COMPREHENSIVE MAINTENANCE OF B/R AND E/M INCLUSIVE WELCOME MAINT AT 308 TRU AT AF STN BHUJ

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engr-in-Charge.

per thimbles,glands,earthing wire are deemed to be considered in this item. 2.Minimum One electrician to be present daily during the contract period,if found absent Rs-600 per day will be deducted daily.

Supply & fix in replacement energy saving, evironment friendly, long life, corrosion resistent, impact proof, Mini LED building security light made up of pressure die cast housing with prismatic polycarbonate diffuser and individual LEDs with secondary optics and IP 65 protection with LED 20 W light source including material and labour for suitable bracket made of 20 mm dia light grade GI pipe & MS clamps complete with nuts and bolts and washers complete all as specified and directed by Engineer-in-Charge.

Removing building materials etc (other than spoil payable under item No 03028 to 03031 in Section 3 earthwork of SSR Part II) to a distance exceeding 1.0 Km but not exceeding 1.5 Km beyond the lead included in the rates, incluing loaing, unloaing and stacking at the destination complete all as specified and directed by Engineer-in-charge. (Note one metric tonne shall mean one load Refer preamble of SSR item No 21055) .

Taking down cement plaster on brick or stone walls or PCC block walling or RCC surface, ceiling including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed by Engineer-in-charge.

Material & labour for 5 mm thick rendering on repaired or fair faces of concrete surfaces on ceiling in CM 1:3 for fair finished surfaces complete all as specified and directed by Engr-in-Charge.

Supply only water proofing compound complete all as specified and directed by Engineer-in-charge.

Material & labour for preparing new plastered ceiling/soffits of chajjas surfaces and applying three coats of white wash complete all as specified and directed by Engineer-in-Charge

Material & labour for preparation of old treated surfaces of wall including brooming down, scrapping down smoke soots etc. and appying one coat of white wash complete all as specified and directed by Engineer-in-charge. .

Material & labour for preparation of old treated surfaces on ceiling including brooming down, scrapping down smoke soots etc. and appying one coat of white wash complete all as specified and directed by Engineer-in-charge. .

Material & labour for preparation of old treated surfaces of wall surfaces and applying one coat of distemper with distemper oil emulsion white or tinted complete all as specified and directed by Engr-in-Charge.

Material & labour for preparation of old treated surfaces on ceiling and applying one coat of distemper with distemper oil emulsion white or tinted complete all as specified and directed by Engr-in-Charge.

Material & labour for preparation of old treat wall surfaces including brooming down and applying one coats of exterior emulsion paint complete all as specified and directed by Engineer-in-Charge

Material & labour for preparation of old wooden painted surfaces of any description exc 10 cm width or girth and appying one coat of synthetic enamel paint complete all as specified and directed by Engr-in-Charge.

Taking up on down steel tubing and connection incl cleaning for refining complete all as specified and directed by Engineer-in-Charge of the following bore of pipe

15mm bore

20mm bore

Supply & fix CPVC pipes ISI marked, IS-15778 with all fittings for hot and cold water, fixed with solvent cement complete to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge of following sizes: (SDR-13.5)

15mm bore

20mm bore

Dismantling of cast iron, PVC or reinforced concrete pipes jointed in cement mortar and taking out of trenches, if required complete all as specified and directed by Engineer-in-Charge of following sizes:-

100/110mm bore

75mm bore

Supply & fix PVC ultra drain,SelFit pipes, single socketed, ISI marked, IS-13592 type 'B' in any length, jointed with solvent cement fixed in walls and floors complete all as specified and directed by Engineer-in-Charge of following sizes:-

110mm bore

75mm bore

Supply & fix PVC junction single 'Tee' equal with door opening, ISI marked, IS-14735, jointed with solvent cement complete all as specified and directed by Engineer-in-Charge of following sizes:-

110mm bore

75mm bore

Supply & fix PVC sockets equal, ISI marked, IS-14735, jointed with solvent cement complete all as specified and directed by Engineer-in-Charge of following sizes:-

110mm bore

75mm bore

Taking down and refixing in same opening after any type of alteration of shutters of any description of exc 1.0 Sqm but not exc 2.0 Sqm each complete all as specified and directed by Engineer-in-charge.

EACH LEAF

Taking down aluminium door/window shutter carefully from frames for servicing/including easing adjusting replacement of damaged rubber bearing tighteneing of joints etc complete and make it in functional state complete all as specified and directed by Engineer-in-Charge.

Supply only aluminium anodised grill of approved shape with opening in grill 66mm x 80mm (diagonally) or nearest to + 5mm made out of standard aluminium moulded section of size 6mm x 7mm complete all as specified and directed by Engineer-in-charge. .

Hacking out old broken glass (any thickness, size, quality or description) from wooden /steel frames or stone , concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed by Engineer-in-charge.

Material & labour for 4.00 mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.50 Sqm in each pane complete all as specified and directed by Engineer-in-charge. .

Material & labour for aluminium window with double side hung shutter for glazing and gauging and frame with one or more rebates anodised aluminium section including section for fixing of aluminium grills with suitable fixtures, jointing cleats for fixing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium beading screws, type B20 100mm long suitable handle and anodised aluminum fittings such as stay, hinges glazing with 5 mm thick tinted sheet glass and gauging with aluminium wire cloth of size 0.45mm dia of wire and 1.40mm aperture as per drg No. CEAA/TD/133 sheet No. 1/2 and 2/2 dated 13.12.02 except fixed glazing (FG) complete all as specified and directed by Engineer-in-charge.(Tint of glass shall be approved by GE) Note :- Aluminium grill fixed under above item shall be measured and paid separately . .

QUINTAL

Dismantling of wall and ceiling boards (fibre, pulb, insulation etc or insulation boards /slabs / blankets any thickness including cover fillets complete all as specified and directed by Engineer-in-charge.

Supply , fabrication & fix anodised (15 micron) aluminium sliding windows/ ventilators aluminium

sections as in frames , sliding/ fixed shutters etc. With one or more rebates incl. Jointing cleats & locking arrangements complete all as specified & as per manufacturer's instruction complete all as specified and directed by Engineer-in-charge. Note- Quoted rate shall deemed to be included for supply of aluminium sections, fabricate & fixing in position of window frames & shutters, locking arrangements . .

Supply & fix rubber beading for fixing of glass of item No 101 below complete all as specified and directed by Engineer-in-charge. .

Material & labour for 12 mm thick peformated particle board / tiles for insulation and accoustic purpose 60x60 cm in size fixed with nails to timber frame work or with staples on snap grid complete all as specified and directed by Engineer-in-charge.

Removing of old water proofing treatment including screed bed and cleaning the surface of slab with wire brushes removing dust, foreign materials including flushing at junction of wall and removing the rubbish off the premises to a distance exc. 500m complete all as specified and directed by Engineer-in-charge. .

Supply & fix in repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-charge.

Material & labour for PCC 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in roof kerbs/coping/ bed block / depression complete all as specified and directed by Engineer-in-charge.

Material & labour for water proofing treatment on roof and preparing the surfaces to receive WPT treatment , applying cold bituminous primer @ 0.30 ltr / Sqm conforming to IS 3384 applied on plastered surfaces including side walls , followed by a layers of APP based polymeric membrane reinforced with polyster non woven fabric (weighing 3.5 Kg/Sqm(minimum) and 3 mm thick) with mineral finish laid on primed surface by torch application with side overlap 100 mm and ends over laps 150 mm , joints sealed properly as per manufacturers instructions complete all as specified and directed by Engineer-in-charge. .

Material & labour for providing cement concrete type B-0, 1:2:4 (using 12.5mm graded stone aggregate) as in roof kerbs, mud stops, filling in frames and the like rounded or or chamfered on edges complete all as specified and directed by Engineer-in-charge. .

Material & labour for 75 mm thick cement concrete type C-2 (1:3:6) using 40 mm graded stone aggregate as in sub base under interlocking tiles complete all as specified and directed by Engineer-in-charge. .

Material & labour for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade complete all as specified and directed by Engineer-in-charge. .

Dismanteling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed by Engineer-in-charge.

Material & labour for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-charge.

Material & labour for rolled sections as in framing for cladding, glazing, roofing and the like fixed with angle cleats and connecting plates, etc complete all as specified and directed by Engineer-in-charge.

Material & labour for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete complete all as specified and directed by Engineer-in-Charge.

Material & labour for kota stone slab 20-25mm thick in riser of steps, skiting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs 25mm bore stainless steel heavy duty draphery rods (curtain rod) including all fittings and fixers cut to length and fix in position including decorative type fimals (bracket) colored finish of approved pattern complete all as specified and directed by Engineer-in-Charge.

Pulling down the existing U/S wires of any type from concealed wiring carefully of aluminium/copper point wiring (light, fan, bell, socket, power point etc.) with or without conduit, along with all connected accessories such as ceiling rose, switches, sockets, switch boards, fan regulator etc complete all as specified and as directed by the Engr-in-Charge

POINT

Pulling out sub main wiring only any size of aluminium conductor cable PVC insulated with or without condiut complete all as specified and as directed by the Engr-in-Charge

Material & labour for point wiring complete with 1.5 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 volts grade ISI marked drawn through and including PVC CASING & CAPPING INCLUDING accessories etc including fixed to wall/ceiling including provision of 1.5 sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed as earth wire continuity with PVC surface box complete all as specified and directed by Engineer-in-Charge for :-

One light point controlled by one, one way switch single pole piano type.

One Fan point controlled by one, one way switch single pole piano type.

One 3 pin 5 Amp socket outlet on the same board.

(f) After 2 to 3 days, sunken portion must be overlaid with a 50 mm avg thick concrete screed M 15 type B0 mixed with intergral WPC (Liquid) laid to slope 1:60 towards outer face of wall. Provide 40 mm under dia UPVC pipe at the lowest point with 300 mm projection beyond the outer face of the wall. Then fill up the sunken portion with lean concrete 1:5:10 type E2. (g) After completing plumbing work in the toilet/WC/Bath/Kitchen floor, tiling work (floor and dado) can be carried out using suitable Tile Adhesives and ready

One 3 pin 5 Amps socket out let on independent board.

Pulling out sub main wiring only any size of aluminium conductor cable PVC insulated with or without condiut complete all as specified and as directed by the Engr-in-Charge

Material & labour for point wiring complete with 1.5 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 volts grade ISI marked drawn through and including PVC CASING & CAPPING INCLUDING accessories etc including fixed to wall/ceiling including provision of 1.5 sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed as earth wire continuity with PVC surface box complete all as specified and directed by Engineer-in-Charge for :-

One light point controlled by one, one way switch single pole piano type.

One Fan point controlled by one, one way switch single pole piano type.

One bell point controlled by one bell push on independent board.

Material & labour for framed work as in grills, guard bars, doors or gates of angle, duct frame or other section with gusset plates rails brases etc completed drilled for fixing of steel sheeting or other covering Doorsetc to be prepared for hanging or sliding with and including either hook and hinges or steel hanging and door fitting (exclusive of steel sheeting or other covering) and hanging also fasteningand fixed confirming to Fe 410W or (Gde E-250 Quality) complete all as specified and directed by Engineer-in-charge. .

Material & labour for point wiring complete with 1.5 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 volts grade ISI marked drawn through existing conduit including provn of 1.5 sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed as earth wire continuity with new plastic laminated white coloured top sheet cover 3.0 mm thick on existing sunken box complete all as specified and directed by Engineer-in-Charge for :-

One bell point controlled by one bell push.

Demolition of cement concrete (unreinforced) of any description and any position not otherwise specifically provided for complete all as specified and directed by Engineer-in-charge. .

Supply & fixing in replacement of water heater storage type 25 Ltr, Ratted wattage 2000W, voltage 230V AC, frequency 50Hz phase single auto cutoff, rust proof external body suitable for highrise building suitable for water pressure head upto 8 bars star rating (BEE) complete all as specified and directed by Engineer-in-Charge ( Note: Old unserviceable water heater will be deposited in MES store yard).

Material & labour for sub main wiring with two runs of PVC insulated and unsheathed FRLSH cable 650/1100 Volts grade, conforming to IS-1536-1977 multi-stranded 4 Sqmm single core, copper conductor drawn through and including PVC casing caping ISI marked with accessories and 4 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 volts grade, ISI marked as earth continuity wire complete all as specified and directed by Engr-in-Charge. (Note: Two runs of conductor with one run of earth wire and PVC casing capping will be measured & paid as one unit)

Material & labour for sub main wiring with two runs of PVC insulated and unsheathed FRLSH cable 650/1100 Volts grade, conforming to IS-1536-1977 multi-stranded 6 Sqmm single core, copper conductor drawn through and including PVC casing caping ISI marked with accessories and 6 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 volts grade, ISI marked as earth continuity wire complete all as specified and directed by Engr-in-Charge. (Note: Two runs of conductor with one run of earth wire and PVC casing capping will be measured & paid as one unit)

Supply and fixing in repairs wall mounted decorative ultra slim LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack instant start with uniform light distribution 10 W 2 ft indoor decorative with 2 Core copper wire from ceiling rose to light fitting etc complete all as specified and directed by Engr-in-Charge

Supply and fixing in repairs wall mounted decorative ultra slim LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack instant start with uniform light distribution 18/20 W 4 ft indoor decorative with 2 Core copper wire from ceiling rose to light fitting etc complete all as specified and directed by Engr-in-Charge

Supply & fixing in replacement of LED Lamp, 7 W ,Type of cap B22, wide operating range 140V -280V, Input current 08mA- 30mA, lumen 180-300, UV and IR free light, color temperature 6500K, cool day light, up to 80 % energy saving over GLS complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement double door Sheet metal enclosures factory made DBs protection class IP-43, suitable for fixing of MCBs, Isolators etc, confirming to IS 13032 triple pole and neutral 4 ways with 200 Amp rated bus bar 415 volts powder coated complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement double door Sheet metal enclosures factory made DBs protection class IP-43, suitable for fixing of MCBs, Isolators etc, confirming to IS 13032 single pole and neutral 12 ways with 200 Amp rated bus bar 415 volts powder coated complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement double door Sheet metal enclosures factory made DBs protection class IP-43, suitable for fixing of MCBs, Isolators etc, confirming to IS 13032 single pole and neutral 8 ways with 200 Amp rated bus bar 415 volts powder coated complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement double door Sheet metal enclosures factory made DBs protection class IP-43, suitable for fixing of MCBs, Isolators etc, confirming to IS 13032 single pole and neutral 4 ways 415 volts powder coated complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement of isolators/MCBs, etc. In distribution board of the following rating and capacities complete all as specified and directed by Engineer-in-Charge of following :-

MCB TPN 415 volts 63 Amps Capacity, 10 KA

MCB SPN of 240 volts 20/32/40 Amps Capacity, 'C' series, 10 KA

MCB SP of 240 volts 5-40 Amps Capacity, 'C' series, 10 KA

Taking down and refixing ceiling fans/exhaust fan of any sweep any size from site for repair complete all as specified and directed by Engineer-in-charge.

EACH JOB

Material & labour for 15mm thick rendering in cement mortar 1: 4 on faces of brick work or concrete surfaces with WPC, finished even and smooth without using extra cement as in roof complete all as specified and directed by Engineer-in-charge. Note:- WPC shall be measured and paid separately .

Material & labour for taking out & removing old burnt-out windings of ceiling fans of any description and rewinding of fan motor with appropriate size super enameled copper wire as approved by Eng-in-charge including insulating material such as illuminous paper,Letherized paper,cotton tape,glass sleeving,insulating varnish ,Bearing ,Bushes,capacitor etc.and transportation to site after testing at workshop,connecting and testing on full load to the entire satisfaction of Eng-in-charge,including painting of fans of any description(ceiling fan/exhaust fan/wall mounte fan/pedestal fan) with applying one coat of synthetic enamel paint(white/Grey) by spray machine including preparation of exisiting decorated surfaces of fans complete all as specified and directed by Engineer-in-charge.

Material & labour for servicing of 1200/1400MM ceiling fan by dismantling carefully and taking out unserviceable parts, dust & grease, cleaning of internal parts with kerosene oil, washing, checking of alignment of shaft, oiling and re-greasing of bearing/bushes including replacing of unserviceable part like bearing ,gu

n metal bush, capacitor,Rubber reel of suitable capacity and re-assembling the same and complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement of PVC body exhaust fan, AC single phase 230/240V of size 250 mm sweep with louvers including making hole of suitable size/ alteration to the existing hole to fix the Exhaust fan complete all as specified and directed by Engineer-in-charge. (Note: Old unserviceable Exhaust Fan will be deposited in MES store yard).

Supply & fix in replacement of PVC body exhaust fan, AC single phase 230/240V of size 300 mm sweep with louvers including making hole of suitable size/ alteration to the existing hole to fix the Exhaust fan complete all as specified and directed by Engineer-in-charge. (Note: Old unserviceable Exhaust Fan will be deposited in MES store yard). .

Supply & fix in replacement of metal body exhaust fan, AC single phase 230/240V of size 300 mm sweep with louvers including making hole of suitable size/ alteration to the existing hole to fix the Exhaust fan complete all as specified and directed by Engineer-in-charge. (Note: Old unserviceable Exhaust Fan will be deposited in MES store yard). .

Supply & fix in replacement, switch piano type, 5 Amp. SP, one way complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement socket outlet 3 pin, 5A, flush complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement switch socket combination, 2 in 1, 5 Amp, flush type complete all as specified and directed by Engineer-in-charge. .

Supply & fix in replacement switch socket combination 2 in 1, 5/16A 5 in 1 Amp flush type universal complete all as specified and directed by Engr-in-Charge. .

Supply & fix in replacement switch bell push, flush type, 5 Amp complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement bell, AC, 230 V, SP, ding dong type complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement stepped type electronic fan regulator flush type on the existing phenolic laminated etc as reqd single pole 240 volts grade 350 watts heavy duty ISI marked complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement metal clad enclosure pole and neutral with a two pin and earth plug and socket complete 240 volt with one single pole MCB of 20 Amps complete all as specified and as directed by Engineer-in-Charge

Labour only for attending emergent complaints i.e no light ,earth leakage,short circuit,neutral break,mains/submain/internal circuit of existing system of main building/block,making continious electric supply including carrying out minor repairs etc as required to make the system in order/functional including replacing fuse wire,copper cable,copper thimbles,glands,earthing wire complete all as specified and directed by Engineer-in-Charge. Note:- 1.Rate of Fuse wire,copper cable of size 1.5,2.5,4 Sqmm upto 3 RM,cop

Supply & fix in replacement lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement of ceiling rose 3 phase, PVC/ Polycarbonate body complete all as specified and directed by Engr-in-Charge.

Supply & fix modular plastic surface box of module 1/2 flush ISI marked complete all as specified and directed by Engineer-in-Charge.

Supply & fix modular white cover plate with frame of module 1 flush ISI marked complete all as specified and directed by Engineer-in-Charge.

Supply & fix modular white cover plate with frame of module 2 flush ISI marked complete all as specified and directed by Engineer-in-Charge.

Supply & fix modular white cover plate with frame of module 3 flush ISI marked complete all as specified and directed by Engineer-in-Charge.

Supply & fix modular white cover plate with frame of module 4 flush ISI marked complete all as specified and directed by Engineer-in-Charge.

Supply & fix modular white cover plate with frame of module 6 flush ISI marked complete all as specified and directed by Engineer-in-Charge.

Supply & fix modular white cover plate with frame of module 8 flush ISI marked complete all as specified and directed by Engineer-in-Charge.

Supply & fix modular blank plate module 1 complete all as specified and directed by Engineer-in-Charge.

Supply & fix in replacement modular switch flush type SP one way, 6 Amp, 1 module ISI Mark complete all as specified and as directed by the Engr-in-Charge

Supply & fix in replacement modular socket outlet 3 pin,6 Amp, flush type 2 module, ISI marked complete all as specified and as directed by the Engr-in-Charge

Supply & fix in replacement modular swicth, 16 Amp flush type 1 module complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement modular socket outlet, 3 pin, 6/16 Amp flush type 2 module complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement modular bell push, flush type, 6 Amp,1 module complete all as specified and directed by Engr-in-Charge.

Supply & fix in replacement of ceiling fan regulator 120 Watt 2 module Modular type electronic step type 5 step 360 deg complete all as specified and directed by Engr-in-Charge.

Supply and repair hylum sheet 3mm thick as existed in the switch board making provision for fixing switches and socket complete all as specified and directed by Engr-in-Charge.

Material & labour for disconneting electrically and mechanically the existing geyser of any description,any capacity and make/type and in any position for repair/replacement/painting/cleaning etc including disconneting existing cold and hot water pipe connections, strip opening of geyser for descaling of tank element, thermostate,inlet/outlet water pipe connection etc using suitable chemical/wire brush,replacement of unserviceabe parts, re-assembling the same after,repair/descaling, fixing in position including, connecting inlet/outlet water pipe connection, electrical connections any testing of geyser complete all as specified and directed by Engineer-in-charge.

Material & labour for special treatment to sunken portion with (a) Clean the sunken portion of toilet/Bath/WC/Kitchen throughly to remove laitance, dirt, dust, etc. (b) Form angle fillet of size 40 mm x 40 mm along the junction of wall and floor using polymer modified mortar (c) Sanitary pipes entering through walls and floor shall be sealed with and the gaps to be grouted with non-shrink cementitous grout Bathseal Grout" or eqvt. Nahani traps, etc to be fitted securely and the gaps around it to be grouted in the same manner. (d) Apply one coat of a Bitumen-modified polymer coating on all angle fillets by brush and cover it with 100 mm open woven mesh when it is still wet. Apply second coat of the same coating on the angle fillets and allow it to dry completely. (e) In the remaining area, in dry sustrate condition brush apply first coat of the same coating and further apply second coat when first coat is dry. Extend the coating upto 150 mm above the FFL. Above FFL, another cementitious waterproof coating "Dr Fixit Pidifin 2 K" or eqvt can be further applied right upto 2.1 mm to waterproof the shower area also, it is a bathroom or bath cubicles of a sanitary annex and apply second coat after 6-8 hours and allow to dry completely. .

Supply & fix in replacement metal plug top 20Amps 3 pin complete all as specified and directed by Engineer-in-charge. .

Supply & fix in replacement 2.0 KW electric heating element at site including rubber ring washers ISI marked complete all as specified and directed by Engineer-in-charge.

Supply & fix in replacement for PVC connection with brass nipple 15 mm x 450 mm long for geyser 25/50 ltrs capacity as per sample complete all as specified and directed by Engineer-in-charge.

Supply & fixing in replacement tamper proof single phase AC KWH meter 10-60 Amps with following features including sealing and sealing wire, class – 1 accuracy as per IS 13779, 240V, 50HZ LCD display, forward energy recording irrespective of current direction, LED indication for earth leakage, elegant polycarbonate enclosure high surge with stand up to 8 KV anti temper feature. measures & displays kWh complete all as specified and as directed by Engineer-in-Charge. ( Note: Old unserviceable elect meter will be deposited in MES store yard).