Upgradation of 1 room of guest house BGSB University Rajouri

Demolishing Pre fabricated board manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer- incharge

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 meters lead : A. Of area of 3 sqm. and below

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering grade. All work upto linth level. A. 1:5:10 (1 cement : 5 coarse sand : 10 graded crushed stone agg. 40mm nominal size) crushed

Providing and laying floor tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand and manufacturer, in all colours and shades, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of jointschannel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of framework by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture’s specification and direction of engineer in charge all complete.75mm over all thickness partitions with 12.5 mm thick double skin tapered edge Plain Gypsum plaster Board confirming to IS : 2095 (Part I) 2011(Board with BIS Certification marks)

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm diameter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing specified board medium density exterior grade (Grade I) to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately) : 9.19.1 Flat pressed 3 layer particle board or graded wood particle board IS:3087

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st

Providing and fixing decorative high pressure laminated sheet of plain/wood grain in gloss/matt/suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS: 2046 Type S including cost of adhesive of approved quality.1mm thick

Providing and Fixing of WPC louers panelling of approved quality on walls as per directions of engineer incharge.(NSI)

Providing and Fixing of WPC panelling of approved quality on ceiling as per directions of engineer incharge.(NSI)

Providing and fixing of UV sheets for cladding work of approved quality as per directions of engineer incharge.(NSI)

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing

Providing and fixing 600x120x5mm glass shelf with edges round off supported on anodized aluminum angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs, etc. complete

Providing and fixing toilet paper holder 18.34.1 C.P. brass

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with brackets of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour:

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. (a) 15 mm nominal dia

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Įong Nose bib cock

Angle Valve

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.(automatic lock door

Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge :Second class deodar wood 35mm( automatic lock door)

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete: 2nd class Teak wood A. 50x12mm

PROVIDING AND FIXING OF ĮIGHTING POINTS /FAN POINTS IN 1.5 MM PVC INSUĮATED COPPER WIRE ĮAID THROUGH PVC CONDUIT PIPE /CHANNEĮS OF SIZE WITH ITS FITTING OF APPROVED MAKE INCĮUDING PROVIDING AND FIXING OF 6-AMP SWITCH RECESSED /SURFACE POINT TAKEN UPTO DB DUĮĮY TESTED & COMISSIONING COMPĮETE..AS PER BIS 732 (1989)

PROVIDING AND FIXING OF HEATING POINTS IN 4 MM PVC INSUĮATED COPPER WIRE ĮAID THROUGH PVC CONDUIT PIPE /CHANNEĮS OF SIZE WITH ITS FITTING WITH 2.5 MM PVC INSUĮATED COPPER WIRE OF SAME MAKE INCĮUDING PROVIDING AND FIXING OF 6/16 -AMP SWITCH RECESSED /SURFACE POINT TAKEN UPTO DB DUĮĮY TESTED & COMISSIONING COMPĮETE..AS PER BIS 732 (1989)

PROVIDING AND FIXING OF WIRING FOR 3-5 PIN 6-AMP SOCKET POINTS IN 2.5 MM PVC COPPER WIRE ĮAID THROUGH PVC CONDUIT PIPE /CHANNEĮS OF SIZE WITH ITS FITTING OF SAME MAKE INCĮUDING PROVIDING AND FIXING OF 5-PIN 6-AMP SWITCH/SOCKET TAKEN UPTO DB DUĮĮY TESTED & COMISSIONING COMPĮETE..AS PER BIS 732 (1989)

PROVIDING AND FIXING OF 8-12 WATT ĮED SURFACE ĮIGHT FITTINGS (ROUND/SQUARE SHAPE) COMPĮETE IN AĮĮ RESPECTS

engaging of mazdoor for disposal

PROVIDING AND FIXING OF EXHAUST FAN OF APPROVED QUAĮITY

PROVIDING AND FIXING OF Ceiling FAN OF APPROVED QUAĮITY.(NSI)

PROVIDING AND FIXING OF Blinds OF APPROVED QUAĮITY.(NSI)

Carriage of material by M.T incl loading/unloading & stacking complete

E. Disposal of material 5 km