REPAIR MAINT MANNING AND OPERATION OF STP AND SEWAGE PUMP UNDER GE EAST BAREILLY

Amount

Dewatering and pumping out of existing accumulated sewage/sludge at STP MH of Capacity 150 KLD from Tube Settler tank by manullay or using external sewage disposal pump sets to near by sewage disposal drain and cleaning of tanks by scrapping with wire brush or any other means on walls and bottom of tank and removing the sludge / silt / sand / fungus etc deposited inside the sumps / tanks with buckets and depositing where directed, including removing duck media and followed by cleaning with bleaching water solution and fresh water and finally applying one coat of snow cem on internal and external surfaces including writing the date of cleaning and due date of cleaning in white colour on black background on external walls after that replacing of duck media with new as per existing complete all as specified and directed. Note:- (a) The followings are deemed to be included in the rate quoted. (i) Removing and disposal of old Tube Deck Media and replacement with new . (ii) The disposal of accumulated/deposited sludge after drying out side the defence land to a distance exceeding 1.5 KM and not exceeding 5.00 KM from the STP. (iii) Before commencement of work, necessary arrangement for disposal of sewage/sludge be made and work to be carried out in fast pace by deploying more man power at STP in order to complete the work in max 02 days. (v) Cutting and rewelding of supporting MS frame structure. (b) Replacement of unsv rusted portion of supporting MS frame structure.Cost of MS fame will be paid saperetly

All as per Ser item No.1 here-in-before but STP 80 OR of Capacity 150 KLD

Dewatering and pumping out of existing accumulated sewage/sludge at STP JRC OR of Capacity 01 MLD from Tube Settler tank by manullay or using external sewage disposal pump sets to near by sewage disposal drain and cleaning of tanks by scrapping with wire brush or any other means on walls and bottom of tank and removing the sludge / silt / sand / fungus etc deposited inside the sumps / tanks with buckets and depositing where directed, followed by cleaning with bleaching water solution and fresh water and finally applying one coat of snow cem on internal and external surfaces including writing the date of cleaning and due date of cleaning in white colour on black background on external walls complete all as specified and directed. Note:- (a) The followings are deemed to be included in the rate quoted. (i) The disposal of accumulated/deposited sludge after drying out side the defence land to a distance exceeding 1.5 KM and not exceeding 5.00 KM from the STP. (iii) Before commencement of work, necessary arrangement for disposal of sewage/sludge be made and work to be carried out in fast pace by deploying more man power at STP in order to complete the work in max 02 days. (iv) Refixing of old serviceable tube settler media . (v) Cutting and rewelding of supporting MS frame structure.

Dewatering and pumping out of existing accumulated sewage from Chlorine Contact Tank and Treated Water Tank at STP 80 OR of capacity of 150 MLD by manullay or using external sewage disposal pump sets to near by sewage disposal drain and cleaning of tanks by scrapping with wire brush or any other means on walls and bottom of tank and removing the sludge / silt / sand / fungus etc deposited inside the sumps / tanks with buckets and depositing where directed, followed by cleaning with bleaching water solution and fresh water and finally applying one coat of snow cem on internal and external surfaces including writing the date of cleaning and due date of cleaning in white colour on black background on external walls complete all as specified and directed. Note :- (i) The accumulated/deposited sludge after drying shall be disposed off out side the defence land to a distance exceeding 1.5 KM and not exceeding 5.00 KM from the STP cost of which shall be deemed to enclusive in the quoted rate and nothing extra shall be paid on this account. (ii) Contractor is to arrange own diesel pump, T&P etc for cleaning purpose and minor spares and consumable like small screws, washers, cleaning agents consumables etc is deemed to be included in the cost, the unit rate quoted deemed to be include all safety precautions to be taken while working in STP. (iii) Before commencement of work, necessary arrangement for disposal of sewage/sludge be made and work to be carried out in fast pace by deploying more man power at STP in order to complete the work in max 02 days.

All as per Ser item No.4 here-in-before but STP MH OR of Capacity of 150 KLD

All as per Ser item No.4 here-in-before but STP JRC of Capacity 01 MLD

Dewatering and pumping out of existing accumulated Sludge and Water from Sludge Holding Tank at STP 80 ORs of Capacity of 150 KLD by using external sewage disposal pump sets to near by sewage disposal drain and cleaning of tanks by scrapping with wire brush or any other means on walls and bottom of tank and removing the sludge / silt / sand / fungus etc deposited inside the sumps / tanks with buckets and depositing where directed, followed by cleaning with bleaching water solution and fresh water and finally applying one coat of snow cem on internal and external surfaces including writing the date of cleaning and due date of cleaning in white colour on black background on external walls complete all as specified and directed. Note:- (i) The accumulated/deposited sludge after drying shall be disposed off out side the defence land to a distance exceeding 1.5 KM and not exceeding 5.00 KM from the STP cost of which shall be deemed to enclusive in the quoted rate and nothing extra shall be paid on this account. (ii) Before commencement of work, necessary arrangement for disposal of sewage/sludge be made and work to be carried out in fast pace by deploying more man power at STP in order to complete the work in max 02 days. (iii) Contractor is to arrange own diesel pump, T&P etc for cleaning purpose and minor spares and consumable like small screws, washers, cleaning agents consumables etc is deemed to be included in the cost, the unit rate quoted deemed to be include all safety precautions to be taken while working in STP.

All as per Ser item No.1 here-in-before but STP MH OR of Capacity of 150 KLD

All as per Ser item No.1 here-in-before but STP JRC of Capacity 01 MLD

Dewatering and pumping out of existing accumulated Sludge and mud including cutting of grass, bushes, plant growth from Sludge Drying Beds at STPs under GE east bareilly by using external sewage disposal pump sets to near by sewage disposal drain and cleaning of tanks by scrapping with wire brush or any other means on walls and bottom of tank and removing the sludge / silt / sand / fungus etc deposited inside the sumps / tanks with buckets and depositing where directed, followed by cleaning with bleaching water solution and fresh water and finally applying one coat of snow cem on internal and external surfaces including writing the date of cleaning and due date of cleaning in white colour on black background on external walls complete all as specified and directed. Note:- (i) The accumulated/deposited sludge after drying shall be disposed off out side the defence land to adistance exceeding 1.5 KM and not exceeding 5.00 KM from the STP cost of which shall be deemed to enclusive in the quoted rate and nothing extra shall be paid on this account. (ii) Before commencement of work, necessary arrangement for disposal of sewage/sludge be made and work to be carried out in fast pace by deploying more man power at STP in order to complete the work in max 02 days. (iii) Contractor is to arrange own diesel pump, T&P etc for cleaning purpose and minor spares and consumable like small screws, washers, cleaning agents consumables etc is deemed to be included in the cost, the unit rate quoted deemed to be include all safety precautions to be taken while working in STP. (iv) Cleaning of sludge transfer line from tube settler tank to Sludge holding tank

Supply and fix in replacement of Glass tube type Air Rotameter including taking down existing unserviceable Air Rotameter of any description complete all as specified and directed. Make: Flowstar / Microflow / Aster

M&L for replacement of Unsv MBBR Media from the tank and supply of filling Fresh media of MBBR Media in the main reactor as specified of existing /suitable Make with the following specificatios:- Effective surface area of media Approx - 400 Sqm/Cum (b) Media ht Approx - 15 mm (c)Media dia Approx- 22 mm (d) Weight per unit surface area approx -22 mm (e) Voidage - >093 gm/Cucm (g) Media fill Range - 25-55% of volume

S&F in replacement, heavy duty cloth strips of filter press as per existing frame of capacity of 01 MLD and complete over hauling of filter press including testing complete all as specified and directed.

S&F in replacement, medium duty manually operated chain pulley block 1 Ton capacity, 10 Mtr standard lift complete all as specified and directed confirming to IS-3832-1986

Supply and fixed in replacement, connecting and testing of (non return valve ISI - 5312) CI of 150 mm sizes bore pipe heavy duty both end flanged of pressure rating PN 1.6 and jointing with joint with rubber or fibre board gasket complete with and including required nos size of nuts, bolts and washers complete all as specified and directed by Engineer-in-charge

Supply and fix in replacement of CI Butterfly valve of following size as per IS 13095, PN 16, wafer type without lugs, suitable for clamping between flanges as per ANSI B 16.1 CI-125, including flanges, fittings, gasket, nuts, bolts, washers etc. including taking up / down of existing unserviceable butterfly valve of any description complete of size 50 mm all as specified and directed. Make : Leader / Crawley / Audco / L&T / Zoloto

All as per Ser item No.16 here-in-before but 100 mm

All as per Ser item No.16 here-in-before but 150 mm

Material and labour for M.S. Black Pipe plain end as per IS:1239 (I), nominal bore with following dia, heavy Grade (' C' class) with all fittings like elnow, tee reducer, flange nut bolt with washer including cutting, welding and joining etc as per site requirement and applying two coats of synthetic enamel paint of approved colour over a coat of red oxide primer including taking up / down of existing unserviceable pipe of any description complete of size 80mm all as specified and directed. Note:- fixing of pipe line will be carried out on wall or floor and cost of the same will be deemed to be included in tthe rate quoted however for the pipe line laid under ground by digging trench will be paid saperately.

All as per Ser item No.19 here-in-before but 100 mm

All as per Ser item No.19 here-in-before but 150 mm

M&L for Structure Steel Work, made out of god quality-A RolledMild Steel Chanel, Angle or Tee Sections, MS Sheet with hinges & looking arrangements et. Cut to shape / ordinary length, drilled and counter sunk for screws / Bolts, including bending and welding duly painted with 2 coats of anticorrosive synthetic enamel paint over a coat of Zinc Chromate as in framed work with MS Sheet cover complete all as specified and directed.

Supplying and fixing of Stainless steel Pipe of size 50 mm bore fixing on wall/well etc for all as specified and directed

M&L for complete overhouling and repairing of multigrade sand filter with replacement of filter media as per existing and activated carbon filter media including replacement of filter media including other connected assessories as required at site of STP capacity of 1 MLD and STP 80 OR including testing and wire mesh size shuold as per existing .,colour in Black ,Grade of GAC 8x30 and bulk density approx 450kg /cum, Hardness( abrasion number) approx 95-99 and PH value - 7 complete all as specified and directed

M&L for complete overhouling and repairing of multigrade sand filter with replacement of filter media as per existing and activated carbon filter media including replacement of filter media including other connected assessories as required at site of STP capacity of 150 KLD STP MH including testing and wire mesh size shuold as per existing .,colour in Black ,Grade of GAC 8x30 and bulk density approx 450kg /cum, Hardness( abrasion number) approx 95-99 and PH value - 7 complete all as specified and directed

M&L for cleaning, scrapping out side of vessel properly including painting with one coat zinc chrome primer & two coats of best quality synthetic enamel paint etc. complete all as specified and directed

M&L for servicing / maintenance of air compressor machine including 30 HP, 415 volts 50 Hz motor complete with cleaning of air tank incl replacement of all defective parts and lubricating oil complete all as specified and directed. Note :- Spare parts will be measured and paid under relevant item separately. All minor consumables incl T&P and Tpt required shall be deemed as included in the rates quoted.

All as per Ser item No. 27 here-in-before but Cap 515M3/Hr with 10 HP motor.

Supply only rotor roller machineing and alignment complete all as specified and directed.

Supply only all packing for casing complete all as specified and directed.

Supply only air filter complete all as specified and directed.

Supply only 'O'-Ring complete all as specified and directed.

Supply only oil seal complete all as specified and directed.

Supply only Gear wheel pair complete all as specified and directed.

Supply only lock nut complete all as specified and directed.

Supply only lock washer complete all as specified and directed.

Supply only ball bearing No. 2211complete all as specified and directed.

Supply only ball bearing No. 3211complete all as specified and directed.

Supply only ball bearing No. 6211complete all as specified and directed.

Supply only V belt complete all as specified and directed. Make Fainiyar

M&L removing the submersbile pump set from existing position, Shifting to authorised workshop for repair work, dismantle/open, removing the burnt winding, cleaning of rotor /stator, re-winding the motor with F Class insulation super enameled copper wire of size equivalent to the original winding incl insulate packing materials, Varnishing, Drying incl replacement of both water seal, compound, both bearing, fill with new lub oil etc. re-assembling the pump set, installing back to the original position, testing and commissioning on full load for 4 hrs continuous running for the motor cap of motor upto 3 HP complete all as specified and directed. Note :- Spares parts will be measured and paid under relevant items separately all minor consumable/Eqpt/Tpt required shall be deemed as included in the rates quoted.

All as per Ser item No. 41 here-in-before but more than 3 HP and upto 5 HP.

All as per Ser item No. 41 here-in-before but more than 7.5 HP and upto 11 HP.

All as per Ser item No. 41 here-in-before but more than 11 HP and upto 15 HP.

All as per Ser item No. 41 here-in-before but more than 15 HP and upto 20 HP.

M&L for removing the submersbile pump set from existing position, Shifting to authorised workshop for repair work, overhauling and servicing of submersible pump set with motor incl replacement of unsv nuts, bolts & washers, seals, packing, opening of delivery casing volute for checking of non clog type impeller checking & replacement of stuffing box unit seals and match seal housing /casing cover for checking/filling of suitable grade lubricating oil upto required, checking of seat & replacement of seat ring, checking for smoothness of motor runnning and clearance between impeller and casing ring and casing cover, greasing of flower bearing of pump set, incl cleaning of 3 phase electric submersible squirrel cage induction motor in water tight housing testing it for its water tightness by air for its joints incl replacements of unsv parts as required re-assembling the pump set, installing back to the original position testing and commissioning on full load for 4 hrs continuous running for the motor cap of motor upto 3 HP complete all as specified and directed. Note :- Spares parts will be measured and paid under relevant items separately all minor consumable/Eqpt/Tpt required shall be deemed as included in the rates quoted

All as per Ser item No. 46 here-in-before but more than 3 HP and upto 5 HP.

All as per Ser item No. 46 here-in-before but more than 5 HP and upto 20 HP.

Supply only Non Clog impeller suitable for and upto 3 HP submersible pump set complete all as specified and directed.

All as per Ser item No. 49 here-in-before but more than 5 HP and upto 7.5 HP.

All as per Ser item No. 49 here-in-before but more than 7.5 HP and upto 11 HP.

All as per Ser item No. 49 here-in-before but more than 11 HP and upto 15 HP.

All as per Ser item No. 49 here-in-before but more than 15 HP and upto 20 HP.

Supply only upper/lower or back to back roller or Ball bearing suitable for and 3 HP to 30 HP non clog submersible pump set complete all as specified and directed. Make FAG/SKF

Supply only Mechinical seal carbonite 25 mm suitable for and upto 3 Hp to 5 HP non clog submersible pump set complete all as specified and directed

Supply only Mechinical seal carbonite 33 mm suitable for and 5HP to 20 HP non clog submersible pump set complete all as specified and directed

Supply only oil seal 2 HP to 20 HP non clog submersible pump set complete all as specified and directed.

M&L for dismantling and removing the motor of the mono block / coupled Pump set or Air Compressor from existing position, Shifting to authorized workshop for the repair work, removing the burnt wirding cleaning rotor/stator, re-winding the motor with super enameled copper wire of size equivalent to the original winding incl insulate packing materials, Varnishing, Drying etc incl installing back to the original position, testing and commissioning on full load for 4 hrs continuous running for the motor cap of motor upto 3 HP complete all as specified and directed.

All as per Ser item No. 58 here-in-before but more than 7.5 HP and upto 10 HP.

All as per Ser item No. 58 here-in-before but more than 30 HP.

M&L for Dismantling and removing the mono block / Coupled pump set from the existing position after disconnecting the inlet/outlet pipe connections, disconnecting the electric supply cables and transporting to repair work shop complete, opening the pump side, servicing the pump set including cleaning the shaft including replacement of worn out bearing, bushes, check nut, shaft sleeves etc. and installing back to the original position, testing and commissioning on full load for 4 hrs continuous running for the capacity of pump upto 3HP complete all as specified and directed. Note: Spares parts will be measured and paid under relevent item separately. All minor consumables / Eqpt /Tpt required shall be deemed as included in the rates quoted.

All as per Srl item No 61 here-in-before but more than 3HP upto 5HP

All as per Srl item No 61 here-in-before but more than 5HP upto 15 HP

Supply only Ball bearing of suitable size for and upto 3HP mono block / Coupled pump set. Make: SKF / NBC complete all as specified and directed.

All as per Srl item No 64 here-in-before but more than 3HP upto 5HP

All as per Srl item No 64 here-in-before but more than 5HP upto 7.5HP

Supply only brass bush of suitable size for and upto 3HP mono block / Coupled pump set complete all as specified and directed.

All as per Srl item No 67 here-in-before but more than 3HP upto 5HP

All as per Srl item No 67 here-in-before but more than 5HP upto 7.5HP

All as per Srl item No 67 here-in-before but more than 7.5 HP upto 10HP

All as per Srl item No 67 here-in-before but more than 10 HP upto 12.5 HP

Supply only new impeller of suitable size for and upto 3HP mono block / Coupled pump set complete all as specified and directed.

All as per Srl item No 72 here-in-before but more than 3HP upto 5HP

All as per Srl item No 72 here-in-before but more than 5HP upto 7.5HP

All as per Srl item No 72 here-in-before but more than 7.5HP upto 10HP

All as per Srl item No 72 here-in-before but more than 10HP upto 15HP

M & L in repairs for Gland packing of thickness upto 14mm complete all as specified and directed. Make: Spitmaan Graflon / Charminar / Champion

M&L in repairs Air Cobe , suitable size for mono block / Coupled pump set, made out of brass, as per site complete all as specified and directed.

M&L for cleaning and desiIting the sewage lift well of up to 100 cum capacity ,dewatering the complete well furniture yard STP and well of Map area removing all the deposited sludge, soil and other material from the well including bailing / pumping out muddy water from the well by manually or by providing suitable pump sets from bottom level of well, scrapping out the scales / deposits from inner surface of the well throughly, washing with bleaching powder and soda ash, cleaning / bailing out settled materials completely by any means and removing sludge to a distance up to 3 km out side of defence land limit and dispose off in low lying area including dewatering as required including writing 'Tank cleaned on ......(date) with 10 cm size white letter on black surface by engaging skilled artist using first quality synthetic enamel paint complete all as specified and directed Note:- (i) Contractor is to arrange own diesel pump, T&P etc for cleaning purpose and minor spares and consumable like small screws, washers, cleaning agents consumables etc is deemed to be included in the cost, the unit rate quoted deemed to be include all safety precautions to be taken while working in Lift well. (ii) The accumulated/deposited sludge after drying shall be disposed off out side the defence land to a distance exceeding 1.5 KM and not exceeding 5.00 KM from the Lift well cost of which shall be deemed to inclusive in the quoted rate and nothing extra shall be paid on this account. (iii) Before commencement of work, necessary arrangement for disposal of sewage/sludge be made and work to be carried out in fast pace by deploying more man power at lift well in order to complete the work at the earliest.

All as per Srl item No79 here-in-before but for 100 CuM upto 175 CuM capacity

All as per Srl item No 79here-in-before but more than 175 CuM upto 200 CuM capacity

All as per Srl item No 79 here-in-before but STP Collection tank/Equalisation tank of capacity

All as per Srl item No 79 here-in-before but more STP Collection tank of STP MH

All as per Srl item No 79 here-in-before but STP Equalisation tank of capacity of 150 KLD at STP 80 Ors

M&L for preparing the surface by scrapping the old painting and removing the grease, oil, dirt, algae etc. Painting of outer surfaces of MS pipes with one coat of black Japan paint over a coat of Zync Chromate complete incl its MS supports / clamps / nuts / bolts and marking / writing flow arrows and name with white paint by skilled painter All as directed of 150 - 200 mm dia complete all as specified and directed.

All as per Srl item No 85 here-in-before but 80 to 100 mm dia

All as per Srl item No 85 here-in-before but 50 mm dia

All as per Srl item No 85 here-in-before but 25 mm dia

S&F in repair and connect, MCB SP 6 to 32 A, AC, 240V, ISI Marked complete all as specified and directed.

S&F in repair and connect, Isolator DP, 40A, AC, 240V, ISI Marked complete all as specified and directed.

S&F in repair and connect, Isolator 4P, 63A, AC, 415V, ISI Marked complete all as specified and directed.

S&F in repairs and connect, Single Phase Preventer suitable for motor protection complete all as specified and directed.

S&F in repairs and connect, NO-NC auxiliary contact block suitable for 10 to 25A 3 phase contactors complete all as specified and directed..

S&F in repairs and connect, NO-NC auxiliary contact block suitable for 32 to 60A 3 phase complete all as specified and directed.

S&F in repairs and connect, over load Relay 3 Phase, 415V, 25 Amp to 40 Amp complete all as specified and directed.

S&F in repairs and connect, DOL starter suitable 2 to 7.5HP motor, 3 Phase, 415 V, with 1Ø preventer and thermal relays complete all as specified and directed.

All as per Srl item No 96 here-in-before but for more than 10 to 15HP

S&F in repairs, fully automatic star delta motor starter suitable for 15/ 20 HP pump set, 3 phase, 415 V with relay of suitable range incl enclosure. Make : L&T, model No. ML- 4FASD or equivalent of C&S / Legrand complete all as specified and directed.

S&F in repairs, 3 Pole MCCB 25 -100 Amp, 50 Hz, 415 V with rupturing capacity 18KA with Thermal - Magnetic Release. complete all as specified and directed.

All as per Srl item No 99 here-in-before but 4 Pole 100-200Amps. 25KA

S&F in repairs, testing Volt meter 0-500 Volts complete all as specified and directed. Make: AE/ Rishab/Meco/Enercon.

S&F in repairs, Pressure Gauge, 100/80 mm dia, 0 - 100 lb/Sq inch pressure rating complete all as specified and directed. Make: Lub / Meco / H Guru / Pfizer

Supply and fixing of non clog sewage submersible pumpset, 2HP, 1Ø, AC, 240V, complete all as specified and directed. Make: CG/ Kirloskar / KSB

Supply only DWPE (Dewatering Polyelectrolyte) powder, pack of 10/25Kg in polythene bags / HDPE drums complete all as specified and directed

Supply only Calcium Hypo chlorite 65%-70% chlorine content in granular disinfectant for water treatment in 45 kg Drums etc complete all as specified and directed.

Supply only Calcium Hydro-Oxide (Lime, 80-85%) in Powder form as pH Booster for STP water, packing in 40 Kg Packs complete all as specified and directed.

Supply only Ortho Tolidin solution ( 500ml) for testing of dissolved chlorine in water complete all as specified and directed

Supply only Chlorination testing glass test Tube kit complete all as specified and directed

Supply only Alum Ferric (Grade-4) (best quality as per sample) for purification of water (containing lead (as PB) 30 ppm Max and arsenic 6 ppm Max) confirming to IS-299/2012 (Revised) as amended upto date complete all as specified and ddirected by Engineer-in-Charge. (Note :- The Alumino Ferric Sulphate shall be supplied in superior quality bricks (slabs) as per IS specifications. Manufacturers Name/trade mark shall be engraved on each brick (slab) in addition to marking of relavant clause of IS specification).

S&F "No Entry" board of size 200mm x 650mm of thickness 3 mm MS Plate duly painted on both sides alongwith necessary fixing arrangements for STPs as per sample complete all as specified and directed.

Supply only bacteria culture areobic in 30 Kg of drum complete all as specified and directed

Supply only DAP fertiliser for day to day use in sewage treatment plant complete all as specified and directed .

Supply only molasses for day to day use in Sewage treatment plant complete all as specified and directed .

Supply only PAC (Poly Aluminium Chloride AC 1005 in organic soluable Polymer Powder packed in 25 Kg Poly bags completed all as specified and directed.

M&L for testing of treated sewage water from out let of chlorine contact tank once in every three months from NABL accredited authorized lab as per IS 3025 for recording essential parameters such as BOD, COD, PH, suspended solids and total dissolved solids complete for STP JRC ,80 OR and MH all as specified & directed.

Supply only compressor oil 320 grade complete for top up oil level all as specified and directed .

Supply and fixing Air Compressor of capacity 2 HP single phase 230 Volts and Mixer of filter press machine including all connection with cake formation machine complete all as specified and directed

Supply & fix in repair push button switch with mounting adaptor complete 230 volt complete all as specified and as directed. Make-L & T/Kaycee./BCH

M&L for cleaning panel board busbar and de carbounising of panel board and replacement of unsv parts including wiring and testing complete all as specified and as directed.

M&L for taking out unserviceable Air diffuser and replacement with new one air diffuser complete as per existing all as spefified and directed

M&L for complete overhouling and repairing of cake formation Machine and air Compressor of capacity 2 HP to 3 HP and all the connection of chemical mixer including other connected assessories as required at site for STP JRC Capacity of 1 MLD as specified and directed. Note:- 1. Payment will be made after testing of forming of cake

Supply and fixing of Filter press Plate as per existing size in Cake formation machine complete all as specified and directed

M&L for complete overhouling and repairing of multigrade Pressure sand filter including replacement of filter media as per existing including other connected assessories as required at site of STP capacity of 1 MLD and STP 80 OR including testing complete all as specified and directed

M&L for complete overhouling and repairing of multigrade Pressure sand filter including replacement of filter media as per existing including other connected assessories as required at site of STP capacity 150 KLD of MH STP including testing complete all as specified and directed

Disconnecting Electric motor capacity 30 HP of Air Compressor of any make from STP JRC by arranging /removing from the existing position, opening up, cutting and removing of the burnt out winding conductor, rewinding of the same with same size and gauge of super enamelled copper conductor, insulating, varnishing, cleaning,, greasing, refixing back to its original position, reconnecting back and testing complete all as directed by Engrineer-in-charge.

Disconnecting Electric motor Capacity 10 HP of Air Compressor of any make from STP JRC by arranging dummy plates to suction and delivery line, removing from the existing position, opening up, cutting and removing of the burnt out winding conductor, rewinding of the same with same size and gauge of super enamelled copper conductor, insulating, varnishing, cleaning,, greasing, refixing back to its original position, reconnecting back and testing complete all as directed by Engrineer-in-charge.

Supplying and fixing in repair Switch Gear Change over of 400 Amps 3 Pole 415 volts complete all as specified and directed

Supplying and fixing Contactor 50 Amps 220 Volts all as specified and directed

Supplying and fixing in repair single phase preventor all as specified and directed

M&L for Disconnection flange of MS pipe and replacement of rubber packing to arrest the leakage of 50mm to 100 mm all as specified and directed

Supply and fixing Non Clog Submersible pump of capcity 1 HP single Phase 220 Volts all as specified and directed

Providing operator for operation running of capacity of 1 MLD STP (incluidng operation of valves in Furniture Yard STP ) comprising of control Panel/valves, submersible pump/Motor of capacity min 2 HP to 20 HP, Dosing Plant , bleaching powder dozer,Air Blowers LT panel boards for filling water in aireation tank,MBBR tanks Clear water tank ,ACF,PSF and Treated water twice in a day (ie 2 shifts by employing 01 operator per shift for each STP JRC and supplying dosed water (4 PPM) at pump house twice a day hrs 1000 - 1800 hrs and 1800 hrs to 2 00 hrs )Each Shifts of 8 hrs and including maintaining log sheet and other record complete all as specified and directed Note ( One Opertor per shift for STP JRC and will also responsible to run Sewage sump of Furniture yard STP at same shift without any extra cost to Govt. Note Manning and operaion will be started from month of September 2021 for 04 months

Providing operator for operation running of capacity of 250 KLD 80 ORs STP comprising of control Panel/valves, submersible pump/Motor of capacity min 2 HP to 20 HP, Dosing Plant , bleaching powder dozer,Air Blowers LT panel boards for filling water in aireation tank,MBBR tanks Clear water tank ,ACF,PSF and Treated water twice in a day (ie 2 shifts by employing 01 operator per shift for each STP 80 ORs and supplying dosed water (4 PPM) at pump house twice a day hrs 1000 - 1800 hrs and 1800 hrs to 2 00 hrs )Each Shifts of 8 hrs and including maintaining log sheet and other record complete all as specified and directed Note ( One Opertor per shift for STP 80 ORs and will also responsible to run Sewage sump of Furniture yard STP at same shift without any extra cost to Govt. Note :- Manning and operaion will be started from month of september 2021 (for 04 months)

Supplying and fixing of Stainless steel Pipe of size 25 mm to 32 mm fixing on wall/well etc for all as specified and directed

Excavating in trenches, n exc 1.5m wide and n exc 1.5 m depth; for foundation, etc. or for laying of pipe/cable etc. n exc 10 sq m on plan and n exc 1.5m in depth and getting out in hard/dence soil complete all as specified and directed.

Excavating in trenches, n exc 1.5m wide and n exc 1.5 m depth; for foundation, etc. or for laying of pipe/cable etc. n exc 10 sq m on plan and n exc 1.5m in depth and getting out in Soft /Loose soil complete all as specified and directed.

Returning filling in, Including spreading, levelling,. Watering and well ramming soil in layers not exceeding 25 cm thick, complete all as specified and directed.

Removing excavated material (i.e. soil) from site to a distance n. exc 50 mtrs away and depositing where directed at a level n. exc. 1.5 mtr above the starting point, complete all as specified and directed

M&L for plain cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in coping including use and waste of form work complete all as directed

Taking out old unserviceable MS pipe and supply and lay MS pipes heavy grade with all fittings laid in floors or fixed to walls and ceilings etc of size 80 mm bore including cutting, inserting all as specified and directed .

Taking out old unserviceable MS pipe and supply and lay MS pipes heavy grade with all fittings laid in floors or fixed to walls and ceilings etc of size 50 mm boreincluding cutting, inserting all as specified and directed .

M&L in repair gun metal gate valve with ISI mark and iron wheel head screwed in both ends for GI pipes including taking out unserviceable for the size of 50mm including taking down old UNSV all as specified.

M&L for making connection of MS pipe of 80mm bore by providing and fixing of MS pipe including cutting and welding joint complete all as specified and directed

M&L for making connection of MS pipe of 50mm bore by providing and fixing of MS pipe including cutting and welding joint complete all as specified and directed .Note :- Tenderer may note that amount of credit will be deducted from the total amount arrived, at the time of Acceptance of contract

sunder and company

VIJAY ENTERPRISES