Construction of New 4 Nos. C Type Category Quarter for PHC Balasar Taluka Rapar, Kutch

Name of work: Construction of New 4 Nos. C Type Category Quarter for

PHC Balasar Taluka Rapar, Kutch

BILL OF QUANTITIES

Item No. Item Description Quantities Unit Amount

Excavation for foundation upto 1.5 m depth including

sorting out and stacking of useful materials and

1 disposing off the excavated stuff as directed upto 50 347.36 Cum 157.33

Meter lead (B) Dense or hard soil

Excavation for foundation for depth from 1.5 m to

m including sorting out and stacking of useful materials

2 and disposing off the excavated stuff as directed upto 111.46 Cum 170.69

50 Meter lead. (B) Dense or hard Soil

Applying general insecticide pest control treatment to

floors, cupboards etc including labour material etc.

complete. Using Imidacloprid 30.5Sc As Per IS

3 part‐ II (0.075% cocentration by mass) is recommended 246.23 Sqm 91.63

10.5ml chemical dillute with 5 liter of water appication

0.5 Litre chemical / Sqm of surface is recommended as

Providing & laying controlled cement concrete M150 for

curing complete including cost of form work but

excluding cost of reinforcement for reinforced conrete

work in foundation and plinth.

Providing and laying Controlled cement concrete M250

and curing complete including the cost of formwork but

excluding the cost of reinforcement for RCC work. (a)

Foundation, Footing base of column mass concrete.

For Column Footing.

Providing & Laying controlled cement concrete M250

and curing complete including cost of formwork but

excluding the cost of reinforcement for reinforced

concrete work in Grade Slab.

Compaction and finishing of cement concrete road by

tremix process, providing extra labour charge for tremix

(Vaccum dewatering service) process on cement

concrete road surface by using vaccum dewatering

7 pump floater surface vibrator including making groove 463.26 Sqm 71.21

5mm width and filling with polyvynile polymer and rough

finish to surface as per instruction including leveling etc

Providing and laying Controlled cement concrete M250

and curing complete including the cost of form work but

excluding the cost of reinforcement for RCC work (B)

Filling available excavated earth excluding rock in

trenches plinth side of foundation etc in layer not

9 exceeding 20 cm in depth consolidation each deposit 215.17 Cum 136.92

layer by ramming and watering.

Filling in plinth with sand under floors including

watering, ramming, consolidating and dressing etc

10 complete as directed by Engineer in charge. 23.03 Cum 481.80

Item No. Item Description Quantities Unit Amount

Providing and laying Controlled cement concrete M250

and curing complete including the cost of form work but

11 excluding the cost of reinforcement for RCC work for 12.94 Cum 6824.34

GF (C) Column for Hollow Plinth/Parking.

Providing and laying Controlled cement concrete M250

and curing etc. complete including the cost of form

work but excluding the cost of reinforcement for RCC

12 work for GF (B) Beam for Hollow Plinth/Parking.(GF 21.42 Cum 5938.40

Providing and laying Controlled cement concrete M250

and curing complete including the cost of form work but

excluding the cost of reinforcement for RCC work GF

(B) Slab for hollow plinth/Parking (GF Slab lvl).

Providing and laying Controlled cement concrete M250

and curing complete including the cost of form work but

14 excluding the cost of reinforcement for RCC work (C) 9.92 Cum 6865.28

Providing and laying Controlled cement concrete M250

and curing etc. complete including the cost of form

15 work but excluding the cost of reinforcement for RCC 18.23 Cum 5979.34

work (B) Beam for FF (SF slab lvl).

Providing and laying Controlled cement concrete M250

and curing complete including the cost of form work but

16 excluding the cost of reinforcement for RCC work (B) 17.01 Cum 5300.66

Slab for FF (SF slab lvl).

Provinding and Laying controlled cement concrete

M250 including finishing smooth and curing

etc.complete including the cost of formwork but

excluding the cost of reinforcement for R.C.C work in

Providing and laying controlled cement concrete M250

upto floor two level and curing complete including

finishing with a floating coat of neat cement slurry the

18 cost of form work but excluding the cost of 0.92 Cum 7533.89

reinforcement for RCC work in Chajjas For FF.

Providing and laying Controlled cement concrete M250

and curing complete including the cost of form work but

excluding the cost of reinforcement for RCC work (C)

19 Column for SF. 9.92 Cum 6906.21

Providing and laying Controlled cement concrete M250

and curing etc. complete including the cost of form

work but excluding the cost of reinforcement for RCC

20 work (B) Beam for SF (SF Slab lvl). 18.23 Cum 6020.28

Item No. Item Description Quantities Unit Amount

Providing and laying Controlled cement concrete M250

and curing complete including the cost of form work but

excluding the cost of reinforcement for RCC work (B)

21 Slab for SF(SF Slab lvl). 17.01 Cum 5341.60

Provinding and Laying controlled cement concrete

M250 including finishing smooth and curing

etc.complete including the cost of formwork but

22 excluding the cost of reinforcement for R.C.C work in 3.45 Cum 8325.93

Providing and laying controlled cement concrete M250

upto floor two level and curing complete including

23 finishing with a floating coat of neat cement slurry the 0.92 Cum 7574.83

cost of form work but excluding the cost of

reinforcement for RCC work in Chajjas For SF.

Providing and laying Controlled cement concrete M250

and curing complete including the cost of form work but

24 excluding the cost of reinforcement for RCC work in 2.27 Cum 6947.15

column for TF (C) Column for Stair cabin

Providing and laying Controlled cement concrete M250

and curing etc. complete including the cost of form

work but excluding the cost of reinforcement for RCC

25 work in beam for TF (B) Beam for TF Stair cabin. 2.17 Cum 6061.21

Providing and laying Controlled cement concrete M250

and curing complete including the cost of form work but

excluding the cost of reinforcement for RCC work in

26 slab for TF (B) Slab for TF (Stair cabin Slab lvl). 2.06 Cum 5382.53

Providing and laying controlled cement concrete M250

upto floor two level and curing complete including

finishing with a floating coat of neat cement slurry the

27 cost of form work but excluding the cost of 0.14 Cum 7615.76

reinforcement for RCC work in Chajjas For Stair Cabin.

Providing and fixingTMT FE 500 D Anchor/Rebaring

bars of minimum 12 mm dia, length of bar 300 mm for

anchoring by drilling holes minimum 100 mm deep in

existing RCC/Masonary Work, including properly

28 placing of bars and grouting the holes with sealing with 290.00 Nos 25.25

appoxy material finishing the same etc complete as

directed by Engineer incharge.

Providing and laying controlled cement concrete M250

and curing complete including the cost of formwork

and excluding the cost of reinforcement for reinforced

29 concrete work in (E) Staircase for All floor 10.41 Cum 7914.92

Item No. Item Description Quantities Unit Amount

Providing ISI mark TMT bar FE 500D reinforcement for

R.C.C work including bending, binding and placing in

position etc complete upto All Floor Level.

Brick work using common burnt clay building bricks

having crushing strength not less than 35 Kg./Sq.Cm. in

foundation and plinth in cement mortar 1:5 ( 1-cement :

31 5-fine sand ) (B) Conventional For upto Plinth. 16.86 Cum 4245.09

Brick work using common burnt clay building bricks

having crushing strength not less than 35 Kg./Sq.Cm. in

foundation and plinth in cement mortar 1:5 ( 1-cement :

32 5-fine sand ) (B) Conventional For Ground Floor / 10.64 Cum 4526.81

Hollow Plinth / Parking.

Brick work using common burnt clay building bricks

having crushing strength not less than 35 Kg./Sq.Cm. in

cement mortar 1:5 ( 1-cement : 5-fine sand ) in super

33 structure above plinth level upto floor two level. (B) 52.57 Cum 4850.96

Conventional For First Floor

Brick work using common burnt clay building bricks

having crushing strength not less than 35 Kg./Sq.Cm. in

cement mortar 1:5 ( 1-cement : 5-fine sand ) in super

34 structure above plinth level upto floor two level. (B) 52.57 Cum 4893.39

Conventional For Second Floor

Item No. Item Description Quantities Unit Amount

Brick work using common burnt clay building bricks

having crushing strength not less than 35 Kg./Sq.Cm. in

cement mortar 1:5 ( 1-cement : 5-fine sand ) in super

35 structure above plinth level upto floor two level. (B) 19.08 Cum 4935.82

Conventional For Terrace Floor

Half brick masonary in common burnt clay building

bricks having crushing strength not less than

35kg/sq.cm. in cement mortar 1:3 (1-cement : 3-coarse

36 sand ) with 2 Nos of 8mm TMT steel round bars after 56.89 Sqm 811.49

every three course embedded in Cement Mortar in

superstructure above plinth level. (B) Conventional (For

Half brick masonary in common burnt clay building

bricks having crushing strength not less than

35kg/sq.cm. in cement mortar 1:3 (1-cement : 3-coarse

sand ) with 2 Nos of 8mm TMT steel round bars after

every three course embedded in Cement Mortar in

superstructure above plinth level. (B) Conventional (For

Half brick masonary in common burnt clay building

bricks having crushing strength not less than

35kg/sq.cm. in cement mortar 1:3 (1-cement : 3-coarse

sand ) with 2 Nos of 8mm TMT steel round bars after

every three course embedded in Cement Mortar in

superstructure above plinth level. (B) Conventional (For

Providing and fixing side hunge Single shutter Door

including using Anodized Aluminium Section domel

series frame having zindal Door Section no.

weight not less than 1.1 Kg/mt, 35 mm thick and pannel

of both side Pre laminated Water Boiling Proof Plywood

particle board 12 mm thick of natural wood grain shed,

1mm thick laminated with fixing of 2x3 cm T.W.

moulding on both side, fixing of 5 mm thick tranparent

glass in top ventilator as per detail drawing including

three coat of oil paint with primer etc complete as per

instruction of Engineer in charge & approved make.

Providing and Fixing of 100 X 50 mm thick FRP frame

with 35mm thick FRP shutter with 1.5 to 2.0 mm thick

fire retardent grade FRP skin in wood grain rasied panel

design having extra reinforcement on sides &

edges & in polish design finish. The core of the shutter

is to be filled up with injected retardent grade

polyurethane foam done in situ alongwith embedded

wooden pieces for stiffening & also taking hinges

& fixtures. The whole shutter is to be water proof,

weather proof, termite proof & resistance to mild

acid/alkali. Rates are to be inclusive of S.S hinges with

necessary screws & alluminium S.S finish fixtures &

fastenings as per instruction of Engineer in charge &

Item No. Item Description Quantities Unit Amount

Providing and fixing window having extruded aluminum

Colour anodized section frame main outer size 95mm x

24mm x 1.17mm @ wt.of 0.738 Kg/mt , horizontal

Three track member size 92mm x 31.75mm x

1.30mm,@ Wt.1.07 Kg/mt , vertical member of size

92mm x 31.75mm x 1.50mm @ Wt. 1.06 Kg/mt with

sliding shutters of horizontal member size

mmx18mm x1.29mm @ wt.of 0.456 Kg/mt, vertical

member of size 40mm x 18mm x 1.29 mm @ wt.of

0.456Kg/mt/ with 5 mm thick transparent bronze colour

tinted float glass with SS 304 Mosquito net with powder

coated aluminum fittings and fixtures and transparent

silicon sealant

Providing glass fixing

and fixing windowto frame

havingas per details

Colour anodized section frame main outer size 63.50 x

38.10 x 1.95 mm,@ Wt 1.094 Kg / Rmt, horizontal Two

track member size 61.85 mm x 31.75 mm x 1.20mm @

wt.of 0.695 Kg/mt, vertical member of size 61.85 mm x

31.75mm x 1.30 mm @ wt.of 0.659 Kg/mt with sliding

shutters of horizontal member size 40mm x 18mm x

1.29mm @ wt.of 0.456Kg/mt, vertical member of size

0.457 Kg/mt with 5 mm thick transparent bronze colour

tinted float glass with powder coated aluminum fittings

and fixtures and transparent silicon sealant glass fixing

Providing perfixing

S.S. complete for window.

mosquito net jali fixing in

Aluminium section of size 62.5 X 62.5 X 1.25 mm of

43 Square pipe using angle section for fixing of S.S. Jali 2.88 Sqm 3825.54

With Rubber Gasket/Patti as directed by Engineer in

charge. Ventilation - V

Providing and fixing M.S. grills/ Railing of required

pattern to M.S. frames of windows ,Door , Jali etc.

with M.S. flats at required spacings and frame alround,

44 square or round Bright bars of 16mm dia, with 890.09 Kg 123.14

round headed bolts and nuts or by screws including

One coat of primer and two coat of oil paints, all Fixture

etc complete as directed by Engineer in charge.

Providing and fixing MS pipe of 50 mm dia, wall

thicness 3.20 mm and weight 4.20 per Rmt including,

cutting, bending, binding, welding, grinding of pipe, end

45 covering with same material fixing in masonary work, 37.20 Rmt 1082.07

finishing the same etc complete as directed by

Engineer Incharge.

Providing 20 mm thick Double coat mala cement

plaster on interior brick / concrete work for plastering

comprising of base coat of 12 mm thick cement plaster

in cement mortar (1 Cement : 4 coarse sand) in rough

46 finishing and 8 mm thick top coat of cement mortar 1:2 350.90 Sqm 265.65

(1 Cement : 2 Coarse sand) finished with trovel

including with mixing of waterproofing material

scaffolding curing, 10x10 mm Joints grooves etc.

complete for All Floors with. For GF Parking.

Item No. Item Description Quantities Unit Amount

Providing 20 mm thick Double coat mala cement

plaster on interior brick / concrete work for plastering

comprising of base coat of 12 mm thick cement plaster

in cement mortar (1 Cement : 4 coarse sand) in rough

finishing and 8 mm thick top coat of cement mortar 1:2

(1 Cement : 2 Coarse sand) finished with trovel

including with mixing of waterproofing material

scaffolding curing, 10x10 mm Joints grooves etc.

complete for All Floors with. For First Floor

Providing 20 mm thick Double coat mala cement

plaster on interior brick / concrete work for plastering

comprising of base coat of 12 mm thick cement plaster

in cement mortar (1 Cement : 4 coarse sand) in rough

finishing and 8 mm thick top coat of cement mortar 1:2

48 (1 Cement : 2 Coarse sand) finished with trovel 524.53 Sqm 329.82

including with mixing of waterproofing material

scaffolding curing, 10x10 mm Joints grooves etc.

complete for All Floors with. For Second Floor

Providing 20 mm thick Double coat mala cement

plaster on interior brick / concrete work for plastering

comprising of base coat of 12 mm thick cement plaster

in cement mortar (1 Cement : 4 coarse sand) in rough

finishing and 8 mm thick top coat of cement mortar 1:2

49 (1 Cement : 2 Coarse sand) finished with trovel 133.33 Sqm 361.91

including with mixing of waterproofing material

scaffolding curing, 10x10 mm Joints grooves etc.

complete for All Floors with. For Terrace Floor

Providing 10mm thick cement plaster in single coat on

AAC Block/concrete walls for interior plastering upto

floor two level and finished even and smooth in (i)

Cement mortar 1:3 (1-cement:3-sand) including

finishing etc complete as directed by Engineer in

50 charge. Ceiling Plaster For Ground Floor slab/Hollow 234.73 Sqm 135.47

Plinth/Parking.

Providing 10mm thick cement plaster in single coat on

AAC Block/concrete walls for interior plastering upto

floor two level and finished even and smooth in (i)

Cement mortar 1:3 (1-cement:3-sand) including

finishing etc complete as directed by Engineer in

51 charge. Ceiling Plaster For First Floor 116.06 Sqm 161.53

Item No. Item Description Quantities Unit Amount

Providing 10mm thick cement plaster in single coat on

AAC Block/concrete walls for interior plastering upto

floor two level and finished even and smooth in (i)

Cement mortar 1:3 (1-cement:3-sand) including

finishing etc complete as directed by Engineer in

52 charge. Ceiling Plaster For Second Floor 116.06 Sqm 187.59

Providing 10mm thick cement plaster in single coat on

AAC Block/concrete walls for interior plastering upto

floor two level and finished even and smooth in (i)

Cement mortar 1:3 (1-cement:3-sand) including

finishing etc complete as directed by Engineer in

53 charge. Ceiling Plaster For Terrace Floor 19.22 Sqm 213.65

Item No. Item Description Quantities Unit Amount

Providing 20 mm thick Sand Faced Gutka Finish

cement plaster on wall up to all height above ground

level consisting of 12 mm thick backing coat of C.M. 1 :

3 (1 cement : 3 sand) and 8 mm thick finishing coat of

C.M. 1 : 1 (1 cement : 1 sand) complete with all lead &

54 Lift as directed by Engineer incharge. 629.72 Sqm 315.69

Applying two coats plastic emulsion paint acrylic laphy

(putty) & two coat of primer of approved brand and

manufacture on new wall surface to give an even shade

including thoroughly brushing the surface free from

mortar dropping and other foreign matter and sand

55 papered smooth as per instruction of Engineer in 1909.14 Sqm 124.96

charge & approved make.

Wall Painting three coats with weather proof acralic

exterior emulsion paint of approved brand and

manufacture and of required shade on exterior wall

surface to give an evev shade over and including a

primary coat with alkaly resistance primer of approved

56 brand after throughly brushing the surface to remove 629.72 Sqm 162.81

all dirt and remain of loose powdered materials etc

complete for all height as per instruction of Engineer in

charge & approved make.

Providing and laying Black Machine Cut free edges,

Machine polished Granite Stone slab 18 mm thick

single piece For Stair, Step, Landing, Skirting etc as per

design including fully moulded round front edge and

1cm nosing and necessary V- groove on trade of steps

57 laid on 20 mm thick cement mortar 1:6 (1-cement : 6 138.05 Sqm 3025.61

coarse sand) jointed with grey cement slurry including

rubbing, polishing & Finishing etc complete as directed

by Enginner in Charge. F1

Providing and laying 60 X 60 cm Glossy finish full body

Granite Vitrified 10 mm thick Tiles Flooring over 20 mm

(avg) thick base of cement mortar 1:6 (1-cement : 6-

58 coarse sand) jointed with white cement with colour 183.34 Sqm 1892.49

pigment, finish the same etc coimplete as directed by

Engineer incharge. F2

Providing and laying 60 X 60 cm Glossy finish full body

Granite Vitrified 10 mm thick Tiles Skirting over 20 mm

(avg) thick base of cement mortar 1:6 (1-cement : 6-

59 coarse sand) jointed with white cement with colour 23.83 Sqm 1853.68

pigment, finish the same etc coimplete as directed by

Engineer incharge. F3

Providing and laying polished Kota stone slab flooring

over 20mm (Average) thick base of cement mortar 1:6

(1-cement : 6-coarse sand) laid over and jointed with

60 grey cement slurry mixed with pigment to match the 48.01 Sqm 1013.87

shade of slab including rubbing and mirror polishing etc.

complete. (A) 25mm thick. F4

Item No. Item Description Quantities Unit Amount

Providing and laying coloured glazed tiles Matt finish

of the size 300 mm x 300 mm x 8 mm in skirting,

61 risers of steps and dedo on 10 mm. thick cement 13.54 Sqm 1488.24

plaster 1:3 (1 cement : 3 coarse sand) & jointed with

white cement slurry. F5

Item No. Item Description Quantities Unit Amount

Providing and laying coloured glazed tiles of the

size 300 mm x 600 mm x 8 mm in skirting, risers of

62 steps and dedo on 10 mm. thick cement plaster 1:3 86.90 Sqm 1562.65

(1 cement : 3 coarse sand) & jointed with white cement

slurry. F6 for Dedo

Providing and laying broken china mosaic flooring for

terrace using 12 mm to 20 mm broken pieces of Water

Proofing glazed tiles to be laid over cement mortar 1:3

to plain or slope and to be tempered to bring mortar

63 creme out upto surface using white cement including 151.34 Sqm 779.70

rounding off junctions and extending them upto

cm along the wall,clearing with water and oxalic acid

etc. as directed by Engineer in charged. F7

Providing and fixing SS 316 Grade 90 cm high

Stainless steel railing made from anticorrosive SS pipe

of 50 mm dia (16Gauge) as hand rail with SS 38 mm

dia (16Gauge) as a vertical support fixed in RCC slab at

1.2m c/c including three horizontal SS pipes of

mm dia (16Gauge) at equal distance fixed by

mm dia (16Gauge) S S pipe including accessories as

per detailed drawing as directed etc complete.

Provision and fixing water closet squatting Orissa type

W.C. pan size 580mm integral footrest and 100 mm P

or S trap and in cluding 25 mm dia CP brass flush

65 valve and GI inlet connection etc. comp. (A) Vitreous 4.00 Nos 1142.10

china long pattern white or color including GI Inlet

connection for flush pipe with WC pan.

Providing & Fixing PVC SWR Nanhi trap IS 14735 for

drain 75mm with jali of the following nominal diameter

66 of self cleansing design with C.I. Screwed down or 12.00 Nos 574.58

hinged gratting including cost of cutting and making

good the walls.

Providing & Fixing S.W. Gully trap with C.I. Greating

brick masonay chamber and water tight C..I Cover with

67 frame of 300 mm X 300 mm Size ( Indian ) with 4.00 Nos 1246.92

standard weight (i) Square mouth traps (C) 150 mm

x100 mm size P or R Type.

Constructing brick masonary chamber for underground

C.I. Inspection chamber and bends with bricks having

crushing strenght not less than 35kg/ cm2 in C.M. 1:5

C.I. Cover with frame ( light duty) 455mm x 610mm

internal dimention total weight of cover with frame to be

not less than 38Kgs (weight of cover 23kg and weight

68 of frame 15Kg). R.C.C. tpp slab with 1:2:4 (1 cement : 2 2.00 Nos 2932.93

coarse sand : 4 graded stone aggregate 10mm nominal

size) foundation concrete 1:5:10 inside plaster 1:3

finished smooth with a floting cost of neat cement on

walls and bed concrete etc. comp. (i) inside dimension

455mm x 610mm & 450mm deep for single pipe

Item No. Item Description Quantities Unit Amount

Constructing brick masonry chamber for underground

C.I. Inspection chamber and bends with briocks having

croshing strength not less than 35Kg. Cm2 in C.M. 1:5

C.I. cover with frame (Light duty) 455mm x 610mm

intenal dimensions total weight of cover with frame to

be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of

frame 15Kg.) (R.C.C. top slabe with 1:2:4 mix (1-

69 cement :2- coarse sand :4-graded stone aggregate 5.00 Nos 3660.76

20mm size) foundation concrete 1:5:10 inside plaster

15mm thick with cement mortar 1:3 finished smooth

with a floating coat of neat cement on walls and bed

concrete etc. complete.(i) Inside dimensions 500mmx

700mm and 450mm deep for pipe line with one or

Providing laying and jointing in true line and level UPVC

SWR pipe Type B pipe confirming to IS 13592 -1992

with one end plain and other end socketed with

rubbering & fitting confirming to ISI 14735-1999 of

approved make for drainage system pipe line,pipe shall

be jointed with each other with rubber lubricant,pipe

shall be fixed on wall using of PVC clamp of the size

70 160mm diameter x 210mm lenght x 196mm high at 45.00 Rmt 712.44

every 2000mm center to center or shall be concealed in

wall as directed including necessary fitting such as

bends,shoes etc. including testing of pipe and joints

and jointed with adhesive solvent cement including cost

of all materials. (i) 75 mm Dia

Providing laying and jointing in true line and level UPVC

SWR pipe Type B pipe confirming to IS 13592 -1992

with one end plain and other end socketed with

rubbering & fitting confirming to ISI 14735-1999 of

approved make for drainage system pipe line,pipe shall

be jointed with each other with rubber lubricant,pipe

shall be fixed on wall using of PVC clamp of the size

71 160mm diameter x 210mm lenght x 196mm high at 204.00 Rmt 876.90

every 2000mm center to center or shall be concealed in

wall as directed including necessary fitting such as

bends,shoes etc. including testing of pipe and joints

and jointed with adhesive solvent cement including cost

of all materials.(ii) 110 mm Dia

Providing & Fixing G.I. Z Type heavy duty clamps with

G.I. 6 mm dia. ring for sutiable dia of pipe for Rain

72 Water, Drainage, Water Supply line including drilling 80.00 Nos 80.80

holes, fixing of pipe, nuts, bolts, washers with all lead &

lift etc complete as directd by Engineer in charge.

Providing and fixing in position cowel went to pipes. (B)

Providing and fixing in position cowel went to pipes. (C)

Item No. Item Description Quantities Unit Amount

Providing and laying in true line and level U.P.V.C (Sch-

40) including fitting as approved by Engineer in charge.

Pipe shall be fixed on the wall with held of clamp at

every two meter c/c shall be concealed or open as

75 directed including necessary fitting etc. including testing 20.00 Rmt 195.67

of pipe and joints and fixing the same with adhesive

solvent including cost of all materials. (iii) 50 mm dia.

Providing and laying in true line and level U.P.V.C (Sch-

40) including fitting as approved by Engineer in charge.

Pipe shall be fixed on the wall with held of clamp at

every two meter c/c shall be concealed or open as

76 directed including necessary fitting etc. including testing 60.00 Rmt 148.12

of pipe and joints and fixing the same with adhesive

solvent including cost of all materials. (iii) 40 mm dia.

Providing and laying in true line and level U.P.V.C (Sch-

40) including fitting as approved by Engineer in charge.

Pipe shall be fixed on the wall with held of clamp at

every two meter c/c shall be concealed or open as

77 directed including necessary fitting etc. including testing 60.00 Rmt 91.84

of pipe and joints and fixing the same with adhesive

solvent including cost of all materials. (ii) 25 mm dia.

Providing and laying in true line and level U.P.V.C (Sch-

40) including fitting as approved by Engineer in charge.

Pipe shall be fixed on the wall with held of clamp at

78 every two meter c/c shall be concealed or open as 40.00 Rmt 72.65

directed including necessary fitting etc. including testing

of pipe and joints and fixing the same with adhesive

solvent including cost of all materials. (ii) 15 mm dia.

Providing and laying (to level or slopes) and jointing

with stiff mixture of Cement Mortar in proportion 1:1 Selt

79 glazed stoneware pipes including cement Concrete 1: 30.00 Rmt 352.73

5: 10 bedding testing of pipes and joints complete. (A)

100mm dia. (112 mm avg. thick bed)

Providing & Fixing gun metal check or non return full

way wheel valve etc. comp.(E) 40 mm dia

Providing & Fixing gun metal check or non return full

way wheel valve etc. comp.(c) 25 mm dia

Providing & Fixing CP brass screw down half turn stop

82 cock of approved quality of 15mm dia.size with 16.00 Nos 205.83

adjustable wall flange.

Providing and fixing 600mm x 120mm glass shelf with

83 C.P. brass bracket and guard rail complete mixed to 8.00 Nos 544.51

wooden plug with C.P. brass screws.

Providing & Fixing C.P. brass towel rail complete with

C.P. brass brackets fixed to wodden plug with C.P.

brass screws (B) 60mm x 20mm size

Item No. Item Description Quantities Unit Amount

Providng and fixing 600mm x 450mm bevelled edge

mirror or decorative of superior glass mounted on 6mm

thick A.C. sheet or plywood plug with C.P. brass

screw and washer.

Providng and filling screened of Brick Bats / Chhara

including consolidation etc complete.

Providing erecting and fixing double coated Syntex

HDPE PVC (ISI) water tank of required capacity each

87 with all necessary fittings and connection etc. complete 6000.00 Ltr 3.95

with all lead and lift on terrace.

Providing and fixing ball cock of approved quality as

directed (A) Copper metal (i) 25mm dia.

Providing and fixing in position 300 to 150mm wide

English / Gujarati letters made from 1.0mm thick

89 stainless steel sheet as directed by Engineer in charge 10.00 Nos 757.50

with all material, hardware, accessories and fitting etc

Providing & Fixing SS 316 Silver Chicken Wire Mesh,

Hexagonal Wiremesh jali of 20 gauge at junction of the

90 brick masonary and reinforced cement concrete 55.64 Sqm 49.49

member including fixing of required

materials,scaffolding, labour etc complete as directed

by Engineer incharge.

Providing, Laying and Interloacking

100mm/150mm/200mm Masonary work using Aerated

light weight concrete block (AAC) having crushing

strength not less than 35 kg/sqcm for Foundation and

91 upto plinth level, using Ready Mix bonding material as a 35.82 Cum 5465.43

best and approved quality of adhesive mortar suitable

with layer of 4 mm thick laying with using of thread

towel tools, finishing joint, surface, reuire scafolding etc

complete by Engineer Incharge.

Providing & laying controlled cement concrete M250

for curing complete including cost of form work but

excluding cost of reinforcement for reinforced conrete

work in fins/wall for all floor.

Providing and laying Controlled cement concrete M-250

and curing complete including the cost of form work

93 but excluding the cost of reinforcement for reinforced 0.57 Cum 5298.36

concrete work in Wall caps / Coping.

Providing and fixing M.S. grills / Gates of required

pattern to brick walls / Columns prepared with M.S.

flats, angles, Square / round bars, square pipes, at

94 required spacings with necessary hold fasts as per 504.00 kg 162.86

detailed drawingand fixing brick wall / coping / columns

etc. complete including painting two coat & applying

primer coat.(A) Ornamental Grill

Item No. Item Description Quantities Unit Amount

Providing & fixing Razor coil wire fencing having

diameter of 0.75 mt including using of M.S angle

45x45x6mm as per detail drawing, fixing in cement

95 concrete M-250 etc completed with one coat of primer 98.98 Rmt 808.00

& two coats of oil paint to M.S angle, including concrete

cutting in existing compound wall with breaker, fixing of

MS angle etc. complete as directed by Engineer in

Clearing and grubbing road land including uprooting

rank vegetation grass bushes,shrubs,sapling and trees

96 girth up to 300 mm removal of stumps of trees cut 0.06 Hec 28455.03

earlier and disposal of unserviceable materials (C) By

mechanical means in area of light jungle.

Earthwork for embankment including breaking clods,

dressing with all lead and lift (excluding watering and

consolidation)(E) From Borrow area within 3.0 Km. lead

Rolling of earthwork in layers with power roller including

filling in depressions which occur during the process

including Watering of earth work as directed by

Engineer incharge.

Box cutting the road surface to proper slope and

camber for making a base for road work including

99 removing the excavated stuff with desposing on the 34.42 Cum 109.24

road side slope as directed up to 50 mt. Lead

Providing and and laying controlled cement concrete

M250 and curing etc complete including the cost of

100 form work but excluding the cost of reinforcement for 25.82 Cum 4778.73

R.C.C. work for internal road etc copmlete.

Excavation for foundation for depth from 3.0 m to 5.0 m

including sorting out and stacking of useful materials

and disposing off the excavated stuff as directed upto

50 Meter lead.(C) Hard Murrum

Providing and laying cement concrete flooring M150

laid in one layer and finished with a floating coat of

neat cement.(B) 50mm thick. (upto 10 ton)

Providing cement vata (10cm x 10cm size) quarter

round in cement mortar 1:1 including neat cement

finishing, watering etc complete as directed by Engineer

Item No. Item Description Quantities Unit Amount

Providing and fixing Fiber Reinforcemen Concrete

(FRC) Manhole cover of heavy Duty of load capacity

104 upto 35 Tons including frame etc complete as directed 6.00 No 2525.00

by Engineer incharge. Size: 0.60m x 0.60m

Providing and fixing cast iron steps of size 500mm

105 x 150mm x 22.5mm and painting with two coats of Anti- 24.00 No 207.66

corrosive paint etc complete.

Constructing Manhole with R.C.C. top slab in 1:2:4 mix

(1-cement :2-coarse sand : 4-graded stone

aggregate 20mm nominal size) foundation concrete

1:3:6 mix (1- cement : 3- coarse sand :6-Brick bats 40 +

50mm size) inside plastering 15mm thick with Cement

Mortar 1:5 (1-Cement : 5-coarse sand) finished with

a floating coat of neat cement and making channels

in cement concrete 1:2:4 mix (1-Cement :2-Coarse

sand :4-stone aggregate 20mm nominal size)

finished smooth complete including curing and

106 festing (i) Inside size 900mm x 1200mm and 1.5M. 2.00 No 23470.48

deep including C.I. cover with frame size 560mm

diameter total weight of cover and frame to be not less

than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame

64 Kg.)(A) With 230mm thick walls of brick

msonry using brick having crushing strength not

less than 35Kg. / Sq.cm. in Cement Mortar 1:5

(1- Cement: 5-Coarse sand) (3) C type depth

Metre for 150mm diameter sewer.

Providing and laying Cement concrete M150 bedding

for stoneware pipes of following internal diameters with

107 necessary formwork and curing complete. (A) 100 mm 10.00 Rmt 127.16

dia. (112 mm Ave. bed thickness)

Providing & laying controlled cement concrete M250

and curing complete including the cost of fromwork and

excluding the cost of reinforcement for reinforced

concrete work in Wall/Shear Wall.

Providing and laying Water proof white glazed tiles

mm. Thick in flooring treads of steps and landings laid

109 on a Bed of 12 mm. Thick cement mortar 1:3 (1 cement 50.67 Sqm 963.12

: 3 coarse sand) finished with flush pointing in white

Providing and laying cement concrete flooring M150

laid in one layer and finished with a floating coat of neat

110 cement with mixing water proofing material in Cement 34.30 Sqm 301.67

concrete in mix proportion recommended by the

manufacturers. (A) 40mm thick.

Providing and fixing the P.V.C. rain water out let pipe of

I.S.I. Mark as per instruction of Engineer in charge &

111 approved make with necessary bend, plug, jali, clamps 5.00 Rmt 90.90

etc complete. 110 mm dia.

Item No. Item Description Quantities Unit Amount

Drilling of 250 mm dia. bore well in all strata including

dual over burden strata by Combination DR / DTH rig

112 including lowering 200 mm dia MS ERW pipes in bore 20.00 Rmt 1270.58

hole as suggested by Hydrologist.

Drilling of 300 / 315mmdia. bore in all strata including

dual over burden strata by combination DR/DTH rig

including lowering of 204mm dia UPVC/225/250mm

dia.PVC/MSERWcasingpipesup 200 mm /225/250mm

dia.PVC/MS ERW casing pipes up to required depth

113 and further drilling of 200mm dia. bore hole in all types 300.00 Rmt 549.44

of Alluvial Rocky strata formation by DTH ring including

flush in bore hole by air compressor and measuring of

yield of bore by V notch and fixing of bore cap etc.

Supply of clay ball of size ranging from 25 mm to

114 mm made from stickly clay at site of work as certified by 40.00 Cum 758.51

supply and delivery of ISI marked ERW MS pipes

conforming to IS: 4270/2001 with latest amendment (a)

200 mm dia. (Minimum 6.00 mm thick)

Supply of 200mm dia & 6 mm thick ERW slotted pipe

having stainer size 100 mm X 4 mm.

Providing and Jointing ERW blank pipes or slotted

pipes by soldering including cost of all required jointing

117 materials, clamps sets etc with cutting, grinding etc 140.00 Rmt 25.25

complete as directed by Engineer incharge.

Supply of best quality of well sorted Sevaliya gravel of

size ranging from 4 mm to 6 mm.

Providing and fixing E.R.W. Bail plug of length

119 meter made from MS medium class pipe as per IS 2.00 Each 851.04

suitable for 200 mm dia pipe.

Supplying & erecting Heavy duty clamp made from 4" x

120 1.5" iron strip suitable for column pipe 1.5" to 2" length. 2.00 Each 212.10

(B) 50mm(2") dia pipe

Supplying & erecting G.l. bend for pipe connections

suitable for (D) 50 mm(2")

Supplying, & erecting C.I. swing, check type non-return

122 (Reflux) Valve -ISI marked suitable for following size (A) 2.00 Each 1201.90

Charges for development of bore by giving air with

compressor for requirement as per site situation {600

CFM / 150 PSI upto the any depth, minimum 6 hours}

Item No. Item Description Quantities Unit Amount

Supplying submersible pump set for bore of 150 mm.

dia.or more having 3 phase motor capacity 10 H.P. and

124 having (12 Stage) 350 L.P.M. discharge at the head 2.00 Each 42662.40

about 100 mtrs. suitable for 50 mm dia. Delivery pipe

Supplying & erecting approved make 3 phase motor

control cubical panel made from16 G. CRCA sheet duly

painted with epoxy power painted inside and outside

with hinged doors and locking arrangement, consisting

of suitable size of ON- OFF isolator (AC - 3/23 duty)

main fuses, single phasing preventor cum water level.

Guard (Complete unit), Toggle switch to by pass Single

phase preventer cum WLG, indicating lamps for R- Y- B

phases, over load relay, Automatic water level

125 controller, Ammeter & Voltmeter each with two way 2.00 Each 16053.95

selector switch incoming wires duly socket Crimped,

Panel to be erected on angle iron frame grouted on wall

as directed. Star Delta & main contactor, overload relay,

thermal / Electronic Star delta cutoff timer, start - stop

push buttons. The isolator overload relay & contactors

of L& T, Siemens or Cuttler Hamer make only. Panel to

be erected on angle iron frame ground on wall. (B) S/D

Lowering of submersible motor pump set complete with

required. Nos. and size of casing pipes erected by

means of proper chainpulley block & pipe wrenches

126 after checking of threads of each pipe with coupling to 1.00 Job 3030.00

take the load of the pump set and pipe assembly filled

up with water. (B) Above 60 mtrs. and Up to 120 mtrs.

Providing and erecting ISI marked PVC insulated PVC

Sheathed Flat flexible Submersible copper cable

approved make of following Size. (C) 3 Core x 4 Sq.

Supplying ISI Marked (Embossed) following size of

Heavy duty "C" Class G.I. Pipe & erecting etc complete

128 as per instruction of Engineer in charge & approved 100.00 Rmt 418.14

make with necessary plumbing as desired. (D) 50 mm

Supplying and erecting with leak proof materials, M.S.

Heavy duty ISI marked coupling having threads of

129 TPI/11 TPI suitable for 'C' class pipe to take load of 90.00 Each 107.06

pump and pipe assembly of following size and TPI. (C)

50 mm(2") dia. pipe 8 TPI

Add cost of leak proof complete welding surrounding

130 pipe and coupling for use as column pipe for following 90.00 Each 70.70

Cutting the heavy duty pipe and threading one end of

pipe with 8 TPI / 11 TPI as per requirement and

including to and fro charges (B) 50mm (2") dia pipe

Item No. Item Description Quantities Unit Amount

Plantation of trees in soil incl digging 45 x 45 x 45cm

size pits, preparing soil, providing and mixing organic

132 fertilizers, watering planting and filling the pits as per 15.00 No 35.35

direction including etc complete.

Providing Tree Plants having minimum 1.00 mt

Height and healthy growth of various kinds as like

133 Peltophorum, Gulmohar, Karanj, Ambala ,Rain tree 15.00 No 27.27

Saptaparni, Cherry, Cryjeliya , Spethodiya, Paras

Pipala, Garmalo, Neem , Borsalli, Kadam Buch,

Maintanance of Planted tree upto Two Year incl

times Watering, at regular interval digging pits,trimmimg

134 applying Fertilizer insecticides . pesticides and 15.00 No 358.55

Pesticides and replacing plants if necessary etc

complete for raising of Plants weeding or soil working

Providing and fixing TREE GUARD 2.00 mt. long & of

600mm dia square mesh of 50 X 50 mm and M.S. Flat

135 of 25mm x 5 mm vertical support and three rings of 20 15.00 No 2494.70

x 3 mm flat, fixing on site in M150 etc complete as

directed by Engineer in charge.

Providing and fixing pre-cast concrete kerb stone of

gray cement based concrete block 30cm length,30cm

height and 15cm thick of M250 grade concret as per

136 approved design and including excavation for fixing in 44.80 Rmt 400.87

proper line and level,filling the joint with C:M 1:3

(1cement:3fine sand) etc complete. (upto 10 ton)

Painting lines, dashes, arrows, letters, etc. on roads, air

fields and like in two coats with road marking paint

137 Brushing including cleaning the surface of all dirt, dust 26.88 Sqm 130.28

and other foreign matter. (1) Over 10 c.m. in width

Providing and Fixing on site sandwich type colour

granite stone decorative seating highback 0.75 mtr

arrangement having size 2.5 X 0.6 mtr and 0.45 mtr

hight and 20mm thick both side polished granite stone

138 including, cutting, fixing, jointing with white cement, 4.00 No 8585.00

colour pigment, moulding of edge and finishing with

Foundation base etc detailed drawing as directed by

Engineer incharge.

Excavation for foundation upto1.50 MT depth including

sorting out and stacking of useful materials and

disposing the excavated stuff up to 50 mt lead. ( B )

Loose or soft soil

15mm the cement plaster in single coat on fair side of

brick / concrete wall for interior plastering up to floor two

140 level finished even and smooth in C M 1:3 ( 1 cement : 5.47 Sqm 161.20

3 coarse sand) including finishing with a a floating coat

of neat cement slurry complete. For Ground floor

Item No. Item Description Quantities Unit Amount

Supplying of crushed stone aggregates Chippings etc of

hard stone of 25 to 40 mm nominal size free of

141 disintegrated pieces. Deleterious and organic matter 0.86 Cum 782.18

(for bitumen surface dressing etc.) and gradings with all

Drilling of 200 / 215 mm dia. bore hole in overburden

strata by DTH rig up to required depth including fixing of

175 / 180 dia MS ERW / PVC casing pipe & further

drilling of 165 mm dia. bore hole in hard rock (trap etc.)

142 strata by DTH drilling method up to total depth of 300 30.00 Rmt 266.64

meters including measuring the yield by V notch and

flushing of bore etc. complete in all districts of Zone V.(

Casing up to 12 Mts.)

Manufacture, supply & delivery of ISI marked UPVC

Casing pipe (IS 12818 with latest amendment. (Rates

143 are exclusive of GST)175.00 mm nominal dia. " CS " 20.00 Rmt 1064.54

Type including lowering etc complete (Rs. 906 + 148 =

Providing and fixing Box type wooden Wardrobe

mm deep with 18 mm thick BWP shutter as per detailed

drawing of each room including facility of Pull out

Drawer, Shelf, Shelf Hanger, Drawer, Jwellery Drawer,

laguage space, inside cover with liner and outside

144 finishwith 1 mm thick laminates including edge covering 44.10 Sqm 9195.62

with Indian teakwood patti with wooden polish groov

type handle using all necessary material etc complete

as directed by Engineer incharge. (Measure Front

Elevation Area)

Providing and Fixing of 32 mm dia Rod SS 304 grade

including fixing with SS hook 100 mm long etc using

145 with all necessary materials like Clamp, screw, wire 52.08 Rmt 726.61

nail, etc as directed by Engineer incharge.

ABC Type DCP Extinguishers 6 Kg ( MAKE-KANEX,

ATASEE, SAFEX )

4.2 Kg CO2 Capacity ( MAKE-KANEX, ATASEE,

Point wiring for FAN with 2-1.5 sq.mm & earth wire of

1.5 sq.mm (Green) both are of .ISI marked 1.1 kV

Grade FRLS PVC insulated multi strand copper wires

up to 10 mtr length, in below type of pipe erected with

6A Modular type switch and hum free EME step type

electronic fan regulator mounted and accessories with

earth continuity of following type erected on PVC /

148 Metallic/Wooden box, single mounting base frame 20.00 Pts. 626.20

covered with textured/metallic/white front plate

modules erected on / in wall / ceiling as per pipe

erected. with necessary ceiling rose / H.D.Connector as

directed.(f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling complete

Item No. Item Description Quantities Unit Amount

Point wiring for Light / Bell with 2-1.5 sq.mm & earth

wire of 1.5 sq.mm (Green) both are of ISI marked

kV grade FRLS PVC insulated multi strand copper

wires up to 10 mtr length , in below type of pipe erected

with 6A Modular type switch / bell push & accessories

and earth continuity of following type, erected on PVC /

149 Metallic/Wooden box, single mounting base frame 70.00 Pts. 582.77

covered with textured/metallic/white front plate modules

erected on / in wall / ceiling as per pipe erected, with

necessary Lamp holder/ceiling rose / H.D.Connector as

directed. (f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling complete

Point wiring for on board Looped Plug with 6A Modular

type switch & 5 pin socket erected on PVC /

150 Metallic/Wooden box, single mounting base frame 56.00 Pts. 309.06

covered with textured / metallic/white front plate

modules erected on / in wall / ceiling with following

type accessories cat lll

Providing following type of Modular Type Accessories

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

151 metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge.

(10) 6/16Amp. Universal socket Cat.III 44.00 Ea 199.98

(9) 16 Amp. SP one way switch Cat.III 44.00 Ea 180.79

Providing and erecting Mains with 1.1 KV grade FRLS

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected concealed

in /flushed on wall/ceiling, with 1.5 sq. mm copper

152 conductor FRLS PVC insulated stranded wire of green 896.00 Mtr. 104.03

colour for earth continuity of following size Cat.III (A)

with medium class Rigid PVC pipe and accessories (b)

2 wire 2.5 sq. mm

Providing and erecting ISI mark Medium class RIGID

PVC PIPES of following size complete to be erected

153 on/in wall or ceiling erected with necessary PVC fittings

& Junction boxes fixed with adhesive solution & Clamps

with following dia of pipes, in approved manner as

Item No. Item Description Quantities Unit Amount

providing and erecting Mains with 1.1 kV grade FRLS

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected in / on wall /

154 ceiling with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth

continuity of following size (A) with medium class Rigid

PVC pipe and accessories

(a) 2 wire 4 sq. mm 256.00 Mtr. 140.39

(i) 4 wire 10 sq. mm(use earth wire of 4 sq.mm ) 80.00 Mtr. 532.27

providing and erecting Mains with ISI marked, 1.5kV

grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms

155 to IS 694, IEC - 227 erected in existing pipe of

following size (Specifically for control panel, relays,

power switchgears, motor starters & control wiring) with

required size of copper lugs, nuts and bolts if required.

(b) One wire 1.50 sq. mm 6.00 Mtr. 22.22

(f) One wire 10.00 sq. mm 18.00 Mtr. 115.14

Supplying and erecting Flexible PVC insulated multi

strand multi core 1.1 kV grade ISI marked copper wires

156 of following size to be erected as directed. e) 1.50 33.00 Mtr. 58.58

Sq.mm 3 core round PVC sheathed

Decorative call bell Ting-tong box type 250 volts

complete erected

Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be

made of thick sheet Steel conforming to IS: 513/CRCA/

aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company

mark/name 160V to 270V, Power Factor more than

0.95, THD < 15%,CCT 3000 K to 6500K, Luminaire

158 efficacy> 85 lumens/watt ,LED LED driver efficiency > 26.00 Ea 535.30

85 %( fitting required LM-79 & LM-80

Certificates)(NOTE: Below description have shown

ranges of Wattage capacity of LED fittings.The

Engineer incharge may select any wattage capacity

between the ranges shown.)(A) Tube Light with integral

driver (v) 36-40 Watts, Surge-2 kV, IP-20, conventional

Item No. Item Description Quantities Unit Amount

Supplying and erecting led lamps with following wattage

capacity of 220 to 240 voltage, minimum 15000 burning

hours life, 500 V in built-surge protection,Polycarbonate

159 diffuser, mounting suitable for E14 / E27 / B22 lamp 32.00 Ea 112.11

holders, pf >= 0.5 (A) LED Lamps integral type, with PC

diffuser suitable LAMP holder (ii) 5 to 8 watts cat

Supplying and erecting LED street light / Flood light

fittings with High power White LEDs wattage of 3 Watt

and above assembled on single MCPCB, efficiency

more than 130 lm/w and corrosion free High pressure

die cast aluminum housing with smooth finish powder

coated and heat sink extruded aluminium with diffuser

and Polycarbonate optics/ lenses, with toughened glass

with company mark/name engraved or embossed

to 270 V,Power Factor more than 0.95, THD < 10 %,

CCT 3000 K to 5700K,Uniformity ratio >0.45,

160 Luminaire efficacy> 100 lumens/watt . LED driver 9.00 Ea 4248.06

efficiency > 85 %.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have shown

ranges of Wattage capacity of LED fittings.The

Engineer incharge may select any wattage capacity

between the ranges shown.) (A) Street Light (IP-65),

Surge protection -4KV integral and ,Light must have

440VAC line supply with over-voltage protection. (ii)

above 48 to 59 Watts cat lll

Providing and erecting Approved make Four pole

moulded case circuit breaker having breaking capacity

ICU of 25 KA. at 415 V,having normal current rating up

to 25 A to 100A. with Fixed thermal & magnetic release

161 suitable to work on A.C. supply 50 Hz. with all internal 1.00 Ea 6790.23

connections, spreader tinned copper & complete

erected in existing 16 G.M.S. housing.

ICS=100% of ICU only Cat III

Supplying and erecting triple pole & neutral 440V/ 500V

panel mounting Aluminium Busbars with four equal

Nos. of bus having current density not more than

Amp. / sq.mm (Rated current / cross section area) duly

wrapped with colour insulating tape for phase sequence

162 of following current carrying capacity, erected with 0.50 Rn.mtr 660.54

necessary bus bar supports /insulators, main cable

socket to each busbar,erected in existing cubical panel

with necessary connections. (A) Suitable for 100 Amp.

Item No. Item Description Quantities Unit Amount

Supplying & erecting approved make Digital time switch

having lithium cell 6 years operative and operate

battery backup 1 channel day clock with 14 memory

programme, suitable to operate on 240V + 5%, 16A

with, floating contacts Minimum switching setup time

163 minimum & LCD display. Also comprised permanent 1.00 Ea 3168.37

ON/OFF switching. Programming switches & housed in

fire proof thermoplastic enclosure & transparent cover

erected as required with necessary connection erected

Supplying & erecting power contactor ,AC3 duty for

164 time switch complete erected as per direction Cat III D) 1.00 Ea 2782.55

4 pole 440V 40 Amp.

Supplying and erecting approved make suitable panel

165 indicator LED type lamp, lens cover, complete erected 3.00 Ea 43.43

with necessary connections.

providing and erecting Miniature circuit breaker single

pole 0.5A to 2A system and having breaking capacity

166 10 KA to be erected in existing box. confirming to IS 9.00 Ea 297.95

8828/1996 with ISI Mark cat lll

providing and erecting Miniature circuit breaker single

pole 6A to 25A suitable to operate on 240 V A.C.

167 system and having breaking capacity 10 KA to be 72.00 Ea 123.22

erected in existing box. confirming to IS 8828/1996 with

ISI Mark cat lll

Providing & erecting 240 V MCB double pole switch for

motor & inductive load (C Curve) having 10 KA

168 breaking capacity & confirms to IS : 8828 in existing box 13.00 Ea 362.59

having following capacity (B) 40 Amp. Cat.III

Providing & erecting 415 V MCB Four Pole for Motor &

Inductive Load (C Curve) having 10KA breaking

169 capacity & confirms to IS :8828 in existing box having 6.00 Ea 811.03

following capacity (c)63 Amp. Cat lll

Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to

170 IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be used of

same company of MCB to be used) suitable for

(B) three phase incoming and single phase horizontal

type outgoing Per phase isolation type (PPI) (b) sheet 4.00 Ea 3412.79

steel double door (iii)8 way

providing and erecting Approved make RCCBs

conforming to IS: 12640 and having sensitivity of 30 mA

and Short Circuit withstand capacity of 10 KA and

suitable for operation on single phase 240 V,50Hz.

171 having characteristic of quick action & tripping with all 12.00 Ea 2458.34

advance feature & do not incorporate any electronic

component. for following Max. rating erected as

directed (ii) 40Amps. DP cat lll

Item No. Item Description Quantities Unit Amount

Providing and erecting Approved make RCCBs

conforming to IS: 12640 and having sensitivity of 30 mA

and Short Circuit withstand capacity of 10 KA and

suitable for operation on 3 phase and neutral

172 415V,50Hz. having characteristic of quick action & 2.00 Ea 2900.72

tripping with all advance feature & do not incorporate

any electronic component for following Max. rating

erected as directed. (ii) 40Amps. FP cat lll

Providing and erecting HOT deep Galvanised iron

strip/wire 4.064mm to 1.626mm.

Supplying & erecting in earthpit of minimum bore dia.

225mm size approved make Safe Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-

1987 made of corrosion free hot dipped G.I.Pipes

having Outer pipe dia of 80 mm having 80-200 Micron

galvanising, Inner pipe dia of 40 mm having 200-250

Micron galvanising, connection terminal dia of 14 mm

with constant ohmic value surrounded by highly

conductive compound with high charge dissipation

suitable for following type of applications with chamber

and heavy duty cover (A)(approved make OEM has to

submit test certificate including value of earth

resistance of installation duly stamped and signed by

174 agency and officer Incharge has to ensure the value of 5.00 Ea 5842.85

earthing resistane mentioned in test Certificate) &

having back filling compound of (B) Inner chemical

(CCM Compound)- Resistivity:- 0.2 ohm / meter testing

as per IEC 62561-2017, Voltage drop:- < 1 volt at no

load & dry form, Sulphar content:- <2%(C) Back fill

Compound :- Earthing compound should be capable to

retain moisture for long time Necessary test report

must be submitted by Agency.Length of Pipe -

MtrBack filling compound - 1 Nos. of Bag of 15 Kgs.[A]

For electrical installation up to 440 VLength of Pipe -

MtrBack filling compound - 1 Nos. of Bag of 15 Kgs.

Providing and erecting FRLS-XLPE (IS:7098)(I)-88 ISI

armoured cable multistrand / Solid Aluminium

175 conductor for 1.1 kV. to be laid on wall with necessary

clamps or in existing trench / pipe of following size of

(B) 4 core 6 Sq. mm 200.00 Mtr 151.50

Making trench in Hard Murrum / Tar Road of suitable

width of 90 cm or required depth for laying any size of

176 cable or locating the fault all over the run and back 80.00 Mtr. 74.74

filling the same and making the surface as normal

Providing & laying approved make ISI marked HDPE

6Kg / cm2 (Class-3) as per IS:4984:1995 PE-80 to be

177 erected at road crossing on or floor as directed for

laying of cable. The pipes as following size of dia &

weight per 6 mtr.

(A) 40 mm inner Dia. 88.00 Mtr. 108.07

Providing and, fixing heavy duty flange type brass cable

gland with rubber ring for PVC insulated armoured

178 cable complete with out going tails, insulating tape etc 18.00 Ea 38.38

for following size of cables.(b) 2 to 4 core 6 Sq. mm

Item No. Item Description Quantities Unit Amount

Solder less crimping type Aluminium lugs conforming to

IS suitable for cable of following size evenly crimped

179 with high pressure tool & connected to switchgear

terminals with brass/cadmium plated nut bolts in an

approved manner.

Providing & erecting Approved make Power Saving 45 -

50 Watt Ceiling Fan with double ball bearing ISI mark

with Condenser 230 volt A.C. 50 Hz 1200 mm sweep

180 complete having 3blades with aluminium blades with , 20.00 Ea 1948.29

canopy & 30 cm. down rod erected with earthing.(Make

shall be approved by Engineer in charge))

Supplying and erecting 19 / 20 mm. nominal bore

Medium Class M.S. Pipe down rod erected duly painted

for fan complete with proper insulation without leakage

Supplying & erecting fan hook box of 10 mm M.S.

round bar bounded to the RCC bars up to 50mm length

182 each side and pierced through a 16 Gauge M.S. box / 20.00 Ea 108.07

Heavy Duty PVC box complete erected concealed in

Ceiling with necessary finishing.

Providing 2.5mm.thick laminated acrylic sheet to cover

the fan hook or Fan box.

Supplying & erecting approved make low noise

decorative exhaust fan having square frame ABS body

with inbuilt lowers & square frame. 200mm with

Supplying and erecting approved make Octagonal pole

made from HR sheet steel. The pole should be made

as per IS. and shall be coated with hot dip galvanizing

as per IS 2629/2633/4759, suitable suspend local wind

speed with integral Junction box consist of terminal

plate of min 6mm Hylam sheet, standard profile

35mmX7.5mm Din-Rail for MCB Mounting, stud type

185 terminal and arrangement for cable termination to be 3.00 Ea. 7561.87

erected With Suitable foundation (Included) as per

details given by manufacturer considering site

requirement.(C) 5 Mtr. Long 70 mm Top X 130 mm

bottom dia, 3 mm thickness with

200mmX200mmX12mm base plate, 4-M16 Bolts and

600mm long with necessary G.I. J Bolts .Approx Pole

Item No. Item Description Quantities Unit Amount

Providing and erecting street light pole bracket

comprising main B Class GI pipe of 4.2 cm/require

outside dia. complete with suitable B Class G.I sleeve

tubing of approx. 45cms.length and suitable for

mm / 80mm. / require size pole top having sufficient

fasteners for fixing the brackets and having spread of

186 mtr. length with suitable rise as per site condition & 3.00 Ea. 614.08

suitable welded stiffener reducer and nipple with check

nut complete painted with one coat of Red oxide / PU

base primer and two coats of Aluminium / PU paint.

paint with following nos of arms.[A] Single Arm bracket

Supplying & erecting IP 55 grade following size section

pillar fabricated from joint less M.S. Sheet with angle

iron legs made from jointless M.S. Angle with cable

clamps to be buried in ground to have appropriate

187 erection to work uniform until erected with cement

concrete foundation and 45 cm high bricks work

finishing with plaster etc. hinged double door internally

supported on both side,

with internal and outside looking arrangement with look

and keys in duplicate 35 x 35 x 5 mm M.S. Angle of

Two Nos. one is welded and other with nut and bolt for

erecting Bakelite sheet. Painting the Section Pillar

inside and out side with three tank powder coated paint.

section pillar roof should be without joint with water 1.00 Ea 3595.60

leakage proof & tested as per IP 55 test & followed by

IS 2147 of 1962 (B) 75 X 60 X 45 cm section pillar

fabricated from 16 Gauge MS Sheet with angle iron

legs 45 cm long made from 35 X 35 X 5 mm thick MS

Supplying and erecting HYLAM sheet on existing angle

iron frame.for following thickness (A) 2mm

Providing & erecting open well horizontal mono block

pump set with cast iron body, complete for three phase

189 submersible motor having[B] For 2 HP 3 phase open 1.00 Ea 11807.91

well horizontal mono block pump set suitable for

LPM @ 25 mtr head suitable for 50 mm dia delivery

Supplying & erecting approved make motor control

cubical panel (Direct - on - line) made from 16 G. CRCA

sheet duly epoxy powder painted inside and outside

with hinged doors and locking, arrangement consisting

of suitable size of ON- OFF isolator (AC - 3/23duty)

main fuses, single phasing preventer, indicating lamps

for R- Y - B phases, overload relay, Automatic water

190 level controller, Ammeter, Voltmeter each with two way 1.00 Ea 7722.46

selector switch incoming, wires duly socket crimped,

main contactor & overload relay, start - stop push

buttons, to be erected on angle iron frame grouted on

wall as directed. The isolator, overload relay &

contactors will be of L & T, Siemens or BCH make only.

(A) DOL up to 5.0 H.P.

Item No. Item Description Quantities Unit Amount

Providing and erecting ISI marked PVC insulated PVC

Sheathed Flat flexible Submersible copper cable

approved make of following Size. (C) 3 Core x 4 Sq.

Supplying & erecting approved make SMC press

moulded composite FRP. loop-in, loop-out approx.

2mm thick box complete with Bakelite connector strip

5way(3P+N+E),DIN rail for mounting mob & hinged

192 doors as per requirement having locking arrangements 6.00 Ea 476.72

with mounting clamp with nuts, bolts & washers suitable

for erection on pole with cable clamps& earth bolt of

following size of box. (C)150mm x 125mm x 100mm

Supplying and erecting B class galvanised iron pipe

mm outside dia 45 cm long duly welded on 20 cm x

193 cm x 3 mm thick M.S. base plate, erected on wall or 6.00 Ea 343.40

corner for mounting street light luminaire with necessary

hardware materials duly painted.

I/We am/are willing to carry out the work at…% above/below percent(Should be written in figures and words) of the

estimated rate mentioned above. Amount of my /our tender works out as under.

(A) Estimated amount put to tender Estimated amount put to tender

(B) Deduct………% below Add………% below

(Rs. in Words __________________Only). (Rs. in Words __________________Only).

(* Please strike out whichever is not applicable).

1. The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-

In-Charge for which no extra payment shall be made.

2. The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3. GST and Income tax TDS will be deducted at a source while making payments of bills.

4. In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-

10/2017 Cement Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where

there is a change as per actual mix design the cost of difference of cement consumption have been deducted

from the rate of original item at the rate of input rate mentioned in all the tender.

Dated Signature of Deputy Executive Engineer Executive Engineer

the Contractor. R & B (P) Sub Division R & B (P) Division

Bhachau-Kutch Bhuj-Kutch