REPAIR / REPLACEMENT OF POINT WIRING AND ITS CONNECTED IN ZONE-07, 08 AND 09 AT NAA UNDER GE (NORTH) TEZPUR

Amount

Note 1: (Applicable for all parts/items) : The bidders/contractors are advised to read tender document, all drawings & all corrigendum/amendments and general condition of contracts before entry/quoting the rates. Note 2:- Attention to bidder is hereby invited to upload revised BOQ if published during their bid submission. Uploading of incorrect/ pre-revised BOQ shall be treated as non bonafide and rejected. Fixed credit has been given in technical documents which shall be taken into account during acceptance of bid/tender.

Dismentaling and taking down carefully aluminium / copper point wiring complete including fitting / fixtures such as switches, ceiling roses, holder, socket, light fitting etc; and making good disturbed surfaces of walls, ceilings etc all as specified.

Dismantaling and taking down burntout submain wiring including conceled /surface counduite ,PVC Cassing capping and making good to the disturbed surfaces of wall etc.All asspecified and directed.

Dismantaling and taking down old burnt/unserviceable main switches and DB's including MCB SP/SPN/TPN of any make and any size, wooden board, junction box and making good distrubed surfaces of wall all as directed.

Material and labour for point wiring with 1.5 sqmm (nominal area) FRLS PVC insulated stranded copper conductor cable 1100 volts grade single core confirming to IS-694-1990 with and including one run of continous earth wire of 1.5 sqmm core PVC insulated unsheathed stranded copper conductor cable draw in & including PVC surface casing 'N' capping not less than 20mm wide double lock type to be fixed with the help of rawalplugs and screws including necessary fitting, and fixtures including PVC terminal box and PVC baord making good disturbed surface with CM (1:4) to match with the existing surface complete.

For one light/fan/bell/exhaust fan point controlled by one way switch complete all as specified and directed.

For 5 Amps Socket point on independent board with 1.5 sq mm copper cable complete all as specified and directed.

For 5 Amps Socket point on same board with 1.5 sq mm copper cable controlled by one other 5 Amp switch complete all as specified and directed.

For 15 Amps Socket point on independent board with 2.5 sq mm copper cable complete all as specified and directed.

For two way wiring with 1.5 sq mm copper cable complete all as specified and directed.

M&L for switch piano (flush button type) single pole, one way, 5 Amps complete all as specified and directed.

M&L for switch piano (flush button type) single pole, two way, 5 Amps complete all as specified and directed.

M&L for switch socket combination 2 in one, 5 Amps 240 volts flush type complete all as specified and directed.

M&L for switch socket combination 2 in one, 6 pin 6 Amps and 16 Amps flush type complete all as specified and directed.

S&F socket out let , 5 pin 5 Amps flush type complete all as specified and directed.

S&F switch bell push flush type 5 Amps complete all as specified and directed.

S&F call bell ding dong AC 230 Volts complete all as specifie and directed.

S&F ceiling rose Polycarbonate two to three terminals complete all as specified and directed.

S&F Lamp Holder,PVC/ polycarbonate complete all as specified and directed

S&F electronic fan regulator step typy 5 module complete all as specified and directed.

S&F LED Tubelight fitting, 1x18W, 230v, Lumeno, epoxy powder coated CRCA sheet housng with reflector cover channel, with elecronic driver, connetor blocks etc, complete with all as specified and including connecting up with three core twisted flexible copper conductor cable suitable size complete all as specified and directed Model No.BCLSB 18 WH of Bajaj or Equivalent

S&F LED wall security lights of 15W with necessary brackets (made out of 25mm bore GI pipe light grade appx 0.6 meter long bend to shape) nuts, bolts, etc to be fixed on walls complete all as specified and directed Make:- Bajaj Cat Pat No. BCLST 15W LED Product No 169828 or equivalent model of Havells/Philips

S&F sheet metal enclosures factory fabricated for Multiphase Out going suitable for Mounting MCCB as incomer of rating 63Amp Vertical distribution board 4 way with suitable Amp rated bus bar having lP-42 protection and double metal door concealed / mounted in wall including connection with aluminium thimbles as required complete all as specified. Cat No-DBVTL00454 of L&T or Equivalent Model of other Make as Approved by GE. (Note : MCCB & MCB Shall be Measured and Paid Separately)

M&L for sheet metal double door enclosure MCB DBs SPN 8 way 240 V, complete flush mounted all as specified and as directed.

M&L for sheet metal double door enclosure MCB DBs SPN 4 way 240 V, complete flush mounted all as specified and as directed.

M&L for Isolator/MCB single pole 5 to 40 Amps, 240 volts complete all as specified and directed.

M&L for MCCB, AC 440V, 63 Amp, 25 KA, 4 Pole including complete electrical connection by proper size of copper lugs complete all as specified and directed by the Engr-in-Charge.

M&L for Isolator/MCB DP 32 Amps, 240 volts complete all as specified and directed.

M&L for submain wiring with two run of 6 sq mm FRLS PVC insulated stranded copper conductor cable 1100 volts grade drawn through and including PVC casing and capping of suitable size with all fittings and accessories including one run of 6 sq mm FRLS PVC insulated stranded copper cable for earth continuity and connected to common earth dolly complete all as specified and directed.

M&L for submain wiring with two run of 6 sq mm FRLS PVC insulated stranded copper conductor 1100 volts grade in existing concealed/surface PVC conduit including 6 sq mm FRLS PVC insulated stranded copper conductor cable for earth continuity and connected to common earth dolly complete and making good disturbed surface complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick buried directly in ground ( earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less than 1.5 Metre below normal ground level connected to GI wire 4 mm dia by means of bolts, nuts , check nuts and washers of GI and GI tubing 15 mm bore light grade for earth lead protection up to main earth test point and including concrete pit in PCC (1:3:6) type C1 pre cast RCC (1:2:4) type B1 cover slab 54 x 54 x 5 cm with one handle for lifting made out of 8 mm dia MS bar, wire mesh, 20 mm bore GI tubing (LG) for watering, charcoal or coal and salt in alternate layers including excavation earth work complete all as shown on electrical plate No. 3 of SSR part - I complete alll as specified and directed.

S&F single pole and netural enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps, 240V complete all as specified.

Supply and fixing AC single phase static energy meter of accuracy class 1.0, 240V, 50Hz with Backlit LCD display of rating 5-30A, with optical port + Box (measures and display KWH, V, Current I, KW, PF last month history of KWH, MD in KW) with special features like TOD, temper logging, optical communication port display in absence of power with polycabonate transparent hinge type meter box, complete all as specified and directed. Cat No : WM101BC5DHBOX of make L&T or equivalent in secure.

Supply and fixing AC Three phase static energy meter of accuracy class 1.0, 240V, 50Hz with Backlit LCD display of rating 10-60A, with optical port + Box (measures and display KWH, V, Current I, KW, PF last month history of KWH, MD in KW) with special features like TOD, temper logging, optical communication port display in absence of power with polycabonate transparent hinge type meter box, complete all as specified and directed. Cat No : WR300BC73BOXH of make L&T or equivalent in secure.

M & L for detecting faults in L T electric supply distribution system in OTM /Md accn in the restricted area of Solmara NAA and rectifiying the defects for restoring supply including replacing of unserviciable defective electrical accessories Note :- (i) Spares shall be measured and paid under respective item of schedule . (ii) Essential meterial like, insulation tape,screws and all tools required for carrying out the works and insutruments to the defect fault shall be deemed to be included in the quoted rate

Supply in replacement switch piano (flush button type) single pole, one way, 5 Amps complete all as specified and directed.

Supply in replacement switch piano (flush button type) single pole, two way, 5 Amps complete all as specified and directed.

Supply in replacement switch socket combination 2 in one, 5 Amps 240 volts flush type complete all as specified and directed.

Supply in replacement switch socket combination 2 in one, 6 pin 6 Amps and 16 Amps flush type complete all as specified and directed.

Supply in replacement socket out let , 6 pin 5 Amps flush type complete all as specified and directed.

Supply in replacement switch bell push flush type 5 Amps complete all as specified and directed.

Supply in replacement call bell ding dong AC 230 Volts complete all as specifie and directed.

Supply in replacement ceiling rose Polycarbonate two to three terminals complete all as specified and directed.

Supply in replacement Lamp Holder,PVC/ polycarbonate complete all as specified and directed

Supply in replacement stepped type electronic fan regulator 2 module complete all as specifed by Engr-in-Charge.

Supply in replacement plug top, 3 pin 6 Amps 220/230volts complete all as specifie and directed.

Supply in replacement plug top, 3 pin 15/16 Amps 220/230volts complete all as specifie and directed.

Supply in replacement of hylam sheet cover 3 mm thick for fixing switches, sockets, regulators etc of size 4 x 4 (Inches) on existing metal box complete all as specified and directed.

Supply in replacement hylam sheet cover 3 mm thick for fixing switches, sockets, regulators etc of size 7 x 4 (Inches) on existing metal box complete all as specified and directed.

Supply in replacement hylam sheet cover 3 mm thick for fixing switches, sockets, regulators etc of size 8 x 6 (Inches) on existing metal box complete all as specified and directed.

Supply in replacement hylam sheet cover 3 mm thick for fixing switches, sockets, regulators etc of size 10 x 12 (Inches) on existing metal box complete all as specified and directed.

Supply in replacement of three core twisted flexible cable, PVC insulated with stranded copper conductor of size 23/0.0076, AC 1100 volts grade complete all as specified and directed.

Supply in replacement of Threaded type CFL lamp, 5 W (DU) with E-14 base, Cat No. PHHDC14005 Make : Havells or equivalent approved make of Bajaj/Philips complete all as specified and directed.

Supply in replacement of LED Bulk Head luminaire, 10 watts, complete Luminaire type, BIBWP 10W LED of Bajaj or equivalent approved make of Havell's Crompton/Philips complete all as specified and directed.

Supply in replacement of 4 pin type PLL lamp base, LED PLL Lamp,18 W Product code: HPLLEDPL18W(CW) Make : HPL or equivalent approved make of Bajaj/Philips/Havell's complete all as specified and directed.

Supply and fixing in replacement of fan capacitor, AC 230 V, 2.5 MFD complete all as specified and directed.

Supply and fixing in replacement of fan capacitor, AC 230 V, 3.15 MFD complete all as specified and directed.

Supply and fixing in replacement of PVC conduit medium grade with fittings, ISI marked, 20 mm size complete all as specified and directed.

Supply and fixing in replacement of PVC conduit medium grade with fittings, ISI marked, 25 mm size complete all as specified and directed.

Supply and fixing in replacement of PVC casing & capping with fittings, ISI marked, 20 mm size complete all as specified and directed.

Supply and fixing in replacement of PVC casing & capping with fittings, ISI marked, 25 mm size complete all as specified and directed.

Supply and fixing in replacement of PVC switch boards, closed recessed suitable for surfaces, sizes 4 X 4 (Inches) complete all as specified and as directed.

Supply and fixing in replacement of PVC switch boards, closed recessed suitable for surfaces, sizes 4 X 7 (Inches) complete all as specified and as directed.

Supply and fixing in replacement of PVC switch boards, closed recessed suitable for surfaces, sizes 8 X 6 (Inches) complete all as specified and as directed.

Supply and fixing in replacement of PVC switch boards, closed recessed suitable for surfaces, sizes 8 X 10 (Inches) complete all as specified and as directed.

Supply and fixing in replacement of PVC insulated copper conductor cable, FRLSH, single core, 1100 Volts, 1.5 Sq mm complete all as specified and directed.

Supply and fixing in replacement of PVC insulated copper conductor Cable, FRLSH, single core, 1100 Volts, 2.5 Sq mm complete all as specified and directed.

Supply and fixing in replacement of PVC insulated copper conductor Cable, FRLSH, single core, 1100 Volts, 4.0 Sq mm complete all as specified and directed.

Supply and fixing in replacement of PVC insulated copper conductor Cable, FRLSH, single core, 1100 Volts, 6.0 Sq mm complete all as specified and directed.

Taking down ceiling fan any type/ size from hook and dismantling cable and blades and bring in to store for repair and hanging ceiling fan in position after repair, greasing etc. with existing flexible copper cable complete all as directed. (rewinding of fan, painting and spare parts required shall be measured and paid separately)

Taking down exhaust fan any type/ size from wall and dismantling sealing cable and dismantling blades and bring in to store for repair and fixing exhaust fan in position after repair, greasing etc. with existing flexible copper cable complete all as directed. (rewinding of fan, painting and spare parts required shall be measured and paid separately)

M&L for rewinding of ceiling fan 1200 mm sweep after dismantlingand taking out the burnt winding coils and rewinding with super enamelled copper winding wire of suitable size and gauge including insulation, Varnishing, drying etc complete and refixing the same after rewinding and testing complete all as specified and directed.

All as item No 67.00 above but 1400 mm sweep ceiling fan

All as item No 67.00 above but exhaust fan 300mm to 450 mm sweep

Suply and Fixing brass bush for ceiling fan / Exhaust fan as existing size .

Supply and Fixing bearing suitable for ceiling fan 1200mm to 1400mm /exhaust fan of bearing No- 6201/6202 Make-Tata/SKF/NBC

Suply and fixing capacitor 4.0 MFD for exhaust fan.

M&L for painting of ceiling fans / Exhaust fan with blade complete insitu with synthetic enamelled paint by spraying includingfilling cavities with filler, one coat after cleaning all dust etc all as specified and directed.

Taking down carefully water heater storage type of any capacity from its position for repair/ overhauling by disconnecting complete electric/water supply connections, taking out geyser assembly repairing by minor welding of inner tank re-assembling the geyser and refixing the same by connecting electric / water supply connections and testing complete all as specified and directed (spares will be measured and paid separately)

M&L for taking out the old u/s element and fixing of new heating element of capacity 2 KW of any type (as per sample). Make: Bajaj/Recold/GEC

M&L for taking out the old u/s thermostate for geyser and fixing of new thermostate adjustable between 30 degree to 90 degree celcius of any size /type as per existing (ISI marked)

M&L for taking out the old u/s indicator lamp and fixing of new indicator lamp of suitable capacity including its electrical connection.

M&L for replacement of PVC connection heavy duty 450mm long with 2 nuts brass at both ends suitable for hot water for GI pipe 15 mm dia complete all as specified and directed

M&L for replacement of stainless steel inner tank for geyser of capacity 25 Ltr (as per sample) complete all as directed by Engineer -in - charge

M&L for MS anchor fastener heavy duty 12mm dia 10 cm long all as directed.

M&L for painting of geyser 25/50 ltr complete insitu with synthetic enamelled paint by spraying includingfilling cavities with filler, one coat after cleaning all dust etc all as specified and directed.

M/S Manjit Singh

M/S MOHANPASARI

Shree Krishna Traders