Supply, Installation Erection, testing and Commissioning of Electrical Equipment for Gate Electrification works at Ch.276.857 km of Kachchh Branch Canal

BILL OF QUANTITIES

(A) Percentage Rate Tender (Up to INR 50 Cr.)

Item Description Uom Total Amount

Item Description Uom Total Amount

No. Qty. (without

Supply and installation of powder coated junction box

outdoor type in two compartments made from 2/3 mm

thick M.S.Sheet . The junction box provided with 4 Nos

32 A MCB FP (C & S/ Siemens/ L&T make) & 1 nos

63A 4 pole MCB (C & S/ Siemens/ L&Tmake) complete

with internal wiring 4 sq.mm copper wire & CSTSN

1 Stud type terminal block (Polymide) suitable lugs. All No. 1 11699.042

necessary Accessories including the item. The box shall

be provided with front door hinged at one end and locking

at other end and having bakelite sheet cover inside for

M.C.B. Junction box size to be provided as

per site requirement and mounted on wall or flour with

Rate of supply of Gate Control Panel for 5 HP, 960 RPM,

415 V Induction Motor

Rate for Supply of Local control board for remote

operation of gate from gate structure

Rate for Installation/Erection /Commissioning and testing

of Gate control panel & local control board.

Providing and erecting armoured 12 core x 2.5 s.mm

copper cable multistrand copper conductor for 1.1 KV to

be laid on wall with necessary clamps or in existing

trench/pipe as per site requirement

(Polycab/Universal/Finolex/RR/ OR ISO make

Providing and erecting armoured 3 core x 6 s.mm copper

cable multistrand copper conductor for 1.1 KV to be laid

6 on wall with necessary clamps or in existing trench/pipe Mtr. 200 392.00

as per site requirement (Polycab/Universal/Finolex/RR/

OR ISO make equivelemt) )

Providing and erecting armoured 4 core x 6 s.mm copper

cable multistrand copper conductor for 1.1 KV to be laid

7 on wall with necessary clamps or in existing trench/pipe Mtr. 25 505.00

as per site requirement (Polycab/Universal/Finolex/RR/

OR ISO make equivelemt) )

Providing and erecting armoured 4 core x 2.5 s.mm

copper cable multistrand copper conductor for 1.1 KV to

be laid on wall with necessary clamps or in existing

trench/pipe as per site requirement

(Polycab/Universal/Finolex/RR/ OR ISO make

Contractor Engineer in charge

Point wiring for Light/ Fan primary point with 2 - 1.5 sq.

mm & earth wire of 1.5 sq. mm (Green) both are of ISI

marked 1.1 kv grade FRLS PVC insulated multistrand

copper wires, in with medium class Rigid PVC pipe and

accessories to be erected concealed in/ flushed on wall/

ceiling, complete with 6 A Tissino type ISI marked flush

9 type switch and accessories erected on metal/ PVC box 10 351.00

covered with 3 mm thick PC with medium class rigid

PVC pipe and accessories (Polycarbonate)/ Acrylic sheet

with necessary Lamp holder /Ceiling rose/ H.D connector

as directed/ instructed by Engineer / Site- in -Charge

and as per actual site requirement. (Make :Finolex/

Havells/RR/ Anchor/Hi-Fi)

Point wiring for loopd plug with 16 A Tissino type single

pole ISI mark switch and socket erected with necessary

10 connection erected on wooedn/metal/PVC block covered 10 162.00

with 3 mm thick PC/acrylic sheet for open/conceled

Mains with 1.1 KV grade FRLS PVC insulated ISI

marked stranded copper conductor wire of 2 wire 2.5 sq.

mm with medium class rigid PVC pipe and accessories to

be erected concealed in/ flushed on wall/ceiling, with

sq. mm copper conductor FRLS PVC insulated stranded

wire of green color for earth continuity with medium

class rigid PVC pipe and accessories. (Make :Finolex/

Havells/RR/Anchor)

Supplying and erecting 22-24 watts,surge-2KV,IP-20,4

feet LED indoor fittings with LEDs of wattage 0.2 Watt

to 0.5 Watt assembled on single MCPCB, with housing

used as a heat sink shall be made of thick sheet Steel

conforming to IS: 513/CRCA powder coated and high

U.V. & corrosion resistance with diffuser and/or

Polycarbonate optics with company mark/name 120 to

300 V, Power Factor more than 0.9, THD < 10 %,CCT

4000 K to 6500K, Uniformity ratio

>0.7,Luminaireefficacy> 100 lumens/watt ,LED driver

efficiency > 85 % CREE / OSRAM / PHILIPS Lumileds /

NICHIA / SEOUL/Bridgelux(U.S.A.) make LED used for

luminaire. ( fitting required LM-79 & LM-80

Certificates.(Cat-III)

Providing & erecting Approved make Power Saving

Watt Ceiling Fan with double ball bearing ISI mark with

13 Condenser 230 volt A.C. 50 Hz 1200 mm sweep No. 2 1929.00

complete having 3blades with aluminium blades with

canopy & 30 cms. down rod erected with earthing.

Supplying & Erecting Galvanized iron pipe post "B"

Class 88.9 mm OD, 4 mtr long duly painted with two

14 coats of aluminuim paint complete with metalic base plate No 3 3194.00

of 300x300x4 mm thickness for using as a compound

light pole with approx weight 32 Kg.

Supplying 50 mm dia.G.I . Pipe & erecting as directed

by Engineer-in-charge.

Supplying & Erecting approved make SMC press

mouldede composite FRP loop in , loop out approx 2mm

thick box complete with bakelite connector strip 4 way &

16 hinged doors having locking arrangements with mounting No 3 510.00

clamp with nuts, bolts & washer suitable for erection on

pole with cable clamps & earth bolt including copper

lugs. Size of box -250 mm x 200 mm x 100 mm (Deep).

Contractor Engineer in charge

Providing M 150/1:2:4 cement concrete foundation &

70% PCC from bottom including excavation for the pole

17 of size 45x45x100 cms Deep in below gound level with No 1 801.00

plinth of 45x45x cms higher upper ground level with

necessary curing and finishing in approved manner.

Providing street light pole Double Arm Bracket

comprising main B Class MS pipe of 4.2 cm/require

outside dia. complete with suitable B Class M.S. sleeve

tubing of approx. 45cms.length and suitable for

mm / 80mm. / require size pole top having sufficient

18 fastners for fixing the brackets and having spread of 1 No. 3 821.00

mtr. length with suitable rise as per site condition &

suitable welded stiffener reducer and nipple with

check nut complete painted with one coat of Red oxide

/ PU base primer and two coats of Aluminium / PU

Providing and erecting 240 v MCB double pole 6A to

32A switch for lighting Load (B Curve) having 10 KA

breaking capacity & confirms to IS : 8828 in existing

Supplying and erecting above 48 to 60 watts LED

street light fittings with High power White LEDs

wattage of 3 Watt and above assembled on single

MCPCB, efficiency more than 130 lm/w and corrosion

free High pressure die cast aluminum housing with

smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/

lenses .( Street light IP-65 surge protection 4KV

internal and light must have 440 v AC line supply with

over voltage protection ) ( OSRAM / PHILIPS

Lumileds / NICHIA / SEOUL/ BridgeLux (U.S.A.) /ISO

Make LED used for luminaire. [ CAT- III ]

Providing, Erection and connection charges for approved

make, ISI mark (L&T/ Havells/Siemens/ABB) 63 A

21 Triple Pole Metal clad Switch fuse unit 415/500 V with No. 1 3366.00

HRC fuse of suitable load and neutral link (Cat.III) on

new angle iron frame duly painted with red oxide.

Providing and erecting Approved make 63 Amp ELCBs /

RCCBs (cat-III) conforming to IS: 12640 and having

22 sensitivity of 30 mA and Short Circuit withstand capacity No. 1 3010.00

of 10 KA and suitable for operation on 3 phase and

neutral 415V,50Hz.

Work of Cleaning / Servicing / Maintenance / Repairing

23 of Motors, complete followed by inspection and testing No. 3 994.00

for raising and lowering of gates with effective braking .

Work of Cleaning / Servicing / Maintenance / Repairing

of E.M Brake assembly, complete followed by inspection

and testing for raising and lowering of gates with

effective braking.

Provding & erecting roler type limit switch with 1 no +

nc contact ,415 v. having aluminium housing with I.P.55

protection ( /L&T, BCH, siemens, or eqvivalent make

approved by Eng'r.in charge)

Contractor Engineer in charge

Supply of plate /sheet up to 20 mm thick (work as per site

requirement/instruction)

Supply of various size MS angle for gate parts & hoist

maintenance (work as per site requirement/instruction)

Fabrication work including labour,welding,gases,power

28 jigs & fixtures,machinery etc. for job of hoist plateform & MT 0.5 22653.62

Hoist mechanism parts.

Erection charges including labour,welding,gases,power

29 jigs & fixtures,machinery etc. for embeded & Hoist MT 0.5 11479.87

mechanism parts.

30 Rewinding of EM brake coil as per site requirement Set 3 2302.79

Supply and Ereting perforated G.I.cable tray size

200x50x2mm with all necessary accessories for fitting

like coupler S.S. Nut bolt, and cable tray cover with

fabricated GIMS Sheet having thickness 2 mm.

Providing & lying 300 mm Dia RCC Hum pipe for cable

to be laid 90 cms or required depth below ground in Hard

murmur/Tar road across the road crossing or on the floor

with necessary materials in an approved manner and

backfilling the depth of road and making surface as

normal ground level with cement mixtures materials.

Supplying & erecting funnel type earthing having C.I.

earth plate of 45 x 45 x 0.35 cms. burred in specifically

prepared earth pit 3 mtr. below ground with 40 kg.

charcoal and salt with alternate layers of charcoal & salt,

20mm.dia. G.I. pipe with Funnel with a wire mesh for

watering & bricks masonry block, C.I. Cover complete as

per para 7.3 of IS 3043 with necessary length of double

Galvanised Iron / copper earth wire No 6 SWG bolted

with lug to the plate and covered in 12 mm dia. G.I. pipe

2.5 mtr long complete connected to the nearest switch

gear with end socket as per direction & duly tested by

earth tester confirming to IS .

Providing and Erecting required size HOT deep

Galvanised iron strip/8 to 16 SWG/ wire for earthing .

Labour charges for making of Cable trench in Hard

Murrum / Tar Road of suitable width of 90 cm or required

35 depth for laying any size of cable or locating the fault all Mtr. 25 74.00

over the run and back filling the same and making the

surface as normal ground.

Supplying rubber matting of 4 mm thickness and of

36 required length and breadth with good insulation property 6 1017.00

Providing pair of rubber handgloves suitable for working

on 11 KV/22 KV supply.

Supplying standard first AID box with antiseptic

cream,medicine for use on wounds due burn,crepe

bandage,gauge bandage,medicated ready to use (Band-

aid) adhesive tape formed icinaluser ,Scissors, anti-septic

solution (Savlonor similar) etc.(All above contents shall

be of standard makes)

Contractor Engineer in charge

Supplying & erecting D.C.P. Type fire extinguisher of

Kg. capacity cartridge type with gun metal cap 150 gram

CO2 gas cartridge,powder and brackets confirming to ISO

and complete erected on wall .

Transportation charges including loading and unloading

of materials (to and from) to transport the panels,

cables,poles etc all the tender items to caary out the

subjected work of KBC at chainage 276.857 km.

Contractor Engineer in charge

I/We am/are willing to carry out the work at… ...................... % above/below percent (Should

be written in figures and words) of the estimated rate mentioned above. Amount of my /our

tender works out as under.

Estimated amount put to tender Estimated amount put to tender

De Add………% Above

In words In words

(B) For Item Rate Tender (For above INR 50 Cr.):

Item Description of Item Quantity Unit Rate Amount

No. (with brief specification

and reference to book of In In

specifications) figures Words

(A) Total Tendered Amount

(B) Rebate on above tendered amount (if any) % (in figure) ………………………………

(C)Net Tendered Amount (A-B) (in figure) ………………………………

1 The Contractor shall exhibit a board with detailed specification and details of work as

directed by the Engineer-In-Charge for which no extra payment shall be made.

2 The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3 GST and Income tax TDS will be deducted at a source while making payments of bills

4 In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per

Govt. G.R.: PRC-10/2017 Cement Consumption/16/C, Date:11/05/2017 as stated in

S.O.R. therefore in R.C.C. items where there is a change as per actual mix design the cost

of difference of cement consumption have been deducted from the rate of original item

at the rate of input rate mentioned in all the tender.

Contractor Engineer in charge