SPL REPAIR TO OR MD ACCN BLDG NO P 72 01 TO 08 OF KS LINES II AND CONSTR OF WAITING SHED ALONGWITH TOILET NEAR STOCKING WING AT OMC UNDER AGE BR II OF GE ARMY BHUJ

Amount

M&L for special treatment of sunken portion of WCs and Bath room as per following stages: Stage 1 :- Demolition of WC including lime concrete and cement concrete coba etc and preparing the surfaces of existing sunken portion of WCs or bath etc with wire brush to remove all loose dirt, oil grease etc . Stage 2:- Providing 10mm thick plaster in CM 1:3 with chemical of Dr. Fixit Pidicrete URP or plaster seal of STP Ltd Stage 3:- Applying Dr Fixit Primseal primer or STP Ltd (and allow to dry for 8 hours) under touch dry condition Stage 4:- Applying two coats of water proofing decorative elastomeric coating system of Dr Fixit Raincoats with DFT 100 Micron or shalicry 215 of STP(The surface after painting one coats shall be allowed to dry of 6 hours before next coats) all as per manufacturer instruction Stage 5:- Making holes in wall and fixing 600mm long 40mm dia GI spout for draining the surplus water if any.

M&L Plain cement concrete 1:4:8 type D-2 (using 40mm graded aggregate) as in mass filling in sunken portion complete all as specified and directed.

Taking down cement plaster of any description and in any position of brick or stone wall/concrete surfaces on walls ,ceiling etc including raking out joints ,hacking for key scrubbing down with water etc & prepared to receive new plaster complete all as specified and directed.

M&L for 15mm thick rendering on fair faces of brick/concrete surfaces in CM 1:4 finished even and smooth without using extra cement mixed with water proofing compound complete all as specified and directed. (Note :- WPC shall be measured & paid separately)

M&L for rendering 5 mm thick in Cement Mortar (1:3) on ceiling finished even and smooth without using extra cement complete all as specified and directed.

M&L for 10 mm thick rendering on surfaces other than fair faces of brick/concrete surfaces in CM (1:6) and finished even and smooth without using extra cement complete all as specified and directed.

Supply only Integral waterproofing compound complete all as specified and directed.

M & L for providing and applying putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and directed.

M&L for preparation of the newly plastered surfaces of walls & applying two coats distemper oil- emulsion, white or tinted over and including a coat of primer surfaces of wall complete all as specified and directed.

M & L for applying three coat of white wash on ceiling over new plaster surface complete all as specified and directed.

M & L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces with smart painting tools complete all as specified and directed.

M & L for providing and applying putty of 1 mm thickness over Old plastered surface to prepare the surface even and smooth complete all as specified and directed.

M&L for preparation of old surfaces by complete removal of existing treatment and applying two coats of oil bound distemper over and including one coat of primer on walls complete all as specified and directed.

M & L for applying one coat of white wash on ceiling over old decorated surface complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M & L for non skid ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed complete all as specified and directed.

All as per item No.16 above but on vertical surfaces including 10mm thick backing coat of tiles in CM (1:3) complete all as specified and directed.

S & F Non skid coloured plain/printed glazed tiles of size 300 x 300 x 6mm to 7 mm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 20 mm thick rendering in CM 1:4 complete all as specified and directed.

S & F coloured plain/printed glazed tiles of size 300 x 450 x 7 mm, on vertical surfaces such as skirting, dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 10 mm thick rendering in CM 1:4 complete all as specified and directed.

M & L for Granite slab work 18-20mm thick in floors steps, cooking platforms and like including pointing in white cement with admixture of pigment to match with granite shade over & including screed bed 15mm thick in CM 1:6 including cutting recess opening for the sink portion and embedding complete all as specified and directed (Note : No deduction shall be made for opening of sink portion, shall deemed to be included in the quoted rate)

M & L for Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and othersimilar situations complete all as specified and directed.

M & L for preparation of old steel painted surfaces exc 10cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frame) n exc 1.5 sqm each complete all as specified and directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frame) exc 1.5 sqm and n exc 4.0 Sqm each complete all as specified and directed.

Taking down shutters of any description and in any position exceeding 1 sqm & not exceeding 2 sqm each complete all as specified and directed.

S & F 35 mm thick factory made IInd class hard wood (not less than Hollock wood) glazed and skelton shutters open rebated and prepare to receive glass / gauze etc (without sash bars) edges of framing plain chamfered or rounded, fitted with moulded beads both sides for securing glass etc {size of members of shutters as specified in clause 8.24 (a) of section 8 of SSR - I} supplied and fitted to chowkat complete all as specified and directed.

S&F 2nd class hard wood factory made plain framed panelled door shutters 35mm thick (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both sides. The size of rail and stiles as per IS:1003 (Part I), Klin seasoned and chemically pressure treated.complete all as specified and directed.

S&F solid PVC door frame of size 50mmX47mm made out of 5mm both side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet reinforced with M.S. Square tube, suppling & fixing in opening all as per specifications and drawing shown on sl page No 150 of SSR part II (for item-884).complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & both side prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; panelling of both side prelam PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading & jointed together with solvent cement, supply & fixing in the frame at site as per SSR specifications & diagram/product drawing shown on sl page NO 146 of SSR Part II with the size of door shutter as required complete all as specified and directed.

S & F Powder coated Aluminium alloy sections sliding windows with frames Series-C (20mm) and , 3 track sliding shutters duly fitted with neoprene beading, glazing clips, shutters with tinted glass 5mm thick and stainless steel wire cloth 0.36mm dia and average width of aperture 1.4mm , aluminium alloy handles etc. complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire stapples complete all as specified and directed.

S&F butt hinges 100mm size medium weight cold rolled mild steel complete all as specified and directed.

S&F for butt hinges 100mm size medium weight stainless steel .complete all as specified and directed.

M & L for 150mm long extructed aluminium handle fabricated type complete all as specified and directed.

S & F Aluminium anodised barrel tower bolt of extruded section 200 mm size complete all as specified and directed.

S&F stainless steel sliding door bolt with hasp and stapple (bolt type) and fixing clips of sheet cast or extruded section with fixing bolts and sliding bolt of extruded section 300mm length & dia not less than 12mm with & including 6 Nos of bolts complete all as specified and directed.

Preparation of old painted surface of wood and wood based material any description and in any position over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L surface preparation of new wooden surfaces of any description, not otherwise described, over 10cm width or grith and apply two coat of synthetic enamel paint over and including one coat pink primer complete all as specified and directed.

S&F aluminium powder coated ventilator with fixed aluminium frame of size 65 x 40 x 1.98mm thick fixed in vertical position with aluminium vertical members and half portion to be provided with 4mm thick pin head glass and remaining portion to be louvered using 4mm thick pin head glass and louvered portion covered with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm incl necessary channel frame work, including rubber gasket and aluminium beading complete all as specified and directed.

S&F in repairs 20mm dia powder coated decorative type curtain rod incl brackets complete all as specified and diretced.

S&F in repair 10 litre capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets with flush pipe 32mm dia complete all as specified and directed. (Note: MAKE - CERA/PARRYWARE)

S & F in repair vitreous china wash basin, white flat back , size 450mmx300mm with and including Waste fittings, brass, chromium plated for basins with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed with and including Supplying and fixing cast copper alloy chromium plated, fancy type, pillar tap, 15mm bore, screwed down high pressure with or without lettered hot or cold with long shanks, screwed for iron pipe complete all as specified and directed. (Note: MAKE-CERA/PARRYWARE/JAQUAR)

S&F in repairs vitreous china water closet (squatting pan), orissa patern size 575 x 440 x 250 mm white with integral, foot rests an including 'P' trap and lime bedding making good to floors complete all as specified and directed. (Note: MAKE -CONFIRMING TO JAQUAR CAT PART-No. ECH-WHT-451LE)

S&F in repairs 15mm dia Bib taps cast copper alloy, with Chromiun plated crutch or butterfly handle screwed down,for iron pipe or brass ferule complete all as specified and directed. (Note: MAKE -CONFIRMING TO JAQUAR CAT PART-No. APR -101037)

S & F in repairs 15mm dia angle valves, Chromium plated crutch or butterfly handle screwed down high pressure, screwed both ends for iron pipes or for unions complete all as specified and directed.(Note: MAKE -CONFIRMING TO JAQUAR CAT PART-No. STE -107053)

S & F in repairs 15mm Concealed stop cock Reduced body with adjustable wall hange or butterfly handle screwed down high pressure, screwed both ends for iron pipes or for unions complete all as specified and directed.(Note: MAKE -CONFIRMING TO JAQUAR CAT PART-No. STE -107069)

S & F in repairs 15mm dia 2-in-1 bib tap with angle valves, Chromium plated crutch or butterfly handle screwed down high pressure, screwed both ends for iron pipes or for unions complete all as specified and directed.(Note: MAKE -CONFIRMING TO JAQUAR CAT PART-No. STE -107067)

S&F in repairs shower rose 100 mm dia of brass chromium plated fancy type with or without swivel joint suitable for fixing to 15mm bore GI pipe complete all as specified and directed.(Note: MAKE -CONFIRMING TO JAQUAR CAT PART-No. EOS-542N)

S&F in repair health faucet spray type jet with brass jet, chromium plated, and 1.0 m long PVC flexible pipe complete all as specified and directed .(Note: MAKE -CONFIRMING TO JAQUAR CAT PART-No. STE -107067)

S & F in repairs 15mm size PVC connections with PTMT nuts of length 450 mm.complete all as specified and directed.

M&L in repairs 40mm dia Low density poly ethylene pipes(LDPE) of pressure rating 6 Kgf/cm2 fixed complete to wall, ceiling or in floors etc complete all as specified and directed.

M&L for cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

S&F for Rotational moulded three layered polyethylene water storage tank(white) of 1000 liter capacity (cylindrical vertical with closed top incl float valve) hoisted and fixed in position all as specified and directed.

M&L for cutting grooves in brick wall, 75 mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 to ends of landings, steps, cills sunshades, shelves lintels etc complete all as specified and directed.

M&L for cutting holes or through PCC block / RCC wall built in CM and making good in CM 1:3 or cement concrete 1:2:4 type B-1 as required, superficial area exc 150 sqcm but n.exc 400 sqcm complete all as specified and directed.

Demolition and breaking up drain pipes (salt glazed ware, AC or Reinforced concrete) internal dia of pipe in 75mm set in cement mortar complete all as specified and directed.

Demolition and breaking up drain pipes (salt glazed ware, AC or Reinforced concrete) internal dia of pipe in 110mm set in cement mortar and taking out of trenches, if required complete all as specified and directed.

S&F 75mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 110mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes Type B ISI marked single socketed in any length with rubber ring joints laid on wall fixed complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes Type B ISI marked single socketed in any length with rubber ring joints laid on wall fixed complete all as specified and directed.

S&F 75mm dia PVC (SWR) branch piece single (single 'Y') equal or unequal with acess door complete all as specified and directed.

S&F 75mm dia PVC (SWR) branch piece Double (single 'Y') equal or unequal with acess door complete all as specified and directed.

S&F 110mm dia PVC (SWR) branch piece Tee (Single 'T') equal or unequal with acess door complete all as specified and directed.

S&F 75mm dia PVC (SWR) bends any radius with access door complete all as specified and directed.

S&F 110mm dia PVC (SWR) bends any radius with access door complete all as specified and directed.

S&F for PVC (SWR) floor trap long body type, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

S&F for PVC (SWR) vent cowl 110 mm bore complete all as specified and directed.

M&L for PCC 1:2:4 type B1 (using 12.5 mm graded aggregate) as in hold fast, cill etc with necessarry form work complete all as specified and directed.

Taking up or down existing unserviceable upvc/ mild steel water tubing and connections 15mm dia, any grade, of any description or in any position including fittings complete all as specified and directed.

Taking up or down existing unserviceable upvc/ mild steel water tubing and connections 20mm dia, any grade, of any description or in any position including fittings complete all as specified and directed.

Supplying and laying 20 mm outer dia Unplasticised PVC SDR 13.5 and plain CPVC SDR 11 fittings pipes fixed complete to walls, ceilings or in floors etc., any type of pipe etc in required length complete all as specified and directed.

Supplying and laying 25 mm outer dia Unplasticised PVC SDR 13.5 and plain CPVC SDR 11 fittings pipes fixed complete to walls, ceilings or in floors etc., any type of pipe etc in required length complete all as specified and directed .

M & L for brushing neat cement slurry with 3 Kg/Sqm of cement incl complete removal of existing roof treatment complete all as specified and directed.

M & L for 25mm thick PCC of type B-1, 1:2:4 (using 20mm graded stone aggregate) for padding complete all as specified and directed.

M & L Rendering 10 mm thick of CM 1:4 on concrete roof surfaces is to be finished even and smooth without using extra cement with mixing water proofing compound @3% by weight complete all as specified and directed.

M & L in repairs App based polymeric membrane minimum weight 3.5 Kg/Sqm and Minimum 3 mm thick reinforced with polyester non wove fabric (Wt. not less than 150 gms/Sqm land on primed surface by torched application completed all as specified and directed.

M & L for cleaning surface and applying two coats of aluminium paint on roof or vertical surfaces complete all as specified and directed.

M & L for machine cut kota stone slab size as in flooring, stair case landing. treads of steps, 18-22mm thick over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including 20mm thick screed bed or bedding in cement mortar 1:6 complete all as specified and directed.

M & L for machine cut kota stone slab size as in skirting, dado, vertical surfaces etc, 20-25mm thick over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including backing coat 15mm thick cement mortar 1:3 complete all as specified and directed.

S&F sinks without drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes ; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting unions to pipe, overall size 495mmX420mm bowl size 410mmX330mmX160mm complete all as specified and directed.

S&F in repair of PVC cabinet size 650 x 400mm, comprising of looking glass, space for bath soap, shampoo, tooth brush and paste, handle towel rail complete all as specified and directed. (Makes :- HINDWARE / CERA / NEYCER / PARRYWARE/CLASSIC)

M & L for 75 mm thick PCC 1:3:6 type D-2 (using 40mm graded stone aggregate) as in as in sub base complete all as specified and directed.

M & L for providing precast cement concrete Type B1 1:2:4 (using 20 mm graded aggregate) in appex stone/kerb stone with plain fair faces including chamfers, weathering throting etc and set in cement mortar 1:4 complete with joints to math size and shape complete all as specified and directed.

M & L for sand filling 50 mm thick under floor/over floor or in foundations including well ramming complete all as specified and directed.

M & L for 60 mm thick coloured interlocking PCC tiles in approved design/colour set laid over compacted sub soil / sand complete all as specified and directed.

M&L for exterior grade, coloured, cement concrete designer chequered tiles of size 30cm x 30cm x 25mm thick set, jointed and pointed in neat cement slurry with grey cement and pigment to match the shade / colour / matrix of tiles as in floor etc. complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise spefifically provided complete all as specified and directed.

M&L for removal of existing loose damage concretye, dust, oil, paint, grease, etc from structural member like roof slab, beam, column, chajja, etc exposed fully if any corroded steel in the repair area and remove all the scale and corrosion deposite and applying Dr fixit rust removal and Epoxy Zinc Primer over the cleaned steel bars if and pour the mixed Dr fixit micro concrete into a watertight shuttering after primed by one coat of Dr fixit Epoxy bonding. Thickness or depth of an area n. exc 10cm and all as per manufature instruction complete all as specified and directed. (Note - The rate included S&F of addition reinforcement bars if any required.)

S&F Window Canopy which is made with a durable polycarbonate /Glass / fiber /acrylic sheet and steel brackets for roof covering / cladding to wall, fixed with hold fast complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10 cm width / girth & applying 2 coat of synthetic enamel paint over acoat of red oxide complete all as specified and directed.

Providing & applying Rising damp-proof coating system with Single component ready to use damp-proof coating Roff Hydamp : 1.SURFACE PREPARATION: Thoroughly brush and clean all laitance, loose particles such as dirt, grease, mortar droppings, release agents, efflorescence, bird droppings, etc. All large voids or hollow portions must be removed and re-plastered. Non- moving cracks having width upto 5 mm must be filled with Polymer based crack filler. 2 APPLICATION: Apply the first coat of Dr Fixit Dampguard Classic with a paintbrush directly on the prepared surfaces by mixing ( 1 part base:1 part hardner: 1 part of water) . Allow to dry for a minimum 2-3 hrs. Apply one part of DAMPGUARD mixed chemical and 2 parts of OPC white cement/Birla Putty and make the Putty, apply Putty on the entire surface area. Allow it to dry for at least 3-4 hours. Apply the Final coat of Dr Fixit Dampguard Classic on the entire surface and allow the surface to air cure 48 Hrs proceeds to paint.

M & L for mild steel bars conforming to Fe 290 Gde E-165 as in guard bars or similar works including welding etc complete all as specified.

Demolition of concrete block masonry built in cement mortar or cement lime mortar complete all as specified and directed.

M&L for Pre-cast cement concrete block masonry (Type C1, 1:3:6, 20mm aggregate) with solid blocks, exc. 10cm in width and setting in cement mortar (1:6), complete all as specified and directed.

S&F SS 1st grade Kitchen Plate rack over all size (36x48x10 in inches) conforming to Jainko Cat part No. KRJ-9 or equivalent complete all as specified and directed.

S&F 18 mm thick prelaminated PVC Cheluka ply prelaminated one side with decorative choice lamination and other side plain fixed with screws to PVC celuka ply works all as directed and as per manufacture instructions complete all as specified and directed. Make : Rajshree plasticwood

All as per Above item No 99 but 18 mm thick plain cheluka plywood complete all as specified and directed.

All as per Above item No 99 but 12 mm thick plain cheluka plywood complete all as specified and directed.

All as per Above item No 99 but 05 mm thick plain cheluka plywood complete all as specified and directed.

S&F in repair Kitchen basket stainless steel for Cup and saucer basket size 430 x508x100 mm made oue of not less than 3 mm dia stainless steel rod of grade 304 along with 01 set of telescopic channel (heavy duty )of size 300mm/450mm long, roller of size 45 mm x25mm x20 mm and magnetic and connected plates to shutters complete all as specified and directed.

S&F in repair Kitchen basket stainless steel for Partition basket size 430 x508x100 mm made oue of not less than 3 mm dia stainless steel rod of grade 304 along with 01 set of telescopic channel (heavy duty )of size 300mm/450mm long, roller of size 45 mm x25mm x20 mm and magnetic and connected plates to shutters complete all as specified and directed.

S&F in repair Kitchen basket stainless steel for Plain basket size 430 x508x100 mm made oue of not less than 3 mm dia stainless steel rod of grade 304 along with 01 set of telescopic channel (heavy duty ) of size 300mm/450mm long, roller of size 45 mm x25mm x20 mm and magnetic and connected plates to shutters complete all as specified and directed.

S&F in repair Kitchen basket stainless steel for Dish(plate) basket size 430 x508x250 mm made oue of not less than 3 mm dia stainless steel rod of grade 304 along with 01 set of telescopic channel (heavy duty )of size 300mm/450mm long, roller of size 45 mm x25mm x20 mm and magnetic and connected plates to shutters complete all as specified and directed.

S&F brass Handle fabricated type polished of Size 100 mm complete all as specified and directed.

S&F brass Handle fabricated type polished of Size 75 mm complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundations etc. or for shafts, well cess its, manholes, pier holes, etc. but not exceeding 10 Sqm on plan and getting out in hard/dense soil complete all as specified and directed.

M & L for Surface excavation in soft/loose soil n exc 30 cm deep and averaging 15 cm deep and getting out complete all as specified and directed.

M & L for Returning, filling in including spreading, levelling, watering and well ramming excavated soil in layers n exc 25 cm thick back in trenches complete all as specified and directed.

M & L for removing excavated material exc. 250 m but n exc. 500 m and depositing complete all as specified and directed.

M & L for Non skid Coloured ceramic tiles 300mm X 300mm X 7mm thick in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over & including screed 15mm thick in CM 1:4 complete all as specified and directed.

M & L for precast concrete block masonary with PCC solid blocks in (1:3:6), type C1 (using 20mm graded stone aggregate) exceeding 10cm in width andsetting in Cm (1:4) complete all as specified and directed.

M&L for 15 mm rendering in two layers with 10 mm with CM 1:6 & 5 mm thick with CM (1:4) with using water proffing compound on fair face of wall or on concrete surfaces finished even and smooth without using extra cement complete all as specified and directed. (Note: WPC paid seprately.)

M & L for rendering 10mm thick in cement mortar 1:6 on Block/Brick masonry surfaces of internal wall finished even and smooth complete all as specified and directed.

M & L for rendering 5mm thick in cement mortar 1:3 on fair faces of concrete surfaces as in ceiling complete all as specified and directed.

Preparation of newly plastered surfaces of external wall and applying two coat of cement base paint over one coat of cement primer in camouflage pattern etc complete all as specified and directed.

M & L for preparation of newly plastered surfaces of wall and applying three coat white wash complete all as specified and directed.

M & L for preparation of newly plastered surfaces on ceiling and applying three coat white wash complete all as specified and directed.

M & L for RCC type M-25 Nominal mix (using 20mm graded aggregates) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M & L for RCC type M-25 Nominal mix (using 20mm graded aggregates) as in lintel over 1.5 m span, complete all as specified and as directed.

M & L for RCC type M-25 Nominal mix (using 20mm graded aggregates) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M & L for RCC type M-25 Nominal mix (using 20mm graded aggregates) as in column, complete all as specified and as directed.

M & L for TMT steel bar Gde 500 D, 6 mm to 8 mm dia as in reinforcement cut to length, bent to shape required including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M & L for TMT steel bar Gde 500 D, 5 mm dia and over upto including 10 mm dia as in stirupps, spacers and binders reinforcement cut to length, bent to shape required including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M & L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M & L for Formwork for rough finished surface of concrete and sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work complete all as specified and directed.

M & L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping) complete all as specified and directed

M & L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed

M&L for PCC (1:4:8) type D-2, (using 40 mm graded stone aggregate),100 mm thick, as in sub base for floor, finished even and rough complete all as specified and directed.

S&F figured glass 3 mm thick pin headed type and glazing withoil putty not exc0.5 mm in each pane complete all as specified and directed.

S & F MS for Framed / Door ,ladders with gusset plates rails, braces etc. complete drilled for fixing of other coverings doors etc to be prepared for sliding with and including either hooks and hinges, etc completed as specified size of frame conforming to Fe 410-W(Gde E-250) quality -A and filled with PCC 1:3:6 type C-0 making good to disturbed surface complete all as specified and directed.

S&F 150 mm long aluminium anodised , barrel tower bolt of extruded section and fixed complete all as specified and directed.

S&F aluminum handles cast type, anodized of 150 mm size complete all as specified and directed.

S & F stainless steel butt Hinges, medium weight, , 100 mm size complete all as specified and directed.

S&F Stop valves, ISI marked , cast copper alloy, screwed down high pressure for 15 mm bore dia tubing pipe, high pressure, with crutch butter fly handle complete all as specified and directed.

S&F UPVC ball valve with operating handle (stop valve) of size 1" (25mm dia) both ends threaded complete suitable for fitting with ASTMD-1785, Sch 40 UPVC pipes complete all as specified and directed. (Make : Prince/Finolex/Supreme/Kisan)

Supply & fix in any length UPVC pipe manufactureed as per ASTM-D -1785 both ends threaded as per IS-559, Schedule -40 complete with fitting,fixed to wall/ceiling/floors in required length complete all as specified and directed of the following inner bore 15mm.( Make : FINOLEX/ SUPREME/ KISAN/ PRINCE)

Supply & fix in any length UPVC pipe manufactureed as per ASTM-D -1785 both ends threaded as per IS-559, Schedule -40 complete with fitting,fixed to wall/ceiling/floors in required length complete all as specified and directed of the following inner bore 25mm. (Make : FINOLEX/ SUPREME/ KISAN/ PRINCE)

S&F Bib taps, cast copper alloy screwed down high pressure with crutch or butter fly handle fancy type long body CP for 15mm dia bore GI Pipe or for brass ferrule and fixed complete all as specified and directed.

S&F Vitreous China urinals, bowl type urinal flat back, size of 465 x 355 x 265 mm long white with grating and union for discharge pipe ,complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe etc, complete all as specified and as directed.

S&F vitreous china wash basin white flat back size 580x450mm (counter top) including bracket, including down pipe ,PVC connection pipe 15mm bore, and 32mm CP waste coupling incl pillar tap complete all as spcified and as directed.

S&F Rotational moulded poly-ethylene multilayer water storage tanks (cylinderical vertical with closed top) 500 litres capacity, hoisted and fixed in position complete all as specified and directed.

M&L for concrete bed to drain pipes in cement concrete (1:4:8) type D2 (using 40mm graded stone aggregate) including packing under, and hauching against the side of the pipes after they are laid tested for pipes of 150mm dia complete all as specified and directed.

S&F jointing and testing for reinforced concrete drain pipes, 150mm bore, class NP-2, laid and jointed with collar in CM (1:1) complete all as specified and directed.

M & L for water proofing treatment to roof by applying one coat of bituminous / polymrised primer confirming to IS 3384 @ 0.30 ltr /sqm and laying Actetic Polypropylene (APP) modified membrane pre-fabricated , reinforced with non woven polyester , of 3.50 kg/sqm (minimum) , 3mm thick minimum with minimum 75mm side overlaps and minimum 100mm end overlaps and applying bituminous aluminium paint over APP membrane @ 100 gram/sqm on roof or vertical surfaces complete all as specified and directed.

S & F of Steel work in tubular trusses/purlin including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed.

M&L for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for Cement concrete type B-1,1:2:4 (20mm graded aggregate)75 mm thick complete all as specified and directed.

M&L for fixing Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in soft/loose soil complete all as specified and directed.

M & L for Cement concrete in foundations, filling and mass concrete using type B2 1:2:4 (40 mm gradaed aggregate) complete all as specified and directed.

S & F of Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for PCC (1:3:6) type C2, (using 40mm graded stone aggregate) as in plinth protection, 75 mm thick, finishing the surface even and smooth w/o using extra cement including forming & filling expension joints 65 mm deep x 10 mm wide filled with sealing compound grade A complete all as specified and directed.

Dismantaling and taking down copper / aluminium point wiring any type / size complete with removing all connection and accessories such as switches , sockets, ceiling rose,pendent holder,fan regulator any type , all type of fitting , batten , steel or PVC conduit , casing caping etc compele and making good the disturbed surface complete all as specified and directed.

Taking down old and unserviceable sub main wiring any size / type / core incl earth wire complete with batten/conduit etc and making good the disturbed surface to match the existing disturbed surface all as directed.

Taking down old and unsrevicable sheet metal enclosure, switch fuse unit, distribution bord any type /way / capacity including fuses,MCB's, insulator etc complete after removing all connection and making good the disturbed surface complete all as specified and directed.

M&L for point wiring with using 1.5 Sqmm (nominal area) multi standard copper conductor, single core, FRLS PVC insulated & unsheathed cable, 1100 volts grade with and including PVC conduit pipe of adequate size concealed in stone masonary wall type , fixed to surface on ceiling with PVC rawl plugs with sunken type pressed steel terminal box and junction boxes 1.6mm thick of suitable size and wiring to be terminated in pressed steel sunken boxes with and including all accessories and using 1.5 Sqmm (nominal area) stranded copper conductor single core conductor, FRLS PVC insulated & unsheathed cable as in earth wire connected to common earth dolly complete all as specified and directed for following:- NOTE :- (i) Quoted rate shall be deemed to include the cost of cutting chases in walls / pillars /column etc. of any description for concealing the boxes to required depth & making good the disturbed surface in CM 1:4 including finishing the surface to match with the existing surface. (ii) Fittings like modular switches, sockets, regulators, lamp holders, light fittings shall be measured and paid for separately under appropriate item of Schedule `A'. (iii) The quoted rates shall be deemed to be inclusive for provision of covering modular sunken boards/terminal boxes / junction boxes of any shape and size with modular type white plate and frame with suitable brass screws and cup washers

(a) One light point controlled by one way one switch SP 5 Amps ,240 V complete all as specified and directed.

(b) One light point controlled by two 2 way switch SP 5 Amps ,240 V complete all as specified and directed.

(c) One ceiling/exhaust fan point controlled by one way one switch SP 5 Amps, 240 V complete all as specified and directed.

(d) One switch socket outlet 3 Pin, 5 Amps, SP on independent board complete all as specified and directed.

(e) One switch socket outlet 3 Pin, 5 Amps, SP on same board complete all as specified and directed.

(f) One bell / buzer point controlled by one push button switches on independent board complete all as specified and directed.

All as per the above item No 159 herein before but with 2.5 Sqmm cable for 3 Pin 5/15 Amps switch socket outlet complete all as specified and directed.

(d) All as per above Item no 159 here in before but of using FRLS cable of size 4 sqmm for phase and neutral and by using 2.5 sqmm FRLS cable for earth continuity complete all as specified and directed.

S&F modular switch one way 6 Amps , 1 module type complete all as specified and directed.

S&F modular switch two way 6 Amps , 1 module type complete all as specified and directed.

S& f modular socket , 6 Amps , 2/3 pin combined 2 module complete all as specified and directed.

S& f modular switch socket combination,6 Amps / 16 Amps , 2/3 pin combined 2 module complete all as specified and directed.

S&F ceiling rose surface backlite 65 x 20mm size three terminal ISI marked complete all as specified and directed.

S&F Bell push 6 Amps 1 module complete all as specified and directed.

S&F bell Multi music type 240 Volt , Single Pole ISI marked complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20 W, 220V,AC decorative box type with driver, holder including LED tube light connecting upto PVC insulated 3 core flexible cable from ceiling rose to fitting drawn through in PVC flexible conduit including as per site requirement and 2 Nos of round or square PVC bolck for fixing of FTL fitting complete all as specified and directed.

Supply and fixing of mirror light of capacity 1x10 Watt epoxy white powder coated CRCA sheet steel housing with acrylic diffuser gaskat with all fixing acessories complete all as specified and directed.

Supply & fixing modular fan regulator step type , 2 module complete all as specified and directed.

M&L for sub main wiring with two runs of 6 Sqmm (2x6 sqmm )1100 volts grade single core FR PVC insulated unsheathed multistranded copper conductorcable confirming to IS-694 drawn through and including non-metalic PVC rigid conduit 25 mm dia ISI marked with all conduit accessories concealed in walls/roofs/floors etc with one run of 4 Sqmm (1x4 sqmm ) single core FR PVC insulated unsheathed copper conductor cable as earth wire complete all as specified and directed. Note:- 2 runs of 6 Sqmm ,one run of 4 Sqmm ( 2x6 sqmm + 1x4 sqmm ) cable and one meter of conduit will be measured as one unit again.

S&F sheet metal enclosures for distribution board when MCB to be used SPN ( Single pole and neutral ) 8 way, 240 Volts, sheet metal powder coated, IP 42 protection with 200 Amps rated bus bar, double door type complete all as specified and directed.

S&F sheet metal enclosures for distribution board with MCCB when MCB to be used TPN ( Triplepole and neutral ) 4 way, 415Volts, sheet metal powder coated, IP 42 protection with 200 Amps rated bus bar, double door type complete all as specified and directed.

S&F MCCB of capacity 100 Amps , 415 Volts, rupturing capacity 16 KA complete all as specified and directed.

S&F MCB SPN, 63 Amps, 240 Volts, rupturing capacity 10 KA."C" Series complete all as specified and directed.

S&F MCB SPN,40 Amps, 240 Volts, rupturing capacity 10 KA."C" Series complete all as specified and directed.

S&F MCB SP, 5 to 32 Amps, 240 Volts, rupturing capacity 10 KA "C" Series complete all as specified and directed.

M & L for earthing complete for machinary / Equipment installed at power house / sub station with galavanised steel earth plate electrode of size 60 cmx 60 cmx 6 mm thick buried directly in ground ( earth pit not less then 2.25 m deep below the normal ground level ) with top edge of the earth plate not less then 1.5m below normal Ground level connected galvanised earth lead wire 4.0mm dia by means of bolts, nuts, washerws and check nuts all shown in electrical plate No.5 of SSR Part- I connected to main board / disribution board complete .Earthing GI lead and GI protection pipe 15 mm dia light grade upto 7.5 m from earth pit connecting to machinary/ equipment, testing point, all as specified and testing on completion all as specified and directed. Note :- (i) The unit rate shall also included for earth work in hard /dense soil , PCC type C-I (1:3:6) chamber , PCC 1:2:4 type B-I cover 50 mm thick reinforced with 8 mm dia TMT bars,150 mm c/c both ways, funnel with watering pipe 20 mm dia medium graded , GI protection pipe light grade 15 mm dia and wire mesh complete in addition to items No. 1(a) to (e) of preamble (notes) under sub heading earthing specified on SI page No. 389 of SSR Part - II. (ii) Earthing lead and GI protection pipe beyond 7.5 mtrs will be measured and paid separatelly if required under appropriate Schedule. Note for Testing :- (i) Earthing shall be tested as specified in casul 19.137 of SSP PART - I 2009 , to the entire satisfication of Engr-in-Charge. (ii) On teting after complataion of earthing, if the desired earth resistance is not obatined the earthing wiil be re done by the contractor at his own risk and cost to the entire satisfaction of the Engr - in - charge.

S & F angle holder backlite with 1x11 Watt CFL with fixed on hylum sheet including all fixing acessories and making of connection with twin core flexible copper conductor from ceiling rose to fitting complete all as specified and directed.

Taking down celing fan /exhaust fan/geyser and refixing of the same including all necessary fixing arrangment & civil work after completion of work as specified and directed.

Repair of celing fan /exhaust fan, painting, overhauling, greasing and replacement of U/S componante like capacitor to make functional including provision of 3 core flexible copper conductor from ceiling rose to fan complete all as specified and directed.

Taking down electric meter and refixing after complation of work and connecting from DB etc complete all as specified and directed.

Supply and Fix modular switch 16 Amp, one way, 1 module, 230 volts AC circuit complete all as specified and directed.

Supply and Fix socket modular 6 /16 Amp, 2/3 pin combined, 2 module, 230 volts AC circuit complete all as specified and directed.

S & F sheet metal enclosure powder painted for MCB DB SPN 04 way double door with IP-42 protection with Din rail and busbar complete all as specified and directed.

Supply & Fix in repair MCB SPN 415V, C series, 6 to 32 .Amps 10 KA rating ISI marked and connecting complete all as specified and directed.

S & F in replacement elegantly industrial general purpose box type luminaire, 1x20 Watt, designed box type LED luminaries, CRCA sheet steel housing with white reflector cover fitted to the body with decorative end covers complete with electronic ballast, spring loaded rotor type lamp holders, connected block with and including 01 No LED lamp 20 Watt and all accessories, pre-wired and connecting the same to ceiling rose with & including twin core PVC insulated and sheathed copper conductor 23/0.0076 cable including all accessories and fixing arrangement for fixing the light fitting to walls / roof surface over and including 2 Nos PVC square box complete all as specified and directed.

S & F Exhaust fan ventilator DX 250mm sweep 36W ideal for mounting on glass/wooden window 220/230 Volts AC steel body and connecting up to the ceiling rose with flexible three core copper conductor of size 23/.0076 including provision to fix the ventiliar fan to the glass/wooden window/ by providing duitable fixing arrangement, farse nut, bolts etc complete all as specified and directed.

Supply and fix ceiling fans, complete with three blades, down rod, accessories 230V, 1200mm sweep, min air delivery 210 CFM with BEE star rating, with Squirrel cage induction motor with connection from ceiling fan to ceiling rose with PVC insulated FRLS 3 core 0.75 sqmm copper flexible conductor complete all as specified and directed.

Supply and fix XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade of the following cross sectional area 10 sqmm 2 core complete all as specified and directed.

Supply and fill dry river sand in trenches for cable cushioning over and below the cable complete all as specified and directed. ( The punned thickness shall only bev measured)

Supply and fix precast concrete cable covers class LV type 1, flat size 250 x 150 x 40 mm M-20 grade concrete laid dry for cable protection complete all as specified and directed.

Supply and fixing in any length UPVC pipesize of 40 mm dia manufacture as per ASTM-D-1785 as per IS-559, Sch-40 complete with fittings, laid in treanches in required length complete all as specified and directed.

M & L for cutting the existing GI / PVC pipe 100 mm / 50 mm dia in position for insertion of new Tee for branch connection complete all as specified and directed.

S & F UPVC ball valve with operating handle (stop valve) of size (25 mm dia) both ends threaded complete suitable for fitting with ASTMD-1785, Sch 40 UPVC pipes all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundations / taking out / in cables / pipes etc. or for shafts, well cess pits, manholes, pier holes,road cuttings etc. but not exceeding 10 Sqm on plan and getting out in any type of soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layer not exceeding 25 cm thick in soil complete all as specified and directed.

Removing surplus soil obtained from excavation to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting paint complete all as specified and directed.

NOTE APPLICABLE FOR ALL ITEMS :- If rate quoted for similar/identical items in same part of Sch ‘A’ is at variance, the lowest rate quoted shall only be considered for payment to the contractor.

M/s Bombay Novelty Stores (BID ID -3147569)