ADDN / ALTN TO DHOBI GHAT AT AF STN SURYALANKA

Amount

Taking down cement or cement lime plaster, any description, on brick or stone walls including racking out joints hacking for key scrubbing down with water etc. complete all as specified and as directed.

M&L for rendering 5mm thick on fair faces of concrete surfaces in cement mortar 1:3 in ceiling surface finished even and smooth with out using extra cement complete all as specified and as directed.

M&L for rendering 10mm thick on fair faces of brick or concrete surfaces in CM 1:6 finishing even and smooth with out using extra cement complete all as specified and as directed.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in two layers, first layer 10 mm thick in CM 1:6 and second layer 5 mm thick in CM 1:4 finishing fair and even mixed with WPC as per manufacturer's instructions complete all as specified and as directed. (Note : Supply of water proofing compound shall be measured and paid separately).

Supply only of integral water proofing compound of approved make complete all as specified and as directed.

Demolition of cement concrete in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and as directed.

Taking down chowkats or frames (without taking off shutters from the frame) not exceeding 1.5 sqm each and removing to store complete all as specified and as directed.

Taking down chowkats or frames (without taking off shutters from the frame) exceeding 1.5 sqm but not exceeding 4 Sqm each and removing to store complete all as specified and as directed.

M&L for Brick work with sub class 'B' bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed.

M&L for joint free non Skid ceramic coloured tiles (matt finish) 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in cement mortar mortar 1:6 complete all as specified and as directed.

M&L for 100 mm high skirting with joint free non Skid ceramic coloured tiles (matt finish) 7 to 8 mm thick high area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tile, laid over and including 10 mm thick backing coat in cement mortar mortar 1:4 complete all as specified and as directed.

M&L for 20-25 mm thick Kota stone slabs in floorings laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and laid over and including 20 mm thick cement screed bed in cement mortar 1:6, complete all as specified and as directed.

M&L for 20-25 mm thick Kota stone slab as in risers of steps, skirting, dado and pillar laid over and including 10 mm thick backing coat in cement mortar 1:4, and jointed grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for rounding to the edges of stone slabs one edge as in steps, cooking platform, and other similar situations complete all as specified and as directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and as directed.

Excavating in post holes (or similar holes) each not exceeding 0.5 Cum, getting out in soft / loose soil, and removing surplus soil to a distance not exceeding 50 m and making good surface complete all as specified and as directed.

Excavation in trenches, n.exc 1.50m wide and n.exc 1.50m in depth for foundations, etc. or for shafts, wells, manholes etc. n.exc 10sqm on plan and n.exc 1.50m depth and getting out in soft/loose soil complete all as specified and as directed.

M&L PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and as directed.

M&L PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and as directed.

S&F Rolled mild steel work conforming to Fe 290 Gde E-165 as in stanchions, posts, with flange plates, caps, bases, splices, angle brackets, cleats and other connections complete all as specified and as directed.

Rolled mild steel sections conforming to Fe 290 (Gde E-165 as in main and cross beams, hip and jack rafters; purlins where connected to common rafters fixed with angle cleats or other connecting plates complete all as specified and as directed.

M&L for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of Fe 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Hard core of gauge n.exc 63 mm , with broken stone or boulders , deposited, spread and leveled in layers n.exc 15 cm thick, watered and well rammed to a true surface complete all as specified and as directed.

M&L for 75mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregates as in sub base of floor complete all as specified and as directed.

M&L for 40 mm thick plain cement concrete type B- 1, 1:2:4 mix using 20mm graded stone aggregate as in floors , paths, pavings etc. surface finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 50 mm thick plain cement concrete type B- 1, 1:2:4 mix using 20mm graded stone aggregate as in floors , paths, pavings etc. surface finished even and smooth without using extra cement complete all as specified and as directed.

S&F for Pressed steel frames 105 x 60mm size for doors with one or more rebate including necessary fixing lugs, hinges, lock strike plate, etc., supplied and fixed complete all as specified and as directed.

M&L for Plain cement concrete 1:3:6 type C-0 using 12.5 mm graded stone aggregate for filling of hollow portions of door frames etc., complete all as specified and as directed.

S&F for 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

M&L for powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleats for fixing etc., complete all as specified and as directed.

S&F of powder coated anodised aluminium window and ventilator glazed shutters, side hung type without sash bars aluminium sections weighing 0.55 kg/s (standard aluminium section of DG-2496 of sizes 39.4 x 17.7 mm and 1.2 mm thick (min) including necessary jointing cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No), hinges type B-21, 100mm long (2Nos), suitable handle (1Nos) for each shutter complete all as specified and as directed.

S&F for 4 mm thick Sheet Glass, ordinary quality and glazing in square exc 0.50sqm in each pane fixed in aluminium windows complete all as specified and as directed.

S&F 200 mm long Aluminium anodised barrel tower bolts of extruded aluminium section complete all as specified and as directed.

S&F for 150 mm long Aluminium alloy handles cast type anodised complete all as specified and as directed.

S&F for 300 mm long aluminium alloy anodised sliding door bolts with hasp and staple (bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S&F for curtain rods (drapery rods) not less than 25 mm dia, anodised aluminium alloy with fixing brackets , rollers etc. fixed in repairs complete all as specified and as directed.

S&F for 20 mm outer dia 3 layer PP-R poly-propylene random copolymer concealed pipes SDR 7.4 (PN-16) UV stabilized and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc., including taking up or down steel tubing and connections complete all as specified and as directed.

S&F for 25 mm outer dia 3 layer PP-R poly-propylene random copolymer concealed pipes SDR 7.4 (PN-16) UV stabilized and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc., including taking up or down steel tubing and connections complete all as specified and as directed.

M&L for Preparing new or previously un treated surfaces of wood and wood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

M&L for preparing new or previously untreated surfaces of steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of exterior weather coat paint over a coat of primer of surfaces complete all as specified and as directed.

M&L for preparing surfaces plastered or unplastered old surfaces of walls and applying one coats of exterior weather coat paint complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and as directed.

M&L for preparing surfaces plastered or unplastered old ceiling surfaces and applying one coats of white wash complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and as directed.

M&L for preparation of old painted surfaces of walls and applying one coat of oil bound distemper complete all as specified and as directed.

Taking down and removing of existing water proofing treatment of any description completely, taking down of old cement plaster if any or roughening of surfaces and cleaning the top surface of RCC slab with using wire brushes and water to remove all dust and loose particles etc. complete all as specified and as directed.

M&L for rendering 15mm thick in cement mortar 1:3 on roof/ concrete surfaces with using water proofing compound as per manufacturer's instructions, surface finished even and smooth without using extra cement complete all as specified and as directed. (Supply only of water proofing compound/admixture shall be measured and paid separately).

Supply only of liquid waterproofing compound of approved make.

M&L for water proofing treatment with 4mm thick APP modified membrane weighing not less than 4Kg/Sqm reinforced with non woven polyester matt weighing not less than 160 Gram/Sqm having softening point not less than 140 degree celsius, longitudinal tensile strength not less than 300 N/Sqm, tearing strength of 180 N, laid after applying a coat of Bitumen Emulsion, Primer @ 0.20Kg/Sqm over the thoroughly cleaned surfaces to be water proofed. Membrane shall then be laid with 10Cm side overlaps and 15Cm end laps completely thermo fused by flame torch application as per manufacturer's instructions. Care shall be taken to avoid wrinkles while sticking the membrane on the bitumen surface. A coat of hot blown bitumen 90/15 shall be applied on top of the membrane @ 1.20 Kg/Sqm and finally finished with solar reflective aluminium paint @ 0.10 Kg/Sqm. The water proofing membrane shall be extended upto a height of minimum 30 cm on wall and inserted by cutting groove and filling with bitumen complete all as specified and as directed.

M&L for RCC 1:2:4 type B-1 (using 20mm graded stone aggregates) as slabs Supported on walls, beams and columns, Shelves and like complete all as specified and as directed.

M&L for form work to soffits of suspended slabs, landings and similar work, with rough finished surfaces of concrete complete all as specified and as directed.

M&L for Mild Steel TMT bars 8 mm dia cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with MS wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

Returning. Filling in, including spreading, leveling, watering and well ramming in layers n.exc 25cm complete all as specified and as directed.

Removing excavated materials n.exc 50m and deposing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed.

S&F for rotational moulded polyethylene water storage tanks IS : 12701 - 1996 marked (cylindrical vertical with threaded top) of 1000 Ltrs capacity hoisted and fixed in position all as specified in SSR Part-I complete all as specified and as directed.

S&F in repairs 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pire and fixed. (Minimum weight 455gms) complete all as specified and as directed.

M&L for Machine cut Cudappah stone slab 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade os slab complete all as specified and as directed.

M&L for Brickwork with sub-class `B' old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed.

Taking Down copper / aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling rose, pendants, regulators, sockets, light fittings, bulbs etc. removing materials to store for taking credit and making good disturbed surfaces of walls, floors, etc. complete all as specified and as directed.

M&L for point wiring complete with 1.5 Sqmm single core multistranded copper conductor, FRLS PVC insulated unsheathed cable 1100 volts grade fixed in and including Concealed PVC conduit, fitting and accessories, joints boxes including one 1.5 Sqmm copper FRLS PVC insulated unsheathed earth continuity conductor connected in the common earth, including suitable size metal flush box, modular cover plates, after wall cutting making good with Plaster and painting to match the existing surface including taking down the old wiring complete all as specified and as directed for following:-

One light/ Bell point controlled by one switch

One fan point controlled by one switch

One 3 pin socket outlet 5 amps on same board controlled by one switch

One 3 pin socket outlet 5 amps controlled by one switch on independent board.

One 3 pin socket outlet 15 amps / AC Metal Clad controlled by one switch on independent board with 4 Sqmm size cable

S&F of Modular Switch 5/6 Amps, 1 module 1 way complete all as specified and as directed.

S&F of Modular Switch 15/16 Amps, 1 module 1 way complete all as specified and as directed.

S&F Modular Socket 5/6 Amps, 2 Module 2 and 3 pin complete all as specified and as directed.

S&F Modular Socket 15/16 Amps, 2 Module 2/ 3 pin complete all as specified and as directed.

S&F Modular Fan Regulator Step type, 2 Module 1 Way, 120 Watt complete all as specified and as directed.

S&F 3 Modular Cover Plate with frame and metal flush box complete all as specified and as directed.

S&F 6 Modular Cover Plate with frame and metal flush box complete all as specified and as directed.

S&F Ceiling Rose, 3 plate/ PVC/ Polycarbonate, isolated body complete all as specified and as directed.

S&F 4 Feet LED Tube light of 20Watt Batten with integrated electronic driver having THD < 20%, burning hours not less than 50000 Hrs and aluminium housing with necessary fixing screws and connected upto ceiling rose with flexible multicore copper cable and making good complete all as specified and as directed.

S&F LED Bulb of 9 watt, 945 lmn, 6500 k color Temp, B22 base lamp complete all as specified and as directed.

S&F Lamp Holder, PVC/ Polycarbonate type with cord grip cap suitable for pendant fittings complete all as specified and as directed.

S&F 25 watt energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficient LED as lighting source and PC Cover having TOP opening separate driver compartment with IP66 protection and impact resistance of IK072 with necessary fixing screws and connected upto ceiling rose with flexible multicore copper cable and making good complete all as specified and as directed.

S&F in repairs SPN DB Double door, 230 V, 8 way with tray for provision of MCBs, Dolly for earth and neutral complete all as specified and as directed.

S&F in repairs Single pole and neutral enclosure with a two pin and earth plug and socket with one MCB SP 10 Amps complete all as specified and as directed.

S&F in repairs MCB DP 6-32 Amps, 10 kA, C Curve complete all as specified and as directed.

S&F in repairs MCB SP 6-32 Amps, 10 kA, C Curve complete all as specified and as directed.

M&L for sub main wiring with two run of FRLS single core cable PVC insulated unsheathed cable 1100 volts grade 4 Sqmm copper multistranded conductor including and drawing into concealed PVC conduit, fixed on wall, ceiling including one run of 4 Sqmm FRLS PVC insulated unsheathed multistranded for earth wire connected to earth, making good, complete all as specified and as directed. Note: Three run of 4 Sqmm cable and one run of PVC conduit shall be measured as one Rm.

M&L for Earthing complete with GI Earth Plate electrode 600x600x6mm buried directly in ground earth pit not less than 2.25 mtr below ground level with top edge of the plate not less than 1.5 mtr below ground level, surrounded from all sides with mixture of charcoal and common salt and electrode connected with GI earth lead wire of 4.0 mm by means of nuts/bolts/ check nuts/ washers , GI pipe light grade of 15 mm bore as protection pipe, GI wire of length not more than 7.5 mtr and connected to test point. GI pipe 20mm dia medium grade for watering, funnel with wire mesh, PCC pit and RCC (1:2:4) type B-1 for cover with 8 mm dia bar reinforcement both ways @ 140 c/c including excavation and earth work disposal of surplus soil to a distance not exceeding 50 mtr as shown on electrical plate No 3 of SSR 2009 complete all as specified and as directed.

S&F in replacement of 3-layer PP-R Polypropylene random copolymer pipes of 32 mm dia SDR 7.4 & SDR 11 UV stabilized and antimicrobial fusion welded having thermal stability for hot and cold water supply all PPR plain & brass threaded polypropylene random fixed to walls/ceiling including connecting it to the water tanks with necessary tank connectors, male and female threaded connectors, complete all as specified and as directed.

S&F in replacement of PP-R gate valve (brass insert) 32 mm as per requirement of the site complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth and getting out in soft/ loose soil for laying of water pipes / electric cable complete all as specified and as directed.

Returning, Filling in, including spreading, leveling, watering and well ramming in layers n.exc 25cm thick each, in soft/ loose soil complete all as specified and as directed.

M&L for cutting the existing DI pipe line connecting the PPR 32 MM Pipe line with necessary suitable size fittings/ ferrule/ clamps/ gaskets/ nuts & bolts/ reducers complete all as specified and as directed.

M&L for making connection of PPR distribution branch with PPR main of 32 mm dia size by providing and fixing tee/ reducer including cutting and making fusion joint etc. complete all as specified and as directed.

S&F monoblock pump set (Distribution) 1.0 HP 25x25 mm, 6m head, 640-4200 LPH, suitable for 230 V, 1 Phase system along with suitable capacity DOL Starter with PCC foundation complete all as specified and as directed.

Supply, laying and testing cable XLPE insulated, screened PVC bedded, galvansied steel strip or wire armoured, electric power cable (heavy duty) 1100 volts grade with stranded aluminium conductor of size 2 core 16 Sqmm complete all as specified and as directed.

M&L for dry sand filling in cable trenches for protection of cables with two layers below and above cable and punned down to specified thickness complete all as specified and as directed. Note: Punned down thickness shall only be measured for payment.

S&L Red clay bricks of class B Designation 75 for cable protection complete all as specified and as directed.

DHANA CONSTRUCTIONS

RMK INDUSTRIES