801510/E8 IMPROVEMENT TO SMQS AT AF STATION SURYALANKA

Amount

Demolition of Brick or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars etc., but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position including reinforcement cut as required to facilitate demolition complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), and aprons removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Taking down chowkats or frames (without taking off shutters from the frame) not exceeding 1.5 sqm each and removing to store complete all as specified and directed.

Taking down chowkats or frames (without taking off shutters from the frame) exceeding 1.5 sqm but not exceeding 4 Sqm each and removing to store complete all as specified and directed.

Dismantling unframed timber scantling under 40sqcm in section, in any position as in rafters, purlins etc as in window sun shades etc ,complete all as specified and directed.

Dismantling Asbestos cement (corrugated, semicorrugated, etc) sheets in roof covering in window sunshades etc, complete all as specified and directed.

M&L for rendering 5mm thick on fair faces of concrete surfaces in cement mortar 1:3 in ceiling surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10mm thick on fair faces of brick or concrete surfaces in cement mortar 1:6 finishing even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in two layers, first layer 10 mm thick in CM 1:6 and second layer 5 mm thick in CM 1:4 finishing fair and even mixed with WPC as per manufacturer's instructions complete all as specified and directed. Note : Supply of water proofing compound shall be measured and paid seperately.

Supply only integral water proofing compound of approved make complete all as specified and directed.

M&L for Brickwork with sub-class `B' old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

M&L for precast reinforced cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in cover slabs,(Manholes etc) chullah hoods, etc and similar articles with plain faces including necessary formwork set in cement mortar 1:6 complete all as specified and directed. Note :- Reinforcement shall be measured and paid separately under relevant item.

M&L for RCC 1:2:4 type B-1 using 20mm graded stone aggregates as in chajjas complete all as specified and directed.

Use and waste of form work to chullah hoods, chajjas, troughs and similar items including edges with rough finished surfaces of concrete complete all as specifiedand directed.

M&L for Mild Steel TMT bars 8 mm dia cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with MS wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for 75mm thick plain cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggregates as in foundation and sides of Gully trap portion complete all as specified and directed.

M&L for 25 mm thick cement concrete 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in flooring below floor tiles etc. complete all as specified and directed.

M&L for Non Skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for joint free non Skid ceramic coloured tiles (matt finish) 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for 100 mm high skirting with joint free non Skid ceramic coloured tiles (matt finish) 7 to 8 mm thick high area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tile, laid over and including 10 mm thick backing coat in cement mortar 1:4 complete all as specified and directed.

M&L for Glazed ceramic coloured tiles 300 x 200mm size 7 mm thick in vertical surfaces as in dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 10mm thick backing coat in cement mortar 1:4 complete all as specified and directed.

M&L for 18-20 mm thick Polished Granite stone slabs of any type machine cut bedded and jointed with grey cement slurry and pointed with white cement with admiture of pigment to match the shade of granite stone including grinding and polishing laid over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for 18-20 mm thick Polished Granite stone slabs of any type machine cut fixed as in shelves with cement slurry complete all as specified and directed.

M&L for 20-25 mm thick Kota stone slabs in floorings laid and jointed with grey cement slurry mixed with pigment to match the shade of the salb including rubbing and polishing and laid over and including 20 mm thick cement screed bed in cement mortar 1:6, complete all as specified and directed.

M&L for 20-25 mm thick Kota stone slab as in risers of steps, skirting, dado and pillar laid over and including 10 mm thick backing coat in cement mortar 1:4, and jointed grey cement slurry mixed with pigment to match the shade of the salb including rubbing and polishing complete all as specified and directed.

M&L for rounding to the edges of stone slabs on edge as in steps, cooking platform, and other similar situations complete all as specified and directed.

M&L for Chequered cement concrete tiles 30 cm x 30 cm x 25 mm thick with grey cement and pigments, set, jointed and pointed in neat cement slurry in floors/ pavings etc laid over and including 20 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for 75 mm thick plain cement concrete 1:3:6, type C-1, using 20mm graded stone aggregate as in plinth protection, paving etc. surface finished even and smooth without using extra cement complete all as specified and directed.

S&F Pressed steel frames 125 x 60mm size for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

S&F Pressed steel frames 105 x 60mm size for doors with one or more rebate including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

S&F Pressed steel frames 75 x 50 mm size for cup boards with one rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

M&L for Plain cement concrete 1:3:6 type C-0 using 12.5mm graded stone aggregate for filling of hollow portions of door frames etc., complete all as specified and directed.

S&F 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 35 mm thick second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass,gauze etc.( with out sash bars), edges of framing plain, chamferedwith plain chamfered or rounded, mitred and rebated , edges of framing plain, chamferred or rounded, fitted with cut and mitred beads for securing glass, wire gauge etc. ; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) fitted to chowkats complete all as specified and directed.

S&F in repair 18/19mm thick Block board, Grade 2 quality, interior Grade, commercial type, with decorative face veneer on both faces, fixed with screws etc as in shelves of cup boards etc., complete all as specified and directed.

M&L anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleats,aluminium grills for fixing etc., complete all as specified and directed .

S&F Anodised aluminium window and ventilator glazed /Gauged shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1No) each shutter, hinges type B-21 100mm long (2Nos), suitable handle (1No), complete all as specified and directed.

S & F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or wooden/aluminium beeds complete all as specified and directed.

S&F 4 mm thick Sheet Glass, ordinary quality and glazing in square exc 0.50sqm in each pane fixed in aluminium windows complete all as specified and directed.

S&F 4 mm thick Figured glass, pin head type and glazing in square n.exc 0.50sqm in each pane fixed in aluminium ventilators complete all as specified and directed.

S&F 200 mm long Aluminium anodised barrel tower bolts of extruded aluminium section complete all as specified and directed.

S&F 150 mm long Aluminium anodised barrel tower bolts of extruded aluminium section complete all as specified and directed.

S&F 100 mm long Aluminium anodised barrel tower bolts of extruded aluminium section complete all as specified and directed.

S&F 150 mm long Aluminium alloy handles cast type anodised complete all as specified and directed.

S&F 100 mm long Aluminium alloy handles cast type anodised complete all as specified and directed.

S&F 75 mm long Aluminium butt hinges extruded aluminium alloy with galvanised steel wire pin anodised, type C-22 complete all as specified and directed.

S&F in repairs 75 mm size Hasp and Staple aluminium anodised safety type with pin hinge including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F 300 mm long aluminium alloy anodised sliding door bolts with hasp and staple (bolt type) and fixing clip of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F Mild steel 300 mm ,ordinary rat & tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F in repairs curtain rods (drapery rods) not less than 25 mm dia, anodised aluminium alloy with fixing brackets , rollers etc complete all as specified and directed.

S&F for factory made PVC Solid Door frame of size 50mmx47mm made out of 5mm plain coloured PVC sheet reinforced with MS Square tube, supplying & fixing in opening as per specification and dawings all as specified and directed

S&F Factory made Solid panel PVC Door Shutter of 30mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colourr PVC 'C' channel having a PVC sheet strip 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; Panelling of plain clour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beeding and jointed together with solvent cement as per specification and drawing complete all as specified and directed.

S&F joist, channel, angle of tee sections fied independently, without connecting plates etc rietting etc conforming to (Fe-410-W) Gde-E-250) quality "A" complete all as specified and directed.

Supply and fix pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with L type or J type or cranked hook bolts along with bituminous washers in lieu of screws etc complete all as specified and directed and as per manufacturer's instructions.

S&F in repairs vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap, and to flushing pipe, anti-syphonage pipe, etc., fixed in repairs complete including making good to floor complete all as specified and directed by Engineer-in-Charge.

S&F in repairs10 lit capacity PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed by Engineer-in-Charge.

S&F in repairs Vitreous China wash basin, white, flat back, of size 550x400 mm including brackets, cutting for and pinning in ends of brackets or errecting stand and but exclusive tap, waste fitting and waste pipe etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs CP Pillar taps fancy type 15 mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe, complete all as specified and directed.

S&F in repairs of 20 mm bore Gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repairs of Stop valves 15 mm bore, fancy type Chromium plated cast copper alloy screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions, all as specified and directed.

All as per serial item No. 65 above but fancy type, chromium plated with long shank and cup (Concealed type).

S&F in repairs 15 mm bore Bib taps, chromium plated, cast copper alloy, with crutch or butterfly handle,screwed down, screwed for iron pipe, brass ferrule and fixed complete all as specified and directed.

S&F in repair PVC connections 15mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F in repair brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

S&F in repair 20 mm outer dia 3 layer PP-R poly-propylene random copolymer concealed pipes SDR 7.4 (PN-16) UV stabilized and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc., including taking up or down steel tubing and connections complete all as specified and directed.

S&F in repair 25 mm outer dia 3 layer PP-R poly-propylene random copolymer concealed pipes SDR 7.4 (PN-16) UV stabilized and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc., including taking up or down steel tubing and connections complete all as specified and directed.

S&F in repairs Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes including beding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mmx 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

S&F Stainless steel plate rack 1 mm thick of size 760x930x200 mm of standard makes complete all as specified and directed.

M&L preparing new or previously untreated surfaces of wood and wood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L preparing new or previously untreated surfaces of steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide,zinc chrome primer complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls and applying two coats of exterior weather coat paint over a coat of primer of surfaces complete all as specified and directed.

M&L preparing surfaces plastered or unplastered old surfaces of walls and applying one coat of exterior weather coat paint complete all as specified and directed.

M&L preparation of newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed.

M&L preparing surfaces plastered or unplastered old ceiling surfaces and applying one coat of white wash complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M&L preparing of old surfaces plastered or unplastered surfaces of walls and applying one coat of white wash complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistant primer completeall as specified and directed.

M&L preparation of old painted surfaces of walls and applying one coat of oil bound distemper complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls or laid in floors as in soil, waste and vent pipes including dismantling of old pipes complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) bends any radius provided with access door, complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) junction, single (Single T) equal or unequal provided with access door, complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) Vent cowl complete all as specified and directed.

S&F in repair 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls or laid in floors as in soil, waste and pipes complete all as specified and directed.

S&F in repair 75 mm bore PVC (SWR) bends any radius provided with access door,complete all as specified and directed.

S&F in repair 75 mm bore PVC (SWR) Vent cowl complete all as specified and directed.

S&F in repair PVC (SWR) floor trap with diameter of outlet 75mm dia plain with grating including jointing with solvent cement ,complete all as specified and directed.

M&L for Chipping of slab/columns/beams/chajjas/ parapet and removing loose mortar with chisel hammer without much impact concrete and cleaning the exposed reinforcement with wire brush and sand blasting the surface using river sand with minimum of 6 Kg pressure at the nozzle end by mechnical compressor and proiding zinc rich primer at the rate of 5 Sqm/Ltr with Shaliprime zn R to reinforcement as per manufacturers instructions and including all scaffolding, machinery, tools tackles and men, materials and clearing of debries complete all as specified and directed by Engr-in-Charge. Make : Shaliprime zn R of STP or equivalent brand in Fosroc/Dr. Fixit.

M&L providing weld mesh size 100 x 100 x 3mm weld mesh and the mesh with shear connectors with 8mm dia reinforcement by drilling 75mm deep anchoring holes and filled with epoxy resign 20gm/hole with Shaligrout Anchor as per manufacturers instruction including all necessary scaffolding, machinery, tools tackles and men, materials complete all as specified and directed by Engr-in-Charge. Make : Shaligrout Anchor of STP or equivalent brand in Fosroc/Dr. Fixit.

M&L providing drilling of 10mm dia and 100mm deep holes in existing columns/ beams/slabs and providing 8mm dia reinforcement to the slab @ 300mm c/c and shear connectors anchoring with epoxy resign 50gm/hole with Shaligrout Anchor as per manufacturers instruction including all necessary scaffolding, machinery, tools tackles and men, materials complete all as specified and directed by Engr-in-Charge. Make : Shaligrout Anchor of STP or equivalent brand in Fosroc/Dr. Fixit. Note :- Reinforcement shall be measured and paid at "Supply only rate" separately under serial item No. 95.1)

Supply only 8mm dia TMT bars cut to length and shape required for serial item No. 95 above complete all as specified and as directed by Engineer-in- Charge.

M&L providing cement mortar 1:3 by gunniting with gunniting compressor hopper of 50mm thickness ( in two layers of 25 mm thick each layer) mixed with poly propelling fibres and silica fumes @ 0.5 Kgs per bags of cement including all necessary scaffolding, machinery tools tackles, men materials and finishing the surfaces even and smooth, without using extra cement plumb and making surface true to geometry in line complete all as specified and directed by Engr-in-Charge.

Taking down and removing of existing water proofing treatment of any description completely, taking down of old cement plaster if any or roughening of surfaces and cleaning the top surface of RCC slab with using wire brushes and water to remove all dust and loose particles etc complete all as specified and as directed.

M&L for rendering 15mm thick in cement mortar 1:3 on roof/ concrete surfaces with using water proofing compound as per manufacturer's instructions, surface finished even and smooth without using extra cement complete all as spd and as directed. (Supply only of water proofing compound/admixture shall be measured and paid separately).

Supply only of liquid waterproofing compound of approved make.

M&L water proofing treatment with 4mm thick APP modified membrane weighing not less than 4Kg/Sqm reinforced with non woven polyester matt weighing not less than 160 Gram/Sqm having softening point not less than 140 degree celsius, longitudinal tensile strength not less than 300 N/Sqm, tearing strength of 180 N, laid after applying a coat of Bitumen Emulsion, Primer @ 0.20Kg/Sqm over the thoroughly cleaned surfaces to be water proofed. Membrane shall then be laid with 10Cm side overlaps and 15Cm end laps completely thermo fused by flame torch application as per manufacturer's instructions. Care shall be taken to avoid wrinkles while sticking the membrane on the bitumen surface. A coat of hot blown bitumen 90/15 shall be applied on top of the membrane @ 1.20 Kg/Sqm and finally finished with solar reflective aluminium paint @ 0.10 Kg/Sqm. The water proofing membrane shall be extended upto a height of minimum 30 cm on wall and inserted by cutting groove and filling with bitumen complete all as specified and as directed.

Dismantling of water tanks of capacity exc 250litres & n.exc 500litres and removing to store

S&F rotational moulded polyethylene water storage tanks IS : 12701 - 1996 marked double layered (cylindrical vertical witht threaded top) of 500 Litres capacity hoisted and fixed in position all as specified in SSR Part-I complete all as specified and as directed.

S&F in repairs 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pire and fixed. (Minimum weight 455gms) complete all as specified and directed.

S&F in repairs 32mm dia PVC waste pipe for wash hand basins complete all as specified and directed.

S&F in repairs 40mm dia PVC waste pipe for Kitchen sinks complete all as specified and directed.

S&F in repairs 32mm dia Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc with long screwed shanks and fly nuts, flanged end bedded in red lead cement and other end fixed complete all as specified

S&F in repairs 40mm dia Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc with long screwed shanks and fly nuts, flanged end bedded in red lead cement and other end fixed complete all as specified and directed.

M&L Bitumen blown any grade, applied hot, two coats, to concrete surfaces at the rate of 1.50kg per sqm per coat complete all as specified and directed.

M&L for 10mm thick plaster in CM 1:3 on concrete surfaces of sunken portion of WC, finished the surfaces even and smooth with out using extra cement with using water proofing compoud @ 3kg by weight of cementcomplete all as specified and directed. Note :- WPC shall be measured and paid separately.

S&F in repair Brass chromium plated shower roses 125mm size with or without swivel joints, including fixing to steel pipe or union complete all as specified and directed.

S&F in repair 125X100mm size Salt glazed stoneware gully traps, square or rounded mouthed type 'P' complete all as specified and directed.

E/M Works :- Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting, bulbs etc. removing materials to store for taking credit and making good disturbed surfaces of walls, floors, etc. complete all as specified and as directed.

M&L Point wiring using approved colour coding as per IS (Red,Black and Green for single phase circuits) with 1.5 sqmm nominal cross sectional area, copper conductor unshethed FRLSH cable1100 volts grade ISI marked with valid CML No.single core multistranded cable in and including medium grade concealed PVC conduit not less than 20mm dia and accessories ISI marked with valid CML No.( IS-9573-1983 for conduits and IS-3419-1976 for conduit accessories) and including 2mm thick MS sheet /pressed steel sunken boxes (earth dolly) duly painted with two coats of anti corrosive paint / aluminium paint over a coat of red oxide primer internally and two coats of black bituminous paint over a coat of red oxide primer externally covered with 3mm thick plastic laminated sheet cover for fixing of switches ,sockets and fan regulators etc including 1.5mm nominal cross sectional area PVC insulated copper conductor unshethed FRLSH cable single core multistranded cable as earth continuity wire complete all as specified for :- (a) One light point controlled by one switch

All as per serial item No. 113 above but for One fan point controlled by one switch.

All as per serial item No. 113 above but for One 3 pin socket outlet 5 amps on same board controlled by one switch with 1.5 sqmm size cable.

All as per serial item No. 113 above but for One 3 pin socket outlet 5 amps controlled by one switch on independent board with 1.5 sqmm size cable.

All as per serial item No. 113 above but for One 3 pin socket outlet, 15 amps, controlled by one switch on independent board with 4 sqmm size cable.

All as per serial item No. 113 above but for One light point controlled by two way switch.

All as per serial item No. 113 above but for One bell/buzzer point controlled by one push button.

S&F Switch Piano type 5/6 Amp 01 Way complete all as specified and as directed.

S&F Switch Piano type 5/6 Amp 02 Way complete all as specified and as directed.

S&F Socket outlet 2 in 1, 3 pin, 5 amp flush type complete all as specified and as directed.

S&F Switch socket combination 2 in 1, 5 pin, 5/6 Amp flush type complete all as specified and as directed.

S&F Switch socket combination 5 in 1, 5 pin, 15/16 Amp flush type complete all as specified and as directed.

S&F Bell push, flush type, 5 amp complete all as specified and as directed.

S&F Bell, Ding-Dong AC, 230 volts, single phase complete all as specified and as directed.

S&F Lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendant fittings complete all as specified and as directed.

S & F stepped type electronic fan regulator flush type complete all as specified and as directed.

S&F Ceiling rose, 3 plate /PVC/ polycarbonate, isolated body complete all as specified and as directed.

S&F in repair 4 Feet LED Tube light of 20 Watt Batten with integrated electronic driver having THD < 20%, Burning hours not less than 50000 Hrs and aluminium housing with necessary fixing screws, and connected upto ceiling rose with flexible multicore copper cable and making Good complete all as specified and as directed. Make :- Havells Model - LUMILINEPLUSB20WLED865SPCSS or Crompton model - LDL-20-CDL or C&S Model: LTIC00120WLED/WD or its equivalent in Philips/Wipro.

S&F in repair LED Bulb of 7 Watt, 6500K, 700 lumen, with B22 type holder of min 3 star rated, complete all as specified and as directed. Make:- Havells, Model: LED ADORE 7 W B22 or its equivalent in Crompton/ Philips/ Wipro

Supply and fixing in repair LED street light fitting with and including individual high power 25 watt LED new generation energy saving and environmental friendly long life LED street light made up of pressure die cast alu with secondary optics, suitable for outdoor use IP 66, connected with connecting cable complete all as specified and as directed. Make:- Havells Cat No. ENDURAPEARLSL 25W LED757 SASTOPCMP or Crompton Model - LSTS-25-CDL-M or its equivalent in Phillips/Wipro.

S&F street light brackets made of 25 mm dia G.I. Pipe light grade in shape and angle as directed not exceeding 1.5 mtrs in length fixed to wall with suitable size of M.S. flat iron clamps, 2 Nos, M.S nut & bolt with cup washers, painting to MS material with anti corrisive paint complete all as specified and as directed.

S&F in repair SPN DB Double door 8 way with tray for provision of MCBs, and Dolly for earth and netural complete all as specified and as directed

S&F in repair TPN DB Double door 4 way with tray for provision of MCBs, neutral dolly, earth dolly, complete all as specified and as directed. Note for serial item No.134 & 135 :- The quoted rate shall be inclusive of the cost of dismantling of wall portion for concealing the DB and making good the disturbed portion to match with the existing finish complete.

S&F in repair MCB Four Pole 40 Amps, 10 kA, C Curve complete all as specified and as directed.

S&Fin repair MCB Two Pole 6-32 Amps, 10 kA, C Curve complete all as specified and as directed.

S&Fin repair MCB Single Pole 6-32 Amps, 10 kA, C Curve complete all as specified and as directed.

S&F in repair submain wiring with two run of FRLS single core cable PVC insulated unsheathed cable 1100 volts grade 6 Sqmm copper multistranded conductor including and drawing into Rigid concealed PVC conduit, ceiling including one run of 6 sqmm FRLS PVC insulated unsheathed multistranded for earth wire connected to earth, making good, complete all as specified and as directed. Note :- Three run of 6 sqmm cable and onerun of PVC Conduit shall be measured as one RM.

Taking down carefully ceiling fan complete of any size and capacity, Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc and refixing the same with new set of bolts and split pins complete all as directed and as specfied.

Taking down carefully exhaust fan with louver complete of any size and capacity, Painting of fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc and refixing the same fan with new louver complete all as directed and as specfied.

Supply & fix heavy duty Metal Body exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver, connecting wire upto ceiling rose, including necessary civil work like making hole, plastering, finishing complete all as specified and as directed. Make: Crompton, Model: Trans Air 12" or Havells, Model: Ventil Air-DB or its equivalent in Almonard/ Bajaj

M&L Earthing complete with earth galvanized steel plate electrode 600x600x6mm buried directly in ground earth pit not less than 2.25 mtr below ground level with top edge of the plate not less than 1.5 mtr below ground level, surrounded from all sides with mixture of charcoal and common salt and electrode connected with galvanized earth lead GI wire 4 mm dia by means of bolts, check nut and washers of GI or steel, GI pipe light grade of 15 mm bore as protection pipe, GI wire of length not more than 7.5 mtr and connected to test point. GI pipe 20mm dia medium grade for watering, funnel with wire mesh, PCC pit and RCC (1:2:4) type B-1 for cover with 8 mm dia bar reinforcement both ways @ 140 c/c including excavation and earth work disposal of surplus soil to a distance not exceeding 50 mtr as shown on electrical plate No 3 of SSR 2009 complete all as specified and as directed.

S&F Full smart functionality single phase, two wire 240 V ,10-60 A Class 1.0 Accuracy smart Energy meter with inbuilt connect /disconnect facility and communication module complying with IS-16444. The meter shall have biderectional communication capability through any of the communication technologies defined in IS 16444 including optical,RF and GPRS. ISI marked smart meter with provision of TOD ( Time of Day) tariff, suitable for measurement of energy (kWH & kVAh) and demand (kW & kVA). The meter can function in both Postpaid and prepaid mode, any mode can be enabled remotly. The meter can be connected/disconnected remotely through software. Load connection / disconnection via relays in phase and neutral. Tamper alerts available,data logging for instsntaneous parameters, billing parameters and energy backups,event logging with active energy, voltage and current snaps, power fail alerts, including sealing facility complete all as specified and as directed. Make :- L&T /HPL/Secure/ABB Note: The quoted rate shall be inclusive of taking down of existing energy meter and handing over to MES BS Section.

Supply, fixing and commissioning of GW 2000 Gateway (MQTT With 16 GB Memory) Make: Elmeasure or equivalent of L&T/ Havells/ Bentec/ Secure

Supply, fixing and commissioning of ELNet V5 Pro-50 Nos with Web based application configuring and linking of each meter with Elnet Software for communicating with meters (Software with lifetime license) including provision of Auto invoice generating and auto email of energy bills to users all as directed optional future energy data export to MES ERP Make: Elmeasure or equivalent of L&T/Havells/ Bentec/ Secure

Supply and laying of CAT 6 Cable D link 300 Meters Make: Dlink or equivalent of L&T/ Havells/ Bentec/ Secure

Supply and fixing Meter Enclosure box on wall with minimum space of accommodation of 01 Nos of energy meter indoor cubicle type wall mounted, vermin proof, dust proof, powder coated made out of CRCA Sheet Not less than 1.6 mm thick powder coated paint suitable complete all as specified and as directed.

Supply and installation of Computer with Intelcore i5 8th Gen processor 8500 Q370 Chipset motherboard (4 DIMM Slot) and following: (i) 8 GB DDR 4 Ram (Support upto 64 GB) (ii) 1 TB Hard Disk (iii) DVD RW (iv) 19.5 TFT monitor (E2016H) (v) Windows 10 professional (vi) Dell/HP Keybord and Mouse (vi) 3 Years Warranty Make: Dell/ HP / Acer

Supply and installation of Microsoft MS Office Home and Business 2019 or latest complete.

M/s. P S REDDY

M/s RAMA LAKSHMI CONSTRUCTIONS

Behl construction co.