PROVISION OF 02 NOS WEATHER PROOF SHED FOR FUEL DISPENSER UNITS FOR ICGS JAKHAU

Amount

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out hard and dence soil complete all as specified and as directed by EIC.

M&L for PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation, filling and mass concrete etc all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed by EIC.

Removing excavated material exc. 1.50 km but n exc. 5 km and depositing soil where directed, etc complete all as specified and directed.

M&L for precast cement concrete block masonry with solid blocks of concrete (1:5:8) using 20mm graded aggregate, exc 10 cm in width and setting in cement mortar 1:6. compete all as specified and directed.

M&L for concrete in cast in situ type B1, 1:2:4 (using 20 mm graded stone aggregate) as in coping and similar work including form work complete all as specifed and directed.

M&L 15mm thick rendering in cement mortar 1:6 on fair faces of brick or concrete surface,etc completed all as specified.

M&L preparing new surface and applying two coat of white wash on wall etc complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface, completed all as specified as directed.

M&L for cement concrete 1:2:4 type B1 (using 20mm graded agg) for columns, pillars, piers, posts and struts complete all as specified and directed.

S & F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 etc complete all as spd and directed.

S & F MS plates (plain or chequered), square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment, Fe 410-W (Gde-E-250) quality-A,etc with ornamental and intricate design complete all as spd and directed.

S & F mild steel bolts purpose made exc 30cm long, diameter of neck is exc 12mm but n exc 20 mm with hexagonal or square head at one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut etc complete all as spd and directed.

S & F Pre- painted galvalume aluminum zinc coating GI based (PPGL type) corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as spd and directed. Make - JSW Colouron+/ Tata Bluescope Steel/ Lloyd Insulation as approved by AGE(I).

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridge , fixed with self tapping screws as specified etc complete all as specified. Make - JSW Colouron+/ Tata Bluescope Steel/ Lloyd Insulation as approved by AGE(I).

M&L for preparation of new steel surfaces over 10 cm in width or girth not otherwise described and applying two coats of aluminium paint over and including one coat aluminium red oxide primer complete all as spd and directed.

M & L for Mild steel CRS bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc complete all as spd and directed.

M & L for Mild steel CRS bars 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders or securing with clips etc complete all as spd and directed.

M&L for formwork to flat side concrete bases of column rough finished surface of concrete complete all as specified and as directed by Engineer-in-Charge.

M&L for RCC Nominal mix type B-I, 1:2:4 (20mm graded Aggregate) for columns in ground floor complete all as specified and as directed by Engineer-in-Charge.

S&F structural steel angle iron as posts and struts in chain link fencing posts including cutting tops to shape as directed, drilling holes, notching for wire, etc flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riverting, etc, and similar work conforming to Fe-410 Gde E-250 Quality A complete all as specified and directed.

S&F mild steel flat iron of size 40mm x 6mm for securring chain link fencing etc. in available length complete conforming to Fe-290 (Gde E-165) complete all as specified and directed.

M&L for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe-290 (Gde E-165) complete all as specified and directed.

M&L for preparation of new steel surface exc 10 cm in width or girth and applying two coats synthetic enamals paint over and inlcluding one coat of red oxide/zinc chrome primer complete, all as specified as directed.

S&F chain link fencing of 50x50mm mesh made out of 4mm thick GI wire 1mm thick PVC coating streched and fixed to fencing post all as specified and directed complete all as specified and direceted by Engr-in-Charge.

Laxmi Enterprise

NEELKANTHA ASSOCIATE

Venus Engineering

THOMAS M. MATTACKAL

S and G Construction

baghela construction

Hari Construction

SHREE MOMAY CONSTRUCTION