PROVN OF WET WEATHER PROTECTION SHELTER AT THE MAIN GATE FOR SECURITY PERSONNEL AT ICG LAND MUNDRA

Amount

Excavating over areas, n exc 1.5 m deep and getting out in soft / loose soil

Excavating over areas, exc 1.5 m and n. exc 3.00 m deep and getting out in soft / loose soil

Excavation in trenches not exc 1.5 mtr wide and not exc 1.5 mtr in depth and getting out in in soft / loose soil all as specified and directed

Returning filling in including spreading ,levelling,watering and wall ramming in layers not exc 25cm in soft / loose soil complete all as specified and directed.

Removing excavated material (soils) n. exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point

M&L for cement concrete Type D2 1:4:8 (40 mm graded aggregate) in in foundations, filling and mass concrete.

M&L for reinforced cement concrete (design mix) M-30 (20mm graded aggregates ) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete etc complete all as specified and directed.

M&L for reinforced cement concrete (design mix) M-30 (20mm graded aggregates ) in Columns, pillars, piers, posts and struts etc complete all as specified and directed.

M&L for reinforced cement concrete (design mix) M-30 (20mm graded aggregates ) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like etc complete all as specified and directed.

M&L for reinforced cement concrete (design mix) M-30 (20mm graded aggregates ) in beams, cantilevers, bressumers, lintels over 1.5 clear span etc complete all as all as specified and directed.

Use & waste of formwork to sides of concrete foundations, rough finished surfaces of flat concrete, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, etc complete all as specified and directed.

Use & waste of formwork to rough finished surfaces of flat concrete, sides and soffits of floor or roof beams, beam haunchings, girders, bressumers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

Use & waste of formwork to rough finished surfaces of flat concrete,soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), etc complete all as specified and directed.

Use & waste of formwork to rough finished surfaces of concrete,square, rectangular or polygonal, sides of pillars, posts, struts, piers, columns and stanchions,etc complete all as specified and directed.

M & L for CRS bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, TMT bars,etc complete all as specified and directed.

M&L for CRS TMT bars 5mm and above upto and including 10mm dia in stirrups, spacers and binders cut to length bent to shape required, and binding with MS wire not less than 0.9mm dia complete all as specified and directed.

M&L for pre-cast cement concrete block masonry 1:5:8 (20mm graded aggregate) with solid blocks, exc. 10 cm in width and setting in cement mortar 1:6, complete

S&F aluminium composite panel of 4mm thick exterior grade in wall / column / ceiling with combination of aluminium skin material of 0.25mm thick (two or more metallic coloured coating sheet as directed) aluminium sheet of alloy grade 1100-H14 cover material, coated on external side with PVDF coating containing 70% resins for anti-fungal and anti bacterial properties and the center core shall be with natural polyethelene (HDPE) bonded to the aluminium skin on both side over aluminium frame of section 50 mm x 37 mm x 1.6 mm (16 gauge) fixed on the wall/ Ceiling. Cladding panel to be fixed with rawl plug and SS screw all as approved on walls and roof including necessary accessories, complete all as per manufacturer's instructions and as directed by Engr-in-charge

S&F Italian letters of height 450mm and 60mm thickness with LED dotted lights, fixed with SS screw on ACP cladding and providing polished plain acrylic sheet having thickness of 2mm over the letters all as directed by Engr-in-Charge.

S&F Coast Guard computerised printed logo of 600mm height, width upto 527 mm and 60mm thickness with LED dotted lights, fixed with SS screw on ACP cladding and providing polished plain acrylic sheet having thickness of 2mm over the logo all as directed by Engr-in-Charge.

M&L for sub main wiring with two run of 1.5 sqmm single core, PVC insulated, unsheathed multistranded copper FRLS cable 1100 volts conductor drawn through surface rigid PVC Conduit not less than 20 mm with all accessories and 1.5 sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable as earth continuity wire complete all as specified and directed. Note: Two runs of main cable, one run of earth wire and one run of PVC conduit will be measured as one unit for payment.

S & F recess mounted decorative ultra slim square profile LED light 15 watt , energy efficient , efficiency is greate than 100lm/watt , 6500K, , polycarbonate extruded body, including connection with flexible cable copper conductor three core of size 23/.2 mm upto ceiling rose/connector and making good of existing wall surface complete all as specified and directed by Engineer - in - Charge.

M & L for ceiling rose surface bakelite 3 terminals 63.5 x 17 mm.

S&F junction box with cover and outlet complete all as specified and directed.

Supply, laying, testing & commissioning of LT Cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables(heavy duty) with stranded aluminium conductor, 1100 volts grade, of cross sectional area 16 sq mm, 2.0 core all as directed.

Supplying & laying factory made unreinforced Precast concrete cover of class LV, type 1, flat, size 250 mm x 150 mm x40mm for protection for cable all as specified .

M&L for dry Sand filling in cable trenches for protection of cables with two layers below and above cable and punned down to specified thickness complete as directed. Note: Punned down thickness shall only be measured for payment.

S & F sheet metal enclosure for double door DB made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N, 4 ways, 415 Volts, ISI marked, 200 amps bus bar stove enamelled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed by Engineer - in - Charge.

Supply and fixing 240V 10KA 'C' curve miniature circuit breaker (MCB) of SP&N 32 Amp complete with connection, testing and commissioning.

Supply and fixing 240V 10KA 'C' curve miniature circuit breaker (MCB) of SP 6-32 Amp complete with connection, testing and commissioning.

Material and labour for earthing complete with galvanized earth plate electrode in 60 cm x 60 cmx 6 mm thick buried directly in ground vertically at a depth not less than 2.25 meter below ground level with top edge of earth plate at depth not less than 1.5 mtr below ground level connecting to and including GI wire 4.00 mm dia mm by means of GI bolts, nuts, check nuts and washer light grade, 15 mm dia GI protection pipe and connected to equipment, GI pipe medium grade 20 mm dia for watering and including funnel wire mesh, RCC pit cover and PCC 1:3:6 type C-2 including Rocksalt, charcoal, excavation and earth work disposal of surplus soil shown as plate No 3 of SSR Part - I 2009 and all as specified complete. Note : - The unit rate quoted shall deemed to have included for GI protection pipe, GI earth wire up to 7.5 mtr, GI water pipe, wire mesh , funnel , excavation, RCC pit cover complete.

SHREE BHANU ENTERPRISE