TENDER ENQUIRY FOR NORMAL REFIT OD TUG-BALDEV

HULL SOW TUG BALDEV Equipment/Defect Description 001 Docking- Vessel to be docked in both versions. Note 1:- Firms not to quote view docking, undocking and dock blocks preparation will be done by Navy and the job is required to be carried out in Navy Premises (i.e ND(V) slipway).Note 2:- Last Undock -Aug 18

002 Hull Cleaning Under Water and Boot Top Area (a) HP jet clean entire under water area and boot top area (with a pressure not exceeding 3000 PSI) including ship side and remove the marine growth/barnacles and present for survey.

002 Hull Cleaning Shipside above water (b) HP jet clean entire Shipside (with a pressure not exceeding 3000 PSI) to remove the salts and contaminants from the surface and present for survey and present for survey.

002 Hull Cleaning Superstructure (c) HP jet clean entire Superstructure (with a pressure not exceeding 3000 PSI) including ship side and remove salts and contaminants from the surface and present for survey.

002 Hull Cleaning Weather Deck (d) HP jet clean entire Weather Deck (with a pressure not exceeding 3000 PSI) remove salts and contaminants from the surface and present for survey.

002 Hull Cleaning Fresh Water Gravity Tanks (e) Manually clean two in no. Fresh water gravity tank and present for survey.The tanks should be washed out with fresh water and soap water to remoeve any sediment or dirt present in the tank

002 Hull Cleaning Fresh Water Tanks (f) Manually clean two in no. Fresh water gravity tank and present for survey.The tanks should be washed out with fresh water and soap water to remoeve any sediment or dirt present in the tank

002 Hull Cleaning Foam tank (g) Manually clean fire fighting foam tank and present for survey. The tanks should be washed out with fresh water and soap water to remoeve any sediment or dirt present in the tank

002 Hull Cleaning Ballast Tanks (h) Manually clean two in no. Ballast tanks and present for survey. The tanks should be washed out with fresh water and soap water to remoeve any sediment or dirt present in the tank

002 Hull Cleaning Cable locker (j) Manually clean Cable locker and present for survey. The tanks should be washed out with fresh water and soap water to remoeve any sediment or dirt present in the tank

002 Hull Cleaning Fore Peak Tanks, Void Space and Cofferdam (k) Manually clean two in no. Fore peak tanks, one each void space & cofferdam and present for survey.The tanks should be washed out with fresh water and soap water to remove any sediment or dirt present in the tank

002 Hull Cleaning Machinery compartments (l) Manually clean bilges and bulkheads of engine room using detergent solution to remove oil, grease and other contaminantsand present for survey (i) Engine room (Bilges: 150 Sqm, Bulkheads:200 Sqm)

002 Hull Cleaning Machinery compartments (m) Manually clean bilges and bulkheads of SRP Compt using detergent solution to remove oil, grease and other contaminant and present for survey (i) SRP compt.

002 Hull Cleaning Fuel Tanks (n) Manually clean two in no. Fuel tanks with fresh water and soap water to remove any sediment or dirt present in the tank

002 Hull Cleaning RU Tanks (p) Manually clean two in no. RU tanks with fresh water and soap water to remove any sediment or dirt present in the tank and present for survey

002 Hull Cleaning Lube oil tanks and dirty oil tanks (q) Manually clean two in no. Lube oil tanks and dirty oil tanks with fresh water and soap water to remoeve any sediment or dirt present in the tank and present for survey

003 Hull survey External and Internal Hull survey. Carry out visual and hammer survey (in the presence of QC representatives) in accordance with NO 01/15 of under water hull, boot top area, above water hull, super structure, weather decks and all internal compartments(i.e. FW tanks, ballast tanks, fore peak tank, engine room, steering compartment, FO tanks, cofferdams, all stiffeners and deck fittings etc.. Approx. area:1500 Sqm Firm to submit 07 copies of Hull survey report .

004 UTG Survey Carry out UTG survey in thge presence of QC representatives of U/W hull, ship side, superstrcture, weather deck, bulkheads, Tanks, living spaces covering entire part of hull. Firm to submit 07 copies of Hull survey report.

005 Steel Renewals Quote for steel renewal at various locations as per survey report. Note 1:- Quoted repair cost shall include cost of both sides blasted and primed Grade `A’ quality ship building steel for shell and IS 2062 Grade `B’ quality steel for non structural works, degutting/regutting/ renewal of all obstructions in way of steel renewals including lagging/panelling, minor fittings/ equipments with their foundations, ventilation systems, staging etc., as indicated by survey team / RMT, proving of the weld runs by non-destructive tests and by hose test on completion of welding, pressure testing and proving of tanks where steel renewal undertaken etc. Note 2:- Firms to indicate cost of new panelling(2mm thick) and Lagging (2" MFMB) material in the budgetary cost for 50 sqm each.

006 Build ups Carry out build ups as indicated by the Hull survey team/ Surveyor (a) 25 x 25 mm - 150Nos

006 Build ups Carry out build ups as indicated by the Hull survey team/ Surveyor (b) 50 x50 mm - 75 Nos

007 Fairing Carryout fairing of deformed structures as indicated by Hull Survey Team/ Surveyor

008 Re-welding run Carry out re-welding runs on weld seams as indicated by Hull survey team/ QC/ RMT.

009 Sea tubes (a) Grit blasting of the sea tubes to be carried out for survey and pressure testing of sea tube including sea chest . Dia - 300mm

009 Sea tubes (b) Carryout renewal of defective seatubes, OD-300mm, schedule 80.

010 Draught Marks Draught marks, both Roman and Numeric, corroded/eaten away. To be renewed and painted.

011 Sacrificial Anodes (a) Renew MK - I sacrificial anodes which are perished by over 50%. Note:- Anodes will be supplied by Navy/COY.

011 Sacrificial Anodes (b) Renew MK - V sacrificial anodes which are perished by over 50%. Note:- Anodes will be supplied by Navy/COY.

012 Surface preparation Under Water area including Boot top area with Grit Blasting (a) Spot blasting to SA 2.5 on paint damaged areas/ renewed plate areas as per the paint OEM rep recommendation for paint application.

012 Surface preparation Under Water area including Boot top area with Sweep Blasting (b) Sweep blasting to SA 1 on the rest of the underwater areas for removal of anti-fouling and applicationof tie coat and 03 coats of anti-fouling.

013 Painting - Jotun Scheme Under Water area including Boot top area Paint under water area with following paint scheme as per OEM recommendations:- Note:- Quoted repair cost shall be inclusive of cost of paints also. (a) 1st Coat: Primer - penguard primer - 50 microns

013 Painting - Jotun Scheme Under Water area including Boot top area Paint under water area with following paint scheme as per OEM recommendations:- Note:- Quoted repair cost shall be inclusive of cost of paints also. (b) 2nd Coat: Anti Corrosive - Jotacote Universal (Aluminium) - 150 microns

013 Painting - Jotun Scheme Under Water area including Boot top area Paint under water area with following paint scheme as per OEM recommendations:- Note:- Quoted repair cost shall be inclusive of cost of paints also. (c) 3rd Coat: Anti Corrosive - Jotacote Universal (grey) - 150 microns

013 Painting - Jotun Scheme Under Water area including Boot top area Paint under water area with following paint scheme as per OEM recommendations:- Note:- Quoted repair cost shall be inclusive of cost of paints also. (d) 4th Coat: Tie Coat: Safeguard ES - 125 microns

013 Painting - Jotun Scheme Under Water area including Boot top area Paint under water area with following paint scheme as per OEM recommendations:- Note:- Quoted repair cost shall be inclusive of cost of paints also. (e) 5th Coat: A/F: Seaquantum Ultra(Brown/Light Red) - 150 microns

013 Painting - Jotun Scheme Under Water area including Boot top area Paint under water area with following paint scheme as per OEM recommendations:- Note:- Quoted repair cost shall be inclusive of cost of paints also. (f) 6th Coat: A/F: Seaquantum Ultra(Red Brown/Dark Red) - 150 microns

013 Painting - Jotun Scheme Under Water area including Boot top area Paint under water area with following paint scheme as per OEM recommendations:- Note:- Quoted repair cost shall be inclusive of cost of paints also. (g) 7th Coat: A/F: Seaquantum Ultra(Brown/Light Red/ Black) - 150 microns

013 Painting - Jotun Scheme Under Water area including Boot top area Paint under water area with following paint scheme as per OEM recommendations:- Note:- Quoted repair cost shall be inclusive of cost of paints also. (g) 8th Coat: A/F: Seaquantum Ultra(Brown/Light Red/ Black) - 150 microns

014 Surface Preparation Above Water Area and Bulwark (a) Spot blasting to SA 2.5 on paint damaged areas/ renewed plate areas as per the paint OEM rep recommendation for paint application.

014 Surface Preparation Above Water Area and Bulwark (b) Sweep blasting to SA 1 on the rest of above water area for paint application as recommended by paint OEM.

015 Painting - JOTUN Scheme. Above Water Area and Bulwark Paint above water area with following paint scheme as per OEM recommendations:- Note:- Quoted repair cost shall be inclusive of cost of paints also. (a) 1st Coat: Penguard primer - 50 microns DFT

015 Painting - JOTUN Scheme. Above Water Area and Bulwark Paint above water area with following paint scheme as per OEM recommendations:- Note:- Quoted repair cost shall be inclusive of cost of paints also. (b) 2nd Coat: Jotamastic(Grey/ Red Brown) - 125 microns DFT

015 Painting - JOTUN Scheme. Above Water Area and Bulwark Paint above water area with following paint scheme as per OEM recommendations:- Note:- Quoted repair cost shall be inclusive of cost of paints also. (c) 3rd Coat: Jotamastic(Grey) - 125 microns DFT

015 Painting - JOTUN Scheme. Above Water Area and Bulwark Paint above water area with following paint scheme as per OEM recommendations:- Note:- Quoted repair cost shall be inclusive of cost of paints also. (d) 4th Coat: Hard Top XP Grey - 60 microns DFT

016 Surface Preparation Super Structure and Deck Fittings . (a) Carry out mechanical cleaning to ST3 standard as per survey report of Paint OEM for paint application.

016 Surface Preparation Super Structure and Deck Fittings. (b) Carry out mechanical cleaning to ST 1 standard as per survey report of Paint OEM for paint application.

017 Painting - JOTUN Scheme Super Structure and Deck Fittings. Paint super structure area area with following paint scheme as per OEM recommendations:- Note:- Quoted repair cost shall be inclusive of cost of paints also. (a) 1st Coat: primer - penguard primer -50 microns DFT

017 Painting - JOTUN Scheme Super Structure and Deck Fittings. Paint super structure area area with following paint scheme as per OEM recommendations:- Note:- Quoted repair cost shall be inclusive of cost of paints also. (b) 2nd Coat: Jotamastic 80 red brown - 125 microns DFT

017 Painting - JOTUN Scheme Super Structure and Deck Fittings. Paint super structure area area with following paint scheme as per OEM recommendations:- Note:- Quoted repair cost shall be inclusive of cost of paints also. (c) 3rd Coat: Jotamastic 80 grey- 125 microns DFT

017 Painting - JOTUN Scheme Super Structure and Deck Fittings. Paint super structure area area with following paint scheme as per OEM recommendations:- Note:- Quoted repair cost shall be inclusive of cost of paints also. (d) 4th Coat: Hard Top GREY 7040- 150 microns DFT

018 Surface Preparation Weather Decks Bridge Deck Bridge Top and Fittings (a) Carry out surface preperation to WJ 2.0 standard by using Hydro Jet Blasting for paint application for entire weather deck, wheel house deck, flag deck and life raft deck.

019 Painting - JOTUN Scheme Weather Decks Bridge Deck Bridge Top and Fittings Paint weather decks and fittings with following paint scheme:- Note:- Quoted repair cost shall be inclusive of cost of paints also. (a) 1st Coat: primer - Penguard Primer -50 microns DFT

019 Painting - JOTUN Scheme Weather Decks Bridge Deck Bridge Top and Fittings Paint weather decks and fittings with following paint scheme:- Note:- Quoted repair cost shall be inclusive of cost of paints also. (b) 2nd Coat: Jotamastic 87 of 200 microns

019 Painting - JOTUN Scheme Weather Decks Bridge Deck Bridge Top and Fittings Paint weather decks and fittings with following paint scheme:- Note:- Quoted repair cost shall be inclusive of cost of paints also. (c) 3rd Coat: Jota Armour Dark grey of 800 microns

020 Surface Preparation Internal Compartments Fresh Water Tanks (02 Nos) and Fire fighting foam tank:- Carry out mechanical cleaning to ST3 standard as per survey report of Paint OEM for paint application.

021 Painting - JOTUN Scheme. Fresh Water Tanks (02 Nos) and Fire fighting foam tank Paint two in no. fresh water tanks and one fire fighting foam tank with following paint scheme:- Note:- Quoted repair cost shall be inclusive of cost of paints also. (a) 1st Coat: Penguard HB (white) -100 microns DFT

021 Painting - JOTUN Scheme. Fresh Water Tanks (02 Nos) and Fire fighting foam tank Paint two in no. fresh water tanks and one fire fighting foam tank with following paint scheme:- Note:- Quoted repair cost shall be inclusive of cost of paints also. (b) 2nd Coat: Penguard HB(Grey) -100 microns DFT

021 Painting - JOTUN Scheme. Fresh Water Tanks (02 Nos) and Fire fighting foam tank Paint two in no. fresh water tanks and one fire fighting foam tank with following paint scheme:- Note:- Quoted repair cost shall be inclusive of cost of paints also. (c) 3rd Coat: Penguard HB (white) -100 microns DFT

022 Surface Preparation Tanks Fore Peak Tanks, Ballast Tanks(02 No), cable locker (a) Carry out mechanical cleaning to ST3 standard as survey report of Paint OEM for paint application.

022 Surface Preparation Tanks Fore Peak Tanks, Ballast Tanks(02 No), cable locker (b) Carry out mechanical cleaning to ST 1 standard as per survey report of Paint OEM for paint application.

023 Painting - JOTUN Scheme Fore Peak Tanks, Ballast Tanks(02 No), cable locker Paint fore peak tanks,ballast tanks (02 in no.) and cable locker with following paint scheme. Note:- Quoted repair cost shall be inclusive of cost of paints also. (a) 1st Coat: primer - Penguard Primer -50 microns DFT

023 Painting - JOTUN Scheme Fore Peak Tanks, Ballast Tanks(02 No), cable locker Paint fore peak tanks,ballast tanks (02 in no.) and cable locker with following paint scheme. Note:- Quoted repair cost shall be inclusive of cost of paints also. (b) 2nd Coat: Anticorrosive Balloxy (HB light) - 150 microns

023 Painting - JOTUN Scheme Fore Peak Tanks, Ballast Tanks(02 No), cable locker Paint fore peak tanks,ballast tanks (02 in no.) and cable locker with following paint scheme. Note:- Quoted repair cost shall be inclusive of cost of paints also. (c) 3rd Coat: Anticorrosive Balloxy (HB light) - 150 microns

024 Surface Preparation Machinery Compartments- Engine room and SRP (a) Carry out mechanical cleaning to ST 3 standard as per survey report of Paint OEM for paint application ( Bilges).

024 Surface Preparation Machinery Compartments -Engine room and SRP (b) Carry out mechanical cleaning to ST 1 standard as per survey report of Paint OEM for paint application (Bulkheads).

025 Painting - JOTUN Scheme. Machinery Bilges Paint bilges of Engine room and SRP compartment with following paint scheme.Note:- Quoted repair cost shall be inclusive of cost of paints also. (a) 1st Coat: primer - Penguard Primer -50 microns DFT

025 Painting - JOTUN Scheme. Machinery Bilges Paint bilges of Engine room and SRP compartment with following paint scheme.Note:- Quoted repair cost shall be inclusive of cost of paints also (b) 2nd Coat: Anticorrosive - Jotacote Universal (Aluminium) - 150 microns DFT

025 Painting - JOTUN Scheme. Machinery Bilges Paint Bilges of Engine room and SRP compartment with following paint scheme.Note:- Quoted repair cost shall be inclusive of cost of paints also (c) 3rd Coat: Anticorrosive - Jotacote Universal (Grey) - 150 microns

025 Painting - JOTUN Scheme. Machinery Bilges Paint bilges of Engine room and SRP compartment with following paint scheme.Note:- Quoted repair cost shall be inclusive of cost of paints also. (d) 4th Coat: Penguard Top Coat - 50 microns.

026 Surface Preparation Machinery Compartments- Bulkheads Of Engine Room And ASP (a) Carry out mechanical cleaning to ST 3 standard as per survey report of Paint OEM for paint application ( Bilges).

026 Surface Preparation Machinery Compartments- Bulkheads Of Engine Room And ASP (b) Carry out mechanical cleaning to ST 1 standard as per survey report of Paint OEM for paint application ( Bilges).

027 Painting- Jotun Scheme. Machinery Compartments Bulkheads Of Engine Room And ASP Paint bulkheads of Engine room and SRP compartments with following paint scheme Note:- Quoted repair cost shall be inclusive of cost of paints also. (a) 1st Coat: primer - Penguard Primer - 50 microns DFT

027 Painting- Jotun Scheme. Machinery Compartments Bulkheads Of Engine Room And ASP Paint bulkheads of Engine room and SRP compartments with following paint scheme:- (b) 2nd Coat: White interior fire retardant paint 100 microns DFT

027 Bulkhead Painting. Painting - Jotun Scheme. Paint bulkheads of Engine room and SRP compartments with following paint scheme:- (c) 3rd Coat: White interior fire retardant paint 100 microns DFT

028 Cleaning and Application of Oil (a) Fuel Tanks Manually scrap and clean Fuel Tank (02nos) to bare metal and apply two coats of OM 750 oil. Note:- Quoted repair cost shall be inclusive of cost of oil also

028 Cleaning and Application of Oil (b) RU (FODS) Tanks Manually scrap and clean RU Tank (02nos) to bare metal and apply two coats of OM 750 oil. Note:- Quoted repair cost shall be inclusive of cost of oil also

029 Surface Preparation Tanks LO tanks and dirty oil tanks Carry out mechanical cleaning to ST3 standard as survey report of Paint OEM for paint application.

030 Painting - JOTUN Scheme LO tanks & dirty oil tanks Paint LO tanks & dirty oil tanks with following paint scheme. (a) 1st Coat: primer - Tankguard HB-125 microns DFT Note:- Quoted repair cost shall be inclusive of cost of paints also.

030 Painting - JOTUN Scheme LO tanks & dirty oil tanks Paint LO tanks & dirty oil tanks with following paint scheme. (b) 2nd Coat: primer - Tankguard HB-125 microns DFT Note:- Quoted repair cost shall be inclusive of cost of paints also.

031 Gratings Open underwater gratings, present for survey, carry out necessary repairs and refit back.

032 Anchor and Anchor chain cable Anchor and Anchor chain cable and associated fittings are to be hydro jet blasted to bare metal, eased for free movement and to present for survey at NDV\MFAB Dept.Paint with black bituminous paint post survey IAW NO 12/2001 and refit back. Note : -The job involves removal of anchors and accessories, laying out for cleaning,painting and refitment. a) Anchor

032 Anchor and Anchor chain cable Anchor and Anchor chain cable and associated fittings are to be hydro jet blasted to bare metal, eased for free movement and to present for survey at NDV\MFAB Dept.Paint with black bituminous paint post survey IAW NO 12/2001 and refit back. Note : -The job involves removal of anchors and accessories, laying out for cleaning,painting and refitment. b) Chain cable (Dia 17.5mm) total length of the cable 275 Mtrs

032 Anchor and Anchor chain cable Anchor and Anchor chain cable and associated fittings are to be hydro jet blasted to bare metal, eased for free movement and to present for survey at NDV\MFAB Dept.Paint with black bituminous paint post survey IAW NO 12/2001 and refit back. Note : -The job involves removal of anchors and accessories, laying out for cleaning,painting and c) Swivel piece

032 Anchor and Anchor chain cable Anchor and Anchor chain cable and associated fittings are to be hydro jet blasted to bare metal, eased for free movement and to present for survey at NDV\MFAB Dept.Paint with black bituminous paint post survey IAW NO 12/2001 and refit back. Note : -The job involves removal of anchors and accessories, laying out for cleaning,painting d) Lug less joining shackles

032 Anchor and Anchor chain cable Anchor and Anchor chain cable and associated fittings are to be hydro jet blasted to bare metal, eased for free movement and to present for survey at NDV\MFAB Dept.Paint with black bituminous paint post survey IAW NO 12/2001 and refit back. Note : -The job involves removal of anchors and accessories, laying out for cleaning,painting and e) Cable stopper

032 Anchor and Anchor chain cable Anchor and Anchor chain cable and associated fittings are to be hydro jet blasted to bare metal, eased for free movement and to present for survey at NDV\MFAB Dept.Paint with black bituminous paint post survey IAW NO 12/2001 and refit back. Note : -The job involves removal of anchors and accessories, laying out for cleaning,painting and f) D Shackles

033 Anchor windlass/ Capstan (a) Completely strip & overhaul anchor windlass (including lub oil renewals), renew brake linings, refit and prove for satisfactory operation.Note :- Overhaul involves removal of drum, gearbox, brake lining, motor and ovrhaul of all these items and refitment. Oil-SYS-46/HP80

033 Capstan (b) Completely strip & overhaul Capstan and prove for satifactory operation.Note :- Overhaul involves removal of drum, gearbox, brake lining, motor and ovrhaul of all these items and refitment. Oil-SYS-46/HP80

034 Bollards Single bollards Following Single bollards corroded, thinned. Entire bollard to be renewed (a) Single bollards, Size: 290 mm dia, 10 mm thickness, 1300 mm length. schdule-80 pipe

034 Bollards Twin bollards (b) FollowingTwin bollards corroded, thinned. Entire bollard to be repaired/renewed as per Hull survey report. Dia of bollard pipe 290 MM. Height of bollard 515 MM. Size of bollard base/ foundation1163X125X380 MM: , Thickness of pipe: 10 mm. Doubler plate size: 1230X480X10 MM, thickness: 10 mm,

034 Large Twin bollards (c) Large Twin bollards corroded, thinned. Entire bollard to be repaired/ renewed as per Hull survey report. Dia of bollard pipe 340 MM. Height of bollard 1400MM. Size of bollard base/ foundation1575X575X10 MM: , Thickness of pipe: 10 mm. Doubler plate size: 1575X575X10 MM , thickness: 10 mm, TRIPPING BRACKET 150X10 MM

035 Key Fender securing arrangement (a) Removal of head and stern key fenders for hull survey.

035 Key Fender securing arrangement (b) Coaming plate and partition plates between fenders corroded, thinned and holed. All fittings to be renewed as per survey reports . Note: - Work involves removal of head and stern key fenders for hull survey and repair/ renewal of partition plates. Top and bottom securing brackets/ plates and partition plates size: 130mm x 8mm thick

035 Key Fender securing arrangement (c) Renewal of nuts and bolts - M24 DIA , Length of bolt rod varies between 1225 m to 620 mm.

035 Key Fender (d) All Head Key Fenders to be renewed with White colour fenders as per sizes. Specification - EPDM rubber as per NES 170. Crossection size 250mmx250mm. Length of fenders varies between 535mm to 790 mm. Note: Quote for material only view services covered at sl (a)

035 Key Fender (e) All Aft Key Fenders to be renewed with White colour fenders as per size Crossection size 250mmx250mm. Length of fenders varies between 526 mm to 1075 mm. Note: Quote for material only view services covered at sl (a)

036 Tyre Fender Tyre fenders damaged on P&S side to be renewed with used automobile tyre fenders moulded with 8 mm layer of white natural rubber on top and outer sides. Mat- Rubber, colour-white. No painting or coating of any other form will be permitted. Vendors to adhere to SoW (a) Tyre fender OD-1400 mm ID -1000 mm Width -350 mm

036 Tyre Fender Tyre fender damaged on P&S side to be renewed with used aircraft tyre fenders moulded with 8 mm layer of white natural rubber on top and outer sides. Mat- Rubber, colour-white. No painting or coating of any other form will be permitted. Vendors to adhere to SoW (b) OD 750mm; ID 450 mm , width - 350 mm

036 Tyre Fender securing arrangement Tyre fender to be secured with 14 mm dia chain on head, stern and ship side (a) Securing chains: 14mm dia(Mat-GI)

036 Tyre Fender securing arrangement Tyre fender to be secured with D shackles on ship side (b) D Shackles 14 mm dia(Mat-GI)

036 Tyre Fender securing arrangement Securing chain is to be passed through metallic sleeves inserted into the tyre fenders (c) Securing sleeves of dia 03 inch and length 250 mm (Mat MS pipe of 06mm thick)

036 Tyre Fender securing arrangement Tyre fenders securing eye plates to bo be welded along ships side for connecting of securing chains (d) Eye plate thickness 8 mm. (Mat - MS)

037 Bulwark (a)Bulwark at various places dented/damaged. To be included in hull in survey and renew as per survey report. Thickness-6 mm

037 Bulwark coaming (b) Bulwark coaming pipes corroded and thinned. To be included in hull in survey and renewed as per survey report. Dia 3 " Mat : MS

038 Sky light/port holes (a) Sky light at various places damaged including glass. Skylight/port holes is to be repaired/renewed as per sample.

038 Butterfly nuts. (b) Sky light- SS butterfly nuts and tumbler bolt of engine room sky light &exhaust flaps broken. To be renewed. Dia of bolt : 18 mm & 6 inch length

039 Metalic half pipe fender Metallic half pipe fender around the shipside to be repaired/renewed. (a) Size - 150mm dia, 08mm thick

039 Metalic half pipe fender Metallic half pipe fender around the shipside to be repaired/renewed. (b) Size - 160mm dia, 08 mm thick

040 Rubber beading. Rubber beading of doors at various places perished/cracked to be renewed and chalk test to be proved. As per NCD 5904 (a) Tensile strength Kg/cm2 (min %) 70 (b) Elongation at break (min %) 350 (c) Hardness shore A 50+/-5 ) (a) WT door

040 Rubber beading. Rubber beading of hatches at various places perished/crackedto be renewed and chalk test to be proved. As per NCD 5904 (a) Tensile strength Kg/cm2 (min %) 70 (b) Elongation at break (min %) 350 (c) Hardness shore A 50+/-5 ) b) WT hatch

040 Rubber beading. Rubber beading of skylight perished/crackedto be renewed and chalk test to be proved. As per NCD 5904 (a) Tensile strength Kg/cm2 (min %) 70 (b) Elongation at break (min %) 350 (c) Hardness shore A 50+/-5 ) (c) Ventilator/Sky light

040 Rubber beading. Rubber beading of funnel vantilator perished/crackedto be renewed and chalk test to be proved. As per NCD 5904 (a) Tensile strength Kg/cm2 (min %) 70 (b) Elongation at break (min %) 350 (c) Hardness shore A 50+/-5 ) (d) Funnel ventilator

041 Wire mesh SS Wire mesh and MS flaps of engine room exhaust opening corroded and broken. To be renewed. (Size of opening :01 m x 0.5 m)

042 Fish plate Fish plate and securing brackets corroded, thinned and holed. Mat: MS plate a) Fish plate size: 20x20 inch, 08mm thickness

042 Fish plate Fish plate and securing brackets corroded, thinned and holed. Mat: MS plate (b)Doubler plate size:28x28inch, 08 mm thickness

042 Fish plate Fish plate and securing brackets corroded, thinned and holed. Mat: MS plate (c) Angle bar 3 x1.5 inch

043 APT Air Pressure Test the following tanks and rectify the defects any observed during pressure testing and prove to 0.14 kg/ cm2. Note:- APT and proving of those tanks wherein steel renewal undertaken as part of steel renewal DL. 0003(c) above is that of Firm's liability with No Additional Cost and those tanks where no steel renewals undertaken only would be considered for payment as per the indicated rates under this DL. Serial. (a) Fresh Water Tank

043 APT Air Pressure Test the following tanks and rectify the defects any observed during pressure testing and prove to 0.14 kg/ cm2. Note:- APT and proving of those tanks wherein steel renewal undertaken as part of steel renewal DL. 0003(c) above is that of Firm's liability with No Additional Cost and those tanks where no steel renewals undertaken only would be considered for payment as per the indicated rates under this DL. Serial. (b) Ballast Tank

043 APT Air Pressure Test the following tanks and rectify the defects any observed during pressure testing and prove to 0.14 kg/ cm2. Note:- APT and proving of those tanks wherein steel renewal undertaken as part of steel renewal DL. 0003(c) above is that of Firm's liability with No Additional Cost and those tanks where no steel renewals undertaken only would be considered for payment as per the indicated rates under this DL. Serial. (c) Forepeak Tank and cofferdam

043 APT Air Pressure Test the following tanks and rectify the defects any observed during pressure testing and prove to 0.14 kg/ cm2. Note:- APT and proving of those tanks wherein steel renewal undertaken as part of steel renewal DL. 0003(c) above is that of Firm's liability with No Additional Cost and those tanks where no steel renewals undertaken only would be considered for payment as per the indicated rates under this DL. Serial. (d) Fuel Tank

043 APT Air Pressure Test the following tanks and rectify the defects any observed during pressure testing and prove to 0.14 kg/ cm2. Note:- APT and proving of those tanks wherein steel renewal undertaken as part of steel renewal DL. 0003(c) above is that of Firm's liability with No Additional Cost and those tanks where no steel renewals undertaken only would be considered for payment as per the indicated rates under this DL. Serial. (e) Firefighting Foam Tank

044 BIilge Platform (a) Renew bilge platform plate. Material- chequered aluminium, thickness- 05 mm

044 BIilge Platform (b) Bilge platform supporting brackets to be renewed where ever required. Mat - MS

045 Cleats MS cleats perished/thinned to be renewed (Size-28 mm). Mat : MS

046 Tank/Vent Pipe Vent pipes of various tanks on upper deck corroded and thinned, to be renewed. (Mat. GI pipe) (a) Pipe dia 2 1/2 inch

046 Tank/Vent Pipe Vent pipes of various tanks on upper deck corroded and thinned, to be renewed. (Mat. GI pipe) (b) Distance piece and flanges: Dia 150mm (including rubber joints)

047 WT Hatch clips (a) Hatch clips broken / damaged. To be renewed. Mat. MS

047 WT hatches (b) Hatch clips at various places jammed , to be lubricated including washer and fitted back

048 WT Doors (a) Clips of WT. Doors Jammed to be removed lubricated including washer, nut and fitted back

048 WT Hatch metal coaming (b) Metallic coaming of 05 in no WT Hatches on weather deckand various locations corroded and thinned. To be renewed as per survey report. Area - 20 Sqm.

049 NWT doors NWT wooden doors including frames of wheel house/crew cabin, master cabin perished /damaged. To be renewed/repaired

050 Ventilation Mushroom type ventilators on weather deck jammed ,to be removed, cleaned/ overhauled and fitted beck. Dia: 550mm (a) 550mm dia

051 Ventilation Mushroom type ventilators to be removed, cleaned/ overhauled and fitted back. Renew if required. (a) Details- Mush room head dia-1000 mm, Height-800 mm

051 Ventilation Mushroom type ventilators on weather deck jammed ,to be removed, cleaned/ overhauled and fitted beck. Dia:360 mm (b) 360mm dia

051 Ventilation (c) Air cleaning of ventilation trunking to be carried out. Location:- fitted at crew rest room , masters cabin, ED rest room galley/dinning hall . Mat-GI sheet

051 Ventilation (d) Ventilation trunking perished to be repaired/ renewed. Location: - crew rest room , masters cabin, ED rest room galley/dinning hall and fitted back . Mat-GI sheet

052 Breather pipe Breather pipe on weather deck perished/damage.To be renewed

053 Liferaft Securing stand of Life rafts perished and damaged. To be renewed alongwith rubber lining and supporting frame, including fitment of HRG Mat-MS . Thickness- 06mm.

054 Nav Light Nav light foundation (Port & Stbd) corroded, to be repaired/renewed. Size: 620mmx620mmx300mm and thickness 6mm, Mat MS

055 Drainage System MS Scupper lips with rubber packing corroded/thinned/holed, to be renewed at ship side

056 Drainage System (a)Deck Drain pipes corroded/ holed, to be renewed. Dia 2 1/2 inch. Mat: GI note : Pipes / fittings should be secured with rubber packing’s and clamps uniformly

057 Drainage System (b)Scupper with coaming of drain pipe corroded/ thinned, to be renewed. Size: 250mmx200mm

057 Drainage System (c) Deck drain pieces on upper deck corroded, to be renewed. Dia 2 1/2 inch, each of length 01Mtr. note-The job involves removal/renewal and fitment of pipes/ panelling/ lagging/ trunking in the way.

057 Drainage System. (d) Soil pipes of Crew, ED's and Master's bathroom to be removed chemically cleaned and fit back.

057 Pipelines Carry out pressure testing & repairs of soil pipe/drainaige pipe/fresh water lines fitted at various locations

057 Extinguishers Provision of following extinguishers to be undertaken (a) 9 Ltr AFFF extinguisher

057 Extinguishers Provision of following extinguishers to be undertaken (b) 2 Kg CO2 Extinguisher

057 Extinguishers Provision of following extinguishers to be undertaken (c) 10 Kg DCP extinguisher

058 FF items/Extinguishers Provision of following fire hoses to be undertaken Fire hoses

059 Foam solution Supply of Type 3% AFFF concentrate for forming mechanical foam and filling it in the foam tank

060 Fixed H2S Sensor (a) Provision of Fixed H2S sensors in the vicinity of STP compartment. (OEM - Hi-Point Services Pvt. Ltd.) Including installation of sensors and control pannel. Model-Honeywell Note:- Trial report along with H2S sensors calibration certificate by OEM to be submitted.

060 Portable H2S Sensors (b) Provision of Portable H2S sensors . (OEM - Hi-Point Services Pvt. Ltd.) Model - Altair Note:- Trial report alongwith H2S sensors calibration certificate by OEM to be submitted.

061 Sofa/cushion Sofa in master and engineer rest rooms torn/perished. To be renewed

062 Panelling Wooden panels in crew accommodation, Engg. rest room, master rest room and other places damaged. To be renewed

063 Furniture Wooden table damaged/broken at crew dinnig hall and crew cabin to be renewed.

064 Guard Rails Guard rails pipe damaged/ perished at Bridge deck. To be renewed. Material - GI Pipe .

065 Stanchion (a) Stanction on upper deck damaged/deformed at various loactions. To be repaired/renewed. Size- H - 970 mm and dia - 50 mm Mat- GI pipe

065 Stanchion (b) Securing chain between stanchions on upper deck damaged. To be renewed. Mat - MS, Size - 5 mm dia

066 Name board Following Tug name board perished/damaged, to be renewed/repaired. a) Repair/renewal of vessel name board including electroplating to be carried out on ship side -02

066 Name board Following Tug name board perished/damaged, to be renewed/repaired. b) Painting of tug name on bulwark in both Hindi and English at stem and stern with fluorescent paint -03

066 Name board Following Tug name board perished/damaged, to be renewed/repaired. c) Illuminated name board with Perspex sheet - 01

067 Door locks (a) Mortise lock of non WT door defective at various locations, All defective mortise locks to be renewed. including 03 set of keys

067 Door locks (b) Locking arrangement is to be provided for wt doors at various locations, including hasp & staples and pad locks

068. Sanitary system SS Wash basin damaged in crew batroom and wc to be repaired as indicated (a) Wash basin

068 Sanitary system SS tap damaged in crew batroom and wc to be repaired as indicated b) SS tap: 1/2 inch

068 Sanitary system supply pipes damaged-corroded/thinned/holed in crew batroom and wc to be repaired as indicated c) Supply pipe: Mat : Cu-Ni, dia: ½’’

068 Sanitary system drain pipes damaged-corroded/thinned/holed in crew batroom and wc to be repaired as indicated d) Drain pipe: Mat-MS,dia- 2’’

069 Sanitary system Flush valves damaged-corroded/thinned/holed in crew batroom and wc to be repaired as indicated e) Flush valves - Mat - Brass, Dia - 2"

070 Sanitary system PVC Wash basin Drain Pipe Line Damaged To Be Renewed As Indicated f) PVC drain pipe Note:- Quoted repair cost shall include cost all items.

071 WC/Commode WC commode and base plate in crew wash room perished/corroded, to be renewed. Mat - SS

072 Bathroom fittings Bathroom fittings damged/broken in crew bathrooms and master bathroom , to be renewed as per sample (b)cu -ni supply pipes

072 Bathroom fittings Bathroom fittings damged/broken in crew bathrooms and master bathroom , to be renewed as per sample (c) Shower head

073 Deck underlay Deck Covering to be repaired/ renewed at uprooted/ damaged/ steel renewed places, accommodation areas, Wheel house and wet compartments. NOTE:- Dry Compt area-110 SQM, Wet Compt Area-30 SQM, Dadoes area- 15 SQM (a) Surface preparation and application of EROP. As per NCD 3717

073 Deck underlay Deck Covering to be repaired/ renewed at uprooted/ damaged/ steel renewed places, accommodation areas, Wheel house and wet compartments NOTE;- Dry Compt area-110 SQM, Wet Compt Area-30 SQM, Dadoes area- 15 SQM (b) Application of Underlay as per NCD 3717

073 Deck underlay Deck Covering to be repaired/ renewed at uprooted/ damaged/ steel renewed places, accommodation areas, Wheel house and wet compartments NOTE;- Dry Compt area-110 SQM, Wet Compt Area-30 SQM, Dadoes area- 15 SQM (c) Application of sealer coat and top coat on entire area As Per NCD 3717.

074 Foundation Foundation of deck machinery / deck fittings corroded/thinned/perished , to be renewed as per survey report

075 Wooden platform Wooden platform in wheel house to be manufactured , mat-hard wood , size- 3X2 mtr , Height- 300 mm

076 Lagging Lagging at indicated places to be removed to facilitate structural repairs and to be renewed with new lagging post completion of repairs.mat-ss

077 Deck head panelling/ Sunmicia Panelling at indicated places to be removed to facilitate structural repairs and to be refitted post completion of repairs. Mat : wooden

078 Panelling Panelling at indicated places including wet Compt to be removed to facilitate structural repairs and to be refitted post completion of repairs. Mat : SS

079 Wet compartment Dadoe area Dadoe areas of wet compartments corroded, thinned and holed to be renewed. (Mat- MS)

080 Manhole (a) Manhole covers corroded/ thinned To be renewed as per survey report Mat - IS 2062 Grade 'B' steel. Size - 2' X 1.5'

080 Manhole (b) Rubber joints deterioted, to be renewed

080 Manhole (c) studs of manholes corroded, to be renewed. Only defective studs which are found defective on survey to be renewed. MS Studs with nut, size 20 mm

081 Bulwark Door Bulwark door jammed on P & S side , entire door to be removed for necessary repairs and fitted back

082 Hatch Cover Hatch cover in bridge corroded/thinned/holed, cover to be renewed. Mat-Al

ENGINEERING WORK PACKAGE- BALDEV SR-2020 1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM Present Running Hours - PME : 1686 hrs, SME: 1692 hrs Following routines to be carried out by the OEM on both Main Engines. Post completion of routines MEs to be proved for satisfactory operation ( Firm Not To Quote )

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM a) Clean / Inspect sea water strainers.

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM b) Replace corrosion protection zinc rods

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM c) Replace engine air filter element.

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM d) Clean crank case breather.

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM e) Replace engine oil filter.

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM f) Replace fuel system primary filter (water seperator) element.

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM g) Replace all hoses and clamps.

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM h) Clean and pressure test after cooler core.

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM j) Replace fumes diposal filter.

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM k) Overhaul turbo charger and replace both clamp rings.

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM l) Calibrate instrumentation and safety devices.

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM m) Overhauling of auxilary sea water pump including replacement of Impeller, wear rings, seals, and bearings.

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM n) Replace coolant temparature regulator.

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM p) Inspect crankcase vibration damper.

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM q) Inspect engine mounts for deterioration and for proper torque.

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM r) Inspect / clean / calibrate engine speed / timing sensor.

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM s) Check engine valve lash

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM t) Inspect engine valve rotators.

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM u) Carry out Inspection / calibration / adjustment of fuel injectors.

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM v) Chemical cleaning and pressure testing of plate type heat exchangers .Spares required for undertaking routines to be included in quote.

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM w) Overhaul starting motor. All parts required for overhauling to be included in quote.

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM x) Calibration of fuel injectors.and fuel pump.

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM y) Overhauling of turbo charger to be carried out.

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM z) Replace coolant.

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM aa) Cleaning of Lub oil sump and Change Engine oil. (Oil 15W40)

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM ab) Chemical cleaning and painting ( heat resistant ) of exhaust Pipe of both MEs. Size 200 mm

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM ac) Mechanical cleaning of exhaust drain line of both MEs, Size 20 mm.

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM ad) Replace fuel system secondary filter.

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM ae) All safety cut outs/trips to be calibrated and proved for satisfactory operations

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM af) Performance trials post completion of routines for satisfactory performance.

1001, EQPT : MAIN ENGINES, MAKE : CATERPILLER, MODEL-C32, SL NO:-PORT-RN401211, STBD-RN401209, MAX OUTPUT-850BHP@1800RPM ag) Replace intercooler .all spares for reneewal to be included in quote

1002, EQPT: DIESEL GENERATORS, MAKE-KOEL, MODEL-6R1080T, OUTPUT-127BHP@1500RPM,SL NO:-FWD-6H9495/1100804,AFT-6H9496/1100805 Present Running Hours - PDG : 907 hrs, SME: 1036 hrs( Following routines to be carried out by the OEM, Post completion of above routines DGs to be proved for satisfactory operation, ( Firm Not To Quote )

1002, EQPT: DIESEL GENERATORS, MAKE-KOEL, MODEL-6R1080T, OUTPUT-127BHP@1500RPM,SL NO:-FWD-6H9495/1100804,AFT-6H9496/1100805 a) Clean fuel oil strainers.

1002, EQPT: DIESEL GENERATORS, MAKE-KOEL, MODEL-6R1080T, OUTPUT-127BHP@1500RPM,SL NO:-FWD-6H9495/1100804,AFT-6H9496/1100805 b) Replace fuel filter catrigdes.

1002, EQPT: DIESEL GENERATORS, MAKE-KOEL, MODEL-6R1080T, OUTPUT-127BHP@1500RPM,SL NO:-FWD-6H9495/1100804,AFT-6H9496/1100805 c) Replacement of V belts.

1002, EQPT: DIESEL GENERATORS, MAKE-KOEL, MODEL-6R1080T, OUTPUT-127BHP@1500RPM,SL NO:-FWD-6H9495/1100804,AFT-6H9496/1100805 d) Change main element of dry type air cleaner.

1002, EQPT: DIESEL GENERATORS, MAKE-KOEL, MODEL-6R1080T, OUTPUT-127BHP@1500RPM,SL NO:-FWD-6H9495/1100804,AFT-6H9496/1100805 e) Replace lub oil filter catridges.

1002, EQPT: DIESEL GENERATORS, MAKE-KOEL, MODEL-6R1080T, OUTPUT-127BHP@1500RPM,SL NO:-FWD-6H9495/1100804,AFT-6H9496/1100805 f) Change Engine oil. (15W40)

1002, EQPT: DIESEL GENERATORS, MAKE-KOEL, MODEL-6R1080T, OUTPUT-127BHP@1500RPM,SL NO:-FWD-6H9495/1100804,AFT-6H9496/1100805 g) Replace all rubber / flexible hoses and clips of system pipes.

1002, EQPT: DIESEL GENERATORS, MAKE-KOEL, MODEL-6R1080T, OUTPUT-127BHP@1500RPM,SL NO:-FWD-6H9495/1100804,AFT-6H9496/1100805 h) Removal ,internal cleaning and pressure testing of heat exchanger.

1002, EQPT: DIESEL GENERATORS, MAKE-KOEL, MODEL-6R1080T, OUTPUT-127BHP@1500RPM,SL NO:-FWD-6H9495/1100804,AFT-6H9496/1100805 j) Chemical cleaning of expansion tank to be carried out.

1002, EQPT: DIESEL GENERATORS, MAKE-KOEL, MODEL-6R1080T, OUTPUT-127BHP@1500RPM,SL NO:-FWD-6H9495/1100804,AFT-6H9496/1100805 k) Replenish coolant.

1002, EQPT: DIESEL GENERATORS, MAKE-KOEL, MODEL-6R1080T, OUTPUT-127BHP@1500RPM,SL NO:-FWD-6H9495/1100804,AFT-6H9496/1100805 l) Calibration of fuel injectors and fuel pumps to be carried out

1002, EQPT: DIESEL GENERATORS, MAKE-KOEL, MODEL-6R1080T, OUTPUT-127BHP@1500RPM,SL NO:-FWD-6H9495/1100804,AFT-6H9496/1100805 m) Overhauling of seawater pump to be carried out.

1002, EQPT: DIESEL GENERATORS, MAKE-KOEL, MODEL-6R1080T, OUTPUT-127BHP@1500RPM,SL NO:-FWD-6H9495/1100804,AFT-6H9496/1100805 n) Overhauling of turbo charger to be carried out including both (in &out) clamp hose renewal.

1002, EQPT: DIESEL GENERATORS, MAKE-KOEL, MODEL-6R1080T, OUTPUT-127BHP@1500RPM,SL NO:-FWD-6H9495/1100804,AFT-6H9496/1100805 p) Chemical cleaning and painting ( heat resistant ) of exhaust Pipe of both DAs. Size 80 mm

1002, EQPT: DIESEL GENERATORS, MAKE-KOEL, MODEL-6R1080T, OUTPUT-127BHP@1500RPM,SL NO:-FWD-6H9495/1100804,AFT-6H9496/1100805 n) Mechanical cleaning of exhaust drain line of both DAs, Size 20 mm.

1002, EQPT: DIESEL GENERATORS, MAKE-KOEL, MODEL-6R1080T, OUTPUT-127BHP@1500RPM,SL NO:-FWD-6H9495/1100804,AFT-6H9496/1100805 q) Carry out Overhauling of engine driven sea water pumps.

1002, EQPT: DIESEL GENERATORS, MAKE-KOEL, MODEL-6R1080T, OUTPUT-127BHP@1500RPM,SL NO:-FWD-6H9495/1100804,AFT-6H9496/1100805 r) Carry out Overhauling of engine driven coolant pumps.

1002, EQPT: DIESEL GENERATORS, MAKE-KOEL, MODEL-6R1080T, OUTPUT-127BHP@1500RPM,SL NO:-FWD-6H9495/1100804,AFT-6H9496/1100805 s) Zinc plugs of cooler to be replaced ( as per sample)

1002, EQPT: DIESEL GENERATORS, MAKE-KOEL, MODEL-6R1080T, OUTPUT-127BHP@1500RPM,SL NO:-FWD-6H9495/1100804,AFT-6H9496/1100805 t) Inspection of engine mounts and replace if detereorated.

1002, EQPT: DIESEL GENERATORS, MAKE-KOEL, MODEL-6R1080T, OUTPUT-127BHP@1500RPM,SL NO:-FWD-6H9495/1100804,AFT-6H9496/1100805 u) Post completion of above routines DGs to be proved for satisfactory operation.

1002, EQPT: DIESEL GENERATORS, MAKE-KOEL, MODEL-6R1080T, OUTPUT-127BHP@1500RPM,SL NO:-FWD-6H9495/1100804,AFT-6H9496/1100805 v) Cleaning,moping,masking and spray painting of DA with heat resistant equipment paint.

1003 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 (Firm Not To Quote) Following Drydock routines to be carried out by the OEM

1003 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 a) Chemical cleaning and pressure testing of lub oil coolers to be carried out.

1003 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 b) Check the seals of the propeller shaft, seals of the steering tube and of the input shaft. Renew if required

1003 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 c) Check the condition of the gears through the inspection hatches

1003 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 d) Lub oil in sump to be completely drained and new oil charged SP 150 ( lub oil will be supplied by department)

1003 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 e) Hydraulic oil to be drained and new oil charged Servo System 46 ( lub oil will be supplied by department)

1003 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 f) Renew hydraulic oil filter elements.

1003 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 g) Renew lub oil filter elements.

1003 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 h) Greasing of universal shaft joints to be carried out

1003 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 j) Intermediate shaft bearings to be dismantled and old grease removed. Greasing of bearing to be carried out thereafter Grease type EP-2

1003 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 k) All flexible hoses/ durettes to be renewed

1003 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 l) Check Propeller condition

1003 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 m) Rudder Propellers- Check tightening of Bolts & Nuts

1003 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 n) Check Sacrificial anodes. Replace all anodes.

1003 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 p) Lub Oil pressure switch to be renewed with calibrated gauges.quote to include spares

1003 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 q) Clutch oil pressure gauge to be renewed with calibrated gauge.new gauge to be procured

1003 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 r) Luboil pressure gauge to be calibrated

1003 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 s) Thermometers to be replaced.

1003 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 t) Performance trials post completion of routines for satisfactory performance.

1004, EQPT/SYSTEM: AIR COMPRESSOR , MAKE : INGERSOLL-RAND,NARODA, TYPE-ELECTRIC DRIVEN, HIGH PRESSURE RECIPROCATING,MODEL-251X5,CAP-8Cu.M/Hr@30BAR. ( Firm Not To Quote )

1004, EQPT/SYSTEM: AIR COMPRESSOR , MAKE : INGERSOLL-RAND,NARODA, TYPE-ELECTRIC DRIVEN, HIGH PRESSURE RECIPROCATING,MODEL-251X5,CAP-8Cu.M/Hr@30BAR. a) Compressor to be overhauled, with replacement of all joints, renewal of weardown parts as required post inspection by the QC. After fitment of all accessories compressor to be proved for satisfactory operation. Duration-02 Hrs

1004, EQPT/SYSTEM: AIR COMPRESSOR , MAKE : INGERSOLL-RAND,NARODA, TYPE-ELECTRIC DRIVEN, HIGH PRESSURE RECIPROCATING,MODEL-251X5,CAP-8Cu.M/Hr@30BAR. b) Renewed drive belt,Size-B68,

1004, EQPT/SYSTEM: AIR COMPRESSOR , MAKE : INGERSOLL-RAND,NARODA, TYPE-ELECTRIC DRIVEN, HIGH PRESSURE RECIPROCATING,MODEL-251X5,CAP-8Cu.M/Hr@30BAR. c) Discahrge pr gauge to be renewed.Raange:-0 to 45 kg/cm2

1004, EQPT/SYSTEM: AIR COMPRESSOR , MAKE : INGERSOLL-RAND,NARODA, TYPE-ELECTRIC DRIVEN, HIGH PRESSURE RECIPROCATING,MODEL-251X5,CAP-8Cu.M/Hr@30BAR. d) Change compressor oil. (provided by Navy)

1004, EQPT/SYSTEM: AIR COMPRESSOR , MAKE : INGERSOLL-RAND,NARODA, TYPE-ELECTRIC DRIVEN, HIGH PRESSURE RECIPROCATING,MODEL-251X5,CAP-8Cu.M/Hr@30BAR. e) Cut IN / cut OUT pressure switches to be renewed with calibrated switches. calibration certiifcates to be rendered.

1004, EQPT/SYSTEM: AIR COMPRESSOR , MAKE : INGERSOLL-RAND,NARODA, TYPE-ELECTRIC DRIVEN, HIGH PRESSURE RECIPROCATING,MODEL-251X5,CAP-8Cu.M/Hr@30BAR. f) Non Return Valve to be fitted on comp discharge line between compressor and air bottle) SDNR, 20mm,

1004, EQPT/SYSTEM: AIR COMPRESSOR , MAKE : INGERSOLL-RAND,NARODA, TYPE-ELECTRIC DRIVEN, HIGH PRESSURE RECIPROCATING,MODEL-251X5,CAP-8Cu.M/Hr@30BAR. g) replace shock mounts.new mounts to to be tested and grouped before fitment. Testing certificates to be included.

1005, EQPT/SYSTEM: AIR COMPRESSOR , MAKE : ELGI, TYPE-ELECTRIC DRIVEN, HIGH PRESSURE RECIPROCATING, CAP-8Cu.M/Hr@30BAR. (Firm Not To Quote)

1005, EQPT/SYSTEM: AIR COMPRESSOR , MAKE : ELGI, TYPE-ELECTRIC DRIVEN, HIGH PRESSURE RECIPROCATING, CAP-8Cu.M/Hr@30BAR a) Compressor to be overhauled, with replacement of all joints, renewal of weardown parts as required post inspection by the QC. After fitment of all accessories compressor to be proved for satisfactory operation. Duration-02 Hrs

1005, EQPT/SYSTEM: AIR COMPRESSOR , MAKE : ELGI, TYPE-ELECTRIC DRIVEN, HIGH PRESSURE RECIPROCATING, CAP-8Cu.M/Hr@30BAR b) Renewed drive belt,Size-B68,

1005, EQPT/SYSTEM: AIR COMPRESSOR , MAKE : ELGI, TYPE-ELECTRIC DRIVEN, HIGH PRESSURE RECIPROCATING, CAP-8Cu.M/Hr@30BAR c) Discahrge pr gauge to be renewed.Range:-0 to 45 kg/cm2

1005, EQPT/SYSTEM: AIR COMPRESSOR , MAKE : ELGI, TYPE-ELECTRIC DRIVEN, HIGH PRESSURE RECIPROCATING, CAP-8Cu.M/Hr@30BAR d) Change compressor oil. (provided by Navy)

1005, EQPT/SYSTEM: AIR COMPRESSOR , MAKE : ELGI, TYPE-ELECTRIC DRIVEN, HIGH PRESSURE RECIPROCATING, CAP-8Cu.M/Hr@30BAR e) Cut IN / cut OUT pressure switches to be calibrated, and certiifcates to be rendered.

1005, EQPT/SYSTEM: AIR COMPRESSOR , MAKE : ELGI, TYPE-ELECTRIC DRIVEN, HIGH PRESSURE RECIPROCATING, CAP-8Cu.M/Hr@30BAR g) replace shock mounts.new mounts to to be tested and grouped before fitment. Testing certificates to be included.

1006, EQPT:-FUEL OIL TRANSFER PUMP,MAKE-TUSHACO PUMP,MODEL-R20DG,CAPACITY- 5 Cu.M/Hr@2KG/CM2,SL NO:-TOP-1330022/1945 , BOTTOM-1330022/1944 ( Firm Not To Quote )

1006, EQPT:-FUEL OIL TRANSFER PUMP,MAKE-TUSHACO PUMP,MODEL-R20DG,CAPACITY- 5 Cu.M/Hr@2KG/CM2,SL NO:-TOP-1330022/1945 , BOTTOM-1330022/1944 a) Pump to be overhauled, with replacement of mechanical seals, shaft key, and bearings.

1006, EQPT:-FUEL OIL TRANSFER PUMP,MAKE-TUSHACO PUMP,MODEL-R20DG,CAPACITY- 5 Cu.M/Hr@2KG/CM2,SL NO:-TOP-1330022/1945 , BOTTOM-1330022/1944 b) Suction and discharge pressure gauges(one each) to be replaced. Suction gauge Range -0.5 to 5 bar and discharge gauge reange 0 to 10 bar. The gauges should be of glycerine filled.

1006, EQPT:-FUEL OIL TRANSFER PUMP,MAKE-TUSHACO PUMP,MODEL-R20DG,CAPACITY- 5 Cu.M/Hr@2KG/CM2,SL NO:-TOP-1330022/1945 , BOTTOM-1330022/1944 c) Instrumentation gauges pipes (RMT- 02 mtrs) with suitable end fittings and isolating cock (qty-02) to be renewed. Mat: CuNi, Dia:1/4 inch.

1006, EQPT:-FUEL OIL TRANSFER PUMP,MAKE-TUSHACO PUMP,MODEL-R20DG,CAPACITY- 5 Cu.M/Hr@2KG/CM2,SL NO:-TOP-1330022/1945 , BOTTOM-1330022/1944 d) Pump coupling guard ((U shape, mesh type, with end plate Material -MS, thickness 2 mm)) to be renewed, Gaurd Full Length 48 cm, width- 18 cm.

1006, EQPT:-FUEL OIL TRANSFER PUMP,MAKE-TUSHACO PUMP,MODEL-R20DG,CAPACITY- 5 Cu.M/Hr@2KG/CM2,SL NO:-TOP-1330022/1945 , BOTTOM-1330022/1944 e) Renewal of spider jaw copuling

1006, EQPT:-FUEL OIL TRANSFER PUMP,MAKE-TUSHACO PUMP,MODEL-R20DG,CAPACITY- 5 Cu.M/Hr@2KG/CM2,SL NO:-TOP-1330022/1945 , BOTTOM-1330022/1944 f) All foundation nut and bolts (qty 04, M 20, Material -SS) to be renewed.

1006, EQPT:-FUEL OIL TRANSFER PUMP,MAKE-TUSHACO PUMP,MODEL-R20DG,CAPACITY- 5 Cu.M/Hr@2KG/CM2,SL NO:-TOP-1330022/1945 , BOTTOM-1330022/1944 g) Fitment and Alignment of pump with motor. Pump to be proved for satisfactory performance (working pressure 2 bar) on board with sytem line fitted.

1006, EQPT:-FUEL OIL TRANSFER PUMP,MAKE-TUSHACO PUMP,MODEL-R20DG,CAPACITY- 5 Cu.M/Hr@2KG/CM2,SL NO:-TOP-1330022/1945 , BOTTOM-1330022/1944 h) Non Return valves to be procured and fitted in suction line of the FT pp.near tank top(service tank). Size 50 mm, Mat. Gun metal.

1007, EQPT : FUEL OIL CENTRIFUGE, MAKE-ALFA LAVEL INDIA LTD, PUNE.,CAPACITY-1000LPH @ 1.5KG/CM2,SL NO-4202282-2011 ( Firm Not To Quote )

1007, EQPT : FUEL OIL CENTRIFUGE, MAKE-ALFA LAVEL INDIA LTD, PUNE.,CAPACITY-1000LPH @ 1.5KG/CM2,SL NO-4202282-2011 a) Centrifuge bowl assembly to be dismentled. All conical disc to be removed cleaned and fitted back.

1007, EQPT : FUEL OIL CENTRIFUGE, MAKE-ALFA LAVEL INDIA LTD, PUNE.,CAPACITY-1000LPH @ 1.5KG/CM2,SL NO-4202282-2011 b) Renew gravity disc and Minor service routines to be carried out.

1007, EQPT : FUEL OIL CENTRIFUGE, MAKE-ALFA LAVEL INDIA LTD, PUNE.,CAPACITY-1000LPH @ 1.5KG/CM2,SL NO-4202282-2011 c) Suction and discharge pr gauges to be renewed.range:- -01 kg/cm2 to 3 kg/cm2.

1007, EQPT : FUEL OIL CENTRIFUGE, MAKE-ALFA LAVEL INDIA LTD, PUNE.,CAPACITY-1000LPH @ 1.5KG/CM2,SL NO-4202282-2011 d) Instrumentation gauges pipes (RMT- 02 mtrs) with suitable end fittings to be renewed. Mat: CuNi, Dia:1/4 inch.

1007, EQPT : FUEL OIL CENTRIFUGE, MAKE-ALFA LAVEL INDIA LTD, PUNE.,CAPACITY-1000LPH @ 1.5KG/CM2,SL NO-4202282-2011 e) Drive shaft centrifugal cluth pads to be renewed.

1007, EQPT : FUEL OIL CENTRIFUGE, MAKE-ALFA LAVEL INDIA LTD, PUNE.,CAPACITY-1000LPH @ 1.5KG/CM2,SL NO-4202282-2011 f) Centrifuge to be proved for satisfactory performance post work completion.

1008, EQPT: LUB OIL TRANSFER PUMP,MAKE-TUSHACO PUMPS,MODEL-R 20 DG, CAPACITY-1 Cu.M/Hr@2KG/CM2,SL NO:-PORT-1330022/1941,STBD-1330022/1942 ( Firm Not To Quote )

1008, EQPT: LUB OIL TRANSFER PUMP,MAKE-TUSHACO PUMPS,MODEL-R 20 DG, CAPACITY-1 Cu.M/Hr@2KG/CM2,SL NO:-PORT-1330022/1941,STBD-1330022/1942 a) Pump to be overhauled, with replacement of mechanical seals, shaft key, and bearings.

1008, EQPT: LUB OIL TRANSFER PUMP,MAKE-TUSHACO PUMPS,MODEL-R 20 DG, CAPACITY-1 Cu.M/Hr@2KG/CM2,SL NO:-PORT-1330022/1941,STBD-1330022/1942 b) Suction and discharge pressure gauges(one each) to be replaced. Suction gauge Range -0.5 to 5 bar and discharge gauge reange 0 to 10 bar. The gauges should be of glycerine filled.

1008, EQPT: LUB OIL TRANSFER PUMP,MAKE-TUSHACO PUMPS,MODEL-R 20 DG, CAPACITY-1 Cu.M/Hr@2KG/CM2,SL NO:-PORT-1330022/1941,STBD-1330022/1942 c) Instrumentation gauges pipes (RMT- 02 mtrs) with suitable end fittings and isolating cock (qty-02) to be renewed. Mat: CuNi, Dia:1/4 inch.

1008, EQPT: LUB OIL TRANSFER PUMP,MAKE-TUSHACO PUMPS,MODEL-R 20 DG, CAPACITY-1 Cu.M/Hr@2KG/CM2,SL NO:-PORT-1330022/1941,STBD-1330022/1942 d) Pump coupling guard (U shape, mesh type, with end plate Material -MS, thickness 2 mm) to be renewed, Gaurd Full Length 48 cm, width- 18 cm.

1008, EQPT: LUB OIL TRANSFER PUMP,MAKE-TUSHACO PUMPS,MODEL-R 20 DG, CAPACITY-1 Cu.M/Hr@2KG/CM2,SL NO:-PORT-1330022/1941,STBD-1330022/1942 e) Renewal of spider jaw copuling (qty-01)

1008, EQPT: LUB OIL TRANSFER PUMP,MAKE-TUSHACO PUMPS,MODEL-R 20 DG, CAPACITY-1 Cu.M/Hr@2KG/CM2,SL NO:-PORT-1330022/1941,STBD-1330022/1942 f) All foundation nut and bolts (qty 04, M 20, Material -SS) to be renewed.

1008, EQPT: LUB OIL TRANSFER PUMP,MAKE-TUSHACO PUMPS,MODEL-R 20 DG, CAPACITY-1 Cu.M/Hr@2KG/CM2,SL NO:-PORT-1330022/1941,STBD-1330022/1942 g) Fitment and Alignment of pump with motor. Pump to be proved for satisfactory performance (working pressure 2 bar) on board with sytem line fitted.

1009, EQPT/SYSTEM:LUB OIL CENTRIFUGE,MAKE-ALFA LAVAL INDIA LTD.,PUNE, [email protected] KG/CM2,SL NO-4202005-2011 ( Firm Not To Quote )

1009, EQPT/SYSTEM:LUB OIL CENTRIFUGE,MAKE-ALFA LAVAL INDIA LTD.,PUNE, [email protected] KG/CM2,SL NO-4202005-2011 a) Centrifuge bowl assembly to be dismentled. All conical discs to be removed cleaned and fitted back.

1009, EQPT/SYSTEM:LUB OIL CENTRIFUGE,MAKE-ALFA LAVAL INDIA LTD.,PUNE, [email protected] KG/CM2,SL NO-4202005-2011 b) Renew gravity disc. and.Minor service routines to be carried out.

1009, EQPT/SYSTEM:LUB OIL CENTRIFUGE,MAKE-ALFA LAVAL INDIA LTD.,PUNE, [email protected] KG/CM2,SL NO-4202005-2011 c) Suction and discharge pr gauges to be renewed.range:- -01 kg/cm2 to 3 kg/cm2 and 0.0kg/cm2 to 10 kg/cm2 respectively.

1009, EQPT/SYSTEM:LUB OIL CENTRIFUGE,MAKE-ALFA LAVAL INDIA LTD.,PUNE, [email protected] KG/CM2,SL NO-4202005-2011 d) Drive shaft centrifugal cluth pads to be renewed.

1009, EQPT/SYSTEM:LUB OIL CENTRIFUGE,MAKE-ALFA LAVAL INDIA LTD.,PUNE, [email protected] KG/CM2,SL NO-4202005-2011 e) Centrifuge to be proved for satisfactory performance post work completion.

1010, EQPT/SYSTEM: OILY BILGE WATER SEPARATOR,MAKE:-BLOHM-VOSS INDUSTRIES GMBH,HAMBURG,TYPE-TMPB-0.5, CAPACITY-0.5CuM/[email protected] BAR OVERBOARD PRESSURE , SUCTION HEAD:- -0.6BAR AT SEPARATOR INLET,DISCHARGE HEAD-2.5 BAR ( Firm Not To Quote )

1010, EQPT/SYSTEM: OILY BILGE WATER SEPARATOR,MAKE:-BLOHM-VOSS INDUSTRIES GMBH,HAMBURG,TYPE-TMPB-0.5, CAPACITY-0.5CuM/[email protected] BAR OVERBOARD PRESSURE , SUCTION HEAD:- -0.6BAR AT SEPARATOR INLET,DISCHARGE HEAD-2.5 BAR a) OWS to be completelly dismantled.renewed defective parts and fitted back.

1010, EQPT/SYSTEM: OILY BILGE WATER SEPARATOR,MAKE:-BLOHM-VOSS INDUSTRIES GMBH,HAMBURG,TYPE-TMPB-0.5, CAPACITY-0.5CuM/[email protected] BAR OVERBOARD PRESSURE , SUCTION HEAD:- -0.6BAR AT SEPARATOR INLET,DISCHARGE HEAD-2.5 BAR b) Overhaul Gate valves dia-15mm .

1010, EQPT/SYSTEM: OILY BILGE WATER SEPARATOR,MAKE:-BLOHM-VOSS INDUSTRIES GMBH,HAMBURG,TYPE-TMPB-0.5, CAPACITY-0.5CuM/[email protected] BAR OVERBOARD PRESSURE , SUCTION HEAD:- -0.6BAR AT SEPARATOR INLET,DISCHARGE HEAD-2.5 BAR c) Renew needle valves.

1010, EQPT/SYSTEM: OILY BILGE WATER SEPARATOR,MAKE:-BLOHM-VOSS INDUSTRIES GMBH,HAMBURG,TYPE-TMPB-0.5, CAPACITY-0.5CuM/[email protected] BAR OVERBOARD PRESSURE , SUCTION HEAD:- -0.6BAR AT SEPARATOR INLET,DISCHARGE HEAD-2.5 BAR d) Supply oil pump to be overhauled, with renewal of mechanical seals, shaft key, bearings.

1010, EQPT/SYSTEM: OILY BILGE WATER SEPARATOR,MAKE:-BLOHM-VOSS INDUSTRIES GMBH,HAMBURG,TYPE-TMPB-0.5, CAPACITY-0.5CuM/[email protected] BAR OVERBOARD PRESSURE , SUCTION HEAD:- -0.6BAR AT SEPARATOR INLET,DISCHARGE HEAD-2.5 BAR e) Seperator housing to be cleaned internally.

1010, EQPT/SYSTEM: OILY BILGE WATER SEPARATOR,MAKE:-BLOHM-VOSS INDUSTRIES GMBH,HAMBURG,TYPE-TMPB-0.5, CAPACITY-0.5CuM/[email protected] BAR OVERBOARD PRESSURE , SUCTION HEAD:- -0.6BAR AT SEPARATOR INLET,DISCHARGE HEAD-2.5 BAR f) OWS to be proved for satisfactory performance post work completion.

1011, EQPT:-DIRTY OIL PUMP,MAKE-TUSHACO PUMP,MODEL-R20DG, CAPACITY- 1 Cu.M/Hr@2KG/CM2,SL NO:-133002/1938 ( Firm Not To Quote )

1011, EQPT:-DIRTY OIL PUMP,MAKE-TUSHACO PUMP,MODEL-R20DG, CAPACITY- 1 Cu.M/Hr@2KG/CM2,SL NO:-133002/1938 a) Pump to be overhauled, with renewal of mechanical seals, shaft key, bearings.

1011, EQPT:-DIRTY OIL PUMP,MAKE-TUSHACO PUMP,MODEL-R20DG, CAPACITY- 1 Cu.M/Hr@2KG/CM2,SL NO:-133002/1938 b) Fitment and Alignment of pump with motor. Renewal of spider jaw copuling (qty-01) and all foundation nut and bolts (qty 04, M 20, Material -SS)

1011, EQPT:-DIRTY OIL PUMP,MAKE-TUSHACO PUMP,MODEL-R20DG, CAPACITY- 1 Cu.M/Hr@2KG/CM2,SL NO:-133002/1938 c) Suction and discharge pressure gauges(one each) to be replaced. Suction gauge Range -0.5 to 3 bar and discharge gauge reange 0 to 10 bar. The gauges should be glycerine filled.

1011, EQPT:-DIRTY OIL PUMP,MAKE-TUSHACO PUMP,MODEL-R20DG, CAPACITY- 1 Cu.M/Hr@2KG/CM2,SL NO:-133002/1938 d) Instrumentation gauges pipes (RMT- 02 mtrs) with suitable end fittings and isolating cock (qty-02) to be renewed. Mat: CuNi, Dia:1/4 inch.

1011, EQPT:-DIRTY OIL PUMP,MAKE-TUSHACO PUMP,MODEL-R20DG, CAPACITY- 1 Cu.M/Hr@2KG/CM2,SL NO:-133002/1938 e) Proving of Pump (working pressure 2 bar) on board with sytem line fitted, upto 6 bar relief pressure

1011, EQPT:-DIRTY OIL PUMP,MAKE-TUSHACO PUMP,MODEL-R20DG, CAPACITY- 1 Cu.M/Hr@2KG/CM2,SL NO:-133002/1938 f) Pump coupling guard ((U shape, mesh type, with end plate Material -MS, thickness 2 mm) to be renewed, Gaurd Full Length 48 cm, width- 18 cm.

1012, EQPT:-BILGE AND GENERAL SERVICE PUMPS, MAKE-BE PUMPS MODEL-SH65-160MN1-DGS2-316 , CAPACITY-30Cu.M/Hr@25MWC , SL NO:-AFT-560245,FWD-360251 ( Firm Not To Quote )

1012, EQPT:-BILGE AND GENERAL SERVICE PUMPS, MAKE-BE PUMPS MODEL-SH65-160MN1-DGS2-316 , CAPACITY-30Cu.M/Hr@25MWC , SL NO:-AFT-560245,FWD-360251 a) Overhaul the pump completely and prove for satisfactory operation (Working pressure -6 Bar) . Overhaul shall include renewal of impeller, bearings, mechanical seal and shaft key.

1012, EQPT:-BILGE AND GENERAL SERVICE PUMPS, MAKE-BE PUMPS MODEL-SH65-160MN1-DGS2-316 , CAPACITY-30Cu.M/Hr@25MWC , SL NO:-AFT-560245,FWD-360251 b) Fitment and Alignment of pump with motor. Renewal of spider jaw copuling (qty-01) and all foundation nut and bolts (qty 04, M 20, Material -SS)

1012, EQPT:-BILGE AND GENERAL SERVICE PUMPS, MAKE-BE PUMPS MODEL-SH65-160MN1-DGS2-316 , CAPACITY-30Cu.M/Hr@25MWC , SL NO:-AFT-560245,FWD-360251 c) Suction and discharge pressure gauges to be renewed. Suction gauge Range -0.5 to 3 bar and discharge gauge reange 0 to 10 bar. The gauges should be glycerine filled.

1012, EQPT:-BILGE AND GENERAL SERVICE PUMPS, MAKE-BE PUMPS MODEL-SH65-160MN1-DGS2-316 , CAPACITY-30Cu.M/Hr@25MWC , SL NO:-AFT-560245,FWD-360251 d) Instrumentation gauges pipes (RMT- 02 mtrs) with suitable end fittings and isolating cock (qty-02) to be renewed. Mat: CuNi, Dia:1/4 inch.

1012, EQPT:-BILGE AND GENERAL SERVICE PUMPS, MAKE-BE PUMPS MODEL-SH65-160MN1-DGS2-316 , CAPACITY-30Cu.M/Hr@25MWC , SL NO:-AFT-560245,FWD-360251 e) Greasing cups of both pumps to be renewed

1012, EQPT:-BILGE AND GENERAL SERVICE PUMPS, MAKE-BE PUMPS MODEL-SH65-160MN1-DGS2-316 , CAPACITY-30Cu.M/Hr@25MWC , SL NO:-AFT-560245,FWD-360251 f) Pump coupling guard ((U shape, mesh type, with end plate Material -MS, thickness 2 mm) to be renewed, Gaurd Full Length 35 cm, width- 10 cm.

1013, EQPT:-FIRE AND GENERAL SERVICE PUMPS,MAKE-BE PUMPS,MODEL-A7130KK-DGS2-316-MS3 , CAPACITY-30Cu.M/Hr@40MWC, SL NO:-AFT-360248,FWD-360246 ( Firm Not To Quote )

1013, EQPT:-FIRE AND GENERAL SERVICE PUMPS,MAKE-BE PUMPS,MODEL-A7130KK-DGS2-316-MS3 , CAPACITY-30Cu.M/Hr@40MWC, SL NO:-AFT-360248,FWD-360246 a) Overhaul the pump completely and prove for satisfactory operation (Working pressure -6 Bar) . Overhaul shall include renewal of impeller, bearings, mechanical seal and shaft key.

1013, EQPT:-FIRE AND GENERAL SERVICE PUMPS,MAKE-BE PUMPS,MODEL-A7130KK-DGS2-316-MS3 , CAPACITY-30Cu.M/Hr@40MWC, SL NO:-AFT-360248,FWD-360246 b) Fitment and Alignment of pump with motor. Renewal of spider jaw copuling (qty-01) and all foundation nut and bolts (qty 04, M 20, Material -SS)

1013, EQPT:-FIRE AND GENERAL SERVICE PUMPS,MAKE-BE PUMPS,MODEL-A7130KK-DGS2-316-MS3 , CAPACITY-30Cu.M/Hr@40MWC, SL NO:-AFT-360248,FWD-360246 c) Suction and discharge pressure gauges to be renewed. Suction gauge Range -0.5 to 3 bar and discharge gauge reange 0 to 10 bar. The gauges should be glycerine filled.

1013, EQPT:-FIRE AND GENERAL SERVICE PUMPS,MAKE-BE PUMPS,MODEL-A7130KK-DGS2-316-MS3 , CAPACITY-30Cu.M/Hr@40MWC, SL NO:-AFT-360248,FWD-360246 d) Instrumentation gauges pipes (RMT- 02 mtrs) with suitable end fittings and isolating cock (qty-02) to be renewed. Mat: CuNi, Dia:1/4 inch.

1013, EQPT:-FIRE AND GENERAL SERVICE PUMPS,MAKE-BE PUMPS,MODEL-A7130KK-DGS2-316-MS3 , CAPACITY-30Cu.M/Hr@40MWC, SL NO:-AFT-360248,FWD-360246 e) Greasing cups of both pumps to be renewed

1013, EQPT:-FIRE AND GENERAL SERVICE PUMPS,MAKE-BE PUMPS,MODEL-A7130KK-DGS2-316-MS3 , CAPACITY-30Cu.M/Hr@40MWC, SL NO:-AFT-360248,FWD-360246 f) Pump coupling guard ((U shape, mesh type, with end plate Material -MS, thickness 2 mm)) to be renewed, Gaurd Full Length 35 cm, width- 10 cm.

1014, EQPT:-FRESH WATER PUMPS, MAKE-BE PUMPS, MODEL-A03110K-DGS2-316-MS3 , CAPACITY-02Cu.M/Hr@25MWC,SL NO:-AFT-356636,FWD-359937 ( Firm Not To Quote )

1014, EQPT:-FRESH WATER PUMPS, MAKE-BE PUMPS, MODEL-A03110K-DGS2-316-MS3 , CAPACITY-02Cu.M/Hr@25MWC,SL NO:-AFT-356636,FWD-359937 a) Overhaul the pump completely and prove for satisfactory operation (Working pressure -2 Bar) . Overhaul shall include renewal of bearings, mechanical seal.

1014, EQPT:-FRESH WATER PUMPS, MAKE-BE PUMPS, MODEL-A03110K-DGS2-316-MS3 , CAPACITY-02Cu.M/Hr@25MWC,SL NO:-AFT-356636,FWD-359937 b) Fitment and Alignment of pump with motor. Renewal of spider jaw copuling (qty-01 each) and all foundation nut and bolts (qty 04, M 20, Material -SS)

1014, EQPT:-FRESH WATER PUMPS, MAKE-BE PUMPS, MODEL-A03110K-DGS2-316-MS3 , CAPACITY-02Cu.M/Hr@25MWC,SL NO:-AFT-356636,FWD-359937 c) Suction and discharge pressure gauges to be renewed. Suction gauge Range -0.5 to 3 bar and discharge gauge reange 0 to 05 bar. The gauges should be glycerine filled.

1014, EQPT:-FRESH WATER PUMPS, MAKE-BE PUMPS, MODEL-A03110K-DGS2-316-MS3 , CAPACITY-02Cu.M/Hr@25MWC,SL NO:-AFT-356636,FWD-359937 d) Instrumentation gauges pipes (RMT- 02 mtrs) with suitable end fittings and isolating cock (qty-02) to be renewed. Mat: CuNi, Dia:1/4 inch.

1014, EQPT:-FRESH WATER PUMPS, MAKE-BE PUMPS, MODEL-A03110K-DGS2-316-MS3 , CAPACITY-02Cu.M/Hr@25MWC,SL NO:-AFT-356636,FWD-359937 e) Greasing cups of both pumps to be renewed

1014, EQPT:-FRESH WATER PUMPS, MAKE-BE PUMPS, MODEL-A03110K-DGS2-316-MS3 , CAPACITY-02Cu.M/Hr@25MWC,SL NO:-AFT-356636,FWD-359937 f) Pump coupling guard ((U shape, mesh type, with end plate Material -MS, thickness 2 mm) to be renewed, Gaurd Full Length 35 cm, width- 10 cm.

1015, EQPT:-DOMESTIC S/W PUMPS,MAKE-BE PUMPS,MODEL-A03110K-DGS2-316-MS3 , CAPACITY-02Cu.M/Hr@25MWC,SL NO:-AFT-359941,FWD-359940 ( Firm Not To Quote )

1015, EQPT:-DOMESTIC S/W PUMPS,MAKE-BE PUMPS,MODEL-A03110K-DGS2-316-MS3 , CAPACITY-02Cu.M/Hr@25MWC,SL NO:-AFT-359941,FWD-359940 a) Overhaul the pump completely and prove for satisfactory operation (Working pressure -2 Bar) . Overhaul shall include renewal of shaft, impeller, bearings, mechanical seal and shaft key

1015, EQPT:-DOMESTIC S/W PUMPS,MAKE-BE PUMPS,MODEL-A03110K-DGS2-316-MS3 , CAPACITY-02Cu.M/Hr@25MWC,SL NO:-AFT-359941,FWD-359940 b) Fitment and Alignment of pump with motor. Renewal of spider jaw copuling (qty-01) and all foundation nut and bolts (qty 04, M 20, Material -SS)

1015, EQPT:-DOMESTIC S/W PUMPS,MAKE-BE PUMPS,MODEL-A03110K-DGS2-316-MS3 , CAPACITY-02Cu.M/Hr@25MWC,SL NO:-AFT-359941,FWD-359940 c) Suction and discharge pressure gauges to be renewed. Suction gauge Range -0.5 to 3 bar and discharge gauge reange 0 to 05 bar. The gauges should be glycerine filled.

1015, EQPT:-DOMESTIC S/W PUMPS,MAKE-BE PUMPS,MODEL-A03110K-DGS2-316-MS3 , CAPACITY-02Cu.M/Hr@25MWC,SL NO:-AFT-359941,FWD-359940 d) Instrumentation gauges pipes (RMT- 02 mtrs) with suitable end fittings and isolating cock (qty-02) to be renewed. Mat: CuNi, Dia:1/4 inch.

1015, EQPT:-DOMESTIC S/W PUMPS,MAKE-BE PUMPS,MODEL-A03110K-DGS2-316-MS3 , CAPACITY-02Cu.M/Hr@25MWC,SL NO:-AFT-359941,FWD-359940 e) Greasing cups of both pumps to be renewed

1015, EQPT:-DOMESTIC S/W PUMPS,MAKE-BE PUMPS,MODEL-A03110K-DGS2-316-MS3 , CAPACITY-02Cu.M/Hr@25MWC,SL NO:-AFT-359941,FWD-359940 f) Pump coupling guard ((U shape, mesh type, with end plate Material -MS, thickness 2 mm) to be renewed, Gaurd Full Length 35 cm, width- 10 cm.

1016, EQPT:- SRP S/W PUMPS, MAKE-BE PUMPS, Model:- A03620K-DGS2-316, Type - Centrifugal , CAPACITY-02Cu.M/Hr, ( Firm Not To Quote )

1016, EQPT:- SRP S/W PUMPS, MAKE-BE PUMPS, Model:- A03620K-DGS2-316, Type - Centrifugal , CAPACITY-02Cu.M/Hr a) Overhaul the pump completely and prove for satisfactory operation (Working pressure -2 Bar) . Overhaul shall include renewal of impeller, bearings.

1016, EQPT:- SRP S/W PUMPS, MAKE-BE PUMPS, Model:- A03620K-DGS2-316, Type - Centrifugal , CAPACITY-02Cu.M/Hr b) Fitment and Alignment of pump with motor. Renewal of spider jaw copuling (qty-01) and all foundation nut and bolts (qty 04, M 20, Material -SS)

1016, EQPT:- SRP S/W PUMPS, MAKE-BE PUMPS, Model:- A03620K-DGS2-316, Type - Centrifugal , CAPACITY-02Cu.M/Hr c) Suction and discharge pressure gauges to be renewed. Suction gauge Range -0.5 to 3 bar and discharge gauge reange 0 to 05 bar. The gauges should be glycerine filled.

1016, EQPT:- SRP S/W PUMPS, MAKE-BE PUMPS, Model:- A03620K-DGS2-316, Type - Centrifugal , CAPACITY-02Cu.M/Hr d) Instrumentation gauges pipes (RMT- 01 mtrs) with suitable end fittings and isolating cock (qty-02) to be renewed. Mat: CuNi, Dia:1/4 inch.

1016, EQPT:- SRP S/W PUMPS, MAKE-BE PUMPS, Model:- A03620K-DGS2-316, Type - Centrifugal , CAPACITY-02Cu.M/Hr e) Pump coupling guard ((U shape, mesh type, with end plate Material -MS, thickness 2 mm) to be renewed, Gaurd Full Length 35 cm, width- 10 cm.

1017, EQPT:- EXTERNAL FI FI PUMP,MAKE-CMA ENGINEERING SINGAPORE LTD, MODEL-FD 125X100-500,TYPE-MAIN ENGINE DRIVEN CENTRIFUGAL PUMP,CAPACITY-150Cu.M/Hr@120MWC@1800 RPM, SL NO:-PORT-8584,STBD-8586 ( Firm Not To Quote )

1017, EQPT:- EXTERNAL FI FI PUMP,MAKE-CMA ENGINEERING SINGAPORE LTD, MODEL-FD 125X100-500,TYPE-MAIN ENGINE DRIVEN CENTRIFUGAL PUMP,CAPACITY-150Cu.M/Hr@120MWC@1800 RPM, SL NO:-PORT-8584,STBD-8586 a) Complete Overhauling of the pump and prove for satisfactory operation. Renew mechanical seals, bearings.

1017, EQPT:- EXTERNAL FI FI PUMP,MAKE-CMA ENGINEERING SINGAPORE LTD, MODEL-FD 125X100-500,TYPE-MAIN ENGINE DRIVEN CENTRIFUGAL PUMP,CAPACITY-150Cu.M/Hr@120MWC@1800 RPM, SL NO:-PORT-8584,STBD-8586 b) Casing to be inspected and checked for pitting. Metal buildup to be carried out. followed by surface finishing, if deep pits existing.

1017, EQPT:- EXTERNAL FI FI PUMP,MAKE-CMA ENGINEERING SINGAPORE LTD, MODEL-FD 125X100-500,TYPE-MAIN ENGINE DRIVEN CENTRIFUGAL PUMP,CAPACITY-150Cu.M/Hr@120MWC@1800 RPM, SL NO:-PORT-8584,STBD-8586 c) Suction and discharge pressure gauges to be renewed. Suction gauge Range -0.5 to 3 bar and discharge gauge reange 0 to 15 bar. The gauges should be glycerine filled.

1017, EQPT:- EXTERNAL FI FI PUMP,MAKE-CMA ENGINEERING SINGAPORE LTD, MODEL-FD 125X100-500,TYPE-MAIN ENGINE DRIVEN CENTRIFUGAL PUMP,CAPACITY-150Cu.M/Hr@120MWC@1800 RPM, SL NO:-PORT-8584,STBD-8586 d) Instrumentation gauges pipes (RMT- 02 mtrs) with suitable end fittings and isolating cock (qty-02) to be renewed. Mat: CuNi, Dia:1/4 inch.

1018, EQPT:- EXTERNAL FI FI PUMP POWER TAKE OFF ASSEMBLY, MAKE-DONG-I INDUSTRIL CO LTD, MODEL- DPO 087 - D, SPEED: 600-3000, REDUCTION RATIO :- 1:0.85 ( Firm Not To Quote )

1018, EQPT:- EXTERNAL FI FI PUMP POWER TAKE OFF ASSEMBLY, MAKE-DONG-I INDUSTRIL CO LTD, MODEL- DPO 087 - D, SPEED: 600-3000, REDUCTION RATIO :- 1:0.85 a) Complete Overhauling of power take off assembly to be carried out and prove for satisfactory operation.

1019, EQPT/SYSTEM: FOAM SYSTEM/ FOAM GUNS ( Firm Not To Quote )

1019, EQPT/SYSTEM: FOAM SYSTEM/ FOAM GUNS a) Foam guns to be removed chemically cleaned and painted (red).

1019, EQPT/SYSTEM: FOAM SYSTEM/ FOAM GUNS b) All perished rubber fittings (40 mm dia, 5 mm thick) to be renewed.

1019, EQPT/SYSTEM: FOAM SYSTEM/ FOAM GUNS c) Foam gun drive gearboxes to be overhauled for free movement.

1019, EQPT/SYSTEM: FOAM SYSTEM/ FOAM GUNS d) Foam tank isolating valves to be overhauled 50mm SDNR (GM)

1019, EQPT/SYSTEM: FOAM SYSTEM/ FOAM GUNS e) Worm gear assembly to be dismantled cleaned and fitted back.

1019, EQPT/SYSTEM: FOAM SYSTEM/ FOAM GUNS f) Couplings shaft locking pins (dia 05 mm,10 mm long) to be renewed.

1019, EQPT/SYSTEM: FOAM SYSTEM/ FOAM GUNS g) Three way flushing valve to be overhauled 50mm

1019, EQPT/SYSTEM: FOAM SYSTEM/ FOAM GUNS h) Overhaul of foam system propotionator to be carried out

1019, EQPT/SYSTEM: FOAM SYSTEM/ FOAM GUNS J) post overhauling Performance of foam guns to be undertaken :- Water throws >60 Mtrs@ 12 Bar Pressure @1800 Rpm.

1020, EQPT/SYSTEM: CO2 EXTINGUISHING SYSTEM, MAKE: TYCO FIRE SECURITY AND SERVICE PVT (Firm Not To Quote)

1020, EQPT/SYSTEM: CO2 EXTINGUISHING SYSTEM, MAKE: TYCO FIRE SECURITY AND SERVICE PVT a) All CO2 cylinders to be removed and weighed in place, / CO2 level to be checked ,recharged with 45kg CO2 each

1020, EQPT/SYSTEM: CO2 EXTINGUISHING SYSTEM, MAKE: TYCO FIRE SECURITY AND SERVICE PVT b) CO2 discharge nozzles to be opened, checked for chockages, cleaned and fitted back

1020, EQPT/SYSTEM: CO2 EXTINGUISHING SYSTEM, MAKE: TYCO FIRE SECURITY AND SERVICE PVT c) Complete drenching system piping to be blown through using HP air to prove system free of blockages

1020, EQPT/SYSTEM: CO2 EXTINGUISHING SYSTEM, MAKE: TYCO FIRE SECURITY AND SERVICE PVT d) All CO2 cylinders (45 kg capacty) and system pipes to be painted as per coding post work completion.

1020, EQPT/SYSTEM: CO2 EXTINGUISHING SYSTEM, MAKE: TYCO FIRE SECURITY AND SERVICE PVT e) All system pipes (dia-20 mm) to be painted as per coding post work completion.

1021, EQPT/SYSTEM: VALVES ( Firm Not To Quote ) Following valves to be overhauled and pressure tested.Testing pressure:-S/W Systrm-9 kg/cm2,Air System-45 kg/cm2,F/W System-5 kg/cm2. NOTE :-Overhauling of valves includes renewal of valve spindle,valve disc,gland.

1021, EQPT/SYSTEM: VALVES a) 100mm valves, Type - SD, Material- Gun Metal

1021, EQPT/SYSTEM: VALVES b) 80mm valves, Type - SDNR, Material- Gun Metal

1021, EQPT/SYSTEM: VALVES c) 65mm Valves, Type - SDNR, Material- Gun Metal

1021, EQPT/SYSTEM: VALVES d) 50mm Valves, Type - SD, Material- Bronze

1021, EQPT/SYSTEM: VALVES e) 40mm Valves, Type - Gate, Material- Bronze

1021, EQPT/SYSTEM: VALVES f) 40mm Valves, Type - SDNR, Material- Bronze

1021, EQPT/SYSTEM: VALVES g) 32mm valve,Type-Niddle,Material-Bronze,Make-Harshad eng

1021, EQPT/SYSTEM: VALVES h) 32mm Valves, Type - Gate, Material- Bronze

1021, EQPT/SYSTEM: VALVES j) 20 mm Valves, Type-Gate, Material-Gun Metal

1021, EQPT/SYSTEM: VALVES k) 20mm Valves,Type-SD,Matrial-Gun Metal

1021, EQPT/SYSTEM: VALVES l) 20mm valve,Type-Needle,Material-Bronze,Make-Harshad eng

1021, EQPT/SYSTEM: VALVES m) 12mm , Type - Gate, Material- Gun Metal

1021, EQPT/SYSTEM: VALVES n) 15mm Valves,Type-Globe ,Material-Gun Metal

1022, EQPT/SYSTEM: SYSTEM PIPES FOR CHEMICAL CLEANING Following system pipes to be removed, chemically cleaned , pressure tested and post fitment painted as per colour code. ( Firm Not To Quote )

1022, EQPT/SYSTEM: SYSTEM PIPES FOR CHEMICAL CLEANING a) 110mm external FF line,Mat:-CuNi

1022, EQPT/SYSTEM: SYSTEM PIPES FOR CHEMICAL CLEANING b) 200 mm main sea chest pipe.Mat-CuNi

1022, EQPT/SYSTEM: SYSTEM PIPES FOR CHEMICAL CLEANING c) 80mm Pipe Sea water system pipe Mat: CuNi

1022, EQPT/SYSTEM: SYSTEM PIPES FOR CHEMICAL CLEANING d) 100mm Sea water system pipe Mat: CuNi

1022, EQPT/SYSTEM: SYSTEM PIPES FOR CHEMICAL CLEANING e) 60mm Sea water system pipe Mat: GI

1022, EQPT/SYSTEM: SYSTEM PIPES FOR CHEMICAL CLEANING f) 50mm system pipe Mat: CuNi

1022, EQPT/SYSTEM: SYSTEM PIPES FOR CHEMICAL CLEANING g) 35mm system pipes Mat: Seemless Copper

1022, EQPT/SYSTEM: SYSTEM PIPES FOR CHEMICAL CLEANING h) 40 mm fuel system pipe Mat: Stailess Steel

1022, EQPT/SYSTEM: SYSTEM PIPES FOR CHEMICAL CLEANING j) 25 mm system pipe Mat: Staineless Steel

1022, EQPT/SYSTEM: SYSTEM PIPES FOR CHEMICAL CLEANING k) 20mm system pipe,Mat:-Stainless Steel

1023, EQPT/SYSTEM: SYSTEM PIPES FOR RENEWAL Renewal of pipes includes manufacturing of end flange as per sample. ( Firm Not To Quote )

1023, EQPT/SYSTEM: SYSTEM PIPES FOR RENEWAL a) 110mm external FF line,Mat:-CuNi

1023, EQPT/SYSTEM: SYSTEM PIPES FOR RENEWAL b) 200 mm main sea chest pipe.Mat-CuNi

1023, EQPT/SYSTEM: SYSTEM PIPES FOR RENEWAL c) 80mm Pipe Sea water system pipe Mat: CuNi

1023, EQPT/SYSTEM: SYSTEM PIPES FOR RENEWAL d) 100mm Sea water system pipe Mat: CuNi

1023, EQPT/SYSTEM: SYSTEM PIPES FOR RENEWAL e) 60mm Sea water system pipe Mat: GI

1023, EQPT/SYSTEM: SYSTEM PIPES FOR RENEWAL f) 50mm system pipe Mat: CuNi

1023, EQPT/SYSTEM: SYSTEM PIPES FOR RENEWAL g) 35mm system pipes Mat: Seemless Copper

1023, EQPT/SYSTEM: SYSTEM PIPES FOR RENEWAL h) 40 mm fuel system pipe Mat: Stailess Steel

1023, EQPT/SYSTEM: SYSTEM PIPES FOR RENEWAL j) 25 mm system pipe Mat: Staineless Steel

1023, EQPT/SYSTEM: SYSTEM PIPES FOR RENEWAL k) 20mm system pipe,Mat:-Stainless Steel

1024, EQPT/SYSTEM:BUTTERFLY VALVE Following butterfly valve to be overhauled.Ovehauling includes renewal of Rubber Sheet/Valves.Make-RK ( Firm Not To Quote )

1024, EQPT/SYSTEM:BUTTERFLY VALVE a) Butterfly valve,Dia-250mm

1024, EQPT/SYSTEM:BUTTERFLY VALVE b) Butterfly valve,Dia-125mm

1024, EQPT/SYSTEM:BUTTERFLY VALVE c) Butterfly valve,Dia-100mm

1024, EQPT/SYSTEM:BUTTERFLY VALVE d) Butterfly valve,Dia-80mm

1024, EQPT/SYSTEM:BUTTERFLY VALVE e) Butterfly valve,Dia-60mm

1025, BILGE PLATFORM ( Firm Not To Quote )

1025, BILGE PLATFORM a) Engine Room and SRP compartment bilge platform to be removed, cleaned and fitback to facilate bilge area work.

1025, BILGE PLATFORM b) Renew bilge platform plates . Material- aluminium chequred plates, thickness- 05 mm, rubber beading between frames and bilge plates to be placed, during repair of bilge frames.

1025, BILGE PLATFORM c) SRP compartment - New bilge paltform plates to be placed in the area between both HRP systems,

1025, BILGE PLATFORM d) brackets / angle plates ( Mat MS) for securing bilge plates to be welded.and plates to be secured by SS nuts.

1026, EQPT:REDUCER Following reducer to be removed overhauled,renewed wear down parts and fitted back after calibration as per limits.( Firm Not To Quote )

1026, EQPT:REDUCER a) Reducer,Dia 32mm

1026, EQPT:REDUCER b) Reducer,Dia 20mm

1026, EQPT:REDUCER c) Reducer,dia-40mm

1027, EQPT:STRAINER Following strainer to be manufactured as per sample,Material-Brass,Thickness-3.0mm, Hole dia-5.0mm,Distance between hole to hole-3.0mm ( Firm Not To Quote )

1027, EQPT:STRAINER a) Strainer,Dia-80mm

1027, EQPT:STRAINER b) Strainer,Dia-200mm

1028, EQPT: DD Non Submersible Salvage Pump MAKE : Modi, Model- M 120 NM, Capacity- 333 LPM ( Firm Not To Quote )

1028, EQPT: DD Non Submersible Salvage Pump MAKE : Modi, Model- M 120 NM, Capacity- 333 LPM a) Engine and pump to be completely overhauled , and proved for satisfactory performance post work completion

1028, EQPT: DD Non Submersible Salvage Pump MAKE : Modi, Model- M 120 NM, Capacity- 333 LPM b) Discharge side canvas flexible hoses to be renewed (dia- 65mm, length- 25 meter). Pump to be proved for satisfactory performance post work completion.

1029, EQPT: AIR SYSTEM RESERVOIRS a) Air reservoirs to be removed chemically cleaned and pressure tested.

1029, EQPT: AIR SYSTEM RESERVOIRS b) Air reservoir system valves ( filling, outlet, drain and relief) to be removed overhauled and pressure tested up to 45 kg/cm2 .size 25 mm. globe.

1029, EQPT: AIR SYSTEM RESERVOIRS c) Reservoir Pressure guages to be renewed. (Range 0-50 kg)

1030, MISCELLANEOUS: a) Main Engine (CAT C 32 ACERT ) Heat Exchanger (spare) along with plates found defective to be renewed. Model no 225124, Sl no. 2521787.

1030, MISCELLANEOUS: b) Submersible pump not takng suction to be ovrhauled. Pump to be proved for satisfactory performance post work completion.( MAKE : Mode, Model- M504,NM,Capacity- 40 TPH)

1030, MISCELLANEOUS: c) Portable pumps of capacity 2 HP to be procured and placed at suitble positions onboard for transffering of fuels / lub oils in case of emergency. (stand by for LO and Fuel Transfer PPs)

1030, MISCELLANEOUS: d) Expansion Tank caps to be manufactured as per sample,. Mat Al

1031, Emergency cooling connection to Main Engines from general service sea water system, Job involves Manufacturing of 02 T pieces(50 mm) with flanges and piping length of 05 mtrs,(dia (50mm) and 02 screw down valves of 2''. location a convinient by ED Team / SS, Mat : Bronge for flanges, Cuni for pipes, Gunmetal for valves

1032, Emergency cooling connection to DGs cooling water system from general service sea water system, Job involves Manufacturing of 02 T pieces(30 mm) with flanges and piping length of 05 mtrs,(dia (30mm) and 02 screw down valves of 2''. location a convinient by ED Team / SS, Mat : Bronge for flanges, Cuni for pipes, Gunmetal for valves

ELECTRICAL WORK PACKAGE General:All electrical power components / spares like contactors, overload relays, etc are to to be sourced from Navy approved vendors. (Firm Not To Quote IMPORTANT NOTE:- Following points are applicable for all relevant DL's and shipyards/Firms to consider and quote accordingly. (a) Renewal of Items / Spares:- (i) Renewal of items / spares wherever mentioned in the QDL to be undertaken by shipyard / firm as per the sample / drawing / details provided by SS / COA / RMT. (ii) Shipyard / Firm should undertake the routines / overhaul of the equipment including the mandatory spares required for undertaking the same, irrespective of the spares mentioned in the mandatory spares list provided by ND(V). (iii) Further, the cost should include the degutting of existing item, supply of new item, fitment and proving of the system post renewal.(Firm Not To Quote)

The definition of overhaul of motor includes the following:- (a) Dismantle the motor. The motor has to be dismantled and landed by Yard for overhauling. (b) Undertake trueness checks of rotor on the lathe. Repair observed Defects (c) Check for ovality in bearing housing. Repair observed Defects. (d) Clean the rotor and stator thoroughly with alcohol, air, varnish and bake. There should be no dust particles or other foreign particles observed after cleaning (e) Measure the insulation of windings of rotor and stator. In case insulation is below one mega ohm rewind the rotor / stator (f) Replace heater and thermistor units. (g) Assemble the motor with new bearings (h) In case of repairs to shaft trueness or replaced of winding,undertake dynamic balancing of the rotor (j) Check and rectify phase imbalance in insulation of windings (k) Undertake test bed Trials and confirm no load starting and running currents, speed, SPM readings apart from other standard checks. SPM reading are to be in green zone post overhaul. (l) All motors and machinery body/ cabinets to be painted as per the original colur. (m) Brass Marking talleys to be provided for all equipment( 8x2 cms)- Qty 1500 nos apprx total. (n) Wiring/ cabling which are removed during gutting/ degutting to be re wired whereever applicable. (p) All motors with monoblock pumps are to be proved in situ. (q) All terminal boxes rubber beading to be replaced to achieve water tight integrity.(Firm Not To Quote)

The definition of overhaul of Starter includes the following:- (a) Dismantle the starter. The starter has to be dismantled and landed by Yard for overhauling. (b) Disconnect & Remove all components & wiring. (c) Mechanical cleaning of starter panel board,welded/repaires of any damages to the body/door hinges & painted with one cote of primer and two coat of powder coating (original colour) d) cleaning of all connections,internal components with cleaning agents. e)calibration of OLRs./Timer relays. f)rifixing all components & given the all internal connections g)check the circuitary functionality & rectify if any fault. h) check the insulation between the phases,phase to body & improve the insulation if it is less than 5M ohms .i)refixed in onboard & given the all connections. j)Take load trails after give the power supply.

The definition of overhaul of control panels includes the following:- (a) Dismantle the control panal. The control panel has to be dismantled and landed by Yard for overhauling. (b) Disconnect & Remove all components & wiring. (c) Mechanical cleaning of control panel board,welded/repaires of any damages to the body/door hinges & painted with one cote of primer and two coat of powder coating (original colour) d) cleaning of all connections,internal components with cleaning agents. e)calibration of OLRs,Timer relays. f)calibration of PCBs,sensors,diod rectifiers&etc. g)rifixing all components & given the all internal connections h)check the circuitary functionality & rectify if any fault. i) check the insulation between the phases,phase to body & improve the insulation if it is less than 5M ohms j)refixed in onboard & given the all connections. k)Take load trails after give the power supply.

Following 'As Fitted' drawings need to be prepared and handed over to ships staff (a) Foundations of new equipment (b) Electrical cabling (c) All As and A's including internals of control panel (Hull, Engineering & Electrical). (d) ABER replacement (Hull, Engineering & Electrical ).(Firm Not To Quote)

2001 : Eqpt/System: MAIN SWITCH BOARD Make : L & T, RATING: 415V,3PH,50HZ Located in E/R 01 no Switch board with two 3 Ph bus bar systemcoupled with buscoupler breaker 125A with three incomeing feedrs from two DAs. & shore supply And these three are electrically interlocked & connected to the commen bus bar in swbd. Make L&T Firm Not To Quote

2001 : Eqpt/System: MAIN SWITCH BOARD (a) MSB to be overhauled (includes defective switches to be renwed, indiacation lamp to be renewed,perished control wiring to be renewed with crimping of proper lugs, marking sleeves to be put on control wiring and loose wirng to be tied with cable ties)

2001 : Eqpt/System: MAIN SWITCH BOARD (b) Renewal of LED indication lamps fittings of different colors (Red 10, Yellow 10, Blue 05, Green 10, White10, Amber05) 230V

2001 : Eqpt/System: MAIN SWITCH BOARD (C ) Renewal of following MCCB and power contactor(Firm Not To Quote)

2001 : Eqpt/System: MAIN SWITCH BOARD (C )(i) Make : L & T, Model : DN2-250N, Rating 125A 3 Pole, Release type : Thermal Magnetic, Aux Contact : 1, Trip Alarm Contact : 1TAC, Shunt Release : 240V AC,

2001 : Eqpt/System: MAIN SWITCH BOARD 1 (C ) (ii) Make : L & T, Model : DN0-100C, Rating 100A 3 Pole, Release type : Thermal Magnetic, Aux Contact : 1, Trip Alarm Contact : 1TAC, Shunt Release : 240V AC,

2001 Eqpt/System: MAIN SWITCH BOARD (C )(iii) Power contactor, Make : L & T, Model : MNX10, Basic contact : 2NO+2NC, Coil Voltage : 230V AC

2001 : Eqpt/System: MAIN SWITCH BOARD (d)Check & Calibrate all parameters of Insulation Monitoring Relay. Make:Selco, Model:T3200

2001 : Eqpt/System: MAIN SWITCH BOARD (d)(i) Renew Insulation Monitoring Relay. Make:Selco, Model:T3200

2001 : Eqpt/System: MAIN SWITCH BOARD (e)(i)Operating parameters of Insulating monitoring Relay (a) Voltage Tolarance :+10-20% of Un, b) Power Consumption :2VA max, (c) Frequency Range :45 - 65Hz (d) Operating Temperature Range :-20+70ºC (e) Contact rating :AC 2A,380V,250VA & DC110V,2A, 150W f) Dielectric test :2500V,50Hz,(g) Presetting 0-5M Ohm (h) Accuracy signal :± 5%(of preset valve) (i) Instrument scale 0-5 M ohm (j) Instrument Resistance Max 100 Ohm (Firm Not To Quote)

2001 : Eqpt/System: MAIN SWITCH BOARD (f) Renewal of following meters (Firm Not To Quote)

2001 : Eqpt/System: MAIN SWITCH BOARD (f) (i) Ammeter : 415V AC, with moving coil Rect scale :240, Input Mode CT operated, CT ratio 150/5A, Accuracy class 1, Range 0-150A, Red Mark at 104A, Size : 96x96mm, Gasket Required

2001 : Eqpt/System: MAIN SWITCH BOARD (f) (ii) KW meter : with moving coil Rect scale :240, Input voltage 415V AC, Syatem : 3 wire 2 element, Input current : 5A, Range 0-75KW, Red Mark at 60KW, Size : 96x96mm,Gasket Required

2001 : Eqpt/System: MAIN SWITCH BOARD (f) (iii) Frequency Meter : Input voltage415VAC, Analog type, scale :240, Accuracy class 1, Range 45-50-55Hz Size : 96x96mm, Gasket Required.

2001 : Eqpt/System: MAIN SWITCH BOARD (g) check & calibrate all parameters of the synchroscope relay (Make:L&T,model:MB100) along with double scale voltmeter, double scale frequncy meter and prove parallaling operation of both generators

2001 : Eqpt/System: MAIN SWITCH BOARD (h) Rubber mat : Insulating Rubber Mat deteriorated. To be Renewed with high voltage Electrical rubber mat in front of MSB.(Thickness- 3mm) Make : vardhaman, model : class c

2002 Eqpt/System: Control Panels The following Control Panels are to be over hauled, defctive components to be replaced with new one & made them operational. (Firm Not To Quote)

2002 Eqpt/System: Control Panels (a) Oily Bilge Water Seperator System Control Panel 415V,3Ph,50Hz, 1 HP. Complete overhaul to be carried out, defecive parts to be replaced and prove it for satisfectory performance.Make:Blohm +Voss industries (singapoor)Pvt Ltd, 33,Benoi road,Pioneer Lot,Singapore-627784 . phn-(65) 6-268 8882, [email protected]/[email protected].

2002 Eqpt/System: Control Panels (b) Anchor windlass control panel including master controller 415V,3Ph,50Hz, 15HP .Size:17.5mm Dia Chain; Make: Hemant Engineering Works

2002 Eqpt/System: Control Panels (C) Eqpt/System: Capstain Motor Control Panel along with Remote Control panel (01 in wheel house and 01 in QTR deck) 415V,3Ph,50Hz, 15HP Make:Hemant Engineering

2002 Eqpt/System: Control Panels (d)LUB OIL CENTRIFUGE control panel 415V,3Ph,50Hz, 2 HP Make: Alfa LevelWorks

2002 Eqpt/System: Control Panels ( e ) FUEL OIL CENTRIFUGE control panel, 415V,3Ph,50Hz, 2 HP Make: Alfa LevelWorks (panel door hinges refitted/changing to required the door to open as anti clock wise presently it was opening in clock wise in the view of maintance work)

2003 Eqpt/System: Window Wiper Systems Make Speich s.r.l.a socio; Motor data- Make:Suntrans enterprise AC 230V AC 0.1HP;3500RPM; (Firm Not To Quote)

2003 Eqpt/System: Window Wiper Systems Make Speich s.r.l.a socio; Motor data- Make:Suntrans enterprise AC 230V AC 0.1HP;3500RPM (a) Overhaul the gear system and prove them for free movement / satisfactory performance.

2003 Eqpt/System: Window Wiper Systems Make Speich s.r.l.a socio; Motor data- Make:Suntrans enterprise AC 230V AC 0.1HP;3500RPM (b) Overhaul the Motors(window wifer) and prove them for free movement / satisfactory performance.

2003 Eqpt/System: Window Wiper Systems Make Speich s.r.l.a socio; Motor data- Make:Suntrans enterprise AC 230V AC 0.1HP;3500RPM (c) FW system line to be proved (dia10 mm, cu-Ni)

2003 Eqpt/System: Window Wiper Systems Make Speich s.r.l.a socio; Motor data- Make:Suntrans enterprise AC 230V AC 0.1HP;3500RPM (d ) Renew the Blades Including Rubber coambing

2003 Eqpt/System: Window Wiper Systems Make Speich s.r.l.a socio; Motor data- Make:Suntrans enterprise AC 230V AC 0.1HP;3500RPM (e) Machinery body to be Cleaned to bare metal and painted with one cote of primer and two coat of enamil paint .

2004 Eqpt/System: Navigational Lighting Power supply and alarm modules (230V AC & 24V DC) Make:L&T Carryout routines mentioned below and prove them for satisfactory performance (Firm Not To Quote)

2004 Eqpt/System: Navigational Lighting Power supply and alarm modules (230V AC & 24V DC) Make:L&T (a) Check the functions of all fuse units-40nos,control cards (fault detection moduels)-20nos, indication lamps-40nos & horn-1no.

2004 Eqpt/System: Navigational Lighting Power supply and alarm modules (230V AC & 24V DC) Make:L&T (b) If deffective repair them

2004 Eqpt/System: Navigational Lighting Power supply and alarm modules (230V AC & 24V DC) Make:L&T (c ) Check and repair the control cards and prove for satisfactory performance

2004 Eqpt/System: Navigational Lighting Power supply and alarm modules (230V AC & 24V DC) Make:L&T (d) Renew the LED indication lamps with holders

2004 Eqpt/System: Navigational Lighting Power supply and alarm modules (230V AC & 24V DC) Make:L&T (e ) Renew the Fuse Units in clip on type connectors

2004 Eqpt/System: Navigational Lighting Power supply and alarm modules (230V AC & 24V DC) Make:L&T (f) Renew the cables ( single core cable, 2 mm sq) (incoming & outgoing) if they are perished.

2004 Eqpt/System: Navigational Lighting Power supply and alarm modules (230V AC & 24V DC) Make:L&T (g) Renew the control cards (fault detection modules) 230V,AC 5 nos,24V DC -5nos

2005 Eqpt/System:Navigational Light fittings. (Firm Not To Quote)

2005 Eqpt/System:Navigational Light fittings. (a) Overhauling the Navigational Light Fittings(AC & DC) Make:M/S Arvin Industries 230V for AC,24V for DC -(Two tier set) .

2005 Eqpt/System:Navigational Light fittings. (b) Renew the incoming cable 2core,1sq.mm,Length-.10mtr for each fitting from JBs to light fitting-10Nos fittings

2005 Eqpt/System:Navigational Light fittings. (c ) Renew the AC navigational bulbs 230V,60w

2005 Eqpt/System:Navigational Light fittings. (d) Renew the DC navigational bulbs 24V,60w

2005 Eqpt/System:Navigational Light fittings. (e ) Provide the LED Marine navigational light fittings (Operating voltage range12V to 26V DC) water proof IP66 as spares.Red-4nos,Green-4nos,white-6

2006 Follwing Light Fittings corroded, to be renewed: (Firm Not To Quote)

2006 (a) Renew Watertight U Glass light fitting incandescent lamp fittings. 230V,18W LED light fittings, Make- Sysca

2006 (b) Renew the 230V,18W LED lights , Make- Sysca

2006 (c ) Renew Flush mounting Type indoor 230V,LED light fittings, Make- Sysca

2006 (d) Renew the 230V, 20W,LED light fittings, Make- Sysca

2006 (e ) Repair and overhaul Watertight searchlight fittings 30cm Dia with 1000W lamp with w/h cat no 351A

2006 (f) Renew the flood light LED lamp fittings 100W,230V AC Make:Sysca

2007 EQPT/SYSTEM: CO2 EXTINGUISHING SYSTEM MAKE: TYCO FIRE SECURITY AND SERVICE PVT LTD.(Firm Not To Quote)

2007 EQPT/SYSTEM: CO2 EXTINGUISHING SYSTEM MAKE: TYCO FIRE SECURITY AND SERVICE PVT LTD.( (a) Carryout complete overhaul and prove them for satisfactory performance as per bellow (Firm not to Quote)

2007 EQPT/SYSTEM: CO2 EXTINGUISHING SYSTEM MAKE: TYCO FIRE SECURITY AND SERVICE PVT LTD. (b) Overhaul the Motorised Siren & Flasher Make:KHERAJ Type-Horozontal Single Mounting,24V,DC,75W 6000RPM,Range 800mtrs .

2007 EQPT/SYSTEM: CO2 EXTINGUISHING SYSTEM MAKE: TYCO FIRE SECURITY AND SERVICE PVT LTD. (c ) Alaram panel system-1 no,limit switches-4nos,sensors-4nos and relays-6nos to be checked,calibrated to be proved for satisfactory operation

2007 EQPT/SYSTEM: CO2 EXTINGUISHING SYSTEM MAKE: TYCO FIRE SECURITY AND SERVICE PVT LTD.( (d) Check ,calibrate & set to their set point of Heat Detectors-4Nos, Type Nittan uk ns-DhG1 set point 58°C,

2007 EQPT/SYSTEM: CO2 EXTINGUISHING SYSTEM MAKE: TYCO FIRE SECURITY AND SERVICE PVT LTD.( (e ) Check ,calibrate & set to their set point of Pressure operated switch-1no Make:Ginger Kerr Working pressure 3-150bar

2007 EQPT/SYSTEM: CO2 EXTINGUISHING SYSTEM MAKE: TYCO FIRE SECURITY AND SERVICE PVT LTD.( (f) Machinery body to be Cleaned to bare metal and painted with one coat of primer and two coat of enamil paint(originol colour)

2007 EQPT/SYSTEM: CO2 EXTINGUISHING SYSTEM MAKE: TYCO FIRE SECURITY AND SERVICE PVT LTD. (g) Renew the indication lamps with holders (2.5 cm dia cover)

2007 EQPT/SYSTEM: CO2 EXTINGUISHING SYSTEM MAKE: TYCO FIRE SECURITY AND SERVICE PVT LTD. (h) Renew the all rubber packings

2007 EQPT/SYSTEM: CO2 EXTINGUISHING SYSTEM MAKE: TYCO FIRE SECURITY AND SERVICE PVT LTD. (i) Renew the PCB and relay fitted in side box

2007 EQPT/SYSTEM: CO2 EXTINGUISHING SYSTEM MAKE: TYCO FIRE SECURITY AND SERVICE PVT LTD. (j) continuty & functionality check for cabling for heat detectors-4nos,siren 7 flasher & etc

2007 EQPT/SYSTEM: CO2 EXTINGUISHING SYSTEM MAKE: TYCO FIRE SECURITY AND SERVICE PVT LTD. (j) Provethe system for Satifcatory performance

2008 Eqpt/System: Shore Supply Box. Make:L&T,100amps,415V,3ph (Firm Not To Quote)

2008 Eqpt/System: Shore Supply Box. Make:L&T,100amps,415V,3ph (a)Carryout routines mentioned below and prove them for satisfactory performance

2008 Eqpt/System: Shore Supply Box. Make:L&T,100amps,415V,3ph (b) Renew the indication lamps with holders

2008 Eqpt/System: Shore Supply Box. Make:L&T,100amps,415V,3ph (c ) Control fuse base with carrier including 4A fuse

2008 Eqpt/System: Shore Supply Box. Make:L&T,100amps,415V,3ph (d) Renewal of Hand operated MCCB-100amps with machanical interlocking for phase changeover system, hand operated, Make: L&T, Model : DN2-250N, 3pole

2008 Eqpt/System: Shore Supply Box. Make:L&T,100amps,415V,3ph (e ) Mechanical cleaning of supply panel board & painted with one cote of primer and two coat of powder coating (original colour)

2008 Eqpt/System: Shore Supply Box. Make:L&T,100amps,415V,3ph (f) Renewal of Phase Sequence Indicator with arrow mark rotating indicator. 415V 3Phase, 50 Hz

2008 Eqpt/System: Shore Supply Box. Make:L&T,100amps,415V,3ph (g) Renewal of shore suppply cable 3x25 sqmm, rubber insulated, Copper multi stranded wire marine cable with terminals are to be lugging (lug hole size 20mm dia)

2009 Eqpt/System: Lead Acid Batteries. Make:Exide,180AH,12V (Firm Not To Quote)

2009 Eqpt/System: Lead Acid Batteries. Make:Exide,180AH,12V (a) Renew the maintenance free battery 180AH 12V Make:Exide.

2009 Eqpt/System: Lead Acid Batteries. Make:Exide,180AH,12V (b) Clean & Tighten the all connections with proper lugs, ferrules & connecters

2009 Eqpt/System: Lead Acid Batteries. Make:Exide,180AH,12V (c ) Renew the Battery connectors

2009 Eqpt/System: Lead Acid Batteries. Make:Exide,180AH,12V (d) Renew the Short link cable (50sq.mm multi stand copper cables,Length 0.5mtr ) connectors

2009 Eqpt/System: Lead Acid Batteries. Make:Exide,180AH,12V (e ) Renew the Parallel link cable connectors in emergency batteries bank

2010 Eqpt/System:Broadcast system Make:Philips,Type:VRC-10M-50 /A100K10070 (Firm Not To Quote)

2010 Eqpt/System:Broadcast system Make:Philips,Type:VRC-10M-50 /A100K10070 (a) Main broad cast system causing frequent problem to be renewed along with its speaker. Renew all call back station. No of speaker:- 10, No of call back station - 03,no of micro phones-3nos,

2010 Eqpt/System:Broadcast system Make:Philips,Type:VRC-10M-50 /A100K10070 (b) cabling to be renewed from amplifier to speakers

2011 Eqpt/System: Float Level Switches .Make:B.K.Equipments. Repair & calibrate the float level switches & prove them for satisfactory performance for their respective circuits for the following Level Switches (Firm Not To Quote)

2011 Eqpt/System: Float Level Switches (a) Fresh Water Daily serviceTank (Gravitational) at monky deck (High level-1no, Low level-1 no)-2 Nos

2011 Eqpt/System: Float Level Switches (b) Fuel oil daily servise(FODS) tanks (2 Nos for port & stbd) low level switches-1No for each tank

2011 Eqpt/System: Float Level Switches (c ) Lub oil Tank in engine room (High level-1no,Low level-1no)-2 Nos

2011 Eqpt/System: Float Level Switches (d) Dirty oil Tank in engine room (High level-1no)-1 no

2011 Eqpt/System: Float Level Switches (e ) Engine room bilge high level-2Nos

2011 Eqpt/System: Float Level Switches (f) Clean & Tighten the all connections with proper lugs, ferrules & connecters

2011 Eqpt/System: Float Level Switches (g)Check the cable continuty between main panel to junction box and junction box to level switches,

2011 Eqpt/System: Float Level Switches (h) replace wiring if found perished, .

2012 Eqpt/System: Batteries Accomadation Boxes (Wooden) (Firm Not To Quote)

2012 Eqpt/System: Batteries Accomadation Boxes (a) Renew the complete box with 12mm Hylam sheet/High quality ply wood sheet,Clean & painted the boxes as mentioned below

2012 Eqpt/System: Batteries Accomadation Boxes (b) 2 in Batteries (180AH,12V) are placed in each box & these boxes are adjusted to acomidated below bilge plates in E/R including opening bilge plate doors to be provided for battery maintance purpose.

2012 Eqpt/System: Batteries Accomadation Boxes (c ) 4 in nos Batteries (180AH12V) are accomodated in 4 sections of one box at 01 deck.

2013 Non W/T on/off Switches 6A,240V Make:Commercial, Renew the switches and connect in circuits and proove them for satisfactory performance

2014 Metal Clad W/T DP on/off Switche sockets 16A,415V Make:LEC. Renew the switches and connect in circuits and proove them for satisfactory performance

2015 Metal Clad W/T DP on/off Switche sockets 16A,240V Make:LEC. Renew the switches and connect in circuits and proove them for satisfactory performance

2016 Non W/T Switche Sockets 6A,240V Make:Commercial Renew the switches and connect in circuits and proove them for satisfactory performance

2017 Non W/T Switche Sockets 16A,240V Make:Commercial Renew the switches and connect in circuits and proove them for satisfactory performance

2018 Eqpt/System: Wall mounted Electrical fans (Oscillating) Make:C&G, Type- 400 mm Sweep: Renew the fans fitted at various places and prove them for satisfactory performance

2019 Eqpt/System: Submersible Pump & Its Starter, Make :- Mody, Capacity 20 TPH. (Firm Not To Quote)

2019 Eqpt/System: Submersible Pump & Its Starter, Make :- Mody, Capacity 20 TPH (a) Carryout complete overhaul routines and prove them for satisfactory performance / Made operational

2019 Eqpt/System: Submersible Pump & Its Starter, Make :- Mody, Capacity 20 TPH (b) Renew the OLRs,/SPPs/Timers/MCBs as per their ratings if deffective replace them

2019 Eqpt/System: Submersible Pump & Its Starter, Make :- Mody, Capacity 20 TPH (c ) Replace fuse units.

2019 Eqpt/System: Submersible Pump & Its Starter, Make :- Mody, Capacity 20 TPH (d) Renew the Neoprene Rubber Gasket for water tight purpose-for door

2020 Eqpt/System: Battery chargering Units, Make:L & T, Input;415V, 3ph, 50Hz. Out put 24V 63A DC (1.5KW-1no,0.5KW-1Nos), & 1.5KW charger input 230V, 50Hz, output 50V/24V DC 63A (Firm Not To Quote)

2020 Eqpt/System: Battery chargering Units, Make:L & T, Input;415V, 3ph, 50Hz. Out put 24V 63A DC (1.5KW-1no,0.5KW-1Nos), & 1.5KW charger input 230V, 50Hz, output 50V/24V DC 63A (a) One in no1.5kw 1ph 230V AC as input & 50V/24V,DC as out put charger unit to be renewed ( Along with make neccesary cabling work to be done) and to be made operational

2020 Eqpt/System: Battery chargering Units, Make:L & T, Input;415V, 3ph, 50Hz. Out put 24V 63A DC (1.5KW-1no,0.5KW-1Nos), & 1.5KW charger input 230V, 50Hz, output 50V/24V DC 63A (b) Carryout complete overhaul routines and prove them for satisfactory performance of battery chargers 1.5KW

2021 Eqpt/System: Call Bell Unit 24V,DC; Make:Lite shine Electricals(Firm Not To Quote)

2021 Eqpt/System: Call Bell Unit 24V,DC; Make:Lite shine Electricals (a) Carryout complete overhaul routines and prove them for satisfactory performance.

2021 Eqpt/System: Call Bell Unit 24V,DC; Make:Lite shine Electricals (b) Renew the Push buttons

2021 Eqpt/System: Call Bell Unit 24V,DC; Make:Lite shine Electricals (c ) Renew the indication lamp with holder (2.5 cm dia cap)

2022 Eqpt/System: Transformers 415V to 220V,50Hz,3Ph 15KVA(Firm Not To Quote)

2022 Eqpt/System: Transformers 415V to 220V,50Hz,3Ph 15KVA (a) Carryout complete overhaul routines and prove them for satisfactory performance / Made operational.

2023 Eqpt/System:Motors Over hauling: carry out complete over hauling of the following motors and prove for satisfactory operation. (total 31 Nos) Only ZZ standard bearing (SKF/FAG) is to be used.(Firm Not To Quote).

2023 Eqpt/System:Motors Over hauling (a) Engine room supply fan motors 415v,3ph,50Hz,5HP,

2023 Eqpt/System:Motors Over hauling (b) Engine room Exaust fan motor 415v,3ph,50Hz 5HP,

2023 Eqpt/System:Motors Over hauling (c ) Galley exhaust fan motors 415v,3phase,50Hz,1HP

2023 Eqpt/System:Motors Over hauling (d) Galley supply fan motors 415v,3phase,50Hz,1HP

2023 Eqpt/System:Motors Over hauling (e )CO2 room exhaust fan motors 415v, 3phase, 50Hz,1HP

2023 Eqpt/System:Motors Over hauling (f) Toilet Exhaust fan motor 415v, 3phase, 50Hz,0.5HP

2023 Eqpt/System:Motors Over hauling (g) Lub Oil Tansfer pump motor 415v,3ph,50Hz,1.5HP

2023 Eqpt/System:Motors Over hauling (h) Bilge and ballast pump motor 415v,3ph,50Hz,7.5HP

2023 Eqpt/System:Motors Over hauling (j) Fire and GS pump motor 415v,3ph,50Hz,7.5HP

2023 Eqpt/System:Motors Over hauling (k) Fuel Oil Transfor Pump Motor. 415v,3ph,50Hz,1.5HP,

2023 Eqpt/System:Motors Over hauling (m) Accomodation Supply Fan motor 415v,3ph,50Hz,1.5 HP

2023 Eqpt/System:Motors Over hauling (n) Dirty oil pump motor 415v,3ph,50Hz,1HP,

2023 Eqpt/System:Motors Over hauling (p) Domestic Sea Water Pump motor 415v,3ph,50Hz,1HP

2023 Eqpt/System:Motors Over hauling (q)Domestic Fresh Water Pump motor 415v,3ph,50Hz,1HP

2023 Eqpt/System:Motors Over hauling (r ) SRP cooling pump motor 415v,3ph,50Hz,2HP,

2023 Eqpt/System:Motors Over hauling (s) HP Air Compressor Motor 415v,3ph,50Hz,2HP,

2023 Eqpt/System:Motors Over hauling (t) CVC motor, 230V, 1Phase, 50Hz, 0.25HP

2023 Eqpt/System:Motors Over hauling (u) srp supply blower motor

2023 Eqpt/System:Motors Over hauling (v) wind wifer motors 230V,0.1HP,3500RPM

2024 Eqpt/System: Starters Make:L & T, Rating 415V,3Ph,50Hz Carryout compleat overhaul of following starters/group starter control panel and proove them for satisfactory performance (Firm Not To Quote).

2024 Eqpt/System: Starters Make:L & T, Rating 415V,3Ph,50Hz (a) Bilge and ballast pump group control panel STAR -DELTA (2x7.5HP)

2024 Eqpt/System: Starters Make:L & T, Rating 415V,3Ph,50Hz (b) Fire and GS pump group control panel STAR -DELTA (2x7.5HP)

2024 Eqpt/System: Starters Make:L & T, Rating 415V,3Ph,50Hz (c ) Engine room supply fan starter STAR -DELTA (5HP)

2024 Eqpt/System: Starters Make:L & T, Rating 415V,3Ph,50Hz (d) Engine room Exhaust fan starter STAR -DELTA (5HP)

2024 Eqpt/System: Starters Make:L & T, Rating 415V,3Ph,50Hz (e ) Toilet Exhaust fan starter DOL (0.5HP)

2024 Eqpt/System: Starters Make:L & T, Rating 415V,3Ph,50Hz (f) Fuel Oil Transfor Pump Group control panel (2x1.5 HP)

2024 Eqpt/System: Starters Make:L & T, Rating 415V,3Ph,50Hz (g) Lube Oil Transfer pump Group control panel (2x1HP)

2024 Eqpt/System: Starters Make:L & T, Rating 415V,3Ph,50Hz (h) Dirty oil pump DOL starter 1HP

2024 Eqpt/System: Starters Make:L & T, Rating 415V,3Ph,50Hz (j) Domestic Sea Water Pump Group control panel DOL (2x1HP)

024 Eqpt/System: Starters Make:L & T, Rating 415V,3Ph,50Hz (k) Domestic Fresh Water Pump Group control panel DOL (2x1HP)

2024 Eqpt/System: Starters Make:L & T, Rating 415V,3Ph,50Hz (m) SRP cooling pump DOL starter 415v,3ph,50Hz,2HP

2024 Eqpt/System: Starters Make:L & T, Rating 415V,3Ph,50Hz (n) Accomodation Supply Fan DOL starter 1.5 HP

2024 Eqpt/System: Starters Make:L & T, Rating 415V,3Ph,50Hz (p) Air compressor control panal

2024 Eqpt/System: Starters Make:L & T, Rating 415V,3Ph,50Hz (q) Renew the Neoprene Rubber Gasket for water tight purpose-for all doors

2024 Eqpt/System: Starters Make:L & T, Rating 415V,3Ph,50Hz (r )Renewal of following : (Firm Not To Quote)

2024 Eqpt/System: Starters Make:L & T, Rating 415V,3Ph,50Hz r(i) Power Contactor, Make : L & T, Model : MNX18, coil voltage 230V AC, with Add ON 2NO+2NC contacts

2024 Eqpt/System: Starters Make:L & T, Rating 415V,3Ph,50Hz r(ii) Thermal Overload Relay, Rating : 415V, 3pole. Rating 1.4-2.3A

2024 Eqpt/System: Starters Make:L & T, Rating 415V,3Ph,50Hz r(iii) Thermal Overload Relay, Rating : 415V, 3pole. Rating 2.0-3.3A

2024 Eqpt/System: Starters Make:L & T, Rating 415V,3Ph,50Hz r(iv) Thermal Overload Relay, Rating : 415V, 3pole. Rating 3-5A

2024 Eqpt/System: Starters Make:L & T, Rating 415V,3Ph,50Hz r(v) Thermal Overload Relay, Rating : 415V, 3pole. Rating 0.9-1.5A

2024 Eqpt/System: Starters Make:L & T, Rating 415V,3Ph,50Hz r(vi) Thermal Overload Relay, Rating : 415V, 3pole. Rating 4.5-7.5A

2024 Eqpt/System: Starters Make:L & T, Rating 415V,3Ph,50Hz r(vii) Voltage Monitoring Relay. Aux supply 415V AC, ralay contacts - 2, Auto Reset, Make : Minilec, Model : VCTD2

2024 Eqpt/System: Starters Make:L & T, Rating 415V,3Ph,50Hz r(viii) FN Switch, switch fuse disconnector, 3 pole, 63A, aux contact : 1NO+1NC. Make : L&T, Model : FN63

2024 Eqpt/System: Starters Make:L & T, Rating 415V,3Ph,50Hz r (ix) Timer : Star delta timer, aux supply 240V AC, Time range 120sec, Cut off contacts 2, Make : L&T GIC, Model : 20SDT0

2024 Eqpt/System: Starters Make:L & T, Rating 415V,3Ph,50Hz r(x) Power Contactor, Make :Shneider, Model : AWG10-18,CU 75C⁰, coil voltage 230V AC, with Aux contacts 2NO+2NC

2025: Eqpt:Electrical horn 24V DC, MEGASONIK Renew the Marine Electrical Horn (Dual trumpet electric horn ,100% Stainleass Steel housing,304 non magnetic grade with rust proof bright polished finish for using exterior in salt water environment 24V DC, DB level 120dB) fitted at mast pole including

2026: EQPT/SYSTEM: Foam Fire Gun Motor, Make: Rotor Overhauling of foam gun motors, Rating 415V, 3Ph, 50Hz, 0.5HP along with limit switches/sensors and its control panel (including two in nos joystick panel)

2026: EQPT/SYSTEM: Foam Fire Gun Motor, Make: Rotor Overhaul the Solenoid valves 230V AC for remote Fog/jet operation

2027 Opening of panel Doors DC distribution panel door & anchor wind loss doors are not acceess to fully opened.These panel are Readjusting for fully openig the doors.

2028 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02(Carried out by OEM only)(Firm Not To Quote)

2028 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 (a) Carry out the compleat overhoul of Control panel system,limit switches,sensors and relays to be checked,rectification of faults calibrated & to be proved for satisfactory operation. (Exluding following DL nos2028(a1) to 2028(a8))

2028 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 (a1) Calibrate the hydraulic oil pressure sensor.

2028 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 (a2) Calibrate the hydraulic oil temp sensor

2028 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 (a3) Calibrate the hydraulic oil low level sensor

2028 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 (a4) Calibrate the hydraulic oil to low level sensor

2028 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 (a5) Calibrate the hydraulic oil clogged sensor

2028 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 (a6) Calibrate the Clutch oil pressure sensor.

2028 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 (a7) Calibrate the Clutch oil temp sensor

2028 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 (a8) Calibrate the Clutch oil level sensor

2028 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 (b) provide & fitted the key switch with 6 pole ON/OFF rotary type door mounted model in port & stbd W/H consol panels.

2028 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 (c ) Renew & laying the 2 in nos 15X2.5sq.mm multisatnd copper marine cables from HRP control panels (port & Stbd) to W/H consols(Port & Stbd) connected in circuits for the purpose of isolate the power supply to HRP panels when ship is in darken. (i.e tug is not in use)

2028 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 (d) Renew the thrust pcb control cards(model no 73.OO.OO25.OO)-2nos,Steering PCB control cards(MODEL NO:73.OO.OOO2.OO)-2nos

2028 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 (e ) Renew the clutch solenoids 24V DC,

2028 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 (f) Renew the clutch oil pressure switch working pressure up to 40bar,operating 15bar & 13bar 24V DC ,

2028 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 (g) Renew the clutch oil level switch 24V DC.

2028 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 (g1) Repair/servicing the clutch oil level switch 24V DC.

2028 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 (h) Renew the clutch oil temperature switch 24V DC.

2028 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 (h1) Repair/servicing the clutch oil temperature switch 24V DC.

2028 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 (i) Renew the hydraulic oil pressure sensor

2028 EQPT/SYSTEM: STEERING RUDDER PROPELLER(SRP) MAKE: HRP THRUSTER SYSTEM,HOLLAND, MODEL- HRP4000,SL NO:-STBD-10918-04-2011-01,PORT-10918-04-2011-02 (J) Renew the Clutch oil pressure sensor

2029 EQPT : MAIN ENGINES Electrical Control System MAKE : CATERPILLER, MODEL-C32,SL NO:-PORT-RN401211,STBD-RN401209,MAX OUTPUT-850BHP@1800RPM (Carried out by OEM only) (Firm Not To Quote)

2029 EQPT : MAIN ENGINES Electrical Control System MAKE : CATERPILLER, MODEL-C32,SL NO:-PORT-RN401211,STBD-RN401209,MAX OUTPUT-850BHP@1800RPM (a) Control panel system,pressure switches,sensors and relays to be checked,rectification of faults,calibrated & to be proved for satisfactory operation. (exluding following Dl no 2029(b) to 2029 (l)

2029 EQPT : MAIN ENGINES Electrical Control System MAKE : CATERPILLER, MODEL-C32,SL NO:-PORT-RN401211,STBD-RN401209,MAX OUTPUT-850BHP@1800RPM (b) Calibrate starting air pressure sensor (part no 377-0263)

2029 EQPT : MAIN ENGINES Electrical Control System MAKE : CATERPILLER, MODEL-C32,SL NO:-PORT-RN401211,STBD-RN401209,MAX OUTPUT-850BHP@1800RPM (c ) Calibrate speed sensor (part no 279-9828)

2029 EQPT : MAIN ENGINES Electrical Control System MAKE : CATERPILLER, MODEL-C32,SL NO:-PORT-RN401211,STBD-RN401209,MAX OUTPUT-850BHP@1800RPM ( d) Calibrate sea water sensor (part no 377-0263)

2029 EQPT : MAIN ENGINES Electrical Control System MAKE : CATERPILLER, MODEL-C32,SL NO:-PORT-RN401211,STBD-RN401209,MAX OUTPUT-850BHP@1800RPM (e ) Calibrate fuel oil pressure sensor (part no 274-6719) 2nos for each engine

2029 EQPT : MAIN ENGINES Electrical Control System MAKE : CATERPILLER, MODEL-C32,SL NO:-PORT-RN401211,STBD-RN401209,MAX OUTPUT-850BHP@1800RPM (f) Calibrate fuel oil temperature sensor (part no 274-7395) 1no for each engine

2029 EQPT : MAIN ENGINES Electrical Control System MAKE : CATERPILLER, MODEL-C32,SL NO:-PORT-RN401211,STBD-RN401209,MAX OUTPUT-850BHP@1800RPM (g) Calibrate air temperature sensor (part no 288-3783) 1no for each engine

2029 EQPT : MAIN ENGINES Electrical Control System MAKE : CATERPILLER, MODEL-C32,SL NO:-PORT-RN401211,STBD-RN401209,MAX OUTPUT-850BHP@1800RPM (h) Calibrate exaust temperature sensor (part no 280-9910) 2 nos for each engine

2029 EQPT : MAIN ENGINES Electrical Control System MAKE : CATERPILLER, MODEL-C32,SL NO:-PORT-RN401211,STBD-RN401209,MAX OUTPUT-850BHP@1800RPM (i) Calibrate air intake pressure sensor (part no 274-6721) 1no

2029 EQPT : MAIN ENGINES Electrical Control System MAKE : CATERPILLER, MODEL-C32,SL NO:-PORT-RN401211,STBD-RN401209,MAX OUTPUT-850BHP@1800RPM (j) Calibrate coolent liqued level sensor (part no 204-2518),2nos

2029 EQPT : MAIN ENGINES Electrical Control System MAKE : CATERPILLER, MODEL-C32,SL NO:-PORT-RN401211,STBD-RN401209,MAX OUTPUT-850BHP@1800RPM (k) Calibrate Temperature sensors for coolent,engine oil,air intake (part no 288-3783) 3nos

2029 EQPT : MAIN ENGINES Electrical Control System MAKE : CATERPILLER, MODEL-C32,SL NO:-PORT-RN401211,STBD-RN401209,MAX OUTPUT-850BHP@1800RPM (l) Calibrate Engine oil pressure sensor (part no 274-6719) 1nos for each engine

2029 EQPT : MAIN ENGINES Electrical Control System MAKE : CATERPILLER, MODEL-C32,SL NO:-PORT-RN401211,STBD-RN401209,MAX OUTPUT-850BHP@1800RPM (m) Renew the air pressure sensors (part no 377-0263)

2029 EQPT : MAIN ENGINES Electrical Control System MAKE : CATERPILLER, MODEL-C32,SL NO:-PORT-RN401211,STBD-RN401209,MAX OUTPUT-850BHP@1800RPM (n) Renew the fuel oil pressure sensors (part no 274-6719)

2029 EQPT : MAIN ENGINES Electrical Control System MAKE : CATERPILLER, MODEL-C32,SL NO:-PORT-RN401211,STBD-RN401209,MAX OUTPUT-850BHP@1800RPM (o) Renew the speed sensor (part no 279-9828)

2029 EQPT : MAIN ENGINES Electrical Control System MAKE : CATERPILLER, MODEL-C32,SL NO:-PORT-RN401211,STBD-RN401209,MAX OUTPUT-850BHP@1800RPM (p)Renew the temperature sensor (part no 274-7395)

2029 EQPT : MAIN ENGINES Electrical Control System MAKE : CATERPILLER, MODEL-C32,SL NO:-PORT-RN401211,STBD-RN401209,MAX OUTPUT-850BHP@1800RPM (q)Renew the temperature sensor (part no 288-3783)

2029 EQPT : MAIN ENGINES Electrical Control System MAKE : CATERPILLER, MODEL-C32,SL NO:-PORT-RN401211,STBD-RN401209,MAX OUTPUT-850BHP@1800RPM (r)Renew the temperature sensor (part no 274-7395)

2029 EQPT : MAIN ENGINES Electrical Control System MAKE : CATERPILLER, MODEL-C32,SL NO:-PORT-RN401211,STBD-RN401209,MAX OUTPUT-850BHP@1800RPM (s) Renew the Emergency switch in M/E control panels (OEM part no 109-6507)

2029 EQPT : MAIN ENGINES Electrical Control System MAKE : CATERPILLER, MODEL-C32,SL NO:-PORT-RN401211,STBD-RN401209,MAX OUTPUT-850BHP@1800RPM (t ) Provide the suitable 2 pole On/OFF control switch for power supply control from battery sources.

2030 EQPT : DG Primemover (ENGINES) Electrical Control System MAKE : Kirloskar oil india ltd, MODEL-6R 1080 T, SL NO:-Fwd6H9495 1100804,Aft-6H9496 1100805,OUT PUT-127BHP@1500RPM (Carried out by OEM only) (routine may be carried out with assistance of OEM or authorised Rep) (Firm Not To Quote)

2030 EQPT : DG Primemover (ENGINES) Electrical Control System MAKE : Kirloskar oil india ltd, MODEL-6R 1080 T, SL NO:-Fwd6H9495 1100804,Aft-6H9496 1100805,OUT PUT-127BHP@1500RPM (a) Control panel system,pressure switches,sensers and relays to be checked,rectification of faults,calibrated & to be proved for satisfactory operation

2030 EQPT : DG Primemover (ENGINES) Electrical Control System MAKE : Kirloskar oil india ltd, MODEL-6R 1080 T, SL NO:-Fwd6H9495 1100804,Aft-6H9496 1100805,OUT PUT-127BHP@1500RPM (b) Renew the Fresh water temperature sensors 24V Dc

2030 EQPT : DG Primemover (ENGINES) Electrical Control System MAKE : Kirloskar oil india ltd, MODEL-6R 1080 T, SL NO:-Fwd6H9495 1100804,Aft-6H9496 1100805,OUT PUT-127BHP@1500RPM (c ) Overauling the Engine self starting motors.24V,DC

2030 EQPT : DG Primemover (ENGINES) Electrical Control System MAKE : Kirloskar oil india ltd, MODEL-6R 1080 T, SL NO:-Fwd6H9495 1100804,Aft-6H9496 1100805,OUT PUT-127BHP@1500RPM (d) Overauling the Engine driven battery charger alternator .24V,DC

2031 Eqpt/System: Generators/Alternator Make:Stamford,415V,3Ph,75KVA,50Hz,1500RPM Carryout routines mentioned below and prove them for satisfactory performance.(routine may be carried out with assistance of OEM or authorised Rep).(Firm Not To Quote)

2031 Eqpt/System: Generators/Alternator Make:Stamford,415V,3Ph,75KVA,50Hz,1500RPM (a)overhaul the generators/alternator

2031 Eqpt/System: Generators/Alternator Make:Stamford,415V,3Ph,75KVA,50Hz,1500RPM (b) Check the insulation of Alternator with 500V Megger. The insulation resistance should not be less than 2 mega ohm. If less isolate the system and improve the insulation. Check inductance and capacitance of the alternator winding.

2031 Eqpt/System: Generators/Alternator Make:Stamford,415V,3Ph,75KVA,50Hz,1500RPM (c ) Rewind alternator if insulation found below specific limit and inductance and capacitance value of winding found imbalance or winding found open circuit.

2031 Eqpt/System: Generators/Alternator Make:Stamford,415V,3Ph,75KVA,50Hz,1500RPM (d) Carryout varnishing of rotor and stator winding.

2031 Eqpt/System: Generators/Alternator Make:Stamford,415V,3Ph,75KVA,50Hz,1500RPM (e ) Carryout balancing of rotor.

2031 Eqpt/System: Generators/Alternator Make:Stamford,415V,3Ph,75KVA,50Hz,1500RPM (f) Inspection of Lugs, clean the lugs with zero paper and replace if damaged.

2031 Eqpt/System: Generators/Alternator Make:Stamford,415V,3Ph,75KVA,50Hz,1500RPM (g) Check the condition of all sealing of the alternators, repaired if required.

2031 Eqpt/System: Generators/Alternator Make:Stamford,415V,3Ph,75KVA,50Hz,1500RPM1 (h) Check the rotating rectifier assembly for any loose connection and check proper connection.

2031 Eqpt/System: Generators/Alternator Make:Stamford,415V,3Ph,75KVA,50Hz,1500RPM (j) Take SPM reading of DE/NDE bearing of alternators; carry out greasing by grease gun if required (yellow zone).

2031 Eqpt/System: Generators/Alternator Make:Stamford,415V,3Ph,75KVA,50Hz,1500RPM (k) BQ for change of bearings (DE & NDE Bearings) in case of existing bearings are in red zone.

2031 Eqpt/System: Generators/Alternator Make:Stamford,415V,3Ph,75KVA,50Hz,1500RPM (k) Carryout alignment of Alternator and AVR

2031 Eqpt/System: Generators/Alternator Make:Stamford,415V,3Ph,75KVA,50Hz,1500RPM (k) Renew the AVR (Aumatic Voltage Regulator) Model:MX 321

2032 DG Load trails Post repair/routines. Trials to be conducted as per details/ regimes mentioned below. Observations / Defects observed to be liquidated and Trials to be reconducted. Post completion of the routines/overhaul, the machinery should be proved to rated/designed power / capacity without limitations/observations and vibration levels at all points should be less than 5 mm/sec. The equipment performance will be considered satisfactory only if it the performance trials are cleared by Naval Inspection Agency. SPM readings of generator to be in green zone. Stable supply for communication, navigation and survey equipment to be proved under total power failure condition. &Required to satisfy the following points.

2032 DG Load trails (a) Insulation of Generator Rotor and Starter to be 10M Ohm (b) Frequency Range to be 49.5 - 50.5 (c )Rate of change of frequency permissble limit is 0.2 - 0.4 Hz/sec (d) Drop values limit is 3.5 - 4% (e ) Peak variation of frequency to be 0-100%, 50-75%, 75-100%, 100-75% and 100-0% (f) 02 sec recovery should be at all regimes (g) Peak variation of voltage recovery to be in 01 sec for all regimes. (h)Difference between average of 3 line RMS value wrt Normal at 100% load to be proved.(j) M-Load trial to be offered. (k)Overvoltage and Undervoltage protection to be proved. l) prove for parallal operation by shifting of load form one to another generator.(Firm Not To Quote)

2033 Eqpt/System: Industrial compact Shelwing .(Firm Not To Quote)

Provided theRolling cum locking Compact storage shelving of dimensions7in nos of 2' Length X 10' width X 8' Hight (All are to be required to interlocked).

2034 Eqpt/System: Spares The following spares to be required to supplied. (Firm Not To Quote)

2034 Eqpt/System: Spares (a) Heating Elements 1500W,440V,"U" shaped,9mm internal dia,1mm thickness copper pipe,710mm in length (i.etotal length of element if straited is 1700mm)

2034 Eqpt/System: Spares (b) Relays Make:RELECO,Model: C9-A41-24DX, 14pins,24V DC.

2034 Eqpt/System: Spares (c ) Relay sockets,Make:RELECO,Model:S9-M Relay socket,Din Rail,Screw,14Pins

2034 Eqpt/System: Spares (d) Relays Make:RELECO,Model: Mk2P-l AC220V.8Pins coil General purpose only. 14pins,24V DC.

2034 Eqpt/System: Spares (e ) Relay sockets,Make:RELECO,Model:S2B+S2BC Relay socket,Din Rail,Screw,8Pins

2034 Eqpt/System: Spares (f) OVER VOLTAGE RELAY CONTRACTOR WITH 2NO+2NC.

2034 Eqpt/System: Spares (g) Auto-Recovery voltage protective device,Model:VPD2-63.

2034 Eqpt/System: Spares (h) Electrical hand gloves Flexible .

2035 Eqpt/System:split A/Cs Renew & installing the 6 in nos spilt A/Cs at acommidation Rooms-2nos, ( 1.5Tons), Master cabin-1no(1Ton),Eng.cabin-1no(1Ton),Dining room-1no(1Ton),& W/H- 1nos(1.5Ton).Total-1.5Ton-3nos,1Ton-3Nos (the job included the gutting & regutting,laying of cabling)

2035 Eqpt/System:split A/Cs (a) Renew the 1 in no Delta/Delta transformer 20KVA input3Ph,415V,50Hz & out put 3Ph,230V,50Hz (installation,conections & prove satisfactory operation)

2035 Eqpt/System:split A/Cs (b) Renew & layin of 3X10sq.mm multi stant copper marine cable (from MSB to under W/H & Transformer to DB at under w/h.)

2035 Eqpt/System:split A/Cs (c ) Renew & laying of 3X6sq.mm multi stant copper marine cable (from DB at under W/H to various ac locations via switches for 7 in nos a/cs (i.e including 1 in no existing A/c in W/h)

2035 Eqpt/System:split A/Cs (d) Renew & install the 1 in no Mcb DB Which is required to have 10 in nos DP MCB 20A,2 nos TP 60A mcb,

2035 Eqpt/System:split A/Cs (e ) Renew the 7 in nos Ac sockets

2035 Eqpt/System:split A/Cs (f) Renew the 7 in nos Ac stebilisers

2035 Eqpt/System:split A/Cs (g) Servicing/overhauling of one in no 1.5 ton split A/C (presently it was working).

2036 Eqpt/System:Cooking Range(5KW) and Oven (3KW) (Firm Not To Quote)

2036 Eqpt/System:Cooking Range(5KW) and Oven (3KW) (a)Carry out compleat overhaul of cooking range system. a) dismantel all the parts b) thoroghly cleaning with cleaning agents(i.e alchohol / rust lick/ spirit),c) tighten the all connections,d) improve the insulation upto 5 M ohms if it was less insulation,e) renew the internal wiring if any wire found ferrished (presently there is no ferrished wires) f) Mechanical cleaning of supply panel board & painted with one cote of primer and two coat of powder coating (original colour),g) Assembled all the parts, h) given the power supply and prove for satisfactory operational

2036 Eqpt/System:Cooking Range(5KW) and Oven (3KW) (b) Renew the Heating elements 1.5kw,415V (M type)

2036 Eqpt/System:Cooking Range(5KW) and Oven (3KW) Re-placedof VHF (RF cable) from Antenna to VHF set

2037 Eqpt/System:Wind speed & Direction Indicator system.Make:Lilley & Gilliie ltd,Model:P1249,Voltage;24V DC(Firm not to Quote)

2037 Eqpt/System:Wind speed & Direction Indicator system.Make:Lilley & Gilliie ltd,Model:P1249,Voltage;24V DC (a) Carry out compleat overhaul & calibration of wind speed & Direction indicator along with accessory sub equipments like Wind Fan,cable & etc.

2038 Eqpt/System: V.H.F.Set Make:Sailor,Type:6222 VHF DSC (routine may be carried out with assistance of OEM or equivelent).

2038 Eqpt/System: V.H.F.Set (b) Carryout complete overhaul routines and prove them for satisfactory performance / Made operational

2038 Eqpt/System: V.H.F.Set ( c ) Calibrate the unit & test all the channels (HZs) & rectify if any deffect in VHF set

2038 Eqpt/System: V.H.F.Set (d) Renew the VHF set Antenna and it has to be fixed on its foundation properly at wheel house top

2038 Eqpt/System: V.H.F.Set ( e)Re-placedof VHF (RF cable) from Antenna to VHF set

2039 Eqpt/System: Echo sounder Make:KODEN , (routine may be carried out with assistance of OEM or equivelent).

2039 Eqpt/System: Echo sounder (a) Carryout complete overhaul routines and prove them for satisfactory performance / Made operational (presently it was working.)

Services (A) Docking and undocking charges (Both Versions)

(B) Dock blocks preparation & laying out as per docking plan

Dock hire charges for an estimated duration of 60 Days as per OCR

Wet basin/alongside hire charges for the remaining duration (i.e. total refit duration of – 60 days docking period)

Provision of sufficient lighting for duty staff

Quote for maintenance of two in no. fire lines for the refit duration .

Provision of two transports (cars) for entire refit duration (one for refit Co-ordinating staff and one for ND(V) monitoring Team) for 12 hrs or 100KM/day whichever is less

Provision of stationory / office items for ND(V) / Refit monitoring team for entire refit duration period. Cater budget of Rs 2000/- per month. Requirement will be intimated RMT/ NDV on as requirement basis. Payment at actuals. Note:- firms to quote.

Mail man services (02 Nos) for entire refit duration (one for user department and one for planning / Co-ordinating department ) to be provided for 10 Hrs per day

QC inspection for the entire scope of work by third party IRS/LRS/ABS/QC/TPI for the refit duration as per the QIS.

ME SPARES DL No 1001) FUEL FILTER Part No.1R0755

ME SPARES DL No 1001) LUB OIL FILTER part No.1R1808

ME SPARES DL No 1001) AIR FILTER Part No.207-7870

ME SPARES DL No 1001) AIR FILTER Part No.270-7257

ME SPARES DL No 1001) SEAL O RING part no.6V-5054

ME SPARES DL No 1001) ZIC ROD part No.6L-2280

ME SPARES DL No 1001) REGULATOR part No.248-5513

ME SPARES DL No 1001) SEAL part no.3S-9643

ME SPARES DL No 1001) SEAL part no.202-7530

ME SPARES DL No 1001) SEAL O RING part no.112-1102

ME SPARES DL No 1001) CLAMPS part no.8T-4984

ME SPARES DL No 1001) PLUG PIPE part no.3E-7428

ME SPARES DL No 1001) HOSE 16CM part no.5P-1262

ME SPARES DL No 1001) HOSE 13CM part no.5P-1262

ME SPARES DL No 1001) SEAL O RING part no.5F-3999

ME SPARES DL No 1001) SEAL O RING part no.231-4708

ME SPARES DL No 1001) SEAL O RING part no.109-0076

ME SPARES DL No 1001) SEAL O RING part no.6V-3250

ME SPARES DL No 1001) SEAL O RING part no.8T-1703

ME SPARES DL No 1001) SEAL O RING part no.6L-7817

ME SPARES DL No 1001) ELC PREMIX COOLANT part no.4692718

ME SPARES DL No 1001) AIR STARTING MOTOR (CAT) part no.3341529 / 382-9606

ME SPARES DL No 1001) SEAL FOR HEAT EXCHANGERS part no.202-7530

ME SPARES DL No 1001) GASKET FOR HEAT EXCHANGER PLATE part no.202-7533

ME SPARES DL No 1001) GASKET FOR HEAT EXCHANGER PLATE part no.202-7534

ME SPARES DL No 1001) GASKET FOR HEAT EXCHANGER PLATE part no.202-7536

SPARE LIST – DG KIRLOSKAR 6R 1080TA DL No 2030 FUEL FILTER CARTRIDGE DUPLEX TYPE part no.4H.333.03.0.00

SPARE LIST – DG KIRLOSKAR 6R 1080TA DL No 2030 V BELT (XPA 1250) COGGED part no.4H.069.01.0.00

SPARE LIST – DG KIRLOSKAR 6R 1080TA DL No 2030 PRIMARY ELEMENT part no.6H.411.02.0.00

SPARE LIST – DG KIRLOSKAR 6R 1080TA DL No 2030 LUB OIL FILTER part no.DV0.014.11.0.00

SPARE LIST – DG KIRLOSKAR 6R 1080TA DL No 2030 THERMOSTAT BYPASS HOSE part no.4H.023.02.0.00

SPARE LIST – DG KIRLOSKAR 6R 1080TA DL No 2030 L.O.SUPPLY HOSE (FIP) M10 BANJO ENDS X 235 L part no.4H.006.01.0.00

SPARE LIST – DG KIRLOSKAR 6R 1080TA DL No 2030 HOSE FOR AIR CLEANER part no.6H.466.47.0.00

SPARE LIST – DG KIRLOSKAR 6R 1080TA DL No 2030 RUBBER HOSE (FOR 'TR55' TURBO, COMPRESSOR OUTLET) part no.4H.168.11.0.00

SPARE LIST – DG KIRLOSKAR 6R 1080TA DL No 2030 HOSE T-BOLT CLAMP (DIA. 55-65) part no.4H.1712.24.0.00

SPARE LIST – DG KIRLOSKAR 6R 1080TA DL No 2030 WORM DRIVE HOSE CLIP (32 MM) part no.50.907.06.000.

SPARE LIST – DG KIRLOSKAR 6R 1080TA DL No 2030 HOSE STRAIGHT 70 MM LENGTH WITH CENTRAL HUMP part no.4H.366.07.0.00

SPARE LIST – DG KIRLOSKAR 6R 1080TA DL No 2030 LUB OIL SUPPLY HOSE (CRANK CASE TO FIP) FOR IRS part no.4H.333.01.0.00

SPARE LIST – DG KIRLOSKAR 6R 1080TA DL No 2030 KOEL CARE Genuine Coolant Premix 26 Litres Can part no.82.020.35.1.26

SPARE LIST – DG KIRLOSKAR 6R 1080TA DL No 2030 WATER PUMP SUB ASSEMBLY part no.4H.052.40.0.00

SPARE LIST – DG KIRLOSKAR 6R 1080TA DL No 2030 TURBOCHARGER (K26 2670 G 10.21) 9TEL PART NO . 5326 970 7018 ) part no.6H.029.10.0.00

SPARE LIST – DG KIRLOSKAR 6R 1080TA DL No 2030 JOINT SS (FOR TURBOCHARGER) part no. 6H.029.01.0.00

SPARE LIST – DG KIRLOSKAR 6R 1080TA DL No 2030 SS JOINT FOR TURBO OUTLET part no. 6H.026.02.0.00

SPARE LIST – DG KIRLOSKAR 6R 1080TA DL No 2030 HEAT EXCHANGER part no.4H.465.16.0.PR

SPARE LIST – DG KIRLOSKAR 6R 1080TA DL No 2030 LUB OIL COOLER ASSEMBLY part no. 6H.113.60.0.00

SPARE LIST – DG KIRLOSKAR 6R 1080TA DL No 2030 HEADER AND COOLER ASSEMBLY part no. 6H.113.50.0.00

HRP SPARES (DL 1003) GA (build up) HRP 4111; PS unit CCW, Drawing No. 12031091502, Part list no. 120310915. Anode set

Description:Lower Gearbox CW HRP 4111 WM, Drawing No. 0803X40003, Part list no. 080210915. Complete Seal Set Of Lower Gearbox

Description:Lower Gearbox CW HRP 4111 WM, Drawing No. 0803X40003, Part list no. 080210915. Parallel key part code.0930X400 pos.30

Description:Lower Gearbox CW HRP 4111 WM, Drawing No. 0803X40003, Part list no. 080210915. Socket head cap screw part code.3000000241 pos.31

Description:Lower Gearbox CW HRP 4111 WM, Drawing No. 0803X40003, Part list no. 080210915. Hexagon head bolt part code.3000000076 pos.34

Description:Lower Gearbox CW HRP 4111 WM, Drawing No. 0803X40003, Part list no. 080210915. Liner part code.0937X400 pos.37

Description:Lower Gearbox CW HRP 4111 WM, Drawing No. 0803X40003, Part list no. 080210915. Hexagon head screw partcode.3000000049 pos.26

Description:Lower Gearbox CW HRP 4111 WM, Drawing No. 0803X40003, Part list no. 080210915. Seal cover plate part code.0925X400 pos.25

Description:Lower Gearbox CW HRP 4111 WM, Drawing No. 0803X40003, Part list no. 080210915. Socket head cap screw partcode.3000000124 pos.5

Description:Lower Gearbox CW HRP 4111 WM, Drawing No. 0803X40003, Part list no. 080210915. Socket head cap screw partcode.3000000124 pos.6

Description:Lower Gearbox CW HRP 4111 WM, Drawing No. 0803X40003, Part list no. 080210915. Socket head cap screw partcode.3000000158 pos.17

Description:Lower Gearbox CW HRP 4111 WM, Drawing No. 0803X40003, Part list no. 080210915. G 1/4" part code.3000000896 pos.214

Description:Lower Gearbox CW HRP 4111 WM, Drawing No. 0803X40003, Part list no. 080210915. Washer part code.3500000032 pos189

Description:Lower Gearbox CW HRP 4111 WM, Drawing No. 0803X40003, Part list no. 080210915. Anode part code.1200000027 pos.190

Description:Lower Gearbox CW HRP 4111 WM, Drawing No. 0803X40003, Part list no. 080210915. Hexagon head screw part code3000000509 pos.191

HRP (DL 1003) MISC spares Filter Element (Lub)

Filter Element (Hyd)

Filter Element (WOC)

Seal Set Lub Oil filter

Seal Set Hyd Oil filter

Seal Set WOC Oil filter

Cooler maintenance kit for Lub Oil

Cooler maintenance kit for WOC.

Cooler maintenance kit for Hydraolic system.

SRP SW COOLER

Mandatory Spares Control Tug Baldev_HRP Order No # 10918 Serial No: 10918 04 2011 01 (Stbd) 10918 04 2011 02 (Port) Steering PCB part no.77.00.0002.00

Mandatory items Thrust PCB part no 77.00.0025.07

Mandatory items Clutch spool valve part no.8000001240

Mandatory items Clutch Coil part no.8000001241

Mandatory items Clutch Oil Pressure controller part no.8000001244

Mandatory items Clutch oil level switch part no.9000001007

Mandatory items Thermostat part no.9000000616

Anticipatory items RAI Buffer Unit Part No.77.73.0043.00

Anticipatory items DC/DC Passive Isolator Part No.78.71.0461.00

Anticipatory items Panel transfer Unit Part No.77.73.0034.01

Anticipatory items HPU Order handle Part No.77.73.0101.00

Anticipatory items LED Bar (0-10v)(0-600RPM) Part No.77.32.0055.00

Anticipatory items Thruster Feedback Unit Part No.77.08.0401.01

Anticipatory items Hyd. Oil Clogging Indicator Dwg No. 42021091500 Pos 60

Anticipatory items Hyd. Oil Temp Thermostate Dwg No. 42021091500 Pos 20

Anticipatory items Hyd. Oil level Switch Dwg No. 42021091500 Pos 16

Anticipatory items Hyd. Oil level Switch Dwg No. 42021091500 Pos 17

Anticipatory items Hyd. Oil Pressure Switch Dwg No. 42021091500 Pos 670

Anticipatory items Fuse F1 20Amps (6.3 x 32)

Anticipatory items Fuse F2 10Amps (6.3 x 25.4)

Anticipatory items Fuse F3 5Amps (6.3 x 25.4)

Anticipatory items Fuse F4 4Amps (5 x 20)

Anticipatory items Fuse F5 2Amps (5 x 20)

Anticipatory items Fuse F6 250mA (5 x 20)

Anticipatory Spares HRP Order Number- 10918 Description:Stem Section HRP 4111 WM (SB), Drawing No. 17011091500, Part list no. 170110915. Note: The spares indicated at Serials 809 to 0833 are anticpatory category only and firms are requested to quote for the same. However, the cost of the same will not be considered for determination of L1.

Complete Seal Set Of Stem section

Parallel pin Part code:3600000079 Pos No.18

Needle roll. Bearing Part code:4000000083 Pos No.6

Retaining ring Part code:3900000060 Pos No.8

Hexagon head bolt Part code:3000000445 Pos No.29

Steering pipe liner Part code:1980X4000 Pos No.4

Full compl.cyl.roll.bear Part code:4000000156 Pos No.11

Retaining ring Part code:3900000061 Pos No.13

Spacer Part code:1917Z4000 Pos No.12

Retaining ring Part code:3900000009 Pos No.14

Hexagon head bolt Part code:3000000061 Pos No.28

Hexagon head bolt Part code:3000000065 Pos No.16

Washer Part code:3500000053 Pos No.17

Description:Upper Gearbox CW HRP 4111 WM (WOC), Drawing No. 0614z40000, Part list no. 060210915.

Complete Seal Set Of Upper GB

Liner Part code:0752Z234 Pos No.52

Taper roller bearing Part code:4000000009 Pos No.16

Description:Clutch assembly HRP 4000 WOC, Drawing No. 41200Z400000, Part list no. 4120010915.

Complete Seal Set Of WOC

Liner Part code:4137Z4000 Pos No.7

Socket set screw Part code:3000000096 Pos No.8

Description:Steering section assembly, Drawing No. 0650Z40004, Part list no. 0650Z400. Complete Seal Set Of Steering section

Description:Clutch HRP 4000 WOC, Drawing No. 41201Z400001, Part list no.41201Z4000.

Complete Seal Set Of Clutch HRP 4000 WOC

Spring Part code:1200000819 pos No.17

WINTECH ENGINEERING WORKS

YEOMAN MARINE SERVICES PVT. LTD.

Patel Engineering Works Vizag

SAGAR SHIP REPAIRERS AND MARINE SERVICES

Sadhav Offshore Engineering Company

CARE MARINE AND ALLIED SERVICES

MARINE CARE N ASSOCIATES