REPAIR TO FLOOR ROOFING VALLEY GUTTER FALSE CEILING PLINTH FLOOR PLINTH PROTECTION AND MISC REPAIRS TO CERTAIN BUILDINGS IN TECH AREA AT AF STN BHUJ

Amount

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and as directed.

S&F mild steel work in tubular trusses/structures of square/round/ rectangular pipes, rafters, purlins including special shaped washer etc. complete using ERW or inductuin butt welded tubes confirming to IS-1161-1998 grade St-240 including notching, drilling, fitting, rivetting and or welding or connecting bolts and nuts, cleats, gusset plates etc complete all as specified and as directed.

S&F mild steel for wind ties for roof including securing bolts ,incuding cutting tops to shape as directed , drilling holes and similar works conforming to Fe-290 Gde E-165

M & L for preparation of new or previously un treated steel and iron surfaces over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide or zinc chrome on steel and iron surfaces all as specified and directed.

M & L for preparation of new or previously un treated steel and iron surfaces n.exc 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide or zinc chrome on steel and iron surfaces all as specified and directed.

Dismantling of plain or corrugated Abestos cement sheeting , any gauge , thickness roofing covering .

S&F Pre-painted galvalume aluminium zink coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof coverimg/ cladding to wall, fixed with self tapping screws as specified. Make JSW, TATA or equivalent

S & F coloured galvalume ridges,corner piece,barge board,window flashing etc, 0.50 mm thick, fixed with L or J type,special screw or crenked hook bolts in roofs , walls etc. Make JSW, TATA or equivalent

Demolition of concrete of any description in any position otherwise specifically provided for complete all as specified and directed.

M&L for 75mm thick cement concrete type C2 1:3:6 using 40mm graded aggregate as plinth protection finished even and smooth without using extra cement, laid in bays, joints filled with sand and bitumen mixture at 1:1 ratio complete all as directed

Taking down existing water proofing tretment on RCC slab / beams with bitumen felt with out damaging structure and removing the debrise outside the MD land and M&L for plaster 10 mm thck on concrete surfaces in cement mortar 1:3 finished even and smooth using WPC @ 3% by weight of cement and preparing the surfaces to recive WPT treatment , applying a coat of bitumenm primer confirm to IS - 3384-1986 @ 3% per sqm . providing APP modified memrane with non woven polyster reinforcement/mat ( centre core) by tourch application over primed surfaces all as specified and directed by Engr-In- Charge

Dismantling Wall and Ceiling Boards (Fibre, Pulp, Insulation etc.) or Insulation Board/Slab/Blankets of any thickness, etc. including cover fillets of any descrip-tion, complete all as specified and as directed.

M&L for providing 12mm thick Gyp boards in ceilings fixed to ceiling sections with screws @ 300mm centre to centre and making good joints Gypsum binder including preparing the surfaces of ceiling boards and applying 2 coats of acrylic oil emulsion distemper with GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre, intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from sofits at approxly 900mm centre to centre with GI cleats, GI suspenders and steel expansion fasteners with and including ceiling section of 0.55mm thick having kurled web of 50 mm and flange of 26 mm each side with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre all as specified as directed.

M&L for false ceiling corners with designed angular shape of size 100x100mm with POP fixed on 6mm thick fibre board with 20x20mm, 0.55mm thick galvanised sections fixed at intervals not more than 750mm complete al as specified and directed by Engr-in-Charge.

M&L in repairs forfalse ceiling of perforeted particle board/tiles 60X60 cm in size and 12mm thick fixed with nails to timber frame work or with staples on snap grid fixed with screws all as specified and directed.

M&L for anodised aluminium snap grid frame work for false ceiling all as specified and directed .

Supply and fixing Rotational moulded polythelene water storage tank, three layered, ISI marked, cylindrical vertical with closed top including dismantling existing water tank and removingto store of following capacity (Make - Sintex / Euro / Cera) : -

1000 litres capacity

750 litres capacity

500 litres capacity

M&L for 75 mm thick cement concrete type C-2 (1:3:6) using 40 mm graded stone aggregate as in sub base under interlocking tiles.

M&L 60 mm thick (M-35 mix) glossy rubber mould interlocking tiles (paver blocks red & yellow colour topping) conforming to IS-15658-2006 laid dry over 30 mm copacted sand bed, size & pattern of tiles all as directed by Engineer-in-Charge.

S&F PVC/PTMT shelf fixed to walls with screws including necessary drilling holes. Make : Prayag cat No 190-C or equivalent of polytuf / pearl.

S&F 6mm thick tinted glass as approved by GE, fixed to existing aluminium door/ windows including hacking out existing glass and provn of rubber beading.

Hacking out old broken glass (any thickness, size, quality or description) from wooden /steel frames or stone , concrete or brick surrounds, glazed with putty or fixed with beads.

S&F 4.00 mm thick sheet figured glass pin headed type and glazing with oil putty in square n exc 0.50 Sqm in each pane.

Taking down Chowkat or Frame (without taking off shutter from the frame) not exc. 1.50 Sqm Each, complete all as specified and as directed.

S&F PVC door PDS-01 comprising of shutter and frame of Make : Accura Polytech Pvt Ltd (Accucel) all as shown on drg No.CEAA/TD/149 sheet No. 1/1 (PVC RIGIDE FOAM) , door frame/ chowkhats of solid rigid foam profile FP-6030 and shutter of solid PVC foam profile FP 7114 with 4 mm thick high pressure compact laminate as infill (Panel) including necessary hardeware fittings all as specified and directed by EIC.

M&L for aluminium window with double side hung shutter for glazing and gauging and frame with one or more rebates made out of JINDAL/ INDAL anodised aluminium section including section for fixing of aluminium grills with suitable fixtures, jointing cleats for fixing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium beading screws, type B20 100mm long suitable handle and anodised aluminum fittings such as stay, hinges glazing with 5 mm thick tinted sheet glass and gauging with aluminium wire cloth of size 0.45mm dia of wire and 1.40mm aperture as per drg No. CEAA/TD/133 sheet No. 1/2 and 2/2 dated 13.12.02 except fixed glazing (FG) all as specified and directed.(Tint of glass shall be approved by GE) Note :- Aluminium grill fixed under above item shall be measured and paid separately

Supply only aluminium anodised grill of approved shape with opening in grill 66mm x 80mm (diagonally) or nearest to + 5mm made out of standard aluminium moulded section of size 6mm x 7mm

M&L for rendering 10mm thick on concrete surface in cement mortar 1:6 finished even & smooth without using extra cement.

M&L for preparation of new or previously untreated concrete or PCC block masonry external surfaces and applying two coats of exterior emulsion paint (in camouflage pattern as approved by the GE) over a coat of primer all as specified and directed by EIC using any one of following material :- Make Brand Nerolac Suraksha Asian ACE Berger Walmasta

M&L for preparing new plastered wall surfaces and applying two coats of distemper with distemper oil emulsion, white or tinted including one coat of Birla White Putty by finishing the surfaces even and smooth complete all as specified and directed by EIC.

Taking down cement plaster on brick or stone walls etc including raking out joints hacking for key scrubbing down with water etc.

Rendering 15mm thick in CM (1:4) on block masonry surfaces finished even and smooth without using extra cement.

M&L for PCC 1:3:6 type C2 as in foundation, filling , Bed Block and mass concrete.

Demolition of stone slabs any description or any thickness laid dry or laid dry and pointed in any mortar complete all as specified

M&L for 20mm thick Granite (Z Black) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like including 20mm thick screed bed of cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and as directed. NOTE : Cost of Screed Bed shall deemed to be included in QUOTED UNIT RATE.

M&L Granite (Z Black) tiles 12 to 15mm thick machine cut, in vertical surfaces such as riser, skirting, dado, etc. including rounding edges, nosing, pointing on nose, etc., over and including 12mm thick screed bed in cement morter 1:3 and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing, complete all as specified and as directed. NOTE : Cost of Screed Bed shall deemed to be included in QUOTED UNIT RATE.

M&L for 100mm thick cement concrete type B-1 1:2:4 ( 20mm graded aggregate ) finishing the surface even and smooth without using extra cement.all as directed by Engr-in charge

M&L for 100mm thick cement concrete type D2 1:4:8 using 40mm graded aggregate finished even and smooth without using extra cement.

Forming dummy joints 30 mm deep X 10 mm wide filled with sealing compound grade 'B'

M&L for 25mm thick cement concrete type B-1 1:2:4 ( 20mm graded aggregate ) finishing under floor, surface even and smooth without using extra cement.all as directed by Engr-in charge

M&L for Vitrified ceramic polished light shade tiles 10mm thick area of each tile exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed 15mm thick in CM-1:6 complete all as specified.

All as per Ser Item No 7 above but in vertical surfaces such as dado, skirtingand riser etc all as directed by the EIC.

Reparing /Taking down Alminium shutters of any description area exc 1.00 Sqm and not exc 2.00 repairing by retightening screws ,almn cleats and securing top & bottom rails using MS 10mm bar having both side threding incl bolting,fixing new rubber padding, Almn snap beading,glazing clips and refixing resuring in same opening complete all as specified and as directed by Engineer-in-Charge.

All as per item above here in before but area not exc 1.00 Sqm each.

Demolition Cement Concrete (un-reinforced) of any description (Roof Padding) and in any position not otherwise specifically provided for, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (12.5 mm graded aggre-gate) in Roof Padding, kerbs or mud stops, rounded or chamfered on edges complete all as specified and as directed by Engineer-in-Charge.

S& F 0.71 mm Plain, Aluminium sheeting, Alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing (length and girth as fixed) complete all as specified and directed.

M & L Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed

S&F Iin repair (Aluminium extructed section) Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed

S&F in repair, Gun Metal Globe or Gate Valve 20mm bore (dia) with Iron Wheel Head, screwed both Ends for Iron Pipe and fixed, complete all as specified and as directed.

S&F in repair, Ball Valve 20mm dia (minimum Weight 210 Gram), high pressure of PTMT with epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe and fixed, complete all as specified and as directed.

S&F in repair, Ball Valve 25mm dia (minimum Weight 210 Gram), high pressure of PTMT with epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe and fixed, complete all as specified and as directed.

BHAVANI PROVISION STORES

SHREE BHANU ENTERPRISE

Hi-Tech Systems

Ahmed B Khatri

M/s Bombay Novelty Stores