Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹40.0 LAccepted-AOC H NO 05 AASI BAUG OPP VATSALYA SCHOOL BHUJ KUTCH 370001 | BHUJ | KUTCH | GUJARAT | 370001 | ₹40.0 L Quoted ₹42.1 L | L1 | Accepted-AOC BEING LOWEST |
| 2 | L2₹44.8 L+₹2.7 L (6.47%)Rejected-Finance WANIAWAD BHUJ KUTCH 370001 | BHUJ | KUTCH | GUJARAT | 370001 | ₹44.8 L+₹2.7 L (6.47%) | L2 | Rejected-Finance BEING NOT LOWEST |
| Sl No | Description | Qty | Unit | M/s Bombay Novelty Stores L2 | Ahmed B Khatri L1 |
|---|---|---|---|---|---|
| 1.00 | Disconnecting the water mains from the delivery line of submersible motor and pumping sets,including disconnecting electric connections, lifting & taking out HDPE/GI/UPVC column pipes 80/100/110 mm dia bore, submersible cable and defective submersible pumping set with connected cage,seperating pump and motor for repair purpose,etc. for necessary repairs (Repairs to be measured and paid for separately under respective items here in after) ,re-assembling pump and motor after repairslowering of repaired / replaced HDPE/GI/UPVC column pipes 80/100/110mm dia bore, submersible cable, submersible pumping sets complete in bore well, jointing of submersible cable, reconnecting delivery line to water mains, testing for satisfactory running and continuous flow of water complete all as specified and directed by Engineer-in-Charge. | 30 | EACH JOB | 5,000 ₹1,50,000 Lowest | 5,000 ₹1,50,000 Lowest |
| 2.00 | Material & labour for unserviceable MS nuts, bolts and washers of any size & length as required at site and as directed for hold fastening column pipes/centrifugal pump and motor set complete all as specified and directed by Engineer-in-Charge. | 40 | KILOGRAM | 107 ₹4,280 Lowest | 120 ₹4,800 |
| 3.00 | Transporting defective submersible motor of any make and capacity of 30 HP to workshop, material & labour for dismantling motor, taking out burnt copper winding of stator,cleaning the casing and stator with wire brush and cleaning the surface, rewinding the motor using super enameled insulated copper winding wire of existing gauge, insulating & drying , complete re-assembling the motor to its original form after replacement of defective parts and testing for satisfactory run, bringing back to site of work complete all as specified and directed by Engineer-in-Charge.
Note :(i) Supply & fix in replacement of defective parts and remetaling, turning & polishing of motor shaft shall be measured and paid separately under respective items here-in-after.
(ii) Rate quoted by the tenderer is deemed to include the cost for replacement of minor parts like nuts, bolts, washers, etc | 2 | EACH JOB | 23,750 ₹47,500 Lowest | 25,000 ₹50,000 |
| 4.00 | Transporting defective submersible motor of any make and capacity of 40 HP to workshop, material & labour for dismantling motor, taking out burnt copper winding of stator,cleaning the casing and stator with wire brush and cleaning the surface, rewinding the motor using super enameled insulated copper winding wire of existing gauge, insulating & drying , complete re-assembling the motor to its original form after replacement of defective parts and testing for satisfactory run, bringing back to site of work complete all as specified and directed by Engineer-in-Charge.
Note :(i) Supply & fix in replacement of defective parts and remetaling, turning & polishing of motor shaft shall be measured and paid separately under respective items here-in-after.
(ii) Rate quoted by the tenderer is deemed to include the cost for replacement of minor parts like nuts, bolts, washers, etc | 2 | EACH JOB | 29,450 ₹58,900 | 28,000 ₹56,000 Lowest |
| 5.00 | Transporting defective submersible motor of any make and capacity of 50 HP to workshop, material & labour for dismantling motor, taking out burnt copper winding of stator,cleaning the casing and stator with wire brush and cleaning the surface, rewinding the motor using super enameled insulated copper winding wire of existing gauge, insulating & drying , complete re-assembling the motor to its original form after replacement of defective parts and testing for satisfactory run, bringing back to site of work complete all as specified and directed by Engineer-in-Charge.
Note :(i) Supply & fix in replacement of defective parts and remetaling, turning & polishing of motor shaft shall be measured and paid separately under respective items here-in-after.
(ii) Rate quoted by the tenderer is deemed to include the cost for replacement of minor parts like nuts, bolts, washers, etc | 4 | EACH JOB | 34,140 ₹1,36,560 | 30,000 ₹1,20,000 Lowest |
| 6.00 | Material & labour for remetalling turning & polishing of motor shaft including lathe work of submersible motor of capacity 30 to 50 HP complete all as specified and directed by Engineer-in-Charge. | 8 | EACH JOB | 800 ₹6,400 Lowest | 800 ₹6,400 Lowest |
| 7.00Supply only in replacement of following defective parts of submersible motor of capacity 30 to 50 HP complete all as specified and directed by Engineer-in-Charge. (Note - (i) The original parts as provided by the manufacturer only be used in the work. (ii) The work is to be carried out on the motors dismantled under item No 3 to 5 above) : - | |||||
| 7.01 | Bearing bush gun metal | 10 | EACH | 740 ₹7,400 | 700 ₹7,000 Lowest |
| 7.02 | SS Sleeve for shaft | 10 | EACH | 635 ₹6,350 | 550 ₹5,500 Lowest |
| 7.03 | Oil Seal. | 10 | EACH | 242 ₹2,420 | 150 ₹1,500 Lowest |
Tender Value
₹45 L
EMD Value
₹90,000
Closing Date
26 Jun 2025, 6:00 pmClosed
GE (AF) BHUJ
GE (AF) BHUJ ,KHAVDA ROAD, BHUJ GUJARAT-370001
REPAIRS/MAINTENANCE OF SUBMERSIBLE PUMP SETS AND CENTRIFUGAL PUMP SETS INCLUDING PANELS, STARTER AND OTHER MISC CONNECTED ITEMS AT AF STN BHUJ
2025_MES_710067_1
8818/V/E8
Open Tender
Electrical and Maintenance Works
Item Rate
270 days
GE (AF) BHUJ
AS PER NOTICE OF TENDER
7 documents required · 7 mandatory
₹500
GE (AF) BHUJ
₹90,000
Yes
26 Aug 2025
24 May 2025
28 Jun 2025
24 May 2025
26 Jun 2025
14 Jun 2025
27 May 2025 - 29 May 2025
Amount
Disconnecting the water mains from the delivery line of submersible motor and pumping sets,including disconnecting electric connections, lifting & taking out HDPE/GI/UPVC column pipes 80/100/110 mm dia bore, submersible cable and defective submersible pumping set with connected cage,seperating pump and motor for repair purpose,etc. for necessary repairs (Repairs to be measured and paid for separately under respective items here in after) ,re-assembling pump and motor after repairslowering of repaired / replaced HDPE/GI/UPVC column pipes 80/100/110mm dia bore, submersible cable, submersible pumping sets complete in bore well, jointing of submersible cable, reconnecting delivery line to water mains, testing for satisfactory running and continuous flow of water complete all as specified and directed by Engineer-in-Charge.
Material & labour for unserviceable MS nuts, bolts and washers of any size & length as required at site and as directed for hold fastening column pipes/centrifugal pump and motor set complete all as specified and directed by Engineer-in-Charge.
Transporting defective submersible motor of any make and capacity of 30 HP to workshop, material & labour for dismantling motor, taking out burnt copper winding of stator,cleaning the casing and stator with wire brush and cleaning the surface, rewinding the motor using super enameled insulated copper winding wire of existing gauge, insulating & drying , complete re-assembling the motor to its original form after replacement of defective parts and testing for satisfactory run, bringing back to site of work complete all as specified and directed by Engineer-in-Charge. Note :(i) Supply & fix in replacement of defective parts and remetaling, turning & polishing of motor shaft shall be measured and paid separately under respective items here-in-after. (ii) Rate quoted by the tenderer is deemed to include the cost for replacement of minor parts like nuts, bolts, washers, etc
Transporting defective submersible motor of any make and capacity of 40 HP to workshop, material & labour for dismantling motor, taking out burnt copper winding of stator,cleaning the casing and stator with wire brush and cleaning the surface, rewinding the motor using super enameled insulated copper winding wire of existing gauge, insulating & drying , complete re-assembling the motor to its original form after replacement of defective parts and testing for satisfactory run, bringing back to site of work complete all as specified and directed by Engineer-in-Charge. Note :(i) Supply & fix in replacement of defective parts and remetaling, turning & polishing of motor shaft shall be measured and paid separately under respective items here-in-after. (ii) Rate quoted by the tenderer is deemed to include the cost for replacement of minor parts like nuts, bolts, washers, etc
Transporting defective submersible motor of any make and capacity of 50 HP to workshop, material & labour for dismantling motor, taking out burnt copper winding of stator,cleaning the casing and stator with wire brush and cleaning the surface, rewinding the motor using super enameled insulated copper winding wire of existing gauge, insulating & drying , complete re-assembling the motor to its original form after replacement of defective parts and testing for satisfactory run, bringing back to site of work complete all as specified and directed by Engineer-in-Charge. Note :(i) Supply & fix in replacement of defective parts and remetaling, turning & polishing of motor shaft shall be measured and paid separately under respective items here-in-after. (ii) Rate quoted by the tenderer is deemed to include the cost for replacement of minor parts like nuts, bolts, washers, etc
Material & labour for remetalling turning & polishing of motor shaft including lathe work of submersible motor of capacity 30 to 50 HP complete all as specified and directed by Engineer-in-Charge.
Supply only in replacement of following defective parts of submersible motor of capacity 30 to 50 HP complete all as specified and directed by Engineer-in-Charge. (Note - (i) The original parts as provided by the manufacturer only be used in the work. (ii) The work is to be carried out on the motors dismantled under item No 3 to 5 above) : -
Bearing bush gun metal
SS Sleeve for shaft
Oil Seal.
Brass thrust plate
CI Thrust bearing
CI housing bearing bush gun metal
Stainless steel sand guard
CI lower housing for resting of shaft.
CI upper housing for resting of shaft
CI connecting piece at drive end
Transporting defective pump of 30 to 50 HP capacity submersible pumping set to work shop, dismantling of pump, andbringing back to site of work and testing for satisfactory running complete all as specified and directed by Engineer-in-Charge. (Note - (i) Supply & fix in replacement of parts shall be measured and paid for separately under respective items here in after. (ii) Rate quoted by the tenderer is deemed to include the cost for replacement of minor parts like nuts, bolts, washers, etc.
Supply & fix in replacement of following defective parts of submersible pump of 30 to 50 HP capacity complete all as specified and directed by Engineer-in-Charge. Note - (i) The original parts as provided by the manufacturer shall only be used in the work. (ii) The work is to be carried out on the pumps dismantled under item No 8 above : -
CI stage casing
Bearing bush rubber
Stainless Steel sleeve at staging
SS impellers
Neck ring brass
Key for impellers
NRV body of pump
MS stud with nuts of size of 3/8" X 2" for stage casing
Bush gun metal at intermediate section
Steel sleeve at intermediate section
CI intermediate section
SS Shaft of suitable size
Material & labour for brazing of submersible motor rotor of capacity 30 HP to 50 HP complete all as specified and directed by Engineer-in-Charge. Note:- The work is to be carried out on the pumps & motor dismantled under item No 01 above
Supply & fix in replacement of unserviceable stainless steel coupling & key common for submersible pump and motor shaft complete all as specified and directed by Engineer-in-Charge. (Note - (i) The original parts as provided by the manufacturer shall only be used in the work. (ii) The work is to be carried out on the pumps dismantled under item No 01 above).
Supply & fix in replacement of suitable size of cage (approximately weight 30Kg each), fabricated out of mild steel flat iron 50 X 6 mm to hold the submersible pumping set alongwith motor safely as per existing pattern and as approved by Engineer-in-Charge complete all as specified and directed by Engineer-in-Charge. (Note:-The work is to be carried out on the pumps & motors dismantled under item No 01 above).
Supply & fix in replacement of PVC air release valve 25 mm bore with & including required length & size of PVC/GI pipe complete all as specified and directed by Engineer-in-Charge.
Supply & fix in replacement of submersible flat copper stranded cable 1100 Volt grade of size 25 sqmm 3 core complete all as specified and directed by Engineer-in-Charge.
Material & labour for mild steel bore well cap for existing bore hole size in two parts 6mm thick with cable/column pipe entry system and locking arrangements and welding works as in repair complete all as specified and directed by Engineer-in-Charge.
Material & labour for development of tube well by compressed air with compressor of minimum capacity of 100 PSI and 450 CFM complete all as specified and directed by Engineer-in-Charge. Note:- (i) Yield test for the bore well by continuously pumping to determine safe pumping yield to be carried out by contractor at site and necessary report to be submitted. (ii) Testing of water for potability, dissolved solids, physical/chemical and bactorogical testing etc from the govt lab shall be carried out by the contractor all as directed and test report shall be submitted.
Disconnecting the electric connection of the defective electric motor of any make from panel board, disconnecting from centrifugal pumping set, Transporting to work shop and dismantling motor, taking out burnt copper winding of stator, cleaning the casing stator with wire brush, repair to rotor by turning , polishing and turning, rewinding the motor using PVC insulated copper wire of existing gauge bringing back to site of work, reconnecting electrical connection , recoupled with centrifugal pumping set, testing for satisfaction running to the satisfactory of complete all as specified and directed by Engineer-in-Charge for following capcities of motors : - Note: (i) Rate quoted by contractor is deemed to be inclusive of minor spares like gland, grease, nut bolts and major spares required for work shall be measured and paid separately and rate quoted shall be deemed to be inclusive of fixing charges of major new spares under this item. (ii) Contractor should visit site before quoting the rates. (iii) Cost of transportation shall be deemed to be included in the rate quoted for these items. (iv) While taking out pump for repairs , the contractor shall make arrangement for pluging suction and discharge line with dead flanges without extra cost, so that pumping of installation is not disturbed and there is no leakage of water.
60 HP Capacity
40 HP Capacity
30 HP Capacity
20 HP Capacity
15 HP Capacity
Disconnecting the centrifugal/monoblock pump of following capacity of any make and model from motor and all water /electrical connections and removing/taking up from foundation, taking to civil authorised dealer workshop for repair/strip opening and repairing of pumping sets by changing the defective/unserviceable parts such as bearing, shaft, impeller, bush, Gland plate etc. complete. Reassembling including oiling, greasing replacement of worn out nuts, bolts, gasket etc, and re-fixing in its original position at site, making all connections, commissioning and testing for smooth and noise free operation etc complete all as specified and directed by Engineer-in-Charge. Notes :- (i). Ball bearing, shaft, impeller, bush, gland plate & stuffing box packing, interstage ring, wear ring, bearing housing, water deflector s/s stud gasket packing etc will be replaced if required and cost for the items shall be measured and paid separately under appropriate item of this BOQ as supply only. (ii) The T & P/vehicles for transportation of centrifugal pump will be arranged by the contractor and the cost deemed to be included in the quoted rate of this item
60 HP Capacity
40 HP Capacity
30 HP Capacity
20 HP Capacity
15 HP Capacity
Supply only shaft sleeve suitable of following capacity centrifugal pump sets complete all as specified and directed by Engineer-in-Charge.
60 HP Capacity
40 HP Capacity
30 HP Capacity
20 HP Capacity
15 HP Capacity
Supply only gland pressure plate with complete MS nut & bolt suitable for centrifugal pump sets of following capacity complete all as specified and directed by Engineer-in-Charge.
60 HP Capacity
40 HP Capacity
30 HP Capacity
20 HP Capacity
15 HP Capacity
Supply only ball bearing of suitable of centrifugal pump sets following capacity complete all as specified and directed by Engineer-in-Charge.
60 HP Capacity
40 HP Capacity
30 HP Capacity
20 HP Capacity
15 HP Capacity
Supply only impeller of suitable of centrifugal pump sets following capacity complete all as specified and directed by Engineer-in-Charge.
60 HP Capacity
40 HP Capacity
30 HP Capacity
20 HP Capacity
15 HP Capacity
Supply only neck ring of suitable for centrifugal pump sets following capacity complete all as specified and directed by Engineer-in-Charge.
60 HP Capacity
40 HP Capacity
30 HP Capacity
20 HP Capacity
15 HP Capacity
Supply only S/S stud and of suitable size for centrifugal pump sets following capacity complete all as specified and directed by Engineer-in-Charge.
60 HP Capacity
40 HP Capacity
30 HP Capacity
20 HP Capacity
15 HP Capacity
Supply only SS shaft of suitable size for centrifugal pump sets following capacity complete all as specified and directed by Engineer-in-Charge.
60 HP Capacity
40 HP Capacity
30 HP Capacity
20 HP Capacity
15 HP Capacity
Material & labour for repairing of mono block pump of capacity 12.5 HP by dismantlling its pump and motor, taking out burnt copper winding of stator, cleaning the casing stator with wire brush,rewinding the motor using new super enamelled copper wire of same guage and with equal number of turns bringing back to site of work, reconnecting electrical connection , recoupled and alinged with monoblock pumping set, testing for satisfaction running to the satisfactory of complete all as specified and directed by Engineer-in-Charge.. Note:-(i) Spare parts of monoblock pump set will be measured and paid seperately under relevant items of this schedule. (ii) T & P/vehicles for transportation of monoblock pump and motor will be arranged by the contractor and the cost deemed to be included in the quoted rate of this item (iii) While taking out pump for repairs , the contractor shall make arrangement for pluging suction and discharge line with dead flanges without extra cost, so that pumping of installation is not disturbed and there is no leakage of water
Material & labour for repairing of mono block pump of capacity 10 HP by dismantlling its pump and motor, taking out burnt copper winding of stator, cleaning the casing stator with wire brush,rewinding the motor using new super enamelled copper wire of same guage and with equal number of turns bringing back to site of work, reconnecting electrical connection , recoupled and alinged with monoblock pumping set, testing for satisfaction running to the satisfactory of complete all as specified and directed by Engineer-in-Charge.. Note:-(i) Spare parts of monoblock pump set will be measured and paid seperately under relevant items of this schedule. (ii) T & P/vehicles for transportation of monoblock pump and motor will be arranged by the contractor and the cost deemed to be included in the quoted rate of this item (iii) While taking out pump for repairs , the contractor shall make arrangement for pluging suction and discharge line with dead flanges without extra cost, so that pumping of installation is not disturbed and there is no leakage of water
Material & labour for repairing of mono block pump of capacity 7.5 HP by dismantlling its pump and motor, taking out burnt copper winding of stator, cleaning the casing stator with wire brush,rewinding the motor using new super enamelled copper wire of same guage and with equal number of turns bringing back to site of work, reconnecting electrical connection , recoupled and alinged with monoblock pumping set, testing for satisfaction running to the satisfactory of complete all as specified and directed by Engineer-in-Charge.. Note:-(i) Spare parts of monoblock pump set will be measured and paid seperately under relevant items of this schedule. (ii) T & P/vehicles for transportation of monoblock pump and motor will be arranged by the contractor and the cost deemed to be included in the quoted rate of this item (iii) While taking out pump for repairs , the contractor shall make arrangement for pluging suction and discharge line with dead flanges without extra cost, so that pumping of installation is not disturbed and there is no leakage of water
Material & labour for repairing of mono block pump of capacity 5 HP by dismantlling its pump and motor, taking out burnt copper winding of stator, cleaning the casing stator with wire brush,rewinding the motor using new super enamelled copper wire of same guage and with equal number of turns bringing back to site of work, reconnecting electrical connection , recoupled and alinged with monoblock pumping set, testing for satisfaction running to the satisfactory of complete all as specified and directed by Engineer-in-Charge.. Note:-(i) Spare parts of monoblock pump set will be measured and paid seperately under relevant items of this schedule. (ii) T & P/vehicles for transportation of monoblock pump and motor will be arranged by the contractor and the cost deemed to be included in the quoted rate of this item (iii) While taking out pump for repairs , the contractor shall make arrangement for pluging suction and discharge line with dead flanges without extra cost, so that pumping of installation is not disturbed and there is no leakage of water
Supply only SS impeller of suitable size for monoblock pump sets following capacity complete all as specified and directed by Engineer-in-Charge.
12.5 HP Capacity
10 HP Capacity
7.5 HP Capacity
05 HP Capacity
Supply only gland pressure plate including gland of suitable size for monoblock pump sets following capacity complete all as specified and directed by Engineer-in-Charge.
12.5 HP Capacity
10 HP Capacity
7.5 HP Capacity
05 HP Capacity
Supply only SS shaft sleeve of suitable size for monoblock pump sets following capacity complete all as specified and directed by Engineer-in-Charge.
12.5 HP Capacity
10 HP Capacity
7.5 HP Capacity
05 HP Capacity
Supply only mechanical seal of suitable size for monoblock pump sets following capacity complete all as specified and directed by Engineer-in-Charge.
12.5 HP Capacity
10 HP Capacity
7.5 HP Capacity
05 HP Capacity
Supply only SS stud of suitable size for monoblock pump sets following capacity complete all as specified and directed by Engineer-in-Charge.
12.5 HP Capacity
10 HP Capacity
7.5 HP Capacity
05 HP Capacity
Supply only bearing of suitable size for monoblock pump sets following capacity complete all as specified and directed by Engineer-in-Charge.
12.5 HP Capacity
10 HP Capacity
7.5 HP Capacity
05 HP Capacity
Supply only terminal plate of suitable size for monoblock pump sets following capacity complete all as specified and directed by Engineer-in-Charge.
12.5 HP Capacity
10 HP Capacity
7.5 HP Capacity
05 HP Capacity
Material & labour for remetalling turning & polishing of motor shaft including any lathe work required of centrifugal/monoblock pump sets of capacity 05 to 12.5 HP complete all as specified and directed by Engineer-in-Charge.
Material & labour for remetalling turning & polishing of motor shaft including any lathe work required of centrifugal/monoblock pump sets of capacity 15 to 30 HP complete all as specified and directed by Engineer-in-Charge.
Material & labour for remetalling turning & polishing of motor shaft including any lathe work required of centrifugal/monoblock pump sets of capacity 40 to 60 HP complete all as specified and directed by Engineer-in-Charge.
Disconnecting of electrical connection from panel board and opening the monoblock single phase motor upto capacity 2 HP and taking out the burnt winding wire cleaning the slots, rewinding the monoblock motor with super enamalled copper winding wire of existing gauge, weight etc including all spare parts like impeller,oil seal bearing etc and back re-installed after repair including testing and other insulating material complete all as specified and directed by Engineer-in-Charge.
Material & labour for spider star rubber coupling for centrifugal pump set suitable for 20/30 Hp pump set as per existing pattern complete all as specified and directed by Engineer-in-Charge.
Material & labour for spider star rubber coupling for centrifugal pump set suitable for 40 to 60 Hp pump set as per existing pattern complete all as specified and directed by Engineer-in-Charge.
Supply & fix in replacement of good quality tyre rubber coupling complete set inclding nut bolt and lathe machine work suitable for 15/20 Hp pump set as per existing pattern complete all as specified and directed by Engineer-in-Charge.
Supply & fix in replacement of good quality tyre rubber coupling complete set inclding nut bolt and lathe machine work suitable for 30/40 Hp pump set as per existing pattern complete all as specified and directed by Engineer-in-Charge.
Supply & fix in replacement of good quality tyre rubber coupling complete set inclding nut bolt and lathe machine work suitable for 50/60 Hp pump set as per existing pattern complete all as specified and directed by Engineer-in-Charge.
Supply & fix in replacement of good quality Tyre rubber coupling including nut bolt wahser complete suitable for 15/20 HP pump set as per existing pattern complete all as specified and directed by Engineer-in-Charge.
Supply & fix in replacement of good quality Tyre rubber coupling including nut bolt wahser complete suitable for 30/40 HP pump set as per existing pattern complete all as specified and directed by Engineer-in-Charge.
Supply & fix in replacement of good quality Tyre rubber coupling including nut bolt wahser complete suitable for 50/60 HP pump set as per existing pattern complete all as specified and directed by Engineer-in-Charge.
Supply & fix in replacement the following spares for oil immerssed star delta starter of existing make, with auto transformer of capacity upto 60 HP complete all as specified and directed by Engineer-in-Charge.
Relay
Timer
Moving contact set
Fixed contact set
Replacement of internal wiring
Transformer oil.
Labour only for detecting the fault on LT panel/ submersible pump set /pressure pumps sets/any type Of sarter etc, rectifying the defect on relays, metering devices, tightening the electrical accessories with required insulation materials, measuring and recording values of voltage, ampere, earth resistance, checking of motor and pumps for its correct functioning etc based on day to day complaints complete all as specified and directed by Engineer-in-Charge. (Spare parts required for the same will be measured and paid separately under relevant item)
Supply & fix in replacement 3 pole power contactor ML-4 AC3 rating 70 A, 415 V complete all as specified and directed by Engineer-in-Charge.
Supply & fix in replacement 3 pole power contactor ML-4 AC3 rating 40 A, 415 V complete all as specified and directed by Engineer-in-Charge.
Supply & fix in replacement 3 pole power contactor ML-4 AC3 rating 32 A, 415 V complete all as specified and directed by Engineer-in-Charge.
Supply & fix in replacement contactor 415V, AC, 50Hz, 3 phase, current rating AC-3 70-80 A with one pair of auxilary contacts (01NO+01NC) complete all as specified and directed by Engineer-in-Charge.
Supply & fix in replacement contactor 415V, AC, 50Hz, 3 phase, current rating AC-3 45-50 A with one pair of auxilary contacts (01NO+01NC) complete all as specified and directed by Engineer-in-Charge.
Supply & fix in replacement contactor 415V, AC, 50Hz, 3 Phase, current rating AC-3 25-30 A with one pair of auxilary contacts (01NO+01NC) complete all as specified and directed by Engineer-in-Charge.
Supply & fix in replacement contactor 415V, AC, 50Hz, 3 Phase, current rating AC-3 18-20 A with one pair of auxilary contacts (01NO+01NC) complete all as specified and directed by Engineer-in-Charge.
Supply & fix in replacement contactor 415V, AC, 50Hz, 3 Phase, current rating AC-3 9-12 A with one pair of auxilary contacts (01NO+01NC) complete all as specified and directed by Engineer-in-Charge.
Taking out carefully after disconnecting electrical connections and delivery line of open well submersible motor from UG sump/well/UG building any capacity of any make and type ,seperating pump and motor for repair purpose and re-assembling pump and motor after repairs, jointing of submersible cable, reconnecting delivery line to water mains, testing for satisfactory running and continuous flow of water complete all as specified and directed by Engineer-in-Charge. Note:- (i) Spare parts like impeller, GM Bush,thrust plate,thrust bearing and other material to make them servicable shall be included in the quoted rate. (ii) The rewinding of open submersible pump will be measured and paid seperately under relevant items of this schedule. (iii) T & P/vehicles for transportation of open well submersible pump set will be arranged by the contractor and the cost deemed to be included in the quoted rate of this item
Material & labour for taking out burnt copper winding of stator, cleaning the casing stator with wire brush, repair to rotor by turning , polishing and turning, rewinding of open well submersible electric motor AC 3 Phase 440 Volts of any make & any type with new PVC coated super enameled copper wire of same existing gauge including insulation material and cable jointing and testing at site complete for the following 02 HP capacity of motor complete all as specified and directed by Engineer-in-Charge.
Material & labour for taking out burnt copper winding of stator, cleaning the casing stator with wire brush, repair to rotor by turning , polishing and turning, rewinding of open well submersible electric motor AC 3 Phase 440 Volts of any make & any type with new PVC coated super enameled copper wire of same existing gauge including insulation material and cable jointing and testing at site complete for the following 05 HP capacity of motor complete all as specified and directed by Engineer-in-Charge.
Material & labour for taking out burnt copper winding of stator, cleaning the casing stator with wire brush, repair to rotor by turning , polishing and turning, rewinding of open well submersible electric motor AC 3 Phase 440 Volts of any make & any type with new PVC coated super enameled copper wire of same existing gauge including insulation material and cable jointing and testing at site complete for the following 7.5 HP capacity of motor complete all as specified and directed by Engineer-in-Charge.
Material & labour for taking out burnt copper winding of stator, cleaning the casing stator with wire brush, repair to rotor by turning , polishing and turning, rewinding of open well submersible electric motor AC 3 Phase 440 Volts of any make & any type with new PVC coated super enameled copper wire of same existing gauge including insulation material and cable jointing and testing at site complete for the following 10 HP capacity of motor complete all as specified and directed by Engineer-in-Charge.
Supply & fix in replacement MCCB's,415 Volts ,4 pole with fix / adjustable type having following capacities complete all as specified and directed by Engineer-in-Charge:-
MCCB 4 Pole, 415 V, fixed type, 125 Amps with breaking capacity 16 KA
MCCB 4 Pole, 415 V, Fix type, 160 Amps with breaking capacity 16 KA
MCCB 4 Pole, 415 V, Adjustable type, 250 Amps with breaking capacity 25 KA
MCCB 4 Pole, 415 V, Adjustable type, 400 Amps with breaking capacity 36 KA
Supply & fix in relacement of following sizes DOL starter in sheet metal enclosure complete all as specified and directed by Engineer-in-Charge:-
230 volts 50 Hz single phase for electric motor of capacity upto 2 HP
415 volts 50 Hz three phase for electric motor of capacity 5 HP
415 volts 50 Hz Three phase for electric motor of capacity 7.5 HP
Supply & fix in replacement over load relay suitable for 10 to 60 HP motor starter, 3 phase, 415 V AC, 50 HZ complete all as specified and directed by Engineer-in-Charge.
Supply & fix in replacement of Single Phase Preventer relay (SPP) Suitable for 10 to 60 HP motor including taking out old unserviceable preventer complete all as specified and directed by Engineer-in-Charge.
Supply & fix in replacement satr delta timer Suitable for 10 to 60 HP starter including taking out old unserviceable star delta timer complete all as specified and directed by Engineer-in-Charge.
Supply & fixing for digital type ammeter suitable for 10 HP to 60 HP pumpset panel ,flush type with appropriate CTs, AC, 50Hz in existing panel boards after disconnecting of cables and testing including removing unserviceable item complete all as specified and directed by Engineer-in-Charge.
Supply & fixing for digital type voltmeter 0-500 volts range, flush type, AC, 50Hz in existing panel boards after disconnecting of cables and testing including removing of unserviceable voltmeter complete all as specified and directed by Engineer-in-Charge.
Supply & fix LED phase indicating lamp R-Y-B colour as required at site complete with base holder suitable for AC, 240 volts and testing including removing of old unserviceable lamps complete all as specified and directed by Engineer-in-Charge.
Supply & fix mild steel framed works as joinst, channels angle or tee sections, fixed independently without connecting plates conforming to FE 410-W (Gde E-250) applying two coats of synthetic enamel paint over and including a coat coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.
Demolition of cement concrete (un-reinforced) in any description and in any position not otherwise specifically provided for complete all as specified and directed by Engineer-in-Charge.
Material & labour for PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in filling and mass concrete for foundation of header including dismantling complete all as specified and directed by Engineer-in-Charge.
Taking out carefully, after disconnecting electrical connections, complete assembly of non clog dry motor submersible pump set of capacity 30 HP, 3 phase, type KDA from sewage tank (about 7m deep),transporting the complete assembly to work shop, opening unserviceable parts, and carrying out repairs/replacement mentioned in the items here-in-below including replacement of oil,Reconnecting all the parts and transporting back to the site of work, reconnecting with electrical connections, installing testing & re-commissioning of the complete assembly complete all as specified and directed by Engineer-in-Charge. Note:-Spare parts of non clog submersible pump set will be measured and paid seperately under relevant items of this schedule.
Material & labour for rewinding, taking out old unserviceable burnt winding of non clog dry motor submersible pump set 30 HP and rewinding the same with super enamelled copper wire of same guage/size to get the same output of motor with and including material such as varnish, sleeves, etc and refixing the same in position with proper alignment, balancing and testing complete all as specified and directed by Engineer-in-Charge.
Supply only mechanical seal complete all as specified and directed by Engineer-in-Charge.
Supply only ball bearing complete all as specified and directed by Engineer-in-Charge.
Supply only 'O' ring set for non-clog submersible motor complete all as specified and directed by Engineer-in-Charge.
Supply only impeller suitable for non clog submersible motor complete all as specified and directed by Engineer-in-Charge.
Supply only oil suitable for dry non clog submersible motor complete all as specified and directed by Engineer-in-Charge.
Material & labour for cleaning of water filteration plant of capacity 125 Cum/Hr at AF Stn Bhuj area throughly with wire brush & bleaching powder and application of two coats of white wash on walls complete all as specified and directed by Engineer-in-Charge. The filtration plant shall comprise of the following:- (a) Floc module chamber - 02 Nos (b) Tube settler - 02 Nos (c) Sand bed filter (d) Water channel (Note:- Cleaning of water filter treatment shall be carried out every months and date of cleaning should be written in white letters on black background as directed by EIC)
Supply & fix in replacement membrane module 8" for RO plant complete all as specified and directed by Engineer-in-Charge.
Taking down carefully after disconnecting electrical connections and delivery line of vertical multistage high pressure pump of capacity 5/5.5 HP ,3 phase seperating motor and pump for repair purpose and taking out burnt winding of high pressre pump motor and rewinding the stator coil with super enamelled copper wire of same guage and with equal number of turns including insulating material and reassembling and refixing the motor and pump with true alignment, testing and commissioning complete all as specified and directed by Engineer-in-Charge. Note:- (i)Spare parts of vertical multistage high pressure pump will be measured and paid seperately under relevant items of this schedule. (ii) T & P/vehicles for transportation of open well submersible pump set will be arranged by the contractor and the cost deemed to be included in the quoted rate of this item
Taking down carefully after disconnecting electrical connections and delivery line of vertical multistage high pressure pump of capacity 03 HP ,3 phase seperating motor and pump for repair purpose and taking out burnt winding of high pressre pump motor and rewinding the stator coil with super enamelled copper wire of same guage and with equal number of turns including insulating material and reassembling and refixing the motor and pump with true alignment, testing and commissioning complete all as specified and directed by Engineer-in-Charge. Note:- (i)Spare parts of vertical multistage high pressure pump will be measured and paid seperately under relevant items of this schedule. (ii) T & P/vehicles for transportation of open well submersible pump set will be arranged by the contractor and the cost deemed to be included in the quoted rate of this item
Supply only SS impeller D type suitable for vertical multistage high pressure pump complete all as specified and directed by Engineer-in-Charge:-
5/5.5 HP capacity
03 HP capacity
Supply only SS plain diffuser suitable for vertical multistage high pressure pump complete all as specified and directed by Engineer-in-Charge:-
5/5.5 HP capacity
03 HP capacity
Supply only SS shaft suitable for vertical multistage high pressure pump complete all as specified and directed by Engineer-in-Charge:-
5/5.5 HP capacity
03 HP capacity
Supply only SS Bush/Spacer suitable for vertical multistage high pressure pump complete all as specified and directed by Engineer-in-Charge:-
5/5.5 HP capacity
03 HP capacity
Supply only bottom chamber suitable for vertical multistage high pressure pump complete all as specified and directed by Engineer-in-Charge:-
5/5.5 HP capacity
03 HP capacity
Supply only SS top diffuser suitable for vertical multistage high pressure pump complete all as specified and directed by Engineer-in-Charge:-
5/5.5 HP capacity
03 HP capacity
Supply only Copper Sulphate suitable for swimming pool complete all as specified and directed by Engineer-in-Charge.
Supply only TCCA-90 trichloroisocyanurie acid chlorination granules as oxidizing agent for swimming pool in white granular form of super quality contains chlorine 90 % duly packed in 45/50 Kg drum complete all as specified and directed by Engineer-in-Charge. Note:- (i)The TCCA- 90 chemical shall be supplied in manufacturers original packing duly marked with the date of manufacturing and expiry.
Supply & fix in replacement including lowering of virgin quality polypropelene rope 28 mm dia ISI marked, heavy duty grade complete all as specified and directed by Engineer-in-Charge.
Supply & fix in replacement of suction sweeper foot valve as per exisiting pattern and size of 50 mm including hex nipple of same size complete all as specified and directed by Engineer-in-Charge.
Supply & fix in replacement wooden/PVC brush suitable for suction sweeper complete all as specified and directed by Engineer-in-Charge.
Material & labour for servicing of air compressor including replacing air filters, cartridge (as per sample) pouring of oil complete all as specified and directed by Engineer-in-Charge. Note : Rate of any items are required to change/replace such as saftey valve,check valve,drain valve ,nut bolt,pressure pipe while servicing is also deemed to be included in quoted rate
Testing of water sample collected from 27 Wing / mundra road RO plant & supply water for chemical characteristics from approved government laboratories as laid down in the latest edition of manual on water supply and treatment published by the Govt. of India, Ministry of Works and housing and as specified in IS and complete all as specified and directed by Engineer-in-Charge and submission of report there of.
Testing of water sample collected from 27 Wing/ Mundra road RO Plant & supply water for bacteriological characteristics from approved government laboratories as laid down in the latest edition of manual on water supply and treatment published by the Govt. of India, Ministry of Owrks and housing and as specified in IS and complete all as specified and directed by Engineer-in-Charge and submission of report thereof.
Supply only calcium hypochlorite for water treatment following generic specification and specification complete all as specified and directed by Engineer-in-Charge:- Generic Specifications:- (a)Common name:- Stable Bleaching Powder/ High strength Bleaching Powder (b)Description/Apperance:-Dry free flowing and free from lupms (c)Toxic & Undesirable Substance :-Should not induce substance beyond accepeted limit as given in IS 10500(2012) in treated and disinfected. (d)Packing:- 20-25 Kg bags/40-45 kg Durms.Packing in drums is preferable to reduce fire hazard in places of high ambient temperature. Specification:- (a) Available Chlorine - 65 % (b) Stability-1/15Max (c) Particle size(passing through 1.70mm IS sieve-99.5 % (d) water insoluble matter-6% Max (e) Calcium Hydroxide-4% Max (f) Sodium Chloride -15 % Max Note: Test Certificate each batch of chlorine to be submitted at the time of delivery.
Supply & fix in replacement OFF load change over switch of capacity 200 Amp, 4 pole, on load application on sheet steel enclosure duly phosphatised and powder painted, termination suitable for aluminium cables, door interlocking facility complete all as specified and directed by Engineer-in-Charge.
Supply & fix in replacement OFF load change over switch of capacity 100 Amp, 4 pole, on load application on sheet steel enclosure duly phosphatised and powder painted, termination suitable for aluminium cables, door interlocking facility complete all as specified and directed by Engineer-in-Charge.
Material & labour for earthing complete with galvanised steel earth plate electrode 60cmx60cm x 6 mm thick buried directly in ground vertically to depth not less than 2.25 mtr below ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level connected to and including GI strip 32x6 mm as earth lead up to 7.5 mtr length by means of bolts, nuts check muts and washers etc. of galvanised iron or steel all as shown in electrical plate No. 3 including provn of GI protection pipe light grade of 32mm bore upto 7.5m length and connected earth strip to earthing test point all as shown in electrical plate No. 3 of SSR Part - I 2009 and as specified or indicated and testing on completion including necessary excavation & earthwork in any type of soil, PCC (1:3:6) type C1 chamber, precast slab 50mm thick in cement concrete (1:2:4)type B1 (rein forced with welded steel wire fabric (XPM) of weight not less than 4kg/sqm) with frame, funnel with watering pipe of 20mm bore medium grade, wire mesh and lugs test point etc complete all as specified and directed by Engineer-in-Charge.
Material & labour for mild steel plates,plain or chequered,5 mm thick or over in thickness in available sizes, Fe410-W(Gde-E-250) quality-A ,including applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed by Engineer-in-Charge. Note:- The rate included the cost of removal of old chequred plate. .
Supply & fix in replacement PVC insulated, sheathed, copper cable 3 core 4 sqmm complete all as specified and directed by Engineer-in-Charge.
Supply & fix in replacement PVC insulated, sheathed, copper cable 3 core 2.5 sqmm complete all as specified and directed by Engineer-in-Charge.
Supply & fix in replacement of LED aviation obstruction light with die cast aluminium housing with red polycarbonate dome single emitter type on over head tank of 18 to 21 mtr staging including fixing arrangement complete all as specified and directed by Engineer-in-Charge.
Supply & fix in replacement of pressure guage as per existing size suitable for centrifugal pump complete all as specified and directed by Engineer-in-Charge.
Supply & fix in replacement of heavy duty MS suction pipe in any capacity of UG Sump for centrifugal motor any capacity of 150 mm dia ,3 m long flanged welded on both side including nut bolt washer and rubber packing of suitable size complete all as specified and directed by Engineer-in-Charge.
Supply & fix in replacement of heavy duty MS suction pipe in any capacity of UG Sump for centrifugal motor any capacity of 100 mm dia ,3 m long flanged welded on both side including nut bolt washer and rubber packing of suitable size complete all as specified and directed by Engineer-in-Charge.
Supply, install, testing and commissioning including replacement of centrifugal pump set with horizontal axially split casing two stage single suction pump with horizontal shaft ,enclosed type balanced impellers,high tensile steel shaft,Deep grove ball/roller bearing of discharge capacity 198 Cum/Hr at 42 mtr head, 1450 RPM ,CI body, ,suction pipe size of dia150mm and outlet dia 100mm complete all as specified and directed by Engineer-in-Charge.
Material & labour for replacement of long radius MS bend heavy duty with suitable size flange,nuts ,bolts,washer,rubber gasket kit ,jointing,with existing pipe line/ motor pump including welding work complete all as specified and directed by Engineer-in-Charge:-
80 mm bore
100 mm bore
150 mm bore
Supply & fix in replacement of CI foot valve ISI marked with flanged ends including MS bolts, nuts and washers from UG Sump of any capacity complete all as specified and directed by Engineer-in-Charge:-
80 mm bore
100 mm bore
150 mm bore
200 mm bore
Supply & fix in repalacement of Non Return Valve class PN 1.0 of undermentioned type and size with cast iron body and both ends flanged,IS-5312 marked complete with neoprene rubber gasket,jointing material and incl nuts/bolts/washer of suitable size etc complete all as specified and directed by Engineer-in-Charge:-
80 mm bore
100 mm bore
150 mm bore
SSupply & fix in replacement of old unservicable gland packing with new to the sluice valve/centrifugal pump set of any size/capacity complete with and including MS nuts/bolts/washer of suitable size etc complete all as specified and directed by Engineer-in-Charge.
Supply & fix in replacement of cast iron sluice valves with flanged ends, class I PN 1.0, heavy duty, ISI marked, drilled type, non raising type, IS-14846 mark, including iron wheel, stainless steel spindle, complete with suitable rubber insertion 3mm thick at both ends with and including nuts, bolts and washers, fixed with and including suitable joints; fixing & jointing connected fittings like tapers,etc. including suitable jointing material following size of pipes complete all as specified and directed by Engineer-in-Charge:-
80 mm bore
100 mm bore
150 mm bore
Supply, install, connecting, testing and commissioning of fully automatic star-Delta motor controller suitable for centrifugal pump sets of capacity up to 40 HP in sheet-steel enclosure, 415 volt, 3 phase, 50 Hz,relay max range 50-80 Amp including Auto ON, indications of supply ON/OFF and pump ON/OFF, recording of real time voltage and current of pump with digital meter, single phase protection relay, phase reversal protection, phase unbalance protection etc complete including taking out existing old centrifugal motor controller from its location by disconnecting all cable connections complete all as specified and directed by Engineer-in-Charge.
Supply, install, connecting, testing and commissioning of fully automatic star-Delta motor controller suitable for centrifugal pump sets of capacity 15 HP in sheet-steel enclosure, 415 volt, 3 phase, 50 Hz ,relay max range 20-30 Amp including Auto ON, indications of supply ON/OFF and pump ON/OFF, recording of real time voltage and current of pump with digital meter, single phase protection relay, phase reversal protection, phase unbalance protection etc complete including taking out existing old centrifugal motor controller from its location by disconnecting all cable connections complete all as specified and directed by Engineer-in-Charge.
M/s Bombay Novelty Stores (BID ID -3329314)
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .