B.R.R. Vamsadhara Project Circle, Srikakulam

Earth work excavation for foundations and depositing on bank for all lifts and with an initial lead of 10m including all operational, incidental, labour charges such as shoring ,sheeting, planking, strutting, etc. complete for finished item of work including seigniorage excluding dewatering charges etc as per SS - 20 B (APSS 308).

Filling with useful available excavated earth (excluding rock) in trenches, sides of foundations and basement with initial lead in layers not exceeding 15 cm thick, consolidating each deposited layer by watering and ramming including cost and conveyance of water to work site and all operational, incidental, labour charges, hire charges of T & P etc., complete for finished item of work. (APSS NO. 309 & 310)

Filling with Sand in trenches, sides of foundations and basement with initial lead in layers not exceeding 15 cm thick, consolidating each deposited layer by watering and ramming including cost and conveyance of water to work site and all operational, incidental, labour charges, hire charges of T & P etc., complete for finished item of work. (APSS NO. 309 & 310)BLD-CSTN-2-8

Plain Cement Concrete corresponding to M10 grade as per IS 456 equivalent to (1:3:6) proportion nominal mix (cement: fine aggregate: Coarse aggregate) using 40mm size HBG (SS5) metal from approved quarry with concrete mixture including cost and conveyance of all materials like cement, sand(unscreened), coarse aggregate, water etc. to site, including seigniorage charges, sales & other taxes on all materials, all operational, incidental, and labour charges such as mixing, laying and ramming concrete in layers in position not exceeding 15cm, finishing top surface, curing concrete, etc., complete for finished item of work.(APSS No. 402).

Supply and placing of the Design MixConcrete M25 corresponding to IS 456 usingWEIGH BATCHER / MIXER with 20mm sizegraded machine crushed hard granite metal(coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand)coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including alloperational, incidental and labour charges such as weigh batching, machine mixing,laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No.402)with minimum cement content as per IScode from standard suppliers approved bythe department including pumping,centering, huttering, laying concrete,vibrating, curing etc. complete but excludingcost of steel and its fabrication charges for finished item of work. (For Footings)

Supply and placing of the Design MixConcrete M25 corresponding to IS 456 usingWEIGH BATCHER / MIXER with 20mm sizegraded machine crushed hard granite metal(coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand)coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including alloperational, incidental and labour charges such as weigh batching, machine mixing,laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No.402)with minimum cement content as per IScode from standard suppliers approved bythe department including pumping,centering, huttering, laying concrete,vibrating, curing etc. complete but excludingcost of steel and its fabrication charges for finished item of work.(for Plinth beams)

Supply and placing of the Design MixConcrete M25 corresponding to IS 456 usingWEIGH BATCHER / MIXER with 20mm sizegraded machine crushed hard granite metal(coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand)coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including alloperational, incidental and labour charges such as weigh batching, machine mixing,laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No.402)with minimum cement content as per IScode from standard suppliers approved bythe department including pumping,centering, huttering, laying concrete,vibrating, curing etc. complete but excludingcost of steel and its fabrication charges for finished item of work.(for Columns)

Supply and placing of the Design MixConcrete M25 corresponding to IS 456 usingWEIGH BATCHER / MIXER with 20mm sizegraded machine crushed hard granite metal(coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand)coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including alloperational, incidental and labour charges such as weigh batching, machine mixing,laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No.402)with minimum cement content as per IScode from standard suppliers approved bythe department including pumping,centering, huttering, laying concrete,vibrating, curing etc. complete but excludingcost of steel and its fabrication charges for finished item of work.(For Lintels)

Supply and placing of the Design MixConcrete M25 corresponding to IS 456 usingWEIGH BATCHER / MIXER with 20mm sizegraded machine crushed hard granite metal(coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand)coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including alloperational, incidental and labour charges such as weigh batching, machine mixing,laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No.402)with minimum cement content as per IScode from standard suppliers approved bythe department including pumping,centering, huttering, laying concrete,vibrating, curing etc. complete but excludingcost of steel and its fabrication charges for finished item of work.(For Slab 150mm thick)

Supply and placing of the Design MixConcrete M25 corresponding to IS 456 usingWEIGH BATCHER / MIXER with 20mm sizegraded machine crushed hard granite metal(coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand)coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including alloperational, incidental and labour charges such as weigh batching, machine mixing,laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No.402)with minimum cement content as per IScode from standard suppliers approved bythe department including pumping,centering, huttering, laying concrete,vibrating, curing etc. complete but excludingcost of steel and its fabrication charges for finished item of work.(For Roof level beams)

Supply and placing of the Design Mix Concrete M 25 grade corresponding to IS 456 with minimum cement content of 380 kgs per 1 cum of concrete and required quantity of Chemical Admixtures per 1 cum of concrete using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate) ( consisting of nominal size metal 60% of 20mm , 15% of 13.20/12.50mm , 15% of 10mm and 10% of 6mm ) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials , centering using Casurina Ballies , Bamboos , Wooden Reapers , Runners , Wood Posts , Wall Plates etc., for 60cm wide sun-shades 7.5cm thick at fixed end and 5cm thick at free end with an average thickness of 6.25cm including plastering to all exposed faces 12mm thick in two coats with base coat of 8mm thick in CM (1:5) and top coat of 4mm thick in CM (1:3) using screened sand in morta for plastering rwith dubara sponge finishing , including all operational, incidental and labour charges such as weigh batching, machine mixing, lifting of concrete manually, laying concrete, curing, overheads & contractors profit complete etc., but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402, 403 & 903) for sunshades:

Supplying, fitting and placing TMT (Fe-500) bar reinforcement in VRCC works complete as per drawings and technical specifications for Bars below 36 mm dia including over laps and wastage, where they are not welded

Random Rubble stone masonry in CM (1:8) prop: (Cement: Sand) using hard granite stones carted from approved quarry including cost and conveyance of all materials like cement, sand, water, stones etc., from approved quarry, to site and including seigniorage charges, sales & other taxes on all materials including labour for cutting stones to required size and shape, mixing, of cement, mortar, construction, curing etc.,and Overheads & Contractors profit complete for finished item of work in foundation and basement. (APSS No. 601 & 615)

Providing Antitermite treatment as per IS 6315 (Part - 2) 2001 (Pre-constructional chemical treatment measures) along the internal & external vertical faces of the columns, plinth beams, basement and top surface of the basement filling below flooring bed as per the specified procedure conforming to IS 6315 (Part-2) 2001 and other relevant approved specification duly using Chlorpyriphos/ Lindane emulsifiable concentrate 20% with 1% concentration @ 7.5 Liters/ sqm of the vertical surface & @ 5.0 Liters/ sqm of the horizontal surface of the substructure to a depth of 500 mm around columns & 300 mm deep around plinth beams, basements & floor filling area including excavation channel along the wall & rodding etc & cost & conveyance of all materials to the site, cost of labour for spraying, rodding etc complete for finished item of work as per the approval of the Engineer-in-Charge

Providing impervious coat over RCC roof slab to required slopes with CM (1:3) prop. 20mm thick (average) mixed with water proofing compound manufactured by reputed manufacturers as approved by Engineer-in-charge at 1Kg/bag of cement, laid over roof slab when it is green, finished smooth with a floating coat of neat cement and thread lining at regular intervals of 45cmx45cm including cost and conveyance of all materials like cement, fine sand(screened), water proofing compound, water etc., to site, seigniorage charges, sales & other taxes on all materials, all operational, incidental and labour charges such as mixing mortar, laying, rounding off at junctions of wall and slab, rendering smooth with thread lining, curing, lift charges, etc., complete for finished item of work (APSS No. 901 & 903).

Brick masonry 230 mm thick for panel walls in superstructure with CM (1:5) proportion using II nd class bricks of size 23x11x7 cm from approved source having crushing strength not less than 35kg/sqcm including cost and conveyance of all materialslike cement ,fine sand ,bricks, water etc., to site , including seignorage charges ,sales and other taxes on all materials and all operational ,incidental and labour charges such as mixing cement mortar, curing scafolding charges, constructing masonary,lift charges,curing etc., complete for finished item of work complete.

Plastering 12mm thick in two coats with base coat of 8mm thick in CM (1:5) and top coat of 4mm thick in CM (1:3) with sponge finishing including cost and conveyance of all materials like cement, finesand(screened), water, etc., to site, cost of seigniorage charges and all other taxes on all materials, and operational, incidental charges and all labour charges for mixing mortar, finishing, scaffolding, lift charges, curing, including cutting grooves etc. as directed by Engineer-in-charge, complete for finished item of work for internal walls(APSS No. 901 & 904)

Plastering 20mm thick in two coats with base coat of 16mm thick in CM (1:6) and top coat of 4mm thick in CM (1:4) with dubara sponge finishing including cost and conveyance of all materials like cement, fine sand (screened), water, etc., to site, cost of seigniorage charges and all other taxes on all materials, and operational, incidental charges and all labour charges for mixing mortar, finishing, scaffolding, lift charges, curing, including cutting grooves etc. as directed by Engineer-in-charge, complete for finished item of work (APSS No. 901 & 904) for external faces of walls.

Providing and applying SYNTHETIC PLASTER PUTTY or equivalent putty such as Birla wall care Putty of average 1 to 2 mm thick over plastered surface to prepare the surface even and smooth after thoroughly brushing the surface to remove all dirt and remains of loose powered materials, applying emery paper sand the surface , clean and wipe off loose dust, applying, knifing paste filler by putty knife / Muslin pad , air dry for 2-3 Hrs., sand with 180 and 320 no emery paper for the surface preparation including cost and coveyance of all materials tomsite, all operational , incidental,labour charges etc., complete for finished item of work for walls

Painting to newWalls with 2 coats acrylic emulsion paint interior grade of approved brand and shade over Priming Coat, making 3 coatsin all to give an even shade after thouroughly brushing the surface to remove all dirt and remains of loose powdered materials, including all operational , incidental charges including cost of brushes and all labour charges etc., complete for internal walls.(All Colours) (APSS No. 912)

Painting to newWalls with 2 coats acrylic emulsion paint weather proof water-based, modified acrylic with silicon additives exterior grade of approved brand and shade over Priming Coat, making 3 coatsin all to give an even shade after thouroughly brushing the surface to remove all dirt and remains of loose powdered materials, including all operational , incidental charges including cost of brushes and all labour charges etc., complete for External walls.(APSS No. 912)

Flooring with vitrified polished floor tiles of 1st quality and make as approved by Engineer-in-charge of size not less than 600 mm x 600 mm , 8-10mm thickness regular finish and normal colours with borders and design as per the approved flooring pattern as directed by the Engineer-In -Charge set over a base coat of CM (1:8) prop. 12mm thick using screened sand over CC bed already laid or RCC roof slab , including neat cement slurry of honey like consistancy spread @ 3.3 kgs per Sqm. and jointed neately with white cement paste to full depth mixed with pigment of matching shade including cost and conveyance of all materials like cement, sand, water, tiles, white cement etc., to site (excluding cost of C.C. bed) including cost of seigniorage charges on all materials, cost of base coat and all labour charges for mixing of cement mortar, laying tiles to required slope as directed by the Engineer- in-charge etc.,and overheads & contractors profit complete for finished item of work. (APSS No.701 & 707)

Providing skirting to new walls to 15cm height with Ceramic Tiles of 7.30mmthick length equal to flooring tile over base coat of CM1:3 of 12mm thick with cement slurry of honey like constistency spread @ 3.30 Kgs per Sqm and jointed with white cement paste mixed with pigment of matching shade to full depth, including cost and conveyance of all materials like tiles, cement,sand, etc complete for finished item of work as per drawings or as directed by hte Engineer in Charge.

Flooring with Non-skid red or white full body Ceramic floor tiles of Size 450 mm x 450 mm and thickness between 7-8 mm and 1st quality of any colour and finish in all shades and designs and design as per the approved flooring pattern as directed by the Engineer-In -Charge, set over base coat of cement mortar (1:8), 12mm thick using screened sand over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3 Kgs per Sqm & jointed neatly with white cement paste to full depth mixed with pigment of matching shade, including cost of all materials like cement, sand , water and tiles etc., complete and overheads & contractors profit complete for finished item of work. (APSS No.701 & 707) for toilets

Providing dadooing to walls with glazed plain coloured wall tiles 1st quality of size with borders as approved by Engineer-in-Charge set over base coat of CM(1:3) 12 mm thick using screened sand with cement slurry of honey like consistency spread at the rate of 3.30 kgs per sqm and jointing with white cement paste mixed with pigment of matching shade to full depth, including cost of all materials like tiles, cement, sand and water etc., complete including seigniorage charges etc., and overheads & contractors profit complete for finished item of work.

Flooring with chequered cement concrete heavy duty tiles confirming to IS:13801 using aggregates, cement, pigments of size 300mm x 300mm and thickness 25mm of any shade as approved by Engineer - In - Charge set over base coat of cement mortar (1:6), 12 mm thick using screened sand over CC bed alredy laid or RCC roof slab including neat cement slurry of honey like consistency spread @ 3.3 kgs per sqm and jointed with neat white cement to full depth mixed with pigment of matching shade including cost and conveyance of all materials like cement, sand, water and tiles etc.,and overheads & contractors profit complete for finished item of work. (BLD-CSTN-9-4)

Supply and fixing doors as per drawings with medium teak wood frame of section 100mm x 65 mm and ISI marked flush door shutters of 30 mm thick single shutter with bond wood solid block board type Core having cross bands and face veneers, hot pressed bonded with water proof phenol formaldehyde synthetic resin factory made conforming to IS 2202-1991 (Part-I) both sides commercial ply with internal lipping on all sides and 1mm thick laminated sheet attached to flush shutter on both sides including cost and conveyance to site of teak wood frame, flush shutter including supply and fixing 6 Nos. MS Z hold fasts of size 300 mm x 40 mm x 5mm including cost of ISI marked Aluminium fixtures of 3 Nos. butt hinges (IS:205) 150mm long, 1 No. aldrop (IS:2681) 300mm long, 1 No. tower bolt (IS:204) of 200 mm x 10 mm dia at top , 2 Nos. 150 mm long handles (IS:208), 1 No. door stopper and 1 No. Rubber / Nylon door stop bushes including fixing the fixtures to door with required number of screws, bolt and nuts including labour charges for fixing the frame in position, fixing the shutter to the frame etc., including overheads & contractors profit complete for finished item of work as per APSS 1001 & 1002 (The vertical frame of door shall be embedded in flooring for a depth of not less than 50 mm) (1000mm x 2100mm) Single Shutter

Providing and fixing 30mm thick RAJSHREE or euivalent brand factory made both side prelam soilid pannel PVC DOOR SHUTTER consisting of frame made out of MS tubes on 19 gauge thicknes and size of 19X19mm for styles, top and bottom rails. MS frame shall have a coat steel primers of approved make and manufacture. MS Frame covered with 5mm thick heat molded "RAJSHREE" prelam pac "C "channel of size30mm thick 70mm wide out of which 50mm shall be flat and 20mm shall tappered in 45 degress angle on either side forming styles, and 5mm thick95mm wide RAJSHREE prelam pac sheet out of which 75mm shall be flat and 20mm shall be tappered in 45 degrees on hte inner side to form top and bottom rail 115mm wide RAJSHREE prelam pac sheet out of which 75mm shall be flat and 20mm shall be tappered on both sides to form lock rail, top , bottom and lock rail shall be provided etihere side the pannel. 10mm(5mmX2) thick, 20mm wide cross pac sheet shall be provided as gap incert for top and bottom rail. pannelling of 5mm thick both side prelam pac sheet to be fitted in hte MS frame welded by cieled to the styles and rails with 7mm(5+2mm) thick into 15mm wide pac sheet beedign on inner side and joined together with solvent cement adhessive etc. an additional 5mm thick pac strip of 20mm wide is to be stuck on interior side of C channel using pac solvent cement adhessive etc complete as per direction of Engineer in Charge, manufactur specification and drawing

Supply and fixing powder coated alimunium sliding window with fixed fan light at top as per approved drawings with all required accessories such as stoppers,bolts,weather stripping etc. for all sizes and sections in accordance with approved drawings and as per IS 1948-1961 with top section of window of size 62mm x 32mm ,1.47mm thick, window side frames of size 61.85mm x 31.75mm,1.50mm thick and bottom frame size 61.85mm x 31.75mm,1.50mm thick sloping outwards for drainage and fixed and sliding shutters with bottom,sides and top with section of 40mm x 18mm ,1.70mm thick,inter locking section 40mm x 28mm x 18mm,1.60mm thick inter locked for weather scaling and mounted on nylon rollers of lift type and fan light top &side sections of size 63.50mmx38.10mm,1.53mm thick, powder coating of all alluminium sections 25mm microns thick and fixing 5mm thick plain glass in fan light and 5mm thick ground glass for shutters fitted with alluminium glazing clips and rubber beading , powder coating of all alluminium sections 25mm microns thick including cost and conveyance to site of powder coated aluminium sections, glass, rubber beading , fixtures etc., including labour charges for manufacturing window, fixing in position using wooden blocks and sheet metal screws, overheads & contractors profit etc., complete for finished item of work. (The aluminium sections used shall be standard make confirming to IS 1948-1961 and as approved by the Engineer and fixtures shall be of ISI marked) (1200mm x 1800mm)

Providing and fixing of top hung Single fixed Ventilators Louvers size of 2’ 0” x 2’ 0” (609.6 x 609.6mm) outer frame box section size of 80 x 45mm made of pre-painted steel (Base steel as per IS 513 of 0.80 mm thick galvanized as per IS 277 with Zinc of 120 GSM), finish painted with a polyester paint of 60-65 microns thick and section for outer frame of 80 x 45 mm, centre mullion of 80 x 60 mm, section for shutter of 52 x 25 mm x 0.6 mm thick, outer frame and mullions to have rebate for glazed shutter with a provision for guard bars/grills and the sections cut to length metre joined with corner bracket, centre mullion fixed with mullion cap, 1 No. of High grade nylon latch handle, window stopper, 2 nos. of with MS Powder coated /SS ball bearing butt Hinges provided per shutter and windows fitted with 4 mm thick plain float glass with rubber gaskets including fixing the frames in concrete/masonry wall by means of self expanding screws, Including 10 mm Square guard bars with 6” (152.4mm) pitch etc., complete for finished item of work.

Supplying and fixing of stainless steel ( grade 304 ) hand railing as per approved drawing with top rail of 50mm dia pipe and 2mm thick medium class and vertical posts of 25mm dia and 1.6mm thick medium class 2 Nos for each step fixed with base plate of 75mm dia using bonding agent and anchor fastner and welding, drilling of 20mm dia holes with pneumatic compressor for fixing railing, buffing, polishing all members of the railing thouroughly , lacquer finishing to present seamless finish including cost and conveyance of all materials, electrodes, welding charges, cost of all consumables, labour charges , overheads & contractors profit etc., complete for finished item of work.

Providing and Fixing Mild Steel, Structural Steel, I.e., Angles, Channels and I sections.of different diameters, cutting and fabricating to required sizes and shapes,placing in position as per approved designs and drawings to be supplied at the time of execution of work, including cost and conveyance of all Mild steel sections and all wastages such as overlaps, couplings, welede joints, etc., and all operational, incidental, Labour charges for fabricating steel works like Window Grills, Compound Wall Grills, Iron Doors, Windows including cost of welding rods, power charges, including cost of Labour charges for fixing Iron Doors, Iron Windows and Window Grills in position etc. complete for finished item of work.

Roofing with plain or corrugated G.I sheets 0.1mm to 0.80mm thick fixed with G.I ‘J’ bolts & nuts 8 mm dia with bitumen & G.I limpet washers filled with white lead &excluding the cost of purlins, rafters, trusses including cost and conveyance of all materials , labour charges , overheads and contractors profit etc., complete for finished item of work in all floors.

Painting to new wood work with three coats of ready mixed synthetic enamel paint first quality after thoroughly brushing the surface to remove all remains of loose powdered materials, including c/c of all materials, site and other taxes, all operational, incidental and labour charges etc., complete for finished item of work . (APSS No.1201,1207 &1212). (CSSR)

Supplying & fixing collapsible steel shutters with vertical, double channel of 20 x10x2 mm of 100 mm centre ,Bracers with flat iron 40x40x6 mm with 38 mm dia steel pulleys, the top, bottom and side vertical frames of the collapsible gate with 65x65mmx8mm MS Angle and middle guide rail at site height with 65mmx8mm MS flat for the pulleys to guide and fixed with locking arrangements, stoppers, handles, all accessories all fixtures and painted with one coat of approved steel primer etc., complete for finished item of work as per special spn 1105

Wiring with 2 runs of 14/03 mm (1.0sq.mm) fire retardant (FR) PVC insulated flexible copper cable (ISI Mark) In existing pipe with 6A switch, control box including all labour charges etc., complete for light, bell, fan and exhaust fan poits in Non- residential buildings(

Supplying and fixing of batten holder / slanting holder in lieu of ceiling rose of light point complete with all connections and all labour charges with 10 W bulb etc., complete for new installation.

Supplying and fixing of 25mm dia 2 mm thick PVC pipe (ISI mark) recessed concealed in roof slabs with all required accessories including masonary work and labour charges ect., complete.

Supplying and erecting exhaust fan light duty 250 V AC 50 Cycles 300 mm (12") 1350 RPM metallic body plastic blades, wire mesh, etc., complete

supply and fixing of 25mm dia 2mm thick PVC pipe(ISI) concealed in wall with all required accessories including masonary work and labour charges etc., complete

Supplying and fixing of size 15"*20"TW peeta board including 3Nos,63amp 415 V porcalain rewirable fuse unit and 63A N Link including cost and conveyance of all material and all labour charges etc.. Complete.

supply and fixing TPN Distribution boadrd with IP-42 protection (metal door) suitable for 3 phase ELCB/RCCB/FP isolator as incomer and 10ka SP MCBs as outgoing including internal connection and labour charges for surface/flush mounting etc., complete

supplying and fixing of ceiling fan1200mm(48") sweep230v, a.c Hz with 3 blades and double ball bearings with all standard accessories.(crompton make high speed)

Supplying and erecting of resistance approved make fan stop regulator for ceiling fans 1200mm sweep complete erected on existing boared labour charges etc., complete.

Providing earth electrode of low carbon steel rod, UL listed of 17.2 mm dia, 3 Mtr long, coated with copper of 254 microns thickness, CPRI tested for short time current withstand test of 25 kA, coating thickness, environmental test (Salt Mist Test), Bend test, Tensile strength, Yield / tensile ratio, Electrical Resistivity test, complete with clamps and 2 bags of (Earth plus ULTRA /TIRUMALA) high grade earthing compound IEC 62561-7 complaint Eco-friendly, Maintenance free, anti-corrosive, lead-free, super conductive, mineral based high-grade earthing compound, to enhance soil conductivity. With resistance <0.20 ohms-meter, should be leach proof & Sulphur free complete with earth inspection chamber of dimensions: width: 320 mm x 320 mm, Height : 192 mm, weight : 30 Kgs, Load bearing capacity : 5000 Kgs

Supplying and erecting 100 A - 415 V fues unit in approved manner as directed by the department including Cost & Conveyance of all materials and labour charges etc., complete. (Sl.No203)

Supply and fixing of 20W, 2400 lumens, T8 not less than 1100 mm length LED retrofit tube light with aluminum anodized body, input voltage AC 220 - 260 Volts, having luminous efficacy >=90 lumens/ watt, with PF>0.9, surge protection: 2KV, THD<10%, with inbuilt driver and frosted cover CCT: 3000K-5700K, minimum CRI>70, etc., as per IS 10322 (Part 5/ Sec 1), 2012, complete with earth connection and not less than two years warranty. Makes: As per list of recommended brands as category II.

Supply and fixing of 6A 3 pin wall plug socket with 6A switch control on a common switch board with earth continuity including wire leads, earth connections along with all labour charges etc., complete.

Supply and Fixing of 16/20A Modular 1 way combi Socket with shutter and 16A / 20A 1 Way Modular Switch duly recessed in wall with 4 Modular Box and 3 modular cover frame including earth connections and all labour charges etc., complete. Make: Legrand Arteor / MK Blenge

Supply and run of 2 of 36/0.3mm ( 2.5 Sq.mm) FR P.V.C. insulated flexible copper cable in existing pipe for mains inlcuding all labour charges etc., complete. BLD-ELEC-3.1.4

Supply and run of 2 of 56/0.3mm (4 Sq.mm) FR P.V.C. insulated flexible copper cable in existing pipe for mains inlcuding all labour charges etc., complete. BLD-ELEC-3.1.5

Supply and run of 2 of 84/0.3mm (6 Sq.mm) FR P.V.C. insulated flexible copper cable in existing pipe for mains inlcuding all labour charges etc., complete. BLD-ELEC-3.1.6

Supply and run of 2 of 140/0.3mm ( 10 Sq.mm) FR P.V.C. insulated flexible copper cable in existing pipe for mains inlcuding all labour charges etc., complete. BLD-ELEC-3.1.4

Supply and Transportation of 40W LED Post top lantern made with cast Aluminum with decorative opal polycarbonate diffuser with IP 65 protection etc., complete with all accessories with not less than two years warranty. Makes: As per list of recommended brands.

Supply and Fixing of Ashirvad/ Ajay/ Astral Flowguard or equivalent CPVC Pipes and Fittings to meet the requirement of ASTM-D 2846 and are produced in CTS (Copper Tube Sizes 1/2" ton 2" Ashirvad Flowgurard SDR 11 and SDR 13.5 pipes are made from idential CPVC compounds having the same physical Properties for Hot and Cold Water (IS 15778:2007) ( BMW-I.222,221,220) (28.60mm OD Pipe)

Supply and Fixing of Ashirvad/ Ajay/ Astral Flowguard or equivalent CPVC Pipes and Fittings to meet the requirement of ASTM-D 2846 and are produced in CTS (Copper Tube Sizes 1/2" ton 2" Ashirvad Flowgurard SDR 11 and SDR 13.5 pipes are made from idential CPVC compounds having the same physical Properties for Hot and Cold Water (IS 15778:2007) ( BMW-I.222,221,220) 22.20mm OD Pipe

Supplying & Fixing Indian make Flat Back Wash Hand Basin 1st quality conforming to IS:2556-Part-4:1972 with waste fittings like rubber plug, chain, 32 mm nominal size C.P. Fitting with parallel pipe thread conforming to IS:2963-1979 and fitted with 15 mm nominal bore Chromium Plated Pillar Tap of 1st quality Indian make 400 grams Seiko/ Senior/ Nice/ Esso or equivalent complete with standard CI brackets including wooden block: 550 x 400 mm - Single C.P. Pillar cock. (BMW-D-24)

Supplying and fixing of PVC pipe of specified size including cost and conveyance of all materials, labour charges etc complete as per drawings or as directed by the Engineer in Charge. 38.1 mm Dia Pipe

Supplying and fixing of PVC pipe of specified size including cost and conveyance of all materials, labour charges etc complete as per drawings or as directed by the Engineer in Charge. 75 mm Dia Pipe:

Supplying and fixing of PVC pipe of specified size including cost and conveyance of all materials, labour charges etc complete as per drawings or as directed by the Engineer in Charge 110 mm Dia Pipe:

Supplying and fixing low down porcelain flushing tank 10 lit capacity Hindustan Sanitary ware/parry/Neycer with internal components etc complete

Supplying and fixing TV shape mirror with plastic frame size 609.6 mm x 457 .2 mm including cost and conveyance of all materials and labour charges etc., complete.

Providing and placing on terrace (at all floor levels) polyetheylene water storage tank with double layer approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet and outlets and over flow pipes but without fittings and base support for tanks including cost and conveyance of all materials and labour charges , overheads & contractors profit complete for finished item of work.

Constructing 904.0 mm (3’0”) dia brick masonry inspection chamber as per IS - 4111: Part-1:1986 with cement mortar (1:6) prop using 2nd Class Clay Bricks of 225 mm thick from approved source having a minimum crushing strength of 5 N/sq.mm including plastering with cement mortar 1:3 prop; ½” thick both inside and outside fitted with 20” dia RCC manhole covers and frames including excavating pits up to a depth of 904 mm (3'-0") in all sorts of soils (excluding rock) and laying cement concrete (1:4:8) 150 mm thick using 40 mm HBG Metal and P.C.C. 1:2:4 benching and channel 100 mm thick as per Standard specification and including cost and conveyance of all materials like cement, sand, bricks, water etc., to site, cost of seigniorage charges on all materials and all incidental and operational, labour charges like mixing cement mortar, constructing masonry, lift charges, curing etc., complete for finished item of work as per Standard specification.

S&F 12.7mm N.P bib tap Indian make heavy duty including cost and conveyance ao all materials and labour charges etc

Supplying and Fixing European Water Closet of 1st quality conforming to IS:2556-Part-2-1973 of Hindustan / Neycer or Parryware make white glazed with 'S' trap (BMW-D.15)

Supply & Fixing 25.4mm dia &609.6mm long aluminium anodized towel rod with brackets and aluminium screws site, labour charges, overheads & contractor's profit complete for finished item of work.

Supply & Fixing NP soap dish heavy type with NP SCREWS, labour charges, overheads & contractor's profit complete for finished item of work.