Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | 1₹20.7 LAccepted-AOC WANIAWAD BHUJ KUTCH 370001 | BHUJ | KUTCH | GUJARAT | 370001 | 1 | Accepted-AOC AOC | |
| 2 | 2₹22.8 L+₹1.6 L (7.71%)Rejected-AOC | 2 | Rejected-AOC NOT ACCEPTED |
Tender Value
₹20 L
EMD Value
₹40,000
Closing Date
22 Jul 2023, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE ARMY BHUJ
GE ARMY BHUJ
REPAIRS TO INTERNAL FITTING FIXTURES IN MD ACCN OF ORS QTRS ALONG WITH CERTAIN MISC WORKS UNDER AOR OF AGE B R II OF GE(ARMY) BHUJ AT MIL STN BHUJ
2023_MES_596307_2
8114
Open Tender
Civil Works
Item Rate
270 days
ARMY AREA BHUJ
REFER TENDER
6 documents required · 6 mandatory
₹500
GE ARMY BHUJ
₹40,000
Yes
14 Sept 2023
26 Jun 2023
24 Jul 2023
26 Jun 2023
22 Jul 2023
4 Jul 2023
Amount
M&L for special treatment of sunken portion of WCs and Bath room as per following stages: Stage 1 :- Demolition of WC including lime concrete and cement concrete coba etc and preparing the surfaces of existing sunken portion of WCs or bath etc with wire brush to remove all loose dirt, oil grease etc . Stage 2:- Providing 10mm thick plaster in CM 1:3 with chemical of Dr. Fixit Pidicrete URP or plaster seal of STP Ltd Stage 3:- Applying Dr Fixit Primseal primer or STP Ltd (and allow to dry for 8 hours) under touch dry condition Stage 4:- Applying two coats of water proofing decorative elastomeric coating system of Dr Fixit Raincoats with DFT 100 Micron or shalicry 215 of STP(The surface after painting one coats shall be allowed to dry of 6 hours before next coats) all as per manufacturer instruction Stage 5:- Making holes in wall and fixing 600mm long 40mm dia GI spout for draining the surplus water if any.
M&L Plain cement concrete 1:4:8 type D-2 as in mass filling in sunken portion.
Dismantling 100 mm cast iron /PVC SWR drain pipes, jointed in cement mortar and taking out of trenches, if required (incuding fitting & fixtures)
Ditto above but 75 mm dia pipe.
S&F in repair PVC (SWR) gully trap 110 mm, setting and jointing with solvent cement complete all as specified and directed.
S&F in repair 110 mm bore PVC (SWR) pipes Type B ISI marked single socketed in any length with rubber ring joints laid in tranches complete all as specified and directed.
S&F in repair 75 mm bore PVC (SWR) pipes Type B ISI marked single socketed in any length with rubber ring joints laid in tranches complete all as specified and directed
S&F in repair 110 mm bore PVC (SWR) pipes Type B ISI marked single socketed in any length with rubber ring joints laid on wall complete all as specified and directed
S&F in repair 75 mm bore PVC (SWR) pipes Type B ISI marked single socketed in any length with rubber ring joints laid on wall fixed complete all as specified and directed
S&F in repair PVC (SWR) bends, 110 mm bore, any radius complete all as specified and directed.
S&F in repair PVC (SWR) bends, 75 mm bore, any radius complete all as specified and directed.
S&F in repair PVC (SWR) bends, 110 mm bore, any radius with access door complete all as specified and directed.
S&F in repair PVC (SWR) bends, 75 mm bore, any radius with access door complete all as specified and directed.
S&F in repair PVC (SWR) Junction, single, (single T) equal or unequal, 110 mm bore, with access door complete all as specified and directed.
S&F in repair for PVC (SWR) vent cowl, 110 mm bore complete all as specified and directed.
S&F in repair PVC (SWR) 75mm branch piece, single (single Y) equal or unequal with access door complete all as specified and directed.
S&F in repair PVC (SWR) 75mm branch piece, double (double Y) equal or unequal with access door complete all as specified and directed.
S&F in repair PVC (SWR) 110mm branch piece, single (single Y) equal or unequal with access door complete all as specified and directed.
S&F in repair PVC (SWR) 110mm branch piece, double (double Y) equal or unequal with access door complete all as specified and directed.
S&F in repair vitreous china squatting pan, Orissa pattern, size 580 x 440 mm white with integral foot rests and connection with cast iron P trap and to flushing pipe, anti syphonage pipe etc (excluding flushing cistern and flush pipe) complete with provision of lime concrete bedding including taking down/ Dismantling existing unserviceable WC of any description and in any position & fixing new WC in repair and making good the disturbed surfaces to match with existing surfaces complete all as specified and directed.
S & F in repair vitreous china wash basin, white flat back , size 550mmx450mm with and including Waste fittings, brass, chromium plated for basins with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed with and including Supplying and fixing cast copper alloy chromium plated fancy type pillar tap 15mm bore, screwed down high pressure with or without lettered hot or cold with long shanks, screwed for iron pipe complete all as specified and directed.
S & F in repair vitreous china wash basin, white flat back , size 450mmx300mm with and including Waste fittings, brass, chromium plated for basins with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed with and including Supplying and fixing cast copper alloy chromium plated, fancy type, pillar tap, 15mm bore, screwed down high pressure with or without lettered hot or cold with long shanks, screwed for iron pipe complete all as specified and directed.
S&F in repair vitreous china urinal Flat Back Half Stall (HxWxP): 345X320X560 mm white with grating and union for discharge pipe (excluding flushing cistern, flush pipe and white pipe) and providing fixing of plugs bedding urinal against wall including taking down the old one complete all as specified and as directed. (Make : Prayag Cat No 4998 or equivalent of Cera / Parryware)
S&F in repair PVC valve-less, syphonic action type, flushing cistern, low level, 10 litre capacity (ISI marked) white with inlet, ball valve, float and handle including brackets complete all as specified and directed.
S&F Stop valves, cast copper alloy, ISI marked ,screwed down high pressure with crutch of butter fly handle, fancy type , chromium plated, with long shank and cup, screwed both ends for iron pipes or for union , for 15 mm bore , complete all as specified and directed.
Taking up or down existing unserviceable upvc/ mild steel water tubing and connections 15mm dia, any grade, of any description or in any position including fittings complete all as specified and directed
Taking up or down existing unserviceable upvc/ mild steel water tubing and connections 20mm dia, any grade, of any description or in any position including fittings complete all as specified and directed
Taking up or down existing unserviceable upvc/ mild steel water tubing and connections 25mm dia, any grade, of any description or in any position including fittings complete all as specified and directed
Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring, etc and making good, cutting not exc 10 cm girth
Supplying and Laying 16mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed
Supplying and Laying 20mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed
Supplying and Laying 25mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed
S&F bib tap, cast copper alloy chromium plated, screwed down high pressure with crutch of butter fly handle fancy type CP for 15 mm bore dia complete all as specified and directed.
S&F for Swivel shower rose size 125 mm of PTMT , any colour , for fixing with 15 mm dia pipe ,( minimum weight 40 gm. ) with and including Shower arm 15 mm size, 195 mm long with bend of 45 degree with flange of PTMT any colour (Min wt. 40gms) , fixed in repairs , complete all as specified and directed .
S&F PVC connections 15 mm size with PTMT nuts of length 450 mm
S/F in repair 75 mm bore PVC (SWR) floor trap plain with grating incl jointing with solvent cement
S&F in repair vitreous china Wash down water closet (pedestal pattern), complete including Pedestal pan and trap and seat cover, including connection to drain ( or outgoing pipe) and flushing pipe, antisyphonage pipes etc (excluding flushing cistern and flush pipe) complete
S&F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes ; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting unions to pipe, overall size 495mmX420mm bowl size 410mmX330mmX160mm.
S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes ; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting unions to pipe, overall size 915mmX460mm bowl size 410mmX330mmX160mm.
S&F in repair Rotational moulded polyethylene water storage tanks ISI Mark 1000 Litres Capacity ( Cylindrical vertical with closed top hoisted and fixed in position all as specified in SSR Part-I
Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar
M&L Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing laid over 20mm thick screed layer in cement mortar 1:6 and pointed in white cement with pigment to match with colour of tile complete all as specified.
M&L Granite (of any type) tiles 20mm thick machine cut, in skirting/dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete laid over 10mm thick screed layer in cement mortar 1:4
Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations
Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises all as directed
M&L Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles, over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6) complete all as specified and directed.
M&L for glazed ceramic tiles, coloured tiles, 450X300 x 7mm thick on vertical faces i.e.. as in skirting/dado etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles fix over and including 10 mm thick backing coat in cement mortar (1:4) complete all as specified and directed.
Taking down cement plaster of any description and in any position of brick or stone wall/concrete surfaces on walls ,ceiling etc including raking out joints ,hacking for key scrubbing down with water etc & prepared to receive new plaster complete all as specified and directed
M&L rendering 15 mm thick in CM 1:6 on brick/concrete wall surfaces of any description, and finishing the surfaces even and smooth without using extra cement complete all as specified and directed .
M&L for 15mm thick rendering on fair faces of brick/concrete surfaces in CM 1:4 finished even and smooth without using extra cement mixed with water proofing compound (Note :- WPC shall be measured & paid separately)
Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces with smart painting tools complete all as specified and directed.
M&L for Preparation of old surfaces by complete removal of existing treatment and applying two coats of oil bound distemper over one coat of primer on walls complete all as specified and directed
M&L for preparation of the newly plastered surfaces of walls & applying two coats distemper oil- emulsion , white or tinted over a coat of primer surfaces of wall complete all as specified and directed.
M&L for rendering 5 mm thick in Cement Mortar (1:3) on ceiling finished even and smooth without using extra cement complete all as specified and directed.
M&L for preparation of the newly plastered surfaces of ceiling & applying 3 coats of white wash on ceiling surfaces complete all as specified and directed.
Providing & applying Rising damp-proof coating system with Single component ready to use damp-proof coating Roff Hydamp : 1.SURFACE PREPARATION: Thoroughly brush and clean all laitance, loose particles such as dirt, grease, mortar droppings, release agents, efflorescence, bird droppings, etc. All large voids or hollow portions must be removed and re-plastered. Non- moving cracks having width upto 5 mm must be filled with Polymer based crack filler. 2 APPLICATION: Apply the first coat of Dr Fixit Dampguard Classic with a paintbrush directly on the prepared surfaces by mixing ( 1 part base:1 part hardner: 1 part of water) . Allow to dry for a minimum 2-3 hrs. Apply one part of DAMPGUARD mixed chemical and 2 parts of OPC white cement/Birla Putty and make the Putty, apply Putty on the entire surface area. Allow it to dry for at least 3-4 hours. Apply the Final coat of Dr Fixit Dampguard Classic on the entire surface and allow the surface to air cure 48 Hrs proceeds to paint.
S&F in repair Bib taps CP fancy type with butterfly handle screwed down high pressure for 15mm bore ISI marked complete all as specified and directed by Engineer in Charge
S&F in repair ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe 20mm bore (Minimum weight 210 gms) complete all as specified and directed by Engineer in Charge
S&F in repair Bib tap standard of PTMT any colour high pressure screwed for iron pipe 15mm bore (Minimum weight 90 gms) complete all as specified and directed by Engineer in Charge
S&F in repair Pillar taps cast copper alloy quarter turn, fancy type CP screwed down high pressure for 15mm bore complete all as specified and directed by Engineer in Charge
S&F in repair Stop valve of PTMT any colour high pressure screwed for iron pipe 15mm bore (Minimum weight 90gms) complete all as specified and directed by Engineer in Charge
S&F in repair stop valve of PTMT any colour high pressure screwed for iron pipe 20mm bore (Minimum weight 112gms) complete all as specified and directed by Engineer in Charge
S&F in repair stop/angle valve cast copper alloy screwed down high pressure with crutch or butterfly handle for pipe of 15mm/20mm bore complete all as specified and directed by Engineer in Charge
S&F waste coupling of PTMT (half or full threaded) for discharge pipe of 32mm bore (Minimum weight 45gms) complete all as specified and directed by Engineer in Charge
S&F PVC waste pipe for 32mm bore pipe complete complete all as specified and directed by Engineer in Charge
NOTE APPLICABLE FOR ALL ITEMS :- If rate quoted for similar/identical items in same part of Sch ‘A’ is at variance, the lowest rate quoted shall only be considered for payment to the contractor.
M/s Pal Builders
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .