount put to tender

(B) Deduct………% below Add………% below

(Rs. in Words __________________Only). (Rs. in Words __________________Only).

(* Please strike out whichever is not applicable).

1. The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-

Charge for which no extra payment shall be made.

2. The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3. GST and Income tax TDS will be deducted at a source while making payments of bills.

4. In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-

10/2017 Cement Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where there

is a change as per actual mix design the cost of difference of cement consumption have been deducted from the rate

of original item at the rate of input rate mentioned in all the tender.

Dated Signature of Deputy Executive Engineer Executive Engineer

the Contractor. R & B (P) Sub Division R & B (P) Division

Bhachau-Kutch Bhuj-Kutch